blob: d6fae13ff0628bef56a69d671a9a684fa7ab2280 [file] [log] [blame]
* Synopsys Designware PCIe interface
Required properties:
- compatible: should contain "snps,dw-pcie" to identify the
core, plus an identifier for the specific instance, such
as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie".
- reg: base addresses and lengths of the pcie controller,
the phy controller, additional register for the phy controller.
- interrupts: interrupt values for level interrupt,
pulse interrupt, special interrupt.
- clocks: from common clock binding: handle to pci clock.
- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
- #address-cells: set to <3>
- #size-cells: set to <2>
- device_type: set to "pci"
- ranges: ranges for the PCI memory and I/O regions
- #interrupt-cells: set to <1>
- interrupt-map-mask and interrupt-map: standard PCI properties
to define the mapping of the PCIe interface to interrupt
numbers.
- num-lanes: number of lanes to use
Optional properties:
- reset-gpio: gpio pin number of power good signal
Optional properties for fsl,imx6q-pcie
- power-on-gpio: gpio pin number of power-enable signal
- wake-up-gpio: gpio pin number of incoming wakeup signal
- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
Example:
SoC specific DT Entry:
pcie@290000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x290000 0x1000
0x270000 0x1000
0x271000 0x40>;
interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
clocks = <&clock 28>, <&clock 27>;
clock-names = "pcie", "pcie_bus";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */
0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0x0 0 &gic 53>;
num-lanes = <4>;
};
pcie@2a0000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x2a0000 0x1000
0x272000 0x1000
0x271040 0x40>;
interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
clocks = <&clock 29>, <&clock 27>;
clock-names = "pcie", "pcie_bus";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */
0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0x0 0 &gic 56>;
num-lanes = <4>;
};
Board specific DT Entry:
pcie@290000 {
reset-gpio = <&pin_ctrl 5 0>;
};
pcie@2a0000 {
reset-gpio = <&pin_ctrl 22 0>;
};