iwlwifi: mvm: always init rs with 20mhz bandwidth rates
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c b/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
index 8aed40a..08de822 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
@@ -2682,6 +2682,10 @@
/* enable beacon filtering */
WARN_ON(iwl_mvm_enable_beacon_filter(mvm, vif, 0));
+
+ iwl_mvm_rs_rate_init(mvm, sta, mvmvif->phy_ctxt->channel->band,
+ false);
+
ret = 0;
} else if (old_state == IEEE80211_STA_AUTHORIZED &&
new_state == IEEE80211_STA_ASSOC) {
diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/rs.c b/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
index 60abb00..47f4c7a 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
@@ -2684,7 +2684,8 @@
struct ieee80211_sta *sta,
struct iwl_lq_sta *lq_sta,
enum nl80211_band band,
- struct rs_rate *rate)
+ struct rs_rate *rate,
+ bool init)
{
int i, nentries;
unsigned long active_rate;
@@ -2738,14 +2739,25 @@
*/
if (sta->vht_cap.vht_supported &&
best_rssi > IWL_RS_LOW_RSSI_THRESHOLD) {
- switch (sta->bandwidth) {
- case IEEE80211_STA_RX_BW_160:
- case IEEE80211_STA_RX_BW_80:
- case IEEE80211_STA_RX_BW_40:
+ /*
+ * In AP mode, when a new station associates, rs is initialized
+ * immediately upon association completion, before the phy
+ * context is updated with the association parameters, so the
+ * sta bandwidth might be wider than the phy context allows.
+ * To avoid this issue, always initialize rs with 20mhz
+ * bandwidth rate, and after authorization, when the phy context
+ * is already up-to-date, re-init rs with the correct bw.
+ */
+ u32 bw = init ? RATE_MCS_CHAN_WIDTH_20 : rs_bw_from_sta_bw(sta);
+
+ switch (bw) {
+ case RATE_MCS_CHAN_WIDTH_40:
+ case RATE_MCS_CHAN_WIDTH_80:
+ case RATE_MCS_CHAN_WIDTH_160:
initial_rates = rs_optimal_rates_vht;
nentries = ARRAY_SIZE(rs_optimal_rates_vht);
break;
- case IEEE80211_STA_RX_BW_20:
+ case RATE_MCS_CHAN_WIDTH_20:
initial_rates = rs_optimal_rates_vht_20mhz;
nentries = ARRAY_SIZE(rs_optimal_rates_vht_20mhz);
break;
@@ -2756,7 +2768,7 @@
active_rate = lq_sta->active_siso_rate;
rate->type = LQ_VHT_SISO;
- rate->bw = rs_bw_from_sta_bw(sta);
+ rate->bw = bw;
} else if (sta->ht_cap.ht_supported &&
best_rssi > IWL_RS_LOW_RSSI_THRESHOLD) {
initial_rates = rs_optimal_rates_ht;
@@ -2839,7 +2851,7 @@
tbl = &(lq_sta->lq_info[active_tbl]);
rate = &tbl->rate;
- rs_get_initial_rate(mvm, sta, lq_sta, band, rate);
+ rs_get_initial_rate(mvm, sta, lq_sta, band, rate, init);
rs_init_optimal_rate(mvm, sta, lq_sta);
WARN_ONCE(rate->ant != ANT_A && rate->ant != ANT_B,
