| #ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED |
| #define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED |
| |
| /* |
| * DICE device interface definitions |
| */ |
| |
| /* |
| * Generally, all registers can be read like memory, i.e., with quadlet read or |
| * block read transactions with at least quadlet-aligned offset and length. |
| * Writes are not allowed except where noted; quadlet-sized registers must be |
| * written with a quadlet write transaction. |
| * |
| * All values are in big endian. The DICE firmware runs on a little-endian CPU |
| * and just byte-swaps _all_ quadlets on the bus, so values without endianness |
| * (e.g. strings) get scrambled and must be byte-swapped again by the driver. |
| */ |
| |
| /* |
| * Streaming is handled by the "DICE driver" interface. Its registers are |
| * located in this private address space. |
| */ |
| #define DICE_PRIVATE_SPACE 0xffffe0000000uLL |
| |
| /* |
| * The registers are organized in several sections, which are organized |
| * separately to allow them to be extended individually. Whether a register is |
| * supported can be detected by checking its offset against its section's size. |
| * |
| * The section offset values are relative to DICE_PRIVATE_SPACE; the offset/ |
| * size values are measured in quadlets. Read-only. |
| */ |
| #define DICE_GLOBAL_OFFSET 0x00 |
| #define DICE_GLOBAL_SIZE 0x04 |
| #define DICE_TX_OFFSET 0x08 |
| #define DICE_TX_SIZE 0x0c |
| #define DICE_RX_OFFSET 0x10 |
| #define DICE_RX_SIZE 0x14 |
| #define DICE_EXT_SYNC_OFFSET 0x18 |
| #define DICE_EXT_SYNC_SIZE 0x1c |
| #define DICE_UNUSED2_OFFSET 0x20 |
| #define DICE_UNUSED2_SIZE 0x24 |
| |
| /* |
| * Global settings. |
| */ |
| |
| /* |
| * Stores the full 64-bit address (node ID and offset in the node's address |
| * space) where the device will send notifications. Must be changed with |
| * a compare/swap transaction by the owner. This register is automatically |
| * cleared on a bus reset. |
| */ |
| #define GLOBAL_OWNER 0x000 |
| #define OWNER_NO_OWNER 0xffff000000000000uLL |
| #define OWNER_NODE_SHIFT 48 |
| |
| /* |
| * A bitmask with asynchronous events; read-only. When any event(s) happen, |
| * the bits of previous events are cleared, and the value of this register is |
| * also written to the address stored in the owner register. |
| */ |
| #define GLOBAL_NOTIFICATION 0x008 |
| /* Some registers in the Rx/Tx sections may have changed. */ |
| #define NOTIFY_RX_CFG_CHG 0x00000001 |
| #define NOTIFY_TX_CFG_CHG 0x00000002 |
| /* Lock status of the current clock source may have changed. */ |
| #define NOTIFY_LOCK_CHG 0x00000010 |
| /* Write to the clock select register has been finished. */ |
| #define NOTIFY_CLOCK_ACCEPTED 0x00000020 |
| /* Lock status of some clock source has changed. */ |
| #define NOTIFY_EXT_STATUS 0x00000040 |
| /* Other bits may be used for device-specific events. */ |
| |
| /* |
| * A name that can be customized for each device; read/write. Padded with zero |
| * bytes. Quadlets are byte-swapped. The encoding is whatever the host driver |
| * happens to be using. |
| */ |
| #define GLOBAL_NICK_NAME 0x00c |
| #define NICK_NAME_SIZE 64 |
| |
