blob: de3fa3ab34d63ae81a98bedf6c6802d359ef9b8e [file] [log] [blame]
/*
* usb_a926x.dts - Device Tree file for Caloa USB A926x board
*
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2 or later.
*/
/ {
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
dbgu: serial@fffff200 {
status = "okay";
};
tcb0: timer@fffa0000 {
timer@0 {
compatible = "atmel,tcb-timer";
reg = <0>, <1>;
};
timer@2 {
compatible = "atmel,tcb-timer";
reg = <2>;
};
};
macb0: ethernet@fffc4000 {
phy-mode = "rmii";
status = "okay";
};
usb1: gadget@fffa4000 {
atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
};
ebi: ebi@10000000 {
status = "okay";
nand_controller: nand-controller {
status = "okay";
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
pinctrl-names = "default";
nand@3 {
reg = <0x3 0x0 0x800000>;
rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
nand-bus-width = <8>;
nand-ecc-mode = "soft";
nand-on-flash-bbt;
label = "atmel_nand";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x20000>;
};
barebox@20000 {
label = "barebox";
reg = <0x20000 0x40000>;
};
bareboxenv@60000 {
label = "bareboxenv";
reg = <0x60000 0x20000>;
};
bareboxenv2@80000 {
label = "bareboxenv2";
reg = <0x80000 0x20000>;
};
oftree@80000 {
label = "oftree";
reg = <0xa0000 0x20000>;
};
kernel@a0000 {
label = "kernel";
reg = <0xc0000 0x400000>;
};
rootfs@4a0000 {
label = "rootfs";
reg = <0x4c0000 0x7800000>;
};
data@7ca0000 {
label = "data";
reg = <0x7cc0000 0x8340000>;
};
};
};
};
};
usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
};
leds {
compatible = "gpio-leds";
user_led {
label = "user_led";
gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
user_pb {
label = "user_pb";
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
linux,code = <28>;
wakeup-source;
};
};
i2c-gpio-0 {
status = "okay";
};
};