blob: 042c0415140b1847e06afe4c7c9b426ab04f325f [file] [log] [blame]
Kernel driver it87
Supported chips:
* IT8705F
Prefix: 'it87'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Publicly available at the ITE website
* IT8712F
Prefix: 'it8712'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Publicly available at the ITE website
* IT8716F/IT8726F
Prefix: 'it8716'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Publicly available at the ITE website
* IT8718F
Prefix: 'it8718'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Publicly available at the ITE website
* SiS950 [clone of IT8705F]
Prefix: 'it87'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: No longer be available
Christophe Gauthron
Jean Delvare <>
Module Parameters
* update_vbat: int
0 if vbat should report power on value, 1 if vbat should be updated after
each read. Default is 0. On some boards the battery voltage is provided
by either the battery or the onboard power supply. Only the first reading
at power on will be the actual battery voltage (which the chip does
automatically). On other boards the battery voltage is always fed to
the chip so can be read at any time. Excessive reading may decrease
battery life but no information is given in the datasheet.
* fix_pwm_polarity int
Force PWM polarity to active high (DANGEROUS). Some chips are
misconfigured by BIOS - PWM values would be inverted. This option tries
to fix this. Please contact your BIOS manufacturer and ask him for fix.
Hardware Interfaces
All the chips suported by this driver are LPC Super-I/O chips, accessed
through the LPC bus (ISA-like I/O ports). The IT8712F additionally has an
SMBus interface to the hardware monitoring functions. This driver no
longer supports this interface though, as it is slower and less reliable
than the ISA access, and was only available on a small number of
motherboard models.
This driver implements support for the IT8705F, IT8712F, IT8716F,
IT8718F, IT8726F and SiS950 chips.
These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
joysticks and other miscellaneous stuff. For hardware monitoring, they
include an 'environment controller' with 3 temperature sensors, 3 fan
rotation speed sensors, 8 voltage sensors, and associated alarms.
The IT8712F and IT8716F additionally feature VID inputs, used to report
the Vcore voltage of the processor. The early IT8712F have 5 VID pins,
the IT8716F and late IT8712F have 6. They are shared with other functions
though, so the functionality may not be available on a given system.
The driver dumbly assume it is there.
The IT8718F also features VID inputs (up to 8 pins) but the value is
stored in the Super-I/O configuration space. Due to technical limitations,
this value can currently only be read once at initialization time, so
the driver won't notice and report changes in the VID value. The two
upper VID bits share their pins with voltage inputs (in5 and in6) so you
can't have both on a given board.
The IT8716F, IT8718F and later IT8712F revisions have support for
2 additional fans. The additional fans are supported by the driver.
The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
16-bit tachometer counters for fans 1 to 3. This is better (no more fan
clock divider mess) but not compatible with the older chips and
revisions. The 16-bit tachometer mode is enabled by the driver when one
of the above chips is detected.
The IT8726F is just bit enhanced IT8716F with additional hardware
for AMD power sequencing. Therefore the chip will appear as IT8716F
to userspace applications.
Temperatures are measured in degrees Celsius. An alarm is triggered once
when the Overtemperature Shutdown limit is crossed.
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
triggered if the rotation speed has dropped below a programmable limit. When
16-bit tachometer counters aren't used, fan readings can be divided by
a programmable divider (1, 2, 4 or 8) to give the readings more range or
accuracy. With a divider of 2, the lowest representable value is around
2600 RPM. Not all RPM values can accurately be represented, so some rounding
is done.
Voltage sensors (also known as IN sensors) report their values in volts. An
alarm is triggered if the voltage has crossed a programmable minimum or
maximum limit. Note that minimum in this case always means 'closest to
zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 4.08 volts, with a resolution of
0.016 volt. The battery voltage in8 does not have limit registers.
The VID lines (IT8712F/IT8716F/IT8718F) encode the core voltage value:
the voltage level your processor should work with. This is hardcoded by
the mainboard and/or processor itself. It is a value in volts.
If an alarm triggers, it will remain triggered until the hardware register
is read at least once. This means that the cause for the alarm may already
have disappeared! Note that in the current implementation, all hardware
registers are read whenever any data is read (unless it is less than 1.5
seconds since the last update). This means that you can easily miss
once-only alarms.
The IT87xx only updates its values each 1.5 seconds; reading it more often
will do no harm, but will return 'old' values.
To change sensor N to a thermistor, 'echo 4 > tempN_type' where N is 1, 2,
or 3. To change sensor N to a thermal diode, 'echo 3 > tempN_type'.
Give 0 for unused sensor. Any other value is invalid. To configure this at
startup, consult lm_sensors's /etc/sensors.conf. (4 = thermistor;
3 = thermal diode)
Fan speed control
The fan speed control features are limited to manual PWM mode. Automatic
"Smart Guardian" mode control handling is not implemented. However
if you want to go for "manual mode" just write 1 to pwmN_enable.
If you are only able to control the fan speed with very small PWM values,
try lowering the PWM base frequency (pwm1_freq). Depending on the fan,
it may give you a somewhat greater control range. The same frequency is
used to drive all fan outputs, which is why pwm2_freq and pwm3_freq are