|  | // SPDX-License-Identifier: GPL-2.0 | 
|  | /* | 
|  | * Driver for Future Domain TMC-16x0 and TMC-3260 SCSI host adapters | 
|  | * Copyright 2019 Ondrej Zary | 
|  | * | 
|  | * Original driver by | 
|  | * Rickard E. Faith, faith@cs.unc.edu | 
|  | * | 
|  | * Future Domain BIOS versions supported for autodetect: | 
|  | *    2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61 | 
|  | * Chips supported: | 
|  | *    TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70 | 
|  | * Boards supported: | 
|  | *    Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX | 
|  | *    Future Domain TMC-3260 (PCI) | 
|  | *    Quantum ISA-200S, ISA-250MG | 
|  | *    Adaptec AHA-2920A (PCI) [BUT *NOT* AHA-2920C -- use aic7xxx instead] | 
|  | *    IBM ? | 
|  | * | 
|  | * NOTE: | 
|  | * | 
|  | * The Adaptec AHA-2920C has an Adaptec AIC-7850 chip on it. | 
|  | * Use the aic7xxx driver for this board. | 
|  | * | 
|  | * The Adaptec AHA-2920A has a Future Domain chip on it, so this is the right | 
|  | * driver for that card.  Unfortunately, the boxes will probably just say | 
|  | * "2920", so you'll have to look on the card for a Future Domain logo, or a | 
|  | * letter after the 2920. | 
|  | * | 
|  | * If you have a TMC-8xx or TMC-9xx board, then this is not the driver for | 
|  | * your board. | 
|  | * | 
|  | * DESCRIPTION: | 
|  | * | 
|  | * This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680 | 
|  | * TMC-1650/1670, and TMC-3260 SCSI host adapters.  The 1650 and 1670 have a | 
|  | * 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin | 
|  | * high-density external connector.  The 1670 and 1680 have floppy disk | 
|  | * controllers built in.  The TMC-3260 is a PCI bus card. | 
|  | * | 
|  | * Future Domain's older boards are based on the TMC-1800 chip, and this | 
|  | * driver was originally written for a TMC-1680 board with the TMC-1800 chip. | 
|  | * More recently, boards are being produced with the TMC-18C50 and TMC-18C30 | 
|  | * chips. | 
|  | * | 
|  | * Please note that the drive ordering that Future Domain implemented in BIOS | 
|  | * versions 3.4 and 3.5 is the opposite of the order (currently) used by the | 
|  | * rest of the SCSI industry. | 
|  | * | 
|  | * | 
|  | * REFERENCES USED: | 
|  | * | 
|  | * "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation, | 
|  | * 1990. | 
|  | * | 
|  | * "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain | 
|  | * Corporation, January 1992. | 
|  | * | 
|  | * "LXT SCSI Products: Specifications and OEM Technical Manual (Revision | 
|  | * B/September 1991)", Maxtor Corporation, 1991. | 
|  | * | 
|  | * "7213S product Manual (Revision P3)", Maxtor Corporation, 1992. | 
|  | * | 
|  | * "Draft Proposed American National Standard: Small Computer System | 
|  | * Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109, | 
|  | * revision 10h, October 17, 1991) | 
|  | * | 
|  | * Private communications, Drew Eckhardt (drew@cs.colorado.edu) and Eric | 
|  | * Youngdale (ericy@cais.com), 1992. | 
|  | * | 
|  | * Private communication, Tuong Le (Future Domain Engineering department), | 
|  | * 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and | 
|  | * TMC-18C30 detection.) | 
|  | * | 
|  | * Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page | 
|  | * 60 (2.39: Disk Partition Table Layout). | 
|  | * | 
|  | * "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page | 
|  | * 6-1. | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/pci.h> | 
|  | #include <linux/workqueue.h> | 
|  | #include <scsi/scsicam.h> | 
|  | #include <scsi/scsi_cmnd.h> | 
|  | #include <scsi/scsi_device.h> | 
|  | #include <scsi/scsi_host.h> | 
|  | #include "fdomain.h" | 
|  |  | 
|  | /* | 
|  | * FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the | 
