blob: ed48d75bb7866fe306dea509d450fb64fde8c7e5 [file] [log] [blame]
/*
* Copyright 2012 ST Ericsson.
*
* Power supply driver for ST Ericsson pm2xxx_charger charger
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/power_supply.h>
#include <linux/completion.h>
#include <linux/regulator/consumer.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/workqueue.h>
#include <linux/kobject.h>
#include <linux/mfd/abx500.h>
#include <linux/mfd/abx500/ab8500.h>
#include <linux/mfd/abx500/ab8500-bm.h>
#include <linux/mfd/abx500/ab8500-gpadc.h>
#include <linux/mfd/abx500/ux500_chargalg.h>
#include <linux/pm2301_charger.h>
#include <linux/gpio.h>
#include "pm2301_charger.h"
#define to_pm2xxx_charger_ac_device_info(x) container_of((x), \
struct pm2xxx_charger, ac_chg)
static int pm2xxx_interrupt_registers[] = {
PM2XXX_REG_INT1,
PM2XXX_REG_INT2,
PM2XXX_REG_INT3,
PM2XXX_REG_INT4,
PM2XXX_REG_INT5,
PM2XXX_REG_INT6,
};
static enum power_supply_property pm2xxx_charger_ac_props[] = {
POWER_SUPPLY_PROP_HEALTH,
POWER_SUPPLY_PROP_PRESENT,
POWER_SUPPLY_PROP_ONLINE,
POWER_SUPPLY_PROP_VOLTAGE_AVG,
};
static int pm2xxx_charger_voltage_map[] = {
3500,
3525,
3550,
3575,
3600,
3625,
3650,
3675,
3700,
3725,
3750,
3775,
3800,
3825,
3850,
3875,
3900,
3925,
3950,
3975,
4000,
4025,
4050,
4075,
4100,
4125,
4150,
4175,
4200,
4225,
4250,
4275,
4300,
};
static int pm2xxx_charger_current_map[] = {
200,
200,
400,
600,
800,
1000,
1200,
1400,
1600,
1800,
2000,
2200,
2400,
2600,
2800,
3000,
};
static const struct i2c_device_id pm2xxx_ident[] = {
{ "pm2301", 0 },
{ }
};
static void set_lpn_pin(struct pm2xxx_charger *pm2)
{
if (pm2->ac.charger_connected)
return;
gpio_set_value(pm2->lpn_pin, 1);
return;
}
static void clear_lpn_pin(struct pm2xxx_charger *pm2)
{
if (pm2->ac.charger_connected)
return;
gpio_set_value(pm2->lpn_pin, 0);
return;
}
static int pm2xxx_reg_read(struct pm2xxx_charger *pm2, int reg, u8 *val)
{
int ret;
/*
* When AC adaptor is unplugged, the host
* must put LPN high to be able to
* communicate by I2C with PM2301
* and receive I2C "acknowledge" from PM2301.
*/
mutex_lock(&pm2->lock);
set_lpn_pin(pm2);
ret = i2c_smbus_read_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
1, val);
if (ret < 0)
dev_err(pm2->dev, "Error reading register at 0x%x\n", reg);
else
ret = 0;
clear_lpn_pin(pm2);
mutex_unlock(&pm2->lock);
return ret;
}
static int pm2xxx_reg_write(struct pm2xxx_charger *pm2, int reg, u8 val)
{
int ret;
/*
* When AC adaptor is unplugged, the host
* must put LPN high to be able to
* communicate by I2C with PM2301
* and receive I2C "acknowledge" from PM2301.
