src/main.conf - pub/scm/network/connman/connman - Git at Google

 [General]

 # Set input request timeout. Default is 120 seconds
 # The request for inputs like passphrase will timeout
 # after certain amount of time. Use this setting to
 # increase the value in case of different user
 # interface designs.
 # InputRequestTimeout = 120

 # Set browser launch timeout. Default is 300 seconds
 # The request for launching a browser for portal pages
 # will timeout after certain amount of time. Use this
 # setting to increase the value in case of different
 # user interface designs.
 # BrowserLaunchTimeout = 300

 # If wifi is disconnected, the background scanning will follow a simple
 # backoff mechanism from 3s up to 5 minutes. Then, it will stay in 5
 # minutes unless user specifically asks for scanning through a D-Bus
 # call. If so, the mechanism will start again from 3s. This feature
 # activates also the background scanning while being connected, which
 # is required for roaming on wifi.
 # When BackgroundScanning is false, ConnMan will not perform any scan
 # regardless of wifi is connected or not, unless it is requested by
 # the user through a D-Bus call.
 # BackgroundScanning = true

 # Assume that service gateways also function as timeservers.
 # UseGatewaysAsTimeservers = false

 # List of Fallback timeservers separated by ",".
 # These timeservers are used for NTP sync when there are
 # no timeservers set by the user or by the service, and
 # when UseGatewaysAsTimeservers = false. These can contain
 # mixed combination of fully qualified domain names, IPv4
 # and IPv6 addresses.
 # FallbackTimeservers =

 # List of fallback nameservers separated by "," used if no
 # nameservers are otherwise provided by the service. The
 # nameserver entries must be in numeric format, host
 # names are ignored.
 # FallbackNameservers =

 # List of technologies that are marked autoconnectable
 # by default, separated by commas ",". The default value
 # for this entry when empty is ethernet,wifi,cellular.
 # Services that are automatically connected must have been
 # set up and saved to storage beforehand.
 # DefaultAutoConnectTechnologies =

 # List of preferred technologies from the most preferred
 # one to the least preferred one separated by commas ",".
 # Services of the listed technology type will be tried one
 # by one in the order given, until one of them gets connected
 # or they are all tried. A service of a preferred technology
 # type in state 'ready' will get the default route when
 # compared to another preferred type further down the list
 # with state 'ready' or with a non-preferred type; a service
 # of a preferred technology type in state 'online' will get
 # the default route when compared to either a non-preferred
 # type or a preferred type further down in the list.
 # PreferredTechnologies =

 # List of blacklisted network interfaces separated by ",".
 # Found interfaces will be compared to the list and will
 # not be handled by ConnMan, if their first characters
 # match any of the list entries. Default value is
 # vmnet,vboxnet,virbr,ifb,ve-,vb-.
 # NetworkInterfaceBlacklist = vmnet,vboxnet,virbr,ifb,ve-,vb-

 # Allow ConnMan to change the system hostname. This can
 # happen for example if we receive DHCP hostname option.
 # Default value is true.
 # AllowHostnameUpdates = true

 # Allow ConnMan to change the system domainname. This can
 # happen for example if we receive DHCP domainname option.
 # Default value is true.
 # AllowDomainnameUpdates = true

 # Keep only a single connected technology at any time. When a new
 # service is connected by the user or a better one is found according
 # to PreferredTechnologies, the new service is kept connected and all
 # the other previously connected services are disconnected. With this
 # setting it does not matter whether the previously connected services
 # are in 'online' or 'ready' states, the newly connected service is
 # the only one that will be kept connected. A service connected by the
 # user will be used until going out of network coverage. With this
 # setting enabled applications will notice more network breaks than
 # normal. Default value is false.
 # SingleConnectedTechnology = false

 # List of technologies for which tethering is allowed separated by ",".
 # The default value is wifi,bluetooth,gadget. Only those technologies
 # listed here are used for tethering. If ethernet tethering is desired,
 # then ethernet should be added to the list. The technologies listed here
 # have to support tethering, currently tethering is implemented for wifi,
 # bluetooth, gadget and ethernet.
 # NOTE that if ethernet tethering is enabled, then a DHCP server is
 # started on all ethernet interfaces. Tethered ethernet should
 # never be connected to corporate or home network as it will disrupt
 # normal operation of these networks. Due to this ethernet is not
 # tethered by default. Do not activate ethernet tethering unless you
 # really know what you are doing.
 # TetheringTechnologies = wifi,bluetooth,gadget

 # Restore earlier tethering status when returning from offline mode,
 # re-enabling a technology, and after restarts and reboots.
 # Default value is false.
 # PersistentTetheringMode = false

