| /* | |
| * Copyright 2004-2009 Analog Devices Inc. | |
| * 2008-2009 Bluetechnix | |
| * 2005 National ICT Australia (NICTA) | |
| * Aidan Williams <aidan@nicta.com.au> | |
| * | |
| * Licensed under the GPL-2 or later. | |
| */ | |
| #include <linux/device.h> | |
| #include <linux/etherdevice.h> | |
| #include <linux/export.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/mtd/mtd.h> | |
| #include <linux/mtd/partitions.h> | |
| #include <linux/mtd/physmap.h> | |
| #include <linux/spi/spi.h> | |
| #include <linux/spi/flash.h> | |
| #if IS_ENABLED(CONFIG_USB_ISP1362_HCD) | |
| #include <linux/usb/isp1362.h> | |
| #endif | |
| #include <linux/ata_platform.h> | |
| #include <linux/irq.h> | |
| #include <linux/gpio.h> | |
| #include <asm/dma.h> | |
| #include <asm/bfin5xx_spi.h> | |
| #include <asm/portmux.h> | |
| #include <asm/dpmc.h> | |
| #include <linux/spi/mmc_spi.h> | |
| /* | |
| * Name the Board for the /proc/cpuinfo | |
| */ | |
| const char bfin_board_name[] = "Bluetechnix CM BF537U"; | |
| #if IS_ENABLED(CONFIG_SPI_BFIN5XX) | |
| /* all SPI peripherals info goes here */ | |
| #if IS_ENABLED(CONFIG_MTD_M25P80) | |
| static struct mtd_partition bfin_spi_flash_partitions[] = { | |
| { | |
| .name = "bootloader(spi)", | |
| .size = 0x00020000, | |
| .offset = 0, | |
| .mask_flags = MTD_CAP_ROM | |
| }, { | |
| .name = "linux kernel(spi)", | |
| .size = 0xe0000, | |
| .offset = 0x20000 | |
| }, { | |
| .name = "file system(spi)", | |
| .size = 0x700000, | |
| .offset = 0x00100000, | |
| } | |
| }; | |
| static struct flash_platform_data bfin_spi_flash_data = { | |
| .name = "m25p80", | |
| .parts = bfin_spi_flash_partitions, | |
| .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), | |
| .type = "m25p64", | |
| }; | |
| /* SPI flash chip (m25p64) */ | |
| static struct bfin5xx_spi_chip spi_flash_chip_info = { | |
| .enable_dma = 0, /* use dma transfer with this chip*/ | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_MMC_SPI) | |
| static struct bfin5xx_spi_chip mmc_spi_chip_info = { | |
| .enable_dma = 0, | |
| }; | |
| #endif | |
| static struct spi_board_info bfin_spi_board_info[] __initdata = { | |
| #if IS_ENABLED(CONFIG_MTD_M25P80) | |
| { | |
| /* the modalias must be the same as spi device driver name */ | |
| .modalias = "m25p80", /* Name of spi_driver for this device */ | |
| .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ | |
| .bus_num = 0, /* Framework bus number */ | |
| .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ | |
| .platform_data = &bfin_spi_flash_data, | |
| .controller_data = &spi_flash_chip_info, | |
| .mode = SPI_MODE_3, | |
| }, | |
| #endif | |
| #if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X) | |
| { | |
| .modalias = "ad183x", | |
| .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ | |
| .bus_num = 0, | |
| .chip_select = 4, | |
| }, | |
| #endif | |
| #if IS_ENABLED(CONFIG_MMC_SPI) | |
| { | |
| .modalias = "mmc_spi", | |
| .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ | |
| .bus_num = 0, | |
| .chip_select = 1, | |
| .controller_data = &mmc_spi_chip_info, | |
| .mode = SPI_MODE_3, | |
| }, | |
| #endif | |
| }; | |
| /* SPI (0) */ | |
| static struct resource bfin_spi0_resource[] = { | |
| [0] = { | |
| .start = SPI0_REGBASE, | |
| .end = SPI0_REGBASE + 0xFF, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| [1] = { | |
| .start = CH_SPI, | |
| .end = CH_SPI, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| [2] = { | |
