diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
index cd5e239..6794cdc 100644
--- a/Documentation/devicetree/bindings/clock/at91-clock.txt
+++ b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -62,7 +62,7 @@
 - interrupt-controller : tell that the PMC is an interrupt controller.
 - #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
 	and reflect the bit position in the PMC_ER/DR/SR registers.
-	You can use the dt macros defined in dt-bindings/clk/at91.h.
+	You can use the dt macros defined in dt-bindings/clock/at91.h.
 	0 (AT91_PMC_MOSCS) -> main oscillator ready
 	1 (AT91_PMC_LOCKA) -> PLL A ready
 	2 (AT91_PMC_LOCKB) -> PLL B ready
diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt
index 9fbbdb7..68ff213 100644
--- a/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -29,6 +29,6 @@
 	dma-channels = <64>;
 	ti,edma-regions = <4>;
 	ti,edma-slots = <256>;
-	ti,edma-xbar-event-map = <1 12
-				  2 13>;
+	ti,edma-xbar-event-map = /bits/ 16 <1 12
+					    2 13>;
 };
diff --git a/MAINTAINERS b/MAINTAINERS
index 764075d..c596b74 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1893,14 +1893,15 @@
 S:	Supported
 F:	drivers/net/ethernet/broadcom/bnx2x/
 
-BROADCOM BCM281XX/BCM11XXX ARM ARCHITECTURE
+BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
 M:	Christian Daudt <bcm@fixthebug.org>
 M:	Matt Porter <mporter@linaro.org>
 L:	bcm-kernel-feedback-list@broadcom.com
-T:	git git://git.github.com/broadcom/bcm11351
+T:	git git://github.com/broadcom/mach-bcm
 S:	Maintained
 F:	arch/arm/mach-bcm/
 F:	arch/arm/boot/dts/bcm113*
+F:	arch/arm/boot/dts/bcm216*
 F:	arch/arm/boot/dts/bcm281*
 F:	arch/arm/configs/bcm_defconfig
 F:	drivers/mmc/host/sdhci_bcm_kona.c
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index cb6811e..7ad75b4 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -144,7 +144,7 @@
 			compatible = "ti,edma3";
 			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
 			reg =	<0x49000000 0x10000>,
-				<0x44e10f90 0x10>;
+				<0x44e10f90 0x40>;
 			interrupts = <12 13 14>;
 			#dma-cells = <1>;
 			dma-channels = <64>;
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi
index 788391f..5a452fd 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/am3517.dtsi
@@ -62,5 +62,21 @@
 	};
 };
 
+&iva {
+	status = "disabled";
+};
+
+&mailbox {
+	status = "disabled";
+};
+
+&mmu_isp {
+	status = "disabled";
+};
+
+&smartreflex_mpu_iva {
+	status = "disabled";
+};
+
 /include/ "am35xx-clocks.dtsi"
 /include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index df8798e..a055f7f 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -117,6 +117,11 @@
 	status = "okay";
 };
 
+&gpio5 {
+	status = "okay";
+	ti,no-reset-on-init;
+};
+
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmcsd_fixed>;
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 82f238a..3383c4b 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -67,6 +67,7 @@
 			i2c@11000 {
 				pinctrl-0 = <&i2c0_pins>;
 				pinctrl-names = "default";
+				clock-frequency = <100000>;
 				status = "okay";
 				audio_codec: audio-codec@4a {
 					compatible = "cirrus,cs42l51";
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index 9378d31..0451124 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -79,6 +79,11 @@
 				};
 			};
 
+			sata@a0000 {
+				status = "okay";
+				nr-ports = <2>;
+			};
+
 			nand: nand@d0000 {
 				pinctrl-0 = <&nand_pins>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index 448373c..90f0bf6 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -49,7 +49,7 @@
 			/* Device Bus parameters are required */
 
 			/* Read parameters */
-			devbus,bus-width    = <8>;
+			devbus,bus-width    = <16>;
 			devbus,turn-off-ps  = <60000>;
 			devbus,badr-skew-ps = <0>;
 			devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 61bda68..0c75642 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -59,7 +59,7 @@
 			/* Device Bus parameters are required */
 
 			/* Read parameters */
-			devbus,bus-width    = <8>;
+			devbus,bus-width    = <16>;
 			devbus,turn-off-ps  = <60000>;
 			devbus,badr-skew-ps = <0>;
 			devbus,acc-first-ps = <124000>;
@@ -146,22 +146,22 @@
 			ethernet@70000 {
 				status = "okay";
 				phy = <&phy0>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 			ethernet@74000 {
 				status = "okay";
 				phy = <&phy1>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 			ethernet@30000 {
 				status = "okay";
 				phy = <&phy2>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 			ethernet@34000 {
 				status = "okay";
 				phy = <&phy3>;
-				phy-mode = "rgmii-id";
+				phy-mode = "qsgmii";
 			};
 
 			/* Front-side USB slot */
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index 985948c..5d42feb 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -39,7 +39,7 @@
 			/* Device Bus parameters are required */
 
 			/* Read parameters */
-			devbus,bus-width    = <8>;
+			devbus,bus-width    = <16>;
 			devbus,turn-off-ps  = <60000>;
 			devbus,badr-skew-ps = <0>;
 			devbus,acc-first-ps = <124000>;
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index ce13755..4537259 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -34,7 +34,7 @@
 			};
 
 			spi0: spi@f0004000 {
-				cs-gpios = <&pioD 13 0>;
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
 			};
 
@@ -79,7 +79,7 @@
 			};
 
 			spi1: spi@f8008000 {
-				cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
+				cs-gpios = <&pioC 25 0>;
 				status = "okay";
 			};
 
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index e21dda0e..3be973e 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -10,7 +10,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	model = "Atmel AT91SAM9261 family SoC";
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 63e1784..92a52fa 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -8,7 +8,7 @@
 
 #include "skeleton.dtsi"
 #include <dt-bindings/pinctrl/at91.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 9c2bff2..6a1bf4f 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -115,7 +115,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "fsl,imx53-ipu";
-			reg = <0x18000000 0x080000000>;
+			reg = <0x18000000 0x08000000>;
 			interrupts = <11 10>;
 			clocks = <&clks IMX5_CLK_IPU_GATE>,
 			         <&clks IMX5_CLK_IPU_DI0_GATE>,
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
index 32c6fb4..b939f4f5 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -30,6 +30,16 @@
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
 	};
 
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+        };
+
 	ocp@f1000000 {
 		pinctrl@10000 {
 			pmx_usb_led: pmx-usb-led {
@@ -73,14 +83,6 @@
 		ehci@50000 {
 			status = "okay";
 		};
-
-		pcie-controller {
-			status = "okay";
-
-			pcie@1,0 {
-				status = "okay";
-			};
-		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
index aa78c2d..e2cc85c 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi
@@ -4,6 +4,16 @@
 / {
 	model = "ZyXEL NSA310";
 
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
 	ocp@f1000000 {
 		pinctrl: pinctrl@10000 {
 
@@ -26,14 +36,6 @@
 			status = "okay";
 			nr-ports = <2>;
 		};
-
-		pcie-controller {
-			status = "okay";
-
-			pcie@1,0 {
-				status = "okay";
-			};
-		};
 	};
 
 	gpio_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
index 7d1c767..0bd70d9 100644
--- a/arch/arm/boot/dts/kirkwood-t5325.dts
+++ b/arch/arm/boot/dts/kirkwood-t5325.dts
@@ -127,11 +127,6 @@
 
 		i2c@11000 {
 			status = "okay";
-
-			alc5621: alc5621@1a {
-				compatible = "realtek,alc5621";
-				reg = <0x1a>;
-			};
 		};
 
