| #ifndef _HIL_H_ |
| #define _HIL_H_ |
| |
| /* |
| * Hewlett Packard Human Interface Loop (HP-HIL) Protocol -- header. |
| * |
| * Copyright (c) 2001 Brian S. Julin |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * 1. Redistributions of source code must retain the above copyright |
| * notice, this list of conditions, and the following disclaimer, |
| * without modification. |
| * 2. The name of the author may not be used to endorse or promote products |
| * derived from this software without specific prior written permission. |
| * |
| * Alternatively, this software may be distributed under the terms of the |
| * GNU General Public License ("GPL"). |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND |
| * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
| * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS |
| * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) |
| * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT |
| * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY |
| * |
| * References: |
| * HP-HIL Technical Reference Manual. Hewlett Packard Product No. 45918A |
| * |
| * A note of thanks to HP for providing and shipping reference materials |
| * free of charge to help in the development of HIL support for Linux. |
| * |
| */ |
| |
| #include <asm/types.h> |
| |
| /* Physical constants relevant to raw loop/device timing. |
| */ |
| |
| #define HIL_CLOCK 8MHZ |
| #define HIL_EK1_CLOCK 30HZ |
| #define HIL_EK2_CLOCK 60HZ |
| |
| #define HIL_TIMEOUT_DEV 5 /* ms */ |
| #define HIL_TIMEOUT_DEVS 10 /* ms */ |
| #define HIL_TIMEOUT_NORESP 10 /* ms */ |
| #define HIL_TIMEOUT_DEVS_DATA 16 /* ms */ |
| #define HIL_TIMEOUT_SELFTEST 200 /* ms */ |
| |
| |
| /* Actual wire line coding. These will only be useful if someone is |
| * implementing a software MLC to run HIL devices on a non-parisc machine. |
| */ |
| |
| #define HIL_WIRE_PACKET_LEN 15 |
| enum hil_wire_bitpos { |
| HIL_WIRE_START = 0, |
| HIL_WIRE_ADDR2, |
| HIL_WIRE_ADDR1, |
| HIL_WIRE_ADDR0, |
| HIL_WIRE_COMMAND, |
| HIL_WIRE_DATA7, |
| HIL_WIRE_DATA6, |
| HIL_WIRE_DATA5, |
| HIL_WIRE_DATA4, |
| HIL_WIRE_DATA3, |
| HIL_WIRE_DATA2, |
| HIL_WIRE_DATA1, |
| HIL_WIRE_DATA0, |
| HIL_WIRE_PARITY, |
| HIL_WIRE_STOP |
| }; |
| |
| /* HP documentation uses these bit positions to refer to commands; |
| * we will call these "packets". |
| */ |
| enum hil_pkt_bitpos { |
| HIL_PKT_CMD = 0x00000800, |
