Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
diff --git a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
index b93c1e2..7c40ea6 100644
--- a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
+++ b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
@@ -1,14 +1,19 @@
* Atmel Quad Serial Peripheral Interface (QSPI)
Required properties:
-- compatible: Should be "atmel,sama5d2-qspi".
+- compatible: Should be one of the following:
+ - "atmel,sama5d2-qspi"
+ - "microchip,sam9x60-qspi"
- reg: Should contain the locations and lengths of the base registers
and the mapped memory.
- reg-names: Should contain the resource reg names:
- qspi_base: configuration register address space
- qspi_mmap: memory mapped address space
- interrupts: Should contain the interrupt for the device.
-- clocks: The phandle of the clock needed by the QSPI controller.
+- clocks: Should reference the peripheral clock and the QSPI system
+ clock if available.
+- clock-names: Should contain "pclk" for the peripheral clock and "qspick"
+ for the system clock when available.
- #address-cells: Should be <1>.
- #size-cells: Should be <0>.
@@ -19,7 +24,8 @@
reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>;
reg-names = "qspi_base", "qspi_mmap";
interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>;
- clocks = <&spi0_clk>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 52>;
+ clock-names = "pclk";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
index e3c48b2..2d32641 100644
--- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
+++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
@@ -10,6 +10,7 @@
- "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35
- "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51
- "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc
+ - "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8M
- reg : Offset and length of the register set for the device
- interrupts : Should contain CSPI/eCSPI interrupt
- clocks : Clock specifiers for both ipg and per clocks.
diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
similarity index 73%
rename from Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
rename to Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
index 483e9cf..e8f1d62 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
@@ -14,15 +14,13 @@
- clocks : The clocks needed by the QuadSPI controller
- clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
-Optional properties:
- - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
- Each bus can be connected with two NOR flashes.
- Most of the time, each bus only has one NOR flash
- connected, this is the default case.
- But if there are two NOR flashes connected to the
- bus, you should enable this property.
- (Please check the board's schematic.)
- - big-endian : That means the IP register is big endian
+Required SPI slave node properties:
+ - reg: There are two buses (A and B) with two chip selects each.
+ This encodes to which bus and CS the flash is connected:
+ <0>: Bus A, CS 0
+ <1>: Bus A, CS 1
+ <2>: Bus B, CS 0
+ <3>: Bus B, CS 1
Example:
@@ -40,7 +38,7 @@
};
};
-Example showing the usage of two SPI NOR devices:
+Example showing the usage of two SPI NOR devices on bus A:
&qspi2 {
pinctrl-names = "default";
diff --git a/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
new file mode 100644
index 0000000..2cd67eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
@@ -0,0 +1,39 @@
+* NXP Flex Serial Peripheral Interface (FSPI)
+
+Required properties:
+ - compatible : Should be "nxp,lx2160a-fspi"
+ - reg : First contains the register location and length,
+ Second contains the memory mapping address and length
+ - reg-names : Should contain the resource reg names:
+ - fspi_base: configuration register address space
+ - fspi_mmap: memory mapped address space
+ - interrupts : Should contain the interrupt for the device
+
+Required SPI slave node properties:
+ - reg : There are two buses (A and B) with two chip selects each.
+ This encodes to which bus and CS the flash is connected:
+ - <0>: Bus A, CS 0
+ - <1>: Bus A, CS 1
+ - <2>: Bus B, CS 0
+ - <3>: Bus B, CS 1
+
+Example showing the usage of two SPI NOR slave devices on bus A:
+
+fspi0: spi@20c0000 {
+ compatible = "nxp,lx2160a-fspi";
+ reg = <0x0 0x20c0000 0x0 0x10000>, <0x0 0x20000000 0x0 0x10000000>;
+ reg-names = "fspi_base", "fspi_mmap";
+ interrupts = <0 25 0x4>; /* Level high type */
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "fspi_en", "fspi";
+
+ mt35xu512aba0: flash@0 {
+ reg = <0>;
+ ....
+ };
+
+ mt35xu512aba1: flash@1 {
+ reg = <1>;
+ ....
+ };
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.txt b/Documentation/devicetree/bindings/spi/spi-sifive.txt
new file mode 100644
index 0000000..3f5c6e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-sifive.txt
@@ -0,0 +1,37 @@
+SiFive SPI controller Device Tree Bindings
+------------------------------------------
+
+Required properties:
+- compatible : Should be "sifive,<chip>-spi" and "sifive,spi<version>".
+ Supported compatible strings are:
+ "sifive,fu540-c000-spi" for the SiFive SPI v0 as integrated
+ onto the SiFive FU540 chip, and "sifive,spi0" for the SiFive
+ SPI v0 IP block with no chip integration tweaks.
+ Please refer to sifive-blocks-ip-versioning.txt for details
+- reg : Physical base address and size of SPI registers map
+ A second (optional) range can indicate memory mapped flash
+- interrupts : Must contain one entry
+- interrupt-parent : Must be core interrupt controller
+- clocks : Must reference the frequency given to the controller
+- #address-cells : Must be '1', indicating which CS to use
+- #size-cells : Must be '0'
+
+Optional properties:
+- sifive,fifo-depth : Depth of hardware queues; defaults to 8
+- sifive,max-bits-per-word : Maximum bits per word; defaults to 8
+
+SPI RTL that corresponds to the IP block version numbers can be found here:
+https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/spi
+
+Example:
+ spi: spi@10040000 {
+ compatible = "sifive,fu540-c000-spi", "sifive,spi0";
+ reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>;
+ interrupt-parent = <&plic>;
+ interrupts = <51>;
+ clocks = <&tlclk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ sifive,fifo-depth = <8>;
+ sifive,max-bits-per-word = <8>;
+ };
diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt
index bad211a..3c7eacc 100644
--- a/Documentation/devicetree/bindings/spi/spi-sprd.txt
+++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt
@@ -14,6 +14,11 @@
address on the SPI bus. Should be set to 1.
- #size-cells: Should be set to 0.
+Optional properties:
+dma-names: Should contain names of the SPI used DMA channel.
+dmas: Should contain DMA channels and DMA slave ids which the SPI used
+ sorted in the same order as the dma-names property.
+
Example:
spi0: spi@70a00000{
compatible = "sprd,sc9860-spi";
@@ -21,6 +26,8 @@
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "spi", "source","enable";
clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>;
+ dma-names = "rx_chn", "tx_chn";
+ dmas = <&apdma 11 11>, <&apdma 12 12>;
#address-cells = <1>;
#size-cells = <0>;
};
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt
index 1b3fa2c1..d82755c 100644
--- a/Documentation/devicetree/bindings/spi/spi-stm32.txt
+++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt
@@ -7,7 +7,9 @@
only master is supported by the driver.
Required properties:
-- compatible: Must be "st,stm32h7-spi".
+- compatible: Should be one of:
+ "st,stm32h7-spi"
+ "st,stm32f4-spi"
- reg: Offset and length of the device's register set.
- interrupts: Must contain the interrupt id.
- clocks: Must contain an entry for spiclk (which feeds the internal clock
@@ -30,8 +32,9 @@
See ../spi/spi-bus.txt
Optional properties:
-- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in
- nanoseconds inserted between two consecutive data frames.
+- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time
+ delay in nanoseconds inserted between two consecutive data
+ frames.
Example:
diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index 13a0b7f..551325b 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -21,15 +21,15 @@
"platform device". The master configuration is passed to the driver via a table
found in include/linux/spi/pxa2xx_spi.h:
-struct pxa2xx_spi_master {
+struct pxa2xx_spi_controller {
u16 num_chipselect;
u8 enable_dma;
};
-The "pxa2xx_spi_master.num_chipselect" field is used to determine the number of
+The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of
slave device (chips) attached to this SPI master.
-The "pxa2xx_spi_master.enable_dma" field informs the driver that SSP DMA should
+The "pxa2xx_spi_controller.enable_dma" field informs the driver that SSP DMA should
be used. This caused the driver to acquire two DMA channels: rx_channel and
tx_channel. The rx_channel has a higher DMA service priority the tx_channel.
See the "PXA2xx Developer Manual" section "DMA Controller".
@@ -51,7 +51,7 @@
},
};
-static struct pxa2xx_spi_master pxa_nssp_master_info = {
+static struct pxa2xx_spi_controller pxa_nssp_master_info = {
.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
.enable_dma = 1, /* Enables NSSP DMA */
};
@@ -206,7 +206,7 @@
-----------------------
The pxa2xx_spi driver supports both DMA and interrupt driven PIO message
transfers. The driver defaults to PIO mode and DMA transfers must be enabled
-by setting the "enable_dma" flag in the "pxa2xx_spi_master" structure. The DMA
+by setting the "enable_dma" flag in the "pxa2xx_spi_controller" structure. The DMA
mode supports both coherent and stream based DMA mappings.
The following logic is used to determine the type of I/O to be used on
diff --git a/MAINTAINERS b/MAINTAINERS
index 84857bc..7f06c13 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6105,9 +6105,9 @@
FREESCALE QUAD SPI DRIVER
M: Han Xu <han.xu@nxp.com>
-L: linux-mtd@lists.infradead.org
+L: linux-spi@vger.kernel.org
S: Maintained
-F: drivers/mtd/spi-nor/fsl-quadspi.c
+F: drivers/spi/spi-fsl-qspi.c
FREESCALE QUICC ENGINE LIBRARY
M: Qiang Zhao <qiang.zhao@nxp.com>
@@ -10952,6 +10952,14 @@
F: lib/test_objagg.c
F: include/linux/objagg.h
+NXP FSPI DRIVER
+R: Yogesh Gaur <yogeshgaur.83@gmail.com>
+M: Ashish Kumar <ashish.kumar@nxp.com>
+L: linux-spi@vger.kernel.org
+S: Maintained
+F: drivers/spi/spi-nxp-fspi.c
+F: Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt
+
OBJTOOL
M: Josh Poimboeuf <jpoimboe@redhat.com>
M: Peter Zijlstra <peterz@infradead.org>
diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c
index fa8e7dd..4401dfc 100644
--- a/arch/arm/mach-pxa/cm-x255.c
+++ b/arch/arm/mach-pxa/cm-x255.c
@@ -98,7 +98,7 @@
};
#if defined(CONFIG_SPI_PXA2XX)
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c
index f7081a5..279eeca 100644
--- a/arch/arm/mach-pxa/cm-x270.c
+++ b/arch/arm/mach-pxa/cm-x270.c
@@ -313,7 +313,7 @@
#endif
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master cm_x270_spi_info = {
+static struct pxa2xx_spi_controller cm_x270_spi_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c
index c9732cac..7ecf559 100644
--- a/arch/arm/mach-pxa/corgi.c
+++ b/arch/arm/mach-pxa/corgi.c
@@ -530,7 +530,7 @@
};
#if IS_ENABLED(CONFIG_SPI_PXA2XX)
-static struct pxa2xx_spi_master corgi_spi_info = {
+static struct pxa2xx_spi_controller corgi_spi_info = {
.num_chipselect = 3,
};
diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c
index a24783a..524d609 100644
--- a/arch/arm/mach-pxa/devices.c
+++ b/arch/arm/mach-pxa/devices.c
@@ -1065,7 +1065,7 @@
/* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1.
* See comment in arch/arm/mach-pxa/ssp.c::ssp_probe() */
-void __init pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info)
+void __init pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_controller *info)
{
struct platform_device *pd;
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index 5ba7bb7..fa3adb0 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -689,7 +689,7 @@
#endif
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master em_x270_spi_info = {
+static struct pxa2xx_spi_controller em_x270_spi_info = {
.num_chipselect = 1,
};
@@ -703,7 +703,7 @@
.model = TDO35S,
};
-static struct pxa2xx_spi_master em_x270_spi_2_info = {
+static struct pxa2xx_spi_controller em_x270_spi_2_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index 51d38d5..1d6b1d2 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -630,7 +630,7 @@
},
};
-static struct pxa2xx_spi_master pxa_ssp2_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp2_master_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c
index cbaf4f6..7e30452 100644
--- a/arch/arm/mach-pxa/icontrol.c
+++ b/arch/arm/mach-pxa/icontrol.c
@@ -115,12 +115,12 @@
}
};
-static struct pxa2xx_spi_master pxa_ssp3_spi_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp3_spi_master_info = {
.num_chipselect = 2,
.enable_dma = 1
};
-static struct pxa2xx_spi_master pxa_ssp4_spi_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp4_spi_master_info = {
.num_chipselect = 2,
.enable_dma = 1
};
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index 39db489..464b8bd 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -191,7 +191,7 @@
#endif /* CONFIG_FB_PXA || CONFIG_FB_PXA_MODULE */
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master littleton_spi_info = {
+static struct pxa2xx_spi_controller littleton_spi_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index a1391e1..c1bd0d5 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -197,7 +197,7 @@
* (to J5) and poking board registers (as done below). Else it's only useful
* for the temperature sensors.
*/
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 6538a7c..75abc21 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -940,7 +940,7 @@
.gpio_cs = GPIO14_MAGICIAN_TSC2046_CS,
};
-static struct pxa2xx_spi_master magician_spi_info = {
+static struct pxa2xx_spi_controller magician_spi_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
diff --git a/arch/arm/mach-pxa/pcm027.c b/arch/arm/mach-pxa/pcm027.c
index ccca9f7..e2e6134 100644
--- a/arch/arm/mach-pxa/pcm027.c
+++ b/arch/arm/mach-pxa/pcm027.c
@@ -132,7 +132,7 @@
/*
* SPI host and devices
*/
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c
index c2a43d4..9450a52 100644
--- a/arch/arm/mach-pxa/poodle.c
+++ b/arch/arm/mach-pxa/poodle.c
@@ -196,7 +196,7 @@
EXPORT_SYMBOL(poodle_locomo_device);
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master poodle_spi_info = {
+static struct pxa2xx_spi_controller poodle_spi_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 306818e..8dac824 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -572,7 +572,7 @@
},
};
-static struct pxa2xx_spi_master spitz_spi_info = {
+static struct pxa2xx_spi_controller spitz_spi_info = {
.num_chipselect = 3,
};
diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c
index e0d6c872..c28d19b 100644
--- a/arch/arm/mach-pxa/stargate2.c
+++ b/arch/arm/mach-pxa/stargate2.c
@@ -337,15 +337,15 @@
.num_resources = 1,
};
-static struct pxa2xx_spi_master pxa_ssp_master_0_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_0_info = {
.num_chipselect = 1,
};
-static struct pxa2xx_spi_master pxa_ssp_master_1_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_1_info = {
.num_chipselect = 1,
};
-static struct pxa2xx_spi_master pxa_ssp_master_2_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_2_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c
index e8a93c0..7439798 100644
--- a/arch/arm/mach-pxa/tosa.c
+++ b/arch/arm/mach-pxa/tosa.c
@@ -813,7 +813,7 @@
.dev.platform_data = &tosa_bt_data,
};
-static struct pxa2xx_spi_master pxa_ssp_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp_master_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c
index e2353e7..ad082e1 100644
--- a/arch/arm/mach-pxa/z2.c
+++ b/arch/arm/mach-pxa/z2.c
@@ -607,12 +607,12 @@
},
};
-static struct pxa2xx_spi_master pxa_ssp1_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp1_master_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
-static struct pxa2xx_spi_master pxa_ssp2_master_info = {
+static struct pxa2xx_spi_controller pxa_ssp2_master_info = {
.num_chipselect = 1,
};
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index ebd6543..3fd1119 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -391,7 +391,7 @@
};
/* SPI interface on SSP3 */
-static struct pxa2xx_spi_master pxa2xx_spi_ssp3_master_info = {
+static struct pxa2xx_spi_controller pxa2xx_spi_ssp3_master_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
diff --git a/arch/mips/ath79/dev-spi.h b/arch/mips/ath79/dev-spi.h
index d732565..6e15bc8 100644
--- a/arch/mips/ath79/dev-spi.h
+++ b/arch/mips/ath79/dev-spi.h
@@ -13,7 +13,7 @@
#define _ATH79_DEV_SPI_H
#include <linux/spi/spi.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
void ath79_register_spi(struct ath79_spi_platform_data *pdata,
struct spi_board_info const *info,
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index a6e1891..c34eb9d 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -125,7 +125,7 @@
for_each_child_of_node(np, child) {
ret = of_property_read_u32(child, "reg", &cs);
- if (!ret)
+ if (ret)
continue;
if (cs == index) {
/*
diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
index 414e887..dab9866 100644
--- a/drivers/mtd/spi-nor/Kconfig
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -42,15 +42,6 @@
device with a Cadence QSPI controller and want to access the
Flash as an MTD device.
-config SPI_FSL_QUADSPI
- tristate "Freescale Quad SPI controller"
- depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
- depends on HAS_IOMEM
- help
- This enables support for the Quad SPI controller in master mode.
- This controller does not support generic SPI. It only supports
- SPI NOR.
-
config SPI_HISI_SFC
tristate "Hisilicon SPI-NOR Flash Controller(SFC)"
depends on ARCH_HISI || COMPILE_TEST
diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
index 4e4d400..189a15c 100644
--- a/drivers/mtd/spi-nor/Makefile
+++ b/drivers/mtd/spi-nor/Makefile
@@ -2,7 +2,6 @@
obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o
obj-$(CONFIG_SPI_ASPEED_SMC) += aspeed-smc.o
obj-$(CONFIG_SPI_CADENCE_QUADSPI) += cadence-quadspi.o
-obj-$(CONFIG_SPI_FSL_QUADSPI) += fsl-quadspi.o
obj-$(CONFIG_SPI_HISI_SFC) += hisi-sfc.o
obj-$(CONFIG_SPI_MTK_QUADSPI) += mtk-quadspi.o
obj-$(CONFIG_SPI_NXP_SPIFI) += nxp-spifi.o
diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
deleted file mode 100644
index 1ff3430..0000000
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ /dev/null
@@ -1,1224 +0,0 @@
-/*
- * Freescale QuadSPI driver.
- *
- * Copyright (C) 2013 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/errno.h>
-#include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/timer.h>
-#include <linux/jiffies.h>
-#include <linux/completion.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/spi-nor.h>
-#include <linux/mutex.h>
-#include <linux/pm_qos.h>
-#include <linux/sizes.h>
-
-/* Controller needs driver to swap endian */
-#define QUADSPI_QUIRK_SWAP_ENDIAN (1 << 0)
-/* Controller needs 4x internal clock */
-#define QUADSPI_QUIRK_4X_INT_CLK (1 << 1)
-/*
- * TKT253890, Controller needs driver to fill txfifo till 16 byte to
- * trigger data transfer even though extern data will not transferred.
- */
-#define QUADSPI_QUIRK_TKT253890 (1 << 2)
-/* Controller cannot wake up from wait mode, TKT245618 */
-#define QUADSPI_QUIRK_TKT245618 (1 << 3)
-
-/* The registers */
-#define QUADSPI_MCR 0x00
-#define QUADSPI_MCR_RESERVED_SHIFT 16
-#define QUADSPI_MCR_RESERVED_MASK (0xF << QUADSPI_MCR_RESERVED_SHIFT)
-#define QUADSPI_MCR_MDIS_SHIFT 14
-#define QUADSPI_MCR_MDIS_MASK (1 << QUADSPI_MCR_MDIS_SHIFT)
-#define QUADSPI_MCR_CLR_TXF_SHIFT 11
-#define QUADSPI_MCR_CLR_TXF_MASK (1 << QUADSPI_MCR_CLR_TXF_SHIFT)
-#define QUADSPI_MCR_CLR_RXF_SHIFT 10
-#define QUADSPI_MCR_CLR_RXF_MASK (1 << QUADSPI_MCR_CLR_RXF_SHIFT)
-#define QUADSPI_MCR_DDR_EN_SHIFT 7
-#define QUADSPI_MCR_DDR_EN_MASK (1 << QUADSPI_MCR_DDR_EN_SHIFT)
-#define QUADSPI_MCR_END_CFG_SHIFT 2
-#define QUADSPI_MCR_END_CFG_MASK (3 << QUADSPI_MCR_END_CFG_SHIFT)
-#define QUADSPI_MCR_SWRSTHD_SHIFT 1
-#define QUADSPI_MCR_SWRSTHD_MASK (1 << QUADSPI_MCR_SWRSTHD_SHIFT)
-#define QUADSPI_MCR_SWRSTSD_SHIFT 0
-#define QUADSPI_MCR_SWRSTSD_MASK (1 << QUADSPI_MCR_SWRSTSD_SHIFT)
-
-#define QUADSPI_IPCR 0x08
-#define QUADSPI_IPCR_SEQID_SHIFT 24
-#define QUADSPI_IPCR_SEQID_MASK (0xF << QUADSPI_IPCR_SEQID_SHIFT)
-
-#define QUADSPI_BUF0CR 0x10
-#define QUADSPI_BUF1CR 0x14
-#define QUADSPI_BUF2CR 0x18
-#define QUADSPI_BUFXCR_INVALID_MSTRID 0xe
-
-#define QUADSPI_BUF3CR 0x1c
-#define QUADSPI_BUF3CR_ALLMST_SHIFT 31
-#define QUADSPI_BUF3CR_ALLMST_MASK (1 << QUADSPI_BUF3CR_ALLMST_SHIFT)
-#define QUADSPI_BUF3CR_ADATSZ_SHIFT 8
-#define QUADSPI_BUF3CR_ADATSZ_MASK (0xFF << QUADSPI_BUF3CR_ADATSZ_SHIFT)
-
-#define QUADSPI_BFGENCR 0x20
-#define QUADSPI_BFGENCR_PAR_EN_SHIFT 16
-#define QUADSPI_BFGENCR_PAR_EN_MASK (1 << (QUADSPI_BFGENCR_PAR_EN_SHIFT))
-#define QUADSPI_BFGENCR_SEQID_SHIFT 12
-#define QUADSPI_BFGENCR_SEQID_MASK (0xF << QUADSPI_BFGENCR_SEQID_SHIFT)
-
-#define QUADSPI_BUF0IND 0x30
-#define QUADSPI_BUF1IND 0x34
-#define QUADSPI_BUF2IND 0x38
-#define QUADSPI_SFAR 0x100
-
-#define QUADSPI_SMPR 0x108
-#define QUADSPI_SMPR_DDRSMP_SHIFT 16
-#define QUADSPI_SMPR_DDRSMP_MASK (7 << QUADSPI_SMPR_DDRSMP_SHIFT)
-#define QUADSPI_SMPR_FSDLY_SHIFT 6
-#define QUADSPI_SMPR_FSDLY_MASK (1 << QUADSPI_SMPR_FSDLY_SHIFT)
-#define QUADSPI_SMPR_FSPHS_SHIFT 5
-#define QUADSPI_SMPR_FSPHS_MASK (1 << QUADSPI_SMPR_FSPHS_SHIFT)
-#define QUADSPI_SMPR_HSENA_SHIFT 0
-#define QUADSPI_SMPR_HSENA_MASK (1 << QUADSPI_SMPR_HSENA_SHIFT)
-
-#define QUADSPI_RBSR 0x10c
-#define QUADSPI_RBSR_RDBFL_SHIFT 8
-#define QUADSPI_RBSR_RDBFL_MASK (0x3F << QUADSPI_RBSR_RDBFL_SHIFT)
-
-#define QUADSPI_RBCT 0x110
-#define QUADSPI_RBCT_WMRK_MASK 0x1F
-#define QUADSPI_RBCT_RXBRD_SHIFT 8
-#define QUADSPI_RBCT_RXBRD_USEIPS (0x1 << QUADSPI_RBCT_RXBRD_SHIFT)
-
-#define QUADSPI_TBSR 0x150
-#define QUADSPI_TBDR 0x154
-#define QUADSPI_SR 0x15c
-#define QUADSPI_SR_IP_ACC_SHIFT 1
-#define QUADSPI_SR_IP_ACC_MASK (0x1 << QUADSPI_SR_IP_ACC_SHIFT)
-#define QUADSPI_SR_AHB_ACC_SHIFT 2
-#define QUADSPI_SR_AHB_ACC_MASK (0x1 << QUADSPI_SR_AHB_ACC_SHIFT)
-
-#define QUADSPI_FR 0x160
-#define QUADSPI_FR_TFF_MASK 0x1
-
-#define QUADSPI_SFA1AD 0x180
-#define QUADSPI_SFA2AD 0x184
-#define QUADSPI_SFB1AD 0x188
-#define QUADSPI_SFB2AD 0x18c
-#define QUADSPI_RBDR 0x200
-
-#define QUADSPI_LUTKEY 0x300
-#define QUADSPI_LUTKEY_VALUE 0x5AF05AF0
-
-#define QUADSPI_LCKCR 0x304
-#define QUADSPI_LCKER_LOCK 0x1
-#define QUADSPI_LCKER_UNLOCK 0x2
-
-#define QUADSPI_RSER 0x164
-#define QUADSPI_RSER_TFIE (0x1 << 0)
-
-#define QUADSPI_LUT_BASE 0x310
-
-/*
- * The definition of the LUT register shows below:
- *
- * ---------------------------------------------------
- * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
- * ---------------------------------------------------
- */
-#define OPRND0_SHIFT 0
-#define PAD0_SHIFT 8
-#define INSTR0_SHIFT 10
-#define OPRND1_SHIFT 16
-
-/* Instruction set for the LUT register. */
-#define LUT_STOP 0
-#define LUT_CMD 1
-#define LUT_ADDR 2
-#define LUT_DUMMY 3
-#define LUT_MODE 4
-#define LUT_MODE2 5
-#define LUT_MODE4 6
-#define LUT_FSL_READ 7
-#define LUT_FSL_WRITE 8
-#define LUT_JMP_ON_CS 9
-#define LUT_ADDR_DDR 10
-#define LUT_MODE_DDR 11
-#define LUT_MODE2_DDR 12
-#define LUT_MODE4_DDR 13
-#define LUT_FSL_READ_DDR 14
-#define LUT_FSL_WRITE_DDR 15
-#define LUT_DATA_LEARN 16
-
-/*
- * The PAD definitions for LUT register.
- *
- * The pad stands for the lines number of IO[0:3].
- * For example, the Quad read need four IO lines, so you should
- * set LUT_PAD4 which means we use four IO lines.
- */
-#define LUT_PAD1 0
-#define LUT_PAD2 1
-#define LUT_PAD4 2
-
-/* Oprands for the LUT register. */
-#define ADDR24BIT 0x18
-#define ADDR32BIT 0x20
-
-/* Macros for constructing the LUT register. */
-#define LUT0(ins, pad, opr) \
- (((opr) << OPRND0_SHIFT) | ((LUT_##pad) << PAD0_SHIFT) | \
- ((LUT_##ins) << INSTR0_SHIFT))
-
-#define LUT1(ins, pad, opr) (LUT0(ins, pad, opr) << OPRND1_SHIFT)
-
-/* other macros for LUT register. */
-#define QUADSPI_LUT(x) (QUADSPI_LUT_BASE + (x) * 4)
-#define QUADSPI_LUT_NUM 64
-
-/* SEQID -- we can have 16 seqids at most. */
-#define SEQID_READ 0
-#define SEQID_WREN 1
-#define SEQID_WRDI 2
-#define SEQID_RDSR 3
-#define SEQID_SE 4
-#define SEQID_CHIP_ERASE 5
-#define SEQID_PP 6
-#define SEQID_RDID 7
-#define SEQID_WRSR 8
-#define SEQID_RDCR 9
-#define SEQID_EN4B 10
-#define SEQID_BRWR 11
-
-#define QUADSPI_MIN_IOMAP SZ_4M
-
-enum fsl_qspi_devtype {
- FSL_QUADSPI_VYBRID,
- FSL_QUADSPI_IMX6SX,
- FSL_QUADSPI_IMX7D,
- FSL_QUADSPI_IMX6UL,
- FSL_QUADSPI_LS1021A,
- FSL_QUADSPI_LS2080A,
-};
-
-struct fsl_qspi_devtype_data {
- enum fsl_qspi_devtype devtype;
- int rxfifo;
- int txfifo;
- int ahb_buf_size;
- int driver_data;
-};
-
-static const struct fsl_qspi_devtype_data vybrid_data = {
- .devtype = FSL_QUADSPI_VYBRID,
- .rxfifo = 128,
- .txfifo = 64,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_SWAP_ENDIAN,
-};
-
-static const struct fsl_qspi_devtype_data imx6sx_data = {
- .devtype = FSL_QUADSPI_IMX6SX,
- .rxfifo = 128,
- .txfifo = 512,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_4X_INT_CLK
- | QUADSPI_QUIRK_TKT245618,
-};
-
-static const struct fsl_qspi_devtype_data imx7d_data = {
- .devtype = FSL_QUADSPI_IMX7D,
- .rxfifo = 512,
- .txfifo = 512,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_TKT253890
- | QUADSPI_QUIRK_4X_INT_CLK,
-};
-
-static const struct fsl_qspi_devtype_data imx6ul_data = {
- .devtype = FSL_QUADSPI_IMX6UL,
- .rxfifo = 128,
- .txfifo = 512,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_TKT253890
- | QUADSPI_QUIRK_4X_INT_CLK,
-};
-
-static struct fsl_qspi_devtype_data ls1021a_data = {
- .devtype = FSL_QUADSPI_LS1021A,
- .rxfifo = 128,
- .txfifo = 64,
- .ahb_buf_size = 1024,
- .driver_data = 0,
-};
-
-static const struct fsl_qspi_devtype_data ls2080a_data = {
- .devtype = FSL_QUADSPI_LS2080A,
- .rxfifo = 128,
- .txfifo = 64,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_TKT253890,
-};
-
-
-#define FSL_QSPI_MAX_CHIP 4
-struct fsl_qspi {
- struct spi_nor nor[FSL_QSPI_MAX_CHIP];
- void __iomem *iobase;
- void __iomem *ahb_addr;
- u32 memmap_phy;
- u32 memmap_offs;
- u32 memmap_len;
- struct clk *clk, *clk_en;
- struct device *dev;
- struct completion c;
- const struct fsl_qspi_devtype_data *devtype_data;
- u32 nor_size;
- u32 nor_num;
- u32 clk_rate;
- unsigned int chip_base_addr; /* We may support two chips. */
- bool has_second_chip;
- bool big_endian;
- struct mutex lock;
- struct pm_qos_request pm_qos_req;
-};
-
-static inline int needs_swap_endian(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_SWAP_ENDIAN;
-}
-
-static inline int needs_4x_clock(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_4X_INT_CLK;
-}
-
-static inline int needs_fill_txfifo(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_TKT253890;
-}
-
-static inline int needs_wakeup_wait_mode(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_TKT245618;
-}
-
-/*
- * R/W functions for big- or little-endian registers:
- * The qSPI controller's endian is independent of the CPU core's endian.
- * So far, although the CPU core is little-endian but the qSPI have two
- * versions for big-endian and little-endian.
- */
-static void qspi_writel(struct fsl_qspi *q, u32 val, void __iomem *addr)
-{
- if (q->big_endian)
- iowrite32be(val, addr);
- else
- iowrite32(val, addr);
-}
-
-static u32 qspi_readl(struct fsl_qspi *q, void __iomem *addr)
-{
- if (q->big_endian)
- return ioread32be(addr);
- else
- return ioread32(addr);
-}
-
-/*
- * An IC bug makes us to re-arrange the 32-bit data.
- * The following chips, such as IMX6SLX, have fixed this bug.
- */
-static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a)
-{
- return needs_swap_endian(q) ? __swab32(a) : a;
-}
-
-static inline void fsl_qspi_unlock_lut(struct fsl_qspi *q)
-{
- qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
- qspi_writel(q, QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR);
-}
-
-static inline void fsl_qspi_lock_lut(struct fsl_qspi *q)
-{
- qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
- qspi_writel(q, QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR);
-}
-
-static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id)
-{
- struct fsl_qspi *q = dev_id;
- u32 reg;
-
- /* clear interrupt */
- reg = qspi_readl(q, q->iobase + QUADSPI_FR);
- qspi_writel(q, reg, q->iobase + QUADSPI_FR);
-
- if (reg & QUADSPI_FR_TFF_MASK)
- complete(&q->c);
-
- dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", q->chip_base_addr, reg);
- return IRQ_HANDLED;
-}
-
-static void fsl_qspi_init_lut(struct fsl_qspi *q)
-{
- void __iomem *base = q->iobase;
- int rxfifo = q->devtype_data->rxfifo;
- u32 lut_base;
- int i;
-
- struct spi_nor *nor = &q->nor[0];
- u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
- u8 read_op = nor->read_opcode;
- u8 read_dm = nor->read_dummy;
-
- fsl_qspi_unlock_lut(q);
-
- /* Clear all the LUT table */
- for (i = 0; i < QUADSPI_LUT_NUM; i++)
- qspi_writel(q, 0, base + QUADSPI_LUT_BASE + i * 4);
-
- /* Read */
- lut_base = SEQID_READ * 4;
-
- qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
- base + QUADSPI_LUT(lut_base));
- qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
- LUT1(FSL_READ, PAD4, rxfifo),
- base + QUADSPI_LUT(lut_base + 1));
-
- /* Write enable */
- lut_base = SEQID_WREN * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WREN),
- base + QUADSPI_LUT(lut_base));
-
- /* Page Program */
- lut_base = SEQID_PP * 4;
-
- qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
- LUT1(ADDR, PAD1, addrlen),
- base + QUADSPI_LUT(lut_base));
- qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
- base + QUADSPI_LUT(lut_base + 1));
-
- /* Read Status */
- lut_base = SEQID_RDSR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDSR) |
- LUT1(FSL_READ, PAD1, 0x1),
- base + QUADSPI_LUT(lut_base));
-
- /* Erase a sector */
- lut_base = SEQID_SE * 4;
-
- qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
- LUT1(ADDR, PAD1, addrlen),
- base + QUADSPI_LUT(lut_base));
-
- /* Erase the whole chip */
- lut_base = SEQID_CHIP_ERASE * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_CHIP_ERASE),
- base + QUADSPI_LUT(lut_base));
-
- /* READ ID */
- lut_base = SEQID_RDID * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDID) |
- LUT1(FSL_READ, PAD1, 0x8),
- base + QUADSPI_LUT(lut_base));
-
- /* Write Register */
- lut_base = SEQID_WRSR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WRSR) |
- LUT1(FSL_WRITE, PAD1, 0x2),
- base + QUADSPI_LUT(lut_base));
-
- /* Read Configuration Register */
- lut_base = SEQID_RDCR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDCR) |
- LUT1(FSL_READ, PAD1, 0x1),
- base + QUADSPI_LUT(lut_base));
-
- /* Write disable */
- lut_base = SEQID_WRDI * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WRDI),
- base + QUADSPI_LUT(lut_base));
-
- /* Enter 4 Byte Mode (Micron) */
- lut_base = SEQID_EN4B * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_EN4B),
- base + QUADSPI_LUT(lut_base));
-
- /* Enter 4 Byte Mode (Spansion) */
- lut_base = SEQID_BRWR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_BRWR),
- base + QUADSPI_LUT(lut_base));
-
- fsl_qspi_lock_lut(q);
-}
-
-/* Get the SEQID for the command */
-static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
-{
- switch (cmd) {
- case SPINOR_OP_READ_1_1_4:
- case SPINOR_OP_READ_1_1_4_4B:
- return SEQID_READ;
- case SPINOR_OP_WREN:
- return SEQID_WREN;
- case SPINOR_OP_WRDI:
- return SEQID_WRDI;
- case SPINOR_OP_RDSR:
- return SEQID_RDSR;
- case SPINOR_OP_SE:
- return SEQID_SE;
- case SPINOR_OP_CHIP_ERASE:
- return SEQID_CHIP_ERASE;
- case SPINOR_OP_PP:
- return SEQID_PP;
- case SPINOR_OP_RDID:
- return SEQID_RDID;
- case SPINOR_OP_WRSR:
- return SEQID_WRSR;
- case SPINOR_OP_RDCR:
- return SEQID_RDCR;
- case SPINOR_OP_EN4B:
- return SEQID_EN4B;
- case SPINOR_OP_BRWR:
- return SEQID_BRWR;
- default:
- if (cmd == q->nor[0].erase_opcode)
- return SEQID_SE;
- dev_err(q->dev, "Unsupported cmd 0x%.2x\n", cmd);
- break;
- }
- return -EINVAL;
-}
-
-static int
-fsl_qspi_runcmd(struct fsl_qspi *q, u8 cmd, unsigned int addr, int len)
-{
- void __iomem *base = q->iobase;
- int seqid;
- u32 reg, reg2;
- int err;
-
- init_completion(&q->c);
- dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len:%d, cmd:%.2x\n",
- q->chip_base_addr, addr, len, cmd);
-
- /* save the reg */
- reg = qspi_readl(q, base + QUADSPI_MCR);
-
- qspi_writel(q, q->memmap_phy + q->chip_base_addr + addr,
- base + QUADSPI_SFAR);
- qspi_writel(q, QUADSPI_RBCT_WMRK_MASK | QUADSPI_RBCT_RXBRD_USEIPS,
- base + QUADSPI_RBCT);
- qspi_writel(q, reg | QUADSPI_MCR_CLR_RXF_MASK, base + QUADSPI_MCR);
-
- do {
- reg2 = qspi_readl(q, base + QUADSPI_SR);
- if (reg2 & (QUADSPI_SR_IP_ACC_MASK | QUADSPI_SR_AHB_ACC_MASK)) {
- udelay(1);
- dev_dbg(q->dev, "The controller is busy, 0x%x\n", reg2);
- continue;
- }
- break;
- } while (1);
-
- /* trigger the LUT now */
- seqid = fsl_qspi_get_seqid(q, cmd);
- if (seqid < 0)
- return seqid;
-
- qspi_writel(q, (seqid << QUADSPI_IPCR_SEQID_SHIFT) | len,
- base + QUADSPI_IPCR);
-
- /* Wait for the interrupt. */
- if (!wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000))) {
- dev_err(q->dev,
- "cmd 0x%.2x timeout, addr@%.8x, FR:0x%.8x, SR:0x%.8x\n",
- cmd, addr, qspi_readl(q, base + QUADSPI_FR),
- qspi_readl(q, base + QUADSPI_SR));
- err = -ETIMEDOUT;
- } else {
- err = 0;
- }
-
- /* restore the MCR */
- qspi_writel(q, reg, base + QUADSPI_MCR);
-
- return err;
-}
-
-/* Read out the data from the QUADSPI_RBDR buffer registers. */
-static void fsl_qspi_read_data(struct fsl_qspi *q, int len, u8 *rxbuf)
-{
- u32 tmp;
- int i = 0;
-
- while (len > 0) {
- tmp = qspi_readl(q, q->iobase + QUADSPI_RBDR + i * 4);
- tmp = fsl_qspi_endian_xchg(q, tmp);
- dev_dbg(q->dev, "chip addr:0x%.8x, rcv:0x%.8x\n",
- q->chip_base_addr, tmp);
-
- if (len >= 4) {
- *((u32 *)rxbuf) = tmp;
- rxbuf += 4;
- } else {
- memcpy(rxbuf, &tmp, len);
- break;
- }
-
- len -= 4;
- i++;
- }
-}
-
-/*
- * If we have changed the content of the flash by writing or erasing,
- * we need to invalidate the AHB buffer. If we do not do so, we may read out
- * the wrong data. The spec tells us reset the AHB domain and Serial Flash
- * domain at the same time.
- */
-static inline void fsl_qspi_invalid(struct fsl_qspi *q)
-{
- u32 reg;
-
- reg = qspi_readl(q, q->iobase + QUADSPI_MCR);
- reg |= QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK;
- qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
-
- /*
- * The minimum delay : 1 AHB + 2 SFCK clocks.
- * Delay 1 us is enough.
- */
- udelay(1);
-
- reg &= ~(QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK);
- qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
-}
-
-static ssize_t fsl_qspi_nor_write(struct fsl_qspi *q, struct spi_nor *nor,
- u8 opcode, unsigned int to, u32 *txbuf,
- unsigned count)
-{
- int ret, i, j;
- u32 tmp;
-
- dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len : %d\n",
- q->chip_base_addr, to, count);
-
- /* clear the TX FIFO. */
- tmp = qspi_readl(q, q->iobase + QUADSPI_MCR);
- qspi_writel(q, tmp | QUADSPI_MCR_CLR_TXF_MASK, q->iobase + QUADSPI_MCR);
-
- /* fill the TX data to the FIFO */
- for (j = 0, i = ((count + 3) / 4); j < i; j++) {
- tmp = fsl_qspi_endian_xchg(q, *txbuf);
- qspi_writel(q, tmp, q->iobase + QUADSPI_TBDR);
- txbuf++;
- }
-
- /* fill the TXFIFO upto 16 bytes for i.MX7d */
- if (needs_fill_txfifo(q))
- for (; i < 4; i++)
- qspi_writel(q, tmp, q->iobase + QUADSPI_TBDR);
-
- /* Trigger it */
- ret = fsl_qspi_runcmd(q, opcode, to, count);
-
- if (ret == 0)
- return count;
-
- return ret;
-}
-
-static void fsl_qspi_set_map_addr(struct fsl_qspi *q)
-{
- int nor_size = q->nor_size;
- void __iomem *base = q->iobase;
-
- qspi_writel(q, nor_size + q->memmap_phy, base + QUADSPI_SFA1AD);
- qspi_writel(q, nor_size * 2 + q->memmap_phy, base + QUADSPI_SFA2AD);
- qspi_writel(q, nor_size * 3 + q->memmap_phy, base + QUADSPI_SFB1AD);
- qspi_writel(q, nor_size * 4 + q->memmap_phy, base + QUADSPI_SFB2AD);
-}
-
-/*
- * There are two different ways to read out the data from the flash:
- * the "IP Command Read" and the "AHB Command Read".
- *
- * The IC guy suggests we use the "AHB Command Read" which is faster
- * then the "IP Command Read". (What's more is that there is a bug in
- * the "IP Command Read" in the Vybrid.)
- *
- * After we set up the registers for the "AHB Command Read", we can use
- * the memcpy to read the data directly. A "missed" access to the buffer
- * causes the controller to clear the buffer, and use the sequence pointed
- * by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash.
- */
-static int fsl_qspi_init_ahb_read(struct fsl_qspi *q)
-{
- void __iomem *base = q->iobase;
- int seqid;
-
- /* AHB configuration for access buffer 0/1/2 .*/
- qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF0CR);
- qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF1CR);
- qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF2CR);
- /*
- * Set ADATSZ with the maximum AHB buffer size to improve the
- * read performance.
- */
- qspi_writel(q, QUADSPI_BUF3CR_ALLMST_MASK |
- ((q->devtype_data->ahb_buf_size / 8)
- << QUADSPI_BUF3CR_ADATSZ_SHIFT),
- base + QUADSPI_BUF3CR);
-
- /* We only use the buffer3 */
- qspi_writel(q, 0, base + QUADSPI_BUF0IND);
- qspi_writel(q, 0, base + QUADSPI_BUF1IND);
- qspi_writel(q, 0, base + QUADSPI_BUF2IND);
-
- /* Set the default lut sequence for AHB Read. */
- seqid = fsl_qspi_get_seqid(q, q->nor[0].read_opcode);
- if (seqid < 0)
- return seqid;
-
- qspi_writel(q, seqid << QUADSPI_BFGENCR_SEQID_SHIFT,
- q->iobase + QUADSPI_BFGENCR);
-
- return 0;
-}
-
-/* This function was used to prepare and enable QSPI clock */
-static int fsl_qspi_clk_prep_enable(struct fsl_qspi *q)
-{
- int ret;
-
- ret = clk_prepare_enable(q->clk_en);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(q->clk);
- if (ret) {
- clk_disable_unprepare(q->clk_en);
- return ret;
- }
-
- if (needs_wakeup_wait_mode(q))
- pm_qos_add_request(&q->pm_qos_req, PM_QOS_CPU_DMA_LATENCY, 0);
-
- return 0;
-}
-
-/* This function was used to disable and unprepare QSPI clock */
-static void fsl_qspi_clk_disable_unprep(struct fsl_qspi *q)
-{
- if (needs_wakeup_wait_mode(q))
- pm_qos_remove_request(&q->pm_qos_req);
-
- clk_disable_unprepare(q->clk);
- clk_disable_unprepare(q->clk_en);
-
-}
-
-/* We use this function to do some basic init for spi_nor_scan(). */
-static int fsl_qspi_nor_setup(struct fsl_qspi *q)
-{
- void __iomem *base = q->iobase;
- u32 reg;
- int ret;
-
- /* disable and unprepare clock to avoid glitch pass to controller */
- fsl_qspi_clk_disable_unprep(q);
-
- /* the default frequency, we will change it in the future. */
- ret = clk_set_rate(q->clk, 66000000);
- if (ret)
- return ret;
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- return ret;
-
- /* Reset the module */
- qspi_writel(q, QUADSPI_MCR_SWRSTSD_MASK | QUADSPI_MCR_SWRSTHD_MASK,
- base + QUADSPI_MCR);
- udelay(1);
-
- /* Init the LUT table. */
- fsl_qspi_init_lut(q);
-
- /* Disable the module */
- qspi_writel(q, QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK,
- base + QUADSPI_MCR);
-
- reg = qspi_readl(q, base + QUADSPI_SMPR);
- qspi_writel(q, reg & ~(QUADSPI_SMPR_FSDLY_MASK
- | QUADSPI_SMPR_FSPHS_MASK
- | QUADSPI_SMPR_HSENA_MASK
- | QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR);
-
- /* Enable the module */
- qspi_writel(q, QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK,
- base + QUADSPI_MCR);
-
- /* clear all interrupt status */
- qspi_writel(q, 0xffffffff, q->iobase + QUADSPI_FR);
-
- /* enable the interrupt */
- qspi_writel(q, QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER);
-
- return 0;
-}
-
-static int fsl_qspi_nor_setup_last(struct fsl_qspi *q)
-{
- unsigned long rate = q->clk_rate;
- int ret;
-
- if (needs_4x_clock(q))
- rate *= 4;
-
- /* disable and unprepare clock to avoid glitch pass to controller */
- fsl_qspi_clk_disable_unprep(q);
-
- ret = clk_set_rate(q->clk, rate);
- if (ret)
- return ret;
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- return ret;
-
- /* Init the LUT table again. */
- fsl_qspi_init_lut(q);
-
- /* Init for AHB read */
- return fsl_qspi_init_ahb_read(q);
-}
-
-static const struct of_device_id fsl_qspi_dt_ids[] = {
- { .compatible = "fsl,vf610-qspi", .data = &vybrid_data, },
- { .compatible = "fsl,imx6sx-qspi", .data = &imx6sx_data, },
- { .compatible = "fsl,imx7d-qspi", .data = &imx7d_data, },
- { .compatible = "fsl,imx6ul-qspi", .data = &imx6ul_data, },
- { .compatible = "fsl,ls1021a-qspi", .data = (void *)&ls1021a_data, },
- { .compatible = "fsl,ls2080a-qspi", .data = &ls2080a_data, },
- { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids);
-
-static void fsl_qspi_set_base_addr(struct fsl_qspi *q, struct spi_nor *nor)
-{
- q->chip_base_addr = q->nor_size * (nor - q->nor);
-}
-
-static int fsl_qspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
-{
- int ret;
- struct fsl_qspi *q = nor->priv;
-
- ret = fsl_qspi_runcmd(q, opcode, 0, len);
- if (ret)
- return ret;
-
- fsl_qspi_read_data(q, len, buf);
- return 0;
-}
-
-static int fsl_qspi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
-{
- struct fsl_qspi *q = nor->priv;
- int ret;
-
- if (!buf) {
- ret = fsl_qspi_runcmd(q, opcode, 0, 1);
- if (ret)
- return ret;
-
- if (opcode == SPINOR_OP_CHIP_ERASE)
- fsl_qspi_invalid(q);
-
- } else if (len > 0) {
- ret = fsl_qspi_nor_write(q, nor, opcode, 0,
- (u32 *)buf, len);
- if (ret > 0)
- return 0;
- } else {
- dev_err(q->dev, "invalid cmd %d\n", opcode);
- ret = -EINVAL;
- }
-
- return ret;
-}
-
-static ssize_t fsl_qspi_write(struct spi_nor *nor, loff_t to,
- size_t len, const u_char *buf)
-{
- struct fsl_qspi *q = nor->priv;
- ssize_t ret = fsl_qspi_nor_write(q, nor, nor->program_opcode, to,
- (u32 *)buf, len);
-
- /* invalid the data in the AHB buffer. */
- fsl_qspi_invalid(q);
- return ret;
-}
-
-static ssize_t fsl_qspi_read(struct spi_nor *nor, loff_t from,
- size_t len, u_char *buf)
-{
- struct fsl_qspi *q = nor->priv;
- u8 cmd = nor->read_opcode;
-
- /* if necessary,ioremap buffer before AHB read, */
- if (!q->ahb_addr) {
- q->memmap_offs = q->chip_base_addr + from;
- q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
-
- q->ahb_addr = ioremap_nocache(
- q->memmap_phy + q->memmap_offs,
- q->memmap_len);
- if (!q->ahb_addr) {
- dev_err(q->dev, "ioremap failed\n");
- return -ENOMEM;
- }
- /* ioremap if the data requested is out of range */
- } else if (q->chip_base_addr + from < q->memmap_offs
- || q->chip_base_addr + from + len >
- q->memmap_offs + q->memmap_len) {
- iounmap(q->ahb_addr);
-
- q->memmap_offs = q->chip_base_addr + from;
- q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
- q->ahb_addr = ioremap_nocache(
- q->memmap_phy + q->memmap_offs,
- q->memmap_len);
- if (!q->ahb_addr) {
- dev_err(q->dev, "ioremap failed\n");
- return -ENOMEM;
- }
- }
-
- dev_dbg(q->dev, "cmd [%x],read from %p, len:%zd\n",
- cmd, q->ahb_addr + q->chip_base_addr + from - q->memmap_offs,
- len);
-
- /* Read out the data directly from the AHB buffer.*/
- memcpy(buf, q->ahb_addr + q->chip_base_addr + from - q->memmap_offs,
- len);
-
- return len;
-}
-
-static int fsl_qspi_erase(struct spi_nor *nor, loff_t offs)
-{
- struct fsl_qspi *q = nor->priv;
- int ret;
-
- dev_dbg(nor->dev, "%dKiB at 0x%08x:0x%08x\n",
- nor->mtd.erasesize / 1024, q->chip_base_addr, (u32)offs);
-
- ret = fsl_qspi_runcmd(q, nor->erase_opcode, offs, 0);
- if (ret)
- return ret;
-
- fsl_qspi_invalid(q);
- return 0;
-}
-
-static int fsl_qspi_prep(struct spi_nor *nor, enum spi_nor_ops ops)
-{
- struct fsl_qspi *q = nor->priv;
- int ret;
-
- mutex_lock(&q->lock);
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- goto err_mutex;
-
- fsl_qspi_set_base_addr(q, nor);
- return 0;
-
-err_mutex:
- mutex_unlock(&q->lock);
- return ret;
-}
-
-static void fsl_qspi_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
-{
- struct fsl_qspi *q = nor->priv;
-
- fsl_qspi_clk_disable_unprep(q);
- mutex_unlock(&q->lock);
-}
-
-static int fsl_qspi_probe(struct platform_device *pdev)
-{
- const struct spi_nor_hwcaps hwcaps = {
- .mask = SNOR_HWCAPS_READ_1_1_4 |
- SNOR_HWCAPS_PP,
- };
- struct device_node *np = pdev->dev.of_node;
- struct device *dev = &pdev->dev;
- struct fsl_qspi *q;
- struct resource *res;
- struct spi_nor *nor;
- struct mtd_info *mtd;
- int ret, i = 0;
-
- q = devm_kzalloc(dev, sizeof(*q), GFP_KERNEL);
- if (!q)
- return -ENOMEM;
-
- q->nor_num = of_get_child_count(dev->of_node);
- if (!q->nor_num || q->nor_num > FSL_QSPI_MAX_CHIP)
- return -ENODEV;
-
- q->dev = dev;
- q->devtype_data = of_device_get_match_data(dev);
- if (!q->devtype_data)
- return -ENODEV;
- platform_set_drvdata(pdev, q);
-
- /* find the resources */
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI");
- q->iobase = devm_ioremap_resource(dev, res);
- if (IS_ERR(q->iobase))
- return PTR_ERR(q->iobase);
-
- q->big_endian = of_property_read_bool(np, "big-endian");
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
- "QuadSPI-memory");
- if (!devm_request_mem_region(dev, res->start, resource_size(res),
- res->name)) {
- dev_err(dev, "can't request region for resource %pR\n", res);
- return -EBUSY;
- }
-
- q->memmap_phy = res->start;
-
- /* find the clocks */
- q->clk_en = devm_clk_get(dev, "qspi_en");
- if (IS_ERR(q->clk_en))
- return PTR_ERR(q->clk_en);
-
- q->clk = devm_clk_get(dev, "qspi");
- if (IS_ERR(q->clk))
- return PTR_ERR(q->clk);
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret) {
- dev_err(dev, "can not enable the clock\n");
- goto clk_failed;
- }
-
- /* find the irq */
- ret = platform_get_irq(pdev, 0);
- if (ret < 0) {
- dev_err(dev, "failed to get the irq: %d\n", ret);
- goto irq_failed;
- }
-
- ret = devm_request_irq(dev, ret,
- fsl_qspi_irq_handler, 0, pdev->name, q);
- if (ret) {
- dev_err(dev, "failed to request irq: %d\n", ret);
- goto irq_failed;
- }
-
- ret = fsl_qspi_nor_setup(q);
- if (ret)
- goto irq_failed;
-
- if (of_get_property(np, "fsl,qspi-has-second-chip", NULL))
- q->has_second_chip = true;
-
- mutex_init(&q->lock);
-
- /* iterate the subnodes. */
- for_each_available_child_of_node(dev->of_node, np) {
- /* skip the holes */
- if (!q->has_second_chip)
- i *= 2;
-
- nor = &q->nor[i];
- mtd = &nor->mtd;
-
- nor->dev = dev;
- spi_nor_set_flash_node(nor, np);
- nor->priv = q;
-
- if (q->nor_num > 1 && !mtd->name) {
- int spiflash_idx;
-
- ret = of_property_read_u32(np, "reg", &spiflash_idx);
- if (!ret) {
- mtd->name = devm_kasprintf(dev, GFP_KERNEL,
- "%s-%d",
- dev_name(dev),
- spiflash_idx);
- if (!mtd->name) {
- ret = -ENOMEM;
- goto mutex_failed;
- }
- } else {
- dev_warn(dev, "reg property is missing\n");
- }
- }
-
- /* fill the hooks */
- nor->read_reg = fsl_qspi_read_reg;
- nor->write_reg = fsl_qspi_write_reg;
- nor->read = fsl_qspi_read;
- nor->write = fsl_qspi_write;
- nor->erase = fsl_qspi_erase;
-
- nor->prepare = fsl_qspi_prep;
- nor->unprepare = fsl_qspi_unprep;
-
- ret = of_property_read_u32(np, "spi-max-frequency",
- &q->clk_rate);
- if (ret < 0)
- goto mutex_failed;
-
- /* set the chip address for READID */
- fsl_qspi_set_base_addr(q, nor);
-
- ret = spi_nor_scan(nor, NULL, &hwcaps);
- if (ret)
- goto mutex_failed;
-
- ret = mtd_device_register(mtd, NULL, 0);
- if (ret)
- goto mutex_failed;
-
- /* Set the correct NOR size now. */
- if (q->nor_size == 0) {
- q->nor_size = mtd->size;
-
- /* Map the SPI NOR to accessiable address */
- fsl_qspi_set_map_addr(q);
- }
-
- /*
- * The TX FIFO is 64 bytes in the Vybrid, but the Page Program
- * may writes 265 bytes per time. The write is working in the
- * unit of the TX FIFO, not in the unit of the SPI NOR's page
- * size.