*/
mutex_lock(&pm2->lock);
set_lpn_pin(pm2);
ret = i2c_smbus_write_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
1, &val);
if (ret < 0)
dev_err(pm2->dev, "Error writing register at 0x%x\n", reg);
else
ret = 0;
clear_lpn_pin(pm2);
mutex_unlock(&pm2->lock);
return ret;
}
static int pm2xxx_charging_enable_mngt(struct pm2xxx_charger *pm2)
{
int ret;
/* Enable charging */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
(PM2XXX_CH_AUTO_RESUME_EN | PM2XXX_CHARGER_ENA));
return ret;
}
static int pm2xxx_charging_disable_mngt(struct pm2xxx_charger *pm2)
{
int ret;
/* Disable charging */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
(PM2XXX_CH_AUTO_RESUME_DIS | PM2XXX_CHARGER_DIS));
return ret;
}
static int pm2xxx_charger_batt_therm_mngt(struct pm2xxx_charger *pm2, int val)
{
queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
return 0;
}
int pm2xxx_charger_die_therm_mngt(struct pm2xxx_charger *pm2, int val)
{
queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
return 0;
}
static int pm2xxx_charger_ovv_mngt(struct pm2xxx_charger *pm2, int val)
{
int ret = 0;
pm2->failure_input_ovv++;
if (pm2->failure_input_ovv < 4) {
ret = pm2xxx_charging_enable_mngt(pm2);
goto out;
} else {
pm2->failure_input_ovv = 0;
dev_err(pm2->dev, "Overvoltage detected\n");
pm2->flags.ovv = true;
power_supply_changed(&pm2->ac_chg.psy);
}
out:
return ret;
}
static int pm2xxx_charger_wd_exp_mngt(struct pm2xxx_charger *pm2, int val)
{
dev_dbg(pm2->dev , "20 minutes watchdog occured\n");
pm2->ac.wd_expired = true;
power_supply_changed(&pm2->ac_chg.psy);
return 0;
}
static int pm2xxx_charger_vbat_lsig_mngt(struct pm2xxx_charger *pm2, int val)
{
switch (val) {
case PM2XXX_INT1_ITVBATLOWR:
dev_dbg(pm2->dev, "VBAT grows above VBAT_LOW level\n");
break;
case PM2XXX_INT1_ITVBATLOWF:
dev_dbg(pm2->dev, "VBAT drops below VBAT_LOW level\n");
break;
default:
dev_err(pm2->dev, "Unknown VBAT level\n");
}
return 0;
}
static int pm2xxx_charger_bat_disc_mngt(struct pm2xxx_charger *pm2, int val)
{
dev_dbg(pm2->dev, "battery disconnected\n");
return 0;
}
static int pm2xxx_charger_detection(struct pm2xxx_charger *pm2, u8 *val)
{
int ret;
ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT2, val);
if (ret < 0) {
dev_err(pm2->dev, "Charger detection failed\n");
goto out;
}
*val &= (PM2XXX_INT2_S_ITVPWR1PLUG | PM2XXX_INT2_S_ITVPWR2PLUG);
out:
return ret;
}
static int pm2xxx_charger_itv_pwr_plug_mngt(struct pm2xxx_charger *pm2, int val)
{
int ret;
u8 read_val;
/*
* Since we can't be sure that the events are received
* synchronously, we have the check if the main charger is
* connected by reading the interrupt source register.