| HIL_PKT_ADDR2 = 0x00000400, |
| HIL_PKT_ADDR1 = 0x00000200, |
| HIL_PKT_ADDR0 = 0x00000100, |
| HIL_PKT_ADDR_MASK = 0x00000700, |
| HIL_PKT_ADDR_SHIFT = 8, |
| HIL_PKT_DATA7 = 0x00000080, |
| HIL_PKT_DATA6 = 0x00000040, |
| HIL_PKT_DATA5 = 0x00000020, |
| HIL_PKT_DATA4 = 0x00000010, |
| HIL_PKT_DATA3 = 0x00000008, |
| HIL_PKT_DATA2 = 0x00000004, |
| HIL_PKT_DATA1 = 0x00000002, |
| HIL_PKT_DATA0 = 0x00000001, |
| HIL_PKT_DATA_MASK = 0x000000FF, |
| HIL_PKT_DATA_SHIFT = 0 |
| }; |
| |
| /* The HIL MLC also has several error/status/control bits. We extend the |
| * "packet" to include these when direct access to the MLC is available, |
| * or emulate them in cases where they are not available. |
| * |
| * This way the device driver knows that the underlying MLC driver |
| * has had to deal with loop errors. |
| */ |
| enum hil_error_bitpos { |
| HIL_ERR_OB = 0x00000800, /* MLC is busy sending an auto-poll, |
| or we have filled up the output |
| buffer and must wait. */ |
| HIL_ERR_INT = 0x00010000, /* A normal interrupt has occurred. */ |
| HIL_ERR_NMI = 0x00020000, /* An NMI has occurred. */ |
| HIL_ERR_LERR = 0x00040000, /* A poll didn't come back. */ |
| HIL_ERR_PERR = 0x01000000, /* There was a Parity Error. */ |
| HIL_ERR_FERR = 0x02000000, /* There was a Framing Error. */ |
| HIL_ERR_FOF = 0x04000000 /* Input FIFO Overflowed. */ |
| }; |
| |
| enum hil_control_bitpos { |
| HIL_CTRL_TEST = 0x00010000, |
| HIL_CTRL_IPF = 0x00040000, |
| HIL_CTRL_APE = 0x02000000 |
| }; |
| |
| /* Bits 30,31 are unused, we use them to control write behavior. */ |
| #define HIL_DO_ALTER_CTRL 0x40000000 /* Write MSW of packet to control |
| before writing LSW to loop */ |
| #define HIL_CTRL_ONLY 0xc0000000 /* *Only* alter the control registers */ |
| |
| /* This gives us a 32-bit "packet" |
| */ |
| typedef u32 hil_packet; |
| |
| |
| /* HIL Loop commands |
| */ |
| enum hil_command { |
| HIL_CMD_IFC = 0x00, /* Interface Clear */ |
| HIL_CMD_EPT = 0x01, /* Enter Pass-Thru Mode */ |
| HIL_CMD_ELB = 0x02, /* Enter Loop-Back Mode */ |
| HIL_CMD_IDD = 0x03, /* Identify and Describe */ |
| HIL_CMD_DSR = 0x04, /* Device Soft Reset */ |
| HIL_CMD_PST = 0x05, /* Perform Self Test */ |
| HIL_CMD_RRG = 0x06, /* Read Register */ |
| HIL_CMD_WRG = 0x07, /* Write Register */ |
| HIL_CMD_ACF = 0x08, /* Auto Configure */ |
| HIL_CMDID_ACF = 0x07, /* Auto Configure bits with incremented ID */ |
| HIL_CMD_POL = 0x10, /* Poll */ |