- *
- * So shrink the spi_nor->page_size if it is larger then the
- * TX FIFO.
- */
- if (nor->page_size > q->devtype_data->txfifo)
- nor->page_size = q->devtype_data->txfifo;
-
- i++;
- }
-
- /* finish the rest init. */
- ret = fsl_qspi_nor_setup_last(q);
- if (ret)
- goto last_init_failed;
-
- fsl_qspi_clk_disable_unprep(q);
- return 0;
-
-last_init_failed:
- for (i = 0; i < q->nor_num; i++) {
- /* skip the holes */
- if (!q->has_second_chip)
- i *= 2;
- mtd_device_unregister(&q->nor[i].mtd);
- }
-mutex_failed:
- mutex_destroy(&q->lock);
-irq_failed:
- fsl_qspi_clk_disable_unprep(q);
-clk_failed:
- dev_err(dev, "Freescale QuadSPI probe failed\n");
- return ret;
-}
-
-static int fsl_qspi_remove(struct platform_device *pdev)
-{
- struct fsl_qspi *q = platform_get_drvdata(pdev);
- int i;
-
- for (i = 0; i < q->nor_num; i++) {
- /* skip the holes */
- if (!q->has_second_chip)
- i *= 2;
- mtd_device_unregister(&q->nor[i].mtd);
- }
-
- /* disable the hardware */
- qspi_writel(q, QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR);
- qspi_writel(q, 0x0, q->iobase + QUADSPI_RSER);
-
- mutex_destroy(&q->lock);
-
- if (q->ahb_addr)
- iounmap(q->ahb_addr);
-
- return 0;
-}
-
-static int fsl_qspi_suspend(struct platform_device *pdev, pm_message_t state)
-{
- return 0;
-}
-
-static int fsl_qspi_resume(struct platform_device *pdev)
-{
- int ret;
- struct fsl_qspi *q = platform_get_drvdata(pdev);
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- return ret;
-
- fsl_qspi_nor_setup(q);
- fsl_qspi_set_map_addr(q);
- fsl_qspi_nor_setup_last(q);
-
- fsl_qspi_clk_disable_unprep(q);
-
- return 0;
-}
-
-static struct platform_driver fsl_qspi_driver = {
- .driver = {
- .name = "fsl-quadspi",
- .of_match_table = fsl_qspi_dt_ids,
- },
- .probe = fsl_qspi_probe,
- .remove = fsl_qspi_remove,
- .suspend = fsl_qspi_suspend,
- .resume = fsl_qspi_resume,
-};
-module_platform_driver(fsl_qspi_driver);
-
-MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver");
-MODULE_AUTHOR("Freescale Semiconductor Inc.");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 9f89cb1..f761655 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -63,7 +63,7 @@
config SPI_ATH79
tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
- depends on ATH79 && GPIOLIB
+ depends on ATH79 || COMPILE_TEST
select SPI_BITBANG
help
This enables support for the SPI controller present on the
@@ -268,6 +268,27 @@
help
This enables Freescale i.MX LPSPI controllers in master mode.
+config SPI_FSL_QUADSPI
+ tristate "Freescale QSPI controller"
+ depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ This enables support for the Quad SPI controller in master mode.
+ Up to four flash chips can be connected on two buses with two
+ chipselects each.
+ This controller does not support generic SPI messages. It only
+ supports the high-level SPI memory interface.
+
+config SPI_NXP_FLEXSPI
+ tristate "NXP Flex SPI controller"
+ depends on ARCH_LAYERSCAPE || HAS_IOMEM
+ help
+ This enables support for the Flex SPI controller in master mode.
+ Up to four slave devices can be connected on two buses with two
+ chipselects each.
+ This controller does not support generic SPI messages and only
+ supports the high-level SPI memory interface.
+
config SPI_GPIO
tristate "GPIO-based bitbanging SPI Master"
depends on GPIOLIB || COMPILE_TEST
@@ -296,8 +317,7 @@
depends on ARCH_MXC || COMPILE_TEST
select SPI_BITBANG
help
- This enables using the Freescale i.MX SPI controllers in master
- mode.
+ This enables support for the Freescale i.MX SPI controllers.
config SPI_JCORE
tristate "J-Core SPI Master"
@@ -372,7 +392,7 @@
depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
help
This enables support for the Freescale DSPI controller in master
- mode. VF610 platform uses the controller.
+ mode. VF610, LS1021A and ColdFire platforms uses the controller.
config SPI_FSL_ESPI
tristate "Freescale eSPI controller"
@@ -631,6 +651,12 @@
help
SPI driver for SuperH HSPI blocks.
+config SPI_SIFIVE
+ tristate "SiFive SPI controller"
+ depends on HAS_IOMEM
+ help
+ This exposes the SPI controller IP from SiFive.
+
config SPI_SIRF
tristate "CSR SiRFprimaII SPI controller"
depends on SIRF_DMA
@@ -665,7 +691,7 @@
tristate "STMicroelectronics STM32 SPI controller"
depends on ARCH_STM32 || COMPILE_TEST
help
- SPI driver for STMicroelectonics STM32 SoCs.
+ SPI driver for STMicroelectronics STM32 SoCs.
STM32 SPI controller supports DMA and PIO modes. When DMA
is not available, the driver automatically falls back to
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index f296270..d8fc03c 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -45,6 +45,7 @@
obj-$(CONFIG_SPI_FSL_LIB) += spi-fsl-lib.o
obj-$(CONFIG_SPI_FSL_ESPI) += spi-fsl-espi.o
obj-$(CONFIG_SPI_FSL_LPSPI) += spi-fsl-lpspi.o
+obj-$(CONFIG_SPI_FSL_QUADSPI) += spi-fsl-qspi.o
obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o
obj-$(CONFIG_SPI_GPIO) += spi-gpio.o
obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o
@@ -63,6 +64,7 @@
obj-$(CONFIG_SPI_MXS) += spi-mxs.o
obj-$(CONFIG_SPI_NPCM_PSPI) += spi-npcm-pspi.o
obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o
+obj-$(CONFIG_SPI_NXP_FLEXSPI) += spi-nxp-fspi.o
obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o
spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o
obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o
@@ -93,6 +95,7 @@
obj-$(CONFIG_SPI_SH_HSPI) += spi-sh-hspi.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi-sh-msiof.o
obj-$(CONFIG_SPI_SH_SCI) += spi-sh-sci.o
+obj-$(CONFIG_SPI_SIFIVE) += spi-sifive.o
obj-$(CONFIG_SPI_SIRF) += spi-sirf.o
obj-$(CONFIG_SPI_SLAVE_MT27XX) += spi-slave-mt27xx.o
obj-$(CONFIG_SPI_SPRD) += spi-sprd.o
diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c
index ddc7124..fffc21c 100644
--- a/drivers/spi/atmel-quadspi.c
+++ b/drivers/spi/atmel-quadspi.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/*
* Driver for Atmel QSPI Controller
*
@@ -7,31 +8,19 @@
* Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
* Author: Piotr Bugalski <bugalski.piotr@gmail.com>
*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program. If not, see <http://www.gnu.org/licenses/>.
- *
* This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale.
*/
-#include <linux/kernel.h>
#include <linux/clk.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/interrupt.h>
-#include <linux/of.h>
-
#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
#include <linux/spi/spi-mem.h>
/* QSPI register offsets */
@@ -47,7 +36,9 @@
#define QSPI_IAR 0x0030 /* Instruction Address Register */
#define QSPI_ICR 0x0034 /* Instruction Code Register */
+#define QSPI_WICR 0x0034 /* Write Instruction Code Register */
#define QSPI_IFR 0x0038 /* Instruction Frame Register */
+#define QSPI_RICR 0x003C /* Read Instruction Code Register */
#define QSPI_SMR 0x0040 /* Scrambling Mode Register */
#define QSPI_SKR 0x0044 /* Scrambling Key Register */
@@ -100,7 +91,7 @@
#define QSPI_SCR_DLYBS_MASK GENMASK(23, 16)
#define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK)
-/* Bitfields in QSPI_ICR (Instruction Code Register) */
+/* Bitfields in QSPI_ICR (Read/Write Instruction Code Register) */
#define QSPI_ICR_INST_MASK GENMASK(7, 0)
#define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK)
#define QSPI_ICR_OPT_MASK GENMASK(23, 16)
@@ -125,14 +116,12 @@
#define QSPI_IFR_OPTL_4BIT (2 << 8)
#define QSPI_IFR_OPTL_8BIT (3 << 8)
#define QSPI_IFR_ADDRL BIT(10)
-#define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12)
-#define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12)
-#define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12)
-#define QSPI_IFR_TFRTYP_TRSFR_WRITE (2 << 12)
-#define QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM (3 << 13)
+#define QSPI_IFR_TFRTYP_MEM BIT(12)
+#define QSPI_IFR_SAMA5D2_WRITE_TRSFR BIT(13)
#define QSPI_IFR_CRM BIT(14)
#define QSPI_IFR_NBDUM_MASK GENMASK(20, 16)
#define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK)
+#define QSPI_IFR_APBTFRTYP_READ BIT(24) /* Defined in SAM9X60 */
/* Bitfields in QSPI_SMR (Scrambling Mode Register) */
#define QSPI_SMR_SCREN BIT(0)
@@ -148,24 +137,31 @@
#define QSPI_WPSR_WPVSRC_MASK GENMASK(15, 8)
#define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC)
+struct atmel_qspi_caps {
+ bool has_qspick;
+ bool has_ricr;
+};
struct atmel_qspi {
void __iomem *regs;
void __iomem *mem;
- struct clk *clk;
+ struct clk *pclk;
+ struct clk *qspick;
struct platform_device *pdev;
+ const struct atmel_qspi_caps *caps;
u32 pending;
+ u32 mr;
struct completion cmd_completion;
};
-struct qspi_mode {
+struct atmel_qspi_mode {
u8 cmd_buswidth;
u8 addr_buswidth;
u8 data_buswidth;
u32 config;
};
-static const struct qspi_mode sama5d2_qspi_modes[] = {
+static const struct atmel_qspi_mode atmel_qspi_modes[] = {
{ 1, 1, 1, QSPI_IFR_WIDTH_SINGLE_BIT_SPI },
{ 1, 1, 2, QSPI_IFR_WIDTH_DUAL_OUTPUT },
{ 1, 1, 4, QSPI_IFR_WIDTH_QUAD_OUTPUT },
@@ -175,19 +171,8 @@
{ 4, 4, 4, QSPI_IFR_WIDTH_QUAD_CMD },
};
-/* Register access functions */
-static inline u32 qspi_readl(struct atmel_qspi *aq, u32 reg)
-{
- return readl_relaxed(aq->regs + reg);
-}
-
-static inline void qspi_writel(struct atmel_qspi *aq, u32 reg, u32 value)
-{
- writel_relaxed(value, aq->regs + reg);
-}
-
-static inline bool is_compatible(const struct spi_mem_op *op,
- const struct qspi_mode *mode)
+static inline bool atmel_qspi_is_compatible(const struct spi_mem_op *op,
+ const struct atmel_qspi_mode *mode)
{
if (op->cmd.buswidth != mode->cmd_buswidth)
return false;
@@ -201,21 +186,21 @@
return true;
}
-static int find_mode(const struct spi_mem_op *op)
+static int atmel_qspi_find_mode(const struct spi_mem_op *op)
{
u32 i;
- for (i = 0; i < ARRAY_SIZE(sama5d2_qspi_modes); i++)
- if (is_compatible(op, &sama5d2_qspi_modes[i]))
+ for (i = 0; i < ARRAY_SIZE(atmel_qspi_modes); i++)
+ if (atmel_qspi_is_compatible(op, &atmel_qspi_modes[i]))
return i;
- return -1;
+ return -ENOTSUPP;
}
static bool atmel_qspi_supports_op(struct spi_mem *mem,
const struct spi_mem_op *op)
{
- if (find_mode(op) < 0)
+ if (atmel_qspi_find_mode(op) < 0)
return false;
/* special case not supported by hardware */
@@ -226,29 +211,37 @@
return true;
}
-static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+static int atmel_qspi_set_cfg(struct atmel_qspi *aq,
+ const struct spi_mem_op *op, u32 *offset)
{
- struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->master);
- int mode;
+ u32 iar, icr, ifr;
u32 dummy_cycles = 0;
- u32 iar, icr, ifr, sr;
- int err = 0;
+ int mode;
iar = 0;
icr = QSPI_ICR_INST(op->cmd.opcode);
ifr = QSPI_IFR_INSTEN;
- qspi_writel(aq, QSPI_MR, QSPI_MR_SMM);
-
- mode = find_mode(op);
+ mode = atmel_qspi_find_mode(op);
if (mode < 0)
- return -ENOTSUPP;
-
- ifr |= sama5d2_qspi_modes[mode].config;
+ return mode;
+ ifr |= atmel_qspi_modes[mode].config;
if (op->dummy.buswidth && op->dummy.nbytes)
dummy_cycles = op->dummy.nbytes * 8 / op->dummy.buswidth;
+ /*
+ * The controller allows 24 and 32-bit addressing while NAND-flash
+ * requires 16-bit long. Handling 8-bit long addresses is done using
+ * the option field. For the 16-bit addresses, the workaround depends
+ * of the number of requested dummy bits. If there are 8 or more dummy
+ * cycles, the address is shifted and sent with the first dummy byte.
+ * Otherwise opcode is disabled and the first byte of the address
+ * contains the command opcode (works only if the opcode and address
+ * use the same buswidth). The limitation is when the 16-bit address is
+ * used without enough dummy cycles and the opcode is using a different
+ * buswidth than the address.
+ */
if (op->addr.buswidth) {
switch (op->addr.nbytes) {
case 0:
@@ -282,6 +275,9 @@
}
}
+ /* offset of the data access in the QSPI memory space */
+ *offset = iar;
+
/* Set number of dummy cycles */
if (dummy_cycles)
ifr |= QSPI_IFR_NBDUM(dummy_cycles);
@@ -290,49 +286,82 @@
if (op->data.nbytes)
ifr |= QSPI_IFR_DATAEN;
- if (op->data.dir == SPI_MEM_DATA_IN && op->data.nbytes)
- ifr |= QSPI_IFR_TFRTYP_TRSFR_READ;
- else
- ifr |= QSPI_IFR_TFRTYP_TRSFR_WRITE;
+ /*
+ * If the QSPI controller is set in regular SPI mode, set it in
+ * Serial Memory Mode (SMM).
+ */
+ if (aq->mr != QSPI_MR_SMM) {
+ writel_relaxed(QSPI_MR_SMM, aq->regs + QSPI_MR);
+ aq->mr = QSPI_MR_SMM;
+ }
/* Clear pending interrupts */
- (void)qspi_readl(aq, QSPI_SR);
+ (void)readl_relaxed(aq->regs + QSPI_SR);
- /* Set QSPI Instruction Frame registers */
- qspi_writel(aq, QSPI_IAR, iar);
- qspi_writel(aq, QSPI_ICR, icr);
- qspi_writel(aq, QSPI_IFR, ifr);
+ if (aq->caps->has_ricr) {
+ if (!op->addr.nbytes && op->data.dir == SPI_MEM_DATA_IN)
+ ifr |= QSPI_IFR_APBTFRTYP_READ;
+
+ /* Set QSPI Instruction Frame registers */
+ writel_relaxed(iar, aq->regs + QSPI_IAR);
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ writel_relaxed(icr, aq->regs + QSPI_RICR);
+ else
+ writel_relaxed(icr, aq->regs + QSPI_WICR);
+ writel_relaxed(ifr, aq->regs + QSPI_IFR);
+ } else {
+ if (op->data.dir == SPI_MEM_DATA_OUT)
+ ifr |= QSPI_IFR_SAMA5D2_WRITE_TRSFR;
+
+ /* Set QSPI Instruction Frame registers */
+ writel_relaxed(iar, aq->regs + QSPI_IAR);
+ writel_relaxed(icr, aq->regs + QSPI_ICR);
+ writel_relaxed(ifr, aq->regs + QSPI_IFR);
+ }
+
+ return 0;
+}
+
+static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->master);
+ u32 sr, offset;
+ int err;
+
+ err = atmel_qspi_set_cfg(aq, op, &offset);
+ if (err)
+ return err;
/* Skip to the final steps if there is no data */
if (op->data.nbytes) {
/* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
- (void)qspi_readl(aq, QSPI_IFR);
+ (void)readl_relaxed(aq->regs + QSPI_IFR);
/* Send/Receive data */
if (op->data.dir == SPI_MEM_DATA_IN)
- _memcpy_fromio(op->data.buf.in,
- aq->mem + iar, op->data.nbytes);
+ _memcpy_fromio(op->data.buf.in, aq->mem + offset,
+ op->data.nbytes);
else
- _memcpy_toio(aq->mem + iar,
- op->data.buf.out, op->data.nbytes);
+ _memcpy_toio(aq->mem + offset, op->data.buf.out,
+ op->data.nbytes);
/* Release the chip-select */
- qspi_writel(aq, QSPI_CR, QSPI_CR_LASTXFER);
+ writel_relaxed(QSPI_CR_LASTXFER, aq->regs + QSPI_CR);
}
/* Poll INSTRuction End status */
- sr = qspi_readl(aq, QSPI_SR);
+ sr = readl_relaxed(aq->regs + QSPI_SR);
if ((sr & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED)
return err;
/* Wait for INSTRuction End interrupt */
reinit_completion(&aq->cmd_completion);
aq->pending = sr & QSPI_SR_CMD_COMPLETED;
- qspi_writel(aq, QSPI_IER, QSPI_SR_CMD_COMPLETED);
+ writel_relaxed(QSPI_SR_CMD_COMPLETED, aq->regs + QSPI_IER);
if (!wait_for_completion_timeout(&aq->cmd_completion,
msecs_to_jiffies(1000)))
err = -ETIMEDOUT;
- qspi_writel(aq, QSPI_IDR, QSPI_SR_CMD_COMPLETED);
+ writel_relaxed(QSPI_SR_CMD_COMPLETED, aq->regs + QSPI_IDR);
return err;
}
@@ -361,7 +390,7 @@
if (!spi->max_speed_hz)
return -EINVAL;
- src_rate = clk_get_rate(aq->clk);
+ src_rate = clk_get_rate(aq->pclk);
if (!src_rate)
return -EINVAL;
@@ -371,7 +400,7 @@
scbr--;
scr = QSPI_SCR_SCBR(scbr);
- qspi_writel(aq, QSPI_SCR, scr);
+ writel_relaxed(scr, aq->regs + QSPI_SCR);
return 0;
}
@@ -379,21 +408,25 @@
static int atmel_qspi_init(struct atmel_qspi *aq)
{
/* Reset the QSPI controller */
- qspi_writel(aq, QSPI_CR, QSPI_CR_SWRST);
+ writel_relaxed(QSPI_CR_SWRST, aq->regs + QSPI_CR);
+
+ /* Set the QSPI controller by default in Serial Memory Mode */
+ writel_relaxed(QSPI_MR_SMM, aq->regs + QSPI_MR);
+ aq->mr = QSPI_MR_SMM;
/* Enable the QSPI controller */
- qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIEN);
+ writel_relaxed(QSPI_CR_QSPIEN, aq->regs + QSPI_CR);
return 0;
}
static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id)
{
- struct atmel_qspi *aq = (struct atmel_qspi *)dev_id;
+ struct atmel_qspi *aq = dev_id;
u32 status, mask, pending;
- status = qspi_readl(aq, QSPI_SR);
- mask = qspi_readl(aq, QSPI_IMR);
+ status = readl_relaxed(aq->regs + QSPI_SR);
+ mask = readl_relaxed(aq->regs + QSPI_IMR);
pending = status & mask;
if (!pending)
@@ -449,44 +482,74 @@
}
/* Get the peripheral clock */
- aq->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(aq->clk)) {
+ aq->pclk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(aq->pclk))
+ aq->pclk = devm_clk_get(&pdev->dev, NULL);
+
+ if (IS_ERR(aq->pclk)) {
dev_err(&pdev->dev, "missing peripheral clock\n");
- err = PTR_ERR(aq->clk);
+ err = PTR_ERR(aq->pclk);
goto exit;
}
/* Enable the peripheral clock */
- err = clk_prepare_enable(aq->clk);
+ err = clk_prepare_enable(aq->pclk);
if (err) {
dev_err(&pdev->dev, "failed to enable the peripheral clock\n");
goto exit;
}
+ aq->caps = of_device_get_match_data(&pdev->dev);
+ if (!aq->caps) {
+ dev_err(&pdev->dev, "Could not retrieve QSPI caps\n");
+ err = -EINVAL;
+ goto exit;
+ }
+
+ if (aq->caps->has_qspick) {
+ /* Get the QSPI system clock */
+ aq->qspick = devm_clk_get(&pdev->dev, "qspick");
+ if (IS_ERR(aq->qspick)) {
+ dev_err(&pdev->dev, "missing system clock\n");
+ err = PTR_ERR(aq->qspick);
+ goto disable_pclk;
+ }
+
+ /* Enable the QSPI system clock */
+ err = clk_prepare_enable(aq->qspick);
+ if (err) {
+ dev_err(&pdev->dev,
+ "failed to enable the QSPI system clock\n");
+ goto disable_pclk;
+ }
+ }
+
/* Request the IRQ */
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(&pdev->dev, "missing IRQ\n");
err = irq;
- goto disable_clk;
+ goto disable_qspick;
}
err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt,
0, dev_name(&pdev->dev), aq);
if (err)
- goto disable_clk;
+ goto disable_qspick;
err = atmel_qspi_init(aq);
if (err)
- goto disable_clk;
+ goto disable_qspick;
err = spi_register_controller(ctrl);
if (err)
- goto disable_clk;
+ goto disable_qspick;
return 0;
-disable_clk:
- clk_disable_unprepare(aq->clk);
+disable_qspick:
+ clk_disable_unprepare(aq->qspick);
+disable_pclk:
+ clk_disable_unprepare(aq->pclk);
exit:
spi_controller_put(ctrl);
@@ -499,8 +562,9 @@
struct atmel_qspi *aq = spi_controller_get_devdata(ctrl);
spi_unregister_controller(ctrl);
- qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIDIS);
- clk_disable_unprepare(aq->clk);
+ writel_relaxed(QSPI_CR_QSPIDIS, aq->regs + QSPI_CR);
+ clk_disable_unprepare(aq->qspick);
+ clk_disable_unprepare(aq->pclk);
return 0;
}
@@ -508,7 +572,8 @@
{
struct atmel_qspi *aq = dev_get_drvdata(dev);
- clk_disable_unprepare(aq->clk);
+ clk_disable_unprepare(aq->qspick);
+ clk_disable_unprepare(aq->pclk);
return 0;
}
@@ -517,7 +582,8 @@
{
struct atmel_qspi *aq = dev_get_drvdata(dev);
- clk_prepare_enable(aq->clk);
+ clk_prepare_enable(aq->pclk);
+ clk_prepare_enable(aq->qspick);
return atmel_qspi_init(aq);
}
@@ -525,8 +591,22 @@
static SIMPLE_DEV_PM_OPS(atmel_qspi_pm_ops, atmel_qspi_suspend,
atmel_qspi_resume);
+static const struct atmel_qspi_caps atmel_sama5d2_qspi_caps = {};
+
+static const struct atmel_qspi_caps atmel_sam9x60_qspi_caps = {
+ .has_qspick = true,
+ .has_ricr = true,
+};
+
static const struct of_device_id atmel_qspi_dt_ids[] = {
- { .compatible = "atmel,sama5d2-qspi" },
+ {
+ .compatible = "atmel,sama5d2-qspi",
+ .data = &atmel_sama5d2_qspi_caps,
+ },
+ {
+ .compatible = "microchip,sam9x60-qspi",
+ .data = &atmel_sam9x60_qspi_caps,
+ },
{ /* sentinel */ }
};
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index 3f6b657..847f354 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -21,18 +21,26 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/bitops.h>
-#include <linux/gpio.h>
#include <linux/clk.h>
#include <linux/err.h>
-
-#include <asm/mach-ath79/ar71xx_regs.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
#define DRV_NAME "ath79-spi"
#define ATH79_SPI_RRW_DELAY_FACTOR 12000
#define MHZ (1000 * 1000)
+#define AR71XX_SPI_REG_FS 0x00 /* Function Select */
+#define AR71XX_SPI_REG_CTRL 0x04 /* SPI Control */
+#define AR71XX_SPI_REG_IOC 0x08 /* SPI I/O Control */
+#define AR71XX_SPI_REG_RDS 0x0c /* Read Data Shift */
+
+#define AR71XX_SPI_FS_GPIO BIT(0) /* Enable GPIO mode */
+
+#define AR71XX_SPI_IOC_DO BIT(0) /* Data Out pin */
+#define AR71XX_SPI_IOC_CLK BIT(8) /* CLK pin */
+#define AR71XX_SPI_IOC_CS(n) BIT(16 + (n))
+
struct ath79_spi {
struct spi_bitbang bitbang;
u32 ioc_base;
@@ -67,31 +75,14 @@
{
struct ath79_spi *sp = ath79_spidev_to_sp(spi);
int cs_high = (spi->mode & SPI_CS_HIGH) ? is_active : !is_active;
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
- if (is_active) {
- /* set initial clock polarity */
- if (spi->mode & SPI_CPOL)
- sp->ioc_base |= AR71XX_SPI_IOC_CLK;
- else
- sp->ioc_base &= ~AR71XX_SPI_IOC_CLK;
+ if (cs_high)
+ sp->ioc_base |= cs_bit;
+ else
+ sp->ioc_base &= ~cs_bit;
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
- if (gpio_is_valid(spi->cs_gpio)) {
- /* SPI is normally active-low */
- gpio_set_value_cansleep(spi->cs_gpio, cs_high);
- } else {
- u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
- if (cs_high)
- sp->ioc_base |= cs_bit;
- else
- sp->ioc_base &= ~cs_bit;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
+ ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
static void ath79_spi_enable(struct ath79_spi *sp)
@@ -103,6 +94,9 @@
sp->reg_ctrl = ath79_spi_rr(sp, AR71XX_SPI_REG_CTRL);
sp->ioc_base = ath79_spi_rr(sp, AR71XX_SPI_REG_IOC);
+ /* clear clk and mosi in the base state */
+ sp->ioc_base &= ~(AR71XX_SPI_IOC_DO | AR71XX_SPI_IOC_CLK);
+
/* TODO: setup speed? */
ath79_spi_wr(sp, AR71XX_SPI_REG_CTRL, 0x43);
}
@@ -115,66 +109,6 @@
ath79_spi_wr(sp, AR71XX_SPI_REG_FS, 0);
}
-static int ath79_spi_setup_cs(struct spi_device *spi)
-{
- struct ath79_spi *sp = ath79_spidev_to_sp(spi);
- int status;
-
- status = 0;
- if (gpio_is_valid(spi->cs_gpio)) {
- unsigned long flags;
-
- flags = GPIOF_DIR_OUT;
- if (spi->mode & SPI_CS_HIGH)
- flags |= GPIOF_INIT_LOW;
- else
- flags |= GPIOF_INIT_HIGH;
-
- status = gpio_request_one(spi->cs_gpio, flags,
- dev_name(&spi->dev));
- } else {
- u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
- if (spi->mode & SPI_CS_HIGH)
- sp->ioc_base &= ~cs_bit;
- else
- sp->ioc_base |= cs_bit;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
- return status;
-}
-
-static void ath79_spi_cleanup_cs(struct spi_device *spi)
-{
- if (gpio_is_valid(spi->cs_gpio))
- gpio_free(spi->cs_gpio);
-}
-
-static int ath79_spi_setup(struct spi_device *spi)
-{
- int status = 0;
-
- if (!spi->controller_state) {
- status = ath79_spi_setup_cs(spi);
- if (status)
- return status;
- }
-
- status = spi_bitbang_setup(spi);
- if (status && !spi->controller_state)
- ath79_spi_cleanup_cs(spi);
-
- return status;
-}
-
-static void ath79_spi_cleanup(struct spi_device *spi)
-{
- ath79_spi_cleanup_cs(spi);
- spi_bitbang_cleanup(spi);
-}
-
static u32 ath79_spi_txrx_mode0(struct spi_device *spi, unsigned int nsecs,
u32 word, u8 bits, unsigned flags)
{
@@ -225,9 +159,10 @@
pdata = dev_get_platdata(&pdev->dev);
+ master->use_gpio_descriptors = true;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
- master->setup = ath79_spi_setup;
- master->cleanup = ath79_spi_cleanup;
+ master->setup = spi_bitbang_setup;
+ master->cleanup = spi_bitbang_cleanup;
if (pdata) {
master->bus_num = pdata->bus_num;
master->num_chipselect = pdata->num_chipselect;
@@ -236,7 +171,6 @@
sp->bitbang.master = master;
sp->bitbang.chipselect = ath79_spi_chipselect;
sp->bitbang.txrx_word[SPI_MODE_0] = ath79_spi_txrx_mode0;
- sp->bitbang.setup_transfer = spi_bitbang_setup_transfer;
sp->bitbang.flags = SPI_CS_HIGH;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 74fddcd..4954f0a 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -23,8 +23,7 @@
#include <linux/of.h>
#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm_runtime.h>
@@ -312,7 +311,7 @@
/* Controller-specific per-slave state */
struct atmel_spi_device {
- unsigned int npcs_pin;
+ struct gpio_desc *npcs_pin;
u32 csr;
};
@@ -355,7 +354,6 @@
static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
- unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
if (atmel_spi_is_v2(as)) {
@@ -379,7 +377,7 @@
mr = spi_readl(as, MR);
if (as->use_cs_gpios)
- gpio_set_value(asd->npcs_pin, active);
+ gpiod_set_value(asd->npcs_pin, 1);
} else {
u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
int i;
@@ -396,19 +394,16 @@
mr = spi_readl(as, MR);
mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
if (as->use_cs_gpios && spi->chip_select != 0)
- gpio_set_value(asd->npcs_pin, active);
+ gpiod_set_value(asd->npcs_pin, 1);
spi_writel(as, MR, mr);
}
- dev_dbg(&spi->dev, "activate %u%s, mr %08x\n",
- asd->npcs_pin, active ? " (high)" : "",
- mr);
+ dev_dbg(&spi->dev, "activate NPCS, mr %08x\n", mr);
}
static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
- unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
/* only deactivate *this* device; sometimes transfers to
@@ -420,14 +415,12 @@
spi_writel(as, MR, mr);
}
- dev_dbg(&spi->dev, "DEactivate %u%s, mr %08x\n",
- asd->npcs_pin, active ? " (low)" : "",
- mr);
+ dev_dbg(&spi->dev, "DEactivate NPCS, mr %08x\n", mr);
if (!as->use_cs_gpios)
spi_writel(as, CR, SPI_BIT(LASTXFER));
else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
- gpio_set_value(asd->npcs_pin, !active);
+ gpiod_set_value(asd->npcs_pin, 0);
}
static void atmel_spi_lock(struct atmel_spi *as) __acquires(&as->lock)
@@ -1188,7 +1181,6 @@
struct atmel_spi_device *asd;
u32 csr;
unsigned int bits = spi->bits_per_word;
- unsigned int npcs_pin;
as = spi_master_get_devdata(spi->master);
@@ -1209,21 +1201,14 @@
csr |= SPI_BIT(CSAAT);
/* DLYBS is mostly irrelevant since we manage chipselect using GPIOs.
- *
- * DLYBCT would add delays between words, slowing down transfers.
- * It could potentially be useful to cope with DMA bottlenecks, but
- * in those cases it's probably best to just use a lower bitrate.
*/
csr |= SPI_BF(DLYBS, 0);
- csr |= SPI_BF(DLYBCT, 0);
- /* chipselect must have been muxed as GPIO (e.g. in board setup) */
- npcs_pin = (unsigned long)spi->controller_data;
-
- if (!as->use_cs_gpios)
- npcs_pin = spi->chip_select;
- else if (gpio_is_valid(spi->cs_gpio))
- npcs_pin = spi->cs_gpio;
+ /* DLYBCT adds delays between words. This is useful for slow devices
+ * that need a bit of time to setup the next transfer.
+ */
+ csr |= SPI_BF(DLYBCT,
+ (as->spi_clk / 1000000 * spi->word_delay_usecs) >> 5);
asd = spi->controller_state;
if (!asd) {
@@ -1231,11 +1216,21 @@
if (!asd)
return -ENOMEM;
- if (as->use_cs_gpios)
- gpio_direction_output(npcs_pin,
- !(spi->mode & SPI_CS_HIGH));
+ /*
+ * If use_cs_gpios is true this means that we have "cs-gpios"
+ * defined in the device tree node so we should have
+ * gotten the GPIO lines from the device tree inside the
+ * SPI core. Warn if this is not the case but continue since
+ * CS GPIOs are after all optional.
+ */
+ if (as->use_cs_gpios) {
+ if (!spi->cs_gpiod) {
+ dev_err(&spi->dev,
+ "host claims to use CS GPIOs but no CS found in DT by the SPI core\n");
+ }
+ asd->npcs_pin = spi->cs_gpiod;
+ }
- asd->npcs_pin = npcs_pin;
spi->controller_state = asd;
}
@@ -1473,41 +1468,6 @@
as->caps.has_pdc_support = version < 0x212;
}
-/*-------------------------------------------------------------------------*/
-static int atmel_spi_gpio_cs(struct platform_device *pdev)
-{
- struct spi_master *master = platform_get_drvdata(pdev);
- struct atmel_spi *as = spi_master_get_devdata(master);
- struct device_node *np = master->dev.of_node;
- int i;
- int ret = 0;
- int nb = 0;
-
- if (!as->use_cs_gpios)
- return 0;
-
- if (!np)
- return 0;
-
- nb = of_gpio_named_count(np, "cs-gpios");
- for (i = 0; i < nb; i++) {
- int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
- "cs-gpios", i);
-
- if (cs_gpio == -EPROBE_DEFER)
- return cs_gpio;
-
- if (gpio_is_valid(cs_gpio)) {
- ret = devm_gpio_request(&pdev->dev, cs_gpio,
- dev_name(&pdev->dev));
- if (ret)
- return ret;
- }
- }
-
- return 0;
-}
-
static void atmel_spi_init(struct atmel_spi *as)
{
spi_writel(as, CR, SPI_BIT(SWRST));
@@ -1560,6 +1520,7 @@
goto out_free;
/* the spi->mode bits understood by this driver: */
+ master->use_gpio_descriptors = true;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
master->dev.of_node = pdev->dev.of_node;
@@ -1592,6 +1553,11 @@
atmel_get_caps(as);
+ /*
+ * If there are chip selects in the device tree, those will be
+ * discovered by the SPI core when registering the SPI master
+ * and assigned to each SPI device.
+ */
as->use_cs_gpios = true;
if (atmel_spi_is_v2(as) &&
pdev->dev.of_node &&
@@ -1600,10 +1566,6 @@
master->num_chipselect = 4;
}
- ret = atmel_spi_gpio_cs(pdev);
- if (ret)
- goto out_unmap_regs;
-
as->use_dma = false;
as->use_pdc = false;
if (as->caps.has_dma_support) {
diff --git a/drivers/spi/spi-bcm2835aux.c b/drivers/spi/spi-bcm2835aux.c
index 671e374..f7e0548 100644
--- a/drivers/spi/spi-bcm2835aux.c
+++ b/drivers/spi/spi-bcm2835aux.c
@@ -456,7 +456,7 @@
}
bs->clk = devm_clk_get(&pdev->dev, NULL);
- if ((!bs->clk) || (IS_ERR(bs->clk))) {
+ if (IS_ERR(bs->clk)) {
err = PTR_ERR(bs->clk);
dev_err(&pdev->dev, "could not get clk: %d\n", err);
goto out_master_put;
diff --git a/drivers/spi/spi-bitbang.c b/drivers/spi/spi-bitbang.c
index f291760..dd9a8c54 100644
--- a/drivers/spi/spi-bitbang.c
+++ b/drivers/spi/spi-bitbang.c
@@ -213,19 +213,6 @@
dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
- /* NOTE we _need_ to call chipselect() early, ideally with adapter
- * setup, unless the hardware defaults cooperate to avoid confusion
- * between normal (active low) and inverted chipselects.
- */
-
- /* deselect chip (low or high) */
- mutex_lock(&bitbang->lock);
- if (!bitbang->busy) {
- bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
- ndelay(cs->nsecs);
- }
- mutex_unlock(&bitbang->lock);
-
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_setup);
diff --git a/drivers/spi/spi-cadence.c b/drivers/spi/spi-cadence.c
index 7c88f74..43d0e79 100644
--- a/drivers/spi/spi-cadence.c
+++ b/drivers/spi/spi-cadence.c
@@ -13,7 +13,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
@@ -128,10 +128,6 @@
u32 is_decoded_cs;
};
-struct cdns_spi_device_data {
- bool gpio_requested;
-};
-
/* Macros for the SPI controller read/write */
static inline u32 cdns_spi_read(struct cdns_spi *xspi, u32 offset)
{
@@ -176,16 +172,16 @@
/**
* cdns_spi_chipselect - Select or deselect the chip select line
* @spi: Pointer to the spi_device structure
- * @is_high: Select(0) or deselect (1) the chip select line
+ * @enable: Select (1) or deselect (0) the chip select line
*/
-static void cdns_spi_chipselect(struct spi_device *spi, bool is_high)
+static void cdns_spi_chipselect(struct spi_device *spi, bool enable)
{
struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
u32 ctrl_reg;
ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
- if (is_high) {
+ if (!enable) {
/* Deselect the slave */
ctrl_reg |= CDNS_SPI_CR_SSCTRL;
} else {
@@ -469,64 +465,6 @@
return 0;
}
-static int cdns_spi_setup(struct spi_device *spi)
-{
-
- int ret = -EINVAL;
- struct cdns_spi_device_data *cdns_spi_data = spi_get_ctldata(spi);
-
- /* this is a pin managed by the controller, leave it alone */
- if (spi->cs_gpio == -ENOENT)
- return 0;
-
- /* this seems to be the first time we're here */
- if (!cdns_spi_data) {
- cdns_spi_data = kzalloc(sizeof(*cdns_spi_data), GFP_KERNEL);
- if (!cdns_spi_data)
- return -ENOMEM;
- cdns_spi_data->gpio_requested = false;
- spi_set_ctldata(spi, cdns_spi_data);
- }
-
- /* if we haven't done so, grab the gpio */
- if (!cdns_spi_data->gpio_requested && gpio_is_valid(spi->cs_gpio)) {
- ret = gpio_request_one(spi->cs_gpio,
- (spi->mode & SPI_CS_HIGH) ?
- GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH,
- dev_name(&spi->dev));
- if (ret)
- dev_err(&spi->dev, "can't request chipselect gpio %d\n",
- spi->cs_gpio);
- else
- cdns_spi_data->gpio_requested = true;
- } else {
- if (gpio_is_valid(spi->cs_gpio)) {
- int mode = ((spi->mode & SPI_CS_HIGH) ?
- GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH);
-
- ret = gpio_direction_output(spi->cs_gpio, mode);
- if (ret)
- dev_err(&spi->dev, "chipselect gpio %d setup failed (%d)\n",
- spi->cs_gpio, ret);
- }
- }
-
- return ret;
-}
-
-static void cdns_spi_cleanup(struct spi_device *spi)
-{
- struct cdns_spi_device_data *cdns_spi_data = spi_get_ctldata(spi);
-
- if (cdns_spi_data) {
- if (cdns_spi_data->gpio_requested)
- gpio_free(spi->cs_gpio);
- kfree(cdns_spi_data);
- spi_set_ctldata(spi, NULL);
- }
-
-}
-
/**
* cdns_spi_probe - Probe method for the SPI driver
* @pdev: Pointer to the platform_device structure
@@ -584,11 +522,6 @@
goto clk_dis_apb;
}
- pm_runtime_use_autosuspend(&pdev->dev);
- pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
- pm_runtime_set_active(&pdev->dev);
- pm_runtime_enable(&pdev->dev);
-
ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
if (ret < 0)
master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS;
@@ -603,8 +536,10 @@
/* SPI controller initializations */
cdns_spi_init_hw(xspi);
- pm_runtime_mark_last_busy(&pdev->dev);
- pm_runtime_put_autosuspend(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
irq = platform_get_irq(pdev, 0);
if (irq <= 0) {
@@ -621,13 +556,12 @@
goto clk_dis_all;
}
+ master->use_gpio_descriptors = true;
master->prepare_transfer_hardware = cdns_prepare_transfer_hardware;
master->prepare_message = cdns_prepare_message;
master->transfer_one = cdns_transfer_one;
master->unprepare_transfer_hardware = cdns_unprepare_transfer_hardware;
master->set_cs = cdns_spi_chipselect;
- master->setup = cdns_spi_setup;
- master->cleanup = cdns_spi_cleanup;
master->auto_runtime_pm = true;
master->mode_bits = SPI_CPOL | SPI_CPHA;
diff --git a/drivers/spi/spi-clps711x.c b/drivers/spi/spi-clps711x.c
index 18193df..8c03c40 100644
--- a/drivers/spi/spi-clps711x.c
+++ b/drivers/spi/spi-clps711x.c
@@ -11,7 +11,7 @@
#include <linux/io.h>
#include <linux/clk.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
@@ -36,25 +36,6 @@
int len;
};
-static int spi_clps711x_setup(struct spi_device *spi)
-{
- if (!spi->controller_state) {
- int ret;
-
- ret = devm_gpio_request(&spi->master->dev, spi->cs_gpio,
- dev_name(&spi->master->dev));
- if (ret)
- return ret;
-
- spi->controller_state = spi;
- }
-
- /* We are expect that SPI-device is not selected */
- gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
-
- return 0;
-}
-
static int spi_clps711x_prepare_message(struct spi_master *master,
struct spi_message *msg)
{
@@ -125,11 +106,11 @@
if (!master)
return -ENOMEM;
+ master->use_gpio_descriptors = true;
master->bus_num = -1;
master->mode_bits = SPI_CPHA | SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 8);
master->dev.of_node = pdev->dev.of_node;
- master->setup = spi_clps711x_setup;
master->prepare_message = spi_clps711x_prepare_message;
master->transfer_one = spi_clps711x_transfer_one;
diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c
index 56adec8..eb246eb 100644
--- a/drivers/spi/spi-davinci.c
+++ b/drivers/spi/spi-davinci.c
@@ -15,7 +15,7 @@
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
@@ -25,7 +25,6 @@
#include <linux/dma-mapping.h>
#include <linux/of.h>
#include <linux/of_device.h>
-#include <linux/of_gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/slab.h>
@@ -222,12 +221,17 @@
* Board specific chip select logic decides the polarity and cs
* line for the controller
*/
- if (spi->cs_gpio >= 0) {
+ if (spi->cs_gpiod) {
+ /*
+ * FIXME: is this code ever executed? This host does not
+ * set SPI_MASTER_GPIO_SS so this chipselect callback should
+ * not get called from the SPI core when we are using
+ * GPIOs for chip select.
