config.mk

export

## NOTE
## Make sure to have each variable declaration start
## in the first column, no whitespace allowed.

ifeq ($(wildcard $(KLIB_BUILD)/.config),)
# These will be ignored by compat autoconf
 CONFIG_PCI=y
 CONFIG_USB=y
 CONFIG_PCMCIA=y
else
include $(KLIB_BUILD)/.config
endif

# Wireless subsystem stuff
CONFIG_MAC80211=m

CONFIG_MAC80211_RC_DEFAULT=pid
CONFIG_MAC80211_RC_PID=y

# enable mesh networking too
CONFIG_MAC80211_MESH=y

CONFIG_CFG80211=m
CONFIG_NL80211=y

# PCI Drivers
ifneq ($(CONFIG_PCI),)

CONFIG_ATH5K=m
CONFIG_ATH5K_DEBUG=n
CONFIG_IWLCORE=m
CONFIG_IWL3945=m
CONFIG_IWL4965=m
CONFIG_IWL4965_HT=y
CONFIG_B43=m
# B43 uses PCMCIA only for Compact Flash. The Cardbus cards uses PCI
# Example, bcm4318:
# http://www.multicap.biz/wireless-lan/indoor-wlan-hardware/sdc-cf10g-80211g-compact-flash-module
CONFIG_B43_PCMCIA=y
CONFIG_B43_DMA=y
CONFIG_B43_PIO=y
CONFIG_B43_DMA_AND_PIO_MODE=y
CONFIG_B43_PCI_AUTOSELECT=y
CONFIG_B43_PCICORE_AUTOSELECT=y
#CONFIG_B43_RFKILL=n
CONFIG_B43_LEDS=y
# CONFIG_B43_DEBUG is not set

CONFIG_B43LEGACY=m
CONFIG_B43LEGACY_PCI_AUTOSELECT=y
CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y
CONFIG_B43LEGACY_DMA=y
CONFIG_B43LEGACY_PIO=y
CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y

# The Intel ipws
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW2200_RADIOTAP=y
CONFIG_IPW2200_PROMISCUOUS=y
# The above enables use a second interface prefixed 'rtap'.
#           Example usage:
#
# % modprobe ipw2200 rtap_iface=1
# % ifconfig rtap0 up
# % tethereal -i rtap0
#
# If you do not specify 'rtap_iface=1' as a module parameter then
# the rtap interface will not be created and you will need to turn
# it on via sysfs:
#
# % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
CONFIG_IPW2200_QOS=y

NEED_IEEE80211=y

CONFIG_P54_PCI=m

CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

CONFIG_RTL8180=m
CONFIG_ADM8211=m

CONFIG_RT2X00_LIB_PCI=m
CONFIG_RT2400PCI=m
CONFIG_RT2500PCI=m
NEED_RT2X00=y

# Two rt2x00 drivers require firmware: rt61pci and rt73usb. They depend on
# CRC to check the firmware. We check here first for the PCI
# driver as we're in the PCI section.
ifneq ($(CONFIG_CRC_ITU_T),)
CONFIG_RT61PCI=m
NEED_RT2X00_FIRMWARE=y
endif

endif
## end of PCI

# This is required for some cards
CONFIG_EEPROM_93CX6=m

# USB Drivers
ifneq ($(CONFIG_USB),)
CONFIG_ZD1211RW=m

# support for USB Wireless devices using Atmel at76c503,
# at76c505 or at76c505a chips.
CONFIG_USB_ATMEL=m

# Stuff here things which depend on kernel versions for USB
ifeq ($(shell test -e $(KLIB_BUILD)/Makefile && echo yes),yes)
ifeq ($(shell test $(shell sed 's/^SUBLEVEL = //;t;d' < $(KLIB_BUILD)/Makefile) -gt 21 && echo yes),yes)

# Sorry, rndis_wlan uses cancel_work_sync which is new and can't be done in compat...

# Wireless RNDIS USB support (RTL8185 802.11g) A-Link WL54PC
# All of these devices are based on Broadcom 4320 chip which
# is only wireless RNDIS chip known to date.
# Note: this depends on CONFIG_USB_NET_RNDIS_HOST and CONFIG_USB_NET_CDCETHER
# it also requires a new RNDIS_HOST module which we add
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_RNDIS_WLAN=m

endif
endif

CONFIG_P54_USB=m
CONFIG_RTL8187=m

# RT2500USB does not require firmware
CONFIG_RT2500USB=m
CONFIG_RT2X00_LIB_USB=m
NEED_RT2X00=y
# RT73USB requires firmware
ifneq ($(CONFIG_CRC_ITU_T),)
CONFIG_RT73USB=m
NEED_RT2X00_FIRMWARE=y
endif

endif # end of USB driver list

# Common rt2x00 requirements
ifeq ($(NEED_RT2X00),y)
CONFIG_RT2X00=m
CONFIG_RT2X00_LIB=m
# CONFIG_RT2X00_LIB_DEBUGFS is not set
# CONFIG_RT2X00_DEBUG is not set
endif

ifeq ($(NEED_RT2X00_FIRMWARE),y)
CONFIG_RT2X00_LIB_FIRMWARE=y
endif

# p54
CONFIG_P54_COMMON=m

# Sonics Silicon Backplane
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=m
CONFIG_SSB_SPROM=y

ifneq ($(CONFIG_PCMCIA),)
CONFIG_SSB_PCMCIAHOST=y
endif

# These two are for mips
CONFIG_SSB_DRIVER_MIPS=n
CONFIG_SSB_PCICORE_HOSTMODE=n
# CONFIG_SSB_DEBUG is not set
# CONFIG_SSB_DRIVER_EXTIF=y

ifneq ($(CONFIG_USB),)
CONFIG_LIBERTAS_USB=m
NEED_LIBERTAS=y
endif
ifneq ($(CONFIG_PCMCIA),)
CONFIG_LIBERTAS_CS=m
NEED_LIBERTAS=y
endif
ifeq ($(NEED_LIBERTAS),y)
CONFIG_LIBERTAS=m
# Libertas uses the old stack but not fully, it will soon 
# be cleaned.
NEED_IEEE80211=y
endif

ifeq ($(NEED_IEEE80211),y)
# Old ieee80211 "stack"
# Note: old softmac is scheduled for removal so we
# ignore that stuff
CONFIG_IEEE80211=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_SOFTMAC=n
endif