blob: 17b4a94916d6d87c9d1fb9f42da49522594b5e2d [file] [log] [blame]
Device Tree Clock bindings for the Zynq 7000 EPP
The Zynq EPP has several different clk providers, each with there own bindings.
The purpose of this document is to document their usage.
See clock_bindings.txt for more information on the generic clock bindings.
See Chapter 25 of Zynq TRM for more information about Zynq clocks.
== Clock Controller ==
The clock controller is a logical abstraction of Zynq's clock tree. It reads
required input clock frequencies from the devicetree and acts as clock provider
for all clock consumers of PS clocks.
Required properties:
- #clock-cells : Must be 1
- compatible : "xlnx,ps7-clkc"
- ps-clk-frequency : Frequency of the oscillator providing ps_clk in HZ
(usually 33 MHz oscillators are used for Zynq platforms)
- clock-output-names : List of strings used to name the clock outputs. Shall be
a list of the outputs given below.
Optional properties:
- clocks : as described in the clock bindings
- clock-names : as described in the clock bindings
- fclk-enable : Bit mask to enable FCLKs statically at boot time.
Bit [0..3] correspond to FCLK0..FCLK3. The corresponding
FCLK will only be enabled if it is actually running at
boot time.
Clock inputs:
The following strings are optional parameters to the 'clock-names' property in
order to provide an optional (E)MIO clock source.
- swdt_ext_clk
- gem0_emio_clk
- gem1_emio_clk
- mio_clk_XX # with XX = 00..53
...
Clock outputs:
0: armpll
1: ddrpll
2: iopll
3: cpu_6or4x
4: cpu_3or2x
5: cpu_2x
6: cpu_1x
7: ddr2x
8: ddr3x
9: dci
10: lqspi
11: smc
12: pcap
13: gem0
14: gem1
15: fclk0
16: fclk1
17: fclk2
18: fclk3
19: can0
20: can1
21: sdio0
22: sdio1
23: uart0
24: uart1
25: spi0
26: spi1
27: dma
28: usb0_aper
29: usb1_aper
30: gem0_aper
31: gem1_aper
32: sdio0_aper
33: sdio1_aper
34: spi0_aper
35: spi1_aper
36: can0_aper
37: can1_aper
38: i2c0_aper
39: i2c1_aper
40: uart0_aper
41: uart1_aper
42: gpio_aper
43: lqspi_aper
44: smc_aper
45: swdt
46: dbg_trc
47: dbg_apb
Example:
clkc: clkc {
#clock-cells = <1>;
compatible = "xlnx,ps7-clkc";
ps-clk-frequency = <33333333>;
clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
"cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
"dci", "lqspi", "smc", "pcap", "gem0", "gem1",
"fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
"sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1",
"dma", "usb0_aper", "usb1_aper", "gem0_aper",
"gem1_aper", "sdio0_aper", "sdio1_aper",
"spi0_aper", "spi1_aper", "can0_aper", "can1_aper",
"i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper",
"gpio_aper", "lqspi_aper", "smc_aper", "swdt",
"dbg_trc", "dbg_apb";
# optional props
clocks = <&clkc 16>, <&clk_foo>;
clock-names = "gem1_emio_clk", "can_mio_clk_23";
};