| HIL_CMDCT_POL = 0x0f, /* Poll command bits with item count */ |
| HIL_CMD_RPL = 0x20, /* RePoll */ |
| HIL_CMDCT_RPL = 0x0f, /* RePoll command bits with item count */ |
| HIL_CMD_RNM = 0x30, /* Report Name */ |
| HIL_CMD_RST = 0x31, /* Report Status */ |
| HIL_CMD_EXD = 0x32, /* Extended Describe */ |
| HIL_CMD_RSC = 0x33, /* Report Security Code */ |
| |
| /* 0x34 to 0x3c reserved for future use */ |
| |
| HIL_CMD_DKA = 0x3d, /* Disable Keyswitch Autorepeat */ |
| HIL_CMD_EK1 = 0x3e, /* Enable Keyswitch Autorepeat 1 */ |
| HIL_CMD_EK2 = 0x3f, /* Enable Keyswitch Autorepeat 2 */ |
| HIL_CMD_PR1 = 0x40, /* Prompt1 */ |
| HIL_CMD_PR2 = 0x41, /* Prompt2 */ |
| HIL_CMD_PR3 = 0x42, /* Prompt3 */ |
| HIL_CMD_PR4 = 0x43, /* Prompt4 */ |
| HIL_CMD_PR5 = 0x44, /* Prompt5 */ |
| HIL_CMD_PR6 = 0x45, /* Prompt6 */ |
| HIL_CMD_PR7 = 0x46, /* Prompt7 */ |
| HIL_CMD_PRM = 0x47, /* Prompt (General Purpose) */ |
| HIL_CMD_AK1 = 0x48, /* Acknowledge1 */ |
| HIL_CMD_AK2 = 0x49, /* Acknowledge2 */ |
| HIL_CMD_AK3 = 0x4a, /* Acknowledge3 */ |
| HIL_CMD_AK4 = 0x4b, /* Acknowledge4 */ |
| HIL_CMD_AK5 = 0x4c, /* Acknowledge5 */ |
| HIL_CMD_AK6 = 0x4d, /* Acknowledge6 */ |
| HIL_CMD_AK7 = 0x4e, /* Acknowledge7 */ |
| HIL_CMD_ACK = 0x4f, /* Acknowledge (General Purpose) */ |
| |
| /* 0x50 to 0x78 reserved for future use */ |
| /* 0x80 to 0xEF device-specific commands */ |
| /* 0xf0 to 0xf9 reserved for future use */ |
| |
| HIL_CMD_RIO = 0xfa, /* Register I/O Error */ |
| HIL_CMD_SHR = 0xfb, /* System Hard Reset */ |
| HIL_CMD_TER = 0xfc, /* Transmission Error */ |
| HIL_CMD_CAE = 0xfd, /* Configuration Address Error */ |
| HIL_CMD_DHR = 0xfe, /* Device Hard Reset */ |
| |
| /* 0xff is prohibited from use. */ |
| }; |
| |
| |
| /* |
| * Response "records" to HIL commands |
| */ |
| |
| /* Device ID byte |
| */ |
| #define HIL_IDD_DID_TYPE_MASK 0xe0 /* Primary type bits */ |
| #define HIL_IDD_DID_TYPE_KB_INTEGRAL 0xa0 /* Integral keyboard */ |
| #define HIL_IDD_DID_TYPE_KB_ITF 0xc0 /* ITD keyboard */ |
| #define HIL_IDD_DID_TYPE_KB_RSVD 0xe0 /* Reserved keyboard type */ |
| #define HIL_IDD_DID_TYPE_KB_LANG_MASK 0x1f /* Keyboard locale bits */ |
| #define HIL_IDD_DID_KBLANG_USE_ESD 0x00 /* Use ESD Locale instead */ |
| #define HIL_IDD_DID_TYPE_ABS 0x80 /* Absolute Positioners */ |
| #define HIL_IDD_DID_ABS_RSVD1_MASK 0xf8 /* Reserved */ |
| #define HIL_IDD_DID_ABS_RSVD1 0x98 |
| #define HIL_IDD_DID_ABS_TABLET_MASK 0xf8 /* Tablets and digitizers */ |
