blob: fd57a81180a4759be7fcbfb4bf23ea3f2985bde7 [file] [log] [blame]
* Xilinx AXI PCIe Root Port Bridge DT description
Required properties:
- #address-cells: Address representation for root ports, set to <3>
- #size-cells: Size representation for root ports, set to <2>
- #interrupt-cells: specifies the number of cells needed to encode an
interrupt source. The value must be 1.
- compatible: Should contain "xlnx,axi-pcie-host-1.00.a"
- reg: Should contain AXI PCIe registers location and length
- device_type: must be "pci"
- interrupts: Should contain AXI PCIe interrupt
- interrupt-map-mask,
interrupt-map: standard PCI properties to define the mapping of the
PCI interface to interrupt numbers.
- ranges: ranges for the PCI memory regions (I/O space region is not
supported by hardware)
Please refer to the standard PCI bus binding document for a more
detailed explanation
Optional properties for Zynq/Microblaze:
- bus-range: PCI bus numbers covered
Interrupt controller child node
+++++++++++++++++++++++++++++++
Required properties:
- interrupt-controller: identifies the node as an interrupt controller
- #address-cells: specifies the number of cells needed to encode an
address. The value must be 0.
- #interrupt-cells: specifies the number of cells needed to encode an
interrupt source. The value must be 1.
NOTE:
The core provides a single interrupt for both INTx/MSI messages. So,
created a interrupt controller node to support 'interrupt-map' DT
functionality. The driver will create an IRQ domain for this map, decode
the four INTx interrupts in ISR and route them to this domain.
Example:
++++++++
Zynq:
pci_express: axi-pcie@50000000 {
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
compatible = "xlnx,axi-pcie-host-1.00.a";
reg = < 0x50000000 0x1000000 >;
device_type = "pci";
interrupts = < 0 52 4 >;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc 1>,
<0 0 0 2 &pcie_intc 2>,
<0 0 0 3 &pcie_intc 3>,
<0 0 0 4 &pcie_intc 4>;
ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >;
pcie_intc: interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
};
};
Microblaze:
pci_express: axi-pcie@10000000 {
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
compatible = "xlnx,axi-pcie-host-1.00.a";
reg = <0x10000000 0x4000000>;
device_type = "pci";
interrupt-parent = <&microblaze_0_intc>;
interrupts = <1 2>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc 1>,
<0 0 0 2 &pcie_intc 2>,
<0 0 0 3 &pcie_intc 3>,
<0 0 0 4 &pcie_intc 4>;
ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x10000000>;
pcie_intc: interrupt-controller {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
};
};