*/
ret = pm2xxx_charger_detection(pm2, &read_val);
if ((ret == 0) && read_val) {
pm2->ac.charger_connected = 1;
pm2->ac_conn = true;
queue_work(pm2->charger_wq, &pm2->ac_work);
}
return ret;
}
static int pm2xxx_charger_itv_pwr_unplug_mngt(struct pm2xxx_charger *pm2,
int val)
{
pm2->ac.charger_connected = 0;
queue_work(pm2->charger_wq, &pm2->ac_work);
return 0;
}
static int pm2_int_reg0(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT1_ITVBATLOWR | PM2XXX_INT1_ITVBATLOWF)) {
ret = pm2xxx_charger_vbat_lsig_mngt(pm2, val &
(PM2XXX_INT1_ITVBATLOWR | PM2XXX_INT1_ITVBATLOWF));
}
if (val & PM2XXX_INT1_ITVBATDISCONNECT) {
ret = pm2xxx_charger_bat_disc_mngt(pm2,
PM2XXX_INT1_ITVBATDISCONNECT);
}
return ret;
}
static int pm2_int_reg1(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG)) {
dev_dbg(pm2->dev , "Main charger plugged\n");
ret = pm2xxx_charger_itv_pwr_plug_mngt(pm2, val &
(PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG));
}
if (val &
(PM2XXX_INT2_ITVPWR1UNPLUG | PM2XXX_INT2_ITVPWR2UNPLUG)) {
dev_dbg(pm2->dev , "Main charger unplugged\n");
ret = pm2xxx_charger_itv_pwr_unplug_mngt(pm2, val &
(PM2XXX_INT2_ITVPWR1UNPLUG |
PM2XXX_INT2_ITVPWR2UNPLUG));
}
return ret;
}
static int pm2_int_reg2(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & PM2XXX_INT3_ITAUTOTIMEOUTWD)
ret = pm2xxx_charger_wd_exp_mngt(pm2, val);
if (val & (PM2XXX_INT3_ITCHPRECHARGEWD |
PM2XXX_INT3_ITCHCCWD | PM2XXX_INT3_ITCHCVWD)) {
dev_dbg(pm2->dev,
"Watchdog occured for precharge, CC and CV charge\n");
}
return ret;
}
static int pm2_int_reg3(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT4_ITCHARGINGON)) {
dev_dbg(pm2->dev ,
"chargind operation has started\n");
}
if (val & (PM2XXX_INT4_ITVRESUME)) {
dev_dbg(pm2->dev,
"battery discharged down to VResume threshold\n");
}
if (val & (PM2XXX_INT4_ITBATTFULL)) {
dev_dbg(pm2->dev , "battery fully detected\n");
}
if (val & (PM2XXX_INT4_ITCVPHASE)) {
dev_dbg(pm2->dev, "CV phase enter with 0.5C charging\n");
}
if (val & (PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV)) {
pm2->failure_case = VPWR_OVV;
ret = pm2xxx_charger_ovv_mngt(pm2, val &
(PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV));
dev_dbg(pm2->dev, "VPWR/VSYSTEM overvoltage detected\n");
}
if (val & (PM2XXX_INT4_S_ITBATTEMPCOLD |
PM2XXX_INT4_S_ITBATTEMPHOT)) {
ret = pm2xxx_charger_batt_therm_mngt(pm2, val &
(PM2XXX_INT4_S_ITBATTEMPCOLD |
PM2XXX_INT4_S_ITBATTEMPHOT));
dev_dbg(pm2->dev, "BTEMP is too Low/High\n");
}
return ret;
}
static int pm2_int_reg4(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & PM2XXX_INT5_ITVSYSTEMOVV) {
pm2->failure_case = VSYSTEM_OVV;
ret = pm2xxx_charger_ovv_mngt(pm2, val &
PM2XXX_INT5_ITVSYSTEMOVV);
dev_dbg(pm2->dev, "VSYSTEM overvoltage detected\n");
}
if (val & (PM2XXX_INT5_ITTHERMALWARNINGFALL |
PM2XXX_INT5_ITTHERMALWARNINGRISE |
PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
PM2XXX_INT5_ITTHERMALSHUTDOWNRISE)) {
dev_dbg(pm2->dev, "BTEMP die temperature is too Low/High\n");
ret = pm2xxx_charger_die_therm_mngt(pm2, val &
(PM2XXX_INT5_ITTHERMALWARNINGFALL |