| /* |
| * The current sample rate and clock source; read/write. Whether a clock |
| * source or sample rate is supported is device-specific; the internal clock |
| * source is always available. Low/mid/high = up to 48/96/192 kHz. This |
| * register can be changed even while streams are running. |
| */ |
| #define GLOBAL_CLOCK_SELECT 0x04c |
| #define CLOCK_SOURCE_MASK 0x000000ff |
| #define CLOCK_SOURCE_AES1 0x00000000 |
| #define CLOCK_SOURCE_AES2 0x00000001 |
| #define CLOCK_SOURCE_AES3 0x00000002 |
| #define CLOCK_SOURCE_AES4 0x00000003 |
| #define CLOCK_SOURCE_AES_ANY 0x00000004 |
| #define CLOCK_SOURCE_ADAT 0x00000005 |
| #define CLOCK_SOURCE_TDIF 0x00000006 |
| #define CLOCK_SOURCE_WC 0x00000007 |
| #define CLOCK_SOURCE_ARX1 0x00000008 |
| #define CLOCK_SOURCE_ARX2 0x00000009 |
| #define CLOCK_SOURCE_ARX3 0x0000000a |
| #define CLOCK_SOURCE_ARX4 0x0000000b |
| #define CLOCK_SOURCE_INTERNAL 0x0000000c |
| #define CLOCK_RATE_MASK 0x0000ff00 |
| #define CLOCK_RATE_32000 0x00000000 |
| #define CLOCK_RATE_44100 0x00000100 |
| #define CLOCK_RATE_48000 0x00000200 |
| #define CLOCK_RATE_88200 0x00000300 |
| #define CLOCK_RATE_96000 0x00000400 |
| #define CLOCK_RATE_176400 0x00000500 |
| #define CLOCK_RATE_192000 0x00000600 |
| #define CLOCK_RATE_ANY_LOW 0x00000700 |
| #define CLOCK_RATE_ANY_MID 0x00000800 |
| #define CLOCK_RATE_ANY_HIGH 0x00000900 |
| #define CLOCK_RATE_NONE 0x00000a00 |
| #define CLOCK_RATE_SHIFT 8 |
| |
| /* |
| * Enable streaming; read/write. Writing a non-zero value (re)starts all |
| * streams that have a valid iso channel set; zero stops all streams. The |
| * streams' parameters must be configured before starting. This register is |
| * automatically cleared on a bus reset. |
| */ |
| #define GLOBAL_ENABLE 0x050 |
| |
| /* |
| * Status of the sample clock; read-only. |
| */ |
| #define GLOBAL_STATUS 0x054 |
| /* The current clock source is locked. */ |
| #define STATUS_SOURCE_LOCKED 0x00000001 |
| /* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */ |
| #define STATUS_NOMINAL_RATE_MASK 0x0000ff00 |
| |
| /* |
| * Status of all clock sources; read-only. |
| */ |
| #define GLOBAL_EXTENDED_STATUS 0x058 |
| /* |
| * The _LOCKED bits always show the current status; any change generates |
| * a notification. |
| */ |
| #define EXT_STATUS_AES1_LOCKED 0x00000001 |
| #define EXT_STATUS_AES2_LOCKED 0x00000002 |
| #define EXT_STATUS_AES3_LOCKED 0x00000004 |
| #define EXT_STATUS_AES4_LOCKED 0x00000008 |
| #define EXT_STATUS_ADAT_LOCKED 0x00000010 |
| #define EXT_STATUS_TDIF_LOCKED 0x00000020 |
| #define EXT_STATUS_ARX1_LOCKED 0x00000040 |
| #define EXT_STATUS_ARX2_LOCKED 0x00000080 |
| #define EXT_STATUS_ARX3_LOCKED 0x00000100 |
| #define EXT_STATUS_ARX4_LOCKED 0x00000200 |
| #define EXT_STATUS_WC_LOCKED 0x00000400 |
| /* |
| * The _SLIP bits do not generate notifications; a set bit indicates that an |
| * error occurred since the last time when this register was read with |
| * a quadlet read transaction. |
| */ |
| #define EXT_STATUS_AES1_SLIP 0x00010000 |
| #define EXT_STATUS_AES2_SLIP 0x00020000 |
| #define EXT_STATUS_AES3_SLIP 0x00040000 |
| #define EXT_STATUS_AES4_SLIP 0x00080000 |
| #define EXT_STATUS_ADAT_SLIP 0x00100000 |
