blob: 7560ff9bcb387aac00f4c7433972fa0fd9548470 [file] [log] [blame]
#
# Block device driver configuration
#
mainmenu_option next_comment
comment 'Block devices'
tristate 'Normal floppy disk support' CONFIG_BLK_DEV_FD
if [ "$CONFIG_AMIGA" = "y" ]; then
tristate 'Amiga floppy support' CONFIG_AMIGA_FLOPPY
fi
if [ "$CONFIG_ATARI" = "y" ]; then
tristate 'Atari floppy support' CONFIG_ATARI_FLOPPY
fi
if [ "$CONFIG_MAC" = "y" ]; then
dep_bool 'Macintosh IIfx/Quadra 900/Quadra 950 floppy support (EXPERIMENTAL)' CONFIG_BLK_DEV_SWIM_IOP $CONFIG_EXPERIMENTAL
fi
if [ "$CONFIG_MCA" = "y" ]; then
tristate 'PS/2 ESDI hard disk support' CONFIG_BLK_DEV_PS2
fi
if [ "$CONFIG_ZORRO" = "y" ]; then
tristate 'Amiga Zorro II ramdisk support' CONFIG_AMIGA_Z2RAM
fi
if [ "$CONFIG_ATARI" = "y" ]; then
tristate 'Atari ACSI support' CONFIG_ATARI_ACSI
if [ "$CONFIG_ATARI_ACSI" != "n" ]; then
comment 'Some devices (e.g. CD jukebox) support multiple LUNs'
bool ' Probe all LUNs on each ACSI device' CONFIG_ACSI_MULTI_LUN
tristate ' Atari SLM laser printer support' CONFIG_ATARI_SLM
fi
fi
dep_tristate 'XT hard disk support' CONFIG_BLK_DEV_XD $CONFIG_ISA
dep_tristate 'Parallel port IDE device support' CONFIG_PARIDE $CONFIG_PARPORT
if [ "$CONFIG_PARIDE" = "y" -o "$CONFIG_PARIDE" = "m" ]; then
source drivers/block/paride/Config.in
fi
dep_tristate 'Compaq SMART2 support' CONFIG_BLK_CPQ_DA $CONFIG_PCI
dep_tristate 'Compaq Smart Array 5xxx support' CONFIG_BLK_CPQ_CISS_DA $CONFIG_PCI
dep_mbool ' SCSI tape drive support for Smart Array 5xxx' CONFIG_CISS_SCSI_TAPE $CONFIG_BLK_CPQ_CISS_DA $CONFIG_SCSI
dep_mbool ' Enable monitor thread' CONFIG_CISS_MONITOR_THREAD $CONFIG_BLK_CPQ_CISS_DA
dep_tristate 'Mylex DAC960/DAC1100 PCI RAID Controller support' CONFIG_BLK_DEV_DAC960 $CONFIG_PCI
dep_tristate 'Micro Memory MM5415 Battery Backed RAM support (EXPERIMENTAL)' CONFIG_BLK_DEV_UMEM $CONFIG_PCI $CONFIG_EXPERIMENTAL
dep_tristate 'Promise SATA SX8 support' CONFIG_BLK_DEV_SX8 $CONFIG_PCI
tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
dep_tristate 'Network block device support' CONFIG_BLK_DEV_NBD $CONFIG_NET
tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" -o "$CONFIG_BLK_DEV_RAM" = "m" ]; then
int ' Default RAM disk size' CONFIG_BLK_DEV_RAM_SIZE 4096
fi
dep_bool ' Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD $CONFIG_BLK_DEV_RAM
bool 'Per partition statistics in /proc/partitions' CONFIG_BLK_STATS
endmenu