PM2XXX_INT5_ITTHERMALWARNINGRISE |
PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
PM2XXX_INT5_ITTHERMALSHUTDOWNRISE));
}
return ret;
}
static int pm2_int_reg5(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT6_ITVPWR2DROP | PM2XXX_INT6_ITVPWR1DROP)) {
dev_dbg(pm2->dev, "VMPWR drop to VBAT level\n");
}
if (val & (PM2XXX_INT6_ITVPWR2VALIDRISE |
PM2XXX_INT6_ITVPWR1VALIDRISE |
PM2XXX_INT6_ITVPWR2VALIDFALL |
PM2XXX_INT6_ITVPWR1VALIDFALL)) {
dev_dbg(pm2->dev, "Falling/Rising edge on WPWR1/2\n");
}
return ret;
}
static irqreturn_t pm2xxx_irq_int(int irq, void *data)
{
struct pm2xxx_charger *pm2 = data;
struct pm2xxx_interrupts *interrupt = pm2->pm2_int;
int i;
for (i = 0; i < PM2XXX_NUM_INT_REG; i++) {
pm2xxx_reg_read(pm2,
pm2xxx_interrupt_registers[i],
&(interrupt->reg[i]));
if (interrupt->reg[i] > 0)
interrupt->handler[i](pm2, interrupt->reg[i]);
}
return IRQ_HANDLED;
}
static int pm2xxx_charger_get_ac_cv(struct pm2xxx_charger *pm2)
{
int ret = 0;
u8 val;
if (pm2->ac.charger_connected && pm2->ac.charger_online) {
ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT4, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
goto out;
}
if (val & PM2XXX_INT4_S_ITCVPHASE)
ret = PM2XXX_CONST_VOLT;
else
ret = PM2XXX_CONST_CURR;
}
out:
return ret;
}
static int pm2xxx_current_to_regval(int curr)
{
int i;
if (curr < pm2xxx_charger_current_map[0])
return 0;
for (i = 1; i < ARRAY_SIZE(pm2xxx_charger_current_map); i++) {
if (curr < pm2xxx_charger_current_map[i])
return (i - 1);
}
i = ARRAY_SIZE(pm2xxx_charger_current_map) - 1;
if (curr == pm2xxx_charger_current_map[i])
return i;
else
return -EINVAL;
}
static int pm2xxx_voltage_to_regval(int curr)
{
int i;
if (curr < pm2xxx_charger_voltage_map[0])
return 0;
for (i = 1; i < ARRAY_SIZE(pm2xxx_charger_voltage_map); i++) {
if (curr < pm2xxx_charger_voltage_map[i])
return i - 1;
}
i = ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1;
if (curr == pm2xxx_charger_voltage_map[i])
return i;
else
return -EINVAL;
}
static int pm2xxx_charger_update_charger_current(struct ux500_charger *charger,
int ich_out)
{
int ret;
int curr_index;
struct pm2xxx_charger *pm2;
u8 val;
if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
pm2 = to_pm2xxx_charger_ac_device_info(charger);
else
return -ENXIO;
curr_index = pm2xxx_current_to_regval(ich_out);
if (curr_index < 0) {
dev_err(pm2->dev,
"Charger current too high, charging not started\n");
return -ENXIO;
}
ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6, &val);
if (ret >= 0) {
val &= ~PM2XXX_DIR_CH_CC_CURRENT_MASK;
val |= curr_index;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, val);
if (ret < 0) {
dev_err(pm2->dev,
"%s write failed\n", __func__);
}
}
else
dev_err(pm2->dev, "%s read failed\n", __func__);
return ret;
}
static int pm2xxx_charger_ac_get_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
{
struct pm2xxx_charger *pm2;
pm2 = to_pm2xxx_charger_ac_device_info(psy_to_ux500_charger(psy));
switch (psp) {
case POWER_SUPPLY_PROP_HEALTH:
if (pm2->flags.mainextchnotok)
val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
