phy: brcm-sata: Correct MDIO operations for 40nm platforms
The logic to write to MDIO registers on 40nm platforms was wrong
because it would use the port number as an offset from the base address
rather than the bank address of the PHY. This is hardly noticeable
because the only programming we do is enabling SSC or not, which is not
really causing an observable functional change.
Correct that mistake by passing down the struct brcm_sata_port structure
down to the brcm_sata_mdio_wr() and brcm_sata_mdio_rd() functions and do
the proper offsetting for 28nm, respectively 40nm platforms from there.
This means that brcm_sata_pcb_base() is now useless and is therefore
removed.
Fixes: c1602a1a0fbe ("phy: phy_brcmstb_sata: add support for MIPS-based platforms")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
diff --git a/drivers/phy/broadcom/phy-brcm-sata.c b/drivers/phy/broadcom/phy-brcm-sata.c
index 4710cfc..18251f2 100644
--- a/drivers/phy/broadcom/phy-brcm-sata.c
+++ b/drivers/phy/broadcom/phy-brcm-sata.c
@@ -186,29 +186,6 @@
PHY_CTRL_1_RESET = BIT(0),
};
-static inline void __iomem *brcm_sata_pcb_base(struct brcm_sata_port *port)
-{
- struct brcm_sata_phy *priv = port->phy_priv;
- u32 size = 0;
-
- switch (priv->version) {
- case BRCM_SATA_PHY_STB_16NM:
- case BRCM_SATA_PHY_STB_28NM:
- case BRCM_SATA_PHY_IPROC_NS2:
- case BRCM_SATA_PHY_DSL_28NM:
- size = SATA_PCB_REG_28NM_SPACE_SIZE;
- break;
- case BRCM_SATA_PHY_STB_40NM:
- size = SATA_PCB_REG_40NM_SPACE_SIZE;
- break;
- default:
- dev_err(priv->dev, "invalid phy version\n");
- break;
- }
-
- return priv->phy_base + (port->portnum * size);
-}
-
static inline void __iomem *brcm_sata_ctrl_base(struct brcm_sata_port *port)
{
struct brcm_sata_phy *priv = port->phy_priv;
@@ -226,19 +203,34 @@
return priv->ctrl_base + (port->portnum * size);
}
-static void brcm_sata_phy_wr(void __iomem *pcb_base, u32 bank,
+static void brcm_sata_phy_wr(struct brcm_sata_port *port, u32 bank,
u32 ofs, u32 msk, u32 value)
{
+ struct brcm_sata_phy *priv = port->phy_priv;
+ void __iomem *pcb_base = priv->phy_base;
u32 tmp;
+ if (priv->version == BRCM_SATA_PHY_STB_40NM)
+ bank += (port->portnum * SATA_PCB_REG_40NM_SPACE_SIZE);
+ else
+ pcb_base += (port->portnum * SATA_PCB_REG_28NM_SPACE_SIZE);
+
writel(bank, pcb_base + SATA_PCB_BANK_OFFSET);
tmp = readl(pcb_base + SATA_PCB_REG_OFFSET(ofs));
tmp = (tmp & msk) | value;
writel(tmp, pcb_base + SATA_PCB_REG_OFFSET(ofs));
}
-static u32 brcm_sata_phy_rd(void __iomem *pcb_base, u32 bank, u32 ofs)
+static u32 brcm_sata_phy_rd(struct brcm_sata_port *port, u32 bank, u32 ofs)
{
+ struct brcm_sata_phy *priv = port->phy_priv;
+ void __iomem *pcb_base = priv->phy_base;
+
+ if (priv->version == BRCM_SATA_PHY_STB_40NM)
+ bank += (port->portnum * SATA_PCB_REG_40NM_SPACE_SIZE);
+ else
+ pcb_base += (port->portnum * SATA_PCB_REG_28NM_SPACE_SIZE);
+
writel(bank, pcb_base + SATA_PCB_BANK_OFFSET);
return readl(pcb_base + SATA_PCB_REG_OFFSET(ofs));
}
@@ -250,16 +242,15 @@
static void brcm_stb_sata_ssc_init(struct brcm_sata_port *port)
{
- void __iomem *base = brcm_sata_pcb_base(port);
struct brcm_sata_phy *priv = port->phy_priv;
u32 tmp;
/* override the TX spread spectrum setting */
tmp = TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL | TXPMD_CONTROL1_TX_SSC_EN_FRC;
- brcm_sata_phy_wr(base, TXPMD_REG_BANK, TXPMD_CONTROL1, ~tmp, tmp);
+ brcm_sata_phy_wr(port, TXPMD_REG_BANK, TXPMD_CONTROL1, ~tmp, tmp);
/* set fixed min freq */
- brcm_sata_phy_wr(base, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL2,