|  | * 18C30 chip have a 2k cache).  When this many 512 byte blocks are filled by | 
|  | * the SCSI device, an interrupt will be raised.  Therefore, this could be as | 
|  | * low as 0, or as high as 16.  Note, however, that values which are too high | 
|  | * or too low seem to prevent any interrupts from occurring, and thereby lock | 
|  | * up the machine. | 
|  | */ | 
|  | #define FIFO_COUNT	2	/* Number of 512 byte blocks before INTR */ | 
|  | #define PARITY_MASK	ACTL_PAREN	/* Parity enabled, 0 = disabled */ | 
|  |  | 
|  | enum chip_type { | 
|  | unknown		= 0x00, | 
|  | tmc1800		= 0x01, | 
|  | tmc18c50	= 0x02, | 
|  | tmc18c30	= 0x03, | 
|  | }; | 
|  |  | 
|  | struct fdomain { | 
|  | int base; | 
|  | struct scsi_cmnd *cur_cmd; | 
|  | enum chip_type chip; | 
|  | struct work_struct work; | 
|  | }; | 
|  |  | 
|  | static inline void fdomain_make_bus_idle(struct fdomain *fd) | 
|  | { | 
|  | outb(0, fd->base + REG_BCTL); | 
|  | outb(0, fd->base + REG_MCTL); | 
|  | if (fd->chip == tmc18c50 || fd->chip == tmc18c30) | 
|  | /* Clear forced intr. */ | 
|  | outb(ACTL_RESET | ACTL_CLRFIRQ | PARITY_MASK, | 
|  | fd->base + REG_ACTL); | 
|  | else | 
|  | outb(ACTL_RESET | PARITY_MASK, fd->base + REG_ACTL); | 
|  | } | 
|  |  | 
|  | static enum chip_type fdomain_identify(int port) | 
|  | { | 
|  | u16 id = inb(port + REG_ID_LSB) | inb(port + REG_ID_MSB) << 8; | 
|  |  | 
|  | switch (id) { | 
|  | case 0x6127: | 
|  | return tmc1800; | 
|  | case 0x60e9: /* 18c50 or 18c30 */ | 
|  | break; | 
|  | default: | 
|  | return unknown; | 
|  | } | 
|  |  | 
|  | /* Try to toggle 32-bit mode. This only works on an 18c30 chip. */ | 
|  | outb(CFG2_32BIT, port + REG_CFG2); | 
|  | if ((inb(port + REG_CFG2) & CFG2_32BIT)) { | 
|  | outb(0, port + REG_CFG2); | 
|  | if ((inb(port + REG_CFG2) & CFG2_32BIT) == 0) | 
|  | return tmc18c30; | 
|  | } | 
|  | /* If that failed, we are an 18c50. */ | 
|  | return tmc18c50; | 
|  | } | 
|  |  | 
|  | static int fdomain_test_loopback(int base) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < 255; i++) { | 
|  | outb(i, base + REG_LOOPBACK); | 
|  | if (inb(base + REG_LOOPBACK) != i) | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void fdomain_reset(int base) | 
|  | { | 
|  | outb(BCTL_RST, base + REG_BCTL); | 
|  | mdelay(20); | 
|  | outb(0, base + REG_BCTL); | 
|  | mdelay(1150); | 
|  | outb(0, base + REG_MCTL); | 
|  | outb(PARITY_MASK, base + REG_ACTL); | 
|  | } | 
|  |  | 
|  | static int fdomain_select(struct Scsi_Host *sh, int target) | 
|  | { | 
|  | int status; | 
|  | unsigned long timeout; | 
|  | struct fdomain *fd = shost_priv(sh); | 
|  |  | 
|  | outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL); | 
|  | outb(BIT(sh->this_id) | BIT(target), fd->base + REG_SCSI_DATA_NOACK); | 
|  |  | 
|  | /* Stop arbitration and enable parity */ | 
|  | outb(PARITY_MASK, fd->base + REG_ACTL); | 
|  |  | 
|  | timeout = 350;	/* 350 msec */ | 
|  |  | 
|  | do { | 
|  | status = inb(fd->base + REG_BSTAT); | 
|  | if (status & BSTAT_BSY) { | 
|  | /* Enable SCSI Bus */ | 
|  | /* (on error, should make bus idle with 0) */ | 
|  | outb(BCTL_BUSEN, fd->base + REG_BCTL); | 
|  | return 0; | 
|  | } | 
|  | mdelay(1); | 
|  | } while (--timeout); | 
|  | fdomain_make_bus_idle(fd); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static void fdomain_finish_cmd(struct fdomain *fd, int result) | 
|  | { | 
|  | outb(0, fd->base + REG_ICTL); | 
|  | fdomain_make_bus_idle(fd); | 
|  | fd->cur_cmd->result = result; | 
|  | fd->cur_cmd->scsi_done(fd->cur_cmd); | 
|  | fd->cur_cmd = NULL; | 
|  | } | 
|  |  | 
|  | static void fdomain_read_data(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct fdomain *fd = shost_priv(cmd->device->host); | 
|  | unsigned char *virt, *ptr; | 
|  | size_t offset, len; | 
|  |  | 
|  | while ((len = inw(fd->base + REG_FIