| # STK1000 customization |
| |
| if BOARD_ATSTK1000 |
| |
| choice |
| prompt "ATSTK1000 CPU daughterboard type" |
| default BOARD_ATSTK1002 |
| |
| config BOARD_ATSTK1002 |
| bool "ATSTK1002" |
| select CPU_AT32AP7000 |
| |
| config BOARD_ATSTK1003 |
| bool "ATSTK1003" |
| select CPU_AT32AP7001 |
| |
| config BOARD_ATSTK1004 |
| bool "ATSTK1004" |
| select CPU_AT32AP7002 |
| |
| config BOARD_ATSTK1006 |
| bool "ATSTK1006" |
| select CPU_AT32AP7000 |
| |
| endchoice |
| |
| |
| config BOARD_ATSTK100X_CUSTOM |
| bool "Non-default STK1002/STK1003/STK1004 jumper settings" |
| help |
| You will normally leave the jumpers on the CPU card at their |
| default settings. If you need to use certain peripherals, |
| you will need to change some of those jumpers. |
| |
| if BOARD_ATSTK100X_CUSTOM |
| |
| config BOARD_ATSTK100X_SW1_CUSTOM |
| bool "SW1: use SSC1 (not SPI0)" |
| help |
| This also prevents using the external DAC as an audio interface, |
| and means you can't initialize the on-board QVGA display. |
| |
| config BOARD_ATSTK100X_SW2_CUSTOM |
| bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)" |
| help |
| If you change this you'll want an updated boot loader putting |
| the console on UART-C not UART-A. |
| |
| config BOARD_ATSTK100X_SW3_CUSTOM |
| bool "SW3: use TIMER1 (not SSC0 and GCLK)" |
| help |
| This also prevents using the external DAC as an audio interface. |
| |
| config BOARD_ATSTK100X_SW4_CUSTOM |
| bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)" |
| help |
| To use the camera interface you'll need a custom card (on the |
| PCI-format connector) connect a video sensor. |
| |
| config BOARD_ATSTK1002_SW5_CUSTOM |
| bool "SW5: use MACB1 (not LCDC)" |
| depends on BOARD_ATSTK1002 |
| |
| config BOARD_ATSTK1002_SW6_CUSTOM |
| bool "SW6: more GPIOs (not MACB0)" |
| depends on BOARD_ATSTK1002 |
| |
| endif # custom |
| |
| config BOARD_ATSTK100X_SPI1 |
| bool "Configure SPI1 controller" |
| depends on !BOARD_ATSTK100X_SW4_CUSTOM |
| help |
| All the signals for the second SPI controller are available on |
| GPIO lines and accessed through the J1 jumper block. Say "y" |
| here to configure that SPI controller. |
| |
| config BOARD_ATSTK1000_J2_LED |
| bool |
| default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB |
| |
| choice |
| prompt "LEDs connected to J2:" |
| depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM |
| optional |
| help |
| Select this if you have jumpered the J2 jumper block to the |
| LED0..LED7 amber leds, or to the RGB leds, using a ten-pin |
| IDC cable. A default "heartbeat" trigger is provided, but |
| you can of course override this. |
| |
| config BOARD_ATSTK1000_J2_LED8 |
| bool "LED0..LED7" |
| help |
| Select this if J2 is jumpered to LED0..LED7 amber leds. |
| |
| config BOARD_ATSTK1000_J2_RGB |
| bool "RGB leds" |
| help |
| Select this if J2 is jumpered to the RGB leds. |
| |
| endchoice |
| |
| config BOARD_ATSTK1000_EXTDAC |
| bool |
| depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM |
| default y |
| |
| endif # stk 1000 |
