blob: 84630e56acd75fcad3542596509ba7c027dcf28f [file] [log] [blame]
/*
* Copyright 2013 Maxime Ripard
*
* Maxime Ripard <maxime.ripard@free-electrons.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun6i-a31.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "WITS A31 Colombus Evaluation Board";
compatible = "wits,colombus", "allwinner,sun6i-a31";
chosen {
bootargs = "earlyprintk console=ttyS0,115200";
};
soc@01c00000 {
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>;
vmmc-supply = <&reg_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
cd-inverted;
status = "okay";
};
usbphy: phy@01c19400 {
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci1: usb@01c1b000 {
status = "okay";
};
pio: pinctrl@01c20800 {
mmc0_pins_a: mmc0@0 {
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
mmc0_cd_pin_colombus: mmc0_cd_pin@0 {
allwinner,pins = "PA8";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
usb2_vbus_pin_colombus: usb2_vbus_pin@0 {
allwinner,pins = "PH24";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "fail";
};
i2c1: i2c@01c2b000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
i2c2: i2c@01c2b400 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
};
reg_usb2_vbus: usb2-vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb2_vbus_pin_colombus>;
gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>;
status = "okay";
};
};