Merge tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: omap: fix broken PIO mode
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
mmc: dw_mmc: fix error handling in PIO mode
mmc: dw_mmc: correct mishandling error interrupt
mmc: dw_mmc: amend using error interrupt status
mmc: atmel-mci: not busy flag has also to be used for read operations
mmc: sdhci-esdhc: break out early if clock is 0
mmc: mxs-mmc: fix deadlock caused by recursion loop
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
mmc: bfin_sdh: fix dma_desc_array build error
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index f1c84de..172a768 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1411,7 +1411,8 @@
/* complete ongoing async transfer before issuing discard */
if (card->host->areq)
mmc_blk_issue_rw_rq(mq, NULL);
- if (req->cmd_flags & REQ_SECURE)
+ if (req->cmd_flags & REQ_SECURE &&
+ !(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN))
ret = mmc_blk_issue_secdiscard_rq(mq, req);
else
ret = mmc_blk_issue_discard_rq(mq, req);
@@ -1716,6 +1717,7 @@
#define CID_MANFID_SANDISK 0x2
#define CID_MANFID_TOSHIBA 0x11
#define CID_MANFID_MICRON 0x13
+#define CID_MANFID_SAMSUNG 0x15
static const struct mmc_fixup blk_fixups[] =
{
@@ -1752,6 +1754,28 @@
MMC_FIXUP(CID_NAME_ANY, CID_MANFID_MICRON, 0x200, add_quirk_mmc,
MMC_QUIRK_LONG_READ_TIME),
+ /*
+ * On these Samsung MoviNAND parts, performing secure erase or
+ * secure trim can result in unrecoverable corruption due to a
+ * firmware bug.
+ */
+ MMC_FIXUP("M8G2FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("MAG4FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("MBG8FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("MCGAFA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("VAL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("VYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("KYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+ MMC_FIXUP("VZL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+ MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+
END_FIXUP
};
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 322412c..a53c7c4 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -81,6 +81,7 @@
bool has_bad_data_ordering;
bool need_reset_after_xfer;
bool need_blksz_mul_4;
+ bool need_notbusy_for_read_ops;
};
struct atmel_mci_dma {
@@ -1625,7 +1626,8 @@
__func__);
atmci_set_completed(host, EVENT_XFER_COMPLETE);
- if (host->data->flags & MMC_DATA_WRITE) {
+ if (host->caps.need_notbusy_for_read_ops ||
+ (host->data->flags & MMC_DATA_WRITE)) {
atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
state = STATE_WAITING_NOTBUSY;
} else if (host->mrq->stop) {
@@ -2218,6 +2220,7 @@
host->caps.has_bad_data_ordering = 1;
host->caps.need_reset_after_xfer = 1;
host->caps.need_blksz_mul_4 = 1;
+ host->caps.need_notbusy_for_read_ops = 0;
/* keep only major version number */
switch (version & 0xf00) {
@@ -2238,6 +2241,7 @@
case 0x200:
host->caps.has_rwproof = 1;
host->caps.need_blksz_mul_4 = 0;
+ host->caps.need_notbusy_for_read_ops = 1;
case 0x100:
host->caps.has_bad_data_ordering = 0;
host->caps.need_reset_after_xfer = 0;
diff --git a/drivers/mmc/host/bfin_sdh.c b/drivers/mmc/host/bfin_sdh.c
index 0366617..a17dd73 100644
--- a/drivers/mmc/host/bfin_sdh.c
+++ b/drivers/mmc/host/bfin_sdh.c
@@ -49,13 +49,6 @@
#define bfin_write_SDH_CFG bfin_write_RSI_CFG
#endif
-struct dma_desc_array {
- unsigned long start_addr;
- unsigned short cfg;
- unsigned short x_count;
- short x_modify;
-} __packed;
-
struct sdh_host {
struct mmc_host *mmc;
spinlock_t lock;
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 72dc3cd..af40d22 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -627,6 +627,7 @@
{
struct dw_mci *host = slot->host;
u32 div;
+ u32 clk_en_a;
if (slot->clock != host->current_speed) {
div = host->bus_hz / slot->clock;
@@ -659,9 +660,11 @@
mci_send_cmd(slot,
SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
- /* enable clock */
- mci_writel(host, CLKENA, ((SDMMC_CLKEN_ENABLE |
- SDMMC_CLKEN_LOW_PWR) << slot->id));
+ /* enable clock; only low power if no SDIO */
+ clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
+ if (!(mci_readl(host, INTMASK) & SDMMC_INT_SDIO(slot->id)))
+ clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
+ mci_writel(host, CLKENA, clk_en_a);
/* inform CIU */
mci_send_cmd(slot,
@@ -862,6 +865,30 @@
return present;
}
+/*
+ * Disable lower power mode.