 # Automatically enable Anycast 6to4 if possible. This is not recommended, as
 # the use of 6to4 will generally lead to a severe degradation of connection
 # quality. See RFC6343. Default value is false (as recommended by RFC6343
 # section 4.1).
 # Enable6to4 = false

 # Enable use of http get as on online status check.
 # When a service is in a READY state, and is selected as default,
 # ConnMan will issue an HTTP GET request to verify that end-to-end
 # connectivity is successful. Only then the service will be
 # transitioned to ONLINE state.
 # If this setting is false, the default service will remain in READY state.
 # Default value is true.
 # EnableOnlineCheck = false

 # Range of intervals between two online check requests.
 # When an online check request fails, another one is triggered after a
 # longer interval. The intervals follow the power of two series of numbers
 # between OnlineCheckInitialInterval and OnlineCheckMaxInterval.
 # Default range is [1, 12], corresponding to the following intervals, in
 # seconds: 1, 4, 9, 16, 25, 36, 49, 64, 81, 100, 121 and 144.
 # OnlineCheckInitialInterval = 1
 # OnlineCheckMaxInterval = 12

 # WARNING: Experimental feature!!!
 # In addition to EnableOnlineCheck setting, enable or disable use of HTTP GET
 # to detect the loss of end-to-end connectivity.
 # If this setting is false, when the default service transitions to ONLINE
 # state, the HTTP GET request is no more called until next cycle, initiated
 # by a transition of the default service to DISCONNECT state.
 # If this setting is true, the HTTP GET request keeps beeing called to guarantee
 # that end-to-end connectivity is still successful. If not, the default service
 # will transition to READY state, enabling another service to become the
 # default one, in replacement.
 # EnableOnlineToReadyTransition = false

 # List of technologies with AutoConnect = true which are always connected
 # regardless of PreferredTechnologies setting. Default value is empty and
 # will connect a technology only if it is at a higher preference than any
 # other which is already connected.
 # This setting has no effect if SingleConnectedTechnologies is enabled.
 # AlwaysConnectedTechnologies =

 # Enable auto connection of services in roaming.
 # If this setting is false, roaming services are not auto-connected by ConnMan.
 # Default value is false.
 # AutoConnectRoamingServices = false

 # Enable address conflict detection
 # If this setting is true, ConnMan will send probe ARP packets to see
 # if an IPv4 address is already in use before assigning the address
 # to an interface (in accordance with RFC 5227).
 # Default value is false.
 # AddressConflictDetection = false
	[General]

	# Set input request timeout. Default is 120 seconds
	# The request for inputs like passphrase will timeout
	# after certain amount of time. Use this setting to
	# increase the value in case of different user
	# interface designs.
	# InputRequestTimeout = 120

	# Set browser launch timeout. Default is 300 seconds
	# The request for launching a browser for portal pages
	# will timeout after certain amount of time. Use this
	# setting to increase the value in case of different
	# user interface designs.
	# BrowserLaunchTimeout = 300

	# If wifi is disconnected, the background scanning will follow a simple
	# backoff mechanism from 3s up to 5 minutes. Then, it will stay in 5
	# minutes unless user specifically asks for scanning through a D-Bus
	# call. If so, the mechanism will start again from 3s. This feature
	# activates also the background scanning while being connected, which
	# is required for roaming on wifi.
	# When BackgroundScanning is false, ConnMan will not perform any scan
	# regardless of wifi is connected or not, unless it is requested by
	# the user through a D-Bus call.
	# BackgroundScanning = true

	# Assume that service gateways also function as timeservers.
	# UseGatewaysAsTimeservers = false

	# List of Fallback timeservers separated by ",".
	# These timeservers are used for NTP sync when there are
	# no timeservers set by the user or by the service, and
	# when UseGatewaysAsTimeservers = false. These can contain
	# mixed combination of fully qualified domain names, IPv4
	# and IPv6 addresses.
	# FallbackTimeservers =

	# List of fallback nameservers separated by "," used if no
	# nameservers are otherwise provided by the service. The
	# nameserver entries must be in numeric format, host
	# names are ignored.
	# FallbackNameservers =

	# List of technologies that are marked autoconnectable
	# by default, separated by commas ",". The default value
	# for this entry when empty is ethernet,wifi,cellular.
	# Services that are automatically connected must have been
	# set up and saved to storage beforehand.
	# DefaultAutoConnectTechnologies =

	# List of preferred technologies from the most preferred
	# one to the least preferred one separated by commas ",".
	# Services of the listed technology type will be tried one
	# by one in the order given, until one of them gets connected
	# or they are all tried. A service of a preferred technology
	# type in state 'ready' will get the default route when
	# compared to another preferred type further down the list
	# with state 'ready' or with a non-preferred type; a service
	# of a preferred technology type in state 'online' will get
	# the default route when compared to either a non-preferred
	# type or a preferred type further down in the list.
	# PreferredTechnologies =