+ */
if (value == BITBANG_CS_ACTIVE)
- gpio_set_value(spi->cs_gpio, spi->mode & SPI_CS_HIGH);
+ gpiod_set_value(spi->cs_gpiod, 1);
else
- gpio_set_value(spi->cs_gpio,
- !(spi->mode & SPI_CS_HIGH));
+ gpiod_set_value(spi->cs_gpiod, 0);
} else {
if (value == BITBANG_CS_ACTIVE) {
if (!(spi->mode & SPI_CS_WORD))
@@ -418,30 +422,18 @@
*/
static int davinci_spi_setup(struct spi_device *spi)
{
- int retval = 0;
struct davinci_spi *dspi;
- struct spi_master *master = spi->master;
struct device_node *np = spi->dev.of_node;
bool internal_cs = true;
dspi = spi_master_get_devdata(spi->master);
if (!(spi->mode & SPI_NO_CS)) {
- if (np && (master->cs_gpios != NULL) && (spi->cs_gpio >= 0)) {
- retval = gpio_direction_output(
- spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
+ if (np && spi->cs_gpiod)
internal_cs = false;
- }
- if (retval) {
- dev_err(&spi->dev, "GPIO %d setup failed (%d)\n",
- spi->cs_gpio, retval);
- return retval;
- }
-
- if (internal_cs) {
+ if (internal_cs)
set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
- }
}
if (spi->mode & SPI_READY)
@@ -962,6 +954,7 @@
if (ret)
goto free_master;
+ master->use_gpio_descriptors = true;
master->dev.of_node = pdev->dev.of_node;
master->bus_num = pdev->id;
master->num_chipselect = pdata->num_chipselect;
@@ -980,27 +973,6 @@
if (dspi->version == SPI_VERSION_2)
dspi->bitbang.flags |= SPI_READY;
- if (pdev->dev.of_node) {
- int i;
-
- for (i = 0; i < pdata->num_chipselect; i++) {
- int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
- "cs-gpios", i);
-
- if (cs_gpio == -EPROBE_DEFER) {
- ret = cs_gpio;
- goto free_clk;
- }
-
- if (gpio_is_valid(cs_gpio)) {
- ret = devm_gpio_request(&pdev->dev, cs_gpio,
- dev_name(&pdev->dev));
- if (ret)
- goto free_clk;
- }
- }
- }
-
dspi->bitbang.txrx_bufs = davinci_spi_bufs;
ret = davinci_spi_request_dma(dspi);
diff --git a/drivers/spi/spi-dw-mmio.c b/drivers/spi/spi-dw-mmio.c
index d0dd781..4bd59a9 100644
--- a/drivers/spi/spi-dw-mmio.c
+++ b/drivers/spi/spi-dw-mmio.c
@@ -18,7 +18,6 @@
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <linux/of_platform.h>
#include <linux/acpi.h>
#include <linux/property.h>
@@ -185,27 +184,6 @@
dws->num_cs = num_cs;
- if (pdev->dev.of_node) {
- int i;
-
- for (i = 0; i < dws->num_cs; i++) {
- int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
- "cs-gpios", i);
-
- if (cs_gpio == -EPROBE_DEFER) {
- ret = cs_gpio;
- goto out;
- }
-
- if (gpio_is_valid(cs_gpio)) {
- ret = devm_gpio_request(&pdev->dev, cs_gpio,
- dev_name(&pdev->dev));
- if (ret)
- goto out;
- }
- }
- }
-
init_func = device_get_match_data(&pdev->dev);
if (init_func) {
ret = init_func(pdev, dwsmmio);
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 2e822a5..ac81025 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -20,7 +20,6 @@
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/spi/spi.h>
-#include <linux/gpio.h>
#include "spi-dw.h"
@@ -54,41 +53,41 @@
if (!buf)
return 0;
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"%s registers:\n", dev_name(&dws->master->dev));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"=================================\n");
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"CTRL0: \t\t0x%08x\n", dw_readl(dws, DW_SPI_CTRL0));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"CTRL1: \t\t0x%08x\n", dw_readl(dws, DW_SPI_CTRL1));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"SSIENR: \t0x%08x\n", dw_readl(dws, DW_SPI_SSIENR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"SER: \t\t0x%08x\n", dw_readl(dws, DW_SPI_SER));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"BAUDR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_BAUDR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"TXFTLR: \t0x%08x\n", dw_readl(dws, DW_SPI_TXFLTR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"RXFTLR: \t0x%08x\n", dw_readl(dws, DW_SPI_RXFLTR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"TXFLR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_TXFLR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"RXFLR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_RXFLR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"SR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_SR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"IMR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_IMR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"ISR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_ISR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"DMACR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_DMACR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"DMATDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMATDLR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"DMARDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMARDLR));
- len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
"=================================\n");
ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
@@ -138,11 +137,10 @@
struct dw_spi *dws = spi_controller_get_devdata(spi->controller);
struct chip_data *chip = spi_get_ctldata(spi);
- /* Chip select logic is inverted from spi_set_cs() */
if (chip && chip->cs_control)
- chip->cs_control(!enable);
+ chip->cs_control(enable);
- if (!enable)
+ if (enable)
dw_writel(dws, DW_SPI_SER, BIT(spi->chip_select));
else if (dws->cs_override)
dw_writel(dws, DW_SPI_SER, 0);
@@ -317,7 +315,8 @@
/* Default SPI mode is SCPOL = 0, SCPH = 0 */
cr0 = (transfer->bits_per_word - 1)
| (chip->type << SPI_FRF_OFFSET)
- | (spi->mode << SPI_MODE_OFFSET)
+ | ((((spi->mode & SPI_CPOL) ? 1 : 0) << SPI_SCOL_OFFSET) |
+ (((spi->mode & SPI_CPHA) ? 1 : 0) << SPI_SCPH_OFFSET))
| (chip->tmode << SPI_TMOD_OFFSET);
/*
@@ -397,7 +396,6 @@
{
struct dw_spi_chip *chip_info = NULL;
struct chip_data *chip;
- int ret;
/* Only alloc on first setup */
chip = spi_get_ctldata(spi);
@@ -425,13 +423,6 @@
chip->tmode = SPI_TMOD_TR;
- if (gpio_is_valid(spi->cs_gpio)) {
- ret = gpio_direction_output(spi->cs_gpio,
- !(spi->mode & SPI_CS_HIGH));
- if (ret)
- return ret;
- }
-
return 0;
}
@@ -496,6 +487,7 @@
goto err_free_master;
}
+ master->use_gpio_descriptors = true;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
master->bus_num = dws->bus_num;
diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c
index 5e10dc5..53335cc 100644
--- a/drivers/spi/spi-fsl-dspi.c
+++ b/drivers/spi/spi-fsl-dspi.c
@@ -67,7 +67,7 @@
#define SPI_SR 0x2c
#define SPI_SR_EOQF 0x10000000
#define SPI_SR_TCFQF 0x80000000
-#define SPI_SR_CLEAR 0xdaad0000
+#define SPI_SR_CLEAR 0x9aaf0000
#define SPI_RSER_TFFFE BIT(25)
#define SPI_RSER_TFFFD BIT(24)
@@ -233,6 +233,9 @@
{
u16 cmd = dspi->tx_cmd, data = dspi_pop_tx(dspi);
+ if (spi_controller_is_slave(dspi->master))
+ return data;
+
if (dspi->len > 0)
cmd |= SPI_PUSHR_CMD_CONT;
return cmd << 16 | data;
@@ -329,6 +332,11 @@
dma_async_issue_pending(dma->chan_rx);
dma_async_issue_pending(dma->chan_tx);
+ if (spi_controller_is_slave(dspi->master)) {
+ wait_for_completion_interruptible(&dspi->dma->cmd_rx_complete);
+ return 0;
+ }
+
time_left = wait_for_completion_timeout(&dspi->dma->cmd_tx_complete,
DMA_COMPLETION_TIMEOUT);
if (time_left == 0) {
@@ -798,14 +806,18 @@
ns_delay_scale(&pasc, &asc, sck_cs_delay, clkrate);
chip->ctar_val = SPI_CTAR_CPOL(spi->mode & SPI_CPOL ? 1 : 0)
- | SPI_CTAR_CPHA(spi->mode & SPI_CPHA ? 1 : 0)
- | SPI_CTAR_LSBFE(spi->mode & SPI_LSB_FIRST ? 1 : 0)
- | SPI_CTAR_PCSSCK(pcssck)
- | SPI_CTAR_CSSCK(cssck)
- | SPI_CTAR_PASC(pasc)
- | SPI_CTAR_ASC(asc)
- | SPI_CTAR_PBR(pbr)
- | SPI_CTAR_BR(br);
+ | SPI_CTAR_CPHA(spi->mode & SPI_CPHA ? 1 : 0);
+
+ if (!spi_controller_is_slave(dspi->master)) {
+ chip->ctar_val |= SPI_CTAR_LSBFE(spi->mode &
+ SPI_LSB_FIRST ? 1 : 0)
+ | SPI_CTAR_PCSSCK(pcssck)
+ | SPI_CTAR_CSSCK(cssck)
+ | SPI_CTAR_PASC(pasc)
+ | SPI_CTAR_ASC(asc)
+ | SPI_CTAR_PBR(pbr)
+ | SPI_CTAR_BR(br);
+ }
spi_set_ctldata(spi, chip);
@@ -970,8 +982,13 @@
static void dspi_init(struct fsl_dspi *dspi)
{
- regmap_write(dspi->regmap, SPI_MCR, SPI_MCR_MASTER | SPI_MCR_PCSIS |
- (dspi->devtype_data->xspi_mode ? SPI_MCR_XSPI : 0));
+ unsigned int mcr = SPI_MCR_PCSIS |
+ (dspi->devtype_data->xspi_mode ? SPI_MCR_XSPI : 0);
+
+ if (!spi_controller_is_slave(dspi->master))
+ mcr |= SPI_MCR_MASTER;
+
+ regmap_write(dspi->regmap, SPI_MCR, mcr);
regmap_write(dspi->regmap, SPI_SR, SPI_SR_CLEAR);
if (dspi->devtype_data->xspi_mode)
regmap_write(dspi->regmap, SPI_CTARE(0),
@@ -1027,6 +1044,9 @@
}
master->bus_num = bus_num;
+ if (of_property_read_bool(np, "spi-slave"))
+ master->slave = true;
+
dspi->devtype_data = of_device_get_match_data(&pdev->dev);
if (!dspi->devtype_data) {
dev_err(&pdev->dev, "can't get devtype_data\n");
diff --git a/drivers/spi/spi-fsl-lpspi.c b/drivers/spi/spi-fsl-lpspi.c
index 08dcc3c..3918639 100644
--- a/drivers/spi/spi-fsl-lpspi.c
+++ b/drivers/spi/spi-fsl-lpspi.c
@@ -48,10 +48,13 @@
#define CR_RTF BIT(8)
#define CR_RST BIT(1)
#define CR_MEN BIT(0)
+#define SR_MBF BIT(24)
#define SR_TCF BIT(10)
+#define SR_FCF BIT(9)
#define SR_RDF BIT(1)
#define SR_TDF BIT(0)
#define IER_TCIE BIT(10)
+#define IER_FCIE BIT(9)
#define IER_RDIE BIT(1)
#define IER_TDIE BIT(0)
#define CFGR1_PCSCFG BIT(27)
@@ -59,6 +62,7 @@
#define CFGR1_PCSPOL BIT(8)
#define CFGR1_NOSTALL BIT(3)
#define CFGR1_MASTER BIT(0)
+#define FSR_RXCOUNT (BIT(16)|BIT(17)|BIT(18))
#define RSR_RXEMPTY BIT(1)
#define TCR_CPOL BIT(31)
#define TCR_CPHA BIT(30)
@@ -161,28 +165,10 @@
return 0;
}
-static int fsl_lpspi_txfifo_empty(struct fsl_lpspi_data *fsl_lpspi)
-{
- u32 txcnt;
- unsigned long orig_jiffies = jiffies;
-
- do {
- txcnt = readl(fsl_lpspi->base + IMX7ULP_FSR) & 0xff;
-
- if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) {
- dev_dbg(fsl_lpspi->dev, "txfifo empty timeout\n");
- return -ETIMEDOUT;
- }
- cond_resched();
-
- } while (txcnt);
-
- return 0;
-}
-
static void fsl_lpspi_write_tx_fifo(struct fsl_lpspi_data *fsl_lpspi)
{
u8 txfifo_cnt;
+ u32 temp;
txfifo_cnt = readl(fsl_lpspi->base + IMX7ULP_FSR) & 0xff;
@@ -193,9 +179,15 @@
txfifo_cnt++;
}
- if (!fsl_lpspi->remain && (txfifo_cnt < fsl_lpspi->txfifosize))
- writel(0, fsl_lpspi->base + IMX7ULP_TDR);
- else
+ if (txfifo_cnt < fsl_lpspi->txfifosize) {
+ if (!fsl_lpspi->is_slave) {
+ temp = readl(fsl_lpspi->base + IMX7ULP_TCR);
+ temp &= ~TCR_CONTC;
+ writel(temp, fsl_lpspi->base + IMX7ULP_TCR);
+ }
+
+ fsl_lpspi_intctrl(fsl_lpspi, IER_FCIE);
+ } else
fsl_lpspi_intctrl(fsl_lpspi, IER_TDIE);
}
@@ -276,10 +268,6 @@
u32 temp;
int ret;
- temp = CR_RST;
- writel(temp, fsl_lpspi->base + IMX7ULP_CR);
- writel(0, fsl_lpspi->base + IMX7ULP_CR);
-
if (!fsl_lpspi->is_slave) {
ret = fsl_lpspi_set_bitrate(fsl_lpspi);
if (ret)
@@ -370,6 +358,24 @@
return 0;
}
+static int fsl_lpspi_reset(struct fsl_lpspi_data *fsl_lpspi)
+{
+ u32 temp;
+
+ /* Disable all interrupt */
+ fsl_lpspi_intctrl(fsl_lpspi, 0);
+
+ /* W1C for all flags in SR */
+ temp = 0x3F << 8;
+ writel(temp, fsl_lpspi->base + IMX7ULP_SR);
+
+ /* Clear FIFO and disable module */
+ temp = CR_RRF | CR_RTF;
+ writel(temp, fsl_lpspi->base + IMX7ULP_CR);
+
+ return 0;
+}
+
static int fsl_lpspi_transfer_one(struct spi_controller *controller,
struct spi_device *spi,
struct spi_transfer *t)
@@ -391,11 +397,7 @@
if (ret)
return ret;
- ret = fsl_lpspi_txfifo_empty(fsl_lpspi);
- if (ret)
- return ret;
-
- fsl_lpspi_read_rx_fifo(fsl_lpspi);
+ fsl_lpspi_reset(fsl_lpspi);
return 0;
}
@@ -408,7 +410,6 @@
struct spi_device *spi = msg->spi;
struct spi_transfer *xfer;
bool is_first_xfer = true;
- u32 temp;
int ret = 0;
msg->status = 0;
@@ -428,13 +429,6 @@
}
complete:
- if (!fsl_lpspi->is_slave) {
- /* de-assert SS, then finalize current message */
- temp = readl(fsl_lpspi->base + IMX7ULP_TCR);
- temp &= ~TCR_CONTC;
- writel(temp, fsl_lpspi->base + IMX7ULP_TCR);
- }
-
msg->status = ret;
spi_finalize_current_message(controller);
@@ -443,20 +437,30 @@
static irqreturn_t fsl_lpspi_isr(int irq, void *dev_id)
{
+ u32 temp_SR, temp_IER;
struct fsl_lpspi_data *fsl_lpspi = dev_id;
- u32 temp;
+ temp_IER = readl(fsl_lpspi->base + IMX7ULP_IER);
fsl_lpspi_intctrl(fsl_lpspi, 0);
- temp = readl(fsl_lpspi->base + IMX7ULP_SR);
+ temp_SR = readl(fsl_lpspi->base + IMX7ULP_SR);
fsl_lpspi_read_rx_fifo(fsl_lpspi);
- if (temp & SR_TDF) {
+ if ((temp_SR & SR_TDF) && (temp_IER & IER_TDIE)) {
fsl_lpspi_write_tx_fifo(fsl_lpspi);
+ return IRQ_HANDLED;
+ }
- if (!fsl_lpspi->remain)
+ if (temp_SR & SR_MBF ||
+ readl(fsl_lpspi->base + IMX7ULP_FSR) & FSR_RXCOUNT) {
+ writel(SR_FCF, fsl_lpspi->base + IMX7ULP_SR);
+ fsl_lpspi_intctrl(fsl_lpspi, IER_FCIE);
+ return IRQ_HANDLED;
+ }
+
+ if (temp_SR & SR_FCF && (temp_IER & IER_FCIE)) {
+ writel(SR_FCF, fsl_lpspi->base + IMX7ULP_SR);
complete(&fsl_lpspi->xfer_done);
-
return IRQ_HANDLED;
}
diff --git a/drivers/spi/spi-fsl-qspi.c b/drivers/spi/spi-fsl-qspi.c
new file mode 100644
index 0000000..6a713f7
--- /dev/null
+++ b/drivers/spi/spi-fsl-qspi.c
@@ -0,0 +1,966 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/*
+ * Freescale QuadSPI driver.
+ *
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ * Copyright (C) 2018 Bootlin
+ * Copyright (C) 2018 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ *
+ * Transition to SPI MEM interface:
+ * Authors:
+ * Boris Brezillon <bbrezillon@kernel.org>
+ * Frieder Schrempf <frieder.schrempf@kontron.de>
+ * Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
+ * Suresh Gupta <suresh.gupta@nxp.com>
+ *
+ * Based on the original fsl-quadspi.c spi-nor driver:
+ * Author: Freescale Semiconductor, Inc.
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_qos.h>
+#include <linux/sizes.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+/*
+ * The driver only uses one single LUT entry, that is updated on
+ * each call of exec_op(). Index 0 is preset at boot with a basic
+ * read operation, so let's use the last entry (15).
+ */
+#define SEQID_LUT 15
+
+/* Registers used by the driver */
+#define QUADSPI_MCR 0x00
+#define QUADSPI_MCR_RESERVED_MASK GENMASK(19, 16)
+#define QUADSPI_MCR_MDIS_MASK BIT(14)
+#define QUADSPI_MCR_CLR_TXF_MASK BIT(11)
+#define QUADSPI_MCR_CLR_RXF_MASK BIT(10)
+#define QUADSPI_MCR_DDR_EN_MASK BIT(7)
+#define QUADSPI_MCR_END_CFG_MASK GENMASK(3, 2)
+#define QUADSPI_MCR_SWRSTHD_MASK BIT(1)
+#define QUADSPI_MCR_SWRSTSD_MASK BIT(0)
+
+#define QUADSPI_IPCR 0x08
+#define QUADSPI_IPCR_SEQID(x) ((x) << 24)
+
+#define QUADSPI_BUF3CR 0x1c
+#define QUADSPI_BUF3CR_ALLMST_MASK BIT(31)
+#define QUADSPI_BUF3CR_ADATSZ(x) ((x) << 8)
+#define QUADSPI_BUF3CR_ADATSZ_MASK GENMASK(15, 8)
+
+#define QUADSPI_BFGENCR 0x20
+#define QUADSPI_BFGENCR_SEQID(x) ((x) << 12)
+
+#define QUADSPI_BUF0IND 0x30
+#define QUADSPI_BUF1IND 0x34
+#define QUADSPI_BUF2IND 0x38
+#define QUADSPI_SFAR 0x100
+
+#define QUADSPI_SMPR 0x108
+#define QUADSPI_SMPR_DDRSMP_MASK GENMASK(18, 16)
+#define QUADSPI_SMPR_FSDLY_MASK BIT(6)
+#define QUADSPI_SMPR_FSPHS_MASK BIT(5)
+#define QUADSPI_SMPR_HSENA_MASK BIT(0)
+
+#define QUADSPI_RBCT 0x110
+#define QUADSPI_RBCT_WMRK_MASK GENMASK(4, 0)
+#define QUADSPI_RBCT_RXBRD_USEIPS BIT(8)
+
+#define QUADSPI_TBDR 0x154
+
+#define QUADSPI_SR 0x15c
+#define QUADSPI_SR_IP_ACC_MASK BIT(1)
+#define QUADSPI_SR_AHB_ACC_MASK BIT(2)
+
+#define QUADSPI_FR 0x160
+#define QUADSPI_FR_TFF_MASK BIT(0)
+
+#define QUADSPI_SPTRCLR 0x16c
+#define QUADSPI_SPTRCLR_IPPTRC BIT(8)
+#define QUADSPI_SPTRCLR_BFPTRC BIT(0)
+
+#define QUADSPI_SFA1AD 0x180
+#define QUADSPI_SFA2AD 0x184
+#define QUADSPI_SFB1AD 0x188
+#define QUADSPI_SFB2AD 0x18c
+#define QUADSPI_RBDR(x) (0x200 + ((x) * 4))
+
+#define QUADSPI_LUTKEY 0x300
+#define QUADSPI_LUTKEY_VALUE 0x5AF05AF0
+
+#define QUADSPI_LCKCR 0x304
+#define QUADSPI_LCKER_LOCK BIT(0)
+#define QUADSPI_LCKER_UNLOCK BIT(1)
+
+#define QUADSPI_RSER 0x164
+#define QUADSPI_RSER_TFIE BIT(0)
+
+#define QUADSPI_LUT_BASE 0x310
+#define QUADSPI_LUT_OFFSET (SEQID_LUT * 4 * 4)
+#define QUADSPI_LUT_REG(idx) \
+ (QUADSPI_LUT_BASE + QUADSPI_LUT_OFFSET + (idx) * 4)
+
+/* Instruction set for the LUT register */
+#define LUT_STOP 0
+#define LUT_CMD 1
+#define LUT_ADDR 2
+#define LUT_DUMMY 3
+#define LUT_MODE 4
+#define LUT_MODE2 5
+#define LUT_MODE4 6
+#define LUT_FSL_READ 7
+#define LUT_FSL_WRITE 8
+#define LUT_JMP_ON_CS 9
+#define LUT_ADDR_DDR 10
+#define LUT_MODE_DDR 11
+#define LUT_MODE2_DDR 12
+#define LUT_MODE4_DDR 13
+#define LUT_FSL_READ_DDR 14
+#define LUT_FSL_WRITE_DDR 15
+#define LUT_DATA_LEARN 16
+
+/*
+ * The PAD definitions for LUT register.
+ *
+ * The pad stands for the number of IO lines [0:3].
+ * For example, the quad read needs four IO lines,
+ * so you should use LUT_PAD(4).
+ */
+#define LUT_PAD(x) (fls(x) - 1)
+
+/*
+ * Macro for constructing the LUT entries with the following
+ * register layout:
+ *
+ * ---------------------------------------------------
+ * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
+ * ---------------------------------------------------
+ */
+#define LUT_DEF(idx, ins, pad, opr) \
+ ((((ins) << 10) | ((pad) << 8) | (opr)) << (((idx) % 2) * 16))
+
+/* Controller needs driver to swap endianness */
+#define QUADSPI_QUIRK_SWAP_ENDIAN BIT(0)
+
+/* Controller needs 4x internal clock */
+#define QUADSPI_QUIRK_4X_INT_CLK BIT(1)
+
+/*
+ * TKT253890, the controller needs the driver to fill the txfifo with
+ * 16 bytes at least to trigger a data transfer, even though the extra
+ * data won't be transferred.
+ */
+#define QUADSPI_QUIRK_TKT253890 BIT(2)
+
+/* TKT245618, the controller cannot wake up from wait mode */
+#define QUADSPI_QUIRK_TKT245618 BIT(3)
+
+/*
+ * Controller adds QSPI_AMBA_BASE (base address of the mapped memory)
+ * internally. No need to add it when setting SFXXAD and SFAR registers
+ */
+#define QUADSPI_QUIRK_BASE_INTERNAL BIT(4)
+
+struct fsl_qspi_devtype_data {
+ unsigned int rxfifo;
+ unsigned int txfifo;
+ unsigned int ahb_buf_size;
+ unsigned int quirks;
+ bool little_endian;
+};
+
+static const struct fsl_qspi_devtype_data vybrid_data = {
+ .rxfifo = SZ_128,
+ .txfifo = SZ_64,
+ .ahb_buf_size = SZ_1K,
+ .quirks = QUADSPI_QUIRK_SWAP_ENDIAN,
+ .little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data imx6sx_data = {
+ .rxfifo = SZ_128,
+ .txfifo = SZ_512,
+ .ahb_buf_size = SZ_1K,
+ .quirks = QUADSPI_QUIRK_4X_INT_CLK | QUADSPI_QUIRK_TKT245618,
+ .little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data imx7d_data = {
+ .rxfifo = SZ_512,
+ .txfifo = SZ_512,
+ .ahb_buf_size = SZ_1K,
+ .quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_4X_INT_CLK,
+ .little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data imx6ul_data = {
+ .rxfifo = SZ_128,
+ .txfifo = SZ_512,
+ .ahb_buf_size = SZ_1K,
+ .quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_4X_INT_CLK,
+ .little_endian = true,
+};
+
+static const struct fsl_qspi_devtype_data ls1021a_data = {
+ .rxfifo = SZ_128,
+ .txfifo = SZ_64,
+ .ahb_buf_size = SZ_1K,
+ .quirks = 0,
+ .little_endian = false,
+};
+
+static const struct fsl_qspi_devtype_data ls2080a_data = {
+ .rxfifo = SZ_128,
+ .txfifo = SZ_64,
+ .ahb_buf_size = SZ_1K,
+ .quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_BASE_INTERNAL,
+ .little_endian = true,
+};
+
+struct fsl_qspi {
+ void __iomem *iobase;
+ void __iomem *ahb_addr;
+ u32 memmap_phy;
+ struct clk *clk, *clk_en;
+ struct device *dev;
+ struct completion c;
+ const struct fsl_qspi_devtype_data *devtype_data;
+ struct mutex lock;
+ struct pm_qos_request pm_qos_req;
+ int selected;
+};
+
+static inline int needs_swap_endian(struct fsl_qspi *q)
+{
+ return q->devtype_data->quirks & QUADSPI_QUIRK_SWAP_ENDIAN;
+}
+
+static inline int needs_4x_clock(struct fsl_qspi *q)
+{
+ return q->devtype_data->quirks & QUADSPI_QUIRK_4X_INT_CLK;
+}
+
+static inline int needs_fill_txfifo(struct fsl_qspi *q)
+{
+ return q->devtype_data->quirks & QUADSPI_QUIRK_TKT253890;
+}
+
+static inline int needs_wakeup_wait_mode(struct fsl_qspi *q)
+{
+ return q->devtype_data->quirks & QUADSPI_QUIRK_TKT245618;
+}
+
+static inline int needs_amba_base_offset(struct fsl_qspi *q)
+{
+ return !(q->devtype_data->quirks & QUADSPI_QUIRK_BASE_INTERNAL);
+}
+
+/*
+ * An IC bug makes it necessary to rearrange the 32-bit data.
+ * Later chips, such as IMX6SLX, have fixed this bug.
+ */
+static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a)
+{
+ return needs_swap_endian(q) ? __swab32(a) : a;
+}
+
+/*
+ * R/W functions for big- or little-endian registers:
+ * The QSPI controller's endianness is independent of
+ * the CPU core's endianness. So far, although the CPU
+ * core is little-endian the QSPI controller can use
+ * big-endian or little-endian.
+ */
+static void qspi_writel(struct fsl_qspi *q, u32 val, void __iomem *addr)
+{
+ if (q->devtype_data->little_endian)
+ iowrite32(val, addr);
+ else
+ iowrite32be(val, addr);
+}
+
+static u32 qspi_readl(struct fsl_qspi *q, void __iomem *addr)
+{
+ if (q->devtype_data->little_endian)
+ return ioread32(addr);
+
+ return ioread32be(addr);
+}
+
+static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id)
+{
+ struct fsl_qspi *q = dev_id;
+ u32 reg;
+
+ /* clear interrupt */
+ reg = qspi_readl(q, q->iobase + QUADSPI_FR);
+ qspi_writel(q, reg, q->iobase + QUADSPI_FR);
+
+ if (reg & QUADSPI_FR_TFF_MASK)
+ complete(&q->c);
+
+ dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", 0, reg);
+ return IRQ_HANDLED;
+}
+
+static int fsl_qspi_check_buswidth(struct fsl_qspi *q, u8 width)
+{
+ switch (width) {
+ case 1:
+ case 2:
+ case 4:
+ return 0;
+ }
+
+ return -ENOTSUPP;
+}
+
+static bool fsl_qspi_supports_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+ int ret;
+
+ ret = fsl_qspi_check_buswidth(q, op->cmd.buswidth);
+
+ if (op->addr.nbytes)
+ ret |= fsl_qspi_check_buswidth(q, op->addr.buswidth);
+
+ if (op->dummy.nbytes)
+ ret |= fsl_qspi_check_buswidth(q, op->dummy.buswidth);
+
+ if (op->data.nbytes)
+ ret |= fsl_qspi_check_buswidth(q, op->data.buswidth);
+
+ if (ret)
+ return false;
+
+ /*
+ * The number of instructions needed for the op, needs
+ * to fit into a single LUT entry.
+ */
+ if (op->addr.nbytes +
+ (op->dummy.nbytes ? 1:0) +
+ (op->data.nbytes ? 1:0) > 6)
+ return false;
+
+ /* Max 64 dummy clock cycles supported */
+ if (op->dummy.nbytes &&
+ (op->dummy.nbytes * 8 / op->dummy.buswidth > 64))
+ return false;
+
+ /* Max data length, check controller limits and alignment */
+ if (op->data.dir == SPI_MEM_DATA_IN &&
+ (op->data.nbytes > q->devtype_data->ahb_buf_size ||
+ (op->data.nbytes > q->devtype_data->rxfifo - 4 &&
+ !IS_ALIGNED(op->data.nbytes, 8))))
+ return false;
+
+ if (op->data.dir == SPI_MEM_DATA_OUT &&
+ op->data.nbytes > q->devtype_data->txfifo)
+ return false;
+
+ return true;
+}
+
+static void fsl_qspi_prepare_lut(struct fsl_qspi *q,
+ const struct spi_mem_op *op)
+{
+ void __iomem *base = q->iobase;
+ u32 lutval[4] = {};
+ int lutidx = 1, i;
+
+ lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth),
+ op->cmd.opcode);
+
+ /*
+ * For some unknown reason, using LUT_ADDR doesn't work in some
+ * cases (at least with only one byte long addresses), so
+ * let's use LUT_MODE to write the address bytes one by one
+ */
+ for (i = 0; i < op->addr.nbytes; i++) {
+ u8 addrbyte = op->addr.val >> (8 * (op->addr.nbytes - i - 1));
+
+ lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_MODE,
+ LUT_PAD(op->addr.buswidth),
+ addrbyte);
+ lutidx++;
+ }
+
+ if (op->dummy.nbytes) {
+ lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY,
+ LUT_PAD(op->dummy.buswidth),
+ op->dummy.nbytes * 8 /
+ op->dummy.buswidth);
+ lutidx++;
+ }
+
+ if (op->data.nbytes) {
+ lutval[lutidx / 2] |= LUT_DEF(lutidx,
+ op->data.dir == SPI_MEM_DATA_IN ?
+ LUT_FSL_READ : LUT_FSL_WRITE,
+ LUT_PAD(op->data.buswidth),
+ 0);
+ lutidx++;
+ }
+
+ lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0);
+
+ /* unlock LUT */
+ qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
+ qspi_writel(q, QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR);
+
+ /* fill LUT */
+ for (i = 0; i < ARRAY_SIZE(lutval); i++)
+ qspi_writel(q, lutval[i], base + QUADSPI_LUT_REG(i));
+
+ /* lock LUT */
+ qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
+ qspi_writel(q, QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR);
+}
+
+static int fsl_qspi_clk_prep_enable(struct fsl_qspi *q)
+{
+ int ret;
+
+ ret = clk_prepare_enable(q->clk_en);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(q->clk);
+ if (ret) {
+ clk_disable_unprepare(q->clk_en);
+ return ret;
+ }
+
+ if (needs_wakeup_wait_mode(q))
+ pm_qos_add_request(&q->pm_qos_req, PM_QOS_CPU_DMA_LATENCY, 0);
+
+ return 0;
+}
+
+static void fsl_qspi_clk_disable_unprep(struct fsl_qspi *q)
+{
+ if (needs_wakeup_wait_mode(q))
+ pm_qos_remove_request(&q->pm_qos_req);
+
+ clk_disable_unprepare(q->clk);
+ clk_disable_unprepare(q->clk_en);
+}
+
+/*
+ * If we have changed the content of the flash by writing or erasing, or if we
+ * read from flash with a different offset into the page buffer, we need to
+ * invalidate the AHB buffer. If we do not do so, we may read out the wrong
+ * data. The spec tells us reset the AHB domain and Serial Flash domain at
+ * the same time.
+ */
+static void fsl_qspi_invalidate(struct fsl_qspi *q)
+{
+ u32 reg;
+
+ reg = qspi_readl(q, q->iobase + QUADSPI_MCR);
+ reg |= QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK;
+ qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
+
+ /*
+ * The minimum delay : 1 AHB + 2 SFCK clocks.
+ * Delay 1 us is enough.
+ */
+ udelay(1);
+
+ reg &= ~(QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK);
+ qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
+}
+
+static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device *spi)
+{
+ unsigned long rate = spi->max_speed_hz;
+ int ret;
+
+ if (q->selected == spi->chip_select)
+ return;
+
+ if (needs_4x_clock(q))
+ rate *= 4;
+
+ fsl_qspi_clk_disable_unprep(q);
+
+ ret = clk_set_rate(q->clk, rate);
+ if (ret)
+ return;
+
+ ret = fsl_qspi_clk_prep_enable(q);
+ if (ret)
+ return;
+
+ q->selected = spi->chip_select;
+
+ fsl_qspi_invalidate(q);
+}
+
+static void fsl_qspi_read_ahb(struct fsl_qspi *q, const struct spi_mem_op *op)
+{
+ memcpy_fromio(op->data.buf.in,
+ q->ahb_addr + q->selected * q->devtype_data->ahb_buf_size,
+ op->data.nbytes);
+}
+
+static void fsl_qspi_fill_txfifo(struct fsl_qspi *q,
+ const struct spi_mem_op *op)
+{
+ void __iomem *base = q->iobase;
+ int i;
+ u32 val;
+
+ for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 4); i += 4) {
+ memcpy(&val, op->data.buf.out + i, 4);
+ val = fsl_qspi_endian_xchg(q, val);
+ qspi_writel(q, val, base + QUADSPI_TBDR);
+ }
+
+ if (i < op->data.nbytes) {
+ memcpy(&val, op->data.buf.out + i, op->data.nbytes - i);
+ val = fsl_qspi_endian_xchg(q, val);
+ qspi_writel(q, val, base + QUADSPI_TBDR);
+ }
+
+ if (needs_fill_txfifo(q)) {
+ for (i = op->data.nbytes; i < 16; i += 4)
+ qspi_writel(q, 0, base + QUADSPI_TBDR);
+ }
+}
+
+static void fsl_qspi_read_rxfifo(struct fsl_qspi *q,
+ const struct spi_mem_op *op)
+{
+ void __iomem *base = q->iobase;
+ int i;
+ u8 *buf = op->data.buf.in;
+ u32 val;
+
+ for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 4); i += 4) {
+ val = qspi_readl(q, base + QUADSPI_RBDR(i / 4));
+ val = fsl_qspi_endian_xchg(q, val);
+ memcpy(buf + i, &val, 4);
+ }
+
+ if (i < op->data.nbytes) {
+ val = qspi_readl(q, base + QUADSPI_RBDR(i / 4));
+ val = fsl_qspi_endian_xchg(q, val);
+ memcpy(buf + i, &val, op->data.nbytes - i);
+ }
+}
+
+static int fsl_qspi_do_op(struct fsl_qspi *q, const struct spi_mem_op *op)
+{
+ void __iomem *base = q->iobase;
+ int err = 0;
+
+ init_completion(&q->c);
+
+ /*
+ * Always start the sequence at the same index since we update
+ * the LUT at each exec_op() call. And also specify the DATA
+ * length, since it's has not been specified in the LUT.
+ */
+ qspi_writel(q, op->data.nbytes | QUADSPI_IPCR_SEQID(SEQID_LUT),
+ base + QUADSPI_IPCR);
+
+ /* Wait for the interrupt. */
+ if (!wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000)))
+ err = -ETIMEDOUT;
+
+ if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN)
+ fsl_qspi_read_rxfifo(q, op);
+
+ return err;
+}
+
+static int fsl_qspi_readl_poll_tout(struct fsl_qspi *q, void __iomem *base,
+ u32 mask, u32 delay_us, u32 timeout_us)
+{
+ u32 reg;
+
+ if (!q->devtype_data->little_endian)
+ mask = (u32)cpu_to_be32(mask);
+
+ return readl_poll_timeout(base, reg, !(reg & mask), delay_us,
+ timeout_us);
+}
+
+static int fsl_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+ void __iomem *base = q->iobase;
+ u32 addr_offset = 0;
+ int err = 0;
+
+ mutex_lock(&q->lock);
+
+ /* wait for the controller being ready */
+ fsl_qspi_readl_poll_tout(q, base + QUADSPI_SR, (QUADSPI_SR_IP_ACC_MASK |
+ QUADSPI_SR_AHB_ACC_MASK), 10, 1000);
+
+ fsl_qspi_select_mem(q, mem->spi);
+
+ if (needs_amba_base_offset(q))
+ addr_offset = q->memmap_phy;
+
+ qspi_writel(q,
+ q->selected * q->devtype_data->ahb_buf_size + addr_offset,
+ base + QUADSPI_SFAR);
+
+ qspi_writel(q, qspi_readl(q, base + QUADSPI_MCR) |
+ QUADSPI_MCR_CLR_RXF_MASK | QUADSPI_MCR_CLR_TXF_MASK,
+ base + QUADSPI_MCR);
+
+ qspi_writel(q, QUADSPI_SPTRCLR_BFPTRC | QUADSPI_SPTRCLR_IPPTRC,
+ base + QUADSPI_SPTRCLR);
+
+ fsl_qspi_prepare_lut(q, op);
+
+ /*
+ * If we have large chunks of data, we read them through the AHB bus
+ * by accessing the mapped memory. In all other cases we use
+ * IP commands to access the flash.
+ */
+ if (op->data.nbytes > (q->devtype_data->rxfifo - 4) &&
+ op->data.dir == SPI_MEM_DATA_IN) {
+ fsl_qspi_read_ahb(q, op);
+ } else {
+ qspi_writel(q, QUADSPI_RBCT_WMRK_MASK |
+ QUADSPI_RBCT_RXBRD_USEIPS, base + QUADSPI_RBCT);
+
+ if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
+ fsl_qspi_fill_txfifo(q, op);
+
+ err = fsl_qspi_do_op(q, op);
+ }
+
+ /* Invalidate the data in the AHB buffer. */
+ fsl_qspi_invalidate(q);
+
+ mutex_unlock(&q->lock);
+
+ return err;
+}
+
+static int fsl_qspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
+{
+ struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+
+ if (op->data.dir == SPI_MEM_DATA_OUT) {
+ if (op->data.nbytes > q->devtype_data->txfifo)
+ op->data.nbytes = q->devtype_data->txfifo;
+ } else {
+ if (op->data.nbytes > q->devtype_data->ahb_buf_size)
+ op->data.nbytes = q->devtype_data->ahb_buf_size;
+ else if (op->data.nbytes > (q->devtype_data->rxfifo - 4))
+ op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8);
+ }
+
+ return 0;
+}
+
+static int fsl_qspi_default_setup(struct fsl_qspi *q)
+{
+ void __iomem *base = q->iobase;
+ u32 reg, addr_offset = 0;
+ int ret;
+
+ /* disable and unprepare clock to avoid glitch pass to controller */
+ fsl_qspi_clk_disable_unprep(q);
+
+ /* the default frequency, we will change it later if necessary. */
+ ret = clk_set_rate(q->clk, 66000000);
+ if (ret)
+ return ret;
+
+ ret = fsl_qspi_clk_prep_enable(q);
+ if (ret)
+ return ret;
+
+ /* Reset the module */
+ qspi_writel(q, QUADSPI_MCR_SWRSTSD_MASK | QUADSPI_MCR_SWRSTHD_MASK,
+ base + QUADSPI_MCR);
+ udelay(1);
+
+ /* Disable the module */
+ qspi_writel(q, QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK,
+ base + QUADSPI_MCR);
+
+ reg = qspi_readl(q, base + QUADSPI_SMPR);
+ qspi_writel(q, reg & ~(QUADSPI_SMPR_FSDLY_MASK
+ | QUADSPI_SMPR_FSPHS_MASK
+ | QUADSPI_SMPR_HSENA_MASK
+ | QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR);
+
+ /* We only use the buffer3 for AHB read */
+ qspi_writel(q, 0, base + QUADSPI_BUF0IND);
+ qspi_writel(q, 0, base + QUADSPI_BUF1IND);
+ qspi_writel(q, 0, base + QUADSPI_BUF2IND);
+
+ qspi_writel(q, QUADSPI_BFGENCR_SEQID(SEQID_LUT),
+ q->iobase + QUADSPI_BFGENCR);
+ qspi_writel(q, QUADSPI_RBCT_WMRK_MASK, base + QUADSPI_RBCT);
+ qspi_writel(q, QUADSPI_BUF3CR_ALLMST_MASK |
+ QUADSPI_BUF3CR_ADATSZ(q->devtype_data->ahb_buf_size / 8),
+ base + QUADSPI_BUF3CR);
+
+ if (needs_amba_base_offset(q))
+ addr_offset = q->memmap_phy;
+
+ /*
+ * In HW there can be a maximum of four chips on two buses with
+ * two chip selects on each bus. We use four chip selects in SW
+ * to differentiate between the four chips.
+ * We use ahb_buf_size for each chip and set SFA1AD, SFA2AD, SFB1AD,
+ * SFB2AD accordingly.
+ */
+ qspi_writel(q, q->devtype_data->ahb_buf_size + addr_offset,
+ base + QUADSPI_SFA1AD);
+ qspi_writel(q, q->devtype_data->ahb_buf_size * 2 + addr_offset,
+ base + QUADSPI_SFA2AD);
+ qspi_writel(q, q->devtype_data->ahb_buf_size * 3 + addr_offset,
+ base + QUADSPI_SFB1AD);
+ qspi_writel(q, q->devtype_data->ahb_buf_size * 4 + addr_offset,
+ base + QUADSPI_SFB2AD);
+
+ q->selected = -1;
+
+ /* Enable the module */
+ qspi_writel(q, QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK,
+ base + QUADSPI_MCR);
+
+ /* clear all interrupt status */
+ qspi_writel(q, 0xffffffff, q->iobase + QUADSPI_FR);
+
+ /* enable the interrupt */
+ qspi_writel(q, QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER);
+
+ return 0;
+}
+
+static const char *fsl_qspi_get_name(struct spi_mem *mem)
+{
+ struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master);
+ struct device *dev = &mem->spi->dev;
+ const char *name;
+
+ /*
+ * In order to keep mtdparts compatible with the old MTD driver at
+ * mtd/spi-nor/fsl-quadspi.c, we set a custom name derived from the
+ * platform_device of the controller.
+ */
+ if (of_get_available_child_count(q->dev->of_node) == 1)
+ return dev_name(q->dev);
+
+ name = devm_kasprintf(dev, GFP_KERNEL,
+ "%s-%d", dev_name(q->dev),
+ mem->spi->chip_select);
+
+ if (!name) {
+ dev_err(dev, "failed to get memory for custom flash name\n");
+ return ERR_PTR(-ENOMEM);
+ }
+
+ return name;
+}
+
+static const struct spi_controller_mem_ops fsl_qspi_mem_ops = {
+ .adjust_op_size = fsl_qspi_adjust_op_size,
+ .supports_op = fsl_qspi_supports_op,
+ .exec_op = fsl_qspi_exec_op,
+ .get_name = fsl_qspi_get_name,
+};
+
+static int fsl_qspi_probe(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct resource *res;
+ struct fsl_qspi *q;
+ int ret;
+
+ ctlr = spi_alloc_master(&pdev->dev, sizeof(*q));
+ if (!ctlr)
+ return -ENOMEM;
+
+ ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD |
+ SPI_TX_DUAL | SPI_TX_QUAD;
+
+ q = spi_controller_get_devdata(ctlr);
+ q->dev = dev;
+ q->devtype_data = of_device_get_match_data(dev);
+ if (!q->devtype_data) {
+ ret = -ENODEV;
+ goto err_put_ctrl;
+ }
+
+ platform_set_drvdata(pdev, q);
+
+ /* find the resources */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI");
+ q->iobase = devm_ioremap_resource(dev, res);
+ if (IS_ERR(q->iobase)) {
+ ret = PTR_ERR(q->iobase);
+ goto err_put_ctrl;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "QuadSPI-memory");
+ q->ahb_addr = devm_ioremap_resource(dev, res);
+ if (IS_ERR(q->ahb_addr)) {
+ ret = PTR_ERR(q->ahb_addr);
+ goto err_put_ctrl;
+ }
+
+ q->memmap_phy = res->start;
+
+ /* find the clocks */
+ q->clk_en = devm_clk_get(dev, "qspi_en");
+ if (IS_ERR(q->clk_en)) {
+ ret = PTR_ERR(q->clk_en);
+ goto err_put_ctrl;
+ }
+
+ q->clk = devm_clk_get(dev, "qspi");
+ if (IS_ERR(q->clk)) {
+ ret = PTR_ERR(q->clk);
+ goto err_put_ctrl;
+ }
+
+ ret = fsl_qspi_clk_prep_enable(q);
+ if (ret) {
+ dev_err(dev, "can not enable the clock\n");
+ goto err_put_ctrl;
+ }
+
+ /* find the irq */
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0) {
+ dev_err(dev, "failed to get the irq: %d\n", ret);
+ goto err_disable_clk;
+ }
+
+ ret = devm_request_irq(dev, ret,
+ fsl_qspi_irq_handler, 0, pdev->name, q);
+ if (ret) {
+ dev_err(dev, "failed to request irq: %d\n", ret);
+ goto err_disable_clk;
+ }
+
+ mutex_init(&q->lock);
+
+ ctlr->bus_num = -1;
+ ctlr->num_chipselect = 4;
+ ctlr->mem_ops = &fsl_qspi_mem_ops;
+
+ fsl_qspi_default_setup(q);
+
+ ctlr->dev.of_node = np;
+
+ ret = spi_register_controller(ctlr);
+ if (ret)
+ goto err_destroy_mutex;
+
+ return 0;
+
+err_destroy_mutex:
+ mutex_destroy(&q->lock);
+
+err_disable_clk:
+ fsl_qspi_clk_disable_unprep(q);
+
+err_put_ctrl:
+ spi_controller_put(ctlr);
+
+ dev_err(dev, "Freescale QuadSPI probe failed\n");
+ return ret;
+}
+
+static int fsl_qspi_remove(struct platform_device *pdev)
+{
+ struct fsl_qspi *q = platform_get_drvdata(pdev);
+
+ /* disable the hardware */
+ qspi_writel(q, QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR);
+ qspi_writel(q, 0x0, q->iobase + QUADSPI_RSER);
+
+ fsl_qspi_clk_disable_unprep(q);
+
+ mutex_destroy(&q->lock);
+
+ return 0;
+}
+
+static int fsl_qspi_suspend(struct device *dev)
+{
+ return 0;
+}
+
+static int fsl_qspi_resume(struct device *dev)
+{
+ struct fsl_qspi *q = dev_get_drvdata(dev);
+
+ fsl_qspi_default_setup(q);
+
+ return 0;
+}
+
+static const struct of_device_id fsl_qspi_dt_ids[] = {
+ { .compatible = "fsl,vf610-qspi", .data = &vybrid_data, },
+ { .compatible = "fsl,imx6sx-qspi", .data = &imx6sx_data, },
+ { .compatible = "fsl,imx7d-qspi", .data = &imx7d_data, },
+ { .compatible = "fsl,imx6ul-qspi", .data = &imx6ul_data, },
+ { .compatible = "fsl,ls1021a-qspi", .data = &ls1021a_data, },
+ { .compatible = "fsl,ls2080a-qspi", .data = &ls2080a_data, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids);
+
+static const struct dev_pm_ops fsl_qspi_pm_ops = {
+ .suspend = fsl_qspi_suspend,
+ .resume = fsl_qspi_resume,
+};
+
+static struct platform_driver fsl_qspi_driver = {
+ .driver = {
+ .name = "fsl-quadspi",
+ .of_match_table = fsl_qspi_dt_ids,
+ .pm = &fsl_qspi_pm_ops,
+ },
+ .probe = fsl_qspi_probe,
+ .remove = fsl_qspi_remove,
+};
+module_platform_driver(fsl_qspi_driver);
+
+MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver");
+MODULE_AUTHOR("Freescale Semiconductor Inc.");
+MODULE_AUTHOR("Boris Brezillon <bbrezillon@kernel.org>");
+MODULE_AUTHOR("Frieder Schrempf <frieder.schrempf@kontron.de>");
+MODULE_AUTHOR("Yogesh Gaur <yogeshnarayan.gaur@nxp.com>");
+MODULE_AUTHOR("Suresh Gupta <suresh.gupta@nxp.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
index fdb7cb88..5f0b0d5 100644
--- a/drivers/spi/spi-geni-qcom.c
+++ b/drivers/spi/spi-geni-qcom.c
@@ -89,9 +89,6 @@
int irq;
};
-static void handle_fifo_timeout(struct spi_master *spi,
- struct spi_message *msg);
-
static int get_spi_clk_cfg(unsigned int speed_hz,
struct spi_geni_master *mas,
unsigned int *clk_idx,
@@ -122,6 +119,32 @@
return ret;
}
+static void handle_fifo_timeout(struct spi_master *spi,
+ struct spi_message *msg)
+{
+ struct spi_geni_master *mas = spi_master_get_devdata(spi);
+ unsigned long time_left, flags;
+ struct geni_se *se = &mas->se;
+
+ spin_lock_irqsave(&mas->lock, flags);
+ reinit_completion(&mas->xfer_done);
+ mas->cur_mcmd = CMD_CANCEL;
+ geni_se_cancel_m_cmd(se);
+ writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
+ spin_unlock_irqrestore(&mas->lock, flags);
+ time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
+ if (time_left)
+ return;
+
+ spin_lock_irqsave(&mas->lock, flags);
+ reinit_completion(&mas->xfer_done);
+ geni_se_abort_m_cmd(se);
+ spin_unlock_irqrestore(&mas->lock, flags);
+ time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
+ if (!time_left)
+ dev_err(mas->dev, "Failed to cancel/abort m_cmd\n");
+}
+
static void spi_geni_set_cs(struct spi_device *slv, bool set_flag)
{
struct spi_geni_master *mas = spi_master_get_devdata(slv->master);
@@ -233,7 +256,6 @@
struct geni_se *se = &mas->se;
geni_se_select_mode(se, GENI_SE_FIFO);
- reinit_completion(&mas->xfer_done);
ret = setup_fifo_params(spi_msg->spi, spi);
if (ret)
dev_err(mas->dev, "Couldn't select mode %d\n", ret);
@@ -357,32 +379,6 @@
writel(mas->tx_wm, se->base + SE_GENI_TX_WATERMARK_REG);
}
-static void handle_fifo_timeout(struct spi_master *spi,
- struct spi_message *msg)
-{
- struct spi_geni_master *mas = spi_master_get_devdata(spi);
- unsigned long time_left, flags;
- struct geni_se *se = &mas->se;
-
- spin_lock_irqsave(&mas->lock, flags);
- reinit_completion(&mas->xfer_done);
- mas->cur_mcmd = CMD_CANCEL;
- geni_se_cancel_m_cmd(se);
- writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
- spin_unlock_irqrestore(&mas->lock, flags);
- time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
- if (time_left)
- return;
-
- spin_lock_irqsave(&mas->lock, flags);
- reinit_completion(&mas->xfer_done);
- geni_se_abort_m_cmd(se);
- spin_unlock_irqrestore(&mas->lock, flags);
- time_left = wait_for_completion_timeout(&mas->xfer_done, HZ);
- if (!time_left)
- dev_err(mas->dev, "Failed to cancel/abort m_cmd\n");
-}
-
static int spi_geni_transfer_one(struct spi_master *spi,
struct spi_device *slv,
struct spi_transfer *xfer)
diff --git a/drivers/spi/spi-gpio.c b/drivers/spi/spi-gpio.c
index a4aee26..53b35c5 100644
--- a/drivers/spi/spi-gpio.c
+++ b/drivers/spi/spi-gpio.c
@@ -428,7 +428,8 @@
return status;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
- master->mode_bits = SPI_3WIRE | SPI_3WIRE_HIZ | SPI_CPHA | SPI_CPOL;
+ master->mode_bits = SPI_3WIRE | SPI_3WIRE_HIZ | SPI_CPHA | SPI_CPOL |
+ SPI_CS_HIGH;
master->flags = master_flags;
master->bus_num = pdev->id;
/* The master needs to think there is a chipselect even if not connected */
@@ -455,7 +456,6 @@
spi_gpio->bitbang.txrx_word[SPI_MODE_3] = spi_gpio_spec_txrx_word_mode3;
}
spi_gpio->bitbang.setup_transfer = spi_bitbang_setup_transfer;
- spi_gpio->bitbang.flags = SPI_CS_HIGH;
status = spi_bitbang_start(&spi_gpio->bitbang);
if (status)
diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index 5217a56..a4d8d19 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c
@@ -537,7 +537,6 @@
/**
* spi_mem_dirmap_destroy() - Destroy a direct mapping descriptor
* @desc: the direct mapping descriptor to destroy
- * @info: direct mapping information
*
* This function destroys a direct mapping descriptor previously created by
* spi_mem_dirmap_create().