| .start = IRQ_SPI, | |
| .end = IRQ_SPI, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| /* SPI controller data */ | |
| static struct bfin5xx_spi_master bfin_spi0_info = { | |
| .num_chipselect = 8, | |
| .enable_dma = 1, /* master has the ability to do dma transfer */ | |
| .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, | |
| }; | |
| static struct platform_device bfin_spi0_device = { | |
| .name = "bfin-spi", | |
| .id = 0, /* Bus number */ | |
| .num_resources = ARRAY_SIZE(bfin_spi0_resource), | |
| .resource = bfin_spi0_resource, | |
| .dev = { | |
| .platform_data = &bfin_spi0_info, /* Passed to driver */ | |
| }, | |
| }; | |
| #endif /* spi master and devices */ | |
| #if IS_ENABLED(CONFIG_RTC_DRV_BFIN) | |
| static struct platform_device rtc_device = { | |
| .name = "rtc-bfin", | |
| .id = -1, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_FB_HITACHI_TX09) | |
| static struct platform_device hitachi_fb_device = { | |
| .name = "hitachi-tx09", | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_SMC91X) | |
| #include <linux/smc91x.h> | |
| static struct smc91x_platdata smc91x_info = { | |
| .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, | |
| .leda = RPC_LED_100_10, | |
| .ledb = RPC_LED_TX_RX, | |
| }; | |
| static struct resource smc91x_resources[] = { | |
| { | |
| .start = 0x20200300, | |
| .end = 0x20200300 + 16, | |
| .flags = IORESOURCE_MEM, | |
| }, { | |
| .start = IRQ_PF14, | |
| .end = IRQ_PF14, | |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, | |
| }, | |
| }; | |
| static struct platform_device smc91x_device = { | |
| .name = "smc91x", | |
| .id = 0, | |
| .num_resources = ARRAY_SIZE(smc91x_resources), | |
| .resource = smc91x_resources, | |
| .dev = { | |
| .platform_data = &smc91x_info, | |
| }, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_USB_ISP1362_HCD) | |
| static struct resource isp1362_hcd_resources[] = { | |
| { | |
| .start = 0x20308000, | |
| .end = 0x20308000, | |
| .flags = IORESOURCE_MEM, | |
| }, { | |
| .start = 0x20308004, | |
| .end = 0x20308004, | |
| .flags = IORESOURCE_MEM, | |
| }, { | |
| .start = IRQ_PG15, | |
| .end = IRQ_PG15, | |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, | |
| }, | |
| }; | |
| static struct isp1362_platform_data isp1362_priv = { | |
| .sel15Kres = 1, | |
| .clknotstop = 0, | |
| .oc_enable = 0, | |
| .int_act_high = 0, | |
| .int_edge_triggered = 0, | |
| .remote_wakeup_connected = 0, | |
| .no_power_switching = 1, | |
| .power_switching_mode = 0, | |
| }; | |
| static struct platform_device isp1362_hcd_device = { | |
| .name = "isp1362-hcd", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &isp1362_priv, | |
| }, | |
| .num_resources = ARRAY_SIZE(isp1362_hcd_resources), | |
| .resource = isp1362_hcd_resources, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_USB_NET2272) | |
| static struct resource net2272_bfin_resources[] = { | |
| { | |
| .start = 0x20200000, | |
| .end = 0x20200000 + 0x100, | |
| .flags = IORESOURCE_MEM, | |
| }, { | |
| .start = IRQ_PH14, | |
| .end = IRQ_PH14, | |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, | |
| }, | |
| }; | |
| static struct platform_device net2272_bfin_device = { | |
| .name = "net2272", | |
| .id = -1, | |
| .num_resources = ARRAY_SIZE(net2272_bfin_resources), | |
| .resource = net2272_bfin_resources, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_MTD_GPIO_ADDR) | |