	# List of blacklisted network interfaces separated by ",".
	# Found interfaces will be compared to the list and will
	# not be handled by ConnMan, if their first characters
	# match any of the list entries. Default value is
	# vmnet,vboxnet,virbr,ifb,ve-,vb-.
	# NetworkInterfaceBlacklist = vmnet,vboxnet,virbr,ifb,ve-,vb-

	# Allow ConnMan to change the system hostname. This can
	# happen for example if we receive DHCP hostname option.
	# Default value is true.
	# AllowHostnameUpdates = true

	# Allow ConnMan to change the system domainname. This can
	# happen for example if we receive DHCP domainname option.
	# Default value is true.
	# AllowDomainnameUpdates = true

	# Keep only a single connected technology at any time. When a new
	# service is connected by the user or a better one is found according
	# to PreferredTechnologies, the new service is kept connected and all
	# the other previously connected services are disconnected. With this
	# setting it does not matter whether the previously connected services
	# are in 'online' or 'ready' states, the newly connected service is
	# the only one that will be kept connected. A service connected by the
	# user will be used until going out of network coverage. With this
	# setting enabled applications will notice more network breaks than
	# normal. Default value is false.
	# SingleConnectedTechnology = false

	# List of technologies for which tethering is allowed separated by ",".
	# The default value is wifi,bluetooth,gadget. Only those technologies
	# listed here are used for tethering. If ethernet tethering is desired,
	# then ethernet should be added to the list. The technologies listed here
	# have to support tethering, currently tethering is implemented for wifi,
	# bluetooth, gadget and ethernet.
	# NOTE that if ethernet tethering is enabled, then a DHCP server is
	# started on all ethernet interfaces. Tethered ethernet should
	# never be connected to corporate or home network as it will disrupt
	# normal operation of these networks. Due to this ethernet is not
	# tethered by default. Do not activate ethernet tethering unless you
	# really know what you are doing.
	# TetheringTechnologies = wifi,bluetooth,gadget

	# Restore earlier tethering status when returning from offline mode,
	# re-enabling a technology, and after restarts and reboots.
	# Default value is false.
	# PersistentTetheringMode = false

	# Automatically enable Anycast 6to4 if possible. This is not recommended, as
	# the use of 6to4 will generally lead to a severe degradation of connection
	# quality. See RFC6343. Default value is false (as recommended by RFC6343
	# section 4.1).
	# Enable6to4 = false

	# Enable use of http get as on online status check.
	# When a service is in a READY state, and is selected as default,
	# ConnMan will issue an HTTP GET request to verify that end-to-end
	# connectivity is successful. Only then the service will be
	# transitioned to ONLINE state.
	# If this setting is false, the default service will remain in READY state.
	# Default value is true.
	# EnableOnlineCheck = false

	# Range of intervals between two online check requests.
	# When an online check request fails, another one is triggered after a
	# longer interval. The intervals follow the power of two series of numbers
	# between OnlineCheckInitialInterval and OnlineCheckMaxInterval.
	# Default range is [1, 12], corresponding to the following intervals, in
	# seconds: 1, 4, 9, 16, 25, 36, 49, 64, 81, 100, 121 and 144.
	# OnlineCheckInitialInterval = 1
	# OnlineCheckMaxInterval = 12

	# WARNING: Experimental feature!!!
	# In addition to EnableOnlineCheck setting, enable or disable use of HTTP GET
	# to detect the loss of end-to-end connectivity.
	# If this setting is false, when the default service transitions to ONLINE
	# state, the HTTP GET request is no more called until next cycle, initiated
	# by a transition of the default service to DISCONNECT state.
	# If this setting is true, the HTTP GET request keeps beeing called to guarantee
	# that end-to-end connectivity is still successful. If not, the default service
	# will transition to READY state, enabling another service to become the
	# default one, in replacement.
	# EnableOnlineToReadyTransition = false

	# List of technologies with AutoConnect = true which are always connected
	# regardless of PreferredTechnologies setting. Default value is empty and
	# will connect a technology only if it is at a higher preference than any
	# other which is already connected.
	# This setting has no effect if SingleConnectedTechnologies is enabled.
	# AlwaysConnectedTechnologies =

	# Enable auto connection of services in roaming.
	# If this setting is false, roaming services are not auto-connected by ConnMan.
	# Default value is false.
	# AutoConnectRoamingServices = false

	# Enable address conflict detection
	# If this setting is true, ConnMan will send probe ARP packets to see
	# if an IPv4 address is already in use before assigning the address
	# to an interface (in accordance with RFC 5227).
	# Default value is false.
	# AddressConflictDetection = false