@@ -548,9 +547,80 @@
if (!desc->nodirmap && ctlr->mem_ops && ctlr->mem_ops->dirmap_destroy)
ctlr->mem_ops->dirmap_destroy(desc);
+
+ kfree(desc);
}
EXPORT_SYMBOL_GPL(spi_mem_dirmap_destroy);
+static void devm_spi_mem_dirmap_release(struct device *dev, void *res)
+{
+ struct spi_mem_dirmap_desc *desc = *(struct spi_mem_dirmap_desc **)res;
+
+ spi_mem_dirmap_destroy(desc);
+}
+
+/**
+ * devm_spi_mem_dirmap_create() - Create a direct mapping descriptor and attach
+ * it to a device
+ * @dev: device the dirmap desc will be attached to
+ * @mem: SPI mem device this direct mapping should be created for
+ * @info: direct mapping information
+ *
+ * devm_ variant of the spi_mem_dirmap_create() function. See
+ * spi_mem_dirmap_create() for more details.
+ *
+ * Return: a valid pointer in case of success, and ERR_PTR() otherwise.
+ */
+struct spi_mem_dirmap_desc *
+devm_spi_mem_dirmap_create(struct device *dev, struct spi_mem *mem,
+ const struct spi_mem_dirmap_info *info)
+{
+ struct spi_mem_dirmap_desc **ptr, *desc;
+
+ ptr = devres_alloc(devm_spi_mem_dirmap_release, sizeof(*ptr),
+ GFP_KERNEL);
+ if (!ptr)
+ return ERR_PTR(-ENOMEM);
+
+ desc = spi_mem_dirmap_create(mem, info);
+ if (IS_ERR(desc)) {
+ devres_free(ptr);
+ } else {
+ *ptr = desc;
+ devres_add(dev, ptr);
+ }
+
+ return desc;
+}
+EXPORT_SYMBOL_GPL(devm_spi_mem_dirmap_create);
+
+static int devm_spi_mem_dirmap_match(struct device *dev, void *res, void *data)
+{
+ struct spi_mem_dirmap_desc **ptr = res;
+
+ if (WARN_ON(!ptr || !*ptr))
+ return 0;
+
+ return *ptr == data;
+}
+
+/**
+ * devm_spi_mem_dirmap_destroy() - Destroy a direct mapping descriptor attached
+ * to a device
+ * @dev: device the dirmap desc is attached to
+ * @desc: the direct mapping descriptor to destroy
+ *
+ * devm_ variant of the spi_mem_dirmap_destroy() function. See
+ * spi_mem_dirmap_destroy() for more details.
+ */
+void devm_spi_mem_dirmap_destroy(struct device *dev,
+ struct spi_mem_dirmap_desc *desc)
+{
+ devres_release(dev, devm_spi_mem_dirmap_release,
+ devm_spi_mem_dirmap_match, desc);
+}
+EXPORT_SYMBOL_GPL(devm_spi_mem_dirmap_destroy);
+
/**
* spi_mem_dirmap_dirmap_read() - Read data through a direct mapping
* @desc: direct mapping descriptor
diff --git a/drivers/spi/spi-mxs.c b/drivers/spi/spi-mxs.c
index 6ac95a2..7bf53cf 100644
--- a/drivers/spi/spi-mxs.c
+++ b/drivers/spi/spi-mxs.c
@@ -39,6 +39,7 @@
#include <linux/stmp_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/mxs-spi.h>
+#include <trace/events/spi.h>
#define DRIVER_NAME "mxs-spi"
@@ -374,6 +375,8 @@
list_for_each_entry(t, &m->transfers, transfer_list) {
+ trace_spi_transfer_start(m, t);
+
status = mxs_spi_setup_transfer(m->spi, t);
if (status)
break;
@@ -419,6 +422,8 @@
flag);
}
+ trace_spi_transfer_stop(m, t);
+
if (status) {
stmp_reset_block(ssp->base);
break;
diff --git a/drivers/spi/spi-npcm-pspi.c b/drivers/spi/spi-npcm-pspi.c
index e1dca79..734a2b95 100644
--- a/drivers/spi/spi-npcm-pspi.c
+++ b/drivers/spi/spi-npcm-pspi.c
@@ -465,7 +465,8 @@
static int npcm_pspi_remove(struct platform_device *pdev)
{
- struct npcm_pspi *priv = platform_get_drvdata(pdev);
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct npcm_pspi *priv = spi_master_get_devdata(master);
npcm_pspi_reset_hw(priv);
clk_disable_unprepare(priv->clk);
diff --git a/drivers/spi/spi-nxp-fspi.c b/drivers/spi/spi-nxp-fspi.c
new file mode 100644
index 0000000..8894f98
--- /dev/null
+++ b/drivers/spi/spi-nxp-fspi.c
@@ -0,0 +1,1106 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/*
+ * NXP FlexSPI(FSPI) controller driver.
+ *
+ * Copyright 2019 NXP.
+ *
+ * FlexSPI is a flexsible SPI host controller which supports two SPI
+ * channels and up to 4 external devices. Each channel supports
+ * Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional
+ * data lines).
+ *
+ * FlexSPI controller is driven by the LUT(Look-up Table) registers
+ * LUT registers are a look-up-table for sequences of instructions.
+ * A valid sequence consists of four LUT registers.
+ * Maximum 32 LUT sequences can be programmed simultaneously.
+ *
+ * LUTs are being created at run-time based on the commands passed
+ * from the spi-mem framework, thus using single LUT index.
+ *
+ * Software triggered Flash read/write access by IP Bus.
+ *
+ * Memory mapped read access by AHB Bus.
+ *
+ * Based on SPI MEM interface and spi-fsl-qspi.c driver.
+ *
+ * Author:
+ * Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
+ * Boris Brezillon <bbrezillon@kernel.org>
+ * Frieder Schrempf <frieder.schrempf@kontron.de>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_qos.h>
+#include <linux/sizes.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+/*
+ * The driver only uses one single LUT entry, that is updated on
+ * each call of exec_op(). Index 0 is preset at boot with a basic
+ * read operation, so let's use the last entry (31).
+ */
+#define SEQID_LUT 31
+
+/* Registers used by the driver */
+#define FSPI_MCR0 0x00
+#define FSPI_MCR0_AHB_TIMEOUT(x) ((x) << 24)
+#define FSPI_MCR0_IP_TIMEOUT(x) ((x) << 16)
+#define FSPI_MCR0_LEARN_EN BIT(15)
+#define FSPI_MCR0_SCRFRUN_EN BIT(14)
+#define FSPI_MCR0_OCTCOMB_EN BIT(13)
+#define FSPI_MCR0_DOZE_EN BIT(12)
+#define FSPI_MCR0_HSEN BIT(11)
+#define FSPI_MCR0_SERCLKDIV BIT(8)
+#define FSPI_MCR0_ATDF_EN BIT(7)
+#define FSPI_MCR0_ARDF_EN BIT(6)
+#define FSPI_MCR0_RXCLKSRC(x) ((x) << 4)
+#define FSPI_MCR0_END_CFG(x) ((x) << 2)
+#define FSPI_MCR0_MDIS BIT(1)
+#define FSPI_MCR0_SWRST BIT(0)
+
+#define FSPI_MCR1 0x04
+#define FSPI_MCR1_SEQ_TIMEOUT(x) ((x) << 16)
+#define FSPI_MCR1_AHB_TIMEOUT(x) (x)
+
+#define FSPI_MCR2 0x08
+#define FSPI_MCR2_IDLE_WAIT(x) ((x) << 24)
+#define FSPI_MCR2_SAMEDEVICEEN BIT(15)
+#define FSPI_MCR2_CLRLRPHS BIT(14)
+#define FSPI_MCR2_ABRDATSZ BIT(8)
+#define FSPI_MCR2_ABRLEARN BIT(7)
+#define FSPI_MCR2_ABR_READ BIT(6)
+#define FSPI_MCR2_ABRWRITE BIT(5)
+#define FSPI_MCR2_ABRDUMMY BIT(4)
+#define FSPI_MCR2_ABR_MODE BIT(3)
+#define FSPI_MCR2_ABRCADDR BIT(2)
+#define FSPI_MCR2_ABRRADDR BIT(1)
+#define FSPI_MCR2_ABR_CMD BIT(0)
+
+#define FSPI_AHBCR 0x0c
+#define FSPI_AHBCR_RDADDROPT BIT(6)
+#define FSPI_AHBCR_PREF_EN BIT(5)
+#define FSPI_AHBCR_BUFF_EN BIT(4)
+#define FSPI_AHBCR_CACH_EN BIT(3)
+#define FSPI_AHBCR_CLRTXBUF BIT(2)
+#define FSPI_AHBCR_CLRRXBUF BIT(1)
+#define FSPI_AHBCR_PAR_EN BIT(0)
+
+#define FSPI_INTEN 0x10
+#define FSPI_INTEN_SCLKSBWR BIT(9)
+#define FSPI_INTEN_SCLKSBRD BIT(8)
+#define FSPI_INTEN_DATALRNFL BIT(7)
+#define FSPI_INTEN_IPTXWE BIT(6)
+#define FSPI_INTEN_IPRXWA BIT(5)
+#define FSPI_INTEN_AHBCMDERR BIT(4)
+#define FSPI_INTEN_IPCMDERR BIT(3)
+#define FSPI_INTEN_AHBCMDGE BIT(2)
+#define FSPI_INTEN_IPCMDGE BIT(1)
+#define FSPI_INTEN_IPCMDDONE BIT(0)
+
+#define FSPI_INTR 0x14
+#define FSPI_INTR_SCLKSBWR BIT(9)
+#define FSPI_INTR_SCLKSBRD BIT(8)
+#define FSPI_INTR_DATALRNFL BIT(7)
+#define FSPI_INTR_IPTXWE BIT(6)
+#define FSPI_INTR_IPRXWA BIT(5)
+#define FSPI_INTR_AHBCMDERR BIT(4)
+#define FSPI_INTR_IPCMDERR BIT(3)
+#define FSPI_INTR_AHBCMDGE BIT(2)
+#define FSPI_INTR_IPCMDGE BIT(1)
+#define FSPI_INTR_IPCMDDONE BIT(0)
+
+#define FSPI_LUTKEY 0x18
+#define FSPI_LUTKEY_VALUE 0x5AF05AF0
+
+#define FSPI_LCKCR 0x1C
+
+#define FSPI_LCKER_LOCK 0x1
+#define FSPI_LCKER_UNLOCK 0x2
+
+#define FSPI_BUFXCR_INVALID_MSTRID 0xE
+#define FSPI_AHBRX_BUF0CR0 0x20
+#define FSPI_AHBRX_BUF1CR0 0x24
+#define FSPI_AHBRX_BUF2CR0 0x28
+#define FSPI_AHBRX_BUF3CR0 0x2C
+#define FSPI_AHBRX_BUF4CR0 0x30
+#define FSPI_AHBRX_BUF5CR0 0x34
+#define FSPI_AHBRX_BUF6CR0 0x38
+#define FSPI_AHBRX_BUF7CR0 0x3C
+#define FSPI_AHBRXBUF0CR7_PREF BIT(31)
+
+#define FSPI_AHBRX_BUF0CR1 0x40
+#define FSPI_AHBRX_BUF1CR1 0x44
+#define FSPI_AHBRX_BUF2CR1 0x48
+#define FSPI_AHBRX_BUF3CR1 0x4C
+#define FSPI_AHBRX_BUF4CR1 0x50
+#define FSPI_AHBRX_BUF5CR1 0x54
+#define FSPI_AHBRX_BUF6CR1 0x58
+#define FSPI_AHBRX_BUF7CR1 0x5C
+
+#define FSPI_FLSHA1CR0 0x60
+#define FSPI_FLSHA2CR0 0x64
+#define FSPI_FLSHB1CR0 0x68
+#define FSPI_FLSHB2CR0 0x6C
+#define FSPI_FLSHXCR0_SZ_KB 10
+#define FSPI_FLSHXCR0_SZ(x) ((x) >> FSPI_FLSHXCR0_SZ_KB)
+
+#define FSPI_FLSHA1CR1 0x70
+#define FSPI_FLSHA2CR1 0x74
+#define FSPI_FLSHB1CR1 0x78
+#define FSPI_FLSHB2CR1 0x7C
+#define FSPI_FLSHXCR1_CSINTR(x) ((x) << 16)
+#define FSPI_FLSHXCR1_CAS(x) ((x) << 11)
+#define FSPI_FLSHXCR1_WA BIT(10)
+#define FSPI_FLSHXCR1_TCSH(x) ((x) << 5)
+#define FSPI_FLSHXCR1_TCSS(x) (x)
+
+#define FSPI_FLSHA1CR2 0x80
+#define FSPI_FLSHA2CR2 0x84
+#define FSPI_FLSHB1CR2 0x88
+#define FSPI_FLSHB2CR2 0x8C
+#define FSPI_FLSHXCR2_CLRINSP BIT(24)
+#define FSPI_FLSHXCR2_AWRWAIT BIT(16)
+#define FSPI_FLSHXCR2_AWRSEQN_SHIFT 13
+#define FSPI_FLSHXCR2_AWRSEQI_SHIFT 8
+#define FSPI_FLSHXCR2_ARDSEQN_SHIFT 5
+#define FSPI_FLSHXCR2_ARDSEQI_SHIFT 0
+
+#define FSPI_IPCR0 0xA0
+
+#define FSPI_IPCR1 0xA4
+#define FSPI_IPCR1_IPAREN BIT(31)
+#define FSPI_IPCR1_SEQNUM_SHIFT 24
+#define FSPI_IPCR1_SEQID_SHIFT 16
+#define FSPI_IPCR1_IDATSZ(x) (x)
+
+#define FSPI_IPCMD 0xB0
+#define FSPI_IPCMD_TRG BIT(0)
+
+#define FSPI_DLPR 0xB4
+
+#define FSPI_IPRXFCR 0xB8
+#define FSPI_IPRXFCR_CLR BIT(0)
+#define FSPI_IPRXFCR_DMA_EN BIT(1)
+#define FSPI_IPRXFCR_WMRK(x) ((x) << 2)
+
+#define FSPI_IPTXFCR 0xBC
+#define FSPI_IPTXFCR_CLR BIT(0)
+#define FSPI_IPTXFCR_DMA_EN BIT(1)
+#define FSPI_IPTXFCR_WMRK(x) ((x) << 2)
+
+#define FSPI_DLLACR 0xC0
+#define FSPI_DLLACR_OVRDEN BIT(8)
+
+#define FSPI_DLLBCR 0xC4
+#define FSPI_DLLBCR_OVRDEN BIT(8)
+
+#define FSPI_STS0 0xE0
+#define FSPI_STS0_DLPHB(x) ((x) << 8)
+#define FSPI_STS0_DLPHA(x) ((x) << 4)
+#define FSPI_STS0_CMD_SRC(x) ((x) << 2)
+#define FSPI_STS0_ARB_IDLE BIT(1)
+#define FSPI_STS0_SEQ_IDLE BIT(0)
+
+#define FSPI_STS1 0xE4
+#define FSPI_STS1_IP_ERRCD(x) ((x) << 24)
+#define FSPI_STS1_IP_ERRID(x) ((x) << 16)
+#define FSPI_STS1_AHB_ERRCD(x) ((x) << 8)
+#define FSPI_STS1_AHB_ERRID(x) (x)
+
+#define FSPI_AHBSPNST 0xEC
+#define FSPI_AHBSPNST_DATLFT(x) ((x) << 16)
+#define FSPI_AHBSPNST_BUFID(x) ((x) << 1)
+#define FSPI_AHBSPNST_ACTIVE BIT(0)
+
+#define FSPI_IPRXFSTS 0xF0
+#define FSPI_IPRXFSTS_RDCNTR(x) ((x) << 16)
+#define FSPI_IPRXFSTS_FILL(x) (x)
+
+#define FSPI_IPTXFSTS 0xF4
+#define FSPI_IPTXFSTS_WRCNTR(x) ((x) << 16)
+#define FSPI_IPTXFSTS_FILL(x) (x)
+
+#define FSPI_RFDR 0x100
+#define FSPI_TFDR 0x180
+
+#define FSPI_LUT_BASE 0x200
+#define FSPI_LUT_OFFSET (SEQID_LUT * 4 * 4)
+#define FSPI_LUT_REG(idx) \
+ (FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4)
+
+/* register map end */
+
+/* Instruction set for the LUT register. */
+#define LUT_STOP 0x00
+#define LUT_CMD 0x01
+#define LUT_ADDR 0x02
+#define LUT_CADDR_SDR 0x03
+#define LUT_MODE 0x04
+#define LUT_MODE2 0x05
+#define LUT_MODE4 0x06
+#define LUT_MODE8 0x07
+#define LUT_NXP_WRITE 0x08
+#define LUT_NXP_READ 0x09
+#define LUT_LEARN_SDR 0x0A
+#define LUT_DATSZ_SDR 0x0B
+#define LUT_DUMMY 0x0C
+#define LUT_DUMMY_RWDS_SDR 0x0D
+#define LUT_JMP_ON_CS 0x1F
+#define LUT_CMD_DDR 0x21
+#define LUT_ADDR_DDR 0x22
+#define LUT_CADDR_DDR 0x23
+#define LUT_MODE_DDR 0x24
+#define LUT_MODE2_DDR 0x25
+#define LUT_MODE4_DDR 0x26
+#define LUT_MODE8_DDR 0x27
+#define LUT_WRITE_DDR 0x28
+#define LUT_READ_DDR 0x29
+#define LUT_LEARN_DDR 0x2A
+#define LUT_DATSZ_DDR 0x2B
+#define LUT_DUMMY_DDR 0x2C
+#define LUT_DUMMY_RWDS_DDR 0x2D
+
+/*
+ * Calculate number of required PAD bits for LUT register.
+ *
+ * The pad stands for the number of IO lines [0:7].
+ * For example, the octal read needs eight IO lines,
+ * so you should use LUT_PAD(8). This macro
+ * returns 3 i.e. use eight (2^3) IP lines for read.
+ */
+#define LUT_PAD(x) (fls(x) - 1)
+
+/*
+ * Macro for constructing the LUT entries with the following
+ * register layout:
+ *
+ * ---------------------------------------------------
+ * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
+ * ---------------------------------------------------
+ */
+#define PAD_SHIFT 8
+#define INSTR_SHIFT 10
+#define OPRND_SHIFT 16
+
+/* Macros for constructing the LUT register. */
+#define LUT_DEF(idx, ins, pad, opr) \
+ ((((ins) << INSTR_SHIFT) | ((pad) << PAD_SHIFT) | \
+ (opr)) << (((idx) % 2) * OPRND_SHIFT))
+
+#define POLL_TOUT 5000
+#define NXP_FSPI_MAX_CHIPSELECT 4
+
+struct nxp_fspi_devtype_data {
+ unsigned int rxfifo;
+ unsigned int txfifo;
+ unsigned int ahb_buf_size;
+ unsigned int quirks;
+ bool little_endian;
+};
+
+static const struct nxp_fspi_devtype_data lx2160a_data = {
+ .rxfifo = SZ_512, /* (64 * 64 bits) */
+ .txfifo = SZ_1K, /* (128 * 64 bits) */
+ .ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
+ .quirks = 0,
+ .little_endian = true, /* little-endian */
+};
+
+struct nxp_fspi {
+ void __iomem *iobase;
+ void __iomem *ahb_addr;
+ u32 memmap_phy;
+ u32 memmap_phy_size;
+ struct clk *clk, *clk_en;
+ struct device *dev;
+ struct completion c;
+ const struct nxp_fspi_devtype_data *devtype_data;
+ struct mutex lock;
+ struct pm_qos_request pm_qos_req;
+ int selected;
+};
+
+/*
+ * R/W functions for big- or little-endian registers:
+ * The FSPI controller's endianness is independent of
+ * the CPU core's endianness. So far, although the CPU
+ * core is little-endian the FSPI controller can use
+ * big-endian or little-endian.
+ */
+static void fspi_writel(struct nxp_fspi *f, u32 val, void __iomem *addr)
+{
+ if (f->devtype_data->little_endian)
+ iowrite32(val, addr);
+ else
+ iowrite32be(val, addr);
+}
+
+static u32 fspi_readl(struct nxp_fspi *f, void __iomem *addr)
+{
+ if (f->devtype_data->little_endian)
+ return ioread32(addr);
+ else
+ return ioread32be(addr);
+}
+
+static irqreturn_t nxp_fspi_irq_handler(int irq, void *dev_id)
+{
+ struct nxp_fspi *f = dev_id;
+ u32 reg;
+
+ /* clear interrupt */
+ reg = fspi_readl(f, f->iobase + FSPI_INTR);
+ fspi_writel(f, FSPI_INTR_IPCMDDONE, f->iobase + FSPI_INTR);
+
+ if (reg & FSPI_INTR_IPCMDDONE)
+ complete(&f->c);
+
+ return IRQ_HANDLED;
+}
+
+static int nxp_fspi_check_buswidth(struct nxp_fspi *f, u8 width)
+{
+ switch (width) {
+ case 1:
+ case 2:
+ case 4:
+ case 8:
+ return 0;
+ }
+
+ return -ENOTSUPP;
+}
+
+static bool nxp_fspi_supports_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+ int ret;
+
+ ret = nxp_fspi_check_buswidth(f, op->cmd.buswidth);
+
+ if (op->addr.nbytes)
+ ret |= nxp_fspi_check_buswidth(f, op->addr.buswidth);
+
+ if (op->dummy.nbytes)
+ ret |= nxp_fspi_check_buswidth(f, op->dummy.buswidth);
+
+ if (op->data.nbytes)
+ ret |= nxp_fspi_check_buswidth(f, op->data.buswidth);
+
+ if (ret)
+ return false;
+
+ /*
+ * The number of address bytes should be equal to or less than 4 bytes.
+ */
+ if (op->addr.nbytes > 4)
+ return false;
+
+ /*
+ * If requested address value is greater than controller assigned
+ * memory mapped space, return error as it didn't fit in the range
+ * of assigned address space.
+ */
+ if (op->addr.val >= f->memmap_phy_size)
+ return false;
+
+ /* Max 64 dummy clock cycles supported */
+ if (op->dummy.buswidth &&
+ (op->dummy.nbytes * 8 / op->dummy.buswidth > 64))
+ return false;
+
+ /* Max data length, check controller limits and alignment */
+ if (op->data.dir == SPI_MEM_DATA_IN &&
+ (op->data.nbytes > f->devtype_data->ahb_buf_size ||
+ (op->data.nbytes > f->devtype_data->rxfifo - 4 &&
+ !IS_ALIGNED(op->data.nbytes, 8))))
+ return false;
+
+ if (op->data.dir == SPI_MEM_DATA_OUT &&
+ op->data.nbytes > f->devtype_data->txfifo)
+ return false;
+
+ return true;
+}
+
+/* Instead of busy looping invoke readl_poll_timeout functionality. */
+static int fspi_readl_poll_tout(struct nxp_fspi *f, void __iomem *base,
+ u32 mask, u32 delay_us,
+ u32 timeout_us, bool c)
+{
+ u32 reg;
+
+ if (!f->devtype_data->little_endian)
+ mask = (u32)cpu_to_be32(mask);
+
+ if (c)
+ return readl_poll_timeout(base, reg, (reg & mask),
+ delay_us, timeout_us);
+ else
+ return readl_poll_timeout(base, reg, !(reg & mask),
+ delay_us, timeout_us);
+}
+
+/*
+ * If the slave device content being changed by Write/Erase, need to
+ * invalidate the AHB buffer. This can be achieved by doing the reset
+ * of controller after setting MCR0[SWRESET] bit.
+ */
+static inline void nxp_fspi_invalid(struct nxp_fspi *f)
+{
+ u32 reg;
+ int ret;
+
+ reg = fspi_readl(f, f->iobase + FSPI_MCR0);
+ fspi_writel(f, reg | FSPI_MCR0_SWRST, f->iobase + FSPI_MCR0);
+
+ /* w1c register, wait unit clear */
+ ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
+ FSPI_MCR0_SWRST, 0, POLL_TOUT, false);
+ WARN_ON(ret);
+}
+
+static void nxp_fspi_prepare_lut(struct nxp_fspi *f,
+ const struct spi_mem_op *op)
+{
+ void __iomem *base = f->iobase;
+ u32 lutval[4] = {};
+ int lutidx = 1, i;
+
+ /* cmd */
+ lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth),
+ op->cmd.opcode);
+
+ /* addr bytes */
+ if (op->addr.nbytes) {
+ lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_ADDR,
+ LUT_PAD(op->addr.buswidth),
+ op->addr.nbytes * 8);
+ lutidx++;
+ }
+
+ /* dummy bytes, if needed */
+ if (op->dummy.nbytes) {
+ lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY,
+ /*
+ * Due to FlexSPI controller limitation number of PAD for dummy
+ * buswidth needs to be programmed as equal to data buswidth.
+ */
+ LUT_PAD(op->data.buswidth),
+ op->dummy.nbytes * 8 /
+ op->dummy.buswidth);
+ lutidx++;
+ }
+
+ /* read/write data bytes */
+ if (op->data.nbytes) {
+ lutval[lutidx / 2] |= LUT_DEF(lutidx,
+ op->data.dir == SPI_MEM_DATA_IN ?
+ LUT_NXP_READ : LUT_NXP_WRITE,
+ LUT_PAD(op->data.buswidth),
+ 0);
+ lutidx++;
+ }
+
+ /* stop condition. */
+ lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0);
+
+ /* unlock LUT */
+ fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
+ fspi_writel(f, FSPI_LCKER_UNLOCK, f->iobase + FSPI_LCKCR);
+
+ /* fill LUT */
+ for (i = 0; i < ARRAY_SIZE(lutval); i++)
+ fspi_writel(f, lutval[i], base + FSPI_LUT_REG(i));
+
+ dev_dbg(f->dev, "CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x]\n",
+ op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3]);
+
+ /* lock LUT */
+ fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
+ fspi_writel(f, FSPI_LCKER_LOCK, f->iobase + FSPI_LCKCR);
+}
+
+static int nxp_fspi_clk_prep_enable(struct nxp_fspi *f)
+{
+ int ret;
+
+ ret = clk_prepare_enable(f->clk_en);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(f->clk);
+ if (ret) {
+ clk_disable_unprepare(f->clk_en);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void nxp_fspi_clk_disable_unprep(struct nxp_fspi *f)
+{
+ clk_disable_unprepare(f->clk);
+ clk_disable_unprepare(f->clk_en);
+}
+
+/*
+ * In FlexSPI controller, flash access is based on value of FSPI_FLSHXXCR0
+ * register and start base address of the slave device.
+ *
+ * (Higher address)
+ * -------- <-- FLSHB2CR0
+ * | B2 |
+ * | |
+ * B2 start address --> -------- <-- FLSHB1CR0
+ * | B1 |
+ * | |
+ * B1 start address --> -------- <-- FLSHA2CR0
+ * | A2 |
+ * | |
+ * A2 start address --> -------- <-- FLSHA1CR0
+ * | A1 |
+ * | |
+ * A1 start address --> -------- (Lower address)
+ *
+ *
+ * Start base address defines the starting address range for given CS and
+ * FSPI_FLSHXXCR0 defines the size of the slave device connected at given CS.
+ *
+ * But, different targets are having different combinations of number of CS,
+ * some targets only have single CS or two CS covering controller's full
+ * memory mapped space area.
+ * Thus, implementation is being done as independent of the size and number
+ * of the connected slave device.
+ * Assign controller memory mapped space size as the size to the connected
+ * slave device.
+ * Mark FLSHxxCR0 as zero initially and then assign value only to the selected
+ * chip-select Flash configuration register.
+ *
+ * For e.g. to access CS2 (B1), FLSHB1CR0 register would be equal to the
+ * memory mapped size of the controller.
+ * Value for rest of the CS FLSHxxCR0 register would be zero.
+ *
+ */
+static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi)
+{
+ unsigned long rate = spi->max_speed_hz;
+ int ret;
+ uint64_t size_kb;
+
+ /*
+ * Return, if previously selected slave device is same as current
+ * requested slave device.
+ */
+ if (f->selected == spi->chip_select)
+ return;
+
+ /* Reset FLSHxxCR0 registers */
+ fspi_writel(f, 0, f->iobase + FSPI_FLSHA1CR0);
+ fspi_writel(f, 0, f->iobase + FSPI_FLSHA2CR0);
+ fspi_writel(f, 0, f->iobase + FSPI_FLSHB1CR0);
+ fspi_writel(f, 0, f->iobase + FSPI_FLSHB2CR0);
+
+ /* Assign controller memory mapped space as size, KBytes, of flash. */
+ size_kb = FSPI_FLSHXCR0_SZ(f->memmap_phy_size);
+
+ fspi_writel(f, size_kb, f->iobase + FSPI_FLSHA1CR0 +
+ 4 * spi->chip_select);
+
+ dev_dbg(f->dev, "Slave device [CS:%x] selected\n", spi->chip_select);
+
+ nxp_fspi_clk_disable_unprep(f);
+
+ ret = clk_set_rate(f->clk, rate);
+ if (ret)
+ return;
+
+ ret = nxp_fspi_clk_prep_enable(f);
+ if (ret)
+ return;
+
+ f->selected = spi->chip_select;
+}
+
+static void nxp_fspi_read_ahb(struct nxp_fspi *f, const struct spi_mem_op *op)
+{
+ u32 len = op->data.nbytes;
+
+ /* Read out the data directly from the AHB buffer. */
+ memcpy_fromio(op->data.buf.in, (f->ahb_addr + op->addr.val), len);
+}
+
+static void nxp_fspi_fill_txfifo(struct nxp_fspi *f,
+ const struct spi_mem_op *op)
+{
+ void __iomem *base = f->iobase;
+ int i, ret;
+ u8 *buf = (u8 *) op->data.buf.out;
+
+ /* clear the TX FIFO. */
+ fspi_writel(f, FSPI_IPTXFCR_CLR, base + FSPI_IPTXFCR);
+
+ /*
+ * Default value of water mark level is 8 bytes, hence in single
+ * write request controller can write max 8 bytes of data.
+ */
+
+ for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 8); i += 8) {
+ /* Wait for TXFIFO empty */
+ ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+ FSPI_INTR_IPTXWE, 0,
+ POLL_TOUT, true);
+ WARN_ON(ret);
+
+ fspi_writel(f, *(u32 *) (buf + i), base + FSPI_TFDR);
+ fspi_writel(f, *(u32 *) (buf + i + 4), base + FSPI_TFDR + 4);
+ fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
+ }
+
+ if (i < op->data.nbytes) {
+ u32 data = 0;
+ int j;
+ /* Wait for TXFIFO empty */
+ ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+ FSPI_INTR_IPTXWE, 0,
+ POLL_TOUT, true);
+ WARN_ON(ret);
+
+ for (j = 0; j < ALIGN(op->data.nbytes - i, 4); j += 4) {
+ memcpy(&data, buf + i + j, 4);
+ fspi_writel(f, data, base + FSPI_TFDR + j);
+ }
+ fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
+ }
+}
+
+static void nxp_fspi_read_rxfifo(struct nxp_fspi *f,
+ const struct spi_mem_op *op)
+{
+ void __iomem *base = f->iobase;
+ int i, ret;
+ int len = op->data.nbytes;
+ u8 *buf = (u8 *) op->data.buf.in;
+
+ /*
+ * Default value of water mark level is 8 bytes, hence in single
+ * read request controller can read max 8 bytes of data.
+ */
+ for (i = 0; i < ALIGN_DOWN(len, 8); i += 8) {
+ /* Wait for RXFIFO available */
+ ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+ FSPI_INTR_IPRXWA, 0,
+ POLL_TOUT, true);
+ WARN_ON(ret);
+
+ *(u32 *)(buf + i) = fspi_readl(f, base + FSPI_RFDR);
+ *(u32 *)(buf + i + 4) = fspi_readl(f, base + FSPI_RFDR + 4);
+ /* move the FIFO pointer */
+ fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR);
+ }
+
+ if (i < len) {
+ u32 tmp;
+ int size, j;
+
+ buf = op->data.buf.in + i;
+ /* Wait for RXFIFO available */
+ ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
+ FSPI_INTR_IPRXWA, 0,
+ POLL_TOUT, true);
+ WARN_ON(ret);
+
+ len = op->data.nbytes - i;
+ for (j = 0; j < op->data.nbytes - i; j += 4) {
+ tmp = fspi_readl(f, base + FSPI_RFDR + j);
+ size = min(len, 4);
+ memcpy(buf + j, &tmp, size);
+ len -= size;
+ }
+ }
+
+ /* invalid the RXFIFO */
+ fspi_writel(f, FSPI_IPRXFCR_CLR, base + FSPI_IPRXFCR);
+ /* move the FIFO pointer */
+ fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR);
+}
+
+static int nxp_fspi_do_op(struct nxp_fspi *f, const struct spi_mem_op *op)
+{
+ void __iomem *base = f->iobase;
+ int seqnum = 0;
+ int err = 0;
+ u32 reg;
+
+ reg = fspi_readl(f, base + FSPI_IPRXFCR);
+ /* invalid RXFIFO first */
+ reg &= ~FSPI_IPRXFCR_DMA_EN;
+ reg = reg | FSPI_IPRXFCR_CLR;
+ fspi_writel(f, reg, base + FSPI_IPRXFCR);
+
+ init_completion(&f->c);
+
+ fspi_writel(f, op->addr.val, base + FSPI_IPCR0);
+ /*
+ * Always start the sequence at the same index since we update
+ * the LUT at each exec_op() call. And also specify the DATA
+ * length, since it's has not been specified in the LUT.
+ */
+ fspi_writel(f, op->data.nbytes |
+ (SEQID_LUT << FSPI_IPCR1_SEQID_SHIFT) |
+ (seqnum << FSPI_IPCR1_SEQNUM_SHIFT),
+ base + FSPI_IPCR1);
+
+ /* Trigger the LUT now. */
+ fspi_writel(f, FSPI_IPCMD_TRG, base + FSPI_IPCMD);
+
+ /* Wait for the interrupt. */
+ if (!wait_for_completion_timeout(&f->c, msecs_to_jiffies(1000)))
+ err = -ETIMEDOUT;
+
+ /* Invoke IP data read, if request is of data read. */
+ if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN)
+ nxp_fspi_read_rxfifo(f, op);
+
+ return err;
+}
+
+static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+ int err = 0;
+
+ mutex_lock(&f->lock);
+
+ /* Wait for controller being ready. */
+ err = fspi_readl_poll_tout(f, f->iobase + FSPI_STS0,
+ FSPI_STS0_ARB_IDLE, 1, POLL_TOUT, true);
+ WARN_ON(err);
+
+ nxp_fspi_select_mem(f, mem->spi);
+
+ nxp_fspi_prepare_lut(f, op);
+ /*
+ * If we have large chunks of data, we read them through the AHB bus
+ * by accessing the mapped memory. In all other cases we use
+ * IP commands to access the flash.
+ */
+ if (op->data.nbytes > (f->devtype_data->rxfifo - 4) &&
+ op->data.dir == SPI_MEM_DATA_IN) {
+ nxp_fspi_read_ahb(f, op);
+ } else {
+ if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
+ nxp_fspi_fill_txfifo(f, op);
+
+ err = nxp_fspi_do_op(f, op);
+ }
+
+ /* Invalidate the data in the AHB buffer. */
+ nxp_fspi_invalid(f);
+
+ mutex_unlock(&f->lock);
+
+ return err;
+}
+
+static int nxp_fspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
+{
+ struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+
+ if (op->data.dir == SPI_MEM_DATA_OUT) {
+ if (op->data.nbytes > f->devtype_data->txfifo)
+ op->data.nbytes = f->devtype_data->txfifo;
+ } else {
+ if (op->data.nbytes > f->devtype_data->ahb_buf_size)
+ op->data.nbytes = f->devtype_data->ahb_buf_size;
+ else if (op->data.nbytes > (f->devtype_data->rxfifo - 4))
+ op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8);
+ }
+
+ return 0;
+}
+
+static int nxp_fspi_default_setup(struct nxp_fspi *f)
+{
+ void __iomem *base = f->iobase;
+ int ret, i;
+ u32 reg;
+
+ /* disable and unprepare clock to avoid glitch pass to controller */
+ nxp_fspi_clk_disable_unprep(f);
+
+ /* the default frequency, we will change it later if necessary. */
+ ret = clk_set_rate(f->clk, 20000000);
+ if (ret)
+ return ret;
+
+ ret = nxp_fspi_clk_prep_enable(f);
+ if (ret)
+ return ret;
+
+ /* Reset the module */
+ /* w1c register, wait unit clear */
+ ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
+ FSPI_MCR0_SWRST, 0, POLL_TOUT, false);
+ WARN_ON(ret);
+
+ /* Disable the module */
+ fspi_writel(f, FSPI_MCR0_MDIS, base + FSPI_MCR0);
+
+ /* Reset the DLL register to default value */
+ fspi_writel(f, FSPI_DLLACR_OVRDEN, base + FSPI_DLLACR);
+ fspi_writel(f, FSPI_DLLBCR_OVRDEN, base + FSPI_DLLBCR);
+
+ /* enable module */
+ fspi_writel(f, FSPI_MCR0_AHB_TIMEOUT(0xFF) | FSPI_MCR0_IP_TIMEOUT(0xFF),
+ base + FSPI_MCR0);
+
+ /*
+ * Disable same device enable bit and configure all slave devices
+ * independently.
+ */
+ reg = fspi_readl(f, f->iobase + FSPI_MCR2);
+ reg = reg & ~(FSPI_MCR2_SAMEDEVICEEN);
+ fspi_writel(f, reg, base + FSPI_MCR2);
+
+ /* AHB configuration for access buffer 0~7. */
+ for (i = 0; i < 7; i++)
+ fspi_writel(f, 0, base + FSPI_AHBRX_BUF0CR0 + 4 * i);
+
+ /*
+ * Set ADATSZ with the maximum AHB buffer size to improve the read
+ * performance.
+ */
+ fspi_writel(f, (f->devtype_data->ahb_buf_size / 8 |
+ FSPI_AHBRXBUF0CR7_PREF), base + FSPI_AHBRX_BUF7CR0);
+
+ /* prefetch and no start address alignment limitation */
+ fspi_writel(f, FSPI_AHBCR_PREF_EN | FSPI_AHBCR_RDADDROPT,
+ base + FSPI_AHBCR);
+
+ /* AHB Read - Set lut sequence ID for all CS. */
+ fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA1CR2);
+ fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA2CR2);
+ fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB1CR2);
+ fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB2CR2);
+
+ f->selected = -1;
+
+ /* enable the interrupt */
+ fspi_writel(f, FSPI_INTEN_IPCMDDONE, base + FSPI_INTEN);
+
+ return 0;
+}
+
+static const char *nxp_fspi_get_name(struct spi_mem *mem)
+{
+ struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
+ struct device *dev = &mem->spi->dev;
+ const char *name;
+
+ // Set custom name derived from the platform_device of the controller.