| #define HIL_IDD_DID_ABS_TABLET 0x90 |
| #define HIL_IDD_DID_ABS_TSCREEN_MASK 0xfc /* Touch screens */ |
| #define HIL_IDD_DID_ABS_TSCREEN 0x8c |
| #define HIL_IDD_DID_ABS_RSVD2_MASK 0xfc /* Reserved */ |
| #define HIL_IDD_DID_ABS_RSVD2 0x88 |
| #define HIL_IDD_DID_ABS_RSVD3_MASK 0xfc /* Reserved */ |
| #define HIL_IDD_DID_ABS_RSVD3 0x80 |
| #define HIL_IDD_DID_TYPE_REL 0x60 /* Relative Positioners */ |
| #define HIL_IDD_DID_REL_RSVD1_MASK 0xf0 /* Reserved */ |
| #define HIL_IDD_DID_REL_RSVD1 0x70 |
| #define HIL_IDD_DID_REL_RSVD2_MASK 0xfc /* Reserved */ |
| #define HIL_IDD_DID_REL_RSVD2 0x6c |
| #define HIL_IDD_DID_REL_MOUSE_MASK 0xfc /* Mouse */ |
| #define HIL_IDD_DID_REL_MOUSE 0x68 |
| #define HIL_IDD_DID_REL_QUAD_MASK 0xf8 /* Other Quadrature Devices */ |
| #define HIL_IDD_DID_REL_QUAD 0x60 |
| #define HIL_IDD_DID_TYPE_CHAR 0x40 /* Character Entry */ |
| #define HIL_IDD_DID_CHAR_BARCODE_MASK 0xfc /* Barcode Reader */ |
| #define HIL_IDD_DID_CHAR_BARCODE 0x5c |
| #define HIL_IDD_DID_CHAR_RSVD1_MASK 0xfc /* Reserved */ |
| #define HIL_IDD_DID_CHAR_RSVD1 0x58 |
| #define HIL_IDD_DID_CHAR_RSVD2_MASK 0xf8 /* Reserved */ |
| #define HIL_IDD_DID_CHAR_RSVD2 0x50 |
| #define HIL_IDD_DID_CHAR_RSVD3_MASK 0xf0 /* Reserved */ |
| #define HIL_IDD_DID_CHAR_RSVD3 0x40 |
| #define HIL_IDD_DID_TYPE_OTHER 0x20 /* Miscellaneous */ |
| #define HIL_IDD_DID_OTHER_RSVD1_MASK 0xf0 /* Reserved */ |
| #define HIL_IDD_DID_OTHER_RSVD1 0x30 |
| #define HIL_IDD_DID_OTHER_BARCODE_MASK 0xfc /* Tone Generator */ |
| #define HIL_IDD_DID_OTHER_BARCODE 0x2c |
| #define HIL_IDD_DID_OTHER_RSVD2_MASK 0xfc /* Reserved */ |
| #define HIL_IDD_DID_OTHER_RSVD2 0x28 |
| #define HIL_IDD_DID_OTHER_RSVD3_MASK 0xf8 /* Reserved */ |
| #define HIL_IDD_DID_OTHER_RSVD3 0x20 |
| #define HIL_IDD_DID_TYPE_KEYPAD 0x00 /* Vectra Keyboard */ |
| |
| /* IDD record header |
| */ |
| #define HIL_IDD_HEADER_AXSET_MASK 0x03 /* Number of axis in a set */ |
| #define HIL_IDD_HEADER_RSC 0x04 /* Supports RSC command */ |
| #define HIL_IDD_HEADER_EXD 0x08 /* Supports EXD command */ |
| #define HIL_IDD_HEADER_IOD 0x10 /* IOD byte to follow */ |
| #define HIL_IDD_HEADER_16BIT 0x20 /* 16 (vs. 8) bit resolution */ |
| #define HIL_IDD_HEADER_ABS 0x40 /* Reports Absolute Position */ |
| #define HIL_IDD_HEADER_2X_AXIS 0x80 /* Two sets of 1-3 axis */ |
| |
| /* I/O Descriptor |
| */ |
| #define HIL_IDD_IOD_NBUTTON_MASK 0x07 /* Number of buttons */ |