| #define EXT_STATUS_TDIF_SLIP 0x00200000 |
| #define EXT_STATUS_ARX1_SLIP 0x00400000 |
| #define EXT_STATUS_ARX2_SLIP 0x00800000 |
| #define EXT_STATUS_ARX3_SLIP 0x01000000 |
| #define EXT_STATUS_ARX4_SLIP 0x02000000 |
| #define EXT_STATUS_WC_SLIP 0x04000000 |
| |
| /* |
| * The measured rate of the current clock source, in Hz; read-only. |
| */ |
| #define GLOBAL_SAMPLE_RATE 0x05c |
| |
| /* |
| * The version of the DICE driver specification that this device conforms to; |
| * read-only. |
| */ |
| #define GLOBAL_VERSION 0x060 |
| |
| /* Some old firmware versions do not have the following global registers: */ |
| |
| /* |
| * Supported sample rates and clock sources; read-only. |
| */ |
| #define GLOBAL_CLOCK_CAPABILITIES 0x064 |
| #define CLOCK_CAP_RATE_32000 0x00000001 |
| #define CLOCK_CAP_RATE_44100 0x00000002 |
| #define CLOCK_CAP_RATE_48000 0x00000004 |
| #define CLOCK_CAP_RATE_88200 0x00000008 |
| #define CLOCK_CAP_RATE_96000 0x00000010 |
| #define CLOCK_CAP_RATE_176400 0x00000020 |
| #define CLOCK_CAP_RATE_192000 0x00000040 |
| #define CLOCK_CAP_SOURCE_AES1 0x00010000 |
| #define CLOCK_CAP_SOURCE_AES2 0x00020000 |
| #define CLOCK_CAP_SOURCE_AES3 0x00040000 |
| #define CLOCK_CAP_SOURCE_AES4 0x00080000 |
| #define CLOCK_CAP_SOURCE_AES_ANY 0x00100000 |
| #define CLOCK_CAP_SOURCE_ADAT 0x00200000 |
| #define CLOCK_CAP_SOURCE_TDIF 0x00400000 |
| #define CLOCK_CAP_SOURCE_WC 0x00800000 |
| #define CLOCK_CAP_SOURCE_ARX1 0x01000000 |
| #define CLOCK_CAP_SOURCE_ARX2 0x02000000 |
| #define CLOCK_CAP_SOURCE_ARX3 0x04000000 |
| #define CLOCK_CAP_SOURCE_ARX4 0x08000000 |
| #define CLOCK_CAP_SOURCE_INTERNAL 0x10000000 |
| |
| /* |
| * Names of all clock sources; read-only. Quadlets are byte-swapped. Names |
| * are separated with one backslash, the list is terminated with two |
| * backslashes. Unused clock sources are included. |
| */ |
| #define GLOBAL_CLOCK_SOURCE_NAMES 0x068 |
| #define CLOCK_SOURCE_NAMES_SIZE 256 |
| |
| /* |
| * Capture stream settings. This section includes the number/size registers |
| * and the registers of all streams. |
| */ |
| |
| /* |
| * The number of supported capture streams; read-only. |
| */ |
| #define TX_NUMBER 0x000 |
| |
| /* |
| * The size of one stream's register block, in quadlets; read-only. The |
| * registers of the first stream follow immediately afterwards; the registers |
| * of the following streams are offset by this register's value. |
| */ |
| #define TX_SIZE 0x004 |
| |
| /* |
| * The isochronous channel number on which packets are sent, or -1 if the |
| * stream is not to be used; read/write. |
| */ |
| #define TX_ISOCHRONOUS 0x008 |
| |
| /* |
| * The number of audio channels; read-only. There will be one quadlet per |
| * channel; the first channel is the first quadlet in a data block. |
| */ |
| #define TX_NUMBER_AUDIO 0x00c |
| |
| /* |
| * The number of MIDI ports, 0-8; read-only. If > 0, there will be one |
| * additional quadlet in each data block, following the audio quadlets. |
| */ |
| #define TX_NUMBER_MIDI 0x010 |
| |
| /* |
| * The speed at which the packets are sent, SCODE_100-_400; read/write. |
| */ |
| #define TX_SPEED 0x014 |
| |
| /* |