else if (pm2->ac.wd_expired)
val->intval = POWER_SUPPLY_HEALTH_DEAD;
else if (pm2->flags.main_thermal_prot)
val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
else
val->intval = POWER_SUPPLY_HEALTH_GOOD;
break;
case POWER_SUPPLY_PROP_ONLINE:
val->intval = pm2->ac.charger_online;
break;
case POWER_SUPPLY_PROP_PRESENT:
val->intval = pm2->ac.charger_connected;
break;
case POWER_SUPPLY_PROP_VOLTAGE_AVG:
pm2->ac.cv_active = pm2xxx_charger_get_ac_cv(pm2);
val->intval = pm2->ac.cv_active;
break;
default:
return -EINVAL;
}
return 0;
}
static int pm2xxx_charging_init(struct pm2xxx_charger *pm2)
{
int ret = 0;
/* enable CC and CV watchdog */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG3,
(PM2XXX_CH_WD_CV_PHASE_60MIN | PM2XXX_CH_WD_CC_PHASE_60MIN));
if( ret < 0)
return ret;
/* enable precharge watchdog */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG4,
PM2XXX_CH_WD_PRECH_PHASE_60MIN);
/* Disable auto timeout */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG5,
PM2XXX_CH_WD_AUTO_TIMEOUT_20MIN);
/*
* EOC current level = 100mA
* Precharge current level = 100mA
* CC current level = 1000mA
*/
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6,
(PM2XXX_DIR_CH_CC_CURRENT_1000MA |
PM2XXX_CH_PRECH_CURRENT_100MA |
PM2XXX_CH_EOC_CURRENT_100MA));
/*
* recharge threshold = 3.8V
* Precharge to CC threshold = 2.9V
*/
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG7,
(PM2XXX_CH_PRECH_VOL_2_9 | PM2XXX_CH_VRESUME_VOL_3_8));
/* float voltage charger level = 4.2V */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8,
PM2XXX_CH_VOLT_4_2);
/* Voltage drop between VBAT and VSYS in HW charging = 300mV */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG9,
(PM2XXX_CH_150MV_DROP_300MV | PM2XXX_CHARCHING_INFO_DIS |
PM2XXX_CH_CC_REDUCED_CURRENT_IDENT |
PM2XXX_CH_CC_MODEDROP_DIS));
/* Input charger level of over voltage = 10V */
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_VOLT_VPWR2,
PM2XXX_VPWR2_OVV_10);
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_VOLT_VPWR1,
PM2XXX_VPWR1_OVV_10);
/* Input charger drop */
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_DROP_VPWR2,
(PM2XXX_VPWR2_HW_OPT_DIS | PM2XXX_VPWR2_VALID_DIS |
PM2XXX_VPWR2_DROP_DIS));
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_DROP_VPWR1,
(PM2XXX_VPWR1_HW_OPT_DIS | PM2XXX_VPWR1_VALID_DIS |
PM2XXX_VPWR1_DROP_DIS));
/* Disable battery low monitoring */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_LOW_LEV_COMP_REG,
PM2XXX_VBAT_LOW_MONITORING_ENA);
/* Disable LED */
ret = pm2xxx_reg_write(pm2, PM2XXX_LED_CTRL_REG,
PM2XXX_LED_SELECT_DIS);
return ret;
}
static int pm2xxx_charger_ac_en(struct ux500_charger *charger,
int enable, int vset, int iset)
{
int ret;
int volt_index;
int curr_index;
u8 val;
struct pm2xxx_charger *pm2 = to_pm2xxx_charger_ac_device_info(charger);
if (enable) {
if (!pm2->ac.charger_connected) {
dev_dbg(pm2->dev, "AC charger not connected\n");
return -ENXIO;
}
dev_dbg(pm2->dev, "Enable AC: %dmV %dmA\n", vset, iset);
if (!pm2->vddadc_en_ac) {
regulator_enable(pm2->regu);
pm2->vddadc_en_ac = true;
}
ret = pm2xxx_charging_init(pm2);
if (ret < 0) {
dev_err(pm2->dev, "%s charging init failed\n",
__func__);
goto error_occured;
}
volt_index = pm2xxx_voltage_to_regval(vset);
curr_index = pm2xxx_current_to_regval(iset);
if (volt_index < 0 || curr_index < 0) {
dev_err(pm2->dev,
"Charger voltage or current too high, "
"charging not started\n");
return -ENXIO;
}
ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG8, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
goto error_occured;
}
val &= ~PM2XXX_CH_VOLT_MASK;
val |= volt_index;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8, val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
goto error_occured;
}
ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
goto error_occured;
}
val &= ~PM2XXX_DIR_CH_CC_CURRENT_MASK;
val |= curr_index;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
goto error_occured;
}
if (!pm2->bat->enable_overshoot) {
ret = pm2xxx_reg_read(pm2, PM2XXX_LED_CTRL_REG, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n",
__func__);
goto error_occured;
}
val |= PM2XXX_ANTI_OVERSHOOT_EN;
ret = pm2xxx_reg_write(pm2, PM2XXX_LED_CTRL_REG, val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n",
__func__);
goto error_occured;
}
}
ret = pm2xxx_charging_enable_mngt(pm2);
if (ret < 0) {
dev_err(pm2->dev, "Failed to enable"
"pm2xxx ac charger\n");
goto error_occured;
}
pm2->ac.charger_online = 1;
} else {
pm2->ac.charger_online = 0;
pm2->ac.wd_expired = false;
/* Disable regulator if enabled */
if (pm2->vddadc_en_ac) {
regulator_disable(pm2->regu);
pm2->vddadc_en_ac = false;
}
ret = pm2xxx_charging_disable_mngt(pm2);
if (ret < 0) {
dev_err(pm2->dev, "failed to disable"
"pm2xxx ac charger\n");
goto error_occured;
}
dev_dbg(pm2->dev, "PM2301: " "Disabled AC charging\n");
}
power_supply_changed(&pm2->ac_chg.psy);
error_occured:
return ret;
}
static int pm2xxx_charger_watchdog_kick(struct ux500_charger *charger)
{
int ret;
struct pm2xxx_charger *pm2;
if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
pm2 = to_pm2xxx_charger_ac_device_info(charger);
else
return -ENXIO;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_WD_KICK, WD_TIMER);
if (ret)
dev_err(pm2->dev, "Failed to kick WD!\n");
return ret;
}
static void pm2xxx_charger_ac_work(struct work_struct *work)
{
struct pm2xxx_charger *pm2 = container_of(work,
struct pm2xxx_charger, ac_work);
power_supply_changed(&pm2->ac_chg.psy);
sysfs_notify(&pm2->ac_chg.psy.dev->kobj, NULL, "present");
};
static void pm2xxx_charger_check_main_thermal_prot_work(
struct work_struct *work)
{
};
static struct pm2xxx_interrupts pm2xxx_int = {
.handler[0] = pm2_int_reg0,
.handler[1] = pm2_int_reg1,
.handler[2] = pm2_int_reg2,
.handler[3] = pm2_int_reg3,
.handler[4] = pm2_int_reg4,
.handler[5] = pm2_int_reg5,
};
static struct pm2xxx_irq pm2xxx_charger_irq[] = {
{"PM2XXX_IRQ_INT", pm2xxx_irq_int},
};
static int pm2xxx_wall_charger_resume(struct i2c_client *i2c_client)
{
return 0;
}
static int pm2xxx_wall_charger_suspend(struct i2c_client *i2c_client,
pm_message_t state)