+ if (of_get_available_child_count(f->dev->of_node) == 1)
+ return dev_name(f->dev);
+
+ name = devm_kasprintf(dev, GFP_KERNEL,
+ "%s-%d", dev_name(f->dev),
+ mem->spi->chip_select);
+
+ if (!name) {
+ dev_err(dev, "failed to get memory for custom flash name\n");
+ return ERR_PTR(-ENOMEM);
+ }
+
+ return name;
+}
+
+static const struct spi_controller_mem_ops nxp_fspi_mem_ops = {
+ .adjust_op_size = nxp_fspi_adjust_op_size,
+ .supports_op = nxp_fspi_supports_op,
+ .exec_op = nxp_fspi_exec_op,
+ .get_name = nxp_fspi_get_name,
+};
+
+static int nxp_fspi_probe(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct resource *res;
+ struct nxp_fspi *f;
+ int ret;
+
+ ctlr = spi_alloc_master(&pdev->dev, sizeof(*f));
+ if (!ctlr)
+ return -ENOMEM;
+
+ ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL |
+ SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL;
+
+ f = spi_controller_get_devdata(ctlr);
+ f->dev = dev;
+ f->devtype_data = of_device_get_match_data(dev);
+ if (!f->devtype_data) {
+ ret = -ENODEV;
+ goto err_put_ctrl;
+ }
+
+ platform_set_drvdata(pdev, f);
+
+ /* find the resources - configuration register address space */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fspi_base");
+ f->iobase = devm_ioremap_resource(dev, res);
+ if (IS_ERR(f->iobase)) {
+ ret = PTR_ERR(f->iobase);
+ goto err_put_ctrl;
+ }
+
+ /* find the resources - controller memory mapped space */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fspi_mmap");
+ f->ahb_addr = devm_ioremap_resource(dev, res);
+ if (IS_ERR(f->ahb_addr)) {
+ ret = PTR_ERR(f->ahb_addr);
+ goto err_put_ctrl;
+ }
+
+ /* assign memory mapped starting address and mapped size. */
+ f->memmap_phy = res->start;
+ f->memmap_phy_size = resource_size(res);
+
+ /* find the clocks */
+ f->clk_en = devm_clk_get(dev, "fspi_en");
+ if (IS_ERR(f->clk_en)) {
+ ret = PTR_ERR(f->clk_en);
+ goto err_put_ctrl;
+ }
+
+ f->clk = devm_clk_get(dev, "fspi");
+ if (IS_ERR(f->clk)) {
+ ret = PTR_ERR(f->clk);
+ goto err_put_ctrl;
+ }
+
+ ret = nxp_fspi_clk_prep_enable(f);
+ if (ret) {
+ dev_err(dev, "can not enable the clock\n");
+ goto err_put_ctrl;
+ }
+
+ /* find the irq */
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0) {
+ dev_err(dev, "failed to get the irq: %d\n", ret);
+ goto err_disable_clk;
+ }
+
+ ret = devm_request_irq(dev, ret,
+ nxp_fspi_irq_handler, 0, pdev->name, f);
+ if (ret) {
+ dev_err(dev, "failed to request irq: %d\n", ret);
+ goto err_disable_clk;
+ }
+
+ mutex_init(&f->lock);
+
+ ctlr->bus_num = -1;
+ ctlr->num_chipselect = NXP_FSPI_MAX_CHIPSELECT;
+ ctlr->mem_ops = &nxp_fspi_mem_ops;
+
+ nxp_fspi_default_setup(f);
+
+ ctlr->dev.of_node = np;
+
+ ret = spi_register_controller(ctlr);
+ if (ret)
+ goto err_destroy_mutex;
+
+ return 0;
+
+err_destroy_mutex:
+ mutex_destroy(&f->lock);
+
+err_disable_clk:
+ nxp_fspi_clk_disable_unprep(f);
+
+err_put_ctrl:
+ spi_controller_put(ctlr);
+
+ dev_err(dev, "NXP FSPI probe failed\n");
+ return ret;
+}
+
+static int nxp_fspi_remove(struct platform_device *pdev)
+{
+ struct nxp_fspi *f = platform_get_drvdata(pdev);
+
+ /* disable the hardware */
+ fspi_writel(f, FSPI_MCR0_MDIS, f->iobase + FSPI_MCR0);
+
+ nxp_fspi_clk_disable_unprep(f);
+
+ mutex_destroy(&f->lock);
+
+ return 0;
+}
+
+static int nxp_fspi_suspend(struct device *dev)
+{
+ return 0;
+}
+
+static int nxp_fspi_resume(struct device *dev)
+{
+ struct nxp_fspi *f = dev_get_drvdata(dev);
+
+ nxp_fspi_default_setup(f);
+
+ return 0;
+}
+
+static const struct of_device_id nxp_fspi_dt_ids[] = {
+ { .compatible = "nxp,lx2160a-fspi", .data = (void *)&lx2160a_data, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, nxp_fspi_dt_ids);
+
+static const struct dev_pm_ops nxp_fspi_pm_ops = {
+ .suspend = nxp_fspi_suspend,
+ .resume = nxp_fspi_resume,
+};
+
+static struct platform_driver nxp_fspi_driver = {
+ .driver = {
+ .name = "nxp-fspi",
+ .of_match_table = nxp_fspi_dt_ids,
+ .pm = &nxp_fspi_pm_ops,
+ },
+ .probe = nxp_fspi_probe,
+ .remove = nxp_fspi_remove,
+};
+module_platform_driver(nxp_fspi_driver);
+
+MODULE_DESCRIPTION("NXP FSPI Controller Driver");
+MODULE_AUTHOR("NXP Semiconductor");
+MODULE_AUTHOR("Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>");
+MODULE_AUTHOR("Boris Brezillon <bbrezillon@kernel.org>");
+MODULE_AUTHOR("Frieder Schrempf <frieder.schrempf@kontron.de>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 2fd8881..8be3043 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -623,8 +623,8 @@
cfg.dst_addr = cs->phys + OMAP2_MCSPI_TX0;
cfg.src_addr_width = width;
cfg.dst_addr_width = width;
- cfg.src_maxburst = es;
- cfg.dst_maxburst = es;
+ cfg.src_maxburst = 1;
+ cfg.dst_maxburst = 1;
rx = xfer->rx_buf;
tx = xfer->tx_buf;
diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c
index 0c793e3..2668417 100644
--- a/drivers/spi/spi-pl022.c
+++ b/drivers/spi/spi-pl022.c
@@ -253,6 +253,7 @@
#define STATE_RUNNING ((void *) 1)
#define STATE_DONE ((void *) 2)
#define STATE_ERROR ((void *) -1)
+#define STATE_TIMEOUT ((void *) -2)
/*
* SSP State - Whether Enabled or Disabled
@@ -1484,6 +1485,30 @@
writew(irqflags, SSP_IMSC(pl022->virtbase));
}
+static void print_current_status(struct pl022 *pl022)
+{
+ u32 read_cr0;
+ u16 read_cr1, read_dmacr, read_sr;
+
+ if (pl022->vendor->extended_cr)
+ read_cr0 = readl(SSP_CR0(pl022->virtbase));
+ else
+ read_cr0 = readw(SSP_CR0(pl022->virtbase));
+ read_cr1 = readw(SSP_CR1(pl022->virtbase));
+ read_dmacr = readw(SSP_DMACR(pl022->virtbase));
+ read_sr = readw(SSP_SR(pl022->virtbase));
+
+ dev_warn(&pl022->adev->dev, "spi-pl022 CR0: %x\n", read_cr0);
+ dev_warn(&pl022->adev->dev, "spi-pl022 CR1: %x\n", read_cr1);
+ dev_warn(&pl022->adev->dev, "spi-pl022 DMACR: %x\n", read_dmacr);
+ dev_warn(&pl022->adev->dev, "spi-pl022 SR: %x\n", read_sr);
+ dev_warn(&pl022->adev->dev,
+ "spi-pl022 exp_fifo_level/fifodepth: %u/%d\n",
+ pl022->exp_fifo_level,
+ pl022->vendor->fifodepth);
+
+}
+
static void do_polling_transfer(struct pl022 *pl022)
{
struct spi_message *message = NULL;
@@ -1535,7 +1560,8 @@
if (time_after(time, timeout)) {
dev_warn(&pl022->adev->dev,
"%s: timeout!\n", __func__);
- message->state = STATE_ERROR;
+ message->state = STATE_TIMEOUT;
+ print_current_status(pl022);
goto out;
}
cpu_relax();
@@ -1553,6 +1579,8 @@
/* Handle end of message */
if (message->state == STATE_DONE)
message->status = 0;
+ else if (message->state == STATE_TIMEOUT)
+ message->status = -EAGAIN;
else
message->status = -EIO;
diff --git a/drivers/spi/spi-pxa2xx-dma.c b/drivers/spi/spi-pxa2xx-dma.c
index 2fa7f4b..1559259 100644
--- a/drivers/spi/spi-pxa2xx-dma.c
+++ b/drivers/spi/spi-pxa2xx-dma.c
@@ -23,7 +23,7 @@
static void pxa2xx_spi_dma_transfer_complete(struct driver_data *drv_data,
bool error)
{
- struct spi_message *msg = drv_data->master->cur_msg;
+ struct spi_message *msg = drv_data->controller->cur_msg;
/*
* It is possible that one CPU is handling ROR interrupt and other
@@ -59,7 +59,7 @@
msg->status = -EIO;
}
- spi_finalize_current_transfer(drv_data->master);
+ spi_finalize_current_transfer(drv_data->controller);
}
}
@@ -74,7 +74,7 @@
struct spi_transfer *xfer)
{
struct chip_data *chip =
- spi_get_ctldata(drv_data->master->cur_msg->spi);
+ spi_get_ctldata(drv_data->controller->cur_msg->spi);
enum dma_slave_buswidth width;
struct dma_slave_config cfg;
struct dma_chan *chan;
@@ -102,14 +102,14 @@
cfg.dst_maxburst = chip->dma_burst_size;
sgt = &xfer->tx_sg;
- chan = drv_data->master->dma_tx;
+ chan = drv_data->controller->dma_tx;
} else {
cfg.src_addr = drv_data->ssdr_physical;
cfg.src_addr_width = width;
cfg.src_maxburst = chip->dma_burst_size;
sgt = &xfer->rx_sg;
- chan = drv_data->master->dma_rx;
+ chan = drv_data->controller->dma_rx;
}
ret = dmaengine_slave_config(chan, &cfg);
@@ -130,8 +130,8 @@
if (status & SSSR_ROR) {
dev_err(&drv_data->pdev->dev, "FIFO overrun\n");
- dmaengine_terminate_async(drv_data->master->dma_rx);
- dmaengine_terminate_async(drv_data->master->dma_tx);
+ dmaengine_terminate_async(drv_data->controller->dma_rx);
+ dmaengine_terminate_async(drv_data->controller->dma_tx);
pxa2xx_spi_dma_transfer_complete(drv_data, true);
return IRQ_HANDLED;
@@ -171,15 +171,15 @@
return 0;
err_rx:
- dmaengine_terminate_async(drv_data->master->dma_tx);
+ dmaengine_terminate_async(drv_data->controller->dma_tx);
err_tx:
return err;
}
void pxa2xx_spi_dma_start(struct driver_data *drv_data)
{
- dma_async_issue_pending(drv_data->master->dma_rx);
- dma_async_issue_pending(drv_data->master->dma_tx);
+ dma_async_issue_pending(drv_data->controller->dma_rx);
+ dma_async_issue_pending(drv_data->controller->dma_tx);
atomic_set(&drv_data->dma_running, 1);
}
@@ -187,30 +187,30 @@
void pxa2xx_spi_dma_stop(struct driver_data *drv_data)
{
atomic_set(&drv_data->dma_running, 0);
- dmaengine_terminate_sync(drv_data->master->dma_rx);
- dmaengine_terminate_sync(drv_data->master->dma_tx);
+ dmaengine_terminate_sync(drv_data->controller->dma_rx);
+ dmaengine_terminate_sync(drv_data->controller->dma_tx);
}
int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
{
- struct pxa2xx_spi_master *pdata = drv_data->master_info;
+ struct pxa2xx_spi_controller *pdata = drv_data->controller_info;
struct device *dev = &drv_data->pdev->dev;
- struct spi_controller *master = drv_data->master;
+ struct spi_controller *controller = drv_data->controller;
dma_cap_mask_t mask;
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
- master->dma_tx = dma_request_slave_channel_compat(mask,
+ controller->dma_tx = dma_request_slave_channel_compat(mask,
pdata->dma_filter, pdata->tx_param, dev, "tx");
- if (!master->dma_tx)
+ if (!controller->dma_tx)
return -ENODEV;
- master->dma_rx = dma_request_slave_channel_compat(mask,
+ controller->dma_rx = dma_request_slave_channel_compat(mask,
pdata->dma_filter, pdata->rx_param, dev, "rx");
- if (!master->dma_rx) {
- dma_release_channel(master->dma_tx);
- master->dma_tx = NULL;
+ if (!controller->dma_rx) {
+ dma_release_channel(controller->dma_tx);
+ controller->dma_tx = NULL;
return -ENODEV;
}
@@ -219,17 +219,17 @@
void pxa2xx_spi_dma_release(struct driver_data *drv_data)
{
- struct spi_controller *master = drv_data->master;
+ struct spi_controller *controller = drv_data->controller;
- if (master->dma_rx) {
- dmaengine_terminate_sync(master->dma_rx);
- dma_release_channel(master->dma_rx);
- master->dma_rx = NULL;
+ if (controller->dma_rx) {
+ dmaengine_terminate_sync(controller->dma_rx);
+ dma_release_channel(controller->dma_rx);
+ controller->dma_rx = NULL;
}
- if (master->dma_tx) {
- dmaengine_terminate_sync(master->dma_tx);
- dma_release_channel(master->dma_tx);
- master->dma_tx = NULL;
+ if (controller->dma_tx) {
+ dmaengine_terminate_sync(controller->dma_tx);
+ dma_release_channel(controller->dma_tx);
+ controller->dma_tx = NULL;
}
}
diff --git a/drivers/spi/spi-pxa2xx-pci.c b/drivers/spi/spi-pxa2xx-pci.c
index 869f188..1727fdf 100644
--- a/drivers/spi/spi-pxa2xx-pci.c
+++ b/drivers/spi/spi-pxa2xx-pci.c
@@ -197,7 +197,7 @@
struct platform_device_info pi;
int ret;
struct platform_device *pdev;
- struct pxa2xx_spi_master spi_pdata;
+ struct pxa2xx_spi_controller spi_pdata;
struct ssp_device *ssp;
struct pxa_spi_info *c;
char buf[40];
@@ -265,7 +265,7 @@
static void pxa2xx_spi_pci_remove(struct pci_dev *dev)
{
struct platform_device *pdev = pci_get_drvdata(dev);
- struct pxa2xx_spi_master *spi_pdata;
+ struct pxa2xx_spi_controller *spi_pdata;
spi_pdata = dev_get_platdata(&pdev->dev);
diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index d84b893..b6ddba8 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -328,7 +328,7 @@
__lpss_ssp_write_priv(drv_data, config->reg_cs_ctrl, value);
/* Enable multiblock DMA transfers */
- if (drv_data->master_info->enable_dma) {
+ if (drv_data->controller_info->enable_dma) {
__lpss_ssp_write_priv(drv_data, config->reg_ssp, 1);
if (config->reg_general >= 0) {
@@ -368,7 +368,7 @@
__lpss_ssp_write_priv(drv_data,
config->reg_cs_ctrl, value);
ndelay(1000000000 /
- (drv_data->master->max_speed_hz / 2));
+ (drv_data->controller->max_speed_hz / 2));
}
}
@@ -567,7 +567,7 @@
static void reset_sccr1(struct driver_data *drv_data)
{
struct chip_data *chip =
- spi_get_ctldata(drv_data->master->cur_msg->spi);
+ spi_get_ctldata(drv_data->controller->cur_msg->spi);
u32 sccr1_reg;
sccr1_reg = pxa2xx_spi_read(drv_data, SSCR1) & ~drv_data->int_cr1;
@@ -599,8 +599,8 @@
dev_err(&drv_data->pdev->dev, "%s\n", msg);
- drv_data->master->cur_msg->status = -EIO;
- spi_finalize_current_transfer(drv_data->master);
+ drv_data->controller->cur_msg->status = -EIO;
+ spi_finalize_current_transfer(drv_data->controller);
}
static void int_transfer_complete(struct driver_data *drv_data)
@@ -611,7 +611,7 @@
if (!pxa25x_ssp_comp(drv_data))
pxa2xx_spi_write(drv_data, SSTO, 0);
- spi_finalize_current_transfer(drv_data->master);
+ spi_finalize_current_transfer(drv_data->controller);
}
static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
@@ -747,7 +747,7 @@
pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg & ~drv_data->int_cr1);
pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg);
- if (!drv_data->master->cur_msg) {
+ if (!drv_data->controller->cur_msg) {
handle_bad_msg(drv_data);
/* Never fail */
return IRQ_HANDLED;
@@ -879,7 +879,7 @@
static unsigned int ssp_get_clk_div(struct driver_data *drv_data, int rate)
{
- unsigned long ssp_clk = drv_data->master->max_speed_hz;
+ unsigned long ssp_clk = drv_data->controller->max_speed_hz;
const struct ssp_device *ssp = drv_data->ssp;
rate = min_t(int, ssp_clk, rate);
@@ -894,7 +894,7 @@
int rate)
{
struct chip_data *chip =
- spi_get_ctldata(drv_data->master->cur_msg->spi);
+ spi_get_ctldata(drv_data->controller->cur_msg->spi);
unsigned int clk_div;
switch (drv_data->ssp_type) {
@@ -908,7 +908,7 @@
return clk_div << 8;
}
-static bool pxa2xx_spi_can_dma(struct spi_controller *master,
+static bool pxa2xx_spi_can_dma(struct spi_controller *controller,
struct spi_device *spi,
struct spi_transfer *xfer)
{
@@ -919,12 +919,12 @@
xfer->len >= chip->dma_burst_size;
}
-static int pxa2xx_spi_transfer_one(struct spi_controller *master,
+static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
struct spi_device *spi,
struct spi_transfer *transfer)
{
- struct driver_data *drv_data = spi_controller_get_devdata(master);
- struct spi_message *message = master->cur_msg;
+ struct driver_data *drv_data = spi_controller_get_devdata(controller);
+ struct spi_message *message = controller->cur_msg;
struct chip_data *chip = spi_get_ctldata(message->spi);
u32 dma_thresh = chip->dma_threshold;
u32 dma_burst = chip->dma_burst_size;
@@ -1006,9 +1006,9 @@
"DMA burst size reduced to match bits_per_word\n");
}
- dma_mapped = master->can_dma &&
- master->can_dma(master, message->spi, transfer) &&
- master->cur_msg_mapped;
+ dma_mapped = controller->can_dma &&
+ controller->can_dma(controller, message->spi, transfer) &&
+ controller->cur_msg_mapped;
if (dma_mapped) {
/* Ensure we have the correct interrupt handler */
@@ -1036,12 +1036,12 @@
cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
if (!pxa25x_ssp_comp(drv_data))
dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
- master->max_speed_hz
+ controller->max_speed_hz
/ (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
dma_mapped ? "DMA" : "PIO");
else
dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
- master->max_speed_hz / 2
+ controller->max_speed_hz / 2
/ (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
dma_mapped ? "DMA" : "PIO");
@@ -1092,7 +1092,7 @@
}
}
- if (spi_controller_is_slave(master)) {
+ if (spi_controller_is_slave(controller)) {
while (drv_data->write(drv_data))
;
if (drv_data->gpiod_ready) {
@@ -1111,9 +1111,9 @@
return 1;
}
-static int pxa2xx_spi_slave_abort(struct spi_master *master)
+static int pxa2xx_spi_slave_abort(struct spi_controller *controller)
{
- struct driver_data *drv_data = spi_controller_get_devdata(master);
+ struct driver_data *drv_data = spi_controller_get_devdata(controller);
/* Stop and reset SSP */
write_SSSR_CS(drv_data, drv_data->clear_sr);
@@ -1126,16 +1126,16 @@
dev_dbg(&drv_data->pdev->dev, "transfer aborted\n");
- drv_data->master->cur_msg->status = -EINTR;
- spi_finalize_current_transfer(drv_data->master);
+ drv_data->controller->cur_msg->status = -EINTR;
+ spi_finalize_current_transfer(drv_data->controller);
return 0;
}
-static void pxa2xx_spi_handle_err(struct spi_controller *master,
+static void pxa2xx_spi_handle_err(struct spi_controller *controller,
struct spi_message *msg)
{
- struct driver_data *drv_data = spi_controller_get_devdata(master);
+ struct driver_data *drv_data = spi_controller_get_devdata(controller);
/* Disable the SSP */
pxa2xx_spi_write(drv_data, SSCR0,
@@ -1159,9 +1159,9 @@
pxa2xx_spi_dma_stop(drv_data);
}
-static int pxa2xx_spi_unprepare_transfer(struct spi_controller *master)
+static int pxa2xx_spi_unprepare_transfer(struct spi_controller *controller)
{
- struct driver_data *drv_data = spi_controller_get_devdata(master);
+ struct driver_data *drv_data = spi_controller_get_devdata(controller);
/* Disable the SSP now */
pxa2xx_spi_write(drv_data, SSCR0,
@@ -1260,7 +1260,7 @@
break;
default:
tx_hi_thres = 0;
- if (spi_controller_is_slave(drv_data->master)) {
+ if (spi_controller_is_slave(drv_data->controller)) {
tx_thres = 1;
rx_thres = 2;
} else {
@@ -1287,7 +1287,7 @@
chip->frm = spi->chip_select;
}
- chip->enable_dma = drv_data->master_info->enable_dma;
+ chip->enable_dma = drv_data->controller_info->enable_dma;
chip->timeout = TIMOUT_DFLT;
}
@@ -1310,7 +1310,7 @@
if (chip_info->enable_loopback)
chip->cr1 = SSCR1_LBM;
}
- if (spi_controller_is_slave(drv_data->master)) {
+ if (spi_controller_is_slave(drv_data->controller)) {
chip->cr1 |= SSCR1_SCFR;
chip->cr1 |= SSCR1_SCLKDIR;
chip->cr1 |= SSCR1_SFRMDIR;
@@ -1497,10 +1497,10 @@
#endif /* CONFIG_PCI */
-static struct pxa2xx_spi_master *
+static struct pxa2xx_spi_controller *
pxa2xx_spi_init_pdata(struct platform_device *pdev)
{
- struct pxa2xx_spi_master *pdata;
+ struct pxa2xx_spi_controller *pdata;
struct acpi_device *adev;
struct ssp_device *ssp;
struct resource *res;
@@ -1568,10 +1568,10 @@
return pdata;
}
-static int pxa2xx_spi_fw_translate_cs(struct spi_controller *master,
+static int pxa2xx_spi_fw_translate_cs(struct spi_controller *controller,
unsigned int cs)
{
- struct driver_data *drv_data = spi_controller_get_devdata(master);
+ struct driver_data *drv_data = spi_controller_get_devdata(controller);
if (has_acpi_companion(&drv_data->pdev->dev)) {
switch (drv_data->ssp_type) {
@@ -1595,8 +1595,8 @@
static int pxa2xx_spi_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
- struct pxa2xx_spi_master *platform_info;
- struct spi_controller *master;
+ struct pxa2xx_spi_controller *platform_info;
+ struct spi_controller *controller;
struct driver_data *drv_data;
struct ssp_device *ssp;
const struct lpss_config *config;
@@ -1622,37 +1622,37 @@
}
if (platform_info->is_slave)
- master = spi_alloc_slave(dev, sizeof(struct driver_data));
+ controller = spi_alloc_slave(dev, sizeof(struct driver_data));
else
- master = spi_alloc_master(dev, sizeof(struct driver_data));
+ controller = spi_alloc_master(dev, sizeof(struct driver_data));
- if (!master) {
- dev_err(&pdev->dev, "cannot alloc spi_master\n");
+ if (!controller) {
+ dev_err(&pdev->dev, "cannot alloc spi_controller\n");
pxa_ssp_free(ssp);
return -ENOMEM;
}
- drv_data = spi_controller_get_devdata(master);
- drv_data->master = master;
- drv_data->master_info = platform_info;
+ drv_data = spi_controller_get_devdata(controller);
+ drv_data->controller = controller;
+ drv_data->controller_info = platform_info;
drv_data->pdev = pdev;
drv_data->ssp = ssp;
- master->dev.of_node = pdev->dev.of_node;
+ controller->dev.of_node = pdev->dev.of_node;
/* the spi->mode bits understood by this driver: */
- master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
+ controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
- master->bus_num = ssp->port_id;
- master->dma_alignment = DMA_ALIGNMENT;
- master->cleanup = cleanup;
- master->setup = setup;
- master->set_cs = pxa2xx_spi_set_cs;
- master->transfer_one = pxa2xx_spi_transfer_one;
- master->slave_abort = pxa2xx_spi_slave_abort;
- master->handle_err = pxa2xx_spi_handle_err;
- master->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer;
- master->fw_translate_cs = pxa2xx_spi_fw_translate_cs;
- master->auto_runtime_pm = true;
- master->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX;
+ controller->bus_num = ssp->port_id;
+ controller->dma_alignment = DMA_ALIGNMENT;
+ controller->cleanup = cleanup;
+ controller->setup = setup;
+ controller->set_cs = pxa2xx_spi_set_cs;
+ controller->transfer_one = pxa2xx_spi_transfer_one;
+ controller->slave_abort = pxa2xx_spi_slave_abort;
+ controller->handle_err = pxa2xx_spi_handle_err;
+ controller->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer;
+ controller->fw_translate_cs = pxa2xx_spi_fw_translate_cs;
+ controller->auto_runtime_pm = true;
+ controller->flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX;
drv_data->ssp_type = ssp->type;
@@ -1661,10 +1661,10 @@
if (pxa25x_ssp_comp(drv_data)) {
switch (drv_data->ssp_type) {
case QUARK_X1000_SSP:
- master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
+ controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
break;
default:
- master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
+ controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
break;
}
@@ -1673,7 +1673,7 @@
drv_data->clear_sr = SSSR_ROR;
drv_data->mask_sr = SSSR_RFS | SSSR_TFS | SSSR_ROR;
} else {
- master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
+ controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
drv_data->int_cr1 = SSCR1_TIE | SSCR1_RIE | SSCR1_TINTE;
drv_data->dma_cr1 = DEFAULT_DMA_CR1;
drv_data->clear_sr = SSSR_ROR | SSSR_TINT;
@@ -1685,7 +1685,7 @@
drv_data);
if (status < 0) {
dev_err(&pdev->dev, "cannot get IRQ %d\n", ssp->irq);
- goto out_error_master_alloc;
+ goto out_error_controller_alloc;
}
/* Setup DMA if requested */
@@ -1695,7 +1695,8 @@
dev_dbg(dev, "no DMA channels available, using PIO\n");
platform_info->enable_dma = false;
} else {
- master->can_dma = pxa2xx_spi_can_dma;
+ controller->can_dma = pxa2xx_spi_can_dma;
+ controller->max_dma_len = MAX_DMA_LEN;
}
}
@@ -1704,7 +1705,7 @@
if (status)
goto out_error_dma_irq_alloc;
- master->max_speed_hz = clk_get_rate(ssp->clk);
+ controller->max_speed_hz = clk_get_rate(ssp->clk);
/* Load default SSP configuration */
pxa2xx_spi_write(drv_data, SSCR0, 0);
@@ -1727,7 +1728,7 @@
break;
default:
- if (spi_controller_is_slave(master)) {
+ if (spi_controller_is_slave(controller)) {
tmp = SSCR1_SCFR |
SSCR1_SCLKDIR |
SSCR1_SFRMDIR |
@@ -1740,7 +1741,7 @@
}
pxa2xx_spi_write(drv_data, SSCR1, tmp);
tmp = SSCR0_Motorola | SSCR0_DataSize(8);
- if (!spi_controller_is_slave(master))
+ if (!spi_controller_is_slave(controller))
tmp |= SSCR0_SCR(2);
pxa2xx_spi_write(drv_data, SSCR0, tmp);
break;
@@ -1765,24 +1766,24 @@
platform_info->num_chipselect = config->cs_num;
}
}
- master->num_chipselect = platform_info->num_chipselect;
+ controller->num_chipselect = platform_info->num_chipselect;
count = gpiod_count(&pdev->dev, "cs");
if (count > 0) {
int i;
- master->num_chipselect = max_t(int, count,
- master->num_chipselect);
+ controller->num_chipselect = max_t(int, count,
+ controller->num_chipselect);
drv_data->cs_gpiods = devm_kcalloc(&pdev->dev,
- master->num_chipselect, sizeof(struct gpio_desc *),
+ controller->num_chipselect, sizeof(struct gpio_desc *),
GFP_KERNEL);
if (!drv_data->cs_gpiods) {
status = -ENOMEM;
goto out_error_clock_enabled;
}
- for (i = 0; i < master->num_chipselect; i++) {
+ for (i = 0; i < controller->num_chipselect; i++) {
struct gpio_desc *gpiod;
gpiod = devm_gpiod_get_index(dev, "cs", i, GPIOD_ASIS);
@@ -1815,9 +1816,9 @@
/* Register with the SPI framework */
platform_set_drvdata(pdev, drv_data);
- status = devm_spi_register_controller(&pdev->dev, master);
+ status = devm_spi_register_controller(&pdev->dev, controller);
if (status != 0) {
- dev_err(&pdev->dev, "problem registering spi master\n");
+ dev_err(&pdev->dev, "problem registering spi controller\n");
goto out_error_clock_enabled;
}
@@ -1832,8 +1833,8 @@
pxa2xx_spi_dma_release(drv_data);
free_irq(ssp->irq, drv_data);
-out_error_master_alloc:
- spi_controller_put(master);
+out_error_controller_alloc:
+ spi_controller_put(controller);
pxa_ssp_free(ssp);
return status;
}
@@ -1854,7 +1855,7 @@
clk_disable_unprepare(ssp->clk);
/* Release DMA */
- if (drv_data->master_info->enable_dma)
+ if (drv_data->controller_info->enable_dma)
pxa2xx_spi_dma_release(drv_data);
pm_runtime_put_noidle(&pdev->dev);
@@ -1876,7 +1877,7 @@
struct ssp_device *ssp = drv_data->ssp;
int status;
- status = spi_controller_suspend(drv_data->master);
+ status = spi_controller_suspend(drv_data->controller);
if (status != 0)
return status;
pxa2xx_spi_write(drv_data, SSCR0, 0);
@@ -1901,7 +1902,7 @@
}
/* Start the queue running */
- return spi_controller_resume(drv_data->master);
+ return spi_controller_resume(drv_data->controller);
}
#endif
diff --git a/drivers/spi/spi-pxa2xx.h b/drivers/spi/spi-pxa2xx.h
index 4e324da..aba777b 100644
--- a/drivers/spi/spi-pxa2xx.h
+++ b/drivers/spi/spi-pxa2xx.h
@@ -31,10 +31,10 @@
/* SPI framework hookup */
enum pxa_ssp_type ssp_type;
- struct spi_controller *master;
+ struct spi_controller *controller;
/* PXA hookup */
- struct pxa2xx_spi_master *master_info;
+ struct pxa2xx_spi_controller *controller_info;
/* SSP register addresses */
void __iomem *ioaddr;
diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c
index a4ef641..556870d 100644
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -180,7 +180,7 @@
struct rspi_data {
void __iomem *addr;
u32 max_speed_hz;
- struct spi_master *master;
+ struct spi_controller *ctlr;
wait_queue_head_t wait;
struct clk *clk;
u16 spcmd;
@@ -237,8 +237,8 @@
/* optional functions */
struct spi_ops {
int (*set_config_register)(struct rspi_data *rspi, int access_size);
- int (*transfer_one)(struct spi_master *master, struct spi_device *spi,
- struct spi_transfer *xfer);
+ int (*transfer_one)(struct spi_controller *ctlr,
+ struct spi_device *spi, struct spi_transfer *xfer);
u16 mode_bits;
u16 flags;
u16 fifo_size;
@@ -466,7 +466,7 @@
{
int error = rspi_wait_for_tx_empty(rspi);
if (error < 0) {
- dev_err(&rspi->master->dev, "transmit timeout\n");
+ dev_err(&rspi->ctlr->dev, "transmit timeout\n");
return error;
}
rspi_write_data(rspi, data);
@@ -480,7 +480,7 @@
error = rspi_wait_for_rx_full(rspi);
if (error < 0) {
- dev_err(&rspi->master->dev, "receive timeout\n");
+ dev_err(&rspi->ctlr->dev, "receive timeout\n");
return error;
}
data = rspi_read_data(rspi);
@@ -526,8 +526,8 @@
/* First prepare and submit the DMA request(s), as this may fail */
if (rx) {
- desc_rx = dmaengine_prep_slave_sg(rspi->master->dma_rx,
- rx->sgl, rx->nents, DMA_DEV_TO_MEM,
+ desc_rx = dmaengine_prep_slave_sg(rspi->ctlr->dma_rx, rx->sgl,
+ rx->nents, DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc_rx) {
ret = -EAGAIN;
@@ -546,8 +546,8 @@
}
if (tx) {
- desc_tx = dmaengine_prep_slave_sg(rspi->master->dma_tx,
- tx->sgl, tx->nents, DMA_MEM_TO_DEV,
+ desc_tx = dmaengine_prep_slave_sg(rspi->ctlr->dma_tx, tx->sgl,
+ tx->nents, DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc_tx) {
ret = -EAGAIN;
@@ -584,9 +584,9 @@
/* Now start DMA */
if (rx)
- dma_async_issue_pending(rspi->master->dma_rx);
+ dma_async_issue_pending(rspi->ctlr->dma_rx);
if (tx)
- dma_async_issue_pending(rspi->master->dma_tx);
+ dma_async_issue_pending(rspi->ctlr->dma_tx);
ret = wait_event_interruptible_timeout(rspi->wait,
rspi->dma_callbacked, HZ);
@@ -594,13 +594,13 @@
ret = 0;
} else {
if (!ret) {
- dev_err(&rspi->master->dev, "DMA timeout\n");
+ dev_err(&rspi->ctlr->dev, "DMA timeout\n");
ret = -ETIMEDOUT;
}
if (tx)
- dmaengine_terminate_all(rspi->master->dma_tx);
+ dmaengine_terminate_all(rspi->ctlr->dma_tx);
if (rx)
- dmaengine_terminate_all(rspi->master->dma_rx);
+ dmaengine_terminate_all(rspi->ctlr->dma_rx);
}
rspi_disable_irq(rspi, irq_mask);
@@ -614,12 +614,12 @@
no_dma_tx:
if (rx)
- dmaengine_terminate_all(rspi->master->dma_rx);
+ dmaengine_terminate_all(rspi->ctlr->dma_rx);
no_dma_rx:
if (ret == -EAGAIN) {
pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
- dev_driver_string(&rspi->master->dev),
- dev_name(&rspi->master->dev));
+ dev_driver_string(&rspi->ctlr->dev),
+ dev_name(&rspi->ctlr->dev));
}
return ret;
}
@@ -660,10 +660,10 @@
return xfer->len > rspi->ops->fifo_size;
}
-static bool rspi_can_dma(struct spi_master *master, struct spi_device *spi,
+static bool rspi_can_dma(struct spi_controller *ctlr, struct spi_device *spi,
struct spi_transfer *xfer)
{
- struct rspi_data *rspi = spi_master_get_devdata(master);
+ struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
return __rspi_can_dma(rspi, xfer);
}
@@ -671,7 +671,7 @@
static int rspi_dma_check_then_transfer(struct rspi_data *rspi,
struct spi_transfer *xfer)
{
- if (!rspi->master->can_dma || !__rspi_can_dma(rspi, xfer))
+ if (!rspi->ctlr->can_dma || !__rspi_can_dma(rspi, xfer))
return -EAGAIN;
/* rx_buf can be NULL on RSPI on SH in TX-only Mode */
@@ -698,10 +698,10 @@
return 0;
}
-static int rspi_transfer_one(struct spi_master *master, struct spi_device *spi,
- struct spi_transfer *xfer)
+static int rspi_transfer_one(struct spi_controller *ctlr,
+ struct spi_device *spi, struct spi_transfer *xfer)
{
- struct rspi_data *rspi = spi_master_get_devdata(master);
+ struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
u8 spcr;
spcr = rspi_read8(rspi, RSPI_SPCR);
@@ -716,11 +716,11 @@
return rspi_common_transfer(rspi, xfer);
}
-static int rspi_rz_transfer_one(struct spi_master *master,
+static int rspi_rz_transfer_one(struct spi_controller *ctlr,
struct spi_device *spi,
struct spi_transfer *xfer)
{
- struct rspi_data *rspi = spi_master_get_devdata(master);
+ struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
rspi_rz_receive_init(rspi);
@@ -739,7 +739,7 @@
if (n == QSPI_BUFFER_SIZE) {
ret = rspi_wait_for_tx_empty(rspi);
if (ret < 0) {
- dev_err(&rspi->master->dev, "transmit timeout\n");
+ dev_err(&rspi->ctlr->dev, "transmit timeout\n");
return ret;
}
for (i = 0; i < n; i++)
@@ -747,7 +747,7 @@
ret = rspi_wait_for_rx_full(rspi);
if (ret < 0) {
- dev_err(&rspi->master->dev, "receive timeout\n");
+ dev_err(&rspi->ctlr->dev, "receive timeout\n");
return ret;
}
for (i = 0; i < n; i++)
@@ -785,7 +785,7 @@
unsigned int i, len;
int ret;
- if (rspi->master->can_dma && __rspi_can_dma(rspi, xfer)) {
+ if (rspi->ctlr->can_dma && __rspi_can_dma(rspi, xfer)) {
ret = rspi_dma_transfer(rspi, &xfer->tx_sg, NULL);
if (ret != -EAGAIN)
return ret;
@@ -796,7 +796,7 @@
if (len == QSPI_BUFFER_SIZE) {
ret = rspi_wait_for_tx_empty(rspi);
if (ret < 0) {
- dev_err(&rspi->master->dev, "transmit timeout\n");
+ dev_err(&rspi->ctlr->dev, "transmit timeout\n");
return ret;
}
for (i = 0; i < len; i++)
@@ -822,7 +822,7 @@
unsigned int i, len;
int ret;
- if (rspi->master->can_dma && __rspi_can_dma(rspi, xfer)) {
+ if (rspi->ctlr->can_dma && __rspi_can_dma(rspi, xfer)) {
int ret = rspi_dma_transfer(rspi, NULL, &xfer->rx_sg);
if (ret != -EAGAIN)
return ret;
@@ -833,7 +833,7 @@
if (len == QSPI_BUFFER_SIZE) {
ret = rspi_wait_for_rx_full(rspi);
if (ret < 0) {
- dev_err(&rspi->master->dev, "receive timeout\n");
+ dev_err(&rspi->ctlr->dev, "receive timeout\n");
return ret;
}
for (i = 0; i < len; i++)
@@ -849,10 +849,10 @@
return 0;
}
-static int qspi_transfer_one(struct spi_master *master, struct spi_device *spi,
- struct spi_transfer *xfer)
+static int qspi_transfer_one(struct spi_controller *ctlr,
+ struct spi_device *spi, struct spi_transfer *xfer)
{
- struct rspi_data *rspi = spi_master_get_devdata(master);
+ struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
if (spi->mode & SPI_LOOP) {
return qspi_transfer_out_in(rspi, xfer);
@@ -870,7 +870,7 @@
static int rspi_setup(struct spi_device *spi)
{
- struct rspi_data *rspi = spi_master_get_devdata(spi->master);
+ struct rspi_data *rspi = spi_controller_get_devdata(spi->controller);
rspi->max_speed_hz = spi->max_speed_hz;
@@ -955,10 +955,10 @@
return 0;
}
-static int rspi_prepare_message(struct spi_master *master,
+static int rspi_prepare_message(struct spi_controller *ctlr,
struct spi_message *msg)
{
- struct rspi_data *rspi = spi_master_get_devdata(master);
+ struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
int ret;
if (msg->spi->mode &
@@ -974,10 +974,10 @@
return 0;
}
-static int rspi_unprepare_message(struct spi_master *master,
+static int rspi_unprepare_message(struct spi_controller *ctlr,
struct spi_message *msg)
{
- struct rspi_data *rspi = spi_master_get_devdata(master);
+ struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
/* Disable SPI function */
rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~SPCR_SPE, RSPI_SPCR);
@@ -1081,7 +1081,7 @@
return chan;
}
-static int rspi_request_dma(struct device *dev, struct spi_master *master,
+static int rspi_request_dma(struct device *dev, struct spi_controller *ctlr,
const struct resource *res)
{
const struct rspi_plat_data *rspi_pd = dev_get_platdata(dev);
@@ -1099,37 +1099,37 @@
return 0;
}
- master->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
- res->start + RSPI_SPDR);
- if (!master->dma_tx)
+ ctlr->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id,
+ res->start + RSPI_SPDR);
+ if (!ctlr->dma_tx)
return -ENODEV;
- master->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
- res->start + RSPI_SPDR);
- if (!master->dma_rx) {
- dma_release_channel(master->dma_tx);
- master->dma_tx = NULL;
+ ctlr->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id,
+ res->start + RSPI_SPDR);
+ if (!ctlr->dma_rx) {
+ dma_release_channel(ctlr->dma_tx);
+ ctlr->dma_tx = NULL;
return -ENODEV;
}
- master->can_dma = rspi_can_dma;
+ ctlr->can_dma = rspi_can_dma;
dev_info(dev, "DMA available");
return 0;
}
-static void rspi_release_dma(struct spi_master *master)
+static void rspi_release_dma(struct spi_controller *ctlr)
{
- if (master->dma_tx)
- dma_release_channel(master->dma_tx);
- if (master->dma_rx)
- dma_release_channel(master->dma_rx);
+ if (ctlr->dma_tx)
+ dma_release_channel(ctlr->dma_tx);
+ if (ctlr->dma_rx)
+ dma_release_channel(ctlr->dma_rx);
}
static int rspi_remove(struct platform_device *pdev)
{
struct rspi_data *rspi = platform_get_drvdata(pdev);
- rspi_release_dma(rspi->master);
+ rspi_release_dma(rspi->ctlr);
pm_runtime_disable(&pdev->dev);
return 0;
@@ -1139,7 +1139,7 @@
.set_config_register = rspi_set_config_register,
.transfer_one = rspi_transfer_one,
.mode_bits = SPI_CPHA | SPI_CPOL | SPI_LOOP,
- .flags = SPI_MASTER_MUST_TX,
+ .flags = SPI_CONTROLLER_MUST_TX,
.fifo_size = 8,
};
@@ -1147,7 +1147,7 @@
.set_config_register = rspi_rz_set_config_register,
.transfer_one = rspi_rz_transfer_one,
.mode_bits = SPI_CPHA | SPI_CPOL | SPI_LOOP,
- .flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX,
+ .flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX,
.fifo_size = 8, /* 8 for TX, 32 for RX */
};
@@ -1157,7 +1157,7 @@
.mode_bits = SPI_CPHA | SPI_CPOL | SPI_LOOP |
SPI_TX_DUAL | SPI_TX_QUAD |
SPI_RX_DUAL | SPI_RX_QUAD,
- .flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX,
+ .flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX,
.fifo_size = 32,
};
@@ -1174,7 +1174,7 @@
MODULE_DEVICE_TABLE(of, rspi_of_match);
-static int rspi_parse_dt(struct device *dev, struct spi_master *master)
+static int rspi_parse_dt(struct device *dev, struct spi_controller *ctlr)
{
u32 num_cs;
int error;
@@ -1186,12 +1186,12 @@
return error;
}
- master->num_chipselect = num_cs;
+ ctlr->num_chipselect = num_cs;
return 0;
}
#else
#define rspi_of_match NULL
-static inline int rspi_parse_dt(struct device *dev, struct spi_master *master)
+static inline int rspi_parse_dt(struct device *dev, struct spi_controller *ctlr)
{
return -EINVAL;
}
@@ -1212,28 +1212,28 @@
static int rspi_probe(struct platform_device *pdev)
{
struct resource *res;
- struct spi_master *master;
+ struct spi_controller *ctlr;
struct rspi_data *rspi;
int ret;
const struct rspi_plat_data *rspi_pd;
const struct spi_ops *ops;
- master = spi_alloc_master(&pdev->dev, sizeof(struct rspi_data));
- if (master == NULL)
+ ctlr = spi_alloc_master(&pdev->dev, sizeof(struct rspi_data));
+ if (ctlr == NULL)
return -ENOMEM;
ops = of_device_get_match_data(&pdev->dev);
if (ops) {
- ret = rspi_parse_dt(&pdev->dev, master);
+ ret = rspi_parse_dt(&pdev->dev, ctlr);
if (ret)
goto error1;
} else {
ops = (struct spi_ops *)pdev->id_entry->driver_data;
rspi_pd = dev_get_platdata(&pdev->dev);
if (rspi_pd && rspi_pd->num_chipselect)
- master->num_chipselect = rspi_pd->num_chipselect;
+ ctlr->num_chipselect = rspi_pd->num_chipselect;
else
- master->num_chipselect = 2; /* default */
+ ctlr->num_chipselect = 2; /* default */
}
/* ops parameter check */
@@ -1243,10 +1243,10 @@
goto error1;
}
- rspi = spi_master_get_devdata(master);
+ rspi = spi_controller_get_devdata(ctlr);
platform_set_drvdata(pdev, rspi);
rspi->ops = ops;
- rspi->master = master;
+ rspi->ctlr = ctlr;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
rspi->addr = devm_ioremap_resource(&pdev->dev, res);
@@ -1266,15 +1266,15 @@
init_waitqueue_head(&rspi->wait);
- master->bus_num = pdev->id;
- master->setup = rspi_setup;
- master->auto_runtime_pm = true;
- master->transfer_one = ops->transfer_one;
- master->prepare_message = rspi_prepare_message;
- master->unprepare_message = rspi_unprepare_message;
- master->mode_bits = ops->mode_bits;
- master->flags = ops->flags;
- master->dev.of_node = pdev->dev.of_node;
+ ctlr->bus_num = pdev->id;
+ ctlr->setup = rspi_setup;
+ ctlr->auto_runtime_pm = true;
+ ctlr->transfer_one = ops->transfer_one;
+ ctlr->prepare_message = rspi_prepare_message;
+ ctlr->unprepare_message = rspi_unprepare_message;
+ ctlr->mode_bits = ops->mode_bits;
+ ctlr->flags = ops->flags;
+ ctlr->dev.of_node = pdev->dev.of_node;
ret = platform_get_irq_byname(pdev, "rx");
if (ret < 0) {
@@ -1311,13 +1311,13 @@
goto error2;
}
- ret = rspi_request_dma(&pdev->dev, master, res);
+ ret = rspi_request_dma(&pdev->dev, ctlr, res);
if (ret < 0)
dev_warn(&pdev->dev, "DMA not available, using PIO\n");
- ret = devm_spi_register_master(&pdev->dev, master);
+ ret = devm_spi_register_controller(&pdev->dev, ctlr);
if (ret < 0) {
- dev_err(&pdev->dev, "spi_register_master error.\n");
+ dev_err(&pdev->dev, "devm_spi_register_controller error.\n");
goto error3;
}
@@ -1326,11 +1326,11 @@
return 0;
error3:
- rspi_release_dma(master);
+ rspi_release_dma(ctlr);
error2:
pm_runtime_disable(&pdev->dev);
error1:
- spi_master_put(master);
+ spi_controller_put(ctlr);
return ret;
}
@@ -1349,14 +1349,14 @@
{
struct rspi_data *rspi = dev_get_drvdata(dev);
- return spi_master_suspend(rspi->master);
+ return spi_controller_suspend(rspi->ctlr);
}
static int rspi_resume(struct device *dev)
{
struct rspi_data *rspi = dev_get_drvdata(dev);
- return spi_master_resume(rspi->master);
+ return spi_controller_resume(rspi->ctlr);
}
static SIMPLE_DEV_PM_OPS(rspi_pm_ops, rspi_suspend, rspi_resume);
diff --git a/drivers/spi/spi-sh-hspi.c b/drivers/spi/spi-sh-hspi.c
index dc0926e..7f73f91 100644
--- a/drivers/spi/spi-sh-hspi.c
+++ b/drivers/spi/spi-sh-hspi.c
@@ -35,7 +35,7 @@
struct hspi_priv {
void __iomem *addr;
- struct spi_master *master;
+ struct spi_controller *ctlr;
struct device *dev;
struct clk *clk;
};
@@ -140,10 +140,10 @@
hspi_write(hspi, SPSCR, 0x21); /* master mode / CS control */
}
-static int hspi_transfer_one_message(struct spi_master *master,
+static int hspi_transfer_one_message(struct spi_controller *ctlr,
struct spi_message *msg)
{
- struct hspi_priv *hspi = spi_master_get_devdata(master);
+ struct hspi_priv *hspi = spi_controller_get_devdata(ctlr);
struct spi_transfer *t;
u32 tx;
u32 rx;
@@ -205,7 +205,7 @@
ndelay(nsecs);
hspi_hw_cs_disable(hspi);
}
- spi_finalize_current_message(master);
+ spi_finalize_current_message(ctlr);
return ret;
}
@@ -213,7 +213,7 @@
static int hspi_probe(struct platform_device *pdev)
{
struct resource *res;
- struct spi_master *master;
+ struct spi_controller *ctlr;
struct hspi_priv *hspi;
struct clk *clk;
int ret;
@@ -225,11 +225,9 @@
return -EINVAL;
}
- master = spi_alloc_master(&pdev->dev, sizeof(*hspi));
- if (!master) {
- dev_err(&pdev->dev, "spi_alloc_master error.\n");
+ ctlr = spi_alloc_master(&pdev->dev, sizeof(*hspi));
+ if (!ctlr)
return -ENOMEM;
- }
clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(clk)) {
@@ -238,33 +236,32 @@
goto error0;
}
- hspi = spi_master_get_devdata(master);
+ hspi = spi_controller_get_devdata(ctlr);
platform_set_drvdata(pdev, hspi);
/* init hspi */
- hspi->master = master;
+ hspi->ctlr = ctlr;
hspi->dev = &pdev->dev;
hspi->clk = clk;
hspi->addr = devm_ioremap(hspi->dev,
res->start, resource_size(res));
if (!hspi->addr) {
- dev_err(&pdev->dev, "ioremap error.\n");
ret = -ENOMEM;
goto error1;
}
pm_runtime_enable(&pdev->dev);
- master->bus_num = pdev->id;
- master->mode_bits = SPI_CPOL | SPI_CPHA;
- master->dev.of_node = pdev->dev.of_node;
- master->auto_runtime_pm = true;
- master->transfer_one_message = hspi_transfer_one_message;
- master->bits_per_word_mask = SPI_BPW_MASK(8);
+ ctlr->bus_num = pdev->id;
+ ctlr->mode_bits = SPI_CPOL | SPI_CPHA;
+ ctlr->dev.of_node = pdev->dev.of_node;
+ ctlr->auto_runtime_pm = true;
+ ctlr->transfer_one_message = hspi_transfer_one_message;
+ ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
- ret = devm_spi_register_master(&pdev->dev, master);
+ ret = devm_spi_register_controller(&pdev->dev, ctlr);
if (ret < 0) {
- dev_err(&pdev->dev, "spi_register_master error.\n");
+ dev_err(&pdev->dev, "devm_spi_register_controller error.\n");
goto error2;
}
@@ -275,7 +272,7 @@
error1:
clk_put(clk);
error0:
- spi_master_put(master);
+ spi_controller_put(ctlr);
return ret;
}
diff --git a/drivers/spi/spi-sh-msiof.c b/drivers/spi/spi-sh-msiof.c
index d14b407..e2eb466 100644
--- a/drivers/spi/spi-sh-msiof.c
+++ b/drivers/spi/spi-sh-msiof.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * SuperH MSIOF SPI Master Interface
+ * SuperH MSIOF SPI Controller Interface
*
* Copyright (c) 2009 Magnus Damm
* Copyright (C) 2014 Renesas Electronics Corporation
@@ -32,14 +32,15 @@
#include <asm/unaligned.h>
struct sh_msiof_chipdata {
+ u32 bits_per_word_mask;
u16 tx_fifo_size;
u16 rx_fifo_size;
- u16 master_flags;
+ u16 ctlr_flags;
u16 min_div_pow;
};
struct sh_msiof_spi_priv {
- struct spi_master *master;
+ struct spi_controller *ctlr;
void __iomem *mapbase;
struct clk *clk;
struct platform_device *pdev;
@@ -287,7 +288,7 @@
scr = sh_msiof_spi_div_array[div_pow] | SCR_BRPS(brps);
sh_msiof_write(p, TSCR, scr);
- if (!(p->master->flags & SPI_MASTER_MUST_TX))
+ if (!(p->ctlr->flags & SPI_CONTROLLER_MUST_TX))
sh_msiof_write(p, RSCR, scr);
}
@@ -351,14 +352,14 @@
tmp |= !cs_high << MDR1_SYNCAC_SHIFT;
tmp |= lsb_first << MDR1_BITLSB_SHIFT;
tmp |= sh_msiof_spi_get_dtdl_and_syncdl(p);
- if (spi_controller_is_slave(p->master)) {
+ if (spi_controller_is_slave(p->ctlr)) {
sh_msiof_write(p, TMDR1, tmp | TMDR1_PCON);
} else {
sh_msiof_write(p, TMDR1,
tmp | MDR1_TRMD | TMDR1_PCON |
(ss < MAX_SS ? ss : 0) << TMDR1_SYNCCH_SHIFT);
}
- if (p->master->flags & SPI_MASTER_MUST_TX) {
+ if (p->ctlr->flags & SPI_CONTROLLER_MUST_TX) {
/* These bits are reserved if RX needs TX */
tmp &= ~0x0000ffff;
}
@@ -382,7 +383,7 @@
{
u32 dr2 = MDR2_BITLEN1(bits) | MDR2_WDLEN1(words);
- if (tx_buf || (p->master->flags & SPI_MASTER_MUST_TX))
+ if (tx_buf || (p->ctlr->flags & SPI_CONTROLLER_MUST_TX))
sh_msiof_write(p, TMDR2, dr2);
else
sh_msiof_write(p, TMDR2, dr2 | MDR2_GRPMASK1);
@@ -539,8 +540,9 @@
static int sh_msiof_spi_setup(struct spi_device *spi)
{
- struct device_node *np = spi->master->dev.of_node;
- struct sh_msiof_spi_priv *p = spi_master_get_devdata(spi->master);
+ struct device_node *np = spi->controller->dev.of_node;
+ struct sh_msiof_spi_priv *p =
+ spi_controller_get_devdata(spi->controller);
u32 clr, set, tmp;
if (!np) {
@@ -556,7 +558,7 @@
return 0;
}
- if (spi_controller_is_slave(p->master))
+ if (spi_controller_is_slave(p->ctlr))
return 0;
if (p->native_cs_inited &&
@@ -581,10 +583,10 @@
return 0;
}
-static int sh_msiof_prepare_message(struct spi_master *master,
+static int sh_msiof_prepare_message(struct spi_controller *ctlr,
struct spi_message *msg)
{
- struct sh_msiof_spi_priv *p = spi_master_get_devdata(master);
+ struct sh_msiof_spi_priv *p = spi_controller_get_devdata(ctlr);
const struct spi_device *spi = msg->spi;
u32 ss, cs_high;
@@ -605,7 +607,7 @@
static int sh_msiof_spi_start(struct sh_msiof_spi_priv *p, void *rx_buf)
{
- bool slave = spi_controller_is_slave(p->master);
+ bool slave = spi_controller_is_slave(p->ctlr);
int ret = 0;
/* setup clock and rx/tx signals */
@@ -625,7 +627,7 @@
static int sh_msiof_spi_stop(struct sh_msiof_spi_priv *p, void *rx_buf)
{
- bool slave = spi_controller_is_slave(p->master);
+ bool slave = spi_controller_is_slave(p->ctlr);
int ret = 0;
/* shut down frame, rx/tx and clock signals */
@@ -641,9 +643,9 @@
return ret;
}
-static int sh_msiof_slave_abort(struct spi_master *master)
+static int sh_msiof_slave_abort(struct spi_controller *ctlr)
{
- struct sh_msiof_spi_priv *p = spi_master_get_devdata(master);
+ struct sh_msiof_spi_priv *p = spi_controller_get_devdata(ctlr);
p->slave_aborted = true;
complete(&p->done);
@@ -654,7 +656,7 @@
static int sh_msiof_wait_for_completion(struct sh_msiof_spi_priv *p,
struct completion *x)
{
- if (spi_controller_is_slave(p->master)) {
+ if (spi_controller_is_slave(p->ctlr)) {
if (wait_for_completion_interruptible(x) ||
p->slave_aborted) {
dev_dbg(&p->pdev->dev, "interrupted\n");
@@ -754,7 +756,7 @@
/* First prepare and submit the DMA request(s), as this may fail */
if (rx) {
ier_bits |= IER_RDREQE | IER_RDMAE;
- desc_rx = dmaengine_prep_slave_single(p->master->dma_rx,
+ desc_rx = dmaengine_prep_slave_single(p->ctlr->dma_rx,
p->rx_dma_addr, len, DMA_DEV_TO_MEM,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc_rx)
@@ -769,9 +771,9 @@
if (tx) {
ier_bits |= IER_TDREQE | IER_TDMAE;
- dma_sync_single_for_device(p->master->dma_tx->device->dev,
+ dma_sync_single_for_device(p->ctlr->dma_tx->device->dev,
p->tx_dma_addr, len, DMA_TO_DEVICE);
- desc_tx = dmaengine_prep_slave_single(p->master->dma_tx,
+ desc_tx = dmaengine_prep_slave_single(p->ctlr->dma_tx,
p->tx_dma_addr, len, DMA_MEM_TO_DEV,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc_tx) {
@@ -803,9 +805,9 @@
/* Now start DMA */
if (rx)
- dma_async_issue_pending(p->master->dma_rx);
+ dma_async_issue_pending(p->ctlr->dma_rx);
if (tx)
- dma_async_issue_pending(p->master->dma_tx);
+ dma_async_issue_pending(p->ctlr->dma_tx);
ret = sh_msiof_spi_start(p, rx);
if (ret) {
@@ -845,9 +847,8 @@
}
if (rx)
- dma_sync_single_for_cpu(p->master->dma_rx->device->dev,
- p->rx_dma_addr, len,
- DMA_FROM_DEVICE);
+ dma_sync_single_for_cpu(p->ctlr->dma_rx->device->dev,
+ p->rx_dma_addr, len, DMA_FROM_DEVICE);
return 0;
@@ -856,10 +857,10 @@
sh_msiof_spi_stop(p, rx);
stop_dma:
if (tx)
- dmaengine_terminate_all(p->master->dma_tx);
+ dmaengine_terminate_all(p->ctlr->dma_tx);
no_dma_tx:
if (rx)
- dmaengine_terminate_all(p->master->dma_rx);
+ dmaengine_terminate_all(p->ctlr->dma_rx);
sh_msiof_write(p, IER, 0);
return ret;
}
@@ -907,11 +908,11 @@
memcpy(dst, src, words * 4);
}
-static int sh_msiof_transfer_one(struct spi_master *master,
+static int sh_msiof_transfer_one(struct spi_controller *ctlr,
struct spi_device *spi,
struct spi_transfer *t)
{
- struct sh_msiof_spi_priv *p = spi_master_get_devdata(master);
+ struct sh_msiof_spi_priv *p = spi_controller_get_devdata(ctlr);
void (*copy32)(u32 *, const u32 *, unsigned int);
void (*tx_fifo)(struct sh_msiof_spi_priv *, const void *, int, int);
void (*rx_fifo)(struct sh_msiof_spi_priv *, void *, int, int);
@@ -926,10 +927,10 @@
int ret;
/* setup clocks (clock already enabled in chipselect()) */
- if (!spi_controller_is_slave(p->master))
+ if (!spi_controller_is_slave(p->ctlr))
sh_msiof_spi_set_clk_regs(p, clk_get_rate(p->clk), t->speed_hz);
- while (master->dma_tx && len > 15) {
+ while (ctlr->dma_tx && len > 15) {
/*
* DMA supports 32-bit words only, hence pack 8-bit and 16-bit
* words, with byte resp. word swapping.