| * Names of all audio channels; read-only. Quadlets are byte-swapped. Names |
| * are separated with one backslash, the list is terminated with two |
| * backslashes. |
| */ |
| #define TX_NAMES 0x018 |
| #define TX_NAMES_SIZE 256 |
| |
| /* |
| * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio |
| * channel. |
| */ |
| #define TX_AC3_CAPABILITIES 0x118 |
| |
| /* |
| * Send audio data with IEC60958 label; read/write. Bitmask with one bit per |
| * audio channel. This register can be changed even while the stream is |
| * running. |
| */ |
| #define TX_AC3_ENABLE 0x11c |
| |
| /* |
| * Playback stream settings. This section includes the number/size registers |
| * and the registers of all streams. |
| */ |
| |
| /* |
| * The number of supported playback streams; read-only. |
| */ |
| #define RX_NUMBER 0x000 |
| |
| /* |
| * The size of one stream's register block, in quadlets; read-only. The |
| * registers of the first stream follow immediately afterwards; the registers |
| * of the following streams are offset by this register's value. |
| */ |
| #define RX_SIZE 0x004 |
| |
| /* |
| * The isochronous channel number on which packets are received, or -1 if the |
| * stream is not to be used; read/write. |
| */ |
| #define RX_ISOCHRONOUS 0x008 |
| |
| /* |
| * Index of first quadlet to be interpreted; read/write. If > 0, that many |
| * quadlets at the beginning of each data block will be ignored, and all the |
| * audio and MIDI quadlets will follow. |
| */ |
| #define RX_SEQ_START 0x00c |
| |
| /* |
| * The number of audio channels; read-only. There will be one quadlet per |
| * channel. |
| */ |
| #define RX_NUMBER_AUDIO 0x010 |
| |
| /* |
| * The number of MIDI ports, 0-8; read-only. If > 0, there will be one |
| * additional quadlet in each data block, following the audio quadlets. |
| */ |
| #define RX_NUMBER_MIDI 0x014 |
| |
| /* |
| * Names of all audio channels; read-only. Quadlets are byte-swapped. Names |
| * are separated with one backslash, the list is terminated with two |
| * backslashes. |
| */ |
| #define RX_NAMES 0x018 |
| #define RX_NAMES_SIZE 256 |
| |
| /* |
| * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio |
| * channel. |
| */ |
| #define RX_AC3_CAPABILITIES 0x118 |
| |
| /* |
| * Receive audio data with IEC60958 label; read/write. Bitmask with one bit |
| * per audio channel. This register can be changed even while the stream is |
| * running. |
| */ |
| #define RX_AC3_ENABLE 0x11c |
| |
| /* |
| * Extended synchronization information. |
| * This section can be read completely with a block read request. |
| */ |
| |
| /* |
| * Current clock source; read-only. |
| */ |
| #define EXT_SYNC_CLOCK_SOURCE 0x000 |
| |
| /* |
| * Clock source is locked (boolean); read-only. |
| */ |
| #define EXT_SYNC_LOCKED 0x004 |
| |
| /* |
| * Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or |
| * _NONE; read-only. |
| */ |
| #define EXT_SYNC_RATE 0x008 |
| |
| /* |
| * ADAT user data bits; read-only. |
| */ |
| #define EXT_SYNC_ADAT_USER_DATA 0x00c |
| /* The data bits, if available. */ |
| #define ADAT_USER_DATA_MASK 0x0f |
| /* The data bits are not available. */ |
| #define ADAT_USER_DATA_NO_DATA 0x10 |
| |
| #endif |