{
return 0;
}
static int __devinit pm2xxx_wall_charger_probe(struct i2c_client *i2c_client,
const struct i2c_device_id *id)
{
struct pm2xxx_platform_data *pl_data = i2c_client->dev.platform_data;
struct pm2xxx_charger *pm2;
int ret = 0;
u8 val;
pm2 = kzalloc(sizeof(struct pm2xxx_charger), GFP_KERNEL);
if (!pm2) {
dev_err(pm2->dev, "pm2xxx_charger allocation failed\n");
return -ENOMEM;
}
/* get parent data */
pm2->dev = &i2c_client->dev;
pm2->gpadc = ab8500_gpadc_get("ab8500-gpadc.0");
pm2->pm2_int = &pm2xxx_int;
/* get charger spcific platform data */
if (!pl_data->wall_charger) {
dev_err(pm2->dev, "no charger platform data supplied\n");
ret = -EINVAL;
goto free_device_info;
}
pm2->pdata = pl_data->wall_charger;
/* get battery specific platform data */
if (!pl_data->battery) {
dev_err(pm2->dev, "no battery platform data supplied\n");
ret = -EINVAL;
goto free_device_info;
}
pm2->bat = pl_data->battery;
/*get lpn GPIO from platform data*/
if (!pm2->pdata->lpn_gpio) {
dev_err(pm2->dev, "no lpn gpio data supplied\n");
ret = -EINVAL;
goto free_device_info;
}
pm2->lpn_pin = pm2->pdata->lpn_gpio;
if (!i2c_check_functionality(i2c_client->adapter,
I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_READ_WORD_DATA)) {
ret = -ENODEV;
dev_info(pm2->dev, "pm2301 i2c_check_functionality failed\n");
goto free_device_info;
}
pm2->config.pm2xxx_i2c = i2c_client;
pm2->config.pm2xxx_id = (struct i2c_device_id *) id;
i2c_set_clientdata(i2c_client, pm2);
/* AC supply */
/* power_supply base class */
pm2->ac_chg.psy.name = pm2->pdata->label;
pm2->ac_chg.psy.type = POWER_SUPPLY_TYPE_MAINS;
pm2->ac_chg.psy.properties = pm2xxx_charger_ac_props;
pm2->ac_chg.psy.num_properties = ARRAY_SIZE(pm2xxx_charger_ac_props);
pm2->ac_chg.psy.get_property = pm2xxx_charger_ac_get_property;
pm2->ac_chg.psy.supplied_to = pm2->pdata->supplied_to;
pm2->ac_chg.psy.num_supplicants = pm2->pdata->num_supplicants;
/* pm2xxx_charger sub-class */
pm2->ac_chg.ops.enable = &pm2xxx_charger_ac_en;
pm2->ac_chg.ops.kick_wd = &pm2xxx_charger_watchdog_kick;
pm2->ac_chg.ops.update_curr = &pm2xxx_charger_update_charger_current;
pm2->ac_chg.max_out_volt = pm2xxx_charger_voltage_map[
ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1];
pm2->ac_chg.max_out_curr = pm2xxx_charger_current_map[
ARRAY_SIZE(pm2xxx_charger_current_map) - 1];
pm2->ac_chg.wdt_refresh = WD_KICK_INTERVAL;
pm2->ac_chg.enabled = true;
pm2->ac_chg.external = true;
/* Create a work queue for the charger */
pm2->charger_wq =
create_singlethread_workqueue("pm2xxx_charger_wq");
if (pm2->charger_wq == NULL) {
dev_err(pm2->dev, "failed to create work queue\n");
goto free_device_info;
}
/* Init work for charger detection */
INIT_WORK(&pm2->ac_work, pm2xxx_charger_ac_work);
/* Init work for checking HW status */
INIT_WORK(&pm2->check_main_thermal_prot_work,
pm2xxx_charger_check_main_thermal_prot_work);
/*
* VDD ADC supply needs to be enabled from this driver when there
* is a charger connected to avoid erroneous BTEMP_HIGH/LOW
* interrupts during charging
*/
pm2->regu = regulator_get(pm2->dev, "vddadc");