@@ -937,17 +938,13 @@
unsigned int l = 0;
if (tx_buf)
- l = min(len, p->tx_fifo_size * 4);
+ l = min(round_down(len, 4), p->tx_fifo_size * 4);
if (rx_buf)
- l = min(len, p->rx_fifo_size * 4);
+ l = min(round_down(len, 4), p->rx_fifo_size * 4);
if (bits <= 8) {
- if (l & 3)
- break;
copy32 = copy_bswap32;
} else if (bits <= 16) {
- if (l & 3)
- break;
copy32 = copy_wswap32;
} else {
copy32 = copy_plain32;
@@ -1052,23 +1049,28 @@
}
static const struct sh_msiof_chipdata sh_data = {
+ .bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32),
.tx_fifo_size = 64,
.rx_fifo_size = 64,
- .master_flags = 0,
+ .ctlr_flags = 0,
.min_div_pow = 0,
};
static const struct sh_msiof_chipdata rcar_gen2_data = {
+ .bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
+ SPI_BPW_MASK(24) | SPI_BPW_MASK(32),
.tx_fifo_size = 64,
.rx_fifo_size = 64,
- .master_flags = SPI_MASTER_MUST_TX,
+ .ctlr_flags = SPI_CONTROLLER_MUST_TX,
.min_div_pow = 0,
};
static const struct sh_msiof_chipdata rcar_gen3_data = {
+ .bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
+ SPI_BPW_MASK(24) | SPI_BPW_MASK(32),
.tx_fifo_size = 64,
.rx_fifo_size = 64,
- .master_flags = SPI_MASTER_MUST_TX,
+ .ctlr_flags = SPI_CONTROLLER_MUST_TX,
.min_div_pow = 1,
};
@@ -1136,7 +1138,7 @@
if (ret <= 0)
return 0;
- num_cs = max_t(unsigned int, ret, p->master->num_chipselect);
+ num_cs = max_t(unsigned int, ret, p->ctlr->num_chipselect);
for (i = 0; i < num_cs; i++) {
struct gpio_desc *gpiod;
@@ -1206,10 +1208,10 @@
{
struct platform_device *pdev = p->pdev;
struct device *dev = &pdev->dev;
- const struct sh_msiof_spi_info *info = dev_get_platdata(dev);
+ const struct sh_msiof_spi_info *info = p->info;
unsigned int dma_tx_id, dma_rx_id;
const struct resource *res;
- struct spi_master *master;
+ struct spi_controller *ctlr;
struct device *tx_dev, *rx_dev;
if (dev->of_node) {
@@ -1229,17 +1231,15 @@
if (!res)
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- master = p->master;
- master->dma_tx = sh_msiof_request_dma_chan(dev, DMA_MEM_TO_DEV,
- dma_tx_id,
- res->start + TFDR);
- if (!master->dma_tx)
+ ctlr = p->ctlr;
+ ctlr->dma_tx = sh_msiof_request_dma_chan(dev, DMA_MEM_TO_DEV,
+ dma_tx_id, res->start + TFDR);
+ if (!ctlr->dma_tx)
return -ENODEV;
- master->dma_rx = sh_msiof_request_dma_chan(dev, DMA_DEV_TO_MEM,
- dma_rx_id,
- res->start + RFDR);
- if (!master->dma_rx)
+ ctlr->dma_rx = sh_msiof_request_dma_chan(dev, DMA_DEV_TO_MEM,
+ dma_rx_id, res->start + RFDR);
+ if (!ctlr->dma_rx)
goto free_tx_chan;
p->tx_dma_page = (void *)__get_free_page(GFP_KERNEL | GFP_DMA);
@@ -1250,13 +1250,13 @@
if (!p->rx_dma_page)
goto free_tx_page;
- tx_dev = master->dma_tx->device->dev;
+ tx_dev = ctlr->dma_tx->device->dev;
p->tx_dma_addr = dma_map_single(tx_dev, p->tx_dma_page, PAGE_SIZE,
DMA_TO_DEVICE);
if (dma_mapping_error(tx_dev, p->tx_dma_addr))
goto free_rx_page;
- rx_dev = master->dma_rx->device->dev;
+ rx_dev = ctlr->dma_rx->device->dev;
p->rx_dma_addr = dma_map_single(rx_dev, p->rx_dma_page, PAGE_SIZE,
DMA_FROM_DEVICE);
if (dma_mapping_error(rx_dev, p->rx_dma_addr))
@@ -1272,34 +1272,34 @@
free_tx_page:
free_page((unsigned long)p->tx_dma_page);
free_rx_chan:
- dma_release_channel(master->dma_rx);
+ dma_release_channel(ctlr->dma_rx);
free_tx_chan:
- dma_release_channel(master->dma_tx);
- master->dma_tx = NULL;
+ dma_release_channel(ctlr->dma_tx);
+ ctlr->dma_tx = NULL;
return -ENODEV;
}
static void sh_msiof_release_dma(struct sh_msiof_spi_priv *p)
{
- struct spi_master *master = p->master;
+ struct spi_controller *ctlr = p->ctlr;
- if (!master->dma_tx)
+ if (!ctlr->dma_tx)
return;
- dma_unmap_single(master->dma_rx->device->dev, p->rx_dma_addr,
- PAGE_SIZE, DMA_FROM_DEVICE);
- dma_unmap_single(master->dma_tx->device->dev, p->tx_dma_addr,
- PAGE_SIZE, DMA_TO_DEVICE);
+ dma_unmap_single(ctlr->dma_rx->device->dev, p->rx_dma_addr, PAGE_SIZE,
+ DMA_FROM_DEVICE);
+ dma_unmap_single(ctlr->dma_tx->device->dev, p->tx_dma_addr, PAGE_SIZE,
+ DMA_TO_DEVICE);
free_page((unsigned long)p->rx_dma_page);
free_page((unsigned long)p->tx_dma_page);
- dma_release_channel(master->dma_rx);
- dma_release_channel(master->dma_tx);
+ dma_release_channel(ctlr->dma_rx);
+ dma_release_channel(ctlr->dma_tx);
}
static int sh_msiof_spi_probe(struct platform_device *pdev)
{
struct resource *r;
- struct spi_master *master;
+ struct spi_controller *ctlr;
const struct sh_msiof_chipdata *chipdata;
struct sh_msiof_spi_info *info;
struct sh_msiof_spi_priv *p;
@@ -1320,18 +1320,18 @@
}
if (info->mode == MSIOF_SPI_SLAVE)
- master = spi_alloc_slave(&pdev->dev,
- sizeof(struct sh_msiof_spi_priv));
+ ctlr = spi_alloc_slave(&pdev->dev,
+ sizeof(struct sh_msiof_spi_priv));
else
- master = spi_alloc_master(&pdev->dev,
- sizeof(struct sh_msiof_spi_priv));
- if (master == NULL)
+ ctlr = spi_alloc_master(&pdev->dev,
+ sizeof(struct sh_msiof_spi_priv));
+ if (ctlr == NULL)
return -ENOMEM;
- p = spi_master_get_devdata(master);
+ p = spi_controller_get_devdata(ctlr);
platform_set_drvdata(pdev, p);
- p->master = master;
+ p->ctlr = ctlr;
p->info = info;
p->min_div_pow = chipdata->min_div_pow;
@@ -1378,31 +1378,31 @@
p->rx_fifo_size = p->info->rx_fifo_override;
/* Setup GPIO chip selects */
- master->num_chipselect = p->info->num_chipselect;
+ ctlr->num_chipselect = p->info->num_chipselect;
ret = sh_msiof_get_cs_gpios(p);
if (ret)
goto err1;
- /* init master code */
- master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
- master->mode_bits |= SPI_LSB_FIRST | SPI_3WIRE;
- master->flags = chipdata->master_flags;
- master->bus_num = pdev->id;
- master->dev.of_node = pdev->dev.of_node;
- master->setup = sh_msiof_spi_setup;
- master->prepare_message = sh_msiof_prepare_message;
- master->slave_abort = sh_msiof_slave_abort;
- master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
- master->auto_runtime_pm = true;
- master->transfer_one = sh_msiof_transfer_one;
+ /* init controller code */
+ ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+ ctlr->mode_bits |= SPI_LSB_FIRST | SPI_3WIRE;
+ ctlr->flags = chipdata->ctlr_flags;
+ ctlr->bus_num = pdev->id;
+ ctlr->dev.of_node = pdev->dev.of_node;
+ ctlr->setup = sh_msiof_spi_setup;
+ ctlr->prepare_message = sh_msiof_prepare_message;
+ ctlr->slave_abort = sh_msiof_slave_abort;
+ ctlr->bits_per_word_mask = chipdata->bits_per_word_mask;
+ ctlr->auto_runtime_pm = true;
+ ctlr->transfer_one = sh_msiof_transfer_one;
ret = sh_msiof_request_dma(p);
if (ret < 0)
dev_warn(&pdev->dev, "DMA not available, using PIO\n");
- ret = devm_spi_register_master(&pdev->dev, master);
+ ret = devm_spi_register_controller(&pdev->dev, ctlr);
if (ret < 0) {
- dev_err(&pdev->dev, "spi_register_master error.\n");
+ dev_err(&pdev->dev, "devm_spi_register_controller error.\n");
goto err2;
}
@@ -1412,7 +1412,7 @@
sh_msiof_release_dma(p);
pm_runtime_disable(&pdev->dev);
err1:
- spi_master_put(master);
+ spi_controller_put(ctlr);
return ret;
}
@@ -1436,14 +1436,14 @@
{
struct sh_msiof_spi_priv *p = dev_get_drvdata(dev);
- return spi_master_suspend(p->master);
+ return spi_controller_suspend(p->ctlr);
}
static int sh_msiof_spi_resume(struct device *dev)
{
struct sh_msiof_spi_priv *p = dev_get_drvdata(dev);
- return spi_master_resume(p->master);
+ return spi_controller_resume(p->ctlr);
}
static SIMPLE_DEV_PM_OPS(sh_msiof_spi_pm_ops, sh_msiof_spi_suspend,
@@ -1465,7 +1465,7 @@
};
module_platform_driver(sh_msiof_spi_drv);
-MODULE_DESCRIPTION("SuperH MSIOF SPI Master Interface Driver");
+MODULE_DESCRIPTION("SuperH MSIOF SPI Controller Interface Driver");
MODULE_AUTHOR("Magnus Damm");
MODULE_LICENSE("GPL v2");
MODULE_ALIAS("platform:spi_sh_msiof");
diff --git a/drivers/spi/spi-sifive.c b/drivers/spi/spi-sifive.c
new file mode 100644
index 0000000..93ec2c6
--- /dev/null
+++ b/drivers/spi/spi-sifive.c
@@ -0,0 +1,448 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2018 SiFive, Inc.
+//
+// SiFive SPI controller driver (master mode only)
+//
+// Author: SiFive, Inc.
+// sifive@sifive.com
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/io.h>
+#include <linux/log2.h>
+
+#define SIFIVE_SPI_DRIVER_NAME "sifive_spi"
+
+#define SIFIVE_SPI_MAX_CS 32
+#define SIFIVE_SPI_DEFAULT_DEPTH 8
+#define SIFIVE_SPI_DEFAULT_MAX_BITS 8
+
+/* register offsets */
+#define SIFIVE_SPI_REG_SCKDIV 0x00 /* Serial clock divisor */
+#define SIFIVE_SPI_REG_SCKMODE 0x04 /* Serial clock mode */
+#define SIFIVE_SPI_REG_CSID 0x10 /* Chip select ID */
+#define SIFIVE_SPI_REG_CSDEF 0x14 /* Chip select default */
+#define SIFIVE_SPI_REG_CSMODE 0x18 /* Chip select mode */
+#define SIFIVE_SPI_REG_DELAY0 0x28 /* Delay control 0 */
+#define SIFIVE_SPI_REG_DELAY1 0x2c /* Delay control 1 */
+#define SIFIVE_SPI_REG_FMT 0x40 /* Frame format */
+#define SIFIVE_SPI_REG_TXDATA 0x48 /* Tx FIFO data */
+#define SIFIVE_SPI_REG_RXDATA 0x4c /* Rx FIFO data */
+#define SIFIVE_SPI_REG_TXMARK 0x50 /* Tx FIFO watermark */
+#define SIFIVE_SPI_REG_RXMARK 0x54 /* Rx FIFO watermark */
+#define SIFIVE_SPI_REG_FCTRL 0x60 /* SPI flash interface control */
+#define SIFIVE_SPI_REG_FFMT 0x64 /* SPI flash instruction format */
+#define SIFIVE_SPI_REG_IE 0x70 /* Interrupt Enable Register */
+#define SIFIVE_SPI_REG_IP 0x74 /* Interrupt Pendings Register */
+
+/* sckdiv bits */
+#define SIFIVE_SPI_SCKDIV_DIV_MASK 0xfffU
+
+/* sckmode bits */
+#define SIFIVE_SPI_SCKMODE_PHA BIT(0)
+#define SIFIVE_SPI_SCKMODE_POL BIT(1)
+#define SIFIVE_SPI_SCKMODE_MODE_MASK (SIFIVE_SPI_SCKMODE_PHA | \
+ SIFIVE_SPI_SCKMODE_POL)
+
+/* csmode bits */
+#define SIFIVE_SPI_CSMODE_MODE_AUTO 0U
+#define SIFIVE_SPI_CSMODE_MODE_HOLD 2U
+#define SIFIVE_SPI_CSMODE_MODE_OFF 3U
+
+/* delay0 bits */
+#define SIFIVE_SPI_DELAY0_CSSCK(x) ((u32)(x))
+#define SIFIVE_SPI_DELAY0_CSSCK_MASK 0xffU
+#define SIFIVE_SPI_DELAY0_SCKCS(x) ((u32)(x) << 16)
+#define SIFIVE_SPI_DELAY0_SCKCS_MASK (0xffU << 16)
+
+/* delay1 bits */
+#define SIFIVE_SPI_DELAY1_INTERCS(x) ((u32)(x))
+#define SIFIVE_SPI_DELAY1_INTERCS_MASK 0xffU
+#define SIFIVE_SPI_DELAY1_INTERXFR(x) ((u32)(x) << 16)
+#define SIFIVE_SPI_DELAY1_INTERXFR_MASK (0xffU << 16)
+
+/* fmt bits */
+#define SIFIVE_SPI_FMT_PROTO_SINGLE 0U
+#define SIFIVE_SPI_FMT_PROTO_DUAL 1U
+#define SIFIVE_SPI_FMT_PROTO_QUAD 2U
+#define SIFIVE_SPI_FMT_PROTO_MASK 3U
+#define SIFIVE_SPI_FMT_ENDIAN BIT(2)
+#define SIFIVE_SPI_FMT_DIR BIT(3)
+#define SIFIVE_SPI_FMT_LEN(x) ((u32)(x) << 16)
+#define SIFIVE_SPI_FMT_LEN_MASK (0xfU << 16)
+
+/* txdata bits */
+#define SIFIVE_SPI_TXDATA_DATA_MASK 0xffU
+#define SIFIVE_SPI_TXDATA_FULL BIT(31)
+
+/* rxdata bits */
+#define SIFIVE_SPI_RXDATA_DATA_MASK 0xffU
+#define SIFIVE_SPI_RXDATA_EMPTY BIT(31)
+
+/* ie and ip bits */
+#define SIFIVE_SPI_IP_TXWM BIT(0)
+#define SIFIVE_SPI_IP_RXWM BIT(1)
+
+struct sifive_spi {
+ void __iomem *regs; /* virt. address of control registers */
+ struct clk *clk; /* bus clock */
+ unsigned int fifo_depth; /* fifo depth in words */
+ u32 cs_inactive; /* level of the CS pins when inactive */
+ struct completion done; /* wake-up from interrupt */
+};
+
+static void sifive_spi_write(struct sifive_spi *spi, int offset, u32 value)
+{
+ iowrite32(value, spi->regs + offset);
+}
+
+static u32 sifive_spi_read(struct sifive_spi *spi, int offset)
+{
+ return ioread32(spi->regs + offset);
+}
+
+static void sifive_spi_init(struct sifive_spi *spi)
+{
+ /* Watermark interrupts are disabled by default */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0);
+
+ /* Default watermark FIFO threshold values */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_TXMARK, 1);
+ sifive_spi_write(spi, SIFIVE_SPI_REG_RXMARK, 0);
+
+ /* Set CS/SCK Delays and Inactive Time to defaults */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_DELAY0,
+ SIFIVE_SPI_DELAY0_CSSCK(1) |
+ SIFIVE_SPI_DELAY0_SCKCS(1));
+ sifive_spi_write(spi, SIFIVE_SPI_REG_DELAY1,
+ SIFIVE_SPI_DELAY1_INTERCS(1) |
+ SIFIVE_SPI_DELAY1_INTERXFR(0));
+
+ /* Exit specialized memory-mapped SPI flash mode */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_FCTRL, 0);
+}
+
+static int
+sifive_spi_prepare_message(struct spi_master *master, struct spi_message *msg)
+{
+ struct sifive_spi *spi = spi_master_get_devdata(master);
+ struct spi_device *device = msg->spi;
+
+ /* Update the chip select polarity */
+ if (device->mode & SPI_CS_HIGH)
+ spi->cs_inactive &= ~BIT(device->chip_select);
+ else
+ spi->cs_inactive |= BIT(device->chip_select);
+ sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive);
+
+ /* Select the correct device */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_CSID, device->chip_select);
+
+ /* Set clock mode */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_SCKMODE,
+ device->mode & SIFIVE_SPI_SCKMODE_MODE_MASK);
+
+ return 0;
+}
+
+static void sifive_spi_set_cs(struct spi_device *device, bool is_high)
+{
+ struct sifive_spi *spi = spi_master_get_devdata(device->master);
+
+ /* Reverse polarity is handled by SCMR/CPOL. Not inverted CS. */
+ if (device->mode & SPI_CS_HIGH)
+ is_high = !is_high;
+
+ sifive_spi_write(spi, SIFIVE_SPI_REG_CSMODE, is_high ?
+ SIFIVE_SPI_CSMODE_MODE_AUTO :
+ SIFIVE_SPI_CSMODE_MODE_HOLD);
+}
+
+static int
+sifive_spi_prep_transfer(struct sifive_spi *spi, struct spi_device *device,
+ struct spi_transfer *t)
+{
+ u32 cr;
+ unsigned int mode;
+
+ /* Calculate and program the clock rate */
+ cr = DIV_ROUND_UP(clk_get_rate(spi->clk) >> 1, t->speed_hz) - 1;
+ cr &= SIFIVE_SPI_SCKDIV_DIV_MASK;
+ sifive_spi_write(spi, SIFIVE_SPI_REG_SCKDIV, cr);
+
+ mode = max_t(unsigned int, t->rx_nbits, t->tx_nbits);
+
+ /* Set frame format */
+ cr = SIFIVE_SPI_FMT_LEN(t->bits_per_word);
+ switch (mode) {
+ case SPI_NBITS_QUAD:
+ cr |= SIFIVE_SPI_FMT_PROTO_QUAD;
+ break;
+ case SPI_NBITS_DUAL:
+ cr |= SIFIVE_SPI_FMT_PROTO_DUAL;
+ break;
+ default:
+ cr |= SIFIVE_SPI_FMT_PROTO_SINGLE;
+ break;
+ }
+ if (device->mode & SPI_LSB_FIRST)
+ cr |= SIFIVE_SPI_FMT_ENDIAN;
+ if (!t->rx_buf)
+ cr |= SIFIVE_SPI_FMT_DIR;
+ sifive_spi_write(spi, SIFIVE_SPI_REG_FMT, cr);
+
+ /* We will want to poll if the time we need to wait is
+ * less than the context switching time.
+ * Let's call that threshold 5us. The operation will take:
+ * (8/mode) * fifo_depth / hz <= 5 * 10^-6
+ * 1600000 * fifo_depth <= hz * mode
+ */
+ return 1600000 * spi->fifo_depth <= t->speed_hz * mode;
+}
+
+static irqreturn_t sifive_spi_irq(int irq, void *dev_id)
+{
+ struct sifive_spi *spi = dev_id;
+ u32 ip = sifive_spi_read(spi, SIFIVE_SPI_REG_IP);
+
+ if (ip & (SIFIVE_SPI_IP_TXWM | SIFIVE_SPI_IP_RXWM)) {
+ /* Disable interrupts until next transfer */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0);
+ complete(&spi->done);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static void sifive_spi_wait(struct sifive_spi *spi, u32 bit, int poll)
+{
+ if (poll) {
+ u32 cr;
+
+ do {
+ cr = sifive_spi_read(spi, SIFIVE_SPI_REG_IP);
+ } while (!(cr & bit));
+ } else {
+ reinit_completion(&spi->done);
+ sifive_spi_write(spi, SIFIVE_SPI_REG_IE, bit);
+ wait_for_completion(&spi->done);
+ }
+}
+
+static void sifive_spi_tx(struct sifive_spi *spi, const u8 *tx_ptr)
+{
+ WARN_ON_ONCE((sifive_spi_read(spi, SIFIVE_SPI_REG_TXDATA)
+ & SIFIVE_SPI_TXDATA_FULL) != 0);
+ sifive_spi_write(spi, SIFIVE_SPI_REG_TXDATA,
+ *tx_ptr & SIFIVE_SPI_TXDATA_DATA_MASK);
+}
+
+static void sifive_spi_rx(struct sifive_spi *spi, u8 *rx_ptr)
+{
+ u32 data = sifive_spi_read(spi, SIFIVE_SPI_REG_RXDATA);
+
+ WARN_ON_ONCE((data & SIFIVE_SPI_RXDATA_EMPTY) != 0);
+ *rx_ptr = data & SIFIVE_SPI_RXDATA_DATA_MASK;
+}
+
+static int
+sifive_spi_transfer_one(struct spi_master *master, struct spi_device *device,
+ struct spi_transfer *t)
+{
+ struct sifive_spi *spi = spi_master_get_devdata(master);
+ int poll = sifive_spi_prep_transfer(spi, device, t);
+ const u8 *tx_ptr = t->tx_buf;
+ u8 *rx_ptr = t->rx_buf;
+ unsigned int remaining_words = t->len;
+
+ while (remaining_words) {
+ unsigned int n_words = min(remaining_words, spi->fifo_depth);
+ unsigned int i;
+
+ /* Enqueue n_words for transmission */
+ for (i = 0; i < n_words; i++)
+ sifive_spi_tx(spi, tx_ptr++);
+
+ if (rx_ptr) {
+ /* Wait for transmission + reception to complete */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_RXMARK,
+ n_words - 1);
+ sifive_spi_wait(spi, SIFIVE_SPI_IP_RXWM, poll);
+
+ /* Read out all the data from the RX FIFO */
+ for (i = 0; i < n_words; i++)
+ sifive_spi_rx(spi, rx_ptr++);
+ } else {
+ /* Wait for transmission to complete */
+ sifive_spi_wait(spi, SIFIVE_SPI_IP_TXWM, poll);
+ }
+
+ remaining_words -= n_words;
+ }
+
+ return 0;
+}
+
+static int sifive_spi_probe(struct platform_device *pdev)
+{
+ struct sifive_spi *spi;
+ struct resource *res;
+ int ret, irq, num_cs;
+ u32 cs_bits, max_bits_per_word;
+ struct spi_master *master;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct sifive_spi));
+ if (!master) {
+ dev_err(&pdev->dev, "out of memory\n");
+ return -ENOMEM;
+ }
+
+ spi = spi_master_get_devdata(master);
+ init_completion(&spi->done);
+ platform_set_drvdata(pdev, master);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ spi->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spi->regs)) {
+ ret = PTR_ERR(spi->regs);
+ goto put_master;
+ }
+
+ spi->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(spi->clk)) {
+ dev_err(&pdev->dev, "Unable to find bus clock\n");
+ ret = PTR_ERR(spi->clk);
+ goto put_master;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "Unable to find interrupt\n");
+ ret = irq;
+ goto put_master;
+ }
+
+ /* Optional parameters */
+ ret =
+ of_property_read_u32(pdev->dev.of_node, "sifive,fifo-depth",
+ &spi->fifo_depth);
+ if (ret < 0)
+ spi->fifo_depth = SIFIVE_SPI_DEFAULT_DEPTH;
+
+ ret =
+ of_property_read_u32(pdev->dev.of_node, "sifive,max-bits-per-word",
+ &max_bits_per_word);
+
+ if (!ret && max_bits_per_word < 8) {
+ dev_err(&pdev->dev, "Only 8bit SPI words supported by the driver\n");
+ ret = -EINVAL;
+ goto put_master;
+ }
+
+ /* Spin up the bus clock before hitting registers */
+ ret = clk_prepare_enable(spi->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to enable bus clock\n");
+ goto put_master;
+ }
+
+ /* probe the number of CS lines */
+ spi->cs_inactive = sifive_spi_read(spi, SIFIVE_SPI_REG_CSDEF);
+ sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, 0xffffffffU);
+ cs_bits = sifive_spi_read(spi, SIFIVE_SPI_REG_CSDEF);
+ sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive);
+ if (!cs_bits) {
+ dev_err(&pdev->dev, "Could not auto probe CS lines\n");
+ ret = -EINVAL;
+ goto put_master;
+ }
+
+ num_cs = ilog2(cs_bits) + 1;
+ if (num_cs > SIFIVE_SPI_MAX_CS) {
+ dev_err(&pdev->dev, "Invalid number of spi slaves\n");
+ ret = -EINVAL;
+ goto put_master;
+ }
+
+ /* Define our master */
+ master->dev.of_node = pdev->dev.of_node;
+ master->bus_num = pdev->id;
+ master->num_chipselect = num_cs;
+ master->mode_bits = SPI_CPHA | SPI_CPOL
+ | SPI_CS_HIGH | SPI_LSB_FIRST
+ | SPI_TX_DUAL | SPI_TX_QUAD
+ | SPI_RX_DUAL | SPI_RX_QUAD;
+ /* TODO: add driver support for bits_per_word < 8
+ * we need to "left-align" the bits (unless SPI_LSB_FIRST)
+ */
+ master->bits_per_word_mask = SPI_BPW_MASK(8);
+ master->flags = SPI_CONTROLLER_MUST_TX | SPI_MASTER_GPIO_SS;
+ master->prepare_message = sifive_spi_prepare_message;
+ master->set_cs = sifive_spi_set_cs;
+ master->transfer_one = sifive_spi_transfer_one;
+
+ pdev->dev.dma_mask = NULL;
+ /* Configure the SPI master hardware */
+ sifive_spi_init(spi);
+
+ /* Register for SPI Interrupt */
+ ret = devm_request_irq(&pdev->dev, irq, sifive_spi_irq, 0,
+ dev_name(&pdev->dev), spi);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to bind to interrupt\n");
+ goto put_master;
+ }
+
+ dev_info(&pdev->dev, "mapped; irq=%d, cs=%d\n",
+ irq, master->num_chipselect);
+
+ ret = devm_spi_register_master(&pdev->dev, master);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "spi_register_master failed\n");
+ goto put_master;
+ }
+
+ return 0;
+
+put_master:
+ spi_master_put(master);
+
+ return ret;
+}
+
+static int sifive_spi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct sifive_spi *spi = spi_master_get_devdata(master);
+
+ /* Disable all the interrupts just in case */
+ sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0);
+
+ return 0;
+}
+
+static const struct of_device_id sifive_spi_of_match[] = {
+ { .compatible = "sifive,spi0", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sifive_spi_of_match);
+
+static struct platform_driver sifive_spi_driver = {
+ .probe = sifive_spi_probe,
+ .remove = sifive_spi_remove,
+ .driver = {
+ .name = SIFIVE_SPI_DRIVER_NAME,
+ .of_match_table = sifive_spi_of_match,
+ },
+};
+module_platform_driver(sifive_spi_driver);
+
+MODULE_AUTHOR("SiFive, Inc. <sifive@sifive.com>");
+MODULE_DESCRIPTION("SiFive SPI driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/spi/spi-sprd.c b/drivers/spi/spi-sprd.c
index 8daa24e..1b7eebb 100644
--- a/drivers/spi/spi-sprd.c
+++ b/drivers/spi/spi-sprd.c
@@ -2,6 +2,9 @@
// Copyright (C) 2018 Spreadtrum Communications Inc.
#include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/dma/sprd-dma.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
@@ -9,6 +12,7 @@
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
+#include <linux/of_dma.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/spi/spi.h>
@@ -128,11 +132,28 @@
#define SPRD_SPI_DEFAULT_SOURCE 26000000
#define SPRD_SPI_MAX_SPEED_HZ 48000000
#define SPRD_SPI_AUTOSUSPEND_DELAY 100
+#define SPRD_SPI_DMA_STEP 8
+
+enum sprd_spi_dma_channel {
+ SPRD_SPI_RX,
+ SPRD_SPI_TX,
+ SPRD_SPI_MAX,
+};
+
+struct sprd_spi_dma {
+ bool enable;
+ struct dma_chan *dma_chan[SPRD_SPI_MAX];
+ enum dma_slave_buswidth width;
+ u32 fragmens_len;
+ u32 rx_len;
+};
struct sprd_spi {
void __iomem *base;
+ phys_addr_t phy_base;
struct device *dev;
struct clk *clk;
+ int irq;
u32 src_clk;
u32 hw_mode;
u32 trans_len;
@@ -141,6 +162,8 @@
u32 hw_speed_hz;
u32 len;
int status;
+ struct sprd_spi_dma dma;
+ struct completion xfer_completion;
const void *tx_buf;
void *rx_buf;
int (*read_bufs)(struct sprd_spi *ss, u32 len);
@@ -380,7 +403,7 @@
{
struct sprd_spi *ss = spi_controller_get_devdata(sdev->controller);
u32 trans_len = ss->trans_len, len;
- int ret, write_size = 0;
+ int ret, write_size = 0, read_size = 0;
while (trans_len) {
len = trans_len > SPRD_SPI_FIFO_SIZE ? SPRD_SPI_FIFO_SIZE :
@@ -416,19 +439,223 @@
goto complete;
if (ss->trans_mode & SPRD_SPI_RX_MODE)
- ss->read_bufs(ss, len);
+ read_size += ss->read_bufs(ss, len);
trans_len -= len;
}
- ret = write_size;
-
+ if (ss->trans_mode & SPRD_SPI_TX_MODE)
+ ret = write_size;
+ else
+ ret = read_size;
complete:
sprd_spi_enter_idle(ss);
return ret;
}
+static void sprd_spi_irq_enable(struct sprd_spi *ss)
+{
+ u32 val;
+
+ /* Clear interrupt status before enabling interrupt. */
+ writel_relaxed(SPRD_SPI_TX_END_CLR | SPRD_SPI_RX_END_CLR,
+ ss->base + SPRD_SPI_INT_CLR);
+ /* Enable SPI interrupt only in DMA mode. */
+ val = readl_relaxed(ss->base + SPRD_SPI_INT_EN);
+ writel_relaxed(val | SPRD_SPI_TX_END_INT_EN |
+ SPRD_SPI_RX_END_INT_EN,
+ ss->base + SPRD_SPI_INT_EN);
+}
+
+static void sprd_spi_irq_disable(struct sprd_spi *ss)
+{
+ writel_relaxed(0, ss->base + SPRD_SPI_INT_EN);
+}
+
+static void sprd_spi_dma_enable(struct sprd_spi *ss, bool enable)
+{
+ u32 val = readl_relaxed(ss->base + SPRD_SPI_CTL2);
+
+ if (enable)
+ val |= SPRD_SPI_DMA_EN;
+ else
+ val &= ~SPRD_SPI_DMA_EN;
+
+ writel_relaxed(val, ss->base + SPRD_SPI_CTL2);
+}
+
+static int sprd_spi_dma_submit(struct dma_chan *dma_chan,
+ struct dma_slave_config *c,
+ struct sg_table *sg,
+ enum dma_transfer_direction dir)
+{
+ struct dma_async_tx_descriptor *desc;
+ dma_cookie_t cookie;
+ unsigned long flags;
+ int ret;
+
+ ret = dmaengine_slave_config(dma_chan, c);
+ if (ret < 0)
+ return ret;
+
+ flags = SPRD_DMA_FLAGS(SPRD_DMA_CHN_MODE_NONE, SPRD_DMA_NO_TRG,
+ SPRD_DMA_FRAG_REQ, SPRD_DMA_TRANS_INT);
+ desc = dmaengine_prep_slave_sg(dma_chan, sg->sgl, sg->nents, dir, flags);
+ if (!desc)
+ return -ENODEV;
+
+ cookie = dmaengine_submit(desc);
+ if (dma_submit_error(cookie))
+ return dma_submit_error(cookie);
+
+ dma_async_issue_pending(dma_chan);
+
+ return 0;
+}
+
+static int sprd_spi_dma_rx_config(struct sprd_spi *ss, struct spi_transfer *t)
+{
+ struct dma_chan *dma_chan = ss->dma.dma_chan[SPRD_SPI_RX];
+ struct dma_slave_config config = {
+ .src_addr = ss->phy_base,
+ .src_addr_width = ss->dma.width,
+ .dst_addr_width = ss->dma.width,
+ .dst_maxburst = ss->dma.fragmens_len,
+ };
+ int ret;
+
+ ret = sprd_spi_dma_submit(dma_chan, &config, &t->rx_sg, DMA_DEV_TO_MEM);
+ if (ret)
+ return ret;
+
+ return ss->dma.rx_len;
+}
+
+static int sprd_spi_dma_tx_config(struct sprd_spi *ss, struct spi_transfer *t)
+{
+ struct dma_chan *dma_chan = ss->dma.dma_chan[SPRD_SPI_TX];
+ struct dma_slave_config config = {
+ .dst_addr = ss->phy_base,
+ .src_addr_width = ss->dma.width,
+ .dst_addr_width = ss->dma.width,
+ .src_maxburst = ss->dma.fragmens_len,
+ };
+ int ret;
+
+ ret = sprd_spi_dma_submit(dma_chan, &config, &t->tx_sg, DMA_MEM_TO_DEV);
+ if (ret)
+ return ret;
+
+ return t->len;
+}
+
+static int sprd_spi_dma_request(struct sprd_spi *ss)
+{
+ ss->dma.dma_chan[SPRD_SPI_RX] = dma_request_chan(ss->dev, "rx_chn");
+ if (IS_ERR_OR_NULL(ss->dma.dma_chan[SPRD_SPI_RX])) {
+ if (PTR_ERR(ss->dma.dma_chan[SPRD_SPI_RX]) == -EPROBE_DEFER)
+ return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_RX]);
+
+ dev_err(ss->dev, "request RX DMA channel failed!\n");
+ return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_RX]);
+ }
+
+ ss->dma.dma_chan[SPRD_SPI_TX] = dma_request_chan(ss->dev, "tx_chn");
+ if (IS_ERR_OR_NULL(ss->dma.dma_chan[SPRD_SPI_TX])) {
+ if (PTR_ERR(ss->dma.dma_chan[SPRD_SPI_TX]) == -EPROBE_DEFER)
+ return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_TX]);
+
+ dev_err(ss->dev, "request TX DMA channel failed!\n");
+ dma_release_channel(ss->dma.dma_chan[SPRD_SPI_RX]);
+ return PTR_ERR(ss->dma.dma_chan[SPRD_SPI_TX]);
+ }
+
+ return 0;
+}
+
+static void sprd_spi_dma_release(struct sprd_spi *ss)
+{
+ if (ss->dma.dma_chan[SPRD_SPI_RX])
+ dma_release_channel(ss->dma.dma_chan[SPRD_SPI_RX]);
+
+ if (ss->dma.dma_chan[SPRD_SPI_TX])
+ dma_release_channel(ss->dma.dma_chan[SPRD_SPI_TX]);
+}
+
+static int sprd_spi_dma_txrx_bufs(struct spi_device *sdev,
+ struct spi_transfer *t)
+{
+ struct sprd_spi *ss = spi_master_get_devdata(sdev->master);
+ u32 trans_len = ss->trans_len;
+ int ret, write_size = 0;
+
+ reinit_completion(&ss->xfer_completion);
+ sprd_spi_irq_enable(ss);
+ if (ss->trans_mode & SPRD_SPI_TX_MODE) {
+ write_size = sprd_spi_dma_tx_config(ss, t);
+ sprd_spi_set_tx_length(ss, trans_len);
+
+ /*
+ * For our 3 wires mode or dual TX line mode, we need
+ * to request the controller to transfer.
+ */
+ if (ss->hw_mode & SPI_3WIRE || ss->hw_mode & SPI_TX_DUAL)
+ sprd_spi_tx_req(ss);
+ } else {
+ sprd_spi_set_rx_length(ss, trans_len);
+
+ /*
+ * For our 3 wires mode or dual TX line mode, we need
+ * to request the controller to read.
+ */
+ if (ss->hw_mode & SPI_3WIRE || ss->hw_mode & SPI_TX_DUAL)
+ sprd_spi_rx_req(ss);
+ else
+ write_size = ss->write_bufs(ss, trans_len);
+ }
+
+ if (write_size < 0) {
+ ret = write_size;
+ dev_err(ss->dev, "failed to write, ret = %d\n", ret);
+ goto trans_complete;
+ }
+
+ if (ss->trans_mode & SPRD_SPI_RX_MODE) {
+ /*
+ * Set up the DMA receive data length, which must be an
+ * integral multiple of fragment length. But when the length
+ * of received data is less than fragment length, DMA can be
+ * configured to receive data according to the actual length
+ * of received data.
+ */
+ ss->dma.rx_len = t->len > ss->dma.fragmens_len ?
+ (t->len - t->len % ss->dma.fragmens_len) :
+ t->len;
+ ret = sprd_spi_dma_rx_config(ss, t);
+ if (ret < 0) {
+ dev_err(&sdev->dev,
+ "failed to configure rx DMA, ret = %d\n", ret);
+ goto trans_complete;
+ }
+ }
+
+ sprd_spi_dma_enable(ss, true);
+ wait_for_completion(&(ss->xfer_completion));
+
+ if (ss->trans_mode & SPRD_SPI_TX_MODE)
+ ret = write_size;
+ else
+ ret = ss->dma.rx_len;
+
+trans_complete:
+ sprd_spi_dma_enable(ss, false);
+ sprd_spi_enter_idle(ss);
+ sprd_spi_irq_disable(ss);
+
+ return ret;
+}
+
static void sprd_spi_set_speed(struct sprd_spi *ss, u32 speed_hz)
{
/*
@@ -514,16 +741,22 @@
ss->trans_len = t->len;
ss->read_bufs = sprd_spi_read_bufs_u8;
ss->write_bufs = sprd_spi_write_bufs_u8;
+ ss->dma.width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ ss->dma.fragmens_len = SPRD_SPI_DMA_STEP;
break;
case 16:
ss->trans_len = t->len >> 1;
ss->read_bufs = sprd_spi_read_bufs_u16;
ss->write_bufs = sprd_spi_write_bufs_u16;
+ ss->dma.width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ ss->dma.fragmens_len = SPRD_SPI_DMA_STEP << 1;
break;
case 32:
ss->trans_len = t->len >> 2;
ss->read_bufs = sprd_spi_read_bufs_u32;
ss->write_bufs = sprd_spi_write_bufs_u32;
+ ss->dma.width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ ss->dma.fragmens_len = SPRD_SPI_DMA_STEP << 2;
break;
default:
return -EINVAL;
@@ -561,7 +794,11 @@
if (ret)
goto setup_err;
- ret = sprd_spi_txrx_bufs(sdev, t);
+ if (sctlr->can_dma(sctlr, sdev, t))
+ ret = sprd_spi_dma_txrx_bufs(sdev, t);
+ else
+ ret = sprd_spi_txrx_bufs(sdev, t);
+
if (ret == t->len)
ret = 0;
else if (ret >= 0)
@@ -573,6 +810,53 @@
return ret;
}
+static irqreturn_t sprd_spi_handle_irq(int irq, void *data)
+{
+ struct sprd_spi *ss = (struct sprd_spi *)data;
+ u32 val = readl_relaxed(ss->base + SPRD_SPI_INT_MASK_STS);
+
+ if (val & SPRD_SPI_MASK_TX_END) {
+ writel_relaxed(SPRD_SPI_TX_END_CLR, ss->base + SPRD_SPI_INT_CLR);
+ if (!(ss->trans_mode & SPRD_SPI_RX_MODE))
+ complete(&ss->xfer_completion);
+
+ return IRQ_HANDLED;
+ }
+
+ if (val & SPRD_SPI_MASK_RX_END) {
+ writel_relaxed(SPRD_SPI_RX_END_CLR, ss->base + SPRD_SPI_INT_CLR);
+ if (ss->dma.rx_len < ss->len) {
+ ss->rx_buf += ss->dma.rx_len;
+ ss->dma.rx_len +=
+ ss->read_bufs(ss, ss->len - ss->dma.rx_len);
+ }
+ complete(&ss->xfer_completion);
+
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static int sprd_spi_irq_init(struct platform_device *pdev, struct sprd_spi *ss)
+{
+ int ret;
+
+ ss->irq = platform_get_irq(pdev, 0);
+ if (ss->irq < 0) {
+ dev_err(&pdev->dev, "failed to get irq resource\n");
+ return ss->irq;
+ }
+
+ ret = devm_request_irq(&pdev->dev, ss->irq, sprd_spi_handle_irq,
+ 0, pdev->name, ss);
+ if (ret)
+ dev_err(&pdev->dev, "failed to request spi irq %d, ret = %d\n",
+ ss->irq, ret);
+
+ return ret;
+}
+
static int sprd_spi_clk_init(struct platform_device *pdev, struct sprd_spi *ss)
{
struct clk *clk_spi, *clk_parent;
@@ -603,6 +887,35 @@
return 0;
}
+static bool sprd_spi_can_dma(struct spi_controller *sctlr,
+ struct spi_device *spi, struct spi_transfer *t)
+{
+ struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
+
+ return ss->dma.enable && (t->len > SPRD_SPI_FIFO_SIZE);
+}
+
+static int sprd_spi_dma_init(struct platform_device *pdev, struct sprd_spi *ss)
+{
+ int ret;
+
+ ret = sprd_spi_dma_request(ss);
+ if (ret) {
+ if (ret == -EPROBE_DEFER)
+ return ret;
+
+ dev_warn(&pdev->dev,
+ "failed to request dma, enter no dma mode, ret = %d\n",
+ ret);
+
+ return 0;
+ }
+
+ ss->dma.enable = true;
+
+ return 0;
+}
+
static int sprd_spi_probe(struct platform_device *pdev)
{
struct spi_controller *sctlr;
@@ -623,25 +936,36 @@
goto free_controller;
}
+ ss->phy_base = res->start;
ss->dev = &pdev->dev;
sctlr->dev.of_node = pdev->dev.of_node;
sctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_3WIRE | SPI_TX_DUAL;
sctlr->bus_num = pdev->id;
sctlr->set_cs = sprd_spi_chipselect;
sctlr->transfer_one = sprd_spi_transfer_one;
+ sctlr->can_dma = sprd_spi_can_dma;
sctlr->auto_runtime_pm = true;
sctlr->max_speed_hz = min_t(u32, ss->src_clk >> 1,
SPRD_SPI_MAX_SPEED_HZ);
+ init_completion(&ss->xfer_completion);
platform_set_drvdata(pdev, sctlr);
ret = sprd_spi_clk_init(pdev, ss);
if (ret)
goto free_controller;
- ret = clk_prepare_enable(ss->clk);
+ ret = sprd_spi_irq_init(pdev, ss);
if (ret)
goto free_controller;
+ ret = sprd_spi_dma_init(pdev, ss);
+ if (ret)
+ goto free_controller;
+
+ ret = clk_prepare_enable(ss->clk);
+ if (ret)
+ goto release_dma;
+
ret = pm_runtime_set_active(&pdev->dev);
if (ret < 0)
goto disable_clk;
@@ -670,6 +994,8 @@
pm_runtime_disable(&pdev->dev);
disable_clk:
clk_disable_unprepare(ss->clk);
+release_dma:
+ sprd_spi_dma_release(ss);
free_controller:
spi_controller_put(sctlr);
@@ -688,6 +1014,10 @@
return ret;
}
+ spi_controller_suspend(sctlr);
+
+ if (ss->dma.enable)
+ sprd_spi_dma_release(ss);
clk_disable_unprepare(ss->clk);
pm_runtime_put_noidle(&pdev->dev);
pm_runtime_disable(&pdev->dev);
@@ -700,6 +1030,9 @@
struct spi_controller *sctlr = dev_get_drvdata(dev);
struct sprd_spi *ss = spi_controller_get_devdata(sctlr);
+ if (ss->dma.enable)
+ sprd_spi_dma_release(ss);
+
clk_disable_unprepare(ss->clk);
return 0;
@@ -715,7 +1048,14 @@
if (ret)
return ret;
- return 0;
+ if (!ss->dma.enable)
+ return 0;
+
+ ret = sprd_spi_dma_request(ss);
+ if (ret)
+ clk_disable_unprepare(ss->clk);
+
+ return ret;
}
static const struct dev_pm_ops sprd_spi_pm_ops = {
diff --git a/drivers/spi/spi-stm32.c b/drivers/spi/spi-stm32.c
index ad1e55d..4186ed2 100644
--- a/drivers/spi/spi-stm32.c
+++ b/drivers/spi/spi-stm32.c
@@ -1,23 +1,10 @@
-/*
- * STMicroelectronics STM32 SPI Controller driver (master mode only)
- *
- * Copyright (C) 2017, STMicroelectronics - All Rights Reserved
- * Author(s): Amelie Delaunay <amelie.delaunay@st.com> for STMicroelectronics.
