blob: 0abd7bf17568bdf5a040fe9f8918aea092fbbbca [file] [log] [blame]
/*
* pm9g45.dts - Device Tree file for Ronetix pm9g45 board
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2.
*/
/dts-v1/;
#include "at91sam9g45.dtsi"
/ {
model = "Ronetix pm9g45";
compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
chosen {
bootargs = "console=ttyS0,115200";
};
memory {
reg = <0x70000000 0x8000000>;
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
dbgu: serial@ffffee00 {
status = "okay";
};
pinctrl@fffff200 {
board {
pinctrl_board_nand: nand0-board {
atmel,pins =
<AT91_PIOD 3 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PD3 gpio RDY pin pull_up*/
AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PC14 gpio enable pin pull_up */
};
};
mmc {
pinctrl_board_mmc: mmc0-board {
atmel,pins =
<AT91_PIOD 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD6 gpio CD pin pull_up and deglitch */
};
};
};
mmc0: mmc@fff80000 {
pinctrl-0 = <
&pinctrl_board_mmc
&pinctrl_mmc0_slot0_clk_cmd_dat0
&pinctrl_mmc0_slot0_dat1_3>;
status = "okay";
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioD 6 GPIO_ACTIVE_HIGH>;
};
};
macb0: ethernet@fffbc000 {
phy-mode = "rmii";
status = "okay";
};
};
nand0: nand@40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
nand-on-flash-bbt;
pinctrl-0 = <&pinctrl_board_nand>;
gpios = <&pioD 3 GPIO_ACTIVE_HIGH
&pioC 14 GPIO_ACTIVE_HIGH
0
>;
status = "okay";
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x20000>;
};
barebox@20000 {
label = "barebox";
reg = <0x20000 0x40000>;
};
bareboxenv@60000 {
label = "bareboxenv";
reg = <0x60000 0x1A0000>;
};
kernel@200000 {
label = "bareboxenv2";
reg = <0x200000 0x300000>;
};
kernel@500000 {
label = "root";
reg = <0x500000 0x400000>;
};
data@900000 {
label = "data";
reg = <0x900000 0x8340000>;
};
};
usb0: ohci@00700000 {
status = "okay";
num-ports = <2>;
};
usb1: ehci@00800000 {
status = "okay";
};
};
leds {
compatible = "gpio-leds";
led0 {
label = "led0";
gpios = <&pioD 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "nand-disk";
};
led1 {
label = "led1";
gpios = <&pioD 31 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
right {
label = "SW4";
gpios = <&pioE 7 GPIO_ACTIVE_LOW>;
linux,code = <106>;
};
up {
label = "SW3";
gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
linux,code = <103>;
};
};
};