|  | // SPDX-License-Identifier: GPL-2.0-only | 
|  | /* | 
|  | * adv7842 - Analog Devices ADV7842 video decoder driver | 
|  | * | 
|  | * Copyright 2013 Cisco Systems, Inc. and/or its affiliates. All rights reserved. | 
|  | */ | 
|  |  | 
|  | /* | 
|  | * References (c = chapter, p = page): | 
|  | * REF_01 - Analog devices, ADV7842, | 
|  | *		Register Settings Recommendations, Rev. 1.9, April 2011 | 
|  | * REF_02 - Analog devices, Software User Guide, UG-206, | 
|  | *		ADV7842 I2C Register Maps, Rev. 0, November 2010 | 
|  | * REF_03 - Analog devices, Hardware User Guide, UG-214, | 
|  | *		ADV7842 Fast Switching 2:1 HDMI 1.4 Receiver with 3D-Comb | 
|  | *		Decoder and Digitizer , Rev. 0, January 2011 | 
|  | */ | 
|  |  | 
|  |  | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/videodev2.h> | 
|  | #include <linux/workqueue.h> | 
|  | #include <linux/v4l2-dv-timings.h> | 
|  | #include <linux/hdmi.h> | 
|  | #include <media/cec.h> | 
|  | #include <media/v4l2-device.h> | 
|  | #include <media/v4l2-event.h> | 
|  | #include <media/v4l2-ctrls.h> | 
|  | #include <media/v4l2-dv-timings.h> | 
|  | #include <media/i2c/adv7842.h> | 
|  |  | 
|  | static int debug; | 
|  | module_param(debug, int, 0644); | 
|  | MODULE_PARM_DESC(debug, "debug level (0-2)"); | 
|  |  | 
|  | MODULE_DESCRIPTION("Analog Devices ADV7842 video decoder driver"); | 
|  | MODULE_AUTHOR("Hans Verkuil <hansverk@cisco.com>"); | 
|  | MODULE_AUTHOR("Martin Bugge <marbugge@cisco.com>"); | 
|  | MODULE_LICENSE("GPL"); | 
|  |  | 
|  | /* ADV7842 system clock frequency */ | 
|  | #define ADV7842_fsc (28636360) | 
|  |  | 
|  | #define ADV7842_RGB_OUT					(1 << 1) | 
|  |  | 
|  | #define ADV7842_OP_FORMAT_SEL_8BIT			(0 << 0) | 
|  | #define ADV7842_OP_FORMAT_SEL_10BIT			(1 << 0) | 
|  | #define ADV7842_OP_FORMAT_SEL_12BIT			(2 << 0) | 
|  |  | 
|  | #define ADV7842_OP_MODE_SEL_SDR_422			(0 << 5) | 
|  | #define ADV7842_OP_MODE_SEL_DDR_422			(1 << 5) | 
|  | #define ADV7842_OP_MODE_SEL_SDR_444			(2 << 5) | 
|  | #define ADV7842_OP_MODE_SEL_DDR_444			(3 << 5) | 
|  | #define ADV7842_OP_MODE_SEL_SDR_422_2X			(4 << 5) | 
|  | #define ADV7842_OP_MODE_SEL_ADI_CM			(5 << 5) | 
|  |  | 
|  | #define ADV7842_OP_CH_SEL_GBR				(0 << 5) | 
|  | #define ADV7842_OP_CH_SEL_GRB				(1 << 5) | 
|  | #define ADV7842_OP_CH_SEL_BGR				(2 << 5) | 
|  | #define ADV7842_OP_CH_SEL_RGB				(3 << 5) | 
|  | #define ADV7842_OP_CH_SEL_BRG				(4 << 5) | 
|  | #define ADV7842_OP_CH_SEL_RBG				(5 << 5) | 
|  |  | 
|  | #define ADV7842_OP_SWAP_CB_CR				(1 << 0) | 
|  |  | 
|  | #define ADV7842_MAX_ADDRS (3) | 
|  |  | 
|  | /* | 
|  | ********************************************************************** | 
|  | * | 
|  | *  Arrays with configuration parameters for the ADV7842 | 
|  | * | 
|  | ********************************************************************** | 
|  | */ | 
|  |  | 
|  | struct adv7842_format_info { | 
|  | u32 code; | 
|  | u8 op_ch_sel; | 
|  | bool rgb_out; | 
|  | bool swap_cb_cr; | 
|  | u8 op_format_sel; | 
|  | }; | 
|  |  | 
|  | struct adv7842_state { | 
|  | struct adv7842_platform_data pdata; | 
|  | struct v4l2_subdev sd; | 
|  | struct media_pad pads[ADV7842_PAD_SOURCE + 1]; | 
|  | struct v4l2_ctrl_handler hdl; | 
|  | enum adv7842_mode mode; | 
|  | struct v4l2_dv_timings timings; | 
|  | enum adv7842_vid_std_select vid_std_select; | 
|  |  | 
|  | const struct adv7842_format_info *format; | 
|  |  | 
|  | v4l2_std_id norm; | 
|  | struct { | 
|  | u8 edid[512]; | 
|  | u32 blocks; | 
|  | u32 present; | 
|  | } hdmi_edid; | 
|  | struct { | 
|  | u8 edid[128]; | 
|  | u32 blocks; | 
|  | u32 present; | 
|  | } vga_edid; | 
|  | struct v4l2_fract aspect_ratio; | 
|  | u32 rgb_quantization_range; | 
|  | bool is_cea_format; | 
|  | struct delayed_work delayed_work_enable_hotplug; | 
|  | bool restart_stdi_once; | 
|  | bool hdmi_port_a; | 
|  |  | 
|  | struct dentry *debugfs_dir; | 
|  | struct v4l2_debugfs_if *infoframes; | 
|  |  | 
|  | /* i2c clients */ | 
|  | struct i2c_client *i2c_sdp_io; | 
|  | struct i2c_client *i2c_sdp; | 
|  | struct i2c_client *i2c_cp; | 
|  | struct i2c_client *i2c_vdp; | 
|  | struct i2c_client *i2c_afe; | 
|  | struct i2c_client *i2c_hdmi; | 
|  | struct i2c_client *i2c_repeater; | 
|  | struct i2c_client *i2c_edid; | 
|  | struct i2c_client *i2c_infoframe; | 
|  | struct i2c_client *i2c_cec; | 
|  | struct i2c_client *i2c_avlink; | 
|  |  | 
|  | /* controls */ | 
|  | struct v4l2_ctrl *detect_tx_5v_ctrl; | 
|  | struct v4l2_ctrl *analog_sampling_phase_ctrl; | 
|  | struct v4l2_ctrl *free_run_color_ctrl_manual; | 
|  | struct v4l2_ctrl *free_run_color_ctrl; | 
|  | struct v4l2_ctrl *rgb_quantization_range_ctrl; | 
|  |  | 
|  | struct cec_adapter *cec_adap; | 
|  | u8   cec_addr[ADV7842_MAX_ADDRS]; | 
|  | u8   cec_valid_addrs; | 
|  | bool cec_enabled_adap; | 
|  | }; | 
|  |  | 
|  | /* Unsupported timings. This device cannot support 720p30. */ | 
|  | static const struct v4l2_dv_timings adv7842_timings_exceptions[] = { | 
|  | V4L2_DV_BT_CEA_1280X720P30, | 
|  | { } | 
|  | }; | 
|  |  | 
|  | static bool adv7842_check_dv_timings(const struct v4l2_dv_timings *t, void *hdl) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; adv7842_timings_exceptions[i].bt.width; i++) | 
|  | if (v4l2_match_dv_timings(t, adv7842_timings_exceptions + i, 0, false)) | 
|  | return false; | 
|  | return true; | 
|  | } | 
|  |  | 
|  | struct adv7842_video_standards { | 
|  | struct v4l2_dv_timings timings; | 
|  | u8 vid_std; | 
|  | u8 v_freq; | 
|  | }; | 
|  |  | 
|  | /* sorted by number of lines */ | 
|  | static const struct adv7842_video_standards adv7842_prim_mode_comp[] = { | 
|  | /* { V4L2_DV_BT_CEA_720X480P59_94, 0x0a, 0x00 }, TODO flickering */ | 
|  | { V4L2_DV_BT_CEA_720X576P50, 0x0b, 0x00 }, | 
|  | { V4L2_DV_BT_CEA_1280X720P50, 0x19, 0x01 }, | 
|  | { V4L2_DV_BT_CEA_1280X720P60, 0x19, 0x00 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P24, 0x1e, 0x04 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P25, 0x1e, 0x03 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P30, 0x1e, 0x02 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P50, 0x1e, 0x01 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P60, 0x1e, 0x00 }, | 
|  | /* TODO add 1920x1080P60_RB (CVT timing) */ | 
|  | { }, | 
|  | }; | 
|  |  | 
|  | /* sorted by number of lines */ | 
|  | static const struct adv7842_video_standards adv7842_prim_mode_gr[] = { | 
|  | { V4L2_DV_BT_DMT_640X480P60, 0x08, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_640X480P72, 0x09, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_640X480P75, 0x0a, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_640X480P85, 0x0b, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P56, 0x00, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P60, 0x01, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P72, 0x02, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P75, 0x03, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P85, 0x04, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P60, 0x0c, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P70, 0x0d, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P75, 0x0e, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P85, 0x0f, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1280X1024P60, 0x05, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1280X1024P75, 0x06, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1360X768P60, 0x12, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1366X768P60, 0x13, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1400X1050P60, 0x14, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1400X1050P75, 0x15, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1600X1200P60, 0x16, 0x00 }, /* TODO not tested */ | 
|  | /* TODO add 1600X1200P60_RB (not a DMT timing) */ | 
|  | { V4L2_DV_BT_DMT_1680X1050P60, 0x18, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1920X1200P60_RB, 0x19, 0x00 }, /* TODO not tested */ | 
|  | { }, | 
|  | }; | 
|  |  | 
|  | /* sorted by number of lines */ | 
|  | static const struct adv7842_video_standards adv7842_prim_mode_hdmi_comp[] = { | 
|  | { V4L2_DV_BT_CEA_720X480P59_94, 0x0a, 0x00 }, | 
|  | { V4L2_DV_BT_CEA_720X576P50, 0x0b, 0x00 }, | 
|  | { V4L2_DV_BT_CEA_1280X720P50, 0x13, 0x01 }, | 
|  | { V4L2_DV_BT_CEA_1280X720P60, 0x13, 0x00 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P24, 0x1e, 0x04 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P25, 0x1e, 0x03 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P30, 0x1e, 0x02 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P50, 0x1e, 0x01 }, | 
|  | { V4L2_DV_BT_CEA_1920X1080P60, 0x1e, 0x00 }, | 
|  | { }, | 
|  | }; | 
|  |  | 
|  | /* sorted by number of lines */ | 
|  | static const struct adv7842_video_standards adv7842_prim_mode_hdmi_gr[] = { | 
|  | { V4L2_DV_BT_DMT_640X480P60, 0x08, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_640X480P72, 0x09, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_640X480P75, 0x0a, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_640X480P85, 0x0b, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P56, 0x00, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P60, 0x01, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P72, 0x02, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P75, 0x03, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_800X600P85, 0x04, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P60, 0x0c, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P70, 0x0d, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P75, 0x0e, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1024X768P85, 0x0f, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1280X1024P60, 0x05, 0x00 }, | 
|  | { V4L2_DV_BT_DMT_1280X1024P75, 0x06, 0x00 }, | 
|  | { }, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_event adv7842_ev_fmt = { | 
|  | .type = V4L2_EVENT_SOURCE_CHANGE, | 
|  | .u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION, | 
|  | }; | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static inline struct adv7842_state *to_state(struct v4l2_subdev *sd) | 
|  | { | 
|  | return container_of(sd, struct adv7842_state, sd); | 
|  | } | 
|  |  | 
|  | static inline struct v4l2_subdev *to_sd(struct v4l2_ctrl *ctrl) | 
|  | { | 
|  | return &container_of(ctrl->handler, struct adv7842_state, hdl)->sd; | 
|  | } | 
|  |  | 
|  | static inline unsigned htotal(const struct v4l2_bt_timings *t) | 
|  | { | 
|  | return V4L2_DV_BT_FRAME_WIDTH(t); | 
|  | } | 
|  |  | 
|  | static inline unsigned vtotal(const struct v4l2_bt_timings *t) | 
|  | { | 
|  | return V4L2_DV_BT_FRAME_HEIGHT(t); | 
|  | } | 
|  |  | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static s32 adv_smbus_read_byte_data_check(struct i2c_client *client, | 
|  | u8 command, bool check) | 
|  | { | 
|  | union i2c_smbus_data data; | 
|  |  | 
|  | if (!i2c_smbus_xfer(client->adapter, client->addr, client->flags, | 
|  | I2C_SMBUS_READ, command, | 
|  | I2C_SMBUS_BYTE_DATA, &data)) | 
|  | return data.byte; | 
|  | if (check) | 
|  | v4l_err(client, "error reading %02x, %02x\n", | 
|  | client->addr, command); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | static s32 adv_smbus_read_byte_data(struct i2c_client *client, u8 command) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < 3; i++) { | 
|  | int ret = adv_smbus_read_byte_data_check(client, command, true); | 
|  |  | 
|  | if (ret >= 0) { | 
|  | if (i) | 
|  | v4l_err(client, "read ok after %d retries\n", i); | 
|  | return ret; | 
|  | } | 
|  | } | 
|  | v4l_err(client, "read failed\n"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | static s32 adv_smbus_write_byte_data(struct i2c_client *client, | 
|  | u8 command, u8 value) | 
|  | { | 
|  | union i2c_smbus_data data; | 
|  | int err; | 
|  | int i; | 
|  |  | 
|  | data.byte = value; | 
|  | for (i = 0; i < 3; i++) { | 
|  | err = i2c_smbus_xfer(client->adapter, client->addr, | 
|  | client->flags, | 
|  | I2C_SMBUS_WRITE, command, | 
|  | I2C_SMBUS_BYTE_DATA, &data); | 
|  | if (!err) | 
|  | break; | 
|  | } | 
|  | if (err < 0) | 
|  | v4l_err(client, "error writing %02x, %02x, %02x\n", | 
|  | client->addr, command, value); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static void adv_smbus_write_byte_no_check(struct i2c_client *client, | 
|  | u8 command, u8 value) | 
|  | { | 
|  | union i2c_smbus_data data; | 
|  | data.byte = value; | 
|  |  | 
|  | i2c_smbus_xfer(client->adapter, client->addr, | 
|  | client->flags, | 
|  | I2C_SMBUS_WRITE, command, | 
|  | I2C_SMBUS_BYTE_DATA, &data); | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static inline int io_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(client, reg); | 
|  | } | 
|  |  | 
|  | static inline int io_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(client, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int io_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return io_write(sd, reg, (io_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int io_write_clr_set(struct v4l2_subdev *sd, | 
|  | u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return io_write(sd, reg, (io_read(sd, reg) & ~mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int avlink_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_avlink, reg); | 
|  | } | 
|  |  | 
|  | static inline int avlink_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_avlink, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int cec_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_cec, reg); | 
|  | } | 
|  |  | 
|  | static inline int cec_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_cec, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int cec_write_clr_set(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return cec_write(sd, reg, (cec_read(sd, reg) & ~mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int infoframe_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_infoframe, reg); | 
|  | } | 
|  |  | 
|  | static inline int infoframe_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_infoframe, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int sdp_io_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_sdp_io, reg); | 
|  | } | 
|  |  | 
|  | static inline int sdp_io_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_sdp_io, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int sdp_io_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return sdp_io_write(sd, reg, (sdp_io_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int sdp_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_sdp, reg); | 
|  | } | 
|  |  | 
|  | static inline int sdp_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_sdp, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int sdp_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return sdp_write(sd, reg, (sdp_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int afe_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_afe, reg); | 
|  | } | 
|  |  | 
|  | static inline int afe_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_afe, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int afe_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return afe_write(sd, reg, (afe_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int rep_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_repeater, reg); | 
|  | } | 
|  |  | 
|  | static inline int rep_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_repeater, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int rep_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return rep_write(sd, reg, (rep_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int edid_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_edid, reg); | 