| static struct mtd_partition cm_partitions[] = { | |
| { | |
| .name = "bootloader(nor)", | |
| .size = 0x40000, | |
| .offset = 0, | |
| }, { | |
| .name = "linux kernel(nor)", | |
| .size = 0x100000, | |
| .offset = MTDPART_OFS_APPEND, | |
| }, { | |
| .name = "file system(nor)", | |
| .size = MTDPART_SIZ_FULL, | |
| .offset = MTDPART_OFS_APPEND, | |
| } | |
| }; | |
| static struct physmap_flash_data cm_flash_data = { | |
| .width = 2, | |
| .parts = cm_partitions, | |
| .nr_parts = ARRAY_SIZE(cm_partitions), | |
| }; | |
| static unsigned cm_flash_gpios[] = { GPIO_PH0 }; | |
| static struct resource cm_flash_resource[] = { | |
| { | |
| .name = "cfi_probe", | |
| .start = 0x20000000, | |
| .end = 0x201fffff, | |
| .flags = IORESOURCE_MEM, | |
| }, { | |
| .start = (unsigned long)cm_flash_gpios, | |
| .end = ARRAY_SIZE(cm_flash_gpios), | |
| .flags = IORESOURCE_IRQ, | |
| } | |
| }; | |
| static struct platform_device cm_flash_device = { | |
| .name = "gpio-addr-flash", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &cm_flash_data, | |
| }, | |
| .num_resources = ARRAY_SIZE(cm_flash_resource), | |
| .resource = cm_flash_resource, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_SERIAL_BFIN) | |
| #ifdef CONFIG_SERIAL_BFIN_UART0 | |
| static struct resource bfin_uart0_resources[] = { | |
| { | |
| .start = UART0_THR, | |
| .end = UART0_GCTL+2, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = IRQ_UART0_TX, | |
| .end = IRQ_UART0_TX, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = IRQ_UART0_RX, | |
| .end = IRQ_UART0_RX, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = IRQ_UART0_ERROR, | |
| .end = IRQ_UART0_ERROR, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = CH_UART0_TX, | |
| .end = CH_UART0_TX, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| { | |
| .start = CH_UART0_RX, | |
| .end = CH_UART0_RX, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| }; | |
| static unsigned short bfin_uart0_peripherals[] = { | |
| P_UART0_TX, P_UART0_RX, 0 | |
| }; | |
| static struct platform_device bfin_uart0_device = { | |
| .name = "bfin-uart", | |
| .id = 0, | |
| .num_resources = ARRAY_SIZE(bfin_uart0_resources), | |
| .resource = bfin_uart0_resources, | |
| .dev = { | |
| .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ | |
| }, | |
| }; | |
| #endif | |
| #ifdef CONFIG_SERIAL_BFIN_UART1 | |
| static struct resource bfin_uart1_resources[] = { | |
| { | |
| .start = UART1_THR, | |
| .end = UART1_GCTL+2, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = IRQ_UART1_TX, | |
| .end = IRQ_UART1_TX, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = IRQ_UART1_RX, | |
| .end = IRQ_UART1_RX, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = IRQ_UART1_ERROR, | |
| .end = IRQ_UART1_ERROR, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = CH_UART1_TX, | |
| .end = CH_UART1_TX, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| { | |
| .start = CH_UART1_RX, | |
| .end = CH_UART1_RX, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| }; | |
| static unsigned short bfin_uart1_peripherals[] = { | |
| P_UART1_TX, P_UART1_RX, 0 | |
| }; | |
| static struct platform_device bfin_uart1_device = { | |
| .name = "bfin-uart", | |
| .id = 1, | |
| .num_resources = ARRAY_SIZE(bfin_uart1_resources), | |
| .resource = bfin_uart1_resources, | |
| .dev = { | |
| .platform_data = &bfin_uart1_peripherals, /* Passed to driver */ | |
| }, | |
| }; | |