+ *
+ * Low power mode will stop the card clock when idle. According to the
+ * description of the CLKENA register we should disable low power mode
+ * for SDIO cards if we need SDIO interrupts to work.
+ *
+ * This function is fast if low power mode is already disabled.
+ */
+static void dw_mci_disable_low_power(struct dw_mci_slot *slot)
+{
+ struct dw_mci *host = slot->host;
+ u32 clk_en_a;
+ const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
+
+ clk_en_a = mci_readl(host, CLKENA);
+
+ if (clk_en_a & clken_low_pwr) {
+ mci_writel(host, CLKENA, clk_en_a & ~clken_low_pwr);
+ mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
+ SDMMC_CMD_PRV_DAT_WAIT, 0);
+ }
+}
+
static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
{
struct dw_mci_slot *slot = mmc_priv(mmc);
@@ -871,6 +898,14 @@
/* Enable/disable Slot Specific SDIO interrupt */
int_mask = mci_readl(host, INTMASK);
if (enb) {
+ /*
+ * Turn off low power mode if it was enabled. This is a bit of
+ * a heavy operation and we disable / enable IRQs a lot, so
+ * we'll leave low power mode disabled and it will get
+ * re-enabled again in dw_mci_setup_bus().
+ */
+ dw_mci_disable_low_power(slot);
+
mci_writel(host, INTMASK,
(int_mask | SDMMC_INT_SDIO(slot->id)));
} else {
@@ -1429,22 +1464,10 @@
nbytes += len;
remain -= len;
} while (remain);
- sg_miter->consumed = offset;
+ sg_miter->consumed = offset;
status = mci_readl(host, MINTSTS);
mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
- if (status & DW_MCI_DATA_ERROR_FLAGS) {
- host->data_status = status;
- data->bytes_xfered += nbytes;
- sg_miter_stop(sg_miter);
- host->sg = NULL;
- smp_wmb();
-
- set_bit(EVENT_DATA_ERROR, &host->pending_events);
-
- tasklet_schedule(&host->tasklet);
- return;
- }
} while (status & SDMMC_INT_RXDR); /*if the RXDR is ready read again*/
data->bytes_xfered += nbytes;
@@ -1497,23 +1520,10 @@
nbytes += len;
remain -= len;
} while (remain);
- sg_miter->consumed = offset;
+ sg_miter->consumed = offset;
status = mci_readl(host, MINTSTS);
mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
- if (status & DW_MCI_DATA_ERROR_FLAGS) {
- host->data_status = status;
- data->bytes_xfered += nbytes;
- sg_miter_stop(sg_miter);
- host->sg = NULL;
-
- smp_wmb();
-
- set_bit(EVENT_DATA_ERROR, &host->pending_events);
-
- tasklet_schedule(&host->tasklet);
- return;
- }
} while (status & SDMMC_INT_TXDR); /* if TXDR write again */
data->bytes_xfered += nbytes;
@@ -1547,12 +1557,11 @@
static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
{
struct dw_mci *host = dev_id;
- u32 status, pending;
+ u32 pending;
unsigned int pass_count = 0;
int i;
do {
- status = mci_readl(host, RINTSTS);
pending = mci_readl(host, MINTSTS); /* read-only mask reg */
/*
@@ -1570,7 +1579,7 @@
if (pending & DW_MCI_CMD_ERROR_FLAGS) {
mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
- host->cmd_status = status;
+ host->cmd_status = pending;
smp_wmb();
set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
}
@@ -1578,18 +1587,16 @@
if (pending & DW_MCI_DATA_ERROR_FLAGS) {
/* if there is an error report DATA_ERROR */
mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
- host->data_status = status;
+ host->data_status = pending;
smp_wmb();
set_bit(EVENT_DATA_ERROR, &host->pending_events);
- if (!(pending & (SDMMC_INT_DTO | SDMMC_INT_DCRC |
- SDMMC_INT_SBE | SDMMC_INT_EBE)))
- tasklet_schedule(&host->tasklet);
+ tasklet_schedule(&host->tasklet);
}
if (pending & SDMMC_INT_DATA_OVER) {
mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