|  | } | 
|  |  | 
|  | static inline int edid_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_edid, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int hdmi_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_hdmi, reg); | 
|  | } | 
|  |  | 
|  | static inline int hdmi_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_hdmi, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int hdmi_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return hdmi_write(sd, reg, (hdmi_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int cp_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_cp, reg); | 
|  | } | 
|  |  | 
|  | static inline int cp_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_cp, reg, val); | 
|  | } | 
|  |  | 
|  | static inline int cp_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val) | 
|  | { | 
|  | return cp_write(sd, reg, (cp_read(sd, reg) & mask) | val); | 
|  | } | 
|  |  | 
|  | static inline int vdp_read(struct v4l2_subdev *sd, u8 reg) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_read_byte_data(state->i2c_vdp, reg); | 
|  | } | 
|  |  | 
|  | static inline int vdp_write(struct v4l2_subdev *sd, u8 reg, u8 val) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return adv_smbus_write_byte_data(state->i2c_vdp, reg, val); | 
|  | } | 
|  |  | 
|  | static void main_reset(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s:\n", __func__); | 
|  |  | 
|  | adv_smbus_write_byte_no_check(client, 0xff, 0x80); | 
|  |  | 
|  | mdelay(5); | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------------- | 
|  | * Format helpers | 
|  | */ | 
|  |  | 
|  | static const struct adv7842_format_info adv7842_formats[] = { | 
|  | { MEDIA_BUS_FMT_RGB888_1X24, ADV7842_OP_CH_SEL_RGB, true, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_444 | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_YUYV8_2X8, ADV7842_OP_CH_SEL_RGB, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422 | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_YVYU8_2X8, ADV7842_OP_CH_SEL_RGB, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422 | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_YUYV10_2X10, ADV7842_OP_CH_SEL_RGB, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422 | ADV7842_OP_FORMAT_SEL_10BIT }, | 
|  | { MEDIA_BUS_FMT_YVYU10_2X10, ADV7842_OP_CH_SEL_RGB, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422 | ADV7842_OP_FORMAT_SEL_10BIT }, | 
|  | { MEDIA_BUS_FMT_YUYV12_2X12, ADV7842_OP_CH_SEL_RGB, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422 | ADV7842_OP_FORMAT_SEL_12BIT }, | 
|  | { MEDIA_BUS_FMT_YVYU12_2X12, ADV7842_OP_CH_SEL_RGB, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422 | ADV7842_OP_FORMAT_SEL_12BIT }, | 
|  | { MEDIA_BUS_FMT_UYVY8_1X16, ADV7842_OP_CH_SEL_RBG, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_VYUY8_1X16, ADV7842_OP_CH_SEL_RBG, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_YUYV8_1X16, ADV7842_OP_CH_SEL_RGB, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_YVYU8_1X16, ADV7842_OP_CH_SEL_RGB, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_8BIT }, | 
|  | { MEDIA_BUS_FMT_UYVY10_1X20, ADV7842_OP_CH_SEL_RBG, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_10BIT }, | 
|  | { MEDIA_BUS_FMT_VYUY10_1X20, ADV7842_OP_CH_SEL_RBG, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_10BIT }, | 
|  | { MEDIA_BUS_FMT_YUYV10_1X20, ADV7842_OP_CH_SEL_RGB, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_10BIT }, | 
|  | { MEDIA_BUS_FMT_YVYU10_1X20, ADV7842_OP_CH_SEL_RGB, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_10BIT }, | 
|  | { MEDIA_BUS_FMT_UYVY12_1X24, ADV7842_OP_CH_SEL_RBG, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_12BIT }, | 
|  | { MEDIA_BUS_FMT_VYUY12_1X24, ADV7842_OP_CH_SEL_RBG, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_12BIT }, | 
|  | { MEDIA_BUS_FMT_YUYV12_1X24, ADV7842_OP_CH_SEL_RGB, false, false, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_12BIT }, | 
|  | { MEDIA_BUS_FMT_YVYU12_1X24, ADV7842_OP_CH_SEL_RGB, false, true, | 
|  | ADV7842_OP_MODE_SEL_SDR_422_2X | ADV7842_OP_FORMAT_SEL_12BIT }, | 
|  | }; | 
|  |  | 
|  | static const struct adv7842_format_info * | 
|  | adv7842_format_info(struct adv7842_state *state, u32 code) | 
|  | { | 
|  | unsigned int i; | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(adv7842_formats); ++i) { | 
|  | if (adv7842_formats[i].code == code) | 
|  | return &adv7842_formats[i]; | 
|  | } | 
|  |  | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static inline bool is_analog_input(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return ((state->mode == ADV7842_MODE_RGB) || | 
|  | (state->mode == ADV7842_MODE_COMP)); | 
|  | } | 
|  |  | 
|  | static inline bool is_digital_input(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | return state->mode == ADV7842_MODE_HDMI; | 
|  | } | 
|  |  | 
|  | static const struct v4l2_dv_timings_cap adv7842_timings_cap_analog = { | 
|  | .type = V4L2_DV_BT_656_1120, | 
|  | /* keep this initialization for compatibility with GCC < 4.4.6 */ | 
|  | .reserved = { 0 }, | 
|  | V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 170000000, | 
|  | V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | | 
|  | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, | 
|  | V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | | 
|  | V4L2_DV_BT_CAP_CUSTOM) | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_dv_timings_cap adv7842_timings_cap_digital = { | 
|  | .type = V4L2_DV_BT_656_1120, | 
|  | /* keep this initialization for compatibility with GCC < 4.4.6 */ | 
|  | .reserved = { 0 }, | 
|  | V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 225000000, | 
|  | V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | | 
|  | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, | 
|  | V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | | 
|  | V4L2_DV_BT_CAP_CUSTOM) | 
|  | }; | 
|  |  | 
|  | static inline const struct v4l2_dv_timings_cap * | 
|  | adv7842_get_dv_timings_cap(struct v4l2_subdev *sd) | 
|  | { | 
|  | return is_digital_input(sd) ? &adv7842_timings_cap_digital : | 
|  | &adv7842_timings_cap_analog; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static u16 adv7842_read_cable_det(struct v4l2_subdev *sd) | 
|  | { | 
|  | u8 reg = io_read(sd, 0x6f); | 
|  | u16 val = 0; | 
|  |  | 
|  | if (reg & 0x02) | 
|  | val |= 1; /* port A */ | 
|  | if (reg & 0x01) | 
|  | val |= 2; /* port B */ | 
|  | return val; | 
|  | } | 
|  |  | 
|  | static void adv7842_delayed_work_enable_hotplug(struct work_struct *work) | 
|  | { | 
|  | struct delayed_work *dwork = to_delayed_work(work); | 
|  | struct adv7842_state *state = container_of(dwork, | 
|  | struct adv7842_state, delayed_work_enable_hotplug); | 
|  | struct v4l2_subdev *sd = &state->sd; | 
|  | int present = state->hdmi_edid.present; | 
|  | u8 mask = 0; | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: enable hotplug on ports: 0x%x\n", | 
|  | __func__, present); | 
|  |  | 
|  | if (present & (0x04 << ADV7842_EDID_PORT_A)) | 
|  | mask |= 0x20; | 
|  | if (present & (0x04 << ADV7842_EDID_PORT_B)) | 
|  | mask |= 0x10; | 
|  | io_write_and_or(sd, 0x20, 0xcf, mask); | 
|  | } | 
|  |  | 
|  | static int edid_write_vga_segment(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | const u8 *edid = state->vga_edid.edid; | 
|  | u32 blocks = state->vga_edid.blocks; | 
|  | int err = 0; | 
|  | int i; | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: write EDID on VGA port\n", __func__); | 
|  |  | 
|  | if (!state->vga_edid.present) | 
|  | return 0; | 
|  |  | 
|  | /* HPA disable on port A and B */ | 
|  | io_write_and_or(sd, 0x20, 0xcf, 0x00); | 
|  |  | 
|  | /* Disable I2C access to internal EDID ram from VGA DDC port */ | 
|  | rep_write_and_or(sd, 0x7f, 0x7f, 0x00); | 
|  |  | 
|  | /* edid segment pointer '1' for VGA port */ | 
|  | rep_write_and_or(sd, 0x77, 0xef, 0x10); | 
|  |  | 
|  | for (i = 0; !err && i < blocks * 128; i += I2C_SMBUS_BLOCK_MAX) | 
|  | err = i2c_smbus_write_i2c_block_data(state->i2c_edid, i, | 
|  | I2C_SMBUS_BLOCK_MAX, | 
|  | edid + i); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | /* Calculates the checksums and enables I2C access | 
|  | * to internal EDID ram from VGA DDC port. | 
|  | */ | 
|  | rep_write_and_or(sd, 0x7f, 0x7f, 0x80); | 
|  |  | 
|  | for (i = 0; i < 1000; i++) { | 
|  | if (rep_read(sd, 0x79) & 0x20) | 
|  | break; | 
|  | mdelay(1); | 
|  | } | 
|  | if (i == 1000) { | 
|  | v4l_err(client, "error enabling edid on VGA port\n"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | /* enable hotplug after 200 ms */ | 
|  | schedule_delayed_work(&state->delayed_work_enable_hotplug, HZ / 5); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int edid_write_hdmi_segment(struct v4l2_subdev *sd, u8 port) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | const u8 *edid = state->hdmi_edid.edid; | 
|  | u32 blocks = state->hdmi_edid.blocks; | 
|  | unsigned int spa_loc; | 
|  | u16 pa, parent_pa; | 
|  | int err = 0; | 
|  | int i; | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: write EDID on port %c\n", | 
|  | __func__, (port == ADV7842_EDID_PORT_A) ? 'A' : 'B'); | 
|  |  | 
|  | /* HPA disable on port A and B */ | 
|  | io_write_and_or(sd, 0x20, 0xcf, 0x00); | 
|  |  | 
|  | /* Disable I2C access to internal EDID ram from HDMI DDC ports */ | 
|  | rep_write_and_or(sd, 0x77, 0xf3, 0x00); | 
|  |  | 
|  | if (!state->hdmi_edid.present) { | 
|  | cec_phys_addr_invalidate(state->cec_adap); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | pa = v4l2_get_edid_phys_addr(edid, blocks * 128, &spa_loc); | 
|  | err = v4l2_phys_addr_validate(pa, &parent_pa, NULL); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | if (!spa_loc) { | 
|  | /* | 
|  | * There is no SPA, so just set spa_loc to 128 and pa to whatever | 
|  | * data is there. | 
|  | */ | 
|  | spa_loc = 128; | 
|  | pa = (edid[spa_loc] << 8) | edid[spa_loc + 1]; | 
|  | } | 
|  |  | 
|  |  | 
|  | for (i = 0; !err && i < blocks * 128; i += I2C_SMBUS_BLOCK_MAX) { | 
|  | /* set edid segment pointer for HDMI ports */ | 
|  | if (i % 256 == 0) | 
|  | rep_write_and_or(sd, 0x77, 0xef, i >= 256 ? 0x10 : 0x00); | 
|  | err = i2c_smbus_write_i2c_block_data(state->i2c_edid, i, | 
|  | I2C_SMBUS_BLOCK_MAX, edid + i); | 
|  | } | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | if (port == ADV7842_EDID_PORT_A) { | 
|  | rep_write(sd, 0x72, pa >> 8); | 
|  | rep_write(sd, 0x73, pa & 0xff); | 
|  | } else { | 
|  | rep_write(sd, 0x74, pa >> 8); | 
|  | rep_write(sd, 0x75, pa & 0xff); | 
|  | } | 
|  | rep_write(sd, 0x76, spa_loc & 0xff); | 
|  | rep_write_and_or(sd, 0x77, 0xbf, (spa_loc >> 2) & 0x40); | 
|  |  | 
|  | /* Calculates the checksums and enables I2C access to internal | 
|  | * EDID ram from HDMI DDC ports | 
|  | */ | 
|  | rep_write_and_or(sd, 0x77, 0xf3, state->hdmi_edid.present); | 
|  |  | 
|  | for (i = 0; i < 1000; i++) { | 
|  | if (rep_read(sd, 0x7d) & state->hdmi_edid.present) | 
|  | break; | 
|  | mdelay(1); | 
|  | } | 
|  | if (i == 1000) { | 
|  | v4l_err(client, "error enabling edid on port %c\n", | 
|  | (port == ADV7842_EDID_PORT_A) ? 'A' : 'B'); | 
|  | return -EIO; | 
|  | } | 
|  | cec_s_phys_addr(state->cec_adap, parent_pa, false); | 
|  |  | 
|  | /* enable hotplug after 200 ms */ | 
|  | schedule_delayed_work(&state->delayed_work_enable_hotplug, HZ / 5); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | #ifdef CONFIG_VIDEO_ADV_DEBUG | 
|  | static void adv7842_inv_register(struct v4l2_subdev *sd) | 
|  | { | 
|  | v4l2_info(sd, "0x000-0x0ff: IO Map\n"); | 
|  | v4l2_info(sd, "0x100-0x1ff: AVLink Map\n"); | 
|  | v4l2_info(sd, "0x200-0x2ff: CEC Map\n"); | 
|  | v4l2_info(sd, "0x300-0x3ff: InfoFrame Map\n"); | 
|  | v4l2_info(sd, "0x400-0x4ff: SDP_IO Map\n"); | 
|  | v4l2_info(sd, "0x500-0x5ff: SDP Map\n"); | 
|  | v4l2_info(sd, "0x600-0x6ff: AFE Map\n"); | 
|  | v4l2_info(sd, "0x700-0x7ff: Repeater Map\n"); | 
|  | v4l2_info(sd, "0x800-0x8ff: EDID Map\n"); | 
|  | v4l2_info(sd, "0x900-0x9ff: HDMI Map\n"); | 
|  | v4l2_info(sd, "0xa00-0xaff: CP Map\n"); | 
|  | v4l2_info(sd, "0xb00-0xbff: VDP Map\n"); | 
|  | } | 
|  |  | 
|  | static int adv7842_g_register(struct v4l2_subdev *sd, | 
|  | struct v4l2_dbg_register *reg) | 
|  | { | 
|  | reg->size = 1; | 
|  | switch (reg->reg >> 8) { | 
|  | case 0: | 
|  | reg->val = io_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 1: | 
|  | reg->val = avlink_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 2: | 
|  | reg->val = cec_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 3: | 
|  | reg->val = infoframe_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 4: | 
|  | reg->val = sdp_io_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 5: | 
|  | reg->val = sdp_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 6: | 
|  | reg->val = afe_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 7: | 
|  | reg->val = rep_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 8: | 
|  | reg->val = edid_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 9: | 
|  | reg->val = hdmi_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 0xa: | 
|  | reg->val = cp_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | case 0xb: | 
|  | reg->val = vdp_read(sd, reg->reg & 0xff); | 
|  | break; | 
|  | default: | 
|  | v4l2_info(sd, "Register %03llx not supported\n", reg->reg); | 
|  | adv7842_inv_register(sd); | 
|  | break; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_s_register(struct v4l2_subdev *sd, | 
|  | const struct v4l2_dbg_register *reg) | 
|  | { | 
|  | u8 val = reg->val & 0xff; | 
|  |  | 
|  | switch (reg->reg >> 8) { | 
|  | case 0: | 
|  | io_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 1: | 
|  | avlink_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 2: | 
|  | cec_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 3: | 
|  | infoframe_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 4: | 
|  | sdp_io_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 5: | 
|  | sdp_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 6: | 
|  | afe_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 7: | 
|  | rep_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 8: | 
|  | edid_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 9: | 
|  | hdmi_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 0xa: | 
|  | cp_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | case 0xb: | 
|  | vdp_write(sd, reg->reg & 0xff, val); | 
|  | break; | 
|  | default: | 
|  | v4l2_info(sd, "Register %03llx not supported\n", reg->reg); | 
|  | adv7842_inv_register(sd); | 
|  | break; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | static int adv7842_s_detect_tx_5v_ctrl(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | u16 cable_det = adv7842_read_cable_det(sd); | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s: 0x%x\n", __func__, cable_det); | 
|  |  | 
|  | return v4l2_ctrl_s_ctrl(state->detect_tx_5v_ctrl, cable_det); | 
|  | } | 
|  |  | 
|  | static int find_and_set_predefined_video_timings(struct v4l2_subdev *sd, | 
|  | u8 prim_mode, | 
|  | const struct adv7842_video_standards *predef_vid_timings, | 
|  | const struct v4l2_dv_timings *timings) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; predef_vid_timings[i].timings.bt.width; i++) { | 
|  | if (!v4l2_match_dv_timings(timings, &predef_vid_timings[i].timings, | 
|  | is_digital_input(sd) ? 250000 : 1000000, false)) | 
|  | continue; | 
|  | /* video std */ | 
|  | io_write(sd, 0x00, predef_vid_timings[i].vid_std); | 
|  | /* v_freq and prim mode */ | 
|  | io_write(sd, 0x01, (predef_vid_timings[i].v_freq << 4) + prim_mode); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | static int configure_predefined_video_timings(struct v4l2_subdev *sd, | 