- *
- * License terms: GPL V2.0.
- *
- * spi_stm32 driver is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published by
- * the Free Software Foundation.
- *
- * spi_stm32 driver is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
- * details.
- *
- * You should have received a copy of the GNU General Public License along with
- * spi_stm32 driver. If not, see <http://www.gnu.org/licenses/>.
- */
+// SPDX-License-Identifier: GPL-2.0
+//
+// STMicroelectronics STM32 SPI Controller driver (master mode only)
+//
+// Copyright (C) 2017, STMicroelectronics - All Rights Reserved
+// Author(s): Amelie Delaunay <amelie.delaunay@st.com> for STMicroelectronics.
+
#include <linux/debugfs.h>
#include <linux/clk.h>
#include <linux/delay.h>
@@ -33,99 +20,251 @@
#define DRIVER_NAME "spi_stm32"
-/* STM32 SPI registers */
-#define STM32_SPI_CR1 0x00
-#define STM32_SPI_CR2 0x04
-#define STM32_SPI_CFG1 0x08
-#define STM32_SPI_CFG2 0x0C
-#define STM32_SPI_IER 0x10
-#define STM32_SPI_SR 0x14
-#define STM32_SPI_IFCR 0x18
-#define STM32_SPI_TXDR 0x20
-#define STM32_SPI_RXDR 0x30
-#define STM32_SPI_I2SCFGR 0x50
+/* STM32F4 SPI registers */
+#define STM32F4_SPI_CR1 0x00
+#define STM32F4_SPI_CR2 0x04
+#define STM32F4_SPI_SR 0x08
+#define STM32F4_SPI_DR 0x0C
+#define STM32F4_SPI_I2SCFGR 0x1C
-/* STM32_SPI_CR1 bit fields */
-#define SPI_CR1_SPE BIT(0)
-#define SPI_CR1_MASRX BIT(8)
-#define SPI_CR1_CSTART BIT(9)
-#define SPI_CR1_CSUSP BIT(10)
-#define SPI_CR1_HDDIR BIT(11)
-#define SPI_CR1_SSI BIT(12)
+/* STM32F4_SPI_CR1 bit fields */
+#define STM32F4_SPI_CR1_CPHA BIT(0)
+#define STM32F4_SPI_CR1_CPOL BIT(1)
+#define STM32F4_SPI_CR1_MSTR BIT(2)
+#define STM32F4_SPI_CR1_BR_SHIFT 3
+#define STM32F4_SPI_CR1_BR GENMASK(5, 3)
+#define STM32F4_SPI_CR1_SPE BIT(6)
+#define STM32F4_SPI_CR1_LSBFRST BIT(7)
+#define STM32F4_SPI_CR1_SSI BIT(8)
+#define STM32F4_SPI_CR1_SSM BIT(9)
+#define STM32F4_SPI_CR1_RXONLY BIT(10)
+#define STM32F4_SPI_CR1_DFF BIT(11)
+#define STM32F4_SPI_CR1_CRCNEXT BIT(12)
+#define STM32F4_SPI_CR1_CRCEN BIT(13)
+#define STM32F4_SPI_CR1_BIDIOE BIT(14)
+#define STM32F4_SPI_CR1_BIDIMODE BIT(15)
+#define STM32F4_SPI_CR1_BR_MIN 0
+#define STM32F4_SPI_CR1_BR_MAX (GENMASK(5, 3) >> 3)
-/* STM32_SPI_CR2 bit fields */
-#define SPI_CR2_TSIZE_SHIFT 0
-#define SPI_CR2_TSIZE GENMASK(15, 0)
+/* STM32F4_SPI_CR2 bit fields */
+#define STM32F4_SPI_CR2_RXDMAEN BIT(0)
+#define STM32F4_SPI_CR2_TXDMAEN BIT(1)
+#define STM32F4_SPI_CR2_SSOE BIT(2)
+#define STM32F4_SPI_CR2_FRF BIT(4)
+#define STM32F4_SPI_CR2_ERRIE BIT(5)
+#define STM32F4_SPI_CR2_RXNEIE BIT(6)
+#define STM32F4_SPI_CR2_TXEIE BIT(7)
-/* STM32_SPI_CFG1 bit fields */
-#define SPI_CFG1_DSIZE_SHIFT 0
-#define SPI_CFG1_DSIZE GENMASK(4, 0)
-#define SPI_CFG1_FTHLV_SHIFT 5
-#define SPI_CFG1_FTHLV GENMASK(8, 5)
-#define SPI_CFG1_RXDMAEN BIT(14)
-#define SPI_CFG1_TXDMAEN BIT(15)
-#define SPI_CFG1_MBR_SHIFT 28
-#define SPI_CFG1_MBR GENMASK(30, 28)
-#define SPI_CFG1_MBR_MIN 0
-#define SPI_CFG1_MBR_MAX (GENMASK(30, 28) >> 28)
+/* STM32F4_SPI_SR bit fields */
+#define STM32F4_SPI_SR_RXNE BIT(0)
+#define STM32F4_SPI_SR_TXE BIT(1)
+#define STM32F4_SPI_SR_CHSIDE BIT(2)
+#define STM32F4_SPI_SR_UDR BIT(3)
+#define STM32F4_SPI_SR_CRCERR BIT(4)
+#define STM32F4_SPI_SR_MODF BIT(5)
+#define STM32F4_SPI_SR_OVR BIT(6)
+#define STM32F4_SPI_SR_BSY BIT(7)
+#define STM32F4_SPI_SR_FRE BIT(8)
-/* STM32_SPI_CFG2 bit fields */
-#define SPI_CFG2_MIDI_SHIFT 4
-#define SPI_CFG2_MIDI GENMASK(7, 4)
-#define SPI_CFG2_COMM_SHIFT 17
-#define SPI_CFG2_COMM GENMASK(18, 17)
-#define SPI_CFG2_SP_SHIFT 19
-#define SPI_CFG2_SP GENMASK(21, 19)
-#define SPI_CFG2_MASTER BIT(22)
-#define SPI_CFG2_LSBFRST BIT(23)
-#define SPI_CFG2_CPHA BIT(24)
-#define SPI_CFG2_CPOL BIT(25)
-#define SPI_CFG2_SSM BIT(26)
-#define SPI_CFG2_AFCNTR BIT(31)
+/* STM32F4_SPI_I2SCFGR bit fields */
+#define STM32F4_SPI_I2SCFGR_I2SMOD BIT(11)
-/* STM32_SPI_IER bit fields */
-#define SPI_IER_RXPIE BIT(0)
-#define SPI_IER_TXPIE BIT(1)
-#define SPI_IER_DXPIE BIT(2)
-#define SPI_IER_EOTIE BIT(3)
-#define SPI_IER_TXTFIE BIT(4)
-#define SPI_IER_OVRIE BIT(6)
-#define SPI_IER_MODFIE BIT(9)
-#define SPI_IER_ALL GENMASK(10, 0)
+/* STM32F4 SPI Baud Rate min/max divisor */
+#define STM32F4_SPI_BR_DIV_MIN (2 << STM32F4_SPI_CR1_BR_MIN)
+#define STM32F4_SPI_BR_DIV_MAX (2 << STM32F4_SPI_CR1_BR_MAX)
-/* STM32_SPI_SR bit fields */
-#define SPI_SR_RXP BIT(0)
-#define SPI_SR_TXP BIT(1)
-#define SPI_SR_EOT BIT(3)
-#define SPI_SR_OVR BIT(6)
-#define SPI_SR_MODF BIT(9)
-#define SPI_SR_SUSP BIT(11)
-#define SPI_SR_RXPLVL_SHIFT 13
-#define SPI_SR_RXPLVL GENMASK(14, 13)
-#define SPI_SR_RXWNE BIT(15)
+/* STM32H7 SPI registers */
+#define STM32H7_SPI_CR1 0x00
+#define STM32H7_SPI_CR2 0x04
+#define STM32H7_SPI_CFG1 0x08
+#define STM32H7_SPI_CFG2 0x0C
+#define STM32H7_SPI_IER 0x10
+#define STM32H7_SPI_SR 0x14
+#define STM32H7_SPI_IFCR 0x18
+#define STM32H7_SPI_TXDR 0x20
+#define STM32H7_SPI_RXDR 0x30
+#define STM32H7_SPI_I2SCFGR 0x50
-/* STM32_SPI_IFCR bit fields */
-#define SPI_IFCR_ALL GENMASK(11, 3)
+/* STM32H7_SPI_CR1 bit fields */
+#define STM32H7_SPI_CR1_SPE BIT(0)
+#define STM32H7_SPI_CR1_MASRX BIT(8)
+#define STM32H7_SPI_CR1_CSTART BIT(9)
+#define STM32H7_SPI_CR1_CSUSP BIT(10)
+#define STM32H7_SPI_CR1_HDDIR BIT(11)
+#define STM32H7_SPI_CR1_SSI BIT(12)
-/* STM32_SPI_I2SCFGR bit fields */
-#define SPI_I2SCFGR_I2SMOD BIT(0)
+/* STM32H7_SPI_CR2 bit fields */
+#define STM32H7_SPI_CR2_TSIZE_SHIFT 0
+#define STM32H7_SPI_CR2_TSIZE GENMASK(15, 0)
-/* SPI Master Baud Rate min/max divisor */
-#define SPI_MBR_DIV_MIN (2 << SPI_CFG1_MBR_MIN)
-#define SPI_MBR_DIV_MAX (2 << SPI_CFG1_MBR_MAX)
+/* STM32H7_SPI_CFG1 bit fields */
+#define STM32H7_SPI_CFG1_DSIZE_SHIFT 0
+#define STM32H7_SPI_CFG1_DSIZE GENMASK(4, 0)
+#define STM32H7_SPI_CFG1_FTHLV_SHIFT 5
+#define STM32H7_SPI_CFG1_FTHLV GENMASK(8, 5)
+#define STM32H7_SPI_CFG1_RXDMAEN BIT(14)
+#define STM32H7_SPI_CFG1_TXDMAEN BIT(15)
+#define STM32H7_SPI_CFG1_MBR_SHIFT 28
+#define STM32H7_SPI_CFG1_MBR GENMASK(30, 28)
+#define STM32H7_SPI_CFG1_MBR_MIN 0
+#define STM32H7_SPI_CFG1_MBR_MAX (GENMASK(30, 28) >> 28)
-/* SPI Communication mode */
+/* STM32H7_SPI_CFG2 bit fields */
+#define STM32H7_SPI_CFG2_MIDI_SHIFT 4
+#define STM32H7_SPI_CFG2_MIDI GENMASK(7, 4)
+#define STM32H7_SPI_CFG2_COMM_SHIFT 17
+#define STM32H7_SPI_CFG2_COMM GENMASK(18, 17)
+#define STM32H7_SPI_CFG2_SP_SHIFT 19
+#define STM32H7_SPI_CFG2_SP GENMASK(21, 19)
+#define STM32H7_SPI_CFG2_MASTER BIT(22)
+#define STM32H7_SPI_CFG2_LSBFRST BIT(23)
+#define STM32H7_SPI_CFG2_CPHA BIT(24)
+#define STM32H7_SPI_CFG2_CPOL BIT(25)
+#define STM32H7_SPI_CFG2_SSM BIT(26)
+#define STM32H7_SPI_CFG2_AFCNTR BIT(31)
+
+/* STM32H7_SPI_IER bit fields */
+#define STM32H7_SPI_IER_RXPIE BIT(0)
+#define STM32H7_SPI_IER_TXPIE BIT(1)
+#define STM32H7_SPI_IER_DXPIE BIT(2)
+#define STM32H7_SPI_IER_EOTIE BIT(3)
+#define STM32H7_SPI_IER_TXTFIE BIT(4)
+#define STM32H7_SPI_IER_OVRIE BIT(6)
+#define STM32H7_SPI_IER_MODFIE BIT(9)
+#define STM32H7_SPI_IER_ALL GENMASK(10, 0)
+
+/* STM32H7_SPI_SR bit fields */
+#define STM32H7_SPI_SR_RXP BIT(0)
+#define STM32H7_SPI_SR_TXP BIT(1)
+#define STM32H7_SPI_SR_EOT BIT(3)
+#define STM32H7_SPI_SR_OVR BIT(6)
+#define STM32H7_SPI_SR_MODF BIT(9)
+#define STM32H7_SPI_SR_SUSP BIT(11)
+#define STM32H7_SPI_SR_RXPLVL_SHIFT 13
+#define STM32H7_SPI_SR_RXPLVL GENMASK(14, 13)
+#define STM32H7_SPI_SR_RXWNE BIT(15)
+
+/* STM32H7_SPI_IFCR bit fields */
+#define STM32H7_SPI_IFCR_ALL GENMASK(11, 3)
+
+/* STM32H7_SPI_I2SCFGR bit fields */
+#define STM32H7_SPI_I2SCFGR_I2SMOD BIT(0)
+
+/* STM32H7 SPI Master Baud Rate min/max divisor */
+#define STM32H7_SPI_MBR_DIV_MIN (2 << STM32H7_SPI_CFG1_MBR_MIN)
+#define STM32H7_SPI_MBR_DIV_MAX (2 << STM32H7_SPI_CFG1_MBR_MAX)
+
+/* STM32H7 SPI Communication mode */
+#define STM32H7_SPI_FULL_DUPLEX 0
+#define STM32H7_SPI_SIMPLEX_TX 1
+#define STM32H7_SPI_SIMPLEX_RX 2
+#define STM32H7_SPI_HALF_DUPLEX 3
+
+/* SPI Communication type */
#define SPI_FULL_DUPLEX 0
#define SPI_SIMPLEX_TX 1
#define SPI_SIMPLEX_RX 2
-#define SPI_HALF_DUPLEX 3
+#define SPI_3WIRE_TX 3
+#define SPI_3WIRE_RX 4
#define SPI_1HZ_NS 1000000000
+/*
+ * use PIO for small transfers, avoiding DMA setup/teardown overhead for drivers
+ * without fifo buffers.
+ */
+#define SPI_DMA_MIN_BYTES 16
+
+/**
+ * stm32_spi_reg - stm32 SPI register & bitfield desc
+ * @reg: register offset
+ * @mask: bitfield mask
+ * @shift: left shift
+ */
+struct stm32_spi_reg {
+ int reg;
+ int mask;
+ int shift;
+};
+
+/**
+ * stm32_spi_regspec - stm32 registers definition, compatible dependent data
+ * en: enable register and SPI enable bit
+ * dma_rx_en: SPI DMA RX enable register end SPI DMA RX enable bit
+ * dma_tx_en: SPI DMA TX enable register end SPI DMA TX enable bit
+ * cpol: clock polarity register and polarity bit
+ * cpha: clock phase register and phase bit
+ * lsb_first: LSB transmitted first register and bit
+ * br: baud rate register and bitfields
+ * rx: SPI RX data register
+ * tx: SPI TX data register
+ */
+struct stm32_spi_regspec {
+ const struct stm32_spi_reg en;
+ const struct stm32_spi_reg dma_rx_en;
+ const struct stm32_spi_reg dma_tx_en;
+ const struct stm32_spi_reg cpol;
+ const struct stm32_spi_reg cpha;
+ const struct stm32_spi_reg lsb_first;
+ const struct stm32_spi_reg br;
+ const struct stm32_spi_reg rx;
+ const struct stm32_spi_reg tx;
+};
+
+struct stm32_spi;
+
+/**
+ * stm32_spi_cfg - stm32 compatible configuration data
+ * @regs: registers descriptions
+ * @get_fifo_size: routine to get fifo size
+ * @get_bpw_mask: routine to get bits per word mask
+ * @disable: routine to disable controller
+ * @config: routine to configure controller as SPI Master
+ * @set_bpw: routine to configure registers to for bits per word
+ * @set_mode: routine to configure registers to desired mode
+ * @set_data_idleness: optional routine to configure registers to desired idle
+ * time between frames (if driver has this functionality)
+ * set_number_of_data: optional routine to configure registers to desired
+ * number of data (if driver has this functionality)
+ * @can_dma: routine to determine if the transfer is eligible for DMA use
+ * @transfer_one_dma_start: routine to start transfer a single spi_transfer
+ * using DMA
+ * @dma_rx cb: routine to call after DMA RX channel operation is complete
+ * @dma_tx cb: routine to call after DMA TX channel operation is complete
+ * @transfer_one_irq: routine to configure interrupts for driver
+ * @irq_handler_event: Interrupt handler for SPI controller events
+ * @irq_handler_thread: thread of interrupt handler for SPI controller
+ * @baud_rate_div_min: minimum baud rate divisor
+ * @baud_rate_div_max: maximum baud rate divisor
+ * @has_fifo: boolean to know if fifo is used for driver
+ * @has_startbit: boolean to know if start bit is used to start transfer
+ */
+struct stm32_spi_cfg {
+ const struct stm32_spi_regspec *regs;
+ int (*get_fifo_size)(struct stm32_spi *spi);
+ int (*get_bpw_mask)(struct stm32_spi *spi);
+ void (*disable)(struct stm32_spi *spi);
+ int (*config)(struct stm32_spi *spi);
+ void (*set_bpw)(struct stm32_spi *spi);
+ int (*set_mode)(struct stm32_spi *spi, unsigned int comm_type);
+ void (*set_data_idleness)(struct stm32_spi *spi, u32 length);
+ int (*set_number_of_data)(struct stm32_spi *spi, u32 length);
+ void (*transfer_one_dma_start)(struct stm32_spi *spi);
+ void (*dma_rx_cb)(void *data);
+ void (*dma_tx_cb)(void *data);
+ int (*transfer_one_irq)(struct stm32_spi *spi);
+ irqreturn_t (*irq_handler_event)(int irq, void *dev_id);
+ irqreturn_t (*irq_handler_thread)(int irq, void *dev_id);
+ unsigned int baud_rate_div_min;
+ unsigned int baud_rate_div_max;
+ bool has_fifo;
+};
+
/**
* struct stm32_spi - private data of the SPI controller
* @dev: driver model representation of the controller
* @master: controller master interface
+ * @cfg: compatible configuration data
* @base: virtual memory area
* @clk: hw kernel clock feeding the SPI clock generator
* @clk_rate: rate of the hw kernel clock feeding the SPI clock generator
@@ -151,6 +290,7 @@
struct stm32_spi {
struct device *dev;
struct spi_master *master;
+ const struct stm32_spi_cfg *cfg;
void __iomem *base;
struct clk *clk;
u32 clk_rate;
@@ -176,6 +316,40 @@
dma_addr_t phys_addr;
};
+static const struct stm32_spi_regspec stm32f4_spi_regspec = {
+ .en = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_SPE },
+
+ .dma_rx_en = { STM32F4_SPI_CR2, STM32F4_SPI_CR2_RXDMAEN },
+ .dma_tx_en = { STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXDMAEN },
+
+ .cpol = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_CPOL },
+ .cpha = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_CPHA },
+ .lsb_first = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_LSBFRST },
+ .br = { STM32F4_SPI_CR1, STM32F4_SPI_CR1_BR, STM32F4_SPI_CR1_BR_SHIFT },
+
+ .rx = { STM32F4_SPI_DR },
+ .tx = { STM32F4_SPI_DR },
+};
+
+static const struct stm32_spi_regspec stm32h7_spi_regspec = {
+ /* SPI data transfer is enabled but spi_ker_ck is idle.
+ * CFG1 and CFG2 registers are write protected when SPE is enabled.
+ */
+ .en = { STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE },
+
+ .dma_rx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_RXDMAEN },
+ .dma_tx_en = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN },
+
+ .cpol = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPOL },
+ .cpha = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_CPHA },
+ .lsb_first = { STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_LSBFRST },
+ .br = { STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_MBR,
+ STM32H7_SPI_CFG1_MBR_SHIFT },
+
+ .rx = { STM32H7_SPI_RXDR },
+ .tx = { STM32H7_SPI_TXDR },
+};
+
static inline void stm32_spi_set_bits(struct stm32_spi *spi,
u32 offset, u32 bits)
{
@@ -191,22 +365,22 @@
}
/**
- * stm32_spi_get_fifo_size - Return fifo size
+ * stm32h7_spi_get_fifo_size - Return fifo size
* @spi: pointer to the spi controller data structure
*/
-static int stm32_spi_get_fifo_size(struct stm32_spi *spi)
+static int stm32h7_spi_get_fifo_size(struct stm32_spi *spi)
{
unsigned long flags;
u32 count = 0;
spin_lock_irqsave(&spi->lock, flags);
- stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+ stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);
- while (readl_relaxed(spi->base + STM32_SPI_SR) & SPI_SR_TXP)
- writeb_relaxed(++count, spi->base + STM32_SPI_TXDR);
+ while (readl_relaxed(spi->base + STM32H7_SPI_SR) & STM32H7_SPI_SR_TXP)
+ writeb_relaxed(++count, spi->base + STM32H7_SPI_TXDR);
- stm32_spi_clr_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+ stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);
spin_unlock_irqrestore(&spi->lock, flags);
@@ -216,10 +390,20 @@
}
/**
- * stm32_spi_get_bpw_mask - Return bits per word mask
+ * stm32f4_spi_get_bpw_mask - Return bits per word mask
* @spi: pointer to the spi controller data structure
*/
-static int stm32_spi_get_bpw_mask(struct stm32_spi *spi)
+static int stm32f4_spi_get_bpw_mask(struct stm32_spi *spi)
+{
+ dev_dbg(spi->dev, "8-bit or 16-bit data frame supported\n");
+ return SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
+}
+
+/**
+ * stm32h7_spi_get_bpw_mask - Return bits per word mask
+ * @spi: pointer to the spi controller data structure
+ */
+static int stm32h7_spi_get_bpw_mask(struct stm32_spi *spi)
{
unsigned long flags;
u32 cfg1, max_bpw;
@@ -230,10 +414,11 @@
* The most significant bit at DSIZE bit field is reserved when the
* maximum data size of periperal instances is limited to 16-bit
*/
- stm32_spi_set_bits(spi, STM32_SPI_CFG1, SPI_CFG1_DSIZE);
+ stm32_spi_set_bits(spi, STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_DSIZE);
- cfg1 = readl_relaxed(spi->base + STM32_SPI_CFG1);
- max_bpw = (cfg1 & SPI_CFG1_DSIZE) >> SPI_CFG1_DSIZE_SHIFT;
+ cfg1 = readl_relaxed(spi->base + STM32H7_SPI_CFG1);
+ max_bpw = (cfg1 & STM32H7_SPI_CFG1_DSIZE) >>
+ STM32H7_SPI_CFG1_DSIZE_SHIFT;
max_bpw += 1;
spin_unlock_irqrestore(&spi->lock, flags);
@@ -244,13 +429,16 @@
}
/**
- * stm32_spi_prepare_mbr - Determine SPI_CFG1.MBR value
+ * stm32_spi_prepare_mbr - Determine baud rate divisor value
* @spi: pointer to the spi controller data structure
* @speed_hz: requested speed
+ * @min_div: minimum baud rate divisor
+ * @max_div: maximum baud rate divisor
*
- * Return SPI_CFG1.MBR value in case of success or -EINVAL
+ * Return baud rate divisor value in case of success or -EINVAL
*/
-static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz)
+static int stm32_spi_prepare_mbr(struct stm32_spi *spi, u32 speed_hz,
+ u32 min_div, u32 max_div)
{
u32 div, mbrdiv;
@@ -263,8 +451,7 @@
* no need to check it there.
* However, we need to ensure the following calculations.
*/
- if (div < SPI_MBR_DIV_MIN ||
- div > SPI_MBR_DIV_MAX)
+ if ((div < min_div) || (div > max_div))
return -EINVAL;
/* Determine the first power of 2 greater than or equal to div */
@@ -279,10 +466,10 @@
}
/**
- * stm32_spi_prepare_fthlv - Determine FIFO threshold level
+ * stm32h7_spi_prepare_fthlv - Determine FIFO threshold level
* @spi: pointer to the spi controller data structure
*/
-static u32 stm32_spi_prepare_fthlv(struct stm32_spi *spi)
+static u32 stm32h7_spi_prepare_fthlv(struct stm32_spi *spi)
{
u32 fthlv, half_fifo;
@@ -306,32 +493,27 @@
}
/**
- * stm32_spi_write_txfifo - Write bytes in Transmit Data Register
+ * stm32f4_spi_write_tx - Write bytes to Transmit Data Register
* @spi: pointer to the spi controller data structure
*
* Read from tx_buf depends on remaining bytes to avoid to read beyond
* tx_buf end.
*/
-static void stm32_spi_write_txfifo(struct stm32_spi *spi)
+static void stm32f4_spi_write_tx(struct stm32_spi *spi)
{
- while ((spi->tx_len > 0) &&
- (readl_relaxed(spi->base + STM32_SPI_SR) & SPI_SR_TXP)) {
+ if ((spi->tx_len > 0) && (readl_relaxed(spi->base + STM32F4_SPI_SR) &
+ STM32F4_SPI_SR_TXE)) {
u32 offs = spi->cur_xferlen - spi->tx_len;
- if (spi->tx_len >= sizeof(u32)) {
- const u32 *tx_buf32 = (const u32 *)(spi->tx_buf + offs);
-
- writel_relaxed(*tx_buf32, spi->base + STM32_SPI_TXDR);
- spi->tx_len -= sizeof(u32);
- } else if (spi->tx_len >= sizeof(u16)) {
+ if (spi->cur_bpw == 16) {
const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);
- writew_relaxed(*tx_buf16, spi->base + STM32_SPI_TXDR);
+ writew_relaxed(*tx_buf16, spi->base + STM32F4_SPI_DR);
spi->tx_len -= sizeof(u16);
} else {
const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);
- writeb_relaxed(*tx_buf8, spi->base + STM32_SPI_TXDR);
+ writeb_relaxed(*tx_buf8, spi->base + STM32F4_SPI_DR);
spi->tx_len -= sizeof(u8);
}
}
@@ -340,43 +522,109 @@
}
/**
- * stm32_spi_read_rxfifo - Read bytes in Receive Data Register
+ * stm32h7_spi_write_txfifo - Write bytes in Transmit Data Register
+ * @spi: pointer to the spi controller data structure
+ *
+ * Read from tx_buf depends on remaining bytes to avoid to read beyond
+ * tx_buf end.
+ */
+static void stm32h7_spi_write_txfifo(struct stm32_spi *spi)
+{
+ while ((spi->tx_len > 0) &&
+ (readl_relaxed(spi->base + STM32H7_SPI_SR) &
+ STM32H7_SPI_SR_TXP)) {
+ u32 offs = spi->cur_xferlen - spi->tx_len;
+
+ if (spi->tx_len >= sizeof(u32)) {
+ const u32 *tx_buf32 = (const u32 *)(spi->tx_buf + offs);
+
+ writel_relaxed(*tx_buf32, spi->base + STM32H7_SPI_TXDR);
+ spi->tx_len -= sizeof(u32);
+ } else if (spi->tx_len >= sizeof(u16)) {
+ const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);
+
+ writew_relaxed(*tx_buf16, spi->base + STM32H7_SPI_TXDR);
+ spi->tx_len -= sizeof(u16);
+ } else {
+ const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);
+
+ writeb_relaxed(*tx_buf8, spi->base + STM32H7_SPI_TXDR);
+ spi->tx_len -= sizeof(u8);
+ }
+ }
+
+ dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->tx_len);
+}
+
+/**
+ * stm32f4_spi_read_rx - Read bytes from Receive Data Register
* @spi: pointer to the spi controller data structure
*
* Write in rx_buf depends on remaining bytes to avoid to write beyond
* rx_buf end.
*/
-static void stm32_spi_read_rxfifo(struct stm32_spi *spi, bool flush)
+static void stm32f4_spi_read_rx(struct stm32_spi *spi)
{
- u32 sr = readl_relaxed(spi->base + STM32_SPI_SR);
- u32 rxplvl = (sr & SPI_SR_RXPLVL) >> SPI_SR_RXPLVL_SHIFT;
+ if ((spi->rx_len > 0) && (readl_relaxed(spi->base + STM32F4_SPI_SR) &
+ STM32F4_SPI_SR_RXNE)) {
+ u32 offs = spi->cur_xferlen - spi->rx_len;
+
+ if (spi->cur_bpw == 16) {
+ u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);
+
+ *rx_buf16 = readw_relaxed(spi->base + STM32F4_SPI_DR);
+ spi->rx_len -= sizeof(u16);
+ } else {
+ u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);
+
+ *rx_buf8 = readb_relaxed(spi->base + STM32F4_SPI_DR);
+ spi->rx_len -= sizeof(u8);
+ }
+ }
+
+ dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->rx_len);
+}
+
+/**
+ * stm32h7_spi_read_rxfifo - Read bytes in Receive Data Register
+ * @spi: pointer to the spi controller data structure
+ *
+ * Write in rx_buf depends on remaining bytes to avoid to write beyond
+ * rx_buf end.
+ */
+static void stm32h7_spi_read_rxfifo(struct stm32_spi *spi, bool flush)
+{
+ u32 sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
+ u32 rxplvl = (sr & STM32H7_SPI_SR_RXPLVL) >>
+ STM32H7_SPI_SR_RXPLVL_SHIFT;
while ((spi->rx_len > 0) &&
- ((sr & SPI_SR_RXP) ||
- (flush && ((sr & SPI_SR_RXWNE) || (rxplvl > 0))))) {
+ ((sr & STM32H7_SPI_SR_RXP) ||
+ (flush && ((sr & STM32H7_SPI_SR_RXWNE) || (rxplvl > 0))))) {
u32 offs = spi->cur_xferlen - spi->rx_len;
if ((spi->rx_len >= sizeof(u32)) ||
- (flush && (sr & SPI_SR_RXWNE))) {
+ (flush && (sr & STM32H7_SPI_SR_RXWNE))) {
u32 *rx_buf32 = (u32 *)(spi->rx_buf + offs);
- *rx_buf32 = readl_relaxed(spi->base + STM32_SPI_RXDR);
+ *rx_buf32 = readl_relaxed(spi->base + STM32H7_SPI_RXDR);
spi->rx_len -= sizeof(u32);
} else if ((spi->rx_len >= sizeof(u16)) ||
(flush && (rxplvl >= 2 || spi->cur_bpw > 8))) {
u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);
- *rx_buf16 = readw_relaxed(spi->base + STM32_SPI_RXDR);
+ *rx_buf16 = readw_relaxed(spi->base + STM32H7_SPI_RXDR);
spi->rx_len -= sizeof(u16);
} else {
u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);
- *rx_buf8 = readb_relaxed(spi->base + STM32_SPI_RXDR);
+ *rx_buf8 = readb_relaxed(spi->base + STM32H7_SPI_RXDR);
spi->rx_len -= sizeof(u8);
}
- sr = readl_relaxed(spi->base + STM32_SPI_SR);
- rxplvl = (sr & SPI_SR_RXPLVL) >> SPI_SR_RXPLVL_SHIFT;
+ sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
+ rxplvl = (sr & STM32H7_SPI_SR_RXPLVL) >>
+ STM32H7_SPI_SR_RXPLVL_SHIFT;
}
dev_dbg(spi->dev, "%s%s: %d bytes left\n", __func__,
@@ -386,26 +634,76 @@
/**
* stm32_spi_enable - Enable SPI controller
* @spi: pointer to the spi controller data structure
- *
- * SPI data transfer is enabled but spi_ker_ck is idle.
- * SPI_CFG1 and SPI_CFG2 are now write protected.
*/
static void stm32_spi_enable(struct stm32_spi *spi)
{
dev_dbg(spi->dev, "enable controller\n");
- stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+ stm32_spi_set_bits(spi, spi->cfg->regs->en.reg,
+ spi->cfg->regs->en.mask);
}
/**
- * stm32_spi_disable - Disable SPI controller
+ * stm32f4_spi_disable - Disable SPI controller
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32f4_spi_disable(struct stm32_spi *spi)
+{
+ unsigned long flags;
+ u32 sr;
+
+ dev_dbg(spi->dev, "disable controller\n");
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ if (!(readl_relaxed(spi->base + STM32F4_SPI_CR1) &
+ STM32F4_SPI_CR1_SPE)) {
+ spin_unlock_irqrestore(&spi->lock, flags);
+ return;
+ }
+
+ /* Disable interrupts */
+ stm32_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXEIE |
+ STM32F4_SPI_CR2_RXNEIE |
+ STM32F4_SPI_CR2_ERRIE);
+
+ /* Wait until BSY = 0 */
+ if (readl_relaxed_poll_timeout_atomic(spi->base + STM32F4_SPI_SR,
+ sr, !(sr & STM32F4_SPI_SR_BSY),
+ 10, 100000) < 0) {
+ dev_warn(spi->dev, "disabling condition timeout\n");
+ }
+
+ if (spi->cur_usedma && spi->dma_tx)
+ dmaengine_terminate_all(spi->dma_tx);
+ if (spi->cur_usedma && spi->dma_rx)
+ dmaengine_terminate_all(spi->dma_rx);
+
+ stm32_spi_clr_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SPE);
+
+ stm32_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXDMAEN |
+ STM32F4_SPI_CR2_RXDMAEN);
+
+ /* Sequence to clear OVR flag */
+ readl_relaxed(spi->base + STM32F4_SPI_DR);
+ readl_relaxed(spi->base + STM32F4_SPI_SR);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+}
+
+/**
+ * stm32h7_spi_disable - Disable SPI controller
* @spi: pointer to the spi controller data structure
*
* RX-Fifo is flushed when SPI controller is disabled. To prevent any data
- * loss, use stm32_spi_read_rxfifo(flush) to read the remaining bytes in
+ * loss, use stm32h7_spi_read_rxfifo(flush) to read the remaining bytes in
* RX-Fifo.
+ * Normally, if TSIZE has been configured, we should relax the hardware at the
+ * reception of the EOT interrupt. But in case of error, EOT will not be
+ * raised. So the subsystem unprepare_message call allows us to properly
+ * complete the transfer from an hardware point of view.
*/
-static void stm32_spi_disable(struct stm32_spi *spi)
+static void stm32h7_spi_disable(struct stm32_spi *spi)
{
unsigned long flags;
u32 cr1, sr;
@@ -414,23 +712,23 @@
spin_lock_irqsave(&spi->lock, flags);
- cr1 = readl_relaxed(spi->base + STM32_SPI_CR1);
+ cr1 = readl_relaxed(spi->base + STM32H7_SPI_CR1);
- if (!(cr1 & SPI_CR1_SPE)) {
+ if (!(cr1 & STM32H7_SPI_CR1_SPE)) {
spin_unlock_irqrestore(&spi->lock, flags);
return;
}
/* Wait on EOT or suspend the flow */
- if (readl_relaxed_poll_timeout_atomic(spi->base + STM32_SPI_SR,
- sr, !(sr & SPI_SR_EOT),
+ if (readl_relaxed_poll_timeout_atomic(spi->base + STM32H7_SPI_SR,
+ sr, !(sr & STM32H7_SPI_SR_EOT),
10, 100000) < 0) {
- if (cr1 & SPI_CR1_CSTART) {
- writel_relaxed(cr1 | SPI_CR1_CSUSP,
- spi->base + STM32_SPI_CR1);
+ if (cr1 & STM32H7_SPI_CR1_CSTART) {
+ writel_relaxed(cr1 | STM32H7_SPI_CR1_CSUSP,
+ spi->base + STM32H7_SPI_CR1);
if (readl_relaxed_poll_timeout_atomic(
- spi->base + STM32_SPI_SR,
- sr, !(sr & SPI_SR_SUSP),
+ spi->base + STM32H7_SPI_SR,
+ sr, !(sr & STM32H7_SPI_SR_SUSP),
10, 100000) < 0)
dev_warn(spi->dev,
"Suspend request timeout\n");
@@ -438,21 +736,21 @@
}
if (!spi->cur_usedma && spi->rx_buf && (spi->rx_len > 0))
- stm32_spi_read_rxfifo(spi, true);
+ stm32h7_spi_read_rxfifo(spi, true);
- if (spi->cur_usedma && spi->tx_buf)
+ if (spi->cur_usedma && spi->dma_tx)
dmaengine_terminate_all(spi->dma_tx);
- if (spi->cur_usedma && spi->rx_buf)
+ if (spi->cur_usedma && spi->dma_rx)
dmaengine_terminate_all(spi->dma_rx);
- stm32_spi_clr_bits(spi, STM32_SPI_CR1, SPI_CR1_SPE);
+ stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SPE);
- stm32_spi_clr_bits(spi, STM32_SPI_CFG1, SPI_CFG1_TXDMAEN |
- SPI_CFG1_RXDMAEN);
+ stm32_spi_clr_bits(spi, STM32H7_SPI_CFG1, STM32H7_SPI_CFG1_TXDMAEN |
+ STM32H7_SPI_CFG1_RXDMAEN);
/* Disable interrupts and clear status flags */
- writel_relaxed(0, spi->base + STM32_SPI_IER);
- writel_relaxed(SPI_IFCR_ALL, spi->base + STM32_SPI_IFCR);
+ writel_relaxed(0, spi->base + STM32H7_SPI_IER);
+ writel_relaxed(STM32H7_SPI_IFCR_ALL, spi->base + STM32H7_SPI_IFCR);
spin_unlock_irqrestore(&spi->lock, flags);
}
@@ -460,26 +758,136 @@
/**
* stm32_spi_can_dma - Determine if the transfer is eligible for DMA use
*
- * If the current transfer size is greater than fifo size, use DMA.
+ * If driver has fifo and the current transfer size is greater than fifo size,
+ * use DMA. Otherwise use DMA for transfer longer than defined DMA min bytes.
*/
static bool stm32_spi_can_dma(struct spi_master *master,
struct spi_device *spi_dev,
struct spi_transfer *transfer)
{
+ unsigned int dma_size;
struct stm32_spi *spi = spi_master_get_devdata(master);
- dev_dbg(spi->dev, "%s: %s\n", __func__,
- (transfer->len > spi->fifo_size) ? "true" : "false");
+ if (spi->cfg->has_fifo)
+ dma_size = spi->fifo_size;
+ else
+ dma_size = SPI_DMA_MIN_BYTES;
- return (transfer->len > spi->fifo_size);
+ dev_dbg(spi->dev, "%s: %s\n", __func__,
+ (transfer->len > dma_size) ? "true" : "false");
+
+ return (transfer->len > dma_size);
}
/**
- * stm32_spi_irq - Interrupt handler for SPI controller events
+ * stm32f4_spi_irq_event - Interrupt handler for SPI controller events
* @irq: interrupt line
* @dev_id: SPI controller master interface
*/
-static irqreturn_t stm32_spi_irq(int irq, void *dev_id)
+static irqreturn_t stm32f4_spi_irq_event(int irq, void *dev_id)
+{
+ struct spi_master *master = dev_id;
+ struct stm32_spi *spi = spi_master_get_devdata(master);
+ u32 sr, mask = 0;
+ unsigned long flags;
+ bool end = false;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ sr = readl_relaxed(spi->base + STM32F4_SPI_SR);
+ /*
+ * BSY flag is not handled in interrupt but it is normal behavior when
+ * this flag is set.
+ */
+ sr &= ~STM32F4_SPI_SR_BSY;
+
+ if (!spi->cur_usedma && (spi->cur_comm == SPI_SIMPLEX_TX ||
+ spi->cur_comm == SPI_3WIRE_TX)) {
+ /* OVR flag shouldn't be handled for TX only mode */
+ sr &= ~STM32F4_SPI_SR_OVR | STM32F4_SPI_SR_RXNE;
+ mask |= STM32F4_SPI_SR_TXE;
+ }
+
+ if (!spi->cur_usedma && spi->cur_comm == SPI_FULL_DUPLEX) {
+ /* TXE flag is set and is handled when RXNE flag occurs */
+ sr &= ~STM32F4_SPI_SR_TXE;
+ mask |= STM32F4_SPI_SR_RXNE | STM32F4_SPI_SR_OVR;
+ }
+
+ if (!(sr & mask)) {
+ dev_dbg(spi->dev, "spurious IT (sr=0x%08x)\n", sr);
+ spin_unlock_irqrestore(&spi->lock, flags);
+ return IRQ_NONE;
+ }
+
+ if (sr & STM32F4_SPI_SR_OVR) {
+ dev_warn(spi->dev, "Overrun: received value discarded\n");
+
+ /* Sequence to clear OVR flag */
+ readl_relaxed(spi->base + STM32F4_SPI_DR);
+ readl_relaxed(spi->base + STM32F4_SPI_SR);
+
+ /*
+ * If overrun is detected, it means that something went wrong,
+ * so stop the current transfer. Transfer can wait for next
+ * RXNE but DR is already read and end never happens.
+ */
+ end = true;
+ goto end_irq;
+ }
+
+ if (sr & STM32F4_SPI_SR_TXE) {
+ if (spi->tx_buf)
+ stm32f4_spi_write_tx(spi);
+ if (spi->tx_len == 0)
+ end = true;
+ }
+
+ if (sr & STM32F4_SPI_SR_RXNE) {
+ stm32f4_spi_read_rx(spi);
+ if (spi->rx_len == 0)
+ end = true;
+ else /* Load data for discontinuous mode */
+ stm32f4_spi_write_tx(spi);
+ }
+
+end_irq:
+ if (end) {
+ /* Immediately disable interrupts to do not generate new one */
+ stm32_spi_clr_bits(spi, STM32F4_SPI_CR2,
+ STM32F4_SPI_CR2_TXEIE |
+ STM32F4_SPI_CR2_RXNEIE |
+ STM32F4_SPI_CR2_ERRIE);
+ spin_unlock_irqrestore(&spi->lock, flags);
+ return IRQ_WAKE_THREAD;
+ }
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+ return IRQ_HANDLED;
+}
+
+/**
+ * stm32f4_spi_irq_thread - Thread of interrupt handler for SPI controller
+ * @irq: interrupt line
+ * @dev_id: SPI controller master interface
+ */
+static irqreturn_t stm32f4_spi_irq_thread(int irq, void *dev_id)
+{
+ struct spi_master *master = dev_id;
+ struct stm32_spi *spi = spi_master_get_devdata(master);
+
+ spi_finalize_current_transfer(master);
+ stm32f4_spi_disable(spi);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * stm32h7_spi_irq_thread - Thread of interrupt handler for SPI controller
+ * @irq: interrupt line
+ * @dev_id: SPI controller master interface
+ */
+static irqreturn_t stm32h7_spi_irq_thread(int irq, void *dev_id)
{
struct spi_master *master = dev_id;
struct stm32_spi *spi = spi_master_get_devdata(master);
@@ -489,19 +897,19 @@
spin_lock_irqsave(&spi->lock, flags);
- sr = readl_relaxed(spi->base + STM32_SPI_SR);
- ier = readl_relaxed(spi->base + STM32_SPI_IER);
+ sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
+ ier = readl_relaxed(spi->base + STM32H7_SPI_IER);
mask = ier;
/* EOTIE is triggered on EOT, SUSP and TXC events. */
- mask |= SPI_SR_SUSP;
+ mask |= STM32H7_SPI_SR_SUSP;
/*
* When TXTF is set, DXPIE and TXPIE are cleared. So in case of
* Full-Duplex, need to poll RXP event to know if there are remaining
* data, before disabling SPI.
*/
if (spi->rx_buf && !spi->cur_usedma)
- mask |= SPI_SR_RXP;
+ mask |= STM32H7_SPI_SR_RXP;
if (!(sr & mask)) {
dev_dbg(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
@@ -510,10 +918,10 @@
return IRQ_NONE;
}
- if (sr & SPI_SR_SUSP) {
+ if (sr & STM32H7_SPI_SR_SUSP) {
dev_warn(spi->dev, "Communication suspended\n");
if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
- stm32_spi_read_rxfifo(spi, false);
+ stm32h7_spi_read_rxfifo(spi, false);
/*
* If communication is suspended while using DMA, it means
* that something went wrong, so stop the current transfer
@@ -522,15 +930,15 @@
end = true;
}
- if (sr & SPI_SR_MODF) {
+ if (sr & STM32H7_SPI_SR_MODF) {
dev_warn(spi->dev, "Mode fault: transfer aborted\n");
end = true;
}
- if (sr & SPI_SR_OVR) {
+ if (sr & STM32H7_SPI_SR_OVR) {
dev_warn(spi->dev, "Overrun: received value discarded\n");
if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
- stm32_spi_read_rxfifo(spi, false);
+ stm32h7_spi_read_rxfifo(spi, false);
/*
* If overrun is detected while using DMA, it means that
* something went wrong, so stop the current transfer
@@ -539,27 +947,27 @@
end = true;
}
- if (sr & SPI_SR_EOT) {
+ if (sr & STM32H7_SPI_SR_EOT) {
if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
- stm32_spi_read_rxfifo(spi, true);
+ stm32h7_spi_read_rxfifo(spi, true);
end = true;
}
- if (sr & SPI_SR_TXP)
+ if (sr & STM32H7_SPI_SR_TXP)
if (!spi->cur_usedma && (spi->tx_buf && (spi->tx_len > 0)))
- stm32_spi_write_txfifo(spi);
+ stm32h7_spi_write_txfifo(spi);
- if (sr & SPI_SR_RXP)
+ if (sr & STM32H7_SPI_SR_RXP)
if (!spi->cur_usedma && (spi->rx_buf && (spi->rx_len > 0)))
- stm32_spi_read_rxfifo(spi, false);
+ stm32h7_spi_read_rxfifo(spi, false);
- writel_relaxed(mask, spi->base + STM32_SPI_IFCR);
+ writel_relaxed(mask, spi->base + STM32H7_SPI_IFCR);
spin_unlock_irqrestore(&spi->lock, flags);
if (end) {
spi_finalize_current_transfer(master);
- stm32_spi_disable(spi);
+ stm32h7_spi_disable(spi);
}
return IRQ_HANDLED;
@@ -598,7 +1006,7 @@
struct spi_device *spi_dev = msg->spi;
struct device_node *np = spi_dev->dev.of_node;
unsigned long flags;
- u32 cfg2_clrb = 0, cfg2_setb = 0;
+ u32 clrb = 0, setb = 0;
/* SPI slave device may need time between data frames */
spi->cur_midi = 0;
@@ -606,19 +1014,19 @@
dev_dbg(spi->dev, "%dns inter-data idleness\n", spi->cur_midi);
if (spi_dev->mode & SPI_CPOL)
- cfg2_setb |= SPI_CFG2_CPOL;
+ setb |= spi->cfg->regs->cpol.mask;
else
- cfg2_clrb |= SPI_CFG2_CPOL;
+ clrb |= spi->cfg->regs->cpol.mask;
if (spi_dev->mode & SPI_CPHA)
- cfg2_setb |= SPI_CFG2_CPHA;
+ setb |= spi->cfg->regs->cpha.mask;
else
- cfg2_clrb |= SPI_CFG2_CPHA;
+ clrb |= spi->cfg->regs->cpha.mask;
if (spi_dev->mode & SPI_LSB_FIRST)
- cfg2_setb |= SPI_CFG2_LSBFRST;
+ setb |= spi->cfg->regs->lsb_first.mask;
else
- cfg2_clrb |= SPI_CFG2_LSBFRST;
+ clrb |= spi->cfg->regs->lsb_first.mask;
dev_dbg(spi->dev, "cpol=%d cpha=%d lsb_first=%d cs_high=%d\n",
spi_dev->mode & SPI_CPOL,
@@ -628,11 +1036,12 @@
spin_lock_irqsave(&spi->lock, flags);
- if (cfg2_clrb || cfg2_setb)
+ /* CPOL, CPHA and LSB FIRST bits have common register */
+ if (clrb || setb)
writel_relaxed(
- (readl_relaxed(spi->base + STM32_SPI_CFG2) &
- ~cfg2_clrb) | cfg2_setb,
- spi->base + STM32_SPI_CFG2);
+ (readl_relaxed(spi->base + spi->cfg->regs->cpol.reg) &
+ ~clrb) | setb,
+ spi->base + spi->cfg->regs->cpol.reg);
spin_unlock_irqrestore(&spi->lock, flags);
@@ -640,12 +1049,40 @@
}
/**
- * stm32_spi_dma_cb - dma callback
+ * stm32f4_spi_dma_tx_cb - dma callback
+ *
+ * DMA callback is called when the transfer is complete for DMA TX channel.
+ */
+static void stm32f4_spi_dma_tx_cb(void *data)
+{
+ struct stm32_spi *spi = data;
+
+ if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
+ spi_finalize_current_transfer(spi->master);
+ stm32f4_spi_disable(spi);
+ }
+}
+
+/**
+ * stm32f4_spi_dma_rx_cb - dma callback
+ *
+ * DMA callback is called when the transfer is complete for DMA RX channel.
+ */
+static void stm32f4_spi_dma_rx_cb(void *data)
+{
+ struct stm32_spi *spi = data;
+
+ spi_finalize_current_transfer(spi->master);
+ stm32f4_spi_disable(spi);
+}
+
+/**
+ * stm32h7_spi_dma_cb - dma callback
*
* DMA callback is called when the transfer is complete or when an error
* occurs. If the transfer is complete, EOT flag is raised.