| #define HIL_IDD_IOD_PROXIMITY 0x08 /* Proximity in/out events */ |
| #define HIL_IDD_IOD_PROMPT_MASK 0x70 /* Number of prompts/acks */ |
| #define HIL_IDD_IOD_PROMPT_SHIFT 4 |
| #define HIL_IDD_IOD_PROMPT 0x80 /* Generic prompt/ack */ |
| |
| #define HIL_IDD_NUM_AXES_PER_SET(header_packet) \ |
| ((header_packet) & HIL_IDD_HEADER_AXSET_MASK) |
| |
| #define HIL_IDD_NUM_AXSETS(header_packet) \ |
| (2 - !((header_packet) & HIL_IDD_HEADER_2X_AXIS)) |
| |
| #define HIL_IDD_LEN(header_packet) \ |
| ((4 - !(header_packet & HIL_IDD_HEADER_IOD) - \ |
| 2 * !(HIL_IDD_NUM_AXES_PER_SET(header_packet))) + \ |
| 2 * HIL_IDD_NUM_AXES_PER_SET(header_packet) * \ |
| !!((header_packet) & HIL_IDD_HEADER_ABS)) |
| |
| /* The following HIL_IDD_* macros assume you have an array of |
| * packets and/or unpacked 8-bit data in the order that they |
| * were received. |
| */ |
| |
| #define HIL_IDD_AXIS_COUNTS_PER_M(header_ptr) \ |
| (!(HIL_IDD_NUM_AXSETS(*(header_ptr))) ? -1 : \ |
| (((*(header_ptr + 1) & HIL_PKT_DATA_MASK) + \ |
| ((*(header_ptr + 2) & HIL_PKT_DATA_MASK)) << 8) \ |
| * ((*(header_ptr) & HIL_IDD_HEADER_16BIT) ? 100 : 1))) |
| |
| #define HIL_IDD_AXIS_MAX(header_ptr, __axnum) \ |
| ((!(*(header_ptr) & HIL_IDD_HEADER_ABS) || \ |
| (HIL_IDD_NUM_AXES_PER_SET(*(header_ptr)) <= __axnum)) ? 0 : \ |
| ((HIL_PKT_DATA_MASK & *((header_ptr) + 3 + 2 * __axnum)) + \ |
| ((HIL_PKT_DATA_MASK & *((header_ptr) + 4 + 2 * __axnum)) << 8))) |
| |
| #define HIL_IDD_IOD(header_ptr) \ |
| (*(header_ptr + HIL_IDD_LEN((*header_ptr)) - 1)) |
| |
| #define HIL_IDD_HAS_GEN_PROMPT(header_ptr) \ |
| ((*header_ptr & HIL_IDD_HEADER_IOD) && \ |
| (HIL_IDD_IOD(header_ptr) & HIL_IDD_IOD_PROMPT)) |
| |
| #define HIL_IDD_HAS_GEN_PROXIMITY(header_ptr) \ |
| ((*header_ptr & HIL_IDD_HEADER_IOD) && \ |
| (HIL_IDD_IOD(header_ptr) & HIL_IDD_IOD_PROXIMITY)) |
| |
| #define HIL_IDD_NUM_BUTTONS(header_ptr) \ |
| ((*header_ptr & HIL_IDD_HEADER_IOD) ? \ |
| (HIL_IDD_IOD(header_ptr) & HIL_IDD_IOD_NBUTTON_MASK) : 0) |
| |
| #define HIL_IDD_NUM_PROMPTS(header_ptr) \ |
| ((*header_ptr & HIL_IDD_HEADER_IOD) ? \ |
| ((HIL_IDD_IOD(header_ptr) & HIL_IDD_IOD_NPROMPT_MASK) \ |
| >> HIL_IDD_IOD_PROMPT_SHIFT) : 0) |
| |
| /* The response to HIL EXD commands -- the "extended describe record" */ |
| #define HIL_EXD_HEADER_WRG 0x03 /* Supports type2 WRG */ |
| #define HIL_EXD_HEADER_WRG_TYPE1 0x01 /* Supports type1 WRG */ |