| #endif | |
| #endif | |
| #if IS_ENABLED(CONFIG_BFIN_SIR) | |
| #ifdef CONFIG_BFIN_SIR0 | |
| static struct resource bfin_sir0_resources[] = { | |
| { | |
| .start = 0xFFC00400, | |
| .end = 0xFFC004FF, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = IRQ_UART0_RX, | |
| .end = IRQ_UART0_RX+1, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = CH_UART0_RX, | |
| .end = CH_UART0_RX+1, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| }; | |
| static struct platform_device bfin_sir0_device = { | |
| .name = "bfin_sir", | |
| .id = 0, | |
| .num_resources = ARRAY_SIZE(bfin_sir0_resources), | |
| .resource = bfin_sir0_resources, | |
| }; | |
| #endif | |
| #ifdef CONFIG_BFIN_SIR1 | |
| static struct resource bfin_sir1_resources[] = { | |
| { | |
| .start = 0xFFC02000, | |
| .end = 0xFFC020FF, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = IRQ_UART1_RX, | |
| .end = IRQ_UART1_RX+1, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = CH_UART1_RX, | |
| .end = CH_UART1_RX+1, | |
| .flags = IORESOURCE_DMA, | |
| }, | |
| }; | |
| static struct platform_device bfin_sir1_device = { | |
| .name = "bfin_sir", | |
| .id = 1, | |
| .num_resources = ARRAY_SIZE(bfin_sir1_resources), | |
| .resource = bfin_sir1_resources, | |
| }; | |
| #endif | |
| #endif | |
| #if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI) | |
| static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0}; | |
| static struct resource bfin_twi0_resource[] = { | |
| [0] = { | |
| .start = TWI0_REGBASE, | |
| .end = TWI0_REGBASE, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| [1] = { | |
| .start = IRQ_TWI, | |
| .end = IRQ_TWI, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static struct platform_device i2c_bfin_twi_device = { | |
| .name = "i2c-bfin-twi", | |
| .id = 0, | |
| .num_resources = ARRAY_SIZE(bfin_twi0_resource), | |
| .resource = bfin_twi0_resource, | |
| .dev = { | |
| .platform_data = &bfin_twi0_pins, | |
| }, | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) | |
| #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART | |
| static struct resource bfin_sport0_uart_resources[] = { | |
| { | |
| .start = SPORT0_TCR1, | |
| .end = SPORT0_MRCS3+4, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = IRQ_SPORT0_RX, | |
| .end = IRQ_SPORT0_RX+1, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = IRQ_SPORT0_ERROR, | |
| .end = IRQ_SPORT0_ERROR, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static unsigned short bfin_sport0_peripherals[] = { | |
| P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS, | |
| P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0 | |
| }; | |
| static struct platform_device bfin_sport0_uart_device = { | |
| .name = "bfin-sport-uart", | |
| .id = 0, | |
| .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources), | |
| .resource = bfin_sport0_uart_resources, | |
| .dev = { | |
| .platform_data = &bfin_sport0_peripherals, /* Passed to driver */ | |
| }, | |
| }; | |
| #endif | |
| #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART | |
| static struct resource bfin_sport1_uart_resources[] = { | |
| { | |
| .start = SPORT1_TCR1, | |
| .end = SPORT1_MRCS3+4, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = IRQ_SPORT1_RX, | |
| .end = IRQ_SPORT1_RX+1, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| { | |
| .start = IRQ_SPORT1_ERROR, | |
| .end = IRQ_SPORT1_ERROR, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static unsigned short bfin_sport1_peripherals[] = { | |