+ brcm_sata_phy_wr(port, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL2,
~TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK,
STB_FMIN_VAL_DEFAULT);
@@ -271,7 +262,7 @@
tmp = STB_FMAX_VAL_DEFAULT;
}
- brcm_sata_phy_wr(base, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL3,
+ brcm_sata_phy_wr(port, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL3,
~TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK, tmp);
}
@@ -280,7 +271,6 @@
static int brcm_stb_sata_rxaeq_init(struct brcm_sata_port *port)
{
- void __iomem *base = brcm_sata_pcb_base(port);
u32 tmp = 0, reg = 0;
switch (port->rxaeq_mode) {
@@ -301,8 +291,8 @@
break;
}
- brcm_sata_phy_wr(base, AEQRX_REG_BANK_0, reg, ~tmp, tmp);
- brcm_sata_phy_wr(base, AEQRX_REG_BANK_1, reg, ~tmp, tmp);
+ brcm_sata_phy_wr(port, AEQRX_REG_BANK_0, reg, ~tmp, tmp);
+ brcm_sata_phy_wr(port, AEQRX_REG_BANK_1, reg, ~tmp, tmp);
return 0;
}
@@ -316,18 +306,17 @@
static int brcm_stb_sata_16nm_ssc_init(struct brcm_sata_port *port)
{
- void __iomem *base = brcm_sata_pcb_base(port);
u32 tmp, value;
/* Reduce CP tail current to 1/16th of its default value */
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL6, 0, 0x141);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL6, 0, 0x141);
/* Turn off CP tail current boost */
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL8, 0, 0xc006);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL8, 0, 0xc006);
/* Set a specific AEQ equalizer value */
tmp = AEQ_FRC_EQ_FORCE_VAL | AEQ_FRC_EQ_FORCE;
- brcm_sata_phy_wr(base, AEQRX_REG_BANK_0, AEQ_FRC_EQ,
+ brcm_sata_phy_wr(port, AEQRX_REG_BANK_0, AEQ_FRC_EQ,
~(tmp | AEQ_RFZ_FRC_VAL |
AEQ_FRC_EQ_VAL_MASK << AEQ_FRC_EQ_VAL_SHIFT),
tmp | 32 << AEQ_FRC_EQ_VAL_SHIFT);
@@ -337,7 +326,7 @@
value = 0x52;
else
value = 0;
- brcm_sata_phy_wr(base, RXPMD_REG_BANK, RXPMD_RX_CDR_CONTROL1,
+ brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CONTROL1,
~RXPMD_RX_PPM_VAL_MASK, value);
/* Set proportional loop bandwith Gen1/2/3 */
@@ -352,7 +341,7 @@
value = 1 << RXPMD_G1_CDR_PROP_BW_SHIFT |
1 << RXPMD_G2_CDR_PROP_BW_SHIFT |
1 << RXPMD_G3_CDR_PROB_BW_SHIFT;
- brcm_sata_phy_wr(base, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_PROP_BW, ~tmp,
+ brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_PROP_BW, ~tmp,
value);
/* Set CDR integral loop acquisition bandwidth for Gen1/2/3 */
@@ -365,7 +354,7 @@
1 << RXPMD_G3_CDR_ACQ_INT_BW_SHIFT;
else
value = 0;
- brcm_sata_phy_wr(base, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_ACQ_INTEG_BW,
+ brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_ACQ_INTEG_BW,
~tmp, value);
/* Set CDR integral loop locking bandwidth to 1 for Gen 1/2/3 */
@@ -378,7 +367,7 @@
1 << RXPMD_G3_CDR_LOCK_INT_BW_SHIFT;
else
value = 0;
- brcm_sata_phy_wr(base, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_LOCK_INTEG_BW,
+ brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_LOCK_INTEG_BW,
~tmp, value);
/* Set no guard band and clamp CDR */
@@ -387,11 +376,11 @@
value = 0x51;
else
value = 0;
- brcm_sata_phy_wr(base, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1,
+ brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1,
~tmp, RXPMD_MON_CORRECT_EN | value);
/* Turn on/off SSC */
- brcm_sata_phy_wr(base, TX_REG_BANK, TX_ACTRL5, ~TX_ACTRL5_SSC_EN,
+ brcm_sata_phy_wr(port, TX_REG_BANK, TX_ACTRL5, ~TX_ACTRL5_SSC_EN,
port->ssc_en ? TX_ACTRL5_SSC_EN : 0);
return 0;
@@ -411,7 +400,6 @@
{
int try;
unsigned int val;
- void __iomem *base = brcm_sata_pcb_base(port);