| #define HIL_EXD_HEADER_WRG_TYPE2 0x02 /* Supports type2 WRG */ |
| #define HIL_EXD_HEADER_RRG 0x04 /* Supports RRG command */ |
| #define HIL_EXD_HEADER_RNM 0x10 /* Supports RNM command */ |
| #define HIL_EXD_HEADER_RST 0x20 /* Supports RST command */ |
| #define HIL_EXD_HEADER_LOCALE 0x40 /* Contains locale code */ |
| |
| #define HIL_EXD_NUM_RRG(header_ptr) \ |
| ((*header_ptr & HIL_EXD_HEADER_RRG) ? \ |
| (*(header_ptr + 1) & HIL_PKT_DATA_MASK) : 0) |
| |
| #define HIL_EXD_NUM_WWG(header_ptr) \ |
| ((*header_ptr & HIL_EXD_HEADER_WRG) ? \ |
| (*(header_ptr + 2 - !(*header_ptr & HIL_EXD_HEADER_RRG)) & \ |
| HIL_PKT_DATA_MASK) : 0) |
| |
| #define HIL_EXD_LEN(header_ptr) \ |
| (!!(*header_ptr & HIL_EXD_HEADER_RRG) + \ |
| !!(*header_ptr & HIL_EXD_HEADER_WRG) + \ |
| !!(*header_ptr & HIL_EXD_HEADER_LOCALE) + \ |
| 2 * !!(*header_ptr & HIL_EXD_HEADER_WRG_TYPE2) + 1) |
| |
| #define HIL_EXD_LOCALE(header_ptr) \ |
| (!(*header_ptr & HIL_EXD_HEADER_LOCALE) ? -1 : \ |
| (*(header_ptr + HIL_EXD_LEN(header_ptr) - 1) & HIL_PKT_DATA_MASK)) |
| |
| #define HIL_EXD_WRG_TYPE2_LEN(header_ptr) \ |
| (!(*header_ptr & HIL_EXD_HEADER_WRG_TYPE2) ? -1 : \ |
| (*(header_ptr + HIL_EXD_LEN(header_ptr) - 2 - \ |
| !!(*header_ptr & HIL_EXD_HEADER_LOCALE)) & HIL_PKT_DATA_MASK) + \ |
| ((*(header_ptr + HIL_EXD_LEN(header_ptr) - 1 - \ |
| !!(*header_ptr & HIL_EXD_HEADER_LOCALE)) & HIL_PKT_DATA_MASK) << 8)) |
| |
| /* Device locale codes. */ |
| |
| /* Last defined locale code. Everything above this is "Reserved", |
| and note that this same table applies to the Device ID Byte where |
| keyboards may have a nationality code which is only 5 bits. */ |
| #define HIL_LOCALE_MAX 0x1f |
| |
| /* Map to hopefully useful strings. I was trying to make these look |
| like locale.aliases strings do; maybe that isn't the right table to |
| emulate. In either case, I didn't have much to work on. */ |
| #define HIL_LOCALE_MAP \ |
| "", /* 0x00 Reserved */ \ |
| "", /* 0x01 Reserved */ \ |
| "", /* 0x02 Reserved */ \ |
| "swiss.french", /* 0x03 Swiss/French */ \ |
| "portuguese", /* 0x04 Portuguese */ \ |
| "arabic", /* 0x05 Arabic */ \ |
| "hebrew", /* 0x06 Hebrew */ \ |
| "english.canadian", /* 0x07 Canadian English */ \ |
| "turkish", /* 0x08 Turkish */ \ |
| "greek", /* 0x09 Greek */ \ |
| "thai", /* 0x0a Thai (Thailand) */ \ |
| "italian", /* 0x0b Italian */ \ |
| "korean", /* 0x0c Hangul (Korea) */ \ |
| "dutch", /* 0x0d Dutch */ \ |