| P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS, | |
| P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0 | |
| }; | |
| static struct platform_device bfin_sport1_uart_device = { | |
| .name = "bfin-sport-uart", | |
| .id = 1, | |
| .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources), | |
| .resource = bfin_sport1_uart_resources, | |
| .dev = { | |
| .platform_data = &bfin_sport1_peripherals, /* Passed to driver */ | |
| }, | |
| }; | |
| #endif | |
| #endif | |
| #if IS_ENABLED(CONFIG_BFIN_MAC) | |
| #include <linux/bfin_mac.h> | |
| static const unsigned short bfin_mac_peripherals[] = P_MII0; | |
| static struct bfin_phydev_platform_data bfin_phydev_data[] = { | |
| { | |
| .addr = 1, | |
| .irq = IRQ_MAC_PHYINT, | |
| }, | |
| }; | |
| static struct bfin_mii_bus_platform_data bfin_mii_bus_data = { | |
| .phydev_number = 1, | |
| .phydev_data = bfin_phydev_data, | |
| .phy_mode = PHY_INTERFACE_MODE_MII, | |
| .mac_peripherals = bfin_mac_peripherals, | |
| }; | |
| static struct platform_device bfin_mii_bus = { | |
| .name = "bfin_mii_bus", | |
| .dev = { | |
| .platform_data = &bfin_mii_bus_data, | |
| } | |
| }; | |
| static struct platform_device bfin_mac_device = { | |
| .name = "bfin_mac", | |
| .dev = { | |
| .platform_data = &bfin_mii_bus, | |
| } | |
| }; | |
| #endif | |
| #if IS_ENABLED(CONFIG_PATA_PLATFORM) | |
| #define PATA_INT IRQ_PF14 | |
| static struct pata_platform_info bfin_pata_platform_data = { | |
| .ioport_shift = 2, | |
| .irq_type = IRQF_TRIGGER_HIGH, | |
| }; | |
| static struct resource bfin_pata_resources[] = { | |
| { | |
| .start = 0x2030C000, | |
| .end = 0x2030C01F, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = 0x2030D018, | |
| .end = 0x2030D01B, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| { | |
| .start = PATA_INT, | |
| .end = PATA_INT, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static struct platform_device bfin_pata_device = { | |
| .name = "pata_platform", | |
| .id = -1, | |
| .num_resources = ARRAY_SIZE(bfin_pata_resources), | |
| .resource = bfin_pata_resources, | |
| .dev = { | |
| .platform_data = &bfin_pata_platform_data, | |
| } | |
| }; | |
| #endif | |
| static const unsigned int cclk_vlev_datasheet[] = | |
| { | |
| VRPAIR(VLEV_085, 250000000), | |
| VRPAIR(VLEV_090, 376000000), | |
| VRPAIR(VLEV_095, 426000000), | |
| VRPAIR(VLEV_100, 426000000), | |
| VRPAIR(VLEV_105, 476000000), | |
| VRPAIR(VLEV_110, 476000000), | |
| VRPAIR(VLEV_115, 476000000), | |
| VRPAIR(VLEV_120, 500000000), | |
| VRPAIR(VLEV_125, 533000000), | |
| VRPAIR(VLEV_130, 600000000), | |
| }; | |
| static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { | |
| .tuple_tab = cclk_vlev_datasheet, | |
| .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), | |
| .vr_settling_time = 25 /* us */, | |
| }; | |
| static struct platform_device bfin_dpmc = { | |
| .name = "bfin dpmc", | |
| .dev = { | |
| .platform_data = &bfin_dmpc_vreg_data, | |
| }, | |
| }; | |
| static struct platform_device *cm_bf537u_devices[] __initdata = { | |
| &bfin_dpmc, | |
| #if IS_ENABLED(CONFIG_FB_HITACHI_TX09) | |
| &hitachi_fb_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_RTC_DRV_BFIN) | |
| &rtc_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_SERIAL_BFIN) | |
| #ifdef CONFIG_SERIAL_BFIN_UART0 | |
| &bfin_uart0_device, | |
| #endif | |
| #ifdef CONFIG_SERIAL_BFIN_UART1 | |