 		serial@12000 {
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
index f577b7d..521c587 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -24,11 +24,10 @@
 		compatible = "smsc,lan9221", "smsc,lan9115";
 		bank-width = <2>;
 		gpmc,mux-add-data;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <186>;
-		gpmc,cs-wr-off-ns = <186>;
-		gpmc,adv-on-ns = <12>;
-		gpmc,adv-rd-off-ns = <48>;
+		gpmc,cs-on-ns = <1>;
+		gpmc,cs-rd-off-ns = <180>;
+		gpmc,cs-wr-off-ns = <180>;
+		gpmc,adv-rd-off-ns = <18>;
 		gpmc,adv-wr-off-ns = <48>;
 		gpmc,oe-on-ns = <54>;
 		gpmc,oe-off-ns = <168>;
@@ -36,12 +35,10 @@
 		gpmc,we-off-ns = <168>;
 		gpmc,rd-cycle-ns = <186>;
 		gpmc,wr-cycle-ns = <186>;
-		gpmc,access-ns = <114>;
-		gpmc,page-burst-access-ns = <6>;
-		gpmc,bus-turnaround-ns = <12>;
-		gpmc,cycle2cycle-delay-ns = <18>;
-		gpmc,wr-data-mux-bus-ns = <90>;
-		gpmc,wr-access-ns = <186>;
+		gpmc,access-ns = <144>;
+		gpmc,page-burst-access-ns = <24>;
+		gpmc,bus-turnaround-ns = <90>;
+		gpmc,cycle2cycle-delay-ns = <90>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
 		vddvario-supply = <&vddvario>;
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index 22f35ea..8f8c07d 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -71,13 +71,6 @@
 			interrupts = <58>;
 		};
 
-		mailbox: mailbox@48094000 {
-			compatible = "ti,omap2-mailbox";
-			ti,hwmods = "mailbox";
-			reg = <0x48094000 0x200>;
-			interrupts = <26>;
-		};
-
 		intc: interrupt-controller@1 {
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi
index 85b1fb0..2d99798 100644
--- a/arch/arm/boot/dts/omap2420.dtsi
+++ b/arch/arm/boot/dts/omap2420.dtsi
@@ -125,6 +125,14 @@
 			dma-names = "tx", "rx";
 		};
 
+		mailbox: mailbox@48094000 {
+			compatible = "ti,omap2-mailbox";
+			reg = <0x48094000 0x200>;
+			interrupts = <26>, <34>;
+			interrupt-names = "dsp", "iva";
+			ti,hwmods = "mailbox";
+		};
+
 		timer1: timer@48028000 {
 			compatible = "ti,omap2420-timer";
 			reg = <0x48028000 0x400>;
diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi
index d09697d..42d2c61 100644
--- a/arch/arm/boot/dts/omap2430.dtsi
+++ b/arch/arm/boot/dts/omap2430.dtsi
@@ -216,6 +216,13 @@
 			dma-names = "tx", "rx";
 		};
 
+		mailbox: mailbox@48094000 {
+			compatible = "ti,omap2-mailbox";
+			reg = <0x48094000 0x200>;
+			interrupts = <26>;
+			ti,hwmods = "mailbox";
+		};
+
 		timer1: timer@49018000 {
 			compatible = "ti,omap2420-timer";
 			reg = <0x49018000 0x400>;
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
index d000558..25ba083 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -10,18 +10,6 @@
 			cpu0-supply = <&vcc>;
 		};
 	};
-
-	vddvario: regulator-vddvario {
-		compatible = "regulator-fixed";
-		regulator-name = "vddvario";
-		regulator-always-on;
-	};
-
-	vdd33a: regulator-vdd33a {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd33a";
-		regulator-always-on;
-	};
 };
 
 &omap3_pmx_core {
@@ -35,58 +23,34 @@
 
  	hsusb0_pins: pinmux_hsusb0_pins {
 		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
-			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
-			OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
-			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
-			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
-			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
-			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
-			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
-			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
-			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
-			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
-			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
+			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
+			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
+			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
+			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
+			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
+			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
+			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
+			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
+			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
+			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
+			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
+			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
 		>;
 	};
 };
 
+#include "omap-gpmc-smsc911x.dtsi"
+
 &gpmc {
 	ranges = <5 0 0x2c000000 0x01000000>;
 