|  | struct v4l2_dv_timings *timings) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | int err; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s\n", __func__); | 
|  |  | 
|  | /* reset to default values */ | 
|  | io_write(sd, 0x16, 0x43); | 
|  | io_write(sd, 0x17, 0x5a); | 
|  | /* disable embedded syncs for auto graphics mode */ | 
|  | cp_write_and_or(sd, 0x81, 0xef, 0x00); | 
|  | cp_write(sd, 0x26, 0x00); | 
|  | cp_write(sd, 0x27, 0x00); | 
|  | cp_write(sd, 0x28, 0x00); | 
|  | cp_write(sd, 0x29, 0x00); | 
|  | cp_write(sd, 0x8f, 0x40); | 
|  | cp_write(sd, 0x90, 0x00); | 
|  | cp_write(sd, 0xa5, 0x00); | 
|  | cp_write(sd, 0xa6, 0x00); | 
|  | cp_write(sd, 0xa7, 0x00); | 
|  | cp_write(sd, 0xab, 0x00); | 
|  | cp_write(sd, 0xac, 0x00); | 
|  |  | 
|  | switch (state->mode) { | 
|  | case ADV7842_MODE_COMP: | 
|  | case ADV7842_MODE_RGB: | 
|  | err = find_and_set_predefined_video_timings(sd, | 
|  | 0x01, adv7842_prim_mode_comp, timings); | 
|  | if (err) | 
|  | err = find_and_set_predefined_video_timings(sd, | 
|  | 0x02, adv7842_prim_mode_gr, timings); | 
|  | break; | 
|  | case ADV7842_MODE_HDMI: | 
|  | err = find_and_set_predefined_video_timings(sd, | 
|  | 0x05, adv7842_prim_mode_hdmi_comp, timings); | 
|  | if (err) | 
|  | err = find_and_set_predefined_video_timings(sd, | 
|  | 0x06, adv7842_prim_mode_hdmi_gr, timings); | 
|  | break; | 
|  | default: | 
|  | v4l2_dbg(2, debug, sd, "%s: Unknown mode %d\n", | 
|  | __func__, state->mode); | 
|  | err = -1; | 
|  | break; | 
|  | } | 
|  |  | 
|  |  | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static void configure_custom_video_timings(struct v4l2_subdev *sd, | 
|  | const struct v4l2_bt_timings *bt) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | u32 width = htotal(bt); | 
|  | u32 height = vtotal(bt); | 
|  | u16 cp_start_sav = bt->hsync + bt->hbackporch - 4; | 
|  | u16 cp_start_eav = width - bt->hfrontporch; | 
|  | u16 cp_start_vbi = height - bt->vfrontporch + 1; | 
|  | u16 cp_end_vbi = bt->vsync + bt->vbackporch + 1; | 
|  | u16 ch1_fr_ll = (((u32)bt->pixelclock / 100) > 0) ? | 
|  | ((width * (ADV7842_fsc / 100)) / ((u32)bt->pixelclock / 100)) : 0; | 
|  | const u8 pll[2] = { | 
|  | 0xc0 | ((width >> 8) & 0x1f), | 
|  | width & 0xff | 
|  | }; | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s\n", __func__); | 
|  |  | 
|  | switch (state->mode) { | 
|  | case ADV7842_MODE_COMP: | 
|  | case ADV7842_MODE_RGB: | 
|  | /* auto graphics */ | 
|  | io_write(sd, 0x00, 0x07); /* video std */ | 
|  | io_write(sd, 0x01, 0x02); /* prim mode */ | 
|  | /* enable embedded syncs for auto graphics mode */ | 
|  | cp_write_and_or(sd, 0x81, 0xef, 0x10); | 
|  |  | 
|  | /* Should only be set in auto-graphics mode [REF_02, p. 91-92] */ | 
|  | /* setup PLL_DIV_MAN_EN and PLL_DIV_RATIO */ | 
|  | /* IO-map reg. 0x16 and 0x17 should be written in sequence */ | 
|  | if (i2c_smbus_write_i2c_block_data(client, 0x16, 2, pll)) { | 
|  | v4l2_err(sd, "writing to reg 0x16 and 0x17 failed\n"); | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* active video - horizontal timing */ | 
|  | cp_write(sd, 0x26, (cp_start_sav >> 8) & 0xf); | 
|  | cp_write(sd, 0x27, (cp_start_sav & 0xff)); | 
|  | cp_write(sd, 0x28, (cp_start_eav >> 8) & 0xf); | 
|  | cp_write(sd, 0x29, (cp_start_eav & 0xff)); | 
|  |  | 
|  | /* active video - vertical timing */ | 
|  | cp_write(sd, 0xa5, (cp_start_vbi >> 4) & 0xff); | 
|  | cp_write(sd, 0xa6, ((cp_start_vbi & 0xf) << 4) | | 
|  | ((cp_end_vbi >> 8) & 0xf)); | 
|  | cp_write(sd, 0xa7, cp_end_vbi & 0xff); | 
|  | break; | 
|  | case ADV7842_MODE_HDMI: | 
|  | /* set default prim_mode/vid_std for HDMI | 
|  | according to [REF_03, c. 4.2] */ | 
|  | io_write(sd, 0x00, 0x02); /* video std */ | 
|  | io_write(sd, 0x01, 0x06); /* prim mode */ | 
|  | break; | 
|  | default: | 
|  | v4l2_dbg(2, debug, sd, "%s: Unknown mode %d\n", | 
|  | __func__, state->mode); | 
|  | break; | 
|  | } | 
|  |  | 
|  | cp_write(sd, 0x8f, (ch1_fr_ll >> 8) & 0x7); | 
|  | cp_write(sd, 0x90, ch1_fr_ll & 0xff); | 
|  | cp_write(sd, 0xab, (height >> 4) & 0xff); | 
|  | cp_write(sd, 0xac, (height & 0x0f) << 4); | 
|  | } | 
|  |  | 
|  | static void adv7842_set_offset(struct v4l2_subdev *sd, bool auto_offset, u16 offset_a, u16 offset_b, u16 offset_c) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | u8 offset_buf[4]; | 
|  |  | 
|  | if (auto_offset) { | 
|  | offset_a = 0x3ff; | 
|  | offset_b = 0x3ff; | 
|  | offset_c = 0x3ff; | 
|  | } | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: %s offset: a = 0x%x, b = 0x%x, c = 0x%x\n", | 
|  | __func__, auto_offset ? "Auto" : "Manual", | 
|  | offset_a, offset_b, offset_c); | 
|  |  | 
|  | offset_buf[0]= (cp_read(sd, 0x77) & 0xc0) | ((offset_a & 0x3f0) >> 4); | 
|  | offset_buf[1] = ((offset_a & 0x00f) << 4) | ((offset_b & 0x3c0) >> 6); | 
|  | offset_buf[2] = ((offset_b & 0x03f) << 2) | ((offset_c & 0x300) >> 8); | 
|  | offset_buf[3] = offset_c & 0x0ff; | 
|  |  | 
|  | /* Registers must be written in this order with no i2c access in between */ | 
|  | if (i2c_smbus_write_i2c_block_data(state->i2c_cp, 0x77, 4, offset_buf)) | 
|  | v4l2_err(sd, "%s: i2c error writing to CP reg 0x77, 0x78, 0x79, 0x7a\n", __func__); | 
|  | } | 
|  |  | 
|  | static void adv7842_set_gain(struct v4l2_subdev *sd, bool auto_gain, u16 gain_a, u16 gain_b, u16 gain_c) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | u8 gain_buf[4]; | 
|  | u8 gain_man = 1; | 
|  | u8 agc_mode_man = 1; | 
|  |  | 
|  | if (auto_gain) { | 
|  | gain_man = 0; | 
|  | agc_mode_man = 0; | 
|  | gain_a = 0x100; | 
|  | gain_b = 0x100; | 
|  | gain_c = 0x100; | 
|  | } | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: %s gain: a = 0x%x, b = 0x%x, c = 0x%x\n", | 
|  | __func__, auto_gain ? "Auto" : "Manual", | 
|  | gain_a, gain_b, gain_c); | 
|  |  | 
|  | gain_buf[0] = ((gain_man << 7) | (agc_mode_man << 6) | ((gain_a & 0x3f0) >> 4)); | 
|  | gain_buf[1] = (((gain_a & 0x00f) << 4) | ((gain_b & 0x3c0) >> 6)); | 
|  | gain_buf[2] = (((gain_b & 0x03f) << 2) | ((gain_c & 0x300) >> 8)); | 
|  | gain_buf[3] = ((gain_c & 0x0ff)); | 
|  |  | 
|  | /* Registers must be written in this order with no i2c access in between */ | 
|  | if (i2c_smbus_write_i2c_block_data(state->i2c_cp, 0x73, 4, gain_buf)) | 
|  | v4l2_err(sd, "%s: i2c error writing to CP reg 0x73, 0x74, 0x75, 0x76\n", __func__); | 
|  | } | 
|  |  | 
|  | static void set_rgb_quantization_range(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | bool rgb_output = io_read(sd, 0x02) & 0x02; | 
|  | bool hdmi_signal = hdmi_read(sd, 0x05) & 0x80; | 
|  | u8 y = HDMI_COLORSPACE_RGB; | 
|  |  | 
|  | if (hdmi_signal && (io_read(sd, 0x60) & 1)) | 
|  | y = infoframe_read(sd, 0x01) >> 5; | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: RGB quantization range: %d, RGB out: %d, HDMI: %d\n", | 
|  | __func__, state->rgb_quantization_range, | 
|  | rgb_output, hdmi_signal); | 
|  |  | 
|  | adv7842_set_gain(sd, true, 0x0, 0x0, 0x0); | 
|  | adv7842_set_offset(sd, true, 0x0, 0x0, 0x0); | 
|  | io_write_clr_set(sd, 0x02, 0x04, rgb_output ? 0 : 4); | 
|  |  | 
|  | switch (state->rgb_quantization_range) { | 
|  | case V4L2_DV_RGB_RANGE_AUTO: | 
|  | if (state->mode == ADV7842_MODE_RGB) { | 
|  | /* Receiving analog RGB signal | 
|  | * Set RGB full range (0-255) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x10); | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_COMP) { | 
|  | /* Receiving analog YPbPr signal | 
|  | * Set automode */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0xf0); | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (hdmi_signal) { | 
|  | /* Receiving HDMI signal | 
|  | * Set automode */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0xf0); | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* Receiving DVI-D signal | 
|  | * ADV7842 selects RGB limited range regardless of | 
|  | * input format (CE/IT) in automatic mode */ | 
|  | if (state->timings.bt.flags & V4L2_DV_FL_IS_CE_VIDEO) { | 
|  | /* RGB limited range (16-235) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x00); | 
|  | } else { | 
|  | /* RGB full range (0-255) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x10); | 
|  |  | 
|  | if (is_digital_input(sd) && rgb_output) { | 
|  | adv7842_set_offset(sd, false, 0x40, 0x40, 0x40); | 
|  | } else { | 
|  | adv7842_set_gain(sd, false, 0xe0, 0xe0, 0xe0); | 
|  | adv7842_set_offset(sd, false, 0x70, 0x70, 0x70); | 
|  | } | 
|  | } | 
|  | break; | 
|  | case V4L2_DV_RGB_RANGE_LIMITED: | 
|  | if (state->mode == ADV7842_MODE_COMP) { | 
|  | /* YCrCb limited range (16-235) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x20); | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (y != HDMI_COLORSPACE_RGB) | 
|  | break; | 
|  |  | 
|  | /* RGB limited range (16-235) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x00); | 
|  |  | 
|  | break; | 
|  | case V4L2_DV_RGB_RANGE_FULL: | 
|  | if (state->mode == ADV7842_MODE_COMP) { | 
|  | /* YCrCb full range (0-255) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x60); | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (y != HDMI_COLORSPACE_RGB) | 
|  | break; | 
|  |  | 
|  | /* RGB full range (0-255) */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x10); | 
|  |  | 
|  | if (is_analog_input(sd) || hdmi_signal) | 
|  | break; | 
|  |  | 
|  | /* Adjust gain/offset for DVI-D signals only */ | 
|  | if (rgb_output) { | 
|  | adv7842_set_offset(sd, false, 0x40, 0x40, 0x40); | 
|  | } else { | 
|  | adv7842_set_gain(sd, false, 0xe0, 0xe0, 0xe0); | 
|  | adv7842_set_offset(sd, false, 0x70, 0x70, 0x70); | 
|  | } | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int adv7842_s_ctrl(struct v4l2_ctrl *ctrl) | 
|  | { | 
|  | struct v4l2_subdev *sd = to_sd(ctrl); | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | /* TODO SDP ctrls | 
|  | contrast/brightness/hue/free run is acting a bit strange, | 
|  | not sure if sdp csc is correct. | 
|  | */ | 
|  | switch (ctrl->id) { | 
|  | /* standard ctrls */ | 
|  | case V4L2_CID_BRIGHTNESS: | 
|  | cp_write(sd, 0x3c, ctrl->val); | 
|  | sdp_write(sd, 0x14, ctrl->val); | 
|  | /* ignore lsb sdp 0x17[3:2] */ | 
|  | return 0; | 
|  | case V4L2_CID_CONTRAST: | 
|  | cp_write(sd, 0x3a, ctrl->val); | 
|  | sdp_write(sd, 0x13, ctrl->val); | 
|  | /* ignore lsb sdp 0x17[1:0] */ | 
|  | return 0; | 
|  | case V4L2_CID_SATURATION: | 
|  | cp_write(sd, 0x3b, ctrl->val); | 
|  | sdp_write(sd, 0x15, ctrl->val); | 
|  | /* ignore lsb sdp 0x17[5:4] */ | 
|  | return 0; | 
|  | case V4L2_CID_HUE: | 
|  | cp_write(sd, 0x3d, ctrl->val); | 
|  | sdp_write(sd, 0x16, ctrl->val); | 
|  | /* ignore lsb sdp 0x17[7:6] */ | 
|  | return 0; | 
|  | /* custom ctrls */ | 
|  | case V4L2_CID_ADV_RX_ANALOG_SAMPLING_PHASE: | 
|  | afe_write(sd, 0xc8, ctrl->val); | 
|  | return 0; | 
|  | case V4L2_CID_ADV_RX_FREE_RUN_COLOR_MANUAL: | 
|  | cp_write_and_or(sd, 0xbf, ~0x04, (ctrl->val << 2)); | 
|  | sdp_write_and_or(sd, 0xdd, ~0x04, (ctrl->val << 2)); | 
|  | return 0; | 
|  | case V4L2_CID_ADV_RX_FREE_RUN_COLOR: { | 
|  | u8 R = (ctrl->val & 0xff0000) >> 16; | 
|  | u8 G = (ctrl->val & 0x00ff00) >> 8; | 
|  | u8 B = (ctrl->val & 0x0000ff); | 
|  | /* RGB -> YUV, numerical approximation */ | 
|  | int Y = 66 * R + 129 * G + 25 * B; | 
|  | int U = -38 * R - 74 * G + 112 * B; | 
|  | int V = 112 * R - 94 * G - 18 * B; | 
|  |  | 
|  | /* Scale down to 8 bits with rounding */ | 
|  | Y = (Y + 128) >> 8; | 
|  | U = (U + 128) >> 8; | 
|  | V = (V + 128) >> 8; | 
|  | /* make U,V positive */ | 
|  | Y += 16; | 
|  | U += 128; | 
|  | V += 128; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "R %x, G %x, B %x\n", R, G, B); | 
|  | v4l2_dbg(1, debug, sd, "Y %x, U %x, V %x\n", Y, U, V); | 
|  |  | 
|  | /* CP */ | 
|  | cp_write(sd, 0xc1, R); | 
|  | cp_write(sd, 0xc0, G); | 
|  | cp_write(sd, 0xc2, B); | 
|  | /* SDP */ | 
|  | sdp_write(sd, 0xde, Y); | 
|  | sdp_write(sd, 0xdf, (V & 0xf0) | ((U >> 4) & 0x0f)); | 
|  | return 0; | 
|  | } | 
|  | case V4L2_CID_DV_RX_RGB_RANGE: | 
|  | state->rgb_quantization_range = ctrl->val; | 
|  | set_rgb_quantization_range(sd); | 
|  | return 0; | 
|  | } | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static int adv7842_g_volatile_ctrl(struct v4l2_ctrl *ctrl) | 
|  | { | 
|  | struct v4l2_subdev *sd = to_sd(ctrl); | 
|  |  | 
|  | if (ctrl->id == V4L2_CID_DV_RX_IT_CONTENT_TYPE) { | 
|  | ctrl->val = V4L2_DV_IT_CONTENT_TYPE_NO_ITC; | 
|  | if ((io_read(sd, 0x60) & 1) && (infoframe_read(sd, 0x03) & 0x80)) | 
|  | ctrl->val = (infoframe_read(sd, 0x05) >> 4) & 3; | 
|  | return 0; | 
|  | } | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static inline bool no_power(struct v4l2_subdev *sd) | 
|  | { | 
|  | return io_read(sd, 0x0c) & 0x24; | 
|  | } | 
|  |  | 
|  | static inline bool no_cp_signal(struct v4l2_subdev *sd) | 
|  | { | 
|  | return ((cp_read(sd, 0xb5) & 0xd0) != 0xd0) || !(cp_read(sd, 0xb1) & 0x80); | 
|  | } | 
|  |  | 
|  | static inline bool is_hdmi(struct v4l2_subdev *sd) | 
|  | { | 
|  | return hdmi_read(sd, 0x05) & 0x80; | 
|  | } | 
|  |  | 
|  | static int adv7842_g_input_status(struct v4l2_subdev *sd, u32 *status) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | *status = 0; | 
|  |  | 
|  | if (io_read(sd, 0x0c) & 0x24) | 
|  | *status |= V4L2_IN_ST_NO_POWER; | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_SDP) { | 
|  | /* status from SDP block */ | 
|  | if (!(sdp_read(sd, 0x5A) & 0x01)) | 
|  | *status |= V4L2_IN_ST_NO_SIGNAL; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s: SDP status = 0x%x\n", | 
|  | __func__, *status); | 
|  | return 0; | 
|  | } | 
|  | /* status from CP block */ | 
|  | if ((cp_read(sd, 0xb5) & 0xd0) != 0xd0 || | 
|  | !(cp_read(sd, 0xb1) & 0x80)) | 
|  | /* TODO channel 2 */ | 
|  | *status |= V4L2_IN_ST_NO_SIGNAL; | 
|  |  | 
|  | if (is_digital_input(sd) && ((io_read(sd, 0x74) & 0x03) != 0x03)) | 
|  | *status |= V4L2_IN_ST_NO_SIGNAL; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s: CP status = 0x%x\n", | 
|  | __func__, *status); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | struct stdi_readback { | 
|  | u16 bl, lcf, lcvs; | 
|  | u8 hs_pol, vs_pol; | 
|  | bool interlaced; | 
|  | }; | 
|  |  | 
|  | static int stdi2dv_timings(struct v4l2_subdev *sd, | 
|  | struct stdi_readback *stdi, | 
|  | struct v4l2_dv_timings *timings) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | u32 hfreq = (ADV7842_fsc * 8) / stdi->bl; | 
|  | u32 pix_clk; | 
|  | int i; | 
|  |  | 
|  | for (i = 0; v4l2_dv_timings_presets[i].bt.width; i++) { | 
|  | const struct v4l2_bt_timings *bt = &v4l2_dv_timings_presets[i].bt; | 
|  |  | 
|  | if (!v4l2_valid_dv_timings(&v4l2_dv_timings_presets[i], | 
|  | adv7842_get_dv_timings_cap(sd), | 
|  | adv7842_check_dv_timings, NULL)) | 
|  | continue; | 
|  | if (vtotal(bt) != stdi->lcf + 1) | 
|  | continue; | 
|  | if (bt->vsync != stdi->lcvs) | 
|  | continue; | 
|  |  | 
|  | pix_clk = hfreq * htotal(bt); | 
|  |  | 
|  | if ((pix_clk < bt->pixelclock + 1000000) && | 
|  | (pix_clk > bt->pixelclock - 1000000)) { | 
|  | *timings = v4l2_dv_timings_presets[i]; | 
|  | return 0; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (v4l2_detect_cvt(stdi->lcf + 1, hfreq, stdi->lcvs, 0, | 
|  | (stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) | | 
|  | (stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0), | 
|  | false, adv7842_get_dv_timings_cap(sd), timings)) | 
|  | return 0; | 
|  | if (v4l2_detect_gtf(stdi->lcf + 1, hfreq, stdi->lcvs, | 
|  | (stdi->hs_pol == '+' ? V4L2_DV_HSYNC_POS_POL : 0) | | 
|  | (stdi->vs_pol == '+' ? V4L2_DV_VSYNC_POS_POL : 0), | 
|  | false, state->aspect_ratio, | 