*/
-static void stm32_spi_dma_cb(void *data)
+static void stm32h7_spi_dma_cb(void *data)
{
struct stm32_spi *spi = data;
unsigned long flags;
@@ -653,11 +1090,11 @@
spin_lock_irqsave(&spi->lock, flags);
- sr = readl_relaxed(spi->base + STM32_SPI_SR);
+ sr = readl_relaxed(spi->base + STM32H7_SPI_SR);
spin_unlock_irqrestore(&spi->lock, flags);
- if (!(sr & SPI_SR_EOT))
+ if (!(sr & STM32H7_SPI_SR_EOT))
dev_warn(spi->dev, "DMA error (sr=0x%08x)\n", sr);
/* Now wait for EOT, or SUSP or OVR in case of error */
@@ -681,23 +1118,27 @@
else
buswidth = DMA_SLAVE_BUSWIDTH_4_BYTES;
- /* Valid for DMA Half or Full Fifo threshold */
- if (spi->cur_fthlv == 2)
+ if (spi->cfg->has_fifo) {
+ /* Valid for DMA Half or Full Fifo threshold */
+ if (spi->cur_fthlv == 2)
+ maxburst = 1;
+ else
+ maxburst = spi->cur_fthlv;
+ } else {
maxburst = 1;
- else
- maxburst = spi->cur_fthlv;
+ }
memset(dma_conf, 0, sizeof(struct dma_slave_config));
dma_conf->direction = dir;
if (dma_conf->direction == DMA_DEV_TO_MEM) { /* RX */
- dma_conf->src_addr = spi->phys_addr + STM32_SPI_RXDR;
+ dma_conf->src_addr = spi->phys_addr + spi->cfg->regs->rx.reg;
dma_conf->src_addr_width = buswidth;
dma_conf->src_maxburst = maxburst;
dev_dbg(spi->dev, "Rx DMA config buswidth=%d, maxburst=%d\n",
buswidth, maxburst);
} else if (dma_conf->direction == DMA_MEM_TO_DEV) { /* TX */
- dma_conf->dst_addr = spi->phys_addr + STM32_SPI_TXDR;
+ dma_conf->dst_addr = spi->phys_addr + spi->cfg->regs->tx.reg;
dma_conf->dst_addr_width = buswidth;
dma_conf->dst_maxburst = maxburst;
@@ -707,27 +1148,68 @@
}
/**
- * stm32_spi_transfer_one_irq - transfer a single spi_transfer using
- * interrupts
+ * stm32f4_spi_transfer_one_irq - transfer a single spi_transfer using
+ * interrupts
*
* It must returns 0 if the transfer is finished or 1 if the transfer is still
* in progress.
*/
-static int stm32_spi_transfer_one_irq(struct stm32_spi *spi)
+static int stm32f4_spi_transfer_one_irq(struct stm32_spi *spi)
+{
+ unsigned long flags;
+ u32 cr2 = 0;
+
+ /* Enable the interrupts relative to the current communication mode */
+ if (spi->cur_comm == SPI_SIMPLEX_TX || spi->cur_comm == SPI_3WIRE_TX) {
+ cr2 |= STM32F4_SPI_CR2_TXEIE;
+ } else if (spi->cur_comm == SPI_FULL_DUPLEX) {
+ /* In transmit-only mode, the OVR flag is set in the SR register
+ * since the received data are never read. Therefore set OVR
+ * interrupt only when rx buffer is available.
+ */
+ cr2 |= STM32F4_SPI_CR2_RXNEIE | STM32F4_SPI_CR2_ERRIE;
+ } else {
+ return -EINVAL;
+ }
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ stm32_spi_set_bits(spi, STM32F4_SPI_CR2, cr2);
+
+ stm32_spi_enable(spi);
+
+ /* starting data transfer when buffer is loaded */
+ if (spi->tx_buf)
+ stm32f4_spi_write_tx(spi);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return 1;
+}
+
+/**
+ * stm32h7_spi_transfer_one_irq - transfer a single spi_transfer using
+ * interrupts
+ *
+ * It must returns 0 if the transfer is finished or 1 if the transfer is still
+ * in progress.
+ */
+static int stm32h7_spi_transfer_one_irq(struct stm32_spi *spi)
{
unsigned long flags;
u32 ier = 0;
/* Enable the interrupts relative to the current communication mode */
if (spi->tx_buf && spi->rx_buf) /* Full Duplex */
- ier |= SPI_IER_DXPIE;
+ ier |= STM32H7_SPI_IER_DXPIE;
else if (spi->tx_buf) /* Half-Duplex TX dir or Simplex TX */
- ier |= SPI_IER_TXPIE;
+ ier |= STM32H7_SPI_IER_TXPIE;
else if (spi->rx_buf) /* Half-Duplex RX dir or Simplex RX */
- ier |= SPI_IER_RXPIE;
+ ier |= STM32H7_SPI_IER_RXPIE;
/* Enable the interrupts relative to the end of transfer */
- ier |= SPI_IER_EOTIE | SPI_IER_TXTFIE | SPI_IER_OVRIE | SPI_IER_MODFIE;
+ ier |= STM32H7_SPI_IER_EOTIE | STM32H7_SPI_IER_TXTFIE |
+ STM32H7_SPI_IER_OVRIE | STM32H7_SPI_IER_MODFIE;
spin_lock_irqsave(&spi->lock, flags);
@@ -735,11 +1217,11 @@
/* Be sure to have data in fifo before starting data transfer */
if (spi->tx_buf)
- stm32_spi_write_txfifo(spi);
+ stm32h7_spi_write_txfifo(spi);
- stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_CSTART);
+ stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);
- writel_relaxed(ier, spi->base + STM32_SPI_IER);
+ writel_relaxed(ier, spi->base + STM32H7_SPI_IER);
spin_unlock_irqrestore(&spi->lock, flags);
@@ -747,6 +1229,43 @@
}
/**
+ * stm32f4_spi_transfer_one_dma_start - Set SPI driver registers to start
+ * transfer using DMA
+ */
+static void stm32f4_spi_transfer_one_dma_start(struct stm32_spi *spi)
+{
+ /* In DMA mode end of transfer is handled by DMA TX or RX callback. */
+ if (spi->cur_comm == SPI_SIMPLEX_RX || spi->cur_comm == SPI_3WIRE_RX ||
+ spi->cur_comm == SPI_FULL_DUPLEX) {
+ /*
+ * In transmit-only mode, the OVR flag is set in the SR register
+ * since the received data are never read. Therefore set OVR
+ * interrupt only when rx buffer is available.
+ */
+ stm32_spi_set_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_ERRIE);
+ }
+
+ stm32_spi_enable(spi);
+}
+
+/**
+ * stm32h7_spi_transfer_one_dma_start - Set SPI driver registers to start
+ * transfer using DMA
+ */
+static void stm32h7_spi_transfer_one_dma_start(struct stm32_spi *spi)
+{
+ /* Enable the interrupts relative to the end of transfer */
+ stm32_spi_set_bits(spi, STM32H7_SPI_IER, STM32H7_SPI_IER_EOTIE |
+ STM32H7_SPI_IER_TXTFIE |
+ STM32H7_SPI_IER_OVRIE |
+ STM32H7_SPI_IER_MODFIE);
+
+ stm32_spi_enable(spi);
+
+ stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_CSTART);
+}
+
+/**
* stm32_spi_transfer_one_dma - transfer a single spi_transfer using DMA
*
* It must returns 0 if the transfer is finished or 1 if the transfer is still
@@ -758,17 +1277,17 @@
struct dma_slave_config tx_dma_conf, rx_dma_conf;
struct dma_async_tx_descriptor *tx_dma_desc, *rx_dma_desc;
unsigned long flags;
- u32 ier = 0;
spin_lock_irqsave(&spi->lock, flags);
rx_dma_desc = NULL;
- if (spi->rx_buf) {
+ if (spi->rx_buf && spi->dma_rx) {
stm32_spi_dma_config(spi, &rx_dma_conf, DMA_DEV_TO_MEM);
dmaengine_slave_config(spi->dma_rx, &rx_dma_conf);
/* Enable Rx DMA request */
- stm32_spi_set_bits(spi, STM32_SPI_CFG1, SPI_CFG1_RXDMAEN);
+ stm32_spi_set_bits(spi, spi->cfg->regs->dma_rx_en.reg,
+ spi->cfg->regs->dma_rx_en.mask);
rx_dma_desc = dmaengine_prep_slave_sg(
spi->dma_rx, xfer->rx_sg.sgl,
@@ -778,7 +1297,7 @@
}
tx_dma_desc = NULL;
- if (spi->tx_buf) {
+ if (spi->tx_buf && spi->dma_tx) {
stm32_spi_dma_config(spi, &tx_dma_conf, DMA_MEM_TO_DEV);
dmaengine_slave_config(spi->dma_tx, &tx_dma_conf);
@@ -789,12 +1308,15 @@
DMA_PREP_INTERRUPT);
}
- if ((spi->tx_buf && !tx_dma_desc) ||
- (spi->rx_buf && !rx_dma_desc))
+ if ((spi->tx_buf && spi->dma_tx && !tx_dma_desc) ||
+ (spi->rx_buf && spi->dma_rx && !rx_dma_desc))
+ goto dma_desc_error;
+
+ if (spi->cur_comm == SPI_FULL_DUPLEX && (!tx_dma_desc || !rx_dma_desc))
goto dma_desc_error;
if (rx_dma_desc) {
- rx_dma_desc->callback = stm32_spi_dma_cb;
+ rx_dma_desc->callback = spi->cfg->dma_rx_cb;
rx_dma_desc->callback_param = spi;
if (dma_submit_error(dmaengine_submit(rx_dma_desc))) {
@@ -806,8 +1328,9 @@
}
if (tx_dma_desc) {
- if (spi->cur_comm == SPI_SIMPLEX_TX) {
- tx_dma_desc->callback = stm32_spi_dma_cb;
+ if (spi->cur_comm == SPI_SIMPLEX_TX ||
+ spi->cur_comm == SPI_3WIRE_TX) {
+ tx_dma_desc->callback = spi->cfg->dma_tx_cb;
tx_dma_desc->callback_param = spi;
}
@@ -819,33 +1342,228 @@
dma_async_issue_pending(spi->dma_tx);
/* Enable Tx DMA request */
- stm32_spi_set_bits(spi, STM32_SPI_CFG1, SPI_CFG1_TXDMAEN);
+ stm32_spi_set_bits(spi, spi->cfg->regs->dma_tx_en.reg,
+ spi->cfg->regs->dma_tx_en.mask);
}
- /* Enable the interrupts relative to the end of transfer */
- ier |= SPI_IER_EOTIE | SPI_IER_TXTFIE | SPI_IER_OVRIE | SPI_IER_MODFIE;
- writel_relaxed(ier, spi->base + STM32_SPI_IER);
-
- stm32_spi_enable(spi);
-
- stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_CSTART);
+ spi->cfg->transfer_one_dma_start(spi);
spin_unlock_irqrestore(&spi->lock, flags);
return 1;
dma_submit_error:
- if (spi->rx_buf)
+ if (spi->dma_rx)
dmaengine_terminate_all(spi->dma_rx);
dma_desc_error:
- stm32_spi_clr_bits(spi, STM32_SPI_CFG1, SPI_CFG1_RXDMAEN);
+ stm32_spi_clr_bits(spi, spi->cfg->regs->dma_rx_en.reg,
+ spi->cfg->regs->dma_rx_en.mask);
spin_unlock_irqrestore(&spi->lock, flags);
dev_info(spi->dev, "DMA issue: fall back to irq transfer\n");
- return stm32_spi_transfer_one_irq(spi);
+ spi->cur_usedma = false;
+ return spi->cfg->transfer_one_irq(spi);
+}
+
+/**
+ * stm32f4_spi_set_bpw - Configure bits per word
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32f4_spi_set_bpw(struct stm32_spi *spi)
+{
+ if (spi->cur_bpw == 16)
+ stm32_spi_set_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_DFF);
+ else
+ stm32_spi_clr_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_DFF);
+}
+
+/**
+ * stm32h7_spi_set_bpw - configure bits per word
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32h7_spi_set_bpw(struct stm32_spi *spi)
+{
+ u32 bpw, fthlv;
+ u32 cfg1_clrb = 0, cfg1_setb = 0;
+
+ bpw = spi->cur_bpw - 1;
+
+ cfg1_clrb |= STM32H7_SPI_CFG1_DSIZE;
+ cfg1_setb |= (bpw << STM32H7_SPI_CFG1_DSIZE_SHIFT) &
+ STM32H7_SPI_CFG1_DSIZE;
+
+ spi->cur_fthlv = stm32h7_spi_prepare_fthlv(spi);
+ fthlv = spi->cur_fthlv - 1;
+
+ cfg1_clrb |= STM32H7_SPI_CFG1_FTHLV;
+ cfg1_setb |= (fthlv << STM32H7_SPI_CFG1_FTHLV_SHIFT) &
+ STM32H7_SPI_CFG1_FTHLV;
+
+ writel_relaxed(
+ (readl_relaxed(spi->base + STM32H7_SPI_CFG1) &
+ ~cfg1_clrb) | cfg1_setb,
+ spi->base + STM32H7_SPI_CFG1);
+}
+
+/**
+ * stm32_spi_set_mbr - Configure baud rate divisor in master mode
+ * @spi: pointer to the spi controller data structure
+ * @mbrdiv: baud rate divisor value
+ */
+static void stm32_spi_set_mbr(struct stm32_spi *spi, u32 mbrdiv)
+{
+ u32 clrb = 0, setb = 0;
+
+ clrb |= spi->cfg->regs->br.mask;
+ setb |= ((u32)mbrdiv << spi->cfg->regs->br.shift) &
+ spi->cfg->regs->br.mask;
+
+ writel_relaxed((readl_relaxed(spi->base + spi->cfg->regs->br.reg) &
+ ~clrb) | setb,
+ spi->base + spi->cfg->regs->br.reg);
+}
+
+/**
+ * stm32_spi_communication_type - return transfer communication type
+ * @spi_dev: pointer to the spi device
+ * transfer: pointer to spi transfer
+ */
+static unsigned int stm32_spi_communication_type(struct spi_device *spi_dev,
+ struct spi_transfer *transfer)
+{
+ unsigned int type = SPI_FULL_DUPLEX;
+
+ if (spi_dev->mode & SPI_3WIRE) { /* MISO/MOSI signals shared */
+ /*
+ * SPI_3WIRE and xfer->tx_buf != NULL and xfer->rx_buf != NULL
+ * is forbidden and unvalidated by SPI subsystem so depending
+ * on the valid buffer, we can determine the direction of the
+ * transfer.
+ */
+ if (!transfer->tx_buf)
+ type = SPI_3WIRE_RX;
+ else
+ type = SPI_3WIRE_TX;
+ } else {
+ if (!transfer->tx_buf)
+ type = SPI_SIMPLEX_RX;
+ else if (!transfer->rx_buf)
+ type = SPI_SIMPLEX_TX;
+ }
+
+ return type;
+}
+
+/**
+ * stm32f4_spi_set_mode - configure communication mode
+ * @spi: pointer to the spi controller data structure
+ * @comm_type: type of communication to configure
+ */
+static int stm32f4_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
+{
+ if (comm_type == SPI_3WIRE_TX || comm_type == SPI_SIMPLEX_TX) {
+ stm32_spi_set_bits(spi, STM32F4_SPI_CR1,
+ STM32F4_SPI_CR1_BIDIMODE |
+ STM32F4_SPI_CR1_BIDIOE);
+ } else if (comm_type == SPI_FULL_DUPLEX) {
+ stm32_spi_clr_bits(spi, STM32F4_SPI_CR1,
+ STM32F4_SPI_CR1_BIDIMODE |
+ STM32F4_SPI_CR1_BIDIOE);
+ } else {
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * stm32h7_spi_set_mode - configure communication mode
+ * @spi: pointer to the spi controller data structure
+ * @comm_type: type of communication to configure
+ */
+static int stm32h7_spi_set_mode(struct stm32_spi *spi, unsigned int comm_type)
+{
+ u32 mode;
+ u32 cfg2_clrb = 0, cfg2_setb = 0;
+
+ if (comm_type == SPI_3WIRE_RX) {
+ mode = STM32H7_SPI_HALF_DUPLEX;
+ stm32_spi_clr_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_HDDIR);
+ } else if (comm_type == SPI_3WIRE_TX) {
+ mode = STM32H7_SPI_HALF_DUPLEX;
+ stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_HDDIR);
+ } else if (comm_type == SPI_SIMPLEX_RX) {
+ mode = STM32H7_SPI_SIMPLEX_RX;
+ } else if (comm_type == SPI_SIMPLEX_TX) {
+ mode = STM32H7_SPI_SIMPLEX_TX;
+ } else {
+ mode = STM32H7_SPI_FULL_DUPLEX;
+ }
+
+ cfg2_clrb |= STM32H7_SPI_CFG2_COMM;
+ cfg2_setb |= (mode << STM32H7_SPI_CFG2_COMM_SHIFT) &
+ STM32H7_SPI_CFG2_COMM;
+
+ writel_relaxed(
+ (readl_relaxed(spi->base + STM32H7_SPI_CFG2) &
+ ~cfg2_clrb) | cfg2_setb,
+ spi->base + STM32H7_SPI_CFG2);
+
+ return 0;
+}
+
+/**
+ * stm32h7_spi_data_idleness - configure minimum time delay inserted between two
+ * consecutive data frames in master mode
+ * @spi: pointer to the spi controller data structure
+ * @len: transfer len
+ */
+static void stm32h7_spi_data_idleness(struct stm32_spi *spi, u32 len)
+{
+ u32 cfg2_clrb = 0, cfg2_setb = 0;
+
+ cfg2_clrb |= STM32H7_SPI_CFG2_MIDI;
+ if ((len > 1) && (spi->cur_midi > 0)) {
+ u32 sck_period_ns = DIV_ROUND_UP(SPI_1HZ_NS, spi->cur_speed);
+ u32 midi = min((u32)DIV_ROUND_UP(spi->cur_midi, sck_period_ns),
+ (u32)STM32H7_SPI_CFG2_MIDI >>
+ STM32H7_SPI_CFG2_MIDI_SHIFT);
+
+ dev_dbg(spi->dev, "period=%dns, midi=%d(=%dns)\n",
+ sck_period_ns, midi, midi * sck_period_ns);
+ cfg2_setb |= (midi << STM32H7_SPI_CFG2_MIDI_SHIFT) &
+ STM32H7_SPI_CFG2_MIDI;
+ }
+
+ writel_relaxed((readl_relaxed(spi->base + STM32H7_SPI_CFG2) &
+ ~cfg2_clrb) | cfg2_setb,
+ spi->base + STM32H7_SPI_CFG2);
+}
+
+/**
+ * stm32h7_spi_number_of_data - configure number of data at current transfer
+ * @spi: pointer to the spi controller data structure
+ * @len: transfer length
+ */
+static int stm32h7_spi_number_of_data(struct stm32_spi *spi, u32 nb_words)
+{
+ u32 cr2_clrb = 0, cr2_setb = 0;
+
+ if (nb_words <= (STM32H7_SPI_CR2_TSIZE >>
+ STM32H7_SPI_CR2_TSIZE_SHIFT)) {
+ cr2_clrb |= STM32H7_SPI_CR2_TSIZE;
+ cr2_setb = nb_words << STM32H7_SPI_CR2_TSIZE_SHIFT;
+ writel_relaxed((readl_relaxed(spi->base + STM32H7_SPI_CR2) &
+ ~cr2_clrb) | cr2_setb,
+ spi->base + STM32H7_SPI_CR2);
+ } else {
+ return -EMSGSIZE;
+ }
+
+ return 0;
}
/**
@@ -858,91 +1576,44 @@
struct spi_transfer *transfer)
{
unsigned long flags;
- u32 cfg1_clrb = 0, cfg1_setb = 0, cfg2_clrb = 0, cfg2_setb = 0;
- u32 mode, nb_words;
- int ret = 0;
+ unsigned int comm_type;
+ int nb_words, ret = 0;
spin_lock_irqsave(&spi->lock, flags);
if (spi->cur_bpw != transfer->bits_per_word) {
- u32 bpw, fthlv;
-
spi->cur_bpw = transfer->bits_per_word;
- bpw = spi->cur_bpw - 1;
-
- cfg1_clrb |= SPI_CFG1_DSIZE;
- cfg1_setb |= (bpw << SPI_CFG1_DSIZE_SHIFT) & SPI_CFG1_DSIZE;
-
- spi->cur_fthlv = stm32_spi_prepare_fthlv(spi);
- fthlv = spi->cur_fthlv - 1;
-
- cfg1_clrb |= SPI_CFG1_FTHLV;
- cfg1_setb |= (fthlv << SPI_CFG1_FTHLV_SHIFT) & SPI_CFG1_FTHLV;
+ spi->cfg->set_bpw(spi);
}
if (spi->cur_speed != transfer->speed_hz) {
int mbr;
/* Update spi->cur_speed with real clock speed */
- mbr = stm32_spi_prepare_mbr(spi, transfer->speed_hz);
+ mbr = stm32_spi_prepare_mbr(spi, transfer->speed_hz,
+ spi->cfg->baud_rate_div_min,
+ spi->cfg->baud_rate_div_max);
if (mbr < 0) {
ret = mbr;
goto out;
}
transfer->speed_hz = spi->cur_speed;
-
- cfg1_clrb |= SPI_CFG1_MBR;
- cfg1_setb |= ((u32)mbr << SPI_CFG1_MBR_SHIFT) & SPI_CFG1_MBR;
+ stm32_spi_set_mbr(spi, mbr);
}
- if (cfg1_clrb || cfg1_setb)
- writel_relaxed((readl_relaxed(spi->base + STM32_SPI_CFG1) &
- ~cfg1_clrb) | cfg1_setb,
- spi->base + STM32_SPI_CFG1);
+ comm_type = stm32_spi_communication_type(spi_dev, transfer);
+ if (spi->cur_comm != comm_type) {
+ ret = spi->cfg->set_mode(spi, comm_type);
- mode = SPI_FULL_DUPLEX;
- if (spi_dev->mode & SPI_3WIRE) { /* MISO/MOSI signals shared */
- /*
- * SPI_3WIRE and xfer->tx_buf != NULL and xfer->rx_buf != NULL
- * is forbidden und unvalidated by SPI subsystem so depending
- * on the valid buffer, we can determine the direction of the
- * transfer.
- */
- mode = SPI_HALF_DUPLEX;
- if (!transfer->tx_buf)
- stm32_spi_clr_bits(spi, STM32_SPI_CR1, SPI_CR1_HDDIR);
- else if (!transfer->rx_buf)
- stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_HDDIR);
- } else {
- if (!transfer->tx_buf)
- mode = SPI_SIMPLEX_RX;
- else if (!transfer->rx_buf)
- mode = SPI_SIMPLEX_TX;
- }
- if (spi->cur_comm != mode) {
- spi->cur_comm = mode;
+ if (ret < 0)
+ goto out;
- cfg2_clrb |= SPI_CFG2_COMM;
- cfg2_setb |= (mode << SPI_CFG2_COMM_SHIFT) & SPI_CFG2_COMM;
+ spi->cur_comm = comm_type;
}
- cfg2_clrb |= SPI_CFG2_MIDI;
- if ((transfer->len > 1) && (spi->cur_midi > 0)) {
- u32 sck_period_ns = DIV_ROUND_UP(SPI_1HZ_NS, spi->cur_speed);
- u32 midi = min((u32)DIV_ROUND_UP(spi->cur_midi, sck_period_ns),
- (u32)SPI_CFG2_MIDI >> SPI_CFG2_MIDI_SHIFT);
-
- dev_dbg(spi->dev, "period=%dns, midi=%d(=%dns)\n",
- sck_period_ns, midi, midi * sck_period_ns);
-
- cfg2_setb |= (midi << SPI_CFG2_MIDI_SHIFT) & SPI_CFG2_MIDI;
- }
-
- if (cfg2_clrb || cfg2_setb)
- writel_relaxed((readl_relaxed(spi->base + STM32_SPI_CFG2) &
- ~cfg2_clrb) | cfg2_setb,
- spi->base + STM32_SPI_CFG2);
+ if (spi->cfg->set_data_idleness)
+ spi->cfg->set_data_idleness(spi, transfer->len);
if (spi->cur_bpw <= 8)
nb_words = transfer->len;
@@ -950,13 +1621,11 @@
nb_words = DIV_ROUND_UP(transfer->len * 8, 16);
else
nb_words = DIV_ROUND_UP(transfer->len * 8, 32);
- nb_words <<= SPI_CR2_TSIZE_SHIFT;
- if (nb_words <= SPI_CR2_TSIZE) {
- writel_relaxed(nb_words, spi->base + STM32_SPI_CR2);
- } else {
- ret = -EMSGSIZE;
- goto out;
+ if (spi->cfg->set_number_of_data) {
+ ret = spi->cfg->set_number_of_data(spi, nb_words);
+ if (ret < 0)
+ goto out;
}
spi->cur_xferlen = transfer->len;
@@ -997,7 +1666,7 @@
spi->rx_len = spi->rx_buf ? transfer->len : 0;
spi->cur_usedma = (master->can_dma &&
- stm32_spi_can_dma(master, spi_dev, transfer));
+ master->can_dma(master, spi_dev, transfer));
ret = stm32_spi_transfer_one_setup(spi, spi_dev, transfer);
if (ret) {
@@ -1008,47 +1677,73 @@
if (spi->cur_usedma)
return stm32_spi_transfer_one_dma(spi, transfer);
else
- return stm32_spi_transfer_one_irq(spi);
+ return spi->cfg->transfer_one_irq(spi);
}
/**
* stm32_spi_unprepare_msg - relax the hardware
- *
- * Normally, if TSIZE has been configured, we should relax the hardware at the
- * reception of the EOT interrupt. But in case of error, EOT will not be
- * raised. So the subsystem unprepare_message call allows us to properly
- * complete the transfer from an hardware point of view.
*/
static int stm32_spi_unprepare_msg(struct spi_master *master,
struct spi_message *msg)
{
struct stm32_spi *spi = spi_master_get_devdata(master);
- stm32_spi_disable(spi);
+ spi->cfg->disable(spi);
return 0;
}
/**
- * stm32_spi_config - Configure SPI controller as SPI master
+ * stm32f4_spi_config - Configure SPI controller as SPI master
*/
-static int stm32_spi_config(struct stm32_spi *spi)
+static int stm32f4_spi_config(struct stm32_spi *spi)
{
unsigned long flags;
spin_lock_irqsave(&spi->lock, flags);
/* Ensure I2SMOD bit is kept cleared */
- stm32_spi_clr_bits(spi, STM32_SPI_I2SCFGR, SPI_I2SCFGR_I2SMOD);
+ stm32_spi_clr_bits(spi, STM32F4_SPI_I2SCFGR,
+ STM32F4_SPI_I2SCFGR_I2SMOD);
+
+ /*
+ * - SS input value high
+ * - transmitter half duplex direction
+ * - Set the master mode (default Motorola mode)
+ * - Consider 1 master/n slaves configuration and
+ * SS input value is determined by the SSI bit
+ */
+ stm32_spi_set_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SSI |
+ STM32F4_SPI_CR1_BIDIOE |
+ STM32F4_SPI_CR1_MSTR |
+ STM32F4_SPI_CR1_SSM);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return 0;
+}
+
+/**
+ * stm32h7_spi_config - Configure SPI controller as SPI master
+ */
+static int stm32h7_spi_config(struct stm32_spi *spi)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ /* Ensure I2SMOD bit is kept cleared */
+ stm32_spi_clr_bits(spi, STM32H7_SPI_I2SCFGR,
+ STM32H7_SPI_I2SCFGR_I2SMOD);
/*
* - SS input value high
* - transmitter half duplex direction
* - automatic communication suspend when RX-Fifo is full
*/
- stm32_spi_set_bits(spi, STM32_SPI_CR1, SPI_CR1_SSI |
- SPI_CR1_HDDIR |
- SPI_CR1_MASRX);
+ stm32_spi_set_bits(spi, STM32H7_SPI_CR1, STM32H7_SPI_CR1_SSI |
+ STM32H7_SPI_CR1_HDDIR |
+ STM32H7_SPI_CR1_MASRX);
/*
* - Set the master mode (default Motorola mode)
@@ -1056,17 +1751,56 @@
* SS input value is determined by the SSI bit
* - keep control of all associated GPIOs
*/
- stm32_spi_set_bits(spi, STM32_SPI_CFG2, SPI_CFG2_MASTER |
- SPI_CFG2_SSM |
- SPI_CFG2_AFCNTR);
+ stm32_spi_set_bits(spi, STM32H7_SPI_CFG2, STM32H7_SPI_CFG2_MASTER |
+ STM32H7_SPI_CFG2_SSM |
+ STM32H7_SPI_CFG2_AFCNTR);
spin_unlock_irqrestore(&spi->lock, flags);
return 0;
}
+static const struct stm32_spi_cfg stm32f4_spi_cfg = {
+ .regs = &stm32f4_spi_regspec,
+ .get_bpw_mask = stm32f4_spi_get_bpw_mask,
+ .disable = stm32f4_spi_disable,
+ .config = stm32f4_spi_config,
+ .set_bpw = stm32f4_spi_set_bpw,
+ .set_mode = stm32f4_spi_set_mode,
+ .transfer_one_dma_start = stm32f4_spi_transfer_one_dma_start,
+ .dma_tx_cb = stm32f4_spi_dma_tx_cb,
+ .dma_rx_cb = stm32f4_spi_dma_rx_cb,
+ .transfer_one_irq = stm32f4_spi_transfer_one_irq,
+ .irq_handler_event = stm32f4_spi_irq_event,
+ .irq_handler_thread = stm32f4_spi_irq_thread,
+ .baud_rate_div_min = STM32F4_SPI_BR_DIV_MIN,
+ .baud_rate_div_max = STM32F4_SPI_BR_DIV_MAX,
+ .has_fifo = false,
+};
+
+static const struct stm32_spi_cfg stm32h7_spi_cfg = {
+ .regs = &stm32h7_spi_regspec,
+ .get_fifo_size = stm32h7_spi_get_fifo_size,
+ .get_bpw_mask = stm32h7_spi_get_bpw_mask,
+ .disable = stm32h7_spi_disable,
+ .config = stm32h7_spi_config,
+ .set_bpw = stm32h7_spi_set_bpw,
+ .set_mode = stm32h7_spi_set_mode,
+ .set_data_idleness = stm32h7_spi_data_idleness,
+ .set_number_of_data = stm32h7_spi_number_of_data,
+ .transfer_one_dma_start = stm32h7_spi_transfer_one_dma_start,
+ .dma_rx_cb = stm32h7_spi_dma_cb,
+ .dma_tx_cb = stm32h7_spi_dma_cb,
+ .transfer_one_irq = stm32h7_spi_transfer_one_irq,
+ .irq_handler_thread = stm32h7_spi_irq_thread,
+ .baud_rate_div_min = STM32H7_SPI_MBR_DIV_MIN,
+ .baud_rate_div_max = STM32H7_SPI_MBR_DIV_MAX,
+ .has_fifo = true,
+};
+
static const struct of_device_id stm32_spi_of_match[] = {
- { .compatible = "st,stm32h7-spi", },
+ { .compatible = "st,stm32h7-spi", .data = (void *)&stm32h7_spi_cfg },
+ { .compatible = "st,stm32f4-spi", .data = (void *)&stm32f4_spi_cfg },
{},
};
MODULE_DEVICE_TABLE(of, stm32_spi_of_match);
@@ -1090,12 +1824,17 @@
spi->master = master;
spin_lock_init(&spi->lock);
+ spi->cfg = (const struct stm32_spi_cfg *)
+ of_match_device(pdev->dev.driver->of_match_table,
+ &pdev->dev)->data;
+
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
spi->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(spi->base)) {
ret = PTR_ERR(spi->base);
goto err_master_put;
}
+
spi->phys_addr = (dma_addr_t)res->start;
spi->irq = platform_get_irq(pdev, 0);
@@ -1104,16 +1843,17 @@
ret = -ENOENT;
goto err_master_put;
}
- ret = devm_request_threaded_irq(&pdev->dev, spi->irq, NULL,
- stm32_spi_irq, IRQF_ONESHOT,
- pdev->name, master);
+ ret = devm_request_threaded_irq(&pdev->dev, spi->irq,
+ spi->cfg->irq_handler_event,
+ spi->cfg->irq_handler_thread,
+ IRQF_ONESHOT, pdev->name, master);
if (ret) {
dev_err(&pdev->dev, "irq%d request failed: %d\n", spi->irq,
ret);
goto err_master_put;
}
- spi->clk = devm_clk_get(&pdev->dev, 0);
+ spi->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(spi->clk)) {
ret = PTR_ERR(spi->clk);
dev_err(&pdev->dev, "clk get failed: %d\n", ret);
@@ -1139,9 +1879,10 @@
reset_control_deassert(spi->rst);
}
- spi->fifo_size = stm32_spi_get_fifo_size(spi);
+ if (spi->cfg->has_fifo)
+ spi->fifo_size = spi->cfg->get_fifo_size(spi);
- ret = stm32_spi_config(spi);
+ ret = spi->cfg->config(spi);
if (ret) {
dev_err(&pdev->dev, "controller configuration failed: %d\n",
ret);
@@ -1151,11 +1892,11 @@
master->dev.of_node = pdev->dev.of_node;
master->auto_runtime_pm = true;
master->bus_num = pdev->id;
- master->mode_bits = SPI_MODE_3 | SPI_CS_HIGH | SPI_LSB_FIRST |
- SPI_3WIRE | SPI_LOOP;
- master->bits_per_word_mask = stm32_spi_get_bpw_mask(spi);
- master->max_speed_hz = spi->clk_rate / SPI_MBR_DIV_MIN;
- master->min_speed_hz = spi->clk_rate / SPI_MBR_DIV_MAX;
+ master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST |
+ SPI_3WIRE;
+ master->bits_per_word_mask = spi->cfg->get_bpw_mask(spi);
+ master->max_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_min;
+ master->min_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_max;
master->setup = stm32_spi_setup;
master->prepare_message = stm32_spi_prepare_msg;
master->transfer_one = stm32_spi_transfer_one;
@@ -1233,7 +1974,7 @@
struct spi_master *master = platform_get_drvdata(pdev);
struct stm32_spi *spi = spi_master_get_devdata(master);
- stm32_spi_disable(spi);
+ spi->cfg->disable(spi);
if (master->dma_tx)
dma_release_channel(master->dma_tx);
diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index 5f19016..b9fb649 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -490,8 +490,8 @@
ti_qspi_write(qspi, MM_SWITCH, QSPI_SPI_SWITCH_REG);
if (qspi->ctrl_base) {
regmap_update_bits(qspi->ctrl_base, qspi->ctrl_reg,
- MEM_CS_EN(spi->chip_select),
- MEM_CS_MASK);
+ MEM_CS_MASK,
+ MEM_CS_EN(spi->chip_select));
}
qspi->mmap_enabled = true;
}
@@ -503,7 +503,7 @@
ti_qspi_write(qspi, 0, QSPI_SPI_SWITCH_REG);
if (qspi->ctrl_base)
regmap_update_bits(qspi->ctrl_base, qspi->ctrl_reg,
- 0, MEM_CS_MASK);
+ MEM_CS_MASK, 0);
qspi->mmap_enabled = false;
}
diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c
index 97d1375..e7e8ea1 100644
--- a/drivers/spi/spi-topcliff-pch.c
+++ b/drivers/spi/spi-topcliff-pch.c
@@ -1008,6 +1008,9 @@
/* RX */
dma->sg_rx_p = kcalloc(num, sizeof(*dma->sg_rx_p), GFP_ATOMIC);
+ if (!dma->sg_rx_p)
+ return;
+
sg_init_table(dma->sg_rx_p, num); /* Initialize SG table */
/* offset, length setting */
sg = dma->sg_rx_p;
@@ -1068,6 +1071,9 @@
}
dma->sg_tx_p = kcalloc(num, sizeof(*dma->sg_tx_p), GFP_ATOMIC);
+ if (!dma->sg_tx_p)
+ return;
+
sg_init_table(dma->sg_tx_p, num); /* Initialize SG table */
/* offset, length setting */
sg = dma->sg_tx_p;
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 9a7def7..93986f8 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -19,6 +19,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi-mem.h>
#include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/pm_runtime.h>
#include <linux/pm_domain.h>
#include <linux/property.h>
@@ -578,7 +579,10 @@
goto done;
}
- if (ctlr->cs_gpios)
+ /* Descriptors take precedence */
+ if (ctlr->cs_gpiods)
+ spi->cs_gpiod = ctlr->cs_gpiods[spi->chip_select];
+ else if (ctlr->cs_gpios)
spi->cs_gpio = ctlr->cs_gpios[spi->chip_select];
/* Drivers may modify this initial i/o setup, but will
@@ -772,10 +776,21 @@
if (spi->mode & SPI_CS_HIGH)
enable = !enable;
- if (gpio_is_valid(spi->cs_gpio)) {
- /* Honour the SPI_NO_CS flag */
- if (!(spi->mode & SPI_NO_CS))
- gpio_set_value(spi->cs_gpio, !enable);
+ if (spi->cs_gpiod || gpio_is_valid(spi->cs_gpio)) {
+ /*
+ * Honour the SPI_NO_CS flag and invert the enable line, as
+ * active low is default for SPI. Execution paths that handle
+ * polarity inversion in gpiolib (such as device tree) will
+ * enforce active high using the SPI_CS_HIGH resulting in a
+ * double inversion through the code above.
+ */
+ if (!(spi->mode & SPI_NO_CS)) {
+ if (spi->cs_gpiod)
+ gpiod_set_value_cansleep(spi->cs_gpiod,
+ !enable);
+ else
+ gpio_set_value_cansleep(spi->cs_gpio, !enable);
+ }
/* Some SPI masters need both GPIO CS & slave_select */
if ((spi->controller->flags & SPI_MASTER_GPIO_SS) &&
spi->controller->set_cs)
@@ -1615,13 +1630,21 @@
spi->mode |= SPI_CPHA;
if (of_property_read_bool(nc, "spi-cpol"))
spi->mode |= SPI_CPOL;
- if (of_property_read_bool(nc, "spi-cs-high"))
- spi->mode |= SPI_CS_HIGH;
if (of_property_read_bool(nc, "spi-3wire"))
spi->mode |= SPI_3WIRE;
if (of_property_read_bool(nc, "spi-lsb-first"))
spi->mode |= SPI_LSB_FIRST;
+ /*
+ * For descriptors associated with the device, polarity inversion is
+ * handled in the gpiolib, so all chip selects are "active high" in
+ * the logical sense, the gpiolib will invert the line if need be.
+ */
+ if (ctlr->use_gpio_descriptors)
+ spi->mode |= SPI_CS_HIGH;
+ else if (of_property_read_bool(nc, "spi-cs-high"))
+ spi->mode |= SPI_CS_HIGH;
+
/* Device DUAL/QUAD mode */
if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
switch (value) {
@@ -2137,6 +2160,60 @@
}
#endif
+/**
+ * spi_get_gpio_descs() - grab chip select GPIOs for the master
+ * @ctlr: The SPI master to grab GPIO descriptors for
+ */
+static int spi_get_gpio_descs(struct spi_controller *ctlr)
+{
+ int nb, i;
+ struct gpio_desc **cs;
+ struct device *dev = &ctlr->dev;
+
+ nb = gpiod_count(dev, "cs");
+ ctlr->num_chipselect = max_t(int, nb, ctlr->num_chipselect);
+
+ /* No GPIOs at all is fine, else return the error */
+ if (nb == 0 || nb == -ENOENT)
+ return 0;
+ else if (nb < 0)
+ return nb;
+
+ cs = devm_kcalloc(dev, ctlr->num_chipselect, sizeof(*cs),
+ GFP_KERNEL);
+ if (!cs)
+ return -ENOMEM;
+ ctlr->cs_gpiods = cs;
+
+ for (i = 0; i < nb; i++) {
+ /*
+ * Most chipselects are active low, the inverted
+ * semantics are handled by special quirks in gpiolib,
+ * so initializing them GPIOD_OUT_LOW here means
+ * "unasserted", in most cases this will drive the physical
+ * line high.
+ */
+ cs[i] = devm_gpiod_get_index_optional(dev, "cs", i,
+ GPIOD_OUT_LOW);
+
+ if (cs[i]) {
+ /*
+ * If we find a CS GPIO, name it after the device and
+ * chip select line.
+ */
+ char *gpioname;
+
+ gpioname = devm_kasprintf(dev, GFP_KERNEL, "%s CS%d",
+ dev_name(dev), i);
+ if (!gpioname)
+ return -ENOMEM;
+ gpiod_set_consumer_name(cs[i], gpioname);
+ }
+ }
+
+ return 0;
+}
+
static int spi_controller_check_ops(struct spi_controller *ctlr)
{
/*
@@ -2199,9 +2276,21 @@
return status;
if (!spi_controller_is_slave(ctlr)) {
- status = of_spi_register_master(ctlr);
- if (status)
- return status;
+ if (ctlr->use_gpio_descriptors) {
+ status = spi_get_gpio_descs(ctlr);
+ if (status)
+ return status;
+ /*
+ * A controller using GPIO descriptors always
+ * supports SPI_CS_HIGH if need be.
+ */
+ ctlr->mode_bits |= SPI_CS_HIGH;
+ } else {
+ /* Legacy code path for GPIOs from DT */
+ status = of_spi_register_master(ctlr);
+ if (status)
+ return status;
+ }
}
/* even if it's just one always-selected device, there must
@@ -2915,6 +3004,7 @@
* cs_change is set for each transfer.
*/
if ((spi->mode & SPI_CS_WORD) && (!(ctlr->mode_bits & SPI_CS_WORD) ||
+ spi->cs_gpiod ||
gpio_is_valid(spi->cs_gpio))) {
size_t maxsize;
int ret;
@@ -2961,6 +3051,8 @@
* it is not set for this transfer.
* Set transfer tx_nbits and rx_nbits as single transfer default
* (SPI_NBITS_SINGLE) if it is not set for this transfer.
+ * Ensure transfer word_delay is at least as long as that required by
+ * device itself.
*/
message->frame_length = 0;
list_for_each_entry(xfer, &message->transfers, transfer_list) {
@@ -3031,6 +3123,9 @@
!(spi->mode & SPI_RX_QUAD))
return -EINVAL;
}
+
+ if (xfer->word_delay_usecs < spi->word_delay_usecs)
+ xfer->word_delay_usecs = spi->word_delay_usecs;
}
message->status = -EINPROGRESS;
diff --git a/arch/mips/include/asm/mach-ath79/ath79_spi_platform.h b/include/linux/platform_data/spi-ath79.h
similarity index 100%
rename from arch/mips/include/asm/mach-ath79/ath79_spi_platform.h
rename to include/linux/platform_data/spi-ath79.h
diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h
index b0674e3..c1c5947 100644
--- a/include/linux/spi/pxa2xx_spi.h
+++ b/include/linux/spi/pxa2xx_spi.h
@@ -22,7 +22,7 @@
struct dma_chan;
/* device.platform_data for SSP controller devices */
-struct pxa2xx_spi_master {
+struct pxa2xx_spi_controller {
u16 num_chipselect;
u8 enable_dma;
bool is_slave;
@@ -54,7 +54,7 @@
#include <linux/clk.h>
-extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
+extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_controller *info);
#endif
#endif
diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index 3fe2450..3703d0d 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h
@@ -330,6 +330,11 @@
u64 offs, size_t len, void *buf);
ssize_t spi_mem_dirmap_write(struct spi_mem_dirmap_desc *desc,
u64 offs, size_t len, const void *buf);
+struct spi_mem_dirmap_desc *
+devm_spi_mem_dirmap_create(struct device *dev, struct spi_mem *mem,
+ const struct spi_mem_dirmap_info *info);
+void devm_spi_mem_dirmap_destroy(struct device *dev,
+ struct spi_mem_dirmap_desc *desc);
int spi_mem_driver_register_with_owner(struct spi_mem_driver *drv,
struct module *owner);
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 314d922..662b336 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -12,6 +12,7 @@
#include <linux/kthread.h>
#include <linux/completion.h>
#include <linux/scatterlist.h>
+#include <linux/gpio/consumer.h>
struct dma_chan;
struct property_entry;
@@ -116,8 +117,13 @@
* @modalias: Name of the driver to use with this device, or an alias
* for that name. This appears in the sysfs "modalias" attribute
* for driver coldplugging, and in uevents used for hotplugging
- * @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when
+ * @cs_gpio: LEGACY: gpio number of the chipselect line (optional, -ENOENT when
+ * not using a GPIO line) use cs_gpiod in new drivers by opting in on
+ * the spi_master.
+ * @cs_gpiod: gpio descriptor of the chipselect line (optional, NULL when
* not using a GPIO line)
+ * @word_delay_usecs: microsecond delay to be inserted between consecutive
+ * words of a transfer
*
* @statistics: statistics for the spi_device
*
@@ -163,7 +169,9 @@
void *controller_data;
char modalias[SPI_NAME_SIZE];
const char *driver_override;
- int cs_gpio; /* chip select gpio */
+ int cs_gpio; /* LEGACY: chip select gpio */
+ struct gpio_desc *cs_gpiod; /* chip select gpio desc */
+ uint8_t word_delay_usecs; /* inter-word delay */
/* the statistics */
struct spi_statistics statistics;
@@ -376,9 +384,17 @@
* controller has native support for memory like operations.
* @unprepare_message: undo any work done by prepare_message().
* @slave_abort: abort the ongoing transfer request on an SPI slave controller
- * @cs_gpios: Array of GPIOs to use as chip select lines; one per CS
- * number. Any individual value may be -ENOENT for CS lines that
+ * @cs_gpios: LEGACY: array of GPIO descs to use as chip select lines; one per
+ * CS number. Any individual value may be -ENOENT for CS lines that
+ * are not GPIOs (driven by the SPI controller itself). Use the cs_gpiods
+ * in new drivers.
+ * @cs_gpiods: Array of GPIO descs to use as chip select lines; one per CS
+ * number. Any individual value may be NULL for CS lines that
* are not GPIOs (driven by the SPI controller itself).
+ * @use_gpio_descriptors: Turns on the code in the SPI core to parse and grab
+ * GPIO descriptors rather than using global GPIO numbers grabbed by the
+ * driver. This will fill in @cs_gpiods and @cs_gpios should not be used,
+ * and SPI devices will have the cs_gpiod assigned rather than cs_gpio.
* @statistics: statistics for the spi_controller
* @dma_tx: DMA transmit channel
* @dma_rx: DMA receive channel
@@ -557,6 +573,8 @@
/* gpio chip select */
int *cs_gpios;
+ struct gpio_desc **cs_gpiods;
+ bool use_gpio_descriptors;
/* statistics */
struct spi_statistics statistics;
@@ -706,6 +724,8 @@
* @delay_usecs: microseconds to delay after this transfer before
* (optionally) changing the chipselect status, then starting
* the next transfer or completing this @spi_message.
+ * @word_delay_usecs: microseconds to inter word delay after each word size
+ * (set by bits_per_word) transmission.
* @word_delay: clock cycles to inter word delay after each word size
* (set by bits_per_word) transmission.
* @transfer_list: transfers are sequenced through @spi_message.transfers
@@ -788,6 +808,7 @@
#define SPI_NBITS_DUAL 0x02 /* 2bits transfer */
#define SPI_NBITS_QUAD 0x04 /* 4bits transfer */
u8 bits_per_word;
+ u8 word_delay_usecs;
u16 delay_usecs;
u32 speed_hz;
u16 word_delay;
diff --git a/include/trace/events/spi.h b/include/trace/events/spi.h
index 277bb9d..aef6869 100644
--- a/include/trace/events/spi.h
+++ b/include/trace/events/spi.h
@@ -109,6 +109,16 @@
(unsigned)__entry->actual, (unsigned)__entry->frame)
);
+/*
+ * consider a buffer valid if non-NULL and if it doesn't match the dummy buffer
+ * that only exist to work with controllers that have SPI_CONTROLLER_MUST_TX or
+ * SPI_CONTROLLER_MUST_RX.
+ */
+#define spi_valid_txbuf(msg, xfer) \
+ (xfer->tx_buf && xfer->tx_buf != msg->spi->controller->dummy_tx)
+#define spi_valid_rxbuf(msg, xfer) \
+ (xfer->rx_buf && xfer->rx_buf != msg->spi->controller->dummy_rx)
+
DECLARE_EVENT_CLASS(spi_transfer,
TP_PROTO(struct spi_message *msg, struct spi_transfer *xfer),
@@ -120,6 +130,10 @@
__field( int, chip_select )
__field( struct spi_transfer *, xfer )
__field( int, len )
+ __dynamic_array(u8, rx_buf,
+ spi_valid_rxbuf(msg, xfer) ? xfer->len : 0)
+ __dynamic_array(u8, tx_buf,
+ spi_valid_txbuf(msg, xfer) ? xfer->len : 0)
),
TP_fast_assign(
@@ -127,12 +141,21 @@
__entry->chip_select = msg->spi->chip_select;
__entry->xfer = xfer;
__entry->len = xfer->len;
+
+ if (spi_valid_txbuf(msg, xfer))
+ memcpy(__get_dynamic_array(tx_buf),
+ xfer->tx_buf, xfer->len);
+
+ if (spi_valid_rxbuf(msg, xfer))
+ memcpy(__get_dynamic_array(rx_buf),
+ xfer->rx_buf, xfer->len);
),
- TP_printk("spi%d.%d %p len=%d", (int)__entry->bus_num,
- (int)__entry->chip_select,
- (struct spi_message *)__entry->xfer,
- (int)__entry->len)
+ TP_printk("spi%d.%d %p len=%d tx=[%*phD] rx=[%*phD]",
+ __entry->bus_num, __entry->chip_select,
+ __entry->xfer, __entry->len,
+ __get_dynamic_array_len(tx_buf), __get_dynamic_array(tx_buf),
+ __get_dynamic_array_len(rx_buf), __get_dynamic_array(rx_buf))
);
DEFINE_EVENT(spi_transfer, spi_transfer_start,