| "swedish", /* 0x0e Swedish */ \ |
| "german", /* 0x0f German */ \ |
| "chinese", /* 0x10 Chinese-PRC */ \ |
| "chinese", /* 0x11 Chinese-ROC */ \ |
| "swiss.french", /* 0x12 Swiss/French II */ \ |
| "spanish", /* 0x13 Spanish */ \ |
| "swiss.german", /* 0x14 Swiss/German II */ \ |
| "flemish", /* 0x15 Belgian (Flemish) */ \ |
| "finnish", /* 0x16 Finnish */ \ |
| "english.uk", /* 0x17 United Kingdom */ \ |
| "french.canadian", /* 0x18 French/Canadian */ \ |
| "swiss.german", /* 0x19 Swiss/German */ \ |
| "norwegian", /* 0x1a Norwegian */ \ |
| "french", /* 0x1b French */ \ |
| "danish", /* 0x1c Danish */ \ |
| "japanese", /* 0x1d Katakana */ \ |
| "spanish", /* 0x1e Latin American/Spanish*/\ |
| "english.us" /* 0x1f United States */ \ |
| |
| |
| /* HIL keycodes */ |
| #define HIL_KEYCODES_SET1_TBLSIZE 128 |
| #define HIL_KEYCODES_SET1 \ |
| KEY_5, KEY_RESERVED, KEY_RIGHTALT, KEY_LEFTALT, \ |
| KEY_RIGHTSHIFT, KEY_LEFTSHIFT, KEY_LEFTCTRL, KEY_SYSRQ, \ |
| KEY_KP4, KEY_KP8, KEY_KP5, KEY_KP9, \ |
| KEY_KP6, KEY_KP7, KEY_KPCOMMA, KEY_KPENTER, \ |
| KEY_KP1, KEY_KPSLASH, KEY_KP2, KEY_KPPLUS, \ |
| KEY_KP3, KEY_KPASTERISK, KEY_KP0, KEY_KPMINUS, \ |
| KEY_B, KEY_V, KEY_C, KEY_X, \ |
| KEY_Z, KEY_RESERVED, KEY_RESERVED, KEY_ESC, \ |
| KEY_6, KEY_F10, KEY_3, KEY_F11, \ |
| KEY_KPDOT, KEY_F9, KEY_TAB /*KP*/, KEY_F12, \ |
| KEY_H, KEY_G, KEY_F, KEY_D, \ |
| KEY_S, KEY_A, KEY_RESERVED, KEY_CAPSLOCK, \ |
| KEY_U, KEY_Y, KEY_T, KEY_R, \ |
| KEY_E, KEY_W, KEY_Q, KEY_TAB, \ |
| KEY_7, KEY_6, KEY_5, KEY_4, \ |
| KEY_3, KEY_2, KEY_1, KEY_GRAVE, \ |
| KEY_F13, KEY_F14, KEY_F15, KEY_F16, \ |
| KEY_F17, KEY_F18, KEY_F19, KEY_F20, \ |
| KEY_MENU, KEY_F4, KEY_F3, KEY_F2, \ |
| KEY_F1, KEY_VOLUMEUP, KEY_STOP, KEY_SENDFILE, \ |
| KEY_SYSRQ, KEY_F5, KEY_F6, KEY_F7, \ |
| KEY_F8, KEY_VOLUMEDOWN, KEY_DEL_EOL, KEY_DEL_EOS, \ |
| KEY_8, KEY_9, KEY_0, KEY_MINUS, \ |
| KEY_EQUAL, KEY_BACKSPACE, KEY_INS_LINE, KEY_DEL_LINE, \ |
| KEY_I, KEY_O, KEY_P, KEY_LEFTBRACE, \ |
| KEY_RIGHTBRACE, KEY_BACKSLASH, KEY_INSERT, KEY_DELETE, \ |
| KEY_J, KEY_K, KEY_L, KEY_SEMICOLON, \ |
| KEY_APOSTROPHE, KEY_ENTER, KEY_HOME, KEY_PAGEUP, \ |
| KEY_M, KEY_COMMA, KEY_DOT, KEY_SLASH, \ |
| KEY_BACKSLASH, KEY_SELECT, KEY_102ND, KEY_PAGEDOWN, \ |
| KEY_N, KEY_SPACE, KEY_NEXT, KEY_RESERVED, \ |
| KEY_LEFT, KEY_DOWN, KEY_UP, KEY_RIGHT |
| |
| |
| #define HIL_KEYCODES_SET3_TBLSIZE 128 |
| #define HIL_KEYCODES_SET3 \ |
| KEY_RESERVED, KEY_ESC, KEY_1, KEY_2, \ |