|  | adv7842_get_dv_timings_cap(sd), timings)) | 
|  | return 0; | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, | 
|  | "%s: No format candidate found for lcvs = %d, lcf=%d, bl = %d, %chsync, %cvsync\n", | 
|  | __func__, stdi->lcvs, stdi->lcf, stdi->bl, | 
|  | stdi->hs_pol, stdi->vs_pol); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | static int read_stdi(struct v4l2_subdev *sd, struct stdi_readback *stdi) | 
|  | { | 
|  | u32 status; | 
|  |  | 
|  | adv7842_g_input_status(sd, &status); | 
|  | if (status & V4L2_IN_ST_NO_SIGNAL) { | 
|  | v4l2_dbg(2, debug, sd, "%s: no signal\n", __func__); | 
|  | return -ENOLINK; | 
|  | } | 
|  |  | 
|  | stdi->bl = ((cp_read(sd, 0xb1) & 0x3f) << 8) | cp_read(sd, 0xb2); | 
|  | stdi->lcf = ((cp_read(sd, 0xb3) & 0x7) << 8) | cp_read(sd, 0xb4); | 
|  | stdi->lcvs = cp_read(sd, 0xb3) >> 3; | 
|  |  | 
|  | if ((cp_read(sd, 0xb5) & 0x80) && ((cp_read(sd, 0xb5) & 0x03) == 0x01)) { | 
|  | stdi->hs_pol = ((cp_read(sd, 0xb5) & 0x10) ? | 
|  | ((cp_read(sd, 0xb5) & 0x08) ? '+' : '-') : 'x'); | 
|  | stdi->vs_pol = ((cp_read(sd, 0xb5) & 0x40) ? | 
|  | ((cp_read(sd, 0xb5) & 0x20) ? '+' : '-') : 'x'); | 
|  | } else { | 
|  | stdi->hs_pol = 'x'; | 
|  | stdi->vs_pol = 'x'; | 
|  | } | 
|  | stdi->interlaced = (cp_read(sd, 0xb1) & 0x40) ? true : false; | 
|  |  | 
|  | if (stdi->lcf < 239 || stdi->bl < 8 || stdi->bl == 0x3fff) { | 
|  | v4l2_dbg(2, debug, sd, "%s: invalid signal\n", __func__); | 
|  | return -ENOLINK; | 
|  | } | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, | 
|  | "%s: lcf (frame height - 1) = %d, bl = %d, lcvs (vsync) = %d, %chsync, %cvsync, %s\n", | 
|  | __func__, stdi->lcf, stdi->bl, stdi->lcvs, | 
|  | stdi->hs_pol, stdi->vs_pol, | 
|  | stdi->interlaced ? "interlaced" : "progressive"); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_enum_dv_timings(struct v4l2_subdev *sd, | 
|  | struct v4l2_enum_dv_timings *timings) | 
|  | { | 
|  | if (timings->pad != 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | return v4l2_enum_dv_timings_cap(timings, | 
|  | adv7842_get_dv_timings_cap(sd), adv7842_check_dv_timings, NULL); | 
|  | } | 
|  |  | 
|  | static int adv7842_dv_timings_cap(struct v4l2_subdev *sd, | 
|  | struct v4l2_dv_timings_cap *cap) | 
|  | { | 
|  | if (cap->pad != 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | *cap = *adv7842_get_dv_timings_cap(sd); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* Fill the optional fields .standards and .flags in struct v4l2_dv_timings | 
|  | if the format is listed in adv7842_timings[] */ | 
|  | static void adv7842_fill_optional_dv_timings_fields(struct v4l2_subdev *sd, | 
|  | struct v4l2_dv_timings *timings) | 
|  | { | 
|  | v4l2_find_dv_timings_cap(timings, adv7842_get_dv_timings_cap(sd), | 
|  | is_digital_input(sd) ? 250000 : 1000000, | 
|  | adv7842_check_dv_timings, NULL); | 
|  | timings->bt.flags |= V4L2_DV_FL_CAN_DETECT_REDUCED_FPS; | 
|  | } | 
|  |  | 
|  | static int adv7842_query_dv_timings(struct v4l2_subdev *sd, unsigned int pad, | 
|  | struct v4l2_dv_timings *timings) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct v4l2_bt_timings *bt = &timings->bt; | 
|  | struct stdi_readback stdi = { 0 }; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s:\n", __func__); | 
|  |  | 
|  | if (pad != 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | memset(timings, 0, sizeof(struct v4l2_dv_timings)); | 
|  |  | 
|  | /* SDP block */ | 
|  | if (state->mode == ADV7842_MODE_SDP) | 
|  | return -ENODATA; | 
|  |  | 
|  | /* read STDI */ | 
|  | if (read_stdi(sd, &stdi)) { | 
|  | state->restart_stdi_once = true; | 
|  | v4l2_dbg(1, debug, sd, "%s: no valid signal\n", __func__); | 
|  | return -ENOLINK; | 
|  | } | 
|  | bt->interlaced = stdi.interlaced ? | 
|  | V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE; | 
|  | bt->standards = V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | | 
|  | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT; | 
|  |  | 
|  | if (is_digital_input(sd)) { | 
|  | u32 freq; | 
|  |  | 
|  | timings->type = V4L2_DV_BT_656_1120; | 
|  |  | 
|  | bt->width = (hdmi_read(sd, 0x07) & 0x0f) * 256 + hdmi_read(sd, 0x08); | 
|  | bt->height = (hdmi_read(sd, 0x09) & 0x0f) * 256 + hdmi_read(sd, 0x0a); | 
|  | freq = ((hdmi_read(sd, 0x51) << 1) + (hdmi_read(sd, 0x52) >> 7)) * 1000000; | 
|  | freq += ((hdmi_read(sd, 0x52) & 0x7f) * 7813); | 
|  | if (is_hdmi(sd)) { | 
|  | /* adjust for deep color mode */ | 
|  | freq = freq * 8 / (((hdmi_read(sd, 0x0b) & 0xc0) >> 6) * 2 + 8); | 
|  | } | 
|  | bt->pixelclock = freq; | 
|  | bt->hfrontporch = (hdmi_read(sd, 0x20) & 0x03) * 256 + | 
|  | hdmi_read(sd, 0x21); | 
|  | bt->hsync = (hdmi_read(sd, 0x22) & 0x03) * 256 + | 
|  | hdmi_read(sd, 0x23); | 
|  | bt->hbackporch = (hdmi_read(sd, 0x24) & 0x03) * 256 + | 
|  | hdmi_read(sd, 0x25); | 
|  | bt->vfrontporch = ((hdmi_read(sd, 0x2a) & 0x1f) * 256 + | 
|  | hdmi_read(sd, 0x2b)) / 2; | 
|  | bt->vsync = ((hdmi_read(sd, 0x2e) & 0x1f) * 256 + | 
|  | hdmi_read(sd, 0x2f)) / 2; | 
|  | bt->vbackporch = ((hdmi_read(sd, 0x32) & 0x1f) * 256 + | 
|  | hdmi_read(sd, 0x33)) / 2; | 
|  | bt->polarities = ((hdmi_read(sd, 0x05) & 0x10) ? V4L2_DV_VSYNC_POS_POL : 0) | | 
|  | ((hdmi_read(sd, 0x05) & 0x20) ? V4L2_DV_HSYNC_POS_POL : 0); | 
|  | if (bt->interlaced == V4L2_DV_INTERLACED) { | 
|  | bt->height += (hdmi_read(sd, 0x0b) & 0x0f) * 256 + | 
|  | hdmi_read(sd, 0x0c); | 
|  | bt->il_vfrontporch = ((hdmi_read(sd, 0x2c) & 0x1f) * 256 + | 
|  | hdmi_read(sd, 0x2d)) / 2; | 
|  | bt->il_vsync = ((hdmi_read(sd, 0x30) & 0x1f) * 256 + | 
|  | hdmi_read(sd, 0x31)) / 2; | 
|  | bt->il_vbackporch = ((hdmi_read(sd, 0x34) & 0x1f) * 256 + | 
|  | hdmi_read(sd, 0x35)) / 2; | 
|  | } else { | 
|  | bt->il_vfrontporch = 0; | 
|  | bt->il_vsync = 0; | 
|  | bt->il_vbackporch = 0; | 
|  | } | 
|  | adv7842_fill_optional_dv_timings_fields(sd, timings); | 
|  | if ((timings->bt.flags & V4L2_DV_FL_CAN_REDUCE_FPS) && | 
|  | freq < bt->pixelclock) { | 
|  | u32 reduced_freq = ((u32)bt->pixelclock / 1001) * 1000; | 
|  | u32 delta_freq = abs(freq - reduced_freq); | 
|  |  | 
|  | if (delta_freq < ((u32)bt->pixelclock - reduced_freq) / 2) | 
|  | timings->bt.flags |= V4L2_DV_FL_REDUCED_FPS; | 
|  | } | 
|  | } else { | 
|  | /* find format | 
|  | * Since LCVS values are inaccurate [REF_03, p. 339-340], | 
|  | * stdi2dv_timings() is called with lcvs +-1 if the first attempt fails. | 
|  | */ | 
|  | if (!stdi2dv_timings(sd, &stdi, timings)) | 
|  | goto found; | 
|  | stdi.lcvs += 1; | 
|  | v4l2_dbg(1, debug, sd, "%s: lcvs + 1 = %d\n", __func__, stdi.lcvs); | 
|  | if (!stdi2dv_timings(sd, &stdi, timings)) | 
|  | goto found; | 
|  | stdi.lcvs -= 2; | 
|  | v4l2_dbg(1, debug, sd, "%s: lcvs - 1 = %d\n", __func__, stdi.lcvs); | 
|  | if (stdi2dv_timings(sd, &stdi, timings)) { | 
|  | /* | 
|  | * The STDI block may measure wrong values, especially | 
|  | * for lcvs and lcf. If the driver can not find any | 
|  | * valid timing, the STDI block is restarted to measure | 
|  | * the video timings again. The function will return an | 
|  | * error, but the restart of STDI will generate a new | 
|  | * STDI interrupt and the format detection process will | 
|  | * restart. | 
|  | */ | 
|  | if (state->restart_stdi_once) { | 
|  | v4l2_dbg(1, debug, sd, "%s: restart STDI\n", __func__); | 
|  | /* TODO restart STDI for Sync Channel 2 */ | 
|  | /* enter one-shot mode */ | 
|  | cp_write_and_or(sd, 0x86, 0xf9, 0x00); | 
|  | /* trigger STDI restart */ | 
|  | cp_write_and_or(sd, 0x86, 0xf9, 0x04); | 
|  | /* reset to continuous mode */ | 
|  | cp_write_and_or(sd, 0x86, 0xf9, 0x02); | 
|  | state->restart_stdi_once = false; | 
|  | return -ENOLINK; | 
|  | } | 
|  | v4l2_dbg(1, debug, sd, "%s: format not supported\n", __func__); | 
|  | return -ERANGE; | 
|  | } | 
|  | state->restart_stdi_once = true; | 
|  | } | 
|  | found: | 
|  |  | 
|  | if (debug > 1) | 
|  | v4l2_print_dv_timings(sd->name, "adv7842_query_dv_timings:", | 
|  | timings, true); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_s_dv_timings(struct v4l2_subdev *sd, unsigned int pad, | 
|  | struct v4l2_dv_timings *timings) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct v4l2_bt_timings *bt; | 
|  | int err; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s:\n", __func__); | 
|  |  | 
|  | if (pad != 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_SDP) | 
|  | return -ENODATA; | 
|  |  | 
|  | if (v4l2_match_dv_timings(&state->timings, timings, 0, false)) { | 
|  | v4l2_dbg(1, debug, sd, "%s: no change\n", __func__); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | bt = &timings->bt; | 
|  |  | 
|  | if (!v4l2_valid_dv_timings(timings, adv7842_get_dv_timings_cap(sd), | 
|  | adv7842_check_dv_timings, NULL)) | 
|  | return -ERANGE; | 
|  |  | 
|  | adv7842_fill_optional_dv_timings_fields(sd, timings); | 
|  |  | 
|  | state->timings = *timings; | 
|  |  | 
|  | cp_write(sd, 0x91, bt->interlaced ? 0x40 : 0x00); | 
|  |  | 
|  | /* Use prim_mode and vid_std when available */ | 
|  | err = configure_predefined_video_timings(sd, timings); | 
|  | if (err) { | 
|  | /* custom settings when the video format | 
|  | does not have prim_mode/vid_std */ | 
|  | configure_custom_video_timings(sd, bt); | 
|  | } | 
|  |  | 
|  | set_rgb_quantization_range(sd); | 
|  |  | 
|  |  | 
|  | if (debug > 1) | 
|  | v4l2_print_dv_timings(sd->name, "adv7842_s_dv_timings: ", | 
|  | timings, true); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_g_dv_timings(struct v4l2_subdev *sd, unsigned int pad, | 
|  | struct v4l2_dv_timings *timings) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | if (pad != 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_SDP) | 
|  | return -ENODATA; | 
|  | *timings = state->timings; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void enable_input(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | set_rgb_quantization_range(sd); | 
|  | switch (state->mode) { | 
|  | case ADV7842_MODE_SDP: | 
|  | case ADV7842_MODE_COMP: | 
|  | case ADV7842_MODE_RGB: | 
|  | io_write(sd, 0x15, 0xb0);   /* Disable Tristate of Pins (no audio) */ | 
|  | break; | 
|  | case ADV7842_MODE_HDMI: | 
|  | hdmi_write(sd, 0x01, 0x00); /* Enable HDMI clock terminators */ | 
|  | io_write(sd, 0x15, 0xa0);   /* Disable Tristate of Pins */ | 
|  | hdmi_write_and_or(sd, 0x1a, 0xef, 0x00); /* Unmute audio */ | 
|  | break; | 
|  | default: | 
|  | v4l2_dbg(2, debug, sd, "%s: Unknown mode %d\n", | 
|  | __func__, state->mode); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | static void disable_input(struct v4l2_subdev *sd) | 
|  | { | 
|  | hdmi_write_and_or(sd, 0x1a, 0xef, 0x10); /* Mute audio [REF_01, c. 2.2.2] */ | 
|  | msleep(16); /* 512 samples with >= 32 kHz sample rate [REF_03, c. 8.29] */ | 
|  | io_write(sd, 0x15, 0xbe);   /* Tristate all outputs from video core */ | 
|  | hdmi_write(sd, 0x01, 0x78); /* Disable HDMI clock terminators */ | 
|  | } | 
|  |  | 
|  | static void sdp_csc_coeff(struct v4l2_subdev *sd, | 
|  | const struct adv7842_sdp_csc_coeff *c) | 
|  | { | 
|  | /* csc auto/manual */ | 
|  | sdp_io_write_and_or(sd, 0xe0, 0xbf, c->manual ? 0x00 : 0x40); | 
|  |  | 
|  | if (!c->manual) | 
|  | return; | 
|  |  | 
|  | /* csc scaling */ | 
|  | sdp_io_write_and_or(sd, 0xe0, 0x7f, c->scaling == 2 ? 0x80 : 0x00); | 
|  |  | 
|  | /* A coeff */ | 
|  | sdp_io_write_and_or(sd, 0xe0, 0xe0, c->A1 >> 8); | 
|  | sdp_io_write(sd, 0xe1, c->A1); | 
|  | sdp_io_write_and_or(sd, 0xe2, 0xe0, c->A2 >> 8); | 
|  | sdp_io_write(sd, 0xe3, c->A2); | 
|  | sdp_io_write_and_or(sd, 0xe4, 0xe0, c->A3 >> 8); | 
|  | sdp_io_write(sd, 0xe5, c->A3); | 
|  |  | 
|  | /* A scale */ | 
|  | sdp_io_write_and_or(sd, 0xe6, 0x80, c->A4 >> 8); | 
|  | sdp_io_write(sd, 0xe7, c->A4); | 
|  |  | 
|  | /* B coeff */ | 
|  | sdp_io_write_and_or(sd, 0xe8, 0xe0, c->B1 >> 8); | 
|  | sdp_io_write(sd, 0xe9, c->B1); | 
|  | sdp_io_write_and_or(sd, 0xea, 0xe0, c->B2 >> 8); | 
|  | sdp_io_write(sd, 0xeb, c->B2); | 
|  | sdp_io_write_and_or(sd, 0xec, 0xe0, c->B3 >> 8); | 
|  | sdp_io_write(sd, 0xed, c->B3); | 
|  |  | 
|  | /* B scale */ | 
|  | sdp_io_write_and_or(sd, 0xee, 0x80, c->B4 >> 8); | 
|  | sdp_io_write(sd, 0xef, c->B4); | 
|  |  | 
|  | /* C coeff */ | 
|  | sdp_io_write_and_or(sd, 0xf0, 0xe0, c->C1 >> 8); | 
|  | sdp_io_write(sd, 0xf1, c->C1); | 
|  | sdp_io_write_and_or(sd, 0xf2, 0xe0, c->C2 >> 8); | 
|  | sdp_io_write(sd, 0xf3, c->C2); | 
|  | sdp_io_write_and_or(sd, 0xf4, 0xe0, c->C3 >> 8); | 
|  | sdp_io_write(sd, 0xf5, c->C3); | 
|  |  | 
|  | /* C scale */ | 
|  | sdp_io_write_and_or(sd, 0xf6, 0x80, c->C4 >> 8); | 
|  | sdp_io_write(sd, 0xf7, c->C4); | 
|  | } | 
|  |  | 
|  | static void select_input(struct v4l2_subdev *sd, | 
|  | enum adv7842_vid_std_select vid_std_select) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | switch (state->mode) { | 
|  | case ADV7842_MODE_SDP: | 
|  | io_write(sd, 0x00, vid_std_select); /* video std: CVBS or YC mode */ | 
|  | io_write(sd, 0x01, 0); /* prim mode */ | 
|  | /* enable embedded syncs for auto graphics mode */ | 
|  | cp_write_and_or(sd, 0x81, 0xef, 0x10); | 
|  |  | 
|  | afe_write(sd, 0x00, 0x00); /* power up ADC */ | 
|  | afe_write(sd, 0xc8, 0x00); /* phase control */ | 
|  |  | 
|  | io_write(sd, 0xdd, 0x90); /* Manual 2x output clock */ | 
|  | /* script says register 0xde, which don't exist in manual */ | 
|  |  | 
|  | /* Manual analog input muxing mode, CVBS (6.4)*/ | 
|  | afe_write_and_or(sd, 0x02, 0x7f, 0x80); | 
|  | if (vid_std_select == ADV7842_SDP_VID_STD_CVBS_SD_4x1) { | 
|  | afe_write(sd, 0x03, 0xa0); /* ADC0 to AIN10 (CVBS), ADC1 N/C*/ | 
|  | afe_write(sd, 0x04, 0x00); /* ADC2 N/C,ADC3 N/C*/ | 
|  | } else { | 
|  | afe_write(sd, 0x03, 0xa0); /* ADC0 to AIN10 (CVBS), ADC1 N/C*/ | 
|  | afe_write(sd, 0x04, 0xc0); /* ADC2 to AIN12, ADC3 N/C*/ | 
|  | } | 
|  | afe_write(sd, 0x0c, 0x1f); /* ADI recommend write */ | 
|  | afe_write(sd, 0x12, 0x63); /* ADI recommend write */ | 
|  |  | 
|  | sdp_io_write(sd, 0xb2, 0x60); /* Disable AV codes */ | 
|  | sdp_io_write(sd, 0xc8, 0xe3); /* Disable Ancillary data */ | 
|  |  | 
|  | /* SDP recommended settings */ | 
|  | sdp_write(sd, 0x00, 0x3F); /* Autodetect PAL NTSC (not SECAM) */ | 
|  | sdp_write(sd, 0x01, 0x00); /* Pedestal Off */ | 
|  |  | 
|  | sdp_write(sd, 0x03, 0xE4); /* Manual VCR Gain Luma 0x40B */ | 
|  | sdp_write(sd, 0x04, 0x0B); /* Manual Luma setting */ | 
|  | sdp_write(sd, 0x05, 0xC3); /* Manual Chroma setting 0x3FE */ | 
|  | sdp_write(sd, 0x06, 0xFE); /* Manual Chroma setting */ | 
|  | sdp_write(sd, 0x12, 0x0D); /* Frame TBC,I_P, 3D comb enabled */ | 
|  | sdp_write(sd, 0xA7, 0x00); /* ADI Recommended Write */ | 
|  | sdp_io_write(sd, 0xB0, 0x00); /* Disable H and v blanking */ | 
|  |  | 
|  | /* deinterlacer enabled and 3D comb */ | 
|  | sdp_write_and_or(sd, 0x12, 0xf6, 0x09); | 
|  |  | 
|  | break; | 
|  |  | 
|  | case ADV7842_MODE_COMP: | 
|  | case ADV7842_MODE_RGB: | 
|  | /* Automatic analog input muxing mode */ | 
|  | afe_write_and_or(sd, 0x02, 0x7f, 0x00); | 
|  | /* set mode and select free run resolution */ | 
|  | io_write(sd, 0x00, vid_std_select); /* video std */ | 
|  | io_write(sd, 0x01, 0x02); /* prim mode */ | 
|  | cp_write_and_or(sd, 0x81, 0xef, 0x10); /* enable embedded syncs | 
|  | for auto graphics mode */ | 
|  |  | 
|  | afe_write(sd, 0x00, 0x00); /* power up ADC */ | 
|  | afe_write(sd, 0xc8, 0x00); /* phase control */ | 
|  | if (state->mode == ADV7842_MODE_COMP) { | 
|  | /* force to YCrCb */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x60); | 
|  | } else { | 
|  | /* force to RGB */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0x10); | 
|  | } | 
|  |  | 
|  | /* set ADI recommended settings for digitizer */ | 