void __iomem *ctrl_base = brcm_sata_ctrl_base(port);
struct device *dev = port->phy_priv->dev;
@@ -421,24 +409,24 @@
val |= (0x4 << OOB_CTRL1_BURST_MIN_SHIFT);
val |= (0x9 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT);
val |= (0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT);
- brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
+ brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
val = 0x0;
val |= (0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT);
val |= (0x2 << OOB_CTRL2_BURST_CNT_SHIFT);
val |= (0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT);
- brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
+ brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
/* Configure PHY PLL register bank 1 */
val = NS2_PLL1_ACTRL2_MAGIC;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
val = NS2_PLL1_ACTRL3_MAGIC;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
val = NS2_PLL1_ACTRL4_MAGIC;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
/* Configure PHY BLOCK0 register bank */
/* Set oob_clk_sel to refclk/2 */
- brcm_sata_phy_wr(base, BLOCK0_REG_BANK, BLOCK0_SPARE,
+ brcm_sata_phy_wr(port, BLOCK0_REG_BANK, BLOCK0_SPARE,
~BLOCK0_SPARE_OOB_CLK_SEL_MASK,
BLOCK0_SPARE_OOB_CLK_SEL_REFBY2);
@@ -451,7 +439,7 @@
/* Wait for PHY PLL lock by polling pll_lock bit */
try = 50;
while (try) {
- val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ val = brcm_sata_phy_rd(port, BLOCK0_REG_BANK,
BLOCK0_XGXSSTATUS);
if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
break;
@@ -471,9 +459,7 @@
static int brcm_nsp_sata_init(struct brcm_sata_port *port)
{
- struct brcm_sata_phy *priv = port->phy_priv;
struct device *dev = port->phy_priv->dev;
- void __iomem *base = priv->phy_base;
unsigned int oob_bank;
unsigned int val, try;
@@ -490,36 +476,36 @@
val |= (0x06 << OOB_CTRL1_BURST_MIN_SHIFT);
val |= (0x0f << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT);
val |= (0x06 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT);
- brcm_sata_phy_wr(base, oob_bank, OOB_CTRL1, 0x0, val);
+ brcm_sata_phy_wr(port, oob_bank, OOB_CTRL1, 0x0, val);
val = 0x0;
val |= (0x2e << OOB_CTRL2_RESET_IDLE_MAX_SHIFT);
val |= (0x02 << OOB_CTRL2_BURST_CNT_SHIFT);
val |= (0x16 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT);
- brcm_sata_phy_wr(base, oob_bank, OOB_CTRL2, 0x0, val);
+ brcm_sata_phy_wr(port, oob_bank, OOB_CTRL2, 0x0, val);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL2,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_ACTRL2,
~(PLL_ACTRL2_SELDIV_MASK << PLL_ACTRL2_SELDIV_SHIFT),
0x0c << PLL_ACTRL2_SELDIV_SHIFT);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_CAP_CONTROL,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_CAP_CONTROL,
0xff0, 0x4f0);
val = PLLCONTROL_0_FREQ_DET_RESTART | PLLCONTROL_0_FREQ_MONITOR;
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
~val, val);
val = PLLCONTROL_0_SEQ_START;
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
~val, 0);
mdelay(10);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
~val, val);
/* Wait for pll_seq_done bit */
try = 50;
while (--try) {
- val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ val = brcm_sata_phy_rd(port, BLOCK0_REG_BANK,
BLOCK0_XGXSSTATUS);
if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
break;
@@ -546,27 +532,25 @@
static int brcm_sr_sata_init(struct brcm_sata_port *port)
{
- struct brcm_sata_phy *priv = port->phy_priv;
struct device *dev = port->phy_priv->dev;
- void __iomem *base = priv->phy_base;
unsigned int val, try;
/* Configure PHY PLL register bank 1 */