| KEY_3, KEY_4, KEY_5, KEY_6, \ |
| KEY_7, KEY_8, KEY_9, KEY_0, \ |
| KEY_MINUS, KEY_EQUAL, KEY_BACKSPACE, KEY_TAB, \ |
| KEY_Q, KEY_W, KEY_E, KEY_R, \ |
| KEY_T, KEY_Y, KEY_U, KEY_I, \ |
| KEY_O, KEY_P, KEY_LEFTBRACE, KEY_RIGHTBRACE, \ |
| KEY_ENTER, KEY_LEFTCTRL, KEY_A, KEY_S, \ |
| KEY_D, KEY_F, KEY_G, KEY_H, \ |
| KEY_J, KEY_K, KEY_L, KEY_SEMICOLON, \ |
| KEY_APOSTROPHE,KEY_GRAVE, KEY_LEFTSHIFT, KEY_BACKSLASH, \ |
| KEY_Z, KEY_X, KEY_C, KEY_V, \ |
| KEY_B, KEY_N, KEY_M, KEY_COMMA, \ |
| KEY_DOT, KEY_SLASH, KEY_RIGHTSHIFT, KEY_KPASTERISK, \ |
| KEY_LEFTALT, KEY_SPACE, KEY_CAPSLOCK, KEY_F1, \ |
| KEY_F2, KEY_F3, KEY_F4, KEY_F5, \ |
| KEY_F6, KEY_F7, KEY_F8, KEY_F9, \ |
| KEY_F10, KEY_NUMLOCK, KEY_SCROLLLOCK, KEY_KP7, \ |
| KEY_KP8, KEY_KP9, KEY_KPMINUS, KEY_KP4, \ |
| KEY_KP5, KEY_KP6, KEY_KPPLUS, KEY_KP1, \ |
| KEY_KP2, KEY_KP3, KEY_KP0, KEY_KPDOT, \ |
| KEY_SYSRQ, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, \ |
| KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, \ |
| KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, \ |
| KEY_UP, KEY_LEFT, KEY_DOWN, KEY_RIGHT, \ |
| KEY_HOME, KEY_PAGEUP, KEY_END, KEY_PAGEDOWN, \ |
| KEY_INSERT, KEY_DELETE, KEY_102ND, KEY_RESERVED, \ |
| KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, \ |
| KEY_F1, KEY_F2, KEY_F3, KEY_F4, \ |
| KEY_F5, KEY_F6, KEY_F7, KEY_F8, \ |
| KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, \ |
| KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED |
| |
| |
| /* Response to POL command, the "poll record header" */ |
| |
| #define HIL_POL_NUM_AXES_MASK 0x03 /* Number of axis reported */ |
| #define HIL_POL_CTS 0x04 /* Device ready to receive data */ |
| #define HIL_POL_STATUS_PENDING 0x08 /* Device has status to report */ |
| #define HIL_POL_CHARTYPE_MASK 0x70 /* Type of character data to follow */ |
| #define HIL_POL_CHARTYPE_NONE 0x00 /* No character data to follow */ |
| #define HIL_POL_CHARTYPE_RSVD1 0x10 /* Reserved Set 1 */ |
| #define HIL_POL_CHARTYPE_ASCII 0x20 /* U.S. ASCII */ |
| #define HIL_POL_CHARTYPE_BINARY 0x30 /* Binary data */ |
| #define HIL_POL_CHARTYPE_SET1 0x40 /* Keycode Set 1 */ |
| #define HIL_POL_CHARTYPE_RSVD2 0x50 /* Reserved Set 2 */ |
| #define HIL_POL_CHARTYPE_SET2 0x60 /* Keycode Set 2 */ |
| #define HIL_POL_CHARTYPE_SET3 0x70 /* Keycode Set 3 */ |
| #define HIL_POL_AXIS_ALT 0x80 /* Data is from axis set 2 */ |
| |
| |
| #endif /* _HIL_H_ */ |