-	smsc1: ethernet@5,0 {
+	smsc1: ethernet@gpmc {
 		compatible = "smsc,lan9221", "smsc,lan9115";
 		pinctrl-names = "default";
 		pinctrl-0 = <&smsc1_pins>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		reg = <5 0 0xff>;
-		bank-width = <2>;
-		gpmc,mux-add-data;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <186>;
-		gpmc,cs-wr-off-ns = <186>;
-		gpmc,adv-on-ns = <12>;
-		gpmc,adv-rd-off-ns = <48>;
-		gpmc,adv-wr-off-ns = <48>;
-		gpmc,oe-on-ns = <54>;
-		gpmc,oe-off-ns = <168>;
-		gpmc,we-on-ns = <54>;
-		gpmc,we-off-ns = <168>;
-		gpmc,rd-cycle-ns = <186>;
-		gpmc,wr-cycle-ns = <186>;
-		gpmc,access-ns = <114>;
-		gpmc,page-burst-access-ns = <6>;
-		gpmc,bus-turnaround-ns = <12>;
-		gpmc,cycle2cycle-delay-ns = <18>;
-		gpmc,wr-data-mux-bus-ns = <90>;
-		gpmc,wr-access-ns = <186>;
-		gpmc,cycle2cycle-samecsen;
-		gpmc,cycle2cycle-diffcsen;
-		vddvario-supply = <&vddvario>;
-		vdd33a-supply = <&vdd33a>;
-		reg-io-width = <4>;
-		smsc,save-mac-address;
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index b97736d..e2d163b 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -107,7 +107,7 @@
 		>;
 	};
 
-	smsc911x_pins: pinmux_smsc911x_pins {
+	smsc9221_pins: pinmux_smsc9221_pins {
 		pinctrl-single,pins = <
 			0x1a2 (PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
 		>;
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 7abd64f..b22caaa 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -10,7 +10,7 @@
  */
 
 #include "omap3-igep.dtsi"
-#include "omap-gpmc-smsc911x.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
 
 / {
 	model = "IGEPv2 (TI OMAP AM/DM37x)";
@@ -248,7 +248,7 @@
 
 	ethernet@gpmc {
 		pinctrl-names = "default";
-		pinctrl-0 = <&smsc911x_pins>;
+		pinctrl-0 = <&smsc9221_pins>;
 		reg = <5 0 0xff>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi
index 7909c51..d59e3de 100644
--- a/arch/arm/boot/dts/omap3-sb-t35.dtsi
+++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi
@@ -2,20 +2,6 @@
  * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
  */
 
-/ {
-	vddvario_sb_t35: regulator-vddvario-sb-t35 {
-		compatible = "regulator-fixed";
-		regulator-name = "vddvario";
-		regulator-always-on;
-	};
-
-	vdd33a_sb_t35: regulator-vdd33a-sb-t35 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd33a";
-		regulator-always-on;
-	};
-};
-
 &omap3_pmx_core {
 	smsc2_pins: pinmux_smsc2_pins {
 		pinctrl-single,pins = <
@@ -37,11 +23,10 @@
 		reg = <4 0 0xff>;
 		bank-width = <2>;
 		gpmc,mux-add-data;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <186>;
-		gpmc,cs-wr-off-ns = <186>;
-		gpmc,adv-on-ns = <12>;
-		gpmc,adv-rd-off-ns = <48>;
+		gpmc,cs-on-ns = <1>;
+		gpmc,cs-rd-off-ns = <180>;
+		gpmc,cs-wr-off-ns = <180>;
+		gpmc,adv-rd-off-ns = <18>;
 		gpmc,adv-wr-off-ns = <48>;
 		gpmc,oe-on-ns = <54>;
 		gpmc,oe-off-ns = <168>;
@@ -49,16 +34,14 @@
 		gpmc,we-off-ns = <168>;
 		gpmc,rd-cycle-ns = <186>;
 		gpmc,wr-cycle-ns = <186>;
-		gpmc,access-ns = <114>;
-		gpmc,page-burst-access-ns = <6>;
-		gpmc,bus-turnaround-ns = <12>;
-		gpmc,cycle2cycle-delay-ns = <18>;
-		gpmc,wr-data-mux-bus-ns = <90>;
-		gpmc,wr-access-ns = <186>;
+		gpmc,access-ns = <144>;
+		gpmc,page-burst-access-ns = <24>;
+		gpmc,bus-turnaround-ns = <90>;
+		gpmc,cycle2cycle-delay-ns = <90>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
-		vddvario-supply = <&vddvario_sb_t35>;
-		vdd33a-supply = <&vdd33a_sb_t35>;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
 		reg-io-width = <4>;
 		smsc,save-mac-address;
 	};
diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/omap3-sbc-t3517.dts
index 024c9c6..42189b6 100644
--- a/arch/arm/boot/dts/omap3-sbc-t3517.dts
+++ b/arch/arm/boot/dts/omap3-sbc-t3517.dts
@@ -8,6 +8,19 @@
 / {
 	model = "CompuLab SBC-T3517 with CM-T3517";
 	compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+	/* Only one GPMC smsc9220 on SBC-T3517, CM-T3517 uses am35x Ethernet */
+	vddvario: regulator-vddvario-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a: regulator-vdd33a-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
 };
 