|  | /* "ADV7842 Register Settings Recommendations | 
|  | * (rev. 1.8, November 2010)" p. 9. */ | 
|  | afe_write(sd, 0x0c, 0x1f); /* ADC Range improvement */ | 
|  | afe_write(sd, 0x12, 0x63); /* ADC Range improvement */ | 
|  |  | 
|  | /* set to default gain for RGB */ | 
|  | cp_write(sd, 0x73, 0x10); | 
|  | cp_write(sd, 0x74, 0x04); | 
|  | cp_write(sd, 0x75, 0x01); | 
|  | cp_write(sd, 0x76, 0x00); | 
|  |  | 
|  | cp_write(sd, 0x3e, 0x04); /* CP core pre-gain control */ | 
|  | cp_write(sd, 0xc3, 0x39); /* CP coast control. Graphics mode */ | 
|  | cp_write(sd, 0x40, 0x5c); /* CP core pre-gain control. Graphics mode */ | 
|  | break; | 
|  |  | 
|  | case ADV7842_MODE_HDMI: | 
|  | /* Automatic analog input muxing mode */ | 
|  | afe_write_and_or(sd, 0x02, 0x7f, 0x00); | 
|  | /* set mode and select free run resolution */ | 
|  | if (state->hdmi_port_a) | 
|  | hdmi_write(sd, 0x00, 0x02); /* select port A */ | 
|  | else | 
|  | hdmi_write(sd, 0x00, 0x03); /* select port B */ | 
|  | io_write(sd, 0x00, vid_std_select); /* video std */ | 
|  | io_write(sd, 0x01, 5); /* prim mode */ | 
|  | cp_write_and_or(sd, 0x81, 0xef, 0x00); /* disable embedded syncs | 
|  | for auto graphics mode */ | 
|  |  | 
|  | /* set ADI recommended settings for HDMI: */ | 
|  | /* "ADV7842 Register Settings Recommendations | 
|  | * (rev. 1.8, November 2010)" p. 3. */ | 
|  | hdmi_write(sd, 0xc0, 0x00); | 
|  | hdmi_write(sd, 0x0d, 0x34); /* ADI recommended write */ | 
|  | hdmi_write(sd, 0x3d, 0x10); /* ADI recommended write */ | 
|  | hdmi_write(sd, 0x44, 0x85); /* TMDS PLL optimization */ | 
|  | hdmi_write(sd, 0x46, 0x1f); /* ADI recommended write */ | 
|  | hdmi_write(sd, 0x57, 0xb6); /* TMDS PLL optimization */ | 
|  | hdmi_write(sd, 0x58, 0x03); /* TMDS PLL optimization */ | 
|  | hdmi_write(sd, 0x60, 0x88); /* TMDS PLL optimization */ | 
|  | hdmi_write(sd, 0x61, 0x88); /* TMDS PLL optimization */ | 
|  | hdmi_write(sd, 0x6c, 0x18); /* Disable ISRC clearing bit, | 
|  | Improve robustness */ | 
|  | hdmi_write(sd, 0x75, 0x10); /* DDC drive strength */ | 
|  | hdmi_write(sd, 0x85, 0x1f); /* equaliser */ | 
|  | hdmi_write(sd, 0x87, 0x70); /* ADI recommended write */ | 
|  | hdmi_write(sd, 0x89, 0x04); /* equaliser */ | 
|  | hdmi_write(sd, 0x8a, 0x1e); /* equaliser */ | 
|  | hdmi_write(sd, 0x93, 0x04); /* equaliser */ | 
|  | hdmi_write(sd, 0x94, 0x1e); /* equaliser */ | 
|  | hdmi_write(sd, 0x99, 0xa1); /* ADI recommended write */ | 
|  | hdmi_write(sd, 0x9b, 0x09); /* ADI recommended write */ | 
|  | hdmi_write(sd, 0x9d, 0x02); /* equaliser */ | 
|  |  | 
|  | afe_write(sd, 0x00, 0xff); /* power down ADC */ | 
|  | afe_write(sd, 0xc8, 0x40); /* phase control */ | 
|  |  | 
|  | /* set to default gain for HDMI */ | 
|  | cp_write(sd, 0x73, 0x10); | 
|  | cp_write(sd, 0x74, 0x04); | 
|  | cp_write(sd, 0x75, 0x01); | 
|  | cp_write(sd, 0x76, 0x00); | 
|  |  | 
|  | /* reset ADI recommended settings for digitizer */ | 
|  | /* "ADV7842 Register Settings Recommendations | 
|  | * (rev. 2.5, June 2010)" p. 17. */ | 
|  | afe_write(sd, 0x12, 0xfb); /* ADC noise shaping filter controls */ | 
|  | afe_write(sd, 0x0c, 0x0d); /* CP core gain controls */ | 
|  | cp_write(sd, 0x3e, 0x00); /* CP core pre-gain control */ | 
|  |  | 
|  | /* CP coast control */ | 
|  | cp_write(sd, 0xc3, 0x33); /* Component mode */ | 
|  |  | 
|  | /* color space conversion, autodetect color space */ | 
|  | io_write_and_or(sd, 0x02, 0x0f, 0xf0); | 
|  | break; | 
|  |  | 
|  | default: | 
|  | v4l2_dbg(2, debug, sd, "%s: Unknown mode %d\n", | 
|  | __func__, state->mode); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int adv7842_s_routing(struct v4l2_subdev *sd, | 
|  | u32 input, u32 output, u32 config) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | v4l2_dbg(2, debug, sd, "%s: input %d\n", __func__, input); | 
|  |  | 
|  | switch (input) { | 
|  | case ADV7842_SELECT_HDMI_PORT_A: | 
|  | state->mode = ADV7842_MODE_HDMI; | 
|  | state->vid_std_select = ADV7842_HDMI_COMP_VID_STD_HD_1250P; | 
|  | state->hdmi_port_a = true; | 
|  | break; | 
|  | case ADV7842_SELECT_HDMI_PORT_B: | 
|  | state->mode = ADV7842_MODE_HDMI; | 
|  | state->vid_std_select = ADV7842_HDMI_COMP_VID_STD_HD_1250P; | 
|  | state->hdmi_port_a = false; | 
|  | break; | 
|  | case ADV7842_SELECT_VGA_COMP: | 
|  | state->mode = ADV7842_MODE_COMP; | 
|  | state->vid_std_select = ADV7842_RGB_VID_STD_AUTO_GRAPH_MODE; | 
|  | break; | 
|  | case ADV7842_SELECT_VGA_RGB: | 
|  | state->mode = ADV7842_MODE_RGB; | 
|  | state->vid_std_select = ADV7842_RGB_VID_STD_AUTO_GRAPH_MODE; | 
|  | break; | 
|  | case ADV7842_SELECT_SDP_CVBS: | 
|  | state->mode = ADV7842_MODE_SDP; | 
|  | state->vid_std_select = ADV7842_SDP_VID_STD_CVBS_SD_4x1; | 
|  | break; | 
|  | case ADV7842_SELECT_SDP_YC: | 
|  | state->mode = ADV7842_MODE_SDP; | 
|  | state->vid_std_select = ADV7842_SDP_VID_STD_YC_SD4_x1; | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | disable_input(sd); | 
|  | select_input(sd, state->vid_std_select); | 
|  | enable_input(sd); | 
|  |  | 
|  | v4l2_subdev_notify_event(sd, &adv7842_ev_fmt); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_enum_mbus_code(struct v4l2_subdev *sd, | 
|  | struct v4l2_subdev_state *sd_state, | 
|  | struct v4l2_subdev_mbus_code_enum *code) | 
|  | { | 
|  | if (code->index >= ARRAY_SIZE(adv7842_formats)) | 
|  | return -EINVAL; | 
|  | code->code = adv7842_formats[code->index].code; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void adv7842_fill_format(struct adv7842_state *state, | 
|  | struct v4l2_mbus_framefmt *format) | 
|  | { | 
|  | memset(format, 0, sizeof(*format)); | 
|  |  | 
|  | format->width = state->timings.bt.width; | 
|  | format->height = state->timings.bt.height; | 
|  | format->field = V4L2_FIELD_NONE; | 
|  | format->colorspace = V4L2_COLORSPACE_SRGB; | 
|  |  | 
|  | if (state->timings.bt.flags & V4L2_DV_FL_IS_CE_VIDEO) | 
|  | format->colorspace = (state->timings.bt.height <= 576) ? | 
|  | V4L2_COLORSPACE_SMPTE170M : V4L2_COLORSPACE_REC709; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Compute the op_ch_sel value required to obtain on the bus the component order | 
|  | * corresponding to the selected format taking into account bus reordering | 
|  | * applied by the board at the output of the device. | 
|  | * | 
|  | * The following table gives the op_ch_value from the format component order | 
|  | * (expressed as op_ch_sel value in column) and the bus reordering (expressed as | 
|  | * adv7842_bus_order value in row). | 
|  | * | 
|  | *           |	GBR(0)	GRB(1)	BGR(2)	RGB(3)	BRG(4)	RBG(5) | 
|  | * ----------+------------------------------------------------- | 
|  | * RGB (NOP) |	GBR	GRB	BGR	RGB	BRG	RBG | 
|  | * GRB (1-2) |	BGR	RGB	GBR	GRB	RBG	BRG | 
|  | * RBG (2-3) |	GRB	GBR	BRG	RBG	BGR	RGB | 
|  | * BGR (1-3) |	RBG	BRG	RGB	BGR	GRB	GBR | 
|  | * BRG (ROR) |	BRG	RBG	GRB	GBR	RGB	BGR | 
|  | * GBR (ROL) |	RGB	BGR	RBG	BRG	GBR	GRB | 
|  | */ | 
|  | static unsigned int adv7842_op_ch_sel(struct adv7842_state *state) | 
|  | { | 
|  | #define _SEL(a, b, c, d, e, f)	{ \ | 
|  | ADV7842_OP_CH_SEL_##a, ADV7842_OP_CH_SEL_##b, ADV7842_OP_CH_SEL_##c, \ | 
|  | ADV7842_OP_CH_SEL_##d, ADV7842_OP_CH_SEL_##e, ADV7842_OP_CH_SEL_##f } | 
|  | #define _BUS(x)			[ADV7842_BUS_ORDER_##x] | 
|  |  | 
|  | static const unsigned int op_ch_sel[6][6] = { | 
|  | _BUS(RGB) /* NOP */ = _SEL(GBR, GRB, BGR, RGB, BRG, RBG), | 
|  | _BUS(GRB) /* 1-2 */ = _SEL(BGR, RGB, GBR, GRB, RBG, BRG), | 
|  | _BUS(RBG) /* 2-3 */ = _SEL(GRB, GBR, BRG, RBG, BGR, RGB), | 
|  | _BUS(BGR) /* 1-3 */ = _SEL(RBG, BRG, RGB, BGR, GRB, GBR), | 
|  | _BUS(BRG) /* ROR */ = _SEL(BRG, RBG, GRB, GBR, RGB, BGR), | 
|  | _BUS(GBR) /* ROL */ = _SEL(RGB, BGR, RBG, BRG, GBR, GRB), | 
|  | }; | 
|  |  | 
|  | return op_ch_sel[state->pdata.bus_order][state->format->op_ch_sel >> 5]; | 
|  | } | 
|  |  | 
|  | static void adv7842_setup_format(struct adv7842_state *state) | 
|  | { | 
|  | struct v4l2_subdev *sd = &state->sd; | 
|  |  | 
|  | io_write_clr_set(sd, 0x02, 0x02, | 
|  | state->format->rgb_out ? ADV7842_RGB_OUT : 0); | 
|  | io_write(sd, 0x03, state->format->op_format_sel | | 
|  | state->pdata.op_format_mode_sel); | 
|  | io_write_clr_set(sd, 0x04, 0xe0, adv7842_op_ch_sel(state)); | 
|  | io_write_clr_set(sd, 0x05, 0x01, | 
|  | state->format->swap_cb_cr ? ADV7842_OP_SWAP_CB_CR : 0); | 
|  | set_rgb_quantization_range(sd); | 
|  | } | 
|  |  | 
|  | static int adv7842_get_format(struct v4l2_subdev *sd, | 
|  | struct v4l2_subdev_state *sd_state, | 
|  | struct v4l2_subdev_format *format) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | if (format->pad != ADV7842_PAD_SOURCE) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_SDP) { | 
|  | /* SPD block */ | 
|  | if (!(sdp_read(sd, 0x5a) & 0x01)) | 
|  | return -EINVAL; | 
|  | format->format.code = MEDIA_BUS_FMT_YUYV8_2X8; | 
|  | format->format.width = 720; | 
|  | /* valid signal */ | 
|  | if (state->norm & V4L2_STD_525_60) | 
|  | format->format.height = 480; | 
|  | else | 
|  | format->format.height = 576; | 
|  | format->format.colorspace = V4L2_COLORSPACE_SMPTE170M; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | adv7842_fill_format(state, &format->format); | 
|  |  | 
|  | if (format->which == V4L2_SUBDEV_FORMAT_TRY) { | 
|  | struct v4l2_mbus_framefmt *fmt; | 
|  |  | 
|  | fmt = v4l2_subdev_state_get_format(sd_state, format->pad); | 
|  | format->format.code = fmt->code; | 
|  | } else { | 
|  | format->format.code = state->format->code; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_set_format(struct v4l2_subdev *sd, | 
|  | struct v4l2_subdev_state *sd_state, | 
|  | struct v4l2_subdev_format *format) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | const struct adv7842_format_info *info; | 
|  |  | 
|  | if (format->pad != ADV7842_PAD_SOURCE) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_SDP) | 
|  | return adv7842_get_format(sd, sd_state, format); | 
|  |  | 
|  | info = adv7842_format_info(state, format->format.code); | 
|  | if (info == NULL) | 
|  | info = adv7842_format_info(state, MEDIA_BUS_FMT_YUYV8_2X8); | 
|  |  | 
|  | adv7842_fill_format(state, &format->format); | 
|  | format->format.code = info->code; | 
|  |  | 
|  | if (format->which == V4L2_SUBDEV_FORMAT_TRY) { | 
|  | struct v4l2_mbus_framefmt *fmt; | 
|  |  | 
|  | fmt = v4l2_subdev_state_get_format(sd_state, format->pad); | 
|  | fmt->code = format->format.code; | 
|  | } else { | 
|  | state->format = info; | 
|  | adv7842_setup_format(state); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void adv7842_irq_enable(struct v4l2_subdev *sd, bool enable) | 
|  | { | 
|  | if (enable) { | 
|  | /* Enable SSPD, STDI and CP locked/unlocked interrupts */ | 
|  | io_write(sd, 0x46, 0x9c); | 
|  | /* ESDP_50HZ_DET interrupt */ | 
|  | io_write(sd, 0x5a, 0x10); | 
|  | /* Enable CABLE_DET_A/B_ST (+5v) interrupt */ | 
|  | io_write(sd, 0x73, 0x03); | 
|  | /* Enable V_LOCKED and DE_REGEN_LCK interrupts */ | 
|  | io_write(sd, 0x78, 0x03); | 
|  | /* Enable SDP Standard Detection Change and SDP Video Detected */ | 
|  | io_write(sd, 0xa0, 0x09); | 
|  | /* Enable HDMI_MODE interrupt */ | 
|  | io_write(sd, 0x69, 0x08); | 
|  | } else { | 
|  | io_write(sd, 0x46, 0x0); | 
|  | io_write(sd, 0x5a, 0x0); | 
|  | io_write(sd, 0x73, 0x0); | 
|  | io_write(sd, 0x78, 0x0); | 
|  | io_write(sd, 0xa0, 0x0); | 
|  | io_write(sd, 0x69, 0x0); | 
|  | } | 
|  | } | 
|  |  | 
|  | #if IS_ENABLED(CONFIG_VIDEO_ADV7842_CEC) | 
|  | static void adv7842_cec_tx_raw_status(struct v4l2_subdev *sd, u8 tx_raw_status) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | if ((cec_read(sd, 0x11) & 0x01) == 0) { | 
|  | v4l2_dbg(1, debug, sd, "%s: tx raw: tx disabled\n", __func__); | 
|  | return; | 
|  | } | 
|  |  | 
|  | if (tx_raw_status & 0x02) { | 
|  | v4l2_dbg(1, debug, sd, "%s: tx raw: arbitration lost\n", | 
|  | __func__); | 
|  | cec_transmit_done(state->cec_adap, CEC_TX_STATUS_ARB_LOST, | 
|  | 1, 0, 0, 0); | 
|  | return; | 
|  | } | 
|  | if (tx_raw_status & 0x04) { | 
|  | u8 status; | 
|  | u8 nack_cnt; | 
|  | u8 low_drive_cnt; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s: tx raw: retry failed\n", __func__); | 
|  | /* | 
|  | * We set this status bit since this hardware performs | 
|  | * retransmissions. | 
|  | */ | 
|  | status = CEC_TX_STATUS_MAX_RETRIES; | 
|  | nack_cnt = cec_read(sd, 0x14) & 0xf; | 
|  | if (nack_cnt) | 
|  | status |= CEC_TX_STATUS_NACK; | 
|  | low_drive_cnt = cec_read(sd, 0x14) >> 4; | 
|  | if (low_drive_cnt) | 
|  | status |= CEC_TX_STATUS_LOW_DRIVE; | 
|  | cec_transmit_done(state->cec_adap, status, | 
|  | 0, nack_cnt, low_drive_cnt, 0); | 
|  | return; | 
|  | } | 
|  | if (tx_raw_status & 0x01) { | 
|  | v4l2_dbg(1, debug, sd, "%s: tx raw: ready ok\n", __func__); | 
|  | cec_transmit_done(state->cec_adap, CEC_TX_STATUS_OK, 0, 0, 0, 0); | 
|  | return; | 
|  | } | 
|  | } | 
|  |  | 
|  | static void adv7842_cec_isr(struct v4l2_subdev *sd, bool *handled) | 
|  | { | 
|  | u8 cec_irq; | 
|  |  | 
|  | /* cec controller */ | 
|  | cec_irq = io_read(sd, 0x93) & 0x0f; | 
|  | if (!cec_irq) | 
|  | return; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s: cec: irq 0x%x\n", __func__, cec_irq); | 
|  | adv7842_cec_tx_raw_status(sd, cec_irq); | 
|  | if (cec_irq & 0x08) { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct cec_msg msg; | 
|  |  | 
|  | msg.len = cec_read(sd, 0x25) & 0x1f; | 
|  | if (msg.len > CEC_MAX_MSG_SIZE) | 
|  | msg.len = CEC_MAX_MSG_SIZE; | 
|  |  | 
|  | if (msg.len) { | 
|  | u8 i; | 
|  |  | 
|  | for (i = 0; i < msg.len; i++) | 
|  | msg.msg[i] = cec_read(sd, i + 0x15); | 
|  | cec_write(sd, 0x26, 0x01); /* re-enable rx */ | 
|  | cec_received_msg(state->cec_adap, &msg); | 
|  | } | 
|  | } | 
|  |  | 
|  | io_write(sd, 0x94, cec_irq); | 
|  |  | 
|  | if (handled) | 
|  | *handled = true; | 
|  | } | 
|  |  | 
|  | static int adv7842_cec_adap_enable(struct cec_adapter *adap, bool enable) | 
|  | { | 
|  | struct adv7842_state *state = cec_get_drvdata(adap); | 
|  | struct v4l2_subdev *sd = &state->sd; | 
|  |  | 
|  | if (!state->cec_enabled_adap && enable) { | 
|  | cec_write_clr_set(sd, 0x2a, 0x01, 0x01); /* power up cec */ | 
|  | cec_write(sd, 0x2c, 0x01);	/* cec soft reset */ | 
|  | cec_write_clr_set(sd, 0x11, 0x01, 0); /* initially disable tx */ | 
|  | /* enabled irqs: */ | 
|  | /* tx: ready */ | 
|  | /* tx: arbitration lost */ | 
|  | /* tx: retry timeout */ | 
|  | /* rx: ready */ | 
|  | io_write_clr_set(sd, 0x96, 0x0f, 0x0f); | 
|  | cec_write(sd, 0x26, 0x01);            /* enable rx */ | 
|  | } else if (state->cec_enabled_adap && !enable) { | 
|  | /* disable cec interrupts */ | 
|  | io_write_clr_set(sd, 0x96, 0x0f, 0x00); | 
|  | /* disable address mask 1-3 */ | 
|  | cec_write_clr_set(sd, 0x27, 0x70, 0x00); | 
|  | /* power down cec section */ | 
|  | cec_write_clr_set(sd, 0x2a, 0x01, 0x00); | 
|  | state->cec_valid_addrs = 0; | 
|  | } | 
|  | state->cec_enabled_adap = enable; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_cec_adap_log_addr(struct cec_adapter *adap, u8 addr) | 
|  | { | 
|  | struct adv7842_state *state = cec_get_drvdata(adap); | 
|  | struct v4l2_subdev *sd = &state->sd; | 
|  | unsigned int i, free_idx = ADV7842_MAX_ADDRS; | 
|  |  | 
|  | if (!state->cec_enabled_adap) | 
|  | return addr == CEC_LOG_ADDR_INVALID ? 0 : -EIO; | 
|  |  | 
|  | if (addr == CEC_LOG_ADDR_INVALID) { | 
|  | cec_write_clr_set(sd, 0x27, 0x70, 0); | 
|  | state->cec_valid_addrs = 0; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < ADV7842_MAX_ADDRS; i++) { | 
|  | bool is_valid = state->cec_valid_addrs & (1 << i); | 
|  |  | 
|  | if (free_idx == ADV7842_MAX_ADDRS && !is_valid) | 
|  | free_idx = i; | 
|  | if (is_valid && state->cec_addr[i] == addr) | 