val = SR_PLL1_ACTRL2_MAGIC;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
val = SR_PLL1_ACTRL3_MAGIC;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
val = SR_PLL1_ACTRL4_MAGIC;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
/* Configure PHY PLL register bank 0 */
val = SR_PLL0_ACTRL6_MAGIC;
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val);
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val);
/* Wait for PHY PLL lock by polling pll_lock bit */
try = 50;
do {
- val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ val = brcm_sata_phy_rd(port, BLOCK0_REG_BANK,
BLOCK0_XGXSSTATUS);
if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
break;
@@ -581,7 +565,7 @@
}
/* Invert Tx polarity */
- brcm_sata_phy_wr(base, TX_REG_BANK, TX_ACTRL0,
+ brcm_sata_phy_wr(port, TX_REG_BANK, TX_ACTRL0,
~TX_ACTRL0_TXPOL_FLIP, TX_ACTRL0_TXPOL_FLIP);
/* Configure OOB control to handle 100MHz reference clock */
@@ -589,52 +573,51 @@
(0x4 << OOB_CTRL1_BURST_MIN_SHIFT) |
(0x8 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT) |
(0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT));
- brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
+ brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
val = ((0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT) |
(0x2 << OOB_CTRL2_BURST_CNT_SHIFT) |
(0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT));
- brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
+ brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
return 0;
}
static int brcm_dsl_sata_init(struct brcm_sata_port *port)
{
- void __iomem *base = brcm_sata_pcb_base(port);
struct device *dev = port->phy_priv->dev;
unsigned int try;
u32 tmp;
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL7, 0, 0x873);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL7, 0, 0x873);
- brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL6, 0, 0xc000);
+ brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL6, 0, 0xc000);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
0, 0x3089);
usleep_range(1000, 2000);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0,
0, 0x3088);
usleep_range(1000, 2000);
- brcm_sata_phy_wr(base, AEQRX_REG_BANK_1, AEQRX_SLCAL0_CTRL0,
+ brcm_sata_phy_wr(port, AEQRX_REG_BANK_1, AEQRX_SLCAL0_CTRL0,
0, 0x3000);
- brcm_sata_phy_wr(base, AEQRX_REG_BANK_1, AEQRX_SLCAL1_CTRL0,
+ brcm_sata_phy_wr(port, AEQRX_REG_BANK_1, AEQRX_SLCAL1_CTRL0,
0, 0x3000);
usleep_range(1000, 2000);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_CAP_CHARGE_TIME, 0, 0x32);
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_CAP_CHARGE_TIME, 0, 0x32);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_VCO_CAL_THRESH, 0, 0xa);
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_VCO_CAL_THRESH, 0, 0xa);
- brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_FREQ_DET_TIME, 0, 0x64);
+ brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_FREQ_DET_TIME, 0, 0x64);
usleep_range(1000, 2000);
/* Acquire PLL lock */
try = 50;
while (try) {
- tmp = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ tmp = brcm_sata_phy_rd(port, BLOCK0_REG_BANK,
BLOCK0_XGXSSTATUS);
if (tmp & BLOCK0_XGXSSTATUS_PLL_LOCK)
break;
@@ -687,10 +670,9 @@
static void brcm_stb_sata_calibrate(struct brcm_sata_port *port)
{
- void __iomem *base = brcm_sata_pcb_base(port);
u32 tmp = BIT(8);
- brcm_sata_phy_wr(base, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1,
+ brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1,
~tmp, tmp);
}