 &omap3_pmx_core {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index acb9019..4231191 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -61,7 +61,7 @@
 			ti,hwmods = "mpu";
 		};
 
-		iva {
+		iva: iva {
 			compatible = "ti,iva2.2";
 			ti,hwmods = "iva";
 
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index f8c9855..36b4312 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -630,6 +630,13 @@
 			status = "disabled";
 		};
 
+		mailbox: mailbox@4a0f4000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x4a0f4000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mailbox";
+		};
+
 		timer1: timer@4ae18000 {
 			compatible = "ti,omap5430-timer";
 			reg = <0x4ae18000 0x80>;
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index eabcfdb..a106b08 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -13,7 +13,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	model = "Atmel SAMA5D3 family SoC";
diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi
index b029fe7..1b02208 100644
--- a/arch/arm/boot/dts/sama5d3_mci2.dtsi
+++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi
@@ -9,7 +9,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	ahb {
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 382b044..0284845 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -9,7 +9,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	aliases {
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index a9fa75e..7a8d4c6 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -9,7 +9,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/clk/at91.h>
+#include <dt-bindings/clock/at91.h>
 
 / {
 	aliases {
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 32efc10..aba1c8a 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -87,7 +87,7 @@
 
 		pll4: clk@01c20018 {
 			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll1-clk";
+			compatible = "allwinner,sun7i-a20-pll4-clk";
 			reg = <0x01c20018 0x4>;
 			clocks = <&osc24M>;
 			clock-output-names = "pll4";
@@ -109,6 +109,14 @@
 			clock-output-names = "pll6_sata", "pll6_other", "pll6";
 		};
 
+		pll8: clk@01c20040 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun7i-a20-pll4-clk";
+			reg = <0x01c20040 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll8";
+		};
+
 		cpu: cpu@01c20054 {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-cpu-clk";
@@ -805,9 +813,9 @@
 			status = "disabled";
 		};
 
-		i2c4: i2c@01c2bc00 {
+		i2c4: i2c@01c2c000 {
 			compatible = "allwinner,sun4i-i2c";
-			reg = <0x01c2bc00 0x400>;
+			reg = <0x01c2c000 0x400>;
 			interrupts = <0 89 4>;
 			clocks = <&apb1_gates 15>;
 			clock-frequency = <100000>;
diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c
index 41bca32..5339009 100644
--- a/arch/arm/common/edma.c
+++ b/arch/arm/common/edma.c
@@ -1423,55 +1423,38 @@
 
 #if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_DMADEVICES)
 
-static int edma_of_read_u32_to_s16_array(const struct device_node *np,
-					 const char *propname, s16 *out_values,
-					 size_t sz)
+static int edma_xbar_event_map(struct device *dev, struct device_node *node,
+			       struct edma_soc_info *pdata, size_t sz)
 {
-	int ret;
-
-	ret = of_property_read_u16_array(np, propname, out_values, sz);
-	if (ret)
-		return ret;
-
-	/* Terminate it */
-	*out_values++ = -1;
-	*out_values++ = -1;
-
-	return 0;
-}
-
-static int edma_xbar_event_map(struct device *dev,
-			       struct device_node *node,
-			       struct edma_soc_info *pdata, int len)
-{
-	int ret, i;
+	const char pname[] = "ti,edma-xbar-event-map";
 	struct resource res;
 	void __iomem *xbar;
-	const s16 (*xbar_chans)[2];
+	s16 (*xbar_chans)[2];
+	size_t nelm = sz / sizeof(s16);
 	u32 shift, offset, mux;
+	int ret, i;
 