|  | return 0; | 
|  | } | 
|  | if (i == ADV7842_MAX_ADDRS) { | 
|  | i = free_idx; | 
|  | if (i == ADV7842_MAX_ADDRS) | 
|  | return -ENXIO; | 
|  | } | 
|  | state->cec_addr[i] = addr; | 
|  | state->cec_valid_addrs |= 1 << i; | 
|  |  | 
|  | switch (i) { | 
|  | case 0: | 
|  | /* enable address mask 0 */ | 
|  | cec_write_clr_set(sd, 0x27, 0x10, 0x10); | 
|  | /* set address for mask 0 */ | 
|  | cec_write_clr_set(sd, 0x28, 0x0f, addr); | 
|  | break; | 
|  | case 1: | 
|  | /* enable address mask 1 */ | 
|  | cec_write_clr_set(sd, 0x27, 0x20, 0x20); | 
|  | /* set address for mask 1 */ | 
|  | cec_write_clr_set(sd, 0x28, 0xf0, addr << 4); | 
|  | break; | 
|  | case 2: | 
|  | /* enable address mask 2 */ | 
|  | cec_write_clr_set(sd, 0x27, 0x40, 0x40); | 
|  | /* set address for mask 1 */ | 
|  | cec_write_clr_set(sd, 0x29, 0x0f, addr); | 
|  | break; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_cec_adap_transmit(struct cec_adapter *adap, u8 attempts, | 
|  | u32 signal_free_time, struct cec_msg *msg) | 
|  | { | 
|  | struct adv7842_state *state = cec_get_drvdata(adap); | 
|  | struct v4l2_subdev *sd = &state->sd; | 
|  | u8 len = msg->len; | 
|  | unsigned int i; | 
|  |  | 
|  | /* | 
|  | * The number of retries is the number of attempts - 1, but retry | 
|  | * at least once. It's not clear if a value of 0 is allowed, so | 
|  | * let's do at least one retry. | 
|  | */ | 
|  | cec_write_clr_set(sd, 0x12, 0x70, max(1, attempts - 1) << 4); | 
|  |  | 
|  | if (len > 16) { | 
|  | v4l2_err(sd, "%s: len exceeded 16 (%d)\n", __func__, len); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | /* write data */ | 
|  | for (i = 0; i < len; i++) | 
|  | cec_write(sd, i, msg->msg[i]); | 
|  |  | 
|  | /* set length (data + header) */ | 
|  | cec_write(sd, 0x10, len); | 
|  | /* start transmit, enable tx */ | 
|  | cec_write(sd, 0x11, 0x01); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct cec_adap_ops adv7842_cec_adap_ops = { | 
|  | .adap_enable = adv7842_cec_adap_enable, | 
|  | .adap_log_addr = adv7842_cec_adap_log_addr, | 
|  | .adap_transmit = adv7842_cec_adap_transmit, | 
|  | }; | 
|  | #endif | 
|  |  | 
|  | static int adv7842_isr(struct v4l2_subdev *sd, u32 status, bool *handled) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | u8 fmt_change_cp, fmt_change_digital, fmt_change_sdp; | 
|  | u8 irq_status[6]; | 
|  |  | 
|  | adv7842_irq_enable(sd, false); | 
|  |  | 
|  | /* read status */ | 
|  | irq_status[0] = io_read(sd, 0x43); | 
|  | irq_status[1] = io_read(sd, 0x57); | 
|  | irq_status[2] = io_read(sd, 0x70); | 
|  | irq_status[3] = io_read(sd, 0x75); | 
|  | irq_status[4] = io_read(sd, 0x9d); | 
|  | irq_status[5] = io_read(sd, 0x66); | 
|  |  | 
|  | /* and clear */ | 
|  | if (irq_status[0]) | 
|  | io_write(sd, 0x44, irq_status[0]); | 
|  | if (irq_status[1]) | 
|  | io_write(sd, 0x58, irq_status[1]); | 
|  | if (irq_status[2]) | 
|  | io_write(sd, 0x71, irq_status[2]); | 
|  | if (irq_status[3]) | 
|  | io_write(sd, 0x76, irq_status[3]); | 
|  | if (irq_status[4]) | 
|  | io_write(sd, 0x9e, irq_status[4]); | 
|  | if (irq_status[5]) | 
|  | io_write(sd, 0x67, irq_status[5]); | 
|  |  | 
|  | adv7842_irq_enable(sd, true); | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s: irq %x, %x, %x, %x, %x, %x\n", __func__, | 
|  | irq_status[0], irq_status[1], irq_status[2], | 
|  | irq_status[3], irq_status[4], irq_status[5]); | 
|  |  | 
|  | /* format change CP */ | 
|  | fmt_change_cp = irq_status[0] & 0x9c; | 
|  |  | 
|  | /* format change SDP */ | 
|  | if (state->mode == ADV7842_MODE_SDP) | 
|  | fmt_change_sdp = (irq_status[1] & 0x30) | (irq_status[4] & 0x09); | 
|  | else | 
|  | fmt_change_sdp = 0; | 
|  |  | 
|  | /* digital format CP */ | 
|  | if (is_digital_input(sd)) | 
|  | fmt_change_digital = irq_status[3] & 0x03; | 
|  | else | 
|  | fmt_change_digital = 0; | 
|  |  | 
|  | /* format change */ | 
|  | if (fmt_change_cp || fmt_change_digital || fmt_change_sdp) { | 
|  | v4l2_dbg(1, debug, sd, | 
|  | "%s: fmt_change_cp = 0x%x, fmt_change_digital = 0x%x, fmt_change_sdp = 0x%x\n", | 
|  | __func__, fmt_change_cp, fmt_change_digital, | 
|  | fmt_change_sdp); | 
|  | v4l2_subdev_notify_event(sd, &adv7842_ev_fmt); | 
|  | if (handled) | 
|  | *handled = true; | 
|  | } | 
|  |  | 
|  | /* HDMI/DVI mode */ | 
|  | if (irq_status[5] & 0x08) { | 
|  | v4l2_dbg(1, debug, sd, "%s: irq %s mode\n", __func__, | 
|  | (io_read(sd, 0x65) & 0x08) ? "HDMI" : "DVI"); | 
|  | set_rgb_quantization_range(sd); | 
|  | if (handled) | 
|  | *handled = true; | 
|  | } | 
|  |  | 
|  | #if IS_ENABLED(CONFIG_VIDEO_ADV7842_CEC) | 
|  | /* cec */ | 
|  | adv7842_cec_isr(sd, handled); | 
|  | #endif | 
|  |  | 
|  | /* tx 5v detect */ | 
|  | if (irq_status[2] & 0x3) { | 
|  | v4l2_dbg(1, debug, sd, "%s: irq tx_5v\n", __func__); | 
|  | adv7842_s_detect_tx_5v_ctrl(sd); | 
|  | if (handled) | 
|  | *handled = true; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_get_edid(struct v4l2_subdev *sd, struct v4l2_edid *edid) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | u32 blocks = 0; | 
|  | u8 *data = NULL; | 
|  |  | 
|  | memset(edid->reserved, 0, sizeof(edid->reserved)); | 
|  |  | 
|  | switch (edid->pad) { | 
|  | case ADV7842_EDID_PORT_A: | 
|  | case ADV7842_EDID_PORT_B: | 
|  | if (state->hdmi_edid.present & (0x04 << edid->pad)) { | 
|  | data = state->hdmi_edid.edid; | 
|  | blocks = state->hdmi_edid.blocks; | 
|  | } | 
|  | break; | 
|  | case ADV7842_EDID_PORT_VGA: | 
|  | if (state->vga_edid.present) { | 
|  | data = state->vga_edid.edid; | 
|  | blocks = state->vga_edid.blocks; | 
|  | } | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (edid->start_block == 0 && edid->blocks == 0) { | 
|  | edid->blocks = blocks; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | if (!data) | 
|  | return -ENODATA; | 
|  |  | 
|  | if (edid->start_block >= blocks) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (edid->start_block + edid->blocks > blocks) | 
|  | edid->blocks = blocks - edid->start_block; | 
|  |  | 
|  | memcpy(edid->edid, data + edid->start_block * 128, edid->blocks * 128); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * If the VGA_EDID_ENABLE bit is set (Repeater Map 0x7f, bit 7), then | 
|  | * the first two blocks of the EDID are for the HDMI, and the first block | 
|  | * of segment 1 (i.e. the third block of the EDID) is for VGA. | 
|  | * So if a VGA EDID is installed, then the maximum size of the HDMI EDID | 
|  | * is 2 blocks. | 
|  | */ | 
|  | static int adv7842_set_edid(struct v4l2_subdev *sd, struct v4l2_edid *e) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | unsigned int max_blocks = e->pad == ADV7842_EDID_PORT_VGA ? 1 : 4; | 
|  | int err = 0; | 
|  |  | 
|  | memset(e->reserved, 0, sizeof(e->reserved)); | 
|  |  | 
|  | if (e->pad > ADV7842_EDID_PORT_VGA) | 
|  | return -EINVAL; | 
|  | if (e->start_block != 0) | 
|  | return -EINVAL; | 
|  | if (e->pad < ADV7842_EDID_PORT_VGA && state->vga_edid.blocks) | 
|  | max_blocks = 2; | 
|  | if (e->pad == ADV7842_EDID_PORT_VGA && state->hdmi_edid.blocks > 2) | 
|  | return -EBUSY; | 
|  | if (e->blocks > max_blocks) { | 
|  | e->blocks = max_blocks; | 
|  | return -E2BIG; | 
|  | } | 
|  |  | 
|  | /* todo, per edid */ | 
|  | if (e->blocks) | 
|  | state->aspect_ratio = v4l2_calc_aspect_ratio(e->edid[0x15], | 
|  | e->edid[0x16]); | 
|  |  | 
|  | switch (e->pad) { | 
|  | case ADV7842_EDID_PORT_VGA: | 
|  | memset(state->vga_edid.edid, 0, sizeof(state->vga_edid.edid)); | 
|  | state->vga_edid.blocks = e->blocks; | 
|  | state->vga_edid.present = e->blocks ? 0x1 : 0x0; | 
|  | if (e->blocks) | 
|  | memcpy(state->vga_edid.edid, e->edid, 128); | 
|  | err = edid_write_vga_segment(sd); | 
|  | break; | 
|  | case ADV7842_EDID_PORT_A: | 
|  | case ADV7842_EDID_PORT_B: | 
|  | memset(state->hdmi_edid.edid, 0, sizeof(state->hdmi_edid.edid)); | 
|  | state->hdmi_edid.blocks = e->blocks; | 
|  | if (e->blocks) { | 
|  | state->hdmi_edid.present |= 0x04 << e->pad; | 
|  | memcpy(state->hdmi_edid.edid, e->edid, 128 * e->blocks); | 
|  | } else { | 
|  | state->hdmi_edid.present &= ~(0x04 << e->pad); | 
|  | adv7842_s_detect_tx_5v_ctrl(sd); | 
|  | } | 
|  | err = edid_write_hdmi_segment(sd, e->pad); | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | if (err < 0) | 
|  | v4l2_err(sd, "error %d writing edid on port %d\n", err, e->pad); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | struct adv7842_cfg_read_infoframe { | 
|  | const char *desc; | 
|  | u8 present_mask; | 
|  | u8 head_addr; | 
|  | u8 payload_addr; | 
|  | }; | 
|  |  | 
|  | static const struct adv7842_cfg_read_infoframe adv7842_cri[] = { | 
|  | { "AVI", 0x01, 0xe0, 0x00 }, | 
|  | { "Audio", 0x02, 0xe3, 0x1c }, | 
|  | { "SDP", 0x04, 0xe6, 0x2a }, | 
|  | { "Vendor", 0x10, 0xec, 0x54 } | 
|  | }; | 
|  |  | 
|  | static int adv7842_read_infoframe_buf(struct v4l2_subdev *sd, int index, | 
|  | u8 buf[V4L2_DEBUGFS_IF_MAX_LEN]) | 
|  | { | 
|  | const struct adv7842_cfg_read_infoframe *cri = &adv7842_cri[index]; | 
|  | int len, i; | 
|  |  | 
|  | if (!(io_read(sd, 0x60) & cri->present_mask)) { | 
|  | v4l2_dbg(1, debug, sd, | 
|  | "%s infoframe not received\n", cri->desc); | 
|  | return -ENOENT; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < 3; i++) | 
|  | buf[i] = infoframe_read(sd, cri->head_addr + i); | 
|  |  | 
|  | len = buf[2] + 1; | 
|  |  | 
|  | if (len + 3 > V4L2_DEBUGFS_IF_MAX_LEN) { | 
|  | v4l2_err(sd, "%s: invalid %s infoframe length %d\n", | 
|  | __func__, cri->desc, len); | 
|  | return -ENOENT; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < len; i++) | 
|  | buf[i + 3] = infoframe_read(sd, cri->payload_addr + i); | 
|  | return len + 3; | 
|  | } | 
|  |  | 
|  | static void adv7842_log_infoframes(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | struct device *dev = &client->dev; | 
|  | union hdmi_infoframe frame; | 
|  | u8 buffer[V4L2_DEBUGFS_IF_MAX_LEN] = {}; | 
|  | int len, i; | 
|  |  | 
|  | if (!(hdmi_read(sd, 0x05) & 0x80)) { | 
|  | v4l2_info(sd, "receive DVI-D signal, no infoframes\n"); | 
|  | return; | 
|  | } | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(adv7842_cri); i++) { | 
|  | len = adv7842_read_infoframe_buf(sd, i, buffer); | 
|  | if (len < 0) | 
|  | continue; | 
|  |  | 
|  | if (hdmi_infoframe_unpack(&frame, buffer, len) < 0) | 
|  | v4l2_err(sd, "%s: unpack of %s infoframe failed\n", | 
|  | __func__, adv7842_cri[i].desc); | 
|  | else | 
|  | hdmi_infoframe_log(KERN_INFO, dev, &frame); | 
|  | } | 
|  | } | 
|  |  | 
|  | #if 0 | 
|  | /* Let's keep it here for now, as it could be useful for debug */ | 
|  | static const char * const prim_mode_txt[] = { | 
|  | "SDP", | 
|  | "Component", | 
|  | "Graphics", | 
|  | "Reserved", | 
|  | "CVBS & HDMI AUDIO", | 
|  | "HDMI-Comp", | 
|  | "HDMI-GR", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | "Reserved", | 
|  | }; | 
|  | #endif | 
|  |  | 
|  | static int adv7842_sdp_log_status(struct v4l2_subdev *sd) | 
|  | { | 
|  | /* SDP (Standard definition processor) block */ | 
|  | u8 sdp_signal_detected = sdp_read(sd, 0x5A) & 0x01; | 
|  |  | 
|  | v4l2_info(sd, "Chip powered %s\n", no_power(sd) ? "off" : "on"); | 
|  | v4l2_info(sd, "Prim-mode = 0x%x, video std = 0x%x\n", | 
|  | io_read(sd, 0x01) & 0x0f, io_read(sd, 0x00) & 0x3f); | 
|  |  | 
|  | v4l2_info(sd, "SDP: free run: %s\n", | 
|  | (sdp_read(sd, 0x56) & 0x01) ? "on" : "off"); | 
|  | v4l2_info(sd, "SDP: %s\n", sdp_signal_detected ? | 
|  | "valid SD/PR signal detected" : "invalid/no signal"); | 
|  | if (sdp_signal_detected) { | 
|  | static const char * const sdp_std_txt[] = { | 
|  | "NTSC-M/J", | 
|  | "1?", | 
|  | "NTSC-443", | 
|  | "60HzSECAM", | 
|  | "PAL-M", | 
|  | "5?", | 
|  | "PAL-60", | 
|  | "7?", "8?", "9?", "a?", "b?", | 
|  | "PAL-CombN", | 
|  | "d?", | 
|  | "PAL-BGHID", | 
|  | "SECAM" | 
|  | }; | 
|  | v4l2_info(sd, "SDP: standard %s\n", | 
|  | sdp_std_txt[sdp_read(sd, 0x52) & 0x0f]); | 
|  | v4l2_info(sd, "SDP: %s\n", | 
|  | (sdp_read(sd, 0x59) & 0x08) ? "50Hz" : "60Hz"); | 
|  | v4l2_info(sd, "SDP: %s\n", | 
|  | (sdp_read(sd, 0x57) & 0x08) ? "Interlaced" : "Progressive"); | 
|  | v4l2_info(sd, "SDP: deinterlacer %s\n", | 
|  | (sdp_read(sd, 0x12) & 0x08) ? "enabled" : "disabled"); | 
|  | v4l2_info(sd, "SDP: csc %s mode\n", | 
|  | (sdp_io_read(sd, 0xe0) & 0x40) ? "auto" : "manual"); | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_cp_log_status(struct v4l2_subdev *sd) | 
|  | { | 
|  | /* CP block */ | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct v4l2_dv_timings timings; | 
|  | u8 reg_io_0x02 = io_read(sd, 0x02); | 
|  | u8 reg_io_0x21 = io_read(sd, 0x21); | 
|  | u8 reg_rep_0x77 = rep_read(sd, 0x77); | 
|  | u8 reg_rep_0x7d = rep_read(sd, 0x7d); | 
|  | bool audio_pll_locked = hdmi_read(sd, 0x04) & 0x01; | 
|  | bool audio_sample_packet_detect = hdmi_read(sd, 0x18) & 0x01; | 
|  | bool audio_mute = io_read(sd, 0x65) & 0x40; | 
|  |  | 
|  | static const char * const csc_coeff_sel_rb[16] = { | 
|  | "bypassed", "YPbPr601 -> RGB", "reserved", "YPbPr709 -> RGB", | 
|  | "reserved", "RGB -> YPbPr601", "reserved", "RGB -> YPbPr709", | 
|  | "reserved", "YPbPr709 -> YPbPr601", "YPbPr601 -> YPbPr709", | 
|  | "reserved", "reserved", "reserved", "reserved", "manual" | 
|  | }; | 
|  | static const char * const input_color_space_txt[16] = { | 
|  | "RGB limited range (16-235)", "RGB full range (0-255)", | 
|  | "YCbCr Bt.601 (16-235)", "YCbCr Bt.709 (16-235)", | 
|  | "xvYCC Bt.601", "xvYCC Bt.709", | 
|  | "YCbCr Bt.601 (0-255)", "YCbCr Bt.709 (0-255)", | 
|  | "invalid", "invalid", "invalid", "invalid", "invalid", | 
|  | "invalid", "invalid", "automatic" | 
|  | }; | 
|  | static const char * const rgb_quantization_range_txt[] = { | 
|  | "Automatic", | 
|  | "RGB limited range (16-235)", | 
|  | "RGB full range (0-255)", | 
|  | }; | 
|  | static const char * const deep_color_mode_txt[4] = { | 
|  | "8-bits per channel", | 
|  | "10-bits per channel", | 
|  | "12-bits per channel", | 
|  | "16-bits per channel (not supported)" | 
|  | }; | 
|  |  | 
|  | v4l2_info(sd, "-----Chip status-----\n"); | 
|  | v4l2_info(sd, "Chip power: %s\n", no_power(sd) ? "off" : "on"); | 
|  | v4l2_info(sd, "HDMI/DVI-D port selected: %s\n", | 
|  | state->hdmi_port_a ? "A" : "B"); | 
|  | v4l2_info(sd, "EDID A %s, B %s\n", | 
|  | ((reg_rep_0x7d & 0x04) && (reg_rep_0x77 & 0x04)) ? | 
|  | "enabled" : "disabled", | 
|  | ((reg_rep_0x7d & 0x08) && (reg_rep_0x77 & 0x08)) ? | 
|  | "enabled" : "disabled"); | 
|  | v4l2_info(sd, "HPD A %s, B %s\n", | 
|  | reg_io_0x21 & 0x02 ? "enabled" : "disabled", | 
|  | reg_io_0x21 & 0x01 ? "enabled" : "disabled"); | 
|  | v4l2_info(sd, "CEC: %s\n", state->cec_enabled_adap ? | 
|  | "enabled" : "disabled"); | 
|  | if (state->cec_enabled_adap) { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < ADV7842_MAX_ADDRS; i++) { | 
|  | bool is_valid = state->cec_valid_addrs & (1 << i); | 
|  |  | 
|  | if (is_valid) | 
|  | v4l2_info(sd, "CEC Logical Address: 0x%x\n", | 
|  | state->cec_addr[i]); | 
|  | } | 
|  | } | 
|  |  | 
|  | v4l2_info(sd, "-----Signal status-----\n"); | 
|  | if (state->hdmi_port_a) { | 
|  | v4l2_info(sd, "Cable detected (+5V power): %s\n", | 
|  | io_read(sd, 0x6f) & 0x02 ? "true" : "false"); | 
|  | v4l2_info(sd, "TMDS signal detected: %s\n", | 
|  | (io_read(sd, 0x6a) & 0x02) ? "true" : "false"); | 
|  | v4l2_info(sd, "TMDS signal locked: %s\n", | 
|  | (io_read(sd, 0x6a) & 0x20) ? "true" : "false"); | 
|  | } else { | 
|  | v4l2_info(sd, "Cable detected (+5V power):%s\n", | 
|  | io_read(sd, 0x6f) & 0x01 ? "true" : "false"); | 
|  | v4l2_info(sd, "TMDS signal detected: %s\n", | 
|  | (io_read(sd, 0x6a) & 0x01) ? "true" : "false"); | 
|  | v4l2_info(sd, "TMDS signal locked: %s\n", | 