if (!host->data_status)
- host->data_status = status;
+ host->data_status = pending;
smp_wmb();
if (host->dir_status == DW_MCI_RECV_STATUS) {
if (host->sg != NULL)
@@ -1613,7 +1620,7 @@
if (pending & SDMMC_INT_CMD_DONE) {
mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
- dw_mci_cmd_interrupt(host, status);
+ dw_mci_cmd_interrupt(host, pending);
}
if (pending & SDMMC_INT_CD) {
diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
index a51f930..ad3fcea 100644
--- a/drivers/mmc/host/mxs-mmc.c
+++ b/drivers/mmc/host/mxs-mmc.c
@@ -285,11 +285,11 @@
writel(stat & MXS_MMC_IRQ_BITS,
host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
+ spin_unlock(&host->lock);
+
if ((stat & BM_SSP_CTRL1_SDIO_IRQ) && (stat & BM_SSP_CTRL1_SDIO_IRQ_EN))
mmc_signal_sdio_irq(host->mmc);
- spin_unlock(&host->lock);
-
if (stat & BM_SSP_CTRL1_RESP_TIMEOUT_IRQ)
cmd->error = -ETIMEDOUT;
else if (stat & BM_SSP_CTRL1_RESP_ERR_IRQ)
@@ -644,11 +644,6 @@
host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET);
writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_SET);
-
- if (readl(host->base + HW_SSP_STATUS(host)) &
- BM_SSP_STATUS_SDIO_IRQ)
- mmc_signal_sdio_irq(host->mmc);
-
} else {
writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR);
@@ -657,6 +652,11 @@
}
spin_unlock_irqrestore(&host->lock, flags);
+
+ if (enable && readl(host->base + HW_SSP_STATUS(host)) &
+ BM_SSP_STATUS_SDIO_IRQ)
+ mmc_signal_sdio_irq(host->mmc);
+
}
static const struct mmc_host_ops mxs_mmc_ops = {
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index 50e08f0..a5999a7 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -668,7 +668,7 @@
static void
mmc_omap_xfer_data(struct mmc_omap_host *host, int write)
{
- int n;
+ int n, nwords;
if (host->buffer_bytes_left == 0) {
host->sg_idx++;
@@ -678,15 +678,23 @@
n = 64;
if (n > host->buffer_bytes_left)
n = host->buffer_bytes_left;
+
+ nwords = n / 2;
+ nwords += n & 1; /* handle odd number of bytes to transfer */
+
host->buffer_bytes_left -= n;
host->total_bytes_left -= n;
host->data->bytes_xfered += n;
if (write) {
- __raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n);
+ __raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA),
+ host->buffer, nwords);
} else {
- __raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n);
+ __raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA),
+ host->buffer, nwords);
}
+
+ host->buffer += nwords;
}
static inline void mmc_omap_report_irq(u16 status)
diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h
index b97b2f5..d25f9ab 100644
--- a/drivers/mmc/host/sdhci-esdhc.h
+++ b/drivers/mmc/host/sdhci-esdhc.h
@@ -48,14 +48,14 @@
int div = 1;
u32 temp;
+ if (clock == 0)
+ goto out;
+
temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
| ESDHC_CLOCK_MASK);
sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
- if (clock == 0)
- goto out;
-
while (host->max_clk / pre_div / 16 > clock && pre_div < 256)
pre_div *= 2;
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 111aca5..4b27f9f 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -239,6 +239,7 @@
#define MMC_QUIRK_BLK_NO_CMD23 (1<<7) /* Avoid CMD23 for regular multiblock */
#define MMC_QUIRK_BROKEN_BYTE_MODE_512 (1<<8) /* Avoid sending 512 bytes in */
#define MMC_QUIRK_LONG_READ_TIME (1<<9) /* Data read time > CSD says */
+#define MMC_QUIRK_SEC_ERASE_TRIM_BROKEN (1<<10) /* Skip secure for erase/trim */
/* byte mode */
unsigned int poweroff_notify_state; /* eMMC4.5 notify feature */
#define MMC_NO_POWER_NOTIFICATION 0