-	xbar_chans = devm_kzalloc(dev,
-				  len/sizeof(s16) + 2*sizeof(s16),
-				  GFP_KERNEL);
+	xbar_chans = devm_kzalloc(dev, (nelm + 2) * sizeof(s16), GFP_KERNEL);
 	if (!xbar_chans)
 		return -ENOMEM;
 
 	ret = of_address_to_resource(node, 1, &res);
 	if (ret)
-		return -EIO;
+		return -ENOMEM;
 
 	xbar = devm_ioremap(dev, res.start, resource_size(&res));
 	if (!xbar)
 		return -ENOMEM;
 
-	ret = edma_of_read_u32_to_s16_array(node,
-					    "ti,edma-xbar-event-map",
-					    (s16 *)xbar_chans,
-					    len/sizeof(u32));
+	ret = of_property_read_u16_array(node, pname, (u16 *)xbar_chans, nelm);
 	if (ret)
 		return -EIO;
 
-	for (i = 0; xbar_chans[i][0] != -1; i++) {
+	/* Invalidate last entry for the other user of this mess */
+	nelm >>= 1;
+	xbar_chans[nelm][0] = xbar_chans[nelm][1] = -1;
+
+	for (i = 0; i < nelm; i++) {
 		shift = (xbar_chans[i][1] & 0x03) << 3;
 		offset = xbar_chans[i][1] & 0xfffffffc;
 		mux = readl(xbar + offset);
@@ -1480,8 +1463,7 @@
 		writel(mux, (xbar + offset));
 	}
 
-	pdata->xbar_chans = xbar_chans;
-
+	pdata->xbar_chans = (const s16 (*)[2]) xbar_chans;
 	return 0;
 }
 
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig
index b5df4a5..81ba78e 100644
--- a/arch/arm/configs/sunxi_defconfig
+++ b/arch/arm/configs/sunxi_defconfig
@@ -37,7 +37,7 @@
 # CONFIG_NET_VENDOR_NATSEMI is not set
 # CONFIG_NET_VENDOR_SEEQ is not set
 # CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_STMMAC_ETH=y
 # CONFIG_NET_VENDOR_WIZNET is not set
 # CONFIG_WLAN is not set
 CONFIG_SERIAL_8250=y
diff --git a/arch/arm/mach-omap2/omap-headsmp.S b/arch/arm/mach-omap2/omap-headsmp.S
index 75e9295..40c5d5f 100644
--- a/arch/arm/mach-omap2/omap-headsmp.S
+++ b/arch/arm/mach-omap2/omap-headsmp.S
@@ -1,7 +1,7 @@
 /*
  * Secondary CPU startup routine source file.
  *
- * Copyright (C) 2009 Texas Instruments, Inc.
+ * Copyright (C) 2009-2014 Texas Instruments, Inc.
  *
  * Author:
  *      Santosh Shilimkar <santosh.shilimkar@ti.com>
@@ -28,9 +28,13 @@
  * code.  This routine also provides a holding flag into which
  * secondary core is held until we're ready for it to initialise.
  * The primary core will update this flag using a hardware
-+ * register AuxCoreBoot0.
+ * register AuxCoreBoot0.
  */
 ENTRY(omap5_secondary_startup)
+.arm
+THUMB( adr     r9, BSYM(wait)  )       @ CPU may be entered in ARM mode.
+THUMB( bx      r9              )       @ If this is a Thumb-2 kernel,
+THUMB( .thumb                  )       @ switch to Thumb now.
 wait:	ldr	r2, =AUX_CORE_BOOT0_PA	@ read from AuxCoreBoot0
 	ldr	r0, [r2]
 	mov	r0, r0, lsr #5
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index f565f99..7548db2 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -21,7 +21,7 @@
 #define ORION_MBUS_DEVBUS_BOOT_ATTR   0x0f
 #define ORION_MBUS_DEVBUS_TARGET(cs)  0x01
 #define ORION_MBUS_DEVBUS_ATTR(cs)    (~(1 << cs))
-#define ORION_MBUS_SRAM_TARGET        0x00
+#define ORION_MBUS_SRAM_TARGET        0x09
 #define ORION_MBUS_SRAM_ATTR          0x00
 