|  | (io_read(sd, 0x6a) & 0x10) ? "true" : "false"); | 
|  | } | 
|  | v4l2_info(sd, "CP free run: %s\n", | 
|  | (!!(cp_read(sd, 0xff) & 0x10) ? "on" : "off")); | 
|  | v4l2_info(sd, "Prim-mode = 0x%x, video std = 0x%x, v_freq = 0x%x\n", | 
|  | io_read(sd, 0x01) & 0x0f, io_read(sd, 0x00) & 0x3f, | 
|  | (io_read(sd, 0x01) & 0x70) >> 4); | 
|  |  | 
|  | v4l2_info(sd, "-----Video Timings-----\n"); | 
|  | if (no_cp_signal(sd)) { | 
|  | v4l2_info(sd, "STDI: not locked\n"); | 
|  | } else { | 
|  | u32 bl = ((cp_read(sd, 0xb1) & 0x3f) << 8) | cp_read(sd, 0xb2); | 
|  | u32 lcf = ((cp_read(sd, 0xb3) & 0x7) << 8) | cp_read(sd, 0xb4); | 
|  | u32 lcvs = cp_read(sd, 0xb3) >> 3; | 
|  | u32 fcl = ((cp_read(sd, 0xb8) & 0x1f) << 8) | cp_read(sd, 0xb9); | 
|  | char hs_pol = ((cp_read(sd, 0xb5) & 0x10) ? | 
|  | ((cp_read(sd, 0xb5) & 0x08) ? '+' : '-') : 'x'); | 
|  | char vs_pol = ((cp_read(sd, 0xb5) & 0x40) ? | 
|  | ((cp_read(sd, 0xb5) & 0x20) ? '+' : '-') : 'x'); | 
|  | v4l2_info(sd, | 
|  | "STDI: lcf (frame height - 1) = %d, bl = %d, lcvs (vsync) = %d, fcl = %d, %s, %chsync, %cvsync\n", | 
|  | lcf, bl, lcvs, fcl, | 
|  | (cp_read(sd, 0xb1) & 0x40) ? | 
|  | "interlaced" : "progressive", | 
|  | hs_pol, vs_pol); | 
|  | } | 
|  | if (adv7842_query_dv_timings(sd, 0, &timings)) | 
|  | v4l2_info(sd, "No video detected\n"); | 
|  | else | 
|  | v4l2_print_dv_timings(sd->name, "Detected format: ", | 
|  | &timings, true); | 
|  | v4l2_print_dv_timings(sd->name, "Configured format: ", | 
|  | &state->timings, true); | 
|  |  | 
|  | if (no_cp_signal(sd)) | 
|  | return 0; | 
|  |  | 
|  | v4l2_info(sd, "-----Color space-----\n"); | 
|  | v4l2_info(sd, "RGB quantization range ctrl: %s\n", | 
|  | rgb_quantization_range_txt[state->rgb_quantization_range]); | 
|  | v4l2_info(sd, "Input color space: %s\n", | 
|  | input_color_space_txt[reg_io_0x02 >> 4]); | 
|  | v4l2_info(sd, "Output color space: %s %s, alt-gamma %s\n", | 
|  | (reg_io_0x02 & 0x02) ? "RGB" : "YCbCr", | 
|  | (((reg_io_0x02 >> 2) & 0x01) ^ (reg_io_0x02 & 0x01)) ? | 
|  | "(16-235)" : "(0-255)", | 
|  | (reg_io_0x02 & 0x08) ? "enabled" : "disabled"); | 
|  | v4l2_info(sd, "Color space conversion: %s\n", | 
|  | csc_coeff_sel_rb[cp_read(sd, 0xf4) >> 4]); | 
|  |  | 
|  | if (!is_digital_input(sd)) | 
|  | return 0; | 
|  |  | 
|  | v4l2_info(sd, "-----%s status-----\n", is_hdmi(sd) ? "HDMI" : "DVI-D"); | 
|  | v4l2_info(sd, "HDCP encrypted content: %s\n", | 
|  | (hdmi_read(sd, 0x05) & 0x40) ? "true" : "false"); | 
|  | v4l2_info(sd, "HDCP keys read: %s%s\n", | 
|  | (hdmi_read(sd, 0x04) & 0x20) ? "yes" : "no", | 
|  | (hdmi_read(sd, 0x04) & 0x10) ? "ERROR" : ""); | 
|  | if (!is_hdmi(sd)) | 
|  | return 0; | 
|  |  | 
|  | v4l2_info(sd, "Audio: pll %s, samples %s, %s\n", | 
|  | audio_pll_locked ? "locked" : "not locked", | 
|  | audio_sample_packet_detect ? "detected" : "not detected", | 
|  | audio_mute ? "muted" : "enabled"); | 
|  | if (audio_pll_locked && audio_sample_packet_detect) { | 
|  | v4l2_info(sd, "Audio format: %s\n", | 
|  | (hdmi_read(sd, 0x07) & 0x40) ? "multi-channel" : "stereo"); | 
|  | } | 
|  | v4l2_info(sd, "Audio CTS: %u\n", (hdmi_read(sd, 0x5b) << 12) + | 
|  | (hdmi_read(sd, 0x5c) << 8) + | 
|  | (hdmi_read(sd, 0x5d) & 0xf0)); | 
|  | v4l2_info(sd, "Audio N: %u\n", ((hdmi_read(sd, 0x5d) & 0x0f) << 16) + | 
|  | (hdmi_read(sd, 0x5e) << 8) + | 
|  | hdmi_read(sd, 0x5f)); | 
|  | v4l2_info(sd, "AV Mute: %s\n", | 
|  | (hdmi_read(sd, 0x04) & 0x40) ? "on" : "off"); | 
|  | v4l2_info(sd, "Deep color mode: %s\n", | 
|  | deep_color_mode_txt[hdmi_read(sd, 0x0b) >> 6]); | 
|  |  | 
|  | adv7842_log_infoframes(sd); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_log_status(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | if (state->mode == ADV7842_MODE_SDP) | 
|  | return adv7842_sdp_log_status(sd); | 
|  | return adv7842_cp_log_status(sd); | 
|  | } | 
|  |  | 
|  | static int adv7842_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s:\n", __func__); | 
|  |  | 
|  | if (state->mode != ADV7842_MODE_SDP) | 
|  | return -ENODATA; | 
|  |  | 
|  | if (!(sdp_read(sd, 0x5A) & 0x01)) { | 
|  | *std = 0; | 
|  | v4l2_dbg(1, debug, sd, "%s: no valid signal\n", __func__); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | switch (sdp_read(sd, 0x52) & 0x0f) { | 
|  | case 0: | 
|  | /* NTSC-M/J */ | 
|  | *std &= V4L2_STD_NTSC; | 
|  | break; | 
|  | case 2: | 
|  | /* NTSC-443 */ | 
|  | *std &= V4L2_STD_NTSC_443; | 
|  | break; | 
|  | case 3: | 
|  | /* 60HzSECAM */ | 
|  | *std &= V4L2_STD_SECAM; | 
|  | break; | 
|  | case 4: | 
|  | /* PAL-M */ | 
|  | *std &= V4L2_STD_PAL_M; | 
|  | break; | 
|  | case 6: | 
|  | /* PAL-60 */ | 
|  | *std &= V4L2_STD_PAL_60; | 
|  | break; | 
|  | case 0xc: | 
|  | /* PAL-CombN */ | 
|  | *std &= V4L2_STD_PAL_Nc; | 
|  | break; | 
|  | case 0xe: | 
|  | /* PAL-BGHID */ | 
|  | *std &= V4L2_STD_PAL; | 
|  | break; | 
|  | case 0xf: | 
|  | /* SECAM */ | 
|  | *std &= V4L2_STD_SECAM; | 
|  | break; | 
|  | default: | 
|  | *std &= V4L2_STD_ALL; | 
|  | break; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void adv7842_s_sdp_io(struct v4l2_subdev *sd, struct adv7842_sdp_io_sync_adjustment *s) | 
|  | { | 
|  | if (s && s->adjust) { | 
|  | sdp_io_write(sd, 0x94, (s->hs_beg >> 8) & 0xf); | 
|  | sdp_io_write(sd, 0x95, s->hs_beg & 0xff); | 
|  | sdp_io_write(sd, 0x96, (s->hs_width >> 8) & 0xf); | 
|  | sdp_io_write(sd, 0x97, s->hs_width & 0xff); | 
|  | sdp_io_write(sd, 0x98, (s->de_beg >> 8) & 0xf); | 
|  | sdp_io_write(sd, 0x99, s->de_beg & 0xff); | 
|  | sdp_io_write(sd, 0x9a, (s->de_end >> 8) & 0xf); | 
|  | sdp_io_write(sd, 0x9b, s->de_end & 0xff); | 
|  | sdp_io_write(sd, 0xa8, s->vs_beg_o); | 
|  | sdp_io_write(sd, 0xa9, s->vs_beg_e); | 
|  | sdp_io_write(sd, 0xaa, s->vs_end_o); | 
|  | sdp_io_write(sd, 0xab, s->vs_end_e); | 
|  | sdp_io_write(sd, 0xac, s->de_v_beg_o); | 
|  | sdp_io_write(sd, 0xad, s->de_v_beg_e); | 
|  | sdp_io_write(sd, 0xae, s->de_v_end_o); | 
|  | sdp_io_write(sd, 0xaf, s->de_v_end_e); | 
|  | } else { | 
|  | /* set to default */ | 
|  | sdp_io_write(sd, 0x94, 0x00); | 
|  | sdp_io_write(sd, 0x95, 0x00); | 
|  | sdp_io_write(sd, 0x96, 0x00); | 
|  | sdp_io_write(sd, 0x97, 0x20); | 
|  | sdp_io_write(sd, 0x98, 0x00); | 
|  | sdp_io_write(sd, 0x99, 0x00); | 
|  | sdp_io_write(sd, 0x9a, 0x00); | 
|  | sdp_io_write(sd, 0x9b, 0x00); | 
|  | sdp_io_write(sd, 0xa8, 0x04); | 
|  | sdp_io_write(sd, 0xa9, 0x04); | 
|  | sdp_io_write(sd, 0xaa, 0x04); | 
|  | sdp_io_write(sd, 0xab, 0x04); | 
|  | sdp_io_write(sd, 0xac, 0x04); | 
|  | sdp_io_write(sd, 0xad, 0x04); | 
|  | sdp_io_write(sd, 0xae, 0x04); | 
|  | sdp_io_write(sd, 0xaf, 0x04); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int adv7842_s_std(struct v4l2_subdev *sd, v4l2_std_id norm) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct adv7842_platform_data *pdata = &state->pdata; | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s:\n", __func__); | 
|  |  | 
|  | if (state->mode != ADV7842_MODE_SDP) | 
|  | return -ENODATA; | 
|  |  | 
|  | if (norm & V4L2_STD_625_50) | 
|  | adv7842_s_sdp_io(sd, &pdata->sdp_io_sync_625); | 
|  | else if (norm & V4L2_STD_525_60) | 
|  | adv7842_s_sdp_io(sd, &pdata->sdp_io_sync_525); | 
|  | else | 
|  | adv7842_s_sdp_io(sd, NULL); | 
|  |  | 
|  | if (norm & V4L2_STD_ALL) { | 
|  | state->norm = norm; | 
|  | return 0; | 
|  | } | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static int adv7842_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, "%s:\n", __func__); | 
|  |  | 
|  | if (state->mode != ADV7842_MODE_SDP) | 
|  | return -ENODATA; | 
|  |  | 
|  | *norm = state->norm; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static int adv7842_core_init(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct adv7842_platform_data *pdata = &state->pdata; | 
|  | hdmi_write(sd, 0x48, | 
|  | (pdata->disable_pwrdnb ? 0x80 : 0) | | 
|  | (pdata->disable_cable_det_rst ? 0x40 : 0)); | 
|  |  | 
|  | disable_input(sd); | 
|  |  | 
|  | /* | 
|  | * Disable I2C access to internal EDID ram from HDMI DDC ports | 
|  | * Disable auto edid enable when leaving powerdown mode | 
|  | */ | 
|  | rep_write_and_or(sd, 0x77, 0xd3, 0x20); | 
|  |  | 
|  | /* power */ | 
|  | io_write(sd, 0x0c, 0x42);   /* Power up part and power down VDP */ | 
|  | io_write(sd, 0x15, 0x80);   /* Power up pads */ | 
|  |  | 
|  | /* video format */ | 
|  | io_write(sd, 0x02, 0xf0 | pdata->alt_gamma << 3); | 
|  | io_write_and_or(sd, 0x05, 0xf0, pdata->blank_data << 3 | | 
|  | pdata->insert_av_codes << 2 | | 
|  | pdata->replicate_av_codes << 1); | 
|  | adv7842_setup_format(state); | 
|  |  | 
|  | /* HDMI audio */ | 
|  | hdmi_write_and_or(sd, 0x1a, 0xf1, 0x08); /* Wait 1 s before unmute */ | 
|  |  | 
|  | /* Drive strength */ | 
|  | io_write_and_or(sd, 0x14, 0xc0, | 
|  | pdata->dr_str_data << 4 | | 
|  | pdata->dr_str_clk << 2 | | 
|  | pdata->dr_str_sync); | 
|  |  | 
|  | /* HDMI free run */ | 
|  | cp_write_and_or(sd, 0xba, 0xfc, pdata->hdmi_free_run_enable | | 
|  | (pdata->hdmi_free_run_mode << 1)); | 
|  |  | 
|  | /* SPD free run */ | 
|  | sdp_write_and_or(sd, 0xdd, 0xf0, pdata->sdp_free_run_force | | 
|  | (pdata->sdp_free_run_cbar_en << 1) | | 
|  | (pdata->sdp_free_run_man_col_en << 2) | | 
|  | (pdata->sdp_free_run_auto << 3)); | 
|  |  | 
|  | /* TODO from platform data */ | 
|  | cp_write(sd, 0x69, 0x14);   /* Enable CP CSC */ | 
|  | io_write(sd, 0x06, 0xa6);   /* positive VS and HS and DE */ | 
|  | cp_write(sd, 0xf3, 0xdc); /* Low threshold to enter/exit free run mode */ | 
|  | afe_write(sd, 0xb5, 0x01);  /* Setting MCLK to 256Fs */ | 
|  |  | 
|  | afe_write(sd, 0x02, pdata->ain_sel); /* Select analog input muxing mode */ | 
|  | io_write_and_or(sd, 0x30, ~(1 << 4), pdata->output_bus_lsb_to_msb << 4); | 
|  |  | 
|  | sdp_csc_coeff(sd, &pdata->sdp_csc_coeff); | 
|  |  | 
|  | /* todo, improve settings for sdram */ | 
|  | if (pdata->sd_ram_size >= 128) { | 
|  | sdp_write(sd, 0x12, 0x0d); /* Frame TBC,3D comb enabled */ | 
|  | if (pdata->sd_ram_ddr) { | 
|  | /* SDP setup for the AD eval board */ | 
|  | sdp_io_write(sd, 0x6f, 0x00); /* DDR mode */ | 
|  | sdp_io_write(sd, 0x75, 0x0a); /* 128 MB memory size */ | 
|  | sdp_io_write(sd, 0x7a, 0xa5); /* Timing Adjustment */ | 
|  | sdp_io_write(sd, 0x7b, 0x8f); /* Timing Adjustment */ | 
|  | sdp_io_write(sd, 0x60, 0x01); /* SDRAM reset */ | 
|  | } else { | 
|  | sdp_io_write(sd, 0x75, 0x0a); /* 64 MB memory size ?*/ | 
|  | sdp_io_write(sd, 0x74, 0x00); /* must be zero for sdr sdram */ | 
|  | sdp_io_write(sd, 0x79, 0x33); /* CAS latency to 3, | 
|  | depends on memory */ | 
|  | sdp_io_write(sd, 0x6f, 0x01); /* SDR mode */ | 
|  | sdp_io_write(sd, 0x7a, 0xa5); /* Timing Adjustment */ | 
|  | sdp_io_write(sd, 0x7b, 0x8f); /* Timing Adjustment */ | 
|  | sdp_io_write(sd, 0x60, 0x01); /* SDRAM reset */ | 
|  | } | 
|  | } else { | 
|  | /* | 
|  | * Manual UG-214, rev 0 is bit confusing on this bit | 
|  | * but a '1' disables any signal if the Ram is active. | 
|  | */ | 
|  | sdp_io_write(sd, 0x29, 0x10); /* Tristate memory interface */ | 
|  | } | 
|  |  | 
|  | select_input(sd, pdata->vid_std_select); | 
|  |  | 
|  | enable_input(sd); | 
|  |  | 
|  | if (pdata->hpa_auto) { | 
|  | /* HPA auto, HPA 0.5s after Edid set and Cable detect */ | 
|  | hdmi_write(sd, 0x69, 0x5c); | 
|  | } else { | 
|  | /* HPA manual */ | 
|  | hdmi_write(sd, 0x69, 0xa3); | 
|  | /* HPA disable on port A and B */ | 
|  | io_write_and_or(sd, 0x20, 0xcf, 0x00); | 
|  | } | 
|  |  | 
|  | /* LLC */ | 
|  | io_write(sd, 0x19, 0x80 | pdata->llc_dll_phase); | 
|  | io_write(sd, 0x33, 0x40); | 
|  |  | 
|  | /* interrupts */ | 
|  | io_write(sd, 0x40, 0xf2); /* Configure INT1 */ | 
|  |  | 
|  | adv7842_irq_enable(sd, true); | 
|  |  | 
|  | return v4l2_ctrl_handler_setup(sd->ctrl_handler); | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static int adv7842_ddr_ram_test(struct v4l2_subdev *sd) | 
|  | { | 
|  | /* | 
|  | * From ADV784x external Memory test.pdf | 
|  | * | 
|  | * Reset must just been performed before running test. | 
|  | * Recommended to reset after test. | 
|  | */ | 
|  | int i; | 
|  | int pass = 0; | 
|  | int fail = 0; | 
|  | int complete = 0; | 
|  |  | 
|  | io_write(sd, 0x00, 0x01);  /* Program SDP 4x1 */ | 
|  | io_write(sd, 0x01, 0x00);  /* Program SDP mode */ | 
|  | afe_write(sd, 0x80, 0x92); /* SDP Recommended Write */ | 
|  | afe_write(sd, 0x9B, 0x01); /* SDP Recommended Write ADV7844ES1 */ | 
|  | afe_write(sd, 0x9C, 0x60); /* SDP Recommended Write ADV7844ES1 */ | 
|  | afe_write(sd, 0x9E, 0x02); /* SDP Recommended Write ADV7844ES1 */ | 
|  | afe_write(sd, 0xA0, 0x0B); /* SDP Recommended Write ADV7844ES1 */ | 
|  | afe_write(sd, 0xC3, 0x02); /* Memory BIST Initialisation */ | 
|  | io_write(sd, 0x0C, 0x40);  /* Power up ADV7844 */ | 
|  | io_write(sd, 0x15, 0xBA);  /* Enable outputs */ | 
|  | sdp_write(sd, 0x12, 0x00); /* Disable 3D comb, Frame TBC & 3DNR */ | 
|  | io_write(sd, 0xFF, 0x04);  /* Reset memory controller */ | 
|  |  | 
|  | usleep_range(5000, 6000); | 
|  |  | 
|  | sdp_write(sd, 0x12, 0x00);    /* Disable 3D Comb, Frame TBC & 3DNR */ | 
|  | sdp_io_write(sd, 0x2A, 0x01); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x7c, 0x19); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x80, 0x87); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x81, 0x4a); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x82, 0x2c); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x83, 0x0e); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x84, 0x94); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x85, 0x62); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x7d, 0x00); /* Memory BIST Initialisation */ | 
|  | sdp_io_write(sd, 0x7e, 0x1a); /* Memory BIST Initialisation */ | 
|  |  | 
|  | usleep_range(5000, 6000); | 
|  |  | 
|  | sdp_io_write(sd, 0xd9, 0xd5); /* Enable BIST Test */ | 
|  | sdp_write(sd, 0x12, 0x05); /* Enable FRAME TBC & 3D COMB */ | 
|  |  | 
|  | msleep(20); | 
|  |  | 
|  | for (i = 0; i < 10; i++) { | 
|  | u8 result = sdp_io_read(sd, 0xdb); | 
|  | if (result & 0x10) { | 
|  | complete++; | 
|  | if (result & 0x20) | 
|  | fail++; | 
|  | else | 
|  | pass++; | 
|  | } | 
|  | msleep(20); | 
|  | } | 
|  |  | 
|  | v4l2_dbg(1, debug, sd, | 
|  | "Ram Test: completed %d of %d: pass %d, fail %d\n", | 
|  | complete, i, pass, fail); | 
|  |  | 
|  | if (!complete || fail) | 
|  | return -EIO; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void adv7842_rewrite_i2c_addresses(struct v4l2_subdev *sd, | 
|  | struct adv7842_platform_data *pdata) | 
|  | { | 
|  | io_write(sd, 0xf1, pdata->i2c_sdp << 1); | 
|  | io_write(sd, 0xf2, pdata->i2c_sdp_io << 1); | 
|  | io_write(sd, 0xf3, pdata->i2c_avlink << 1); | 
|  | io_write(sd, 0xf4, pdata->i2c_cec << 1); | 
|  | io_write(sd, 0xf5, pdata->i2c_infoframe << 1); | 
|  |  | 
|  | io_write(sd, 0xf8, pdata->i2c_afe << 1); | 
|  | io_write(sd, 0xf9, pdata->i2c_repeater << 1); | 
|  | io_write(sd, 0xfa, pdata->i2c_edid << 1); | 
|  | io_write(sd, 0xfb, pdata->i2c_hdmi << 1); | 
|  |  | 
|  | io_write(sd, 0xfd, pdata->i2c_cp << 1); | 
|  | io_write(sd, 0xfe, pdata->i2c_vdp << 1); | 
|  | } | 
|  |  | 
|  | static int adv7842_command_ram_test(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct adv7842_platform_data *pdata = client->dev.platform_data; | 
|  | struct v4l2_dv_timings timings; | 
|  | int ret = 0; | 
|  |  | 
|  | if (!pdata) | 
|  | return -ENODEV; | 
|  |  | 
|  | if (!pdata->sd_ram_size || !pdata->sd_ram_ddr) { | 
|  | v4l2_info(sd, "no sdram or no ddr sdram\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | main_reset(sd); | 
|  |  | 
|  | adv7842_rewrite_i2c_addresses(sd, pdata); | 
|  |  | 