| &bfin_uart1_device, | |
| #endif | |
| #endif | |
| #if IS_ENABLED(CONFIG_BFIN_SIR) | |
| #ifdef CONFIG_BFIN_SIR0 | |
| &bfin_sir0_device, | |
| #endif | |
| #ifdef CONFIG_BFIN_SIR1 | |
| &bfin_sir1_device, | |
| #endif | |
| #endif | |
| #if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI) | |
| &i2c_bfin_twi_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) | |
| #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART | |
| &bfin_sport0_uart_device, | |
| #endif | |
| #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART | |
| &bfin_sport1_uart_device, | |
| #endif | |
| #endif | |
| #if IS_ENABLED(CONFIG_USB_ISP1362_HCD) | |
| &isp1362_hcd_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_SMC91X) | |
| &smc91x_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_BFIN_MAC) | |
| &bfin_mii_bus, | |
| &bfin_mac_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_USB_NET2272) | |
| &net2272_bfin_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_SPI_BFIN5XX) | |
| &bfin_spi0_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_PATA_PLATFORM) | |
| &bfin_pata_device, | |
| #endif | |
| #if IS_ENABLED(CONFIG_MTD_GPIO_ADDR) | |
| &cm_flash_device, | |
| #endif | |
| }; | |
| static int __init net2272_init(void) | |
| { | |
| #if IS_ENABLED(CONFIG_USB_NET2272) | |
| int ret; | |
| ret = gpio_request(GPIO_PH15, driver_name); | |
| if (ret) | |
| return ret; | |
| ret = gpio_request(GPIO_PH13, "net2272"); | |
| if (ret) { | |
| gpio_free(GPIO_PH15); | |
| return ret; | |
| } | |
| /* Set PH15 Low make /AMS2 work properly */ | |
| gpio_direction_output(GPIO_PH15, 0); | |
| /* enable CLKBUF output */ | |
| bfin_write_VR_CTL(bfin_read_VR_CTL() | CLKBUFOE); | |
| /* Reset the USB chip */ | |
| gpio_direction_output(GPIO_PH13, 0); | |
| mdelay(2); | |
| gpio_set_value(GPIO_PH13, 1); | |
| #endif | |
| return 0; | |
| } | |
| static int __init cm_bf537u_init(void) | |
| { | |
| printk(KERN_INFO "%s(): registering device resources\n", __func__); | |
| platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices)); | |
| #if IS_ENABLED(CONFIG_SPI_BFIN5XX) | |
| spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); | |
| #endif | |
| #if IS_ENABLED(CONFIG_PATA_PLATFORM) | |
| irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN); | |
| #endif | |
| if (net2272_init()) | |
| pr_warning("unable to configure net2272; it probably won't work\n"); | |
| return 0; | |
| } | |
| arch_initcall(cm_bf537u_init); | |
| static struct platform_device *cm_bf537u_early_devices[] __initdata = { | |
| #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) | |
| #ifdef CONFIG_SERIAL_BFIN_UART0 | |
| &bfin_uart0_device, | |
| #endif | |
| #ifdef CONFIG_SERIAL_BFIN_UART1 | |
| &bfin_uart1_device, | |
| #endif | |
| #endif | |
| #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE) | |
| #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART | |
| &bfin_sport0_uart_device, | |
| #endif | |
| #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART | |
| &bfin_sport1_uart_device, | |
| #endif | |
| #endif | |
| }; | |
| void __init native_machine_early_platform_add_devices(void) | |
| { | |
| printk(KERN_INFO "register early platform devices\n"); | |
| early_platform_add_devices(cm_bf537u_early_devices, | |
| ARRAY_SIZE(cm_bf537u_early_devices)); | |
| } | |
| int bfin_get_ether_addr(char *addr) | |
| { | |
| return 1; | |
| } | |
| EXPORT_SYMBOL(bfin_get_ether_addr); |