 /*
diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c
index 293e2e0..00b7344 100644
--- a/drivers/bus/mvebu-mbus.c
+++ b/drivers/bus/mvebu-mbus.c
@@ -56,6 +56,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/debugfs.h>
+#include <linux/log2.h>
 
 /*
  * DDR target is the same on all platforms.
@@ -222,12 +223,6 @@
 		 */
 		if ((u64)base < wend && end > wbase)
 			return 0;
-
-		/*
-		 * Check if target/attribute conflicts
-		 */
-		if (target == wtarget && attr == wattr)
-			return 0;
 	}
 
 	return 1;
@@ -266,6 +261,17 @@
 		mbus->soc->win_cfg_offset(win);
 	u32 ctrl, remap_addr;
 
+	if (!is_power_of_2(size)) {
+		WARN(true, "Invalid MBus window size: 0x%zx\n", size);
+		return -EINVAL;
+	}
+
+	if ((base & (phys_addr_t)(size - 1)) != 0) {
+		WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base,
+		     size);
+		return -EINVAL;
+	}
+
 	ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
 		(attr << WIN_CTRL_ATTR_SHIFT)    |
 		(target << WIN_CTRL_TGT_SHIFT)   |
@@ -413,6 +419,10 @@
 			   win, (unsigned long long)wbase,
 			   (unsigned long long)(wbase + wsize), wtarget, wattr);
 
+		if (!is_power_of_2(wsize) ||
+		    ((wbase & (u64)(wsize - 1)) != 0))
+			seq_puts(seq, " (Invalid base/size!!)");
+
 		if (win < mbus->soc->num_remappable_wins) {
 			seq_printf(seq, " (remap %016llx)\n",
 				   (unsigned long long)wremap);
diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c
index 110c036..b59a17f 100644
--- a/drivers/memory/mvebu-devbus.c
+++ b/drivers/memory/mvebu-devbus.c
@@ -108,8 +108,19 @@
 			node->full_name);
 		return err;
 	}
-	/* Convert bit width to byte width */
-	r.bus_width /= 8;
+
+	/*
+	 * The bus width is encoded into the register as 0 for 8 bits,
+	 * and 1 for 16 bits, so we do the necessary conversion here.
+	 */
+	if (r.bus_width == 8)
+		r.bus_width = 0;
+	else if (r.bus_width == 16)
+		r.bus_width = 1;
+	else {
+		dev_err(devbus->dev, "invalid bus width %d\n", r.bus_width);
+		return -EINVAL;
+	}
 
 	err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps",
 				 &r.badr_skew);
diff --git a/drivers/pci/host/pci-mvebu.c b/drivers/pci/host/pci-mvebu.c
index d3d1cfd..e384e25 100644
--- a/drivers/pci/host/pci-mvebu.c
+++ b/drivers/pci/host/pci-mvebu.c
@@ -293,6 +293,58 @@
 	return PCIBIOS_SUCCESSFUL;
 }
 