if (IS_ERR(pm2->regu)) {
ret = PTR_ERR(pm2->regu);
dev_err(pm2->dev, "failed to get vddadc regulator\n");
goto free_charger_wq;
}
/* Register AC charger class */
ret = power_supply_register(pm2->dev, &pm2->ac_chg.psy);
if (ret) {
dev_err(pm2->dev, "failed to register AC charger\n");
goto free_regulator;
}
/* Register interrupts */
ret = request_threaded_irq(pm2->pdata->irq_number, NULL,
pm2xxx_charger_irq[0].isr,
pm2->pdata->irq_type,
pm2xxx_charger_irq[0].name, pm2);
if (ret != 0) {
dev_err(pm2->dev, "failed to request %s IRQ %d: %d\n",
pm2xxx_charger_irq[0].name, pm2->pdata->irq_number, ret);
goto unregister_pm2xxx_charger;
}
/*Initialize lock*/
mutex_init(&pm2->lock);
/*
* Charger detection mechanism requires pulling up the LPN pin
* while i2c communication if Charger is not connected
* LPN pin of PM2301 is GPIO60 of AB9540
*/
ret = gpio_request(pm2->lpn_pin, "pm2301_lpm_gpio");
if (ret < 0) {
dev_err(pm2->dev, "pm2301_lpm_gpio request failed\n");
goto unregister_pm2xxx_charger;
}
ret = gpio_direction_output(pm2->lpn_pin, 0);
if (ret < 0) {
dev_err(pm2->dev, "pm2301_lpm_gpio direction failed\n");
goto free_gpio;
}
ret = pm2xxx_charger_detection(pm2, &val);
if ((ret == 0) && val) {
pm2->ac.charger_connected = 1;
pm2->ac_conn = true;
power_supply_changed(&pm2->ac_chg.psy);
sysfs_notify(&pm2->ac_chg.psy.dev->kobj, NULL, "present");
}
return 0;
free_gpio:
gpio_free(pm2->lpn_pin);
unregister_pm2xxx_charger:
/* unregister power supply */
power_supply_unregister(&pm2->ac_chg.psy);
free_regulator:
/* disable the regulator */
regulator_put(pm2->regu);
free_charger_wq:
destroy_workqueue(pm2->charger_wq);
free_device_info:
kfree(pm2);
return ret;
}
static int __devexit pm2xxx_wall_charger_remove(struct i2c_client *i2c_client)
{
struct pm2xxx_charger *pm2 = i2c_get_clientdata(i2c_client);
/* Disable AC charging */
pm2xxx_charger_ac_en(&pm2->ac_chg, false, 0, 0);
/* Disable interrupts */
free_irq(pm2->pdata->irq_number, pm2);
/* Delete the work queue */
destroy_workqueue(pm2->charger_wq);
flush_scheduled_work();
/* disable the regulator */
regulator_put(pm2->regu);
power_supply_unregister(&pm2->ac_chg.psy);
/*Free GPIO60*/
gpio_free(pm2->lpn_pin);
kfree(pm2);
return 0;
}
static const struct i2c_device_id pm2xxx_id[] = {
{ "pm2301", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, pm2xxx_id);
static struct i2c_driver pm2xxx_charger_driver = {
.probe = pm2xxx_wall_charger_probe,
.remove = __devexit_p(pm2xxx_wall_charger_remove),
.suspend = pm2xxx_wall_charger_suspend,
.resume = pm2xxx_wall_charger_resume,
.driver = {
.name = "pm2xxx-wall_charger",
.owner = THIS_MODULE,
},
.id_table = pm2xxx_id,
};
static int __init pm2xxx_charger_init(void)
{
return i2c_add_driver(&pm2xxx_charger_driver);
}
static void __exit pm2xxx_charger_exit(void)
{
i2c_del_driver(&pm2xxx_charger_driver);
}
subsys_initcall_sync(pm2xxx_charger_init);
module_exit(pm2xxx_charger_exit);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
MODULE_ALIAS("platform:pm2xxx-charger");
MODULE_DESCRIPTION("PM2xxx charger management driver");