blob: ee4fc0576c7d866b318eda917066e76e920b4f53 [file] [log] [blame]
* Samsung Exynos specific extensions to the Synopsys Designware Mobile
Storage Host Controller
The Synopsys designware mobile storage host controller is used to interface
a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
differences between the core Synopsys dw mshc controller properties described
by synopsys-dw-mshc.txt and the properties used by the Samsung Exynos specific
extensions to the Synopsys Designware Mobile Storage Host Controller.
Required Properties:
* compatible: should be
- "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
specific extensions.
- "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
specific extensions.
- "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
specific extensions.
- "samsung,exynos5420-dw-mshc": for controllers with Samsung Exynos5420
specific extensions.
- "samsung,exynos7-dw-mshc": for controllers with Samsung Exynos7
specific extensions.
- "samsung,exynos7-dw-mshc-smu": for controllers with Samsung Exynos7
specific extensions having an SMU.
* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
in transmit mode and CIU clock phase shift value in receive mode for single
data rate mode operation. Refer notes below for the order of the cells and the
valid values.
* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
in transmit mode and CIU clock phase shift value in receive mode for double
data rate mode operation. Refer notes below for the order of the cells and the
valid values.
Notes for the sdr-timing and ddr-timing values:
The order of the cells should be
- First Cell: CIU clock phase shift value for tx mode.
- Second Cell: CIU clock phase shift value for rx mode.
Valid values for SDR and DDR CIU clock timing for Exynos5250:
- valid value for tx phase shift and rx phase shift is 0 to 7.
- when CIU clock divider value is set to 3, all possible 8 phase shift
values can be used.
- if CIU clock divider value is 0 (that is divide by 1), both tx and rx
phase shift clocks should be 0.
Required properties for a slot (Deprecated - Recommend to use one slot per host):
* gpios: specifies a list of gpios used for command, clock and data bus. The
first gpio is the command line and the second gpio is the clock line. The
rest of the gpios (depending on the bus-width property) are the data lines in
no particular order. The format of the gpio specifier depends on the gpio
controller.
(Deprecated - Refer to Documentation/devicetree/binding/pinctrl/samsung-pinctrl.txt)
Example:
The MSHC controller node can be split into two portions, SoC specific and
board specific portions as listed below.
dwmmc0@12200000 {
compatible = "samsung,exynos5250-dw-mshc";
reg = <0x12200000 0x1000>;
interrupts = <0 75 0>;
#address-cells = <1>;
#size-cells = <0>;
};
dwmmc0@12200000 {
num-slots = <1>;
cap-mmc-highspeed;
cap-sd-highspeed;
broken-cd;
fifo-depth = <0x80>;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
bus-width = <8>;
};