|  | /* run ram test */ | 
|  | ret = adv7842_ddr_ram_test(sd); | 
|  |  | 
|  | main_reset(sd); | 
|  |  | 
|  | adv7842_rewrite_i2c_addresses(sd, pdata); | 
|  |  | 
|  | /* and re-init chip and state */ | 
|  | adv7842_core_init(sd); | 
|  |  | 
|  | disable_input(sd); | 
|  |  | 
|  | select_input(sd, state->vid_std_select); | 
|  |  | 
|  | enable_input(sd); | 
|  |  | 
|  | edid_write_vga_segment(sd); | 
|  | edid_write_hdmi_segment(sd, ADV7842_EDID_PORT_A); | 
|  | edid_write_hdmi_segment(sd, ADV7842_EDID_PORT_B); | 
|  |  | 
|  | timings = state->timings; | 
|  |  | 
|  | memset(&state->timings, 0, sizeof(struct v4l2_dv_timings)); | 
|  |  | 
|  | adv7842_s_dv_timings(sd, 0, &timings); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static long adv7842_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg) | 
|  | { | 
|  | switch (cmd) { | 
|  | case ADV7842_CMD_RAM_TEST: | 
|  | return adv7842_command_ram_test(sd); | 
|  | } | 
|  | return -ENOTTY; | 
|  | } | 
|  |  | 
|  | static int adv7842_subscribe_event(struct v4l2_subdev *sd, | 
|  | struct v4l2_fh *fh, | 
|  | struct v4l2_event_subscription *sub) | 
|  | { | 
|  | switch (sub->type) { | 
|  | case V4L2_EVENT_SOURCE_CHANGE: | 
|  | return v4l2_src_change_event_subdev_subscribe(sd, fh, sub); | 
|  | case V4L2_EVENT_CTRL: | 
|  | return v4l2_ctrl_subdev_subscribe_event(sd, fh, sub); | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | } | 
|  |  | 
|  | static ssize_t | 
|  | adv7842_debugfs_if_read(u32 type, void *priv, struct file *filp, | 
|  | char __user *ubuf, size_t count, loff_t *ppos) | 
|  | { | 
|  | u8 buf[V4L2_DEBUGFS_IF_MAX_LEN] = {}; | 
|  | struct v4l2_subdev *sd = priv; | 
|  | int index; | 
|  | int len; | 
|  |  | 
|  | if (!is_hdmi(sd)) | 
|  | return 0; | 
|  |  | 
|  | switch (type) { | 
|  | case V4L2_DEBUGFS_IF_AVI: | 
|  | index = 0; | 
|  | break; | 
|  | case V4L2_DEBUGFS_IF_AUDIO: | 
|  | index = 1; | 
|  | break; | 
|  | case V4L2_DEBUGFS_IF_SPD: | 
|  | index = 2; | 
|  | break; | 
|  | case V4L2_DEBUGFS_IF_HDMI: | 
|  | index = 3; | 
|  | break; | 
|  | default: | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | len = adv7842_read_infoframe_buf(sd, index, buf); | 
|  | if (len > 0) | 
|  | len = simple_read_from_buffer(ubuf, count, ppos, buf, len); | 
|  | return len < 0 ? 0 : len; | 
|  | } | 
|  |  | 
|  | static int adv7842_registered(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | int err; | 
|  |  | 
|  | err = cec_register_adapter(state->cec_adap, &client->dev); | 
|  | if (err) { | 
|  | cec_delete_adapter(state->cec_adap); | 
|  | } else { | 
|  | state->debugfs_dir = debugfs_create_dir(sd->name, v4l2_debugfs_root()); | 
|  | state->infoframes = v4l2_debugfs_if_alloc(state->debugfs_dir, | 
|  | V4L2_DEBUGFS_IF_AVI | V4L2_DEBUGFS_IF_AUDIO | | 
|  | V4L2_DEBUGFS_IF_SPD | V4L2_DEBUGFS_IF_HDMI, sd, | 
|  | adv7842_debugfs_if_read); | 
|  | } | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static void adv7842_unregistered(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | cec_unregister_adapter(state->cec_adap); | 
|  | v4l2_debugfs_if_free(state->infoframes); | 
|  | state->infoframes = NULL; | 
|  | debugfs_remove_recursive(state->debugfs_dir); | 
|  | state->debugfs_dir = NULL; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static const struct v4l2_ctrl_ops adv7842_ctrl_ops = { | 
|  | .s_ctrl = adv7842_s_ctrl, | 
|  | .g_volatile_ctrl = adv7842_g_volatile_ctrl, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_core_ops adv7842_core_ops = { | 
|  | .log_status = adv7842_log_status, | 
|  | .ioctl = adv7842_ioctl, | 
|  | .interrupt_service_routine = adv7842_isr, | 
|  | .subscribe_event = adv7842_subscribe_event, | 
|  | .unsubscribe_event = v4l2_event_subdev_unsubscribe, | 
|  | #ifdef CONFIG_VIDEO_ADV_DEBUG | 
|  | .g_register = adv7842_g_register, | 
|  | .s_register = adv7842_s_register, | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_video_ops adv7842_video_ops = { | 
|  | .g_std = adv7842_g_std, | 
|  | .s_std = adv7842_s_std, | 
|  | .s_routing = adv7842_s_routing, | 
|  | .querystd = adv7842_querystd, | 
|  | .g_input_status = adv7842_g_input_status, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_pad_ops adv7842_pad_ops = { | 
|  | .enum_mbus_code = adv7842_enum_mbus_code, | 
|  | .get_fmt = adv7842_get_format, | 
|  | .set_fmt = adv7842_set_format, | 
|  | .get_edid = adv7842_get_edid, | 
|  | .set_edid = adv7842_set_edid, | 
|  | .s_dv_timings = adv7842_s_dv_timings, | 
|  | .g_dv_timings = adv7842_g_dv_timings, | 
|  | .query_dv_timings = adv7842_query_dv_timings, | 
|  | .enum_dv_timings = adv7842_enum_dv_timings, | 
|  | .dv_timings_cap = adv7842_dv_timings_cap, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_ops adv7842_ops = { | 
|  | .core = &adv7842_core_ops, | 
|  | .video = &adv7842_video_ops, | 
|  | .pad = &adv7842_pad_ops, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_internal_ops adv7842_int_ops = { | 
|  | .registered = adv7842_registered, | 
|  | .unregistered = adv7842_unregistered, | 
|  | }; | 
|  |  | 
|  | /* -------------------------- custom ctrls ---------------------------------- */ | 
|  |  | 
|  | static const struct v4l2_ctrl_config adv7842_ctrl_analog_sampling_phase = { | 
|  | .ops = &adv7842_ctrl_ops, | 
|  | .id = V4L2_CID_ADV_RX_ANALOG_SAMPLING_PHASE, | 
|  | .name = "Analog Sampling Phase", | 
|  | .type = V4L2_CTRL_TYPE_INTEGER, | 
|  | .min = 0, | 
|  | .max = 0x1f, | 
|  | .step = 1, | 
|  | .def = 0, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_ctrl_config adv7842_ctrl_free_run_color_manual = { | 
|  | .ops = &adv7842_ctrl_ops, | 
|  | .id = V4L2_CID_ADV_RX_FREE_RUN_COLOR_MANUAL, | 
|  | .name = "Free Running Color, Manual", | 
|  | .type = V4L2_CTRL_TYPE_BOOLEAN, | 
|  | .max = 1, | 
|  | .step = 1, | 
|  | .def = 1, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_ctrl_config adv7842_ctrl_free_run_color = { | 
|  | .ops = &adv7842_ctrl_ops, | 
|  | .id = V4L2_CID_ADV_RX_FREE_RUN_COLOR, | 
|  | .name = "Free Running Color", | 
|  | .type = V4L2_CTRL_TYPE_INTEGER, | 
|  | .max = 0xffffff, | 
|  | .step = 0x1, | 
|  | }; | 
|  |  | 
|  |  | 
|  | static void adv7842_unregister_clients(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | i2c_unregister_device(state->i2c_avlink); | 
|  | i2c_unregister_device(state->i2c_cec); | 
|  | i2c_unregister_device(state->i2c_infoframe); | 
|  | i2c_unregister_device(state->i2c_sdp_io); | 
|  | i2c_unregister_device(state->i2c_sdp); | 
|  | i2c_unregister_device(state->i2c_afe); | 
|  | i2c_unregister_device(state->i2c_repeater); | 
|  | i2c_unregister_device(state->i2c_edid); | 
|  | i2c_unregister_device(state->i2c_hdmi); | 
|  | i2c_unregister_device(state->i2c_cp); | 
|  | i2c_unregister_device(state->i2c_vdp); | 
|  |  | 
|  | state->i2c_avlink = NULL; | 
|  | state->i2c_cec = NULL; | 
|  | state->i2c_infoframe = NULL; | 
|  | state->i2c_sdp_io = NULL; | 
|  | state->i2c_sdp = NULL; | 
|  | state->i2c_afe = NULL; | 
|  | state->i2c_repeater = NULL; | 
|  | state->i2c_edid = NULL; | 
|  | state->i2c_hdmi = NULL; | 
|  | state->i2c_cp = NULL; | 
|  | state->i2c_vdp = NULL; | 
|  | } | 
|  |  | 
|  | static struct i2c_client *adv7842_dummy_client(struct v4l2_subdev *sd, const char *desc, | 
|  | u8 addr, u8 io_reg) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  | struct i2c_client *cp; | 
|  |  | 
|  | io_write(sd, io_reg, addr << 1); | 
|  |  | 
|  | if (addr == 0) { | 
|  | v4l2_err(sd, "no %s i2c addr configured\n", desc); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | cp = i2c_new_dummy_device(client->adapter, io_read(sd, io_reg) >> 1); | 
|  | if (IS_ERR(cp)) { | 
|  | v4l2_err(sd, "register %s on i2c addr 0x%x failed with %ld\n", | 
|  | desc, addr, PTR_ERR(cp)); | 
|  | cp = NULL; | 
|  | } | 
|  |  | 
|  | return cp; | 
|  | } | 
|  |  | 
|  | static int adv7842_register_clients(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7842_state *state = to_state(sd); | 
|  | struct adv7842_platform_data *pdata = &state->pdata; | 
|  |  | 
|  | state->i2c_avlink = adv7842_dummy_client(sd, "avlink", pdata->i2c_avlink, 0xf3); | 
|  | state->i2c_cec = adv7842_dummy_client(sd, "cec", pdata->i2c_cec, 0xf4); | 
|  | state->i2c_infoframe = adv7842_dummy_client(sd, "infoframe", pdata->i2c_infoframe, 0xf5); | 
|  | state->i2c_sdp_io = adv7842_dummy_client(sd, "sdp_io", pdata->i2c_sdp_io, 0xf2); | 
|  | state->i2c_sdp = adv7842_dummy_client(sd, "sdp", pdata->i2c_sdp, 0xf1); | 
|  | state->i2c_afe = adv7842_dummy_client(sd, "afe", pdata->i2c_afe, 0xf8); | 
|  | state->i2c_repeater = adv7842_dummy_client(sd, "repeater", pdata->i2c_repeater, 0xf9); | 
|  | state->i2c_edid = adv7842_dummy_client(sd, "edid", pdata->i2c_edid, 0xfa); | 
|  | state->i2c_hdmi = adv7842_dummy_client(sd, "hdmi", pdata->i2c_hdmi, 0xfb); | 
|  | state->i2c_cp = adv7842_dummy_client(sd, "cp", pdata->i2c_cp, 0xfd); | 
|  | state->i2c_vdp = adv7842_dummy_client(sd, "vdp", pdata->i2c_vdp, 0xfe); | 
|  |  | 
|  | if (!state->i2c_avlink || | 
|  | !state->i2c_cec || | 
|  | !state->i2c_infoframe || | 
|  | !state->i2c_sdp_io || | 
|  | !state->i2c_sdp || | 
|  | !state->i2c_afe || | 
|  | !state->i2c_repeater || | 
|  | !state->i2c_edid || | 
|  | !state->i2c_hdmi || | 
|  | !state->i2c_cp || | 
|  | !state->i2c_vdp) | 
|  | return -1; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7842_probe(struct i2c_client *client) | 
|  | { | 
|  | struct adv7842_state *state; | 
|  | static const struct v4l2_dv_timings cea640x480 = | 
|  | V4L2_DV_BT_CEA_640X480P59_94; | 
|  | struct adv7842_platform_data *pdata = client->dev.platform_data; | 
|  | struct v4l2_ctrl_handler *hdl; | 
|  | struct v4l2_ctrl *ctrl; | 
|  | struct v4l2_subdev *sd; | 
|  | unsigned int i; | 
|  | u16 rev; | 
|  | int err; | 
|  |  | 
|  | /* Check if the adapter supports the needed features */ | 
|  | if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) | 
|  | return -EIO; | 
|  |  | 
|  | v4l_dbg(1, debug, client, "detecting adv7842 client on address 0x%x\n", | 
|  | client->addr << 1); | 
|  |  | 
|  | if (!pdata) { | 
|  | v4l_err(client, "No platform data!\n"); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | state = devm_kzalloc(&client->dev, sizeof(*state), GFP_KERNEL); | 
|  | if (!state) | 
|  | return -ENOMEM; | 
|  |  | 
|  | /* platform data */ | 
|  | state->pdata = *pdata; | 
|  | state->timings = cea640x480; | 
|  | state->format = adv7842_format_info(state, MEDIA_BUS_FMT_YUYV8_2X8); | 
|  |  | 
|  | sd = &state->sd; | 
|  | v4l2_i2c_subdev_init(sd, client, &adv7842_ops); | 
|  | sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS; | 
|  | sd->internal_ops = &adv7842_int_ops; | 
|  | state->mode = pdata->mode; | 
|  |  | 
|  | state->hdmi_port_a = pdata->input == ADV7842_SELECT_HDMI_PORT_A; | 
|  | state->restart_stdi_once = true; | 
|  |  | 
|  | /* i2c access to adv7842? */ | 
|  | rev = adv_smbus_read_byte_data_check(client, 0xea, false) << 8 | | 
|  | adv_smbus_read_byte_data_check(client, 0xeb, false); | 
|  | if (rev != 0x2012) { | 
|  | v4l2_info(sd, "got rev=0x%04x on first read attempt\n", rev); | 
|  | rev = adv_smbus_read_byte_data_check(client, 0xea, false) << 8 | | 
|  | adv_smbus_read_byte_data_check(client, 0xeb, false); | 
|  | } | 
|  | if (rev != 0x2012) { | 
|  | v4l2_info(sd, "not an adv7842 on address 0x%x (rev=0x%04x)\n", | 
|  | client->addr << 1, rev); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | if (pdata->chip_reset) | 
|  | main_reset(sd); | 
|  |  | 
|  | /* control handlers */ | 
|  | hdl = &state->hdl; | 
|  | v4l2_ctrl_handler_init(hdl, 6); | 
|  |  | 
|  | /* add in ascending ID order */ | 
|  | v4l2_ctrl_new_std(hdl, &adv7842_ctrl_ops, | 
|  | V4L2_CID_BRIGHTNESS, -128, 127, 1, 0); | 
|  | v4l2_ctrl_new_std(hdl, &adv7842_ctrl_ops, | 
|  | V4L2_CID_CONTRAST, 0, 255, 1, 128); | 
|  | v4l2_ctrl_new_std(hdl, &adv7842_ctrl_ops, | 
|  | V4L2_CID_SATURATION, 0, 255, 1, 128); | 
|  | v4l2_ctrl_new_std(hdl, &adv7842_ctrl_ops, | 
|  | V4L2_CID_HUE, 0, 128, 1, 0); | 
|  | ctrl = v4l2_ctrl_new_std_menu(hdl, &adv7842_ctrl_ops, | 
|  | V4L2_CID_DV_RX_IT_CONTENT_TYPE, V4L2_DV_IT_CONTENT_TYPE_NO_ITC, | 
|  | 0, V4L2_DV_IT_CONTENT_TYPE_NO_ITC); | 
|  | if (ctrl) | 
|  | ctrl->flags |= V4L2_CTRL_FLAG_VOLATILE; | 
|  |  | 
|  | /* custom controls */ | 
|  | state->detect_tx_5v_ctrl = v4l2_ctrl_new_std(hdl, NULL, | 
|  | V4L2_CID_DV_RX_POWER_PRESENT, 0, 3, 0, 0); | 
|  | state->analog_sampling_phase_ctrl = v4l2_ctrl_new_custom(hdl, | 
|  | &adv7842_ctrl_analog_sampling_phase, NULL); | 
|  | state->free_run_color_ctrl_manual = v4l2_ctrl_new_custom(hdl, | 
|  | &adv7842_ctrl_free_run_color_manual, NULL); | 
|  | state->free_run_color_ctrl = v4l2_ctrl_new_custom(hdl, | 
|  | &adv7842_ctrl_free_run_color, NULL); | 
|  | state->rgb_quantization_range_ctrl = | 
|  | v4l2_ctrl_new_std_menu(hdl, &adv7842_ctrl_ops, | 
|  | V4L2_CID_DV_RX_RGB_RANGE, V4L2_DV_RGB_RANGE_FULL, | 
|  | 0, V4L2_DV_RGB_RANGE_AUTO); | 
|  | sd->ctrl_handler = hdl; | 
|  | if (hdl->error) { | 
|  | err = hdl->error; | 
|  | goto err_hdl; | 
|  | } | 
|  | if (adv7842_s_detect_tx_5v_ctrl(sd)) { | 
|  | err = -ENODEV; | 
|  | goto err_hdl; | 
|  | } | 
|  |  | 
|  | if (adv7842_register_clients(sd) < 0) { | 
|  | err = -ENOMEM; | 
|  | v4l2_err(sd, "failed to create all i2c clients\n"); | 
|  | goto err_i2c; | 
|  | } | 
|  |  | 
|  |  | 
|  | INIT_DELAYED_WORK(&state->delayed_work_enable_hotplug, | 
|  | adv7842_delayed_work_enable_hotplug); | 
|  |  | 
|  | sd->entity.function = MEDIA_ENT_F_DV_DECODER; | 
|  | for (i = 0; i < ADV7842_PAD_SOURCE; ++i) | 
|  | state->pads[i].flags = MEDIA_PAD_FL_SINK; | 
|  | state->pads[ADV7842_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE; | 
|  | err = media_entity_pads_init(&sd->entity, ADV7842_PAD_SOURCE + 1, | 
|  | state->pads); | 
|  | if (err) | 
|  | goto err_work_queues; | 
|  |  | 
|  | err = adv7842_core_init(sd); | 
|  | if (err) | 
|  | goto err_entity; | 
|  |  | 
|  | #if IS_ENABLED(CONFIG_VIDEO_ADV7842_CEC) | 
|  | state->cec_adap = cec_allocate_adapter(&adv7842_cec_adap_ops, | 
|  | state, dev_name(&client->dev), | 
|  | CEC_CAP_DEFAULTS, ADV7842_MAX_ADDRS); | 
|  | err = PTR_ERR_OR_ZERO(state->cec_adap); | 
|  | if (err) | 
|  | goto err_entity; | 
|  | #endif | 
|  |  | 
|  | v4l2_info(sd, "%s found @ 0x%x (%s)\n", client->name, | 
|  | client->addr << 1, client->adapter->name); | 
|  | return 0; | 
|  |  | 
|  | err_entity: | 
|  | media_entity_cleanup(&sd->entity); | 
|  | err_work_queues: | 
|  | cancel_delayed_work(&state->delayed_work_enable_hotplug); | 
|  | err_i2c: | 
|  | adv7842_unregister_clients(sd); | 
|  | err_hdl: | 
|  | v4l2_ctrl_handler_free(hdl); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static void adv7842_remove(struct i2c_client *client) | 
|  | { | 
|  | struct v4l2_subdev *sd = i2c_get_clientdata(client); | 
|  | struct adv7842_state *state = to_state(sd); | 
|  |  | 
|  | adv7842_irq_enable(sd, false); | 
|  | cancel_delayed_work_sync(&state->delayed_work_enable_hotplug); | 
|  | v4l2_device_unregister_subdev(sd); | 
|  | media_entity_cleanup(&sd->entity); | 
|  | adv7842_unregister_clients(sd); | 
|  | v4l2_ctrl_handler_free(sd->ctrl_handler); | 
|  | } | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static const struct i2c_device_id adv7842_id[] = { | 
|  | { "adv7842" }, | 
|  | { } | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(i2c, adv7842_id); | 
|  |  | 
|  | /* ----------------------------------------------------------------------- */ | 
|  |  | 
|  | static struct i2c_driver adv7842_driver = { | 
|  | .driver = { | 
|  | .name = "adv7842", | 
|  | }, | 
|  | .probe = adv7842_probe, | 
|  | .remove = adv7842_remove, | 
|  | .id_table = adv7842_id, | 
|  | }; | 
|  |  | 
|  | module_i2c_driver(adv7842_driver); |