blob: 6a34114bec294b7c3f57a48024f3ca3d71cc37ab [file] [log] [blame]
/*
* Copyright 2013 Crystalfontz America, Inc.
* Free Electrons
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/*
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10055 Board";
compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
apb@80000000 {
apbh@80000000 {
pinctrl@80018000 {
spi2_pins_cfa10055: spi2-cfa10055@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SCK__GPIO_2_16
MX28_PAD_SSP2_MOSI__GPIO_2_17
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_8mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D00__LCD_D0
MX28_PAD_LCD_D01__LCD_D1
MX28_PAD_LCD_D02__LCD_D2
MX28_PAD_LCD_D03__LCD_D3
MX28_PAD_LCD_D04__LCD_D4
MX28_PAD_LCD_D05__LCD_D5
MX28_PAD_LCD_D06__LCD_D6
MX28_PAD_LCD_D07__LCD_D7
MX28_PAD_LCD_D08__LCD_D8
MX28_PAD_LCD_D09__LCD_D9
MX28_PAD_LCD_D10__LCD_D10
MX28_PAD_LCD_D11__LCD_D11
MX28_PAD_LCD_D12__LCD_D12
MX28_PAD_LCD_D13__LCD_D13
MX28_PAD_LCD_D14__LCD_D14
MX28_PAD_LCD_D15__LCD_D15
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_18bit_pins_cfa10055
&lcdif_pins_cfa10055
&lcdif_pins_cfa10055_pullup>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <18>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <9216000>;
hactive = <320>;
vactive = <480>;
hback-porch = <2>;
hfront-porch = <2>;
vback-porch = <2>;
vfront-porch = <2>;
hsync-len = <15>;
vsync-len = <15>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
};
apbx@80040000 {
lradc@80050000 {
fsl,lradc-touchscreen-wires = <4>;
status = "okay";
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pins_b>;
status = "okay";
};
};
};
spi2 {
compatible = "spi-gpio";
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_cfa10055>;
status = "okay";
gpio-sck = <&gpio2 16 0>;
gpio-mosi = <&gpio2 17 0>;
gpio-miso = <&gpio2 18 0>;
cs-gpios = <&gpio3 5 0>;
num-chipselects = <1>;
#address-cells = <1>;
#size-cells = <0>;
hx8357: hx8357@0 {
compatible = "himax,hx8357b", "himax,hx8357";
reg = <0>;
spi-max-frequency = <100000>;
spi-cpol;
spi-cpha;
gpios-reset = <&gpio3 30 0>;
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
};
};