+/*
+ * Remove windows, starting from the largest ones to the smallest
+ * ones.
+ */
+static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port,
+				   phys_addr_t base, size_t size)
+{
+	while (size) {
+		size_t sz = 1 << (fls(size) - 1);
+
+		mvebu_mbus_del_window(base, sz);
+		base += sz;
+		size -= sz;
+	}
+}
+
+/*
+ * MBus windows can only have a power of two size, but PCI BARs do not
+ * have this constraint. Therefore, we have to split the PCI BAR into
+ * areas each having a power of two size. We start from the largest
+ * one (i.e highest order bit set in the size).
+ */
+static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
+				   unsigned int target, unsigned int attribute,
+				   phys_addr_t base, size_t size,
+				   phys_addr_t remap)
+{
+	size_t size_mapped = 0;
+
+	while (size) {
+		size_t sz = 1 << (fls(size) - 1);
+		int ret;
+
+		ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base,
+							sz, remap);
+		if (ret) {
+			dev_err(&port->pcie->pdev->dev,
+				"Could not create MBus window at 0x%x, size 0x%x: %d\n",
+				base, sz, ret);
+			mvebu_pcie_del_windows(port, base - size_mapped,
+					       size_mapped);
+			return;
+		}
+
+		size -= sz;
+		size_mapped += sz;
+		base += sz;
+		if (remap != MVEBU_MBUS_NO_REMAP)
+			remap += sz;
+	}
+}
+
 static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 {
 	phys_addr_t iobase;
@@ -304,8 +356,8 @@
 
 		/* If a window was configured, remove it */
 		if (port->iowin_base) {
-			mvebu_mbus_del_window(port->iowin_base,
-					      port->iowin_size);
+			mvebu_pcie_del_windows(port, port->iowin_base,
+					       port->iowin_size);
 			port->iowin_base = 0;
 			port->iowin_size = 0;
 		}
@@ -331,11 +383,11 @@
 	port->iowin_base = port->pcie->io.start + iobase;
 	port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) |
 			    (port->bridge.iolimitupper << 16)) -
-			    iobase);
+			    iobase) + 1;
 
-	mvebu_mbus_add_window_remap_by_id(port->io_target, port->io_attr,
-					  port->iowin_base, port->iowin_size,
-					  iobase);
+	mvebu_pcie_add_windows(port, port->io_target, port->io_attr,
+			       port->iowin_base, port->iowin_size,
+			       iobase);
 }
 
 static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
@@ -346,8 +398,8 @@
 
 		/* If a window was configured, remove it */
 		if (port->memwin_base) {
-			mvebu_mbus_del_window(port->memwin_base,
-					      port->memwin_size);
+			mvebu_pcie_del_windows(port, port->memwin_base,
+					       port->memwin_size);
 			port->memwin_base = 0;
 			port->memwin_size = 0;
 		}
@@ -364,10 +416,11 @@
 	port->memwin_base  = ((port->bridge.membase & 0xFFF0) << 16);
 	port->memwin_size  =
 		(((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) -
-		port->memwin_base;
+		port->memwin_base + 1;
 
-	mvebu_mbus_add_window_by_id(port->mem_target, port->mem_attr,
-				    port->memwin_base, port->memwin_size);
+	mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr,
+			       port->memwin_base, port->memwin_size,
+			       MVEBU_MBUS_NO_REMAP);
 }
 
 /*
@@ -743,14 +796,21 @@
 
 	/*
 	 * On the PCI-to-PCI bridge side, the I/O windows must have at
-	 * least a 64 KB size and be aligned on their size, and the
-	 * memory windows must have at least a 1 MB size and be
-	 * aligned on their size
+	 * least a 64 KB size and the memory windows must have at
+	 * least a 1 MB size. Moreover, MBus windows need to have a
+	 * base address aligned on their size, and their size must be
+	 * a power of two. This means that if the BAR doesn't have a
+	 * power of two size, several MBus windows will actually be
+	 * created. We need to ensure that the biggest MBus window
+	 * (which will be the first one) is aligned on its size, which
+	 * explains the rounddown_pow_of_two() being done here.
 	 */
 	if (res->flags & IORESOURCE_IO)
-		return round_up(start, max_t(resource_size_t, SZ_64K, size));
+		return round_up(start, max_t(resource_size_t, SZ_64K,
+					     rounddown_pow_of_two(size)));
 	else if (res->flags & IORESOURCE_MEM)
-		return round_up(start, max_t(resource_size_t, SZ_1M, size));
+		return round_up(start, max_t(resource_size_t, SZ_1M,
+					     rounddown_pow_of_two(size)));
 	else
 		return start;
 }
diff --git a/include/dt-bindings/clk/at91.h b/include/dt-bindings/clock/at91.h
similarity index 100%
rename from include/dt-bindings/clk/at91.h
rename to include/dt-bindings/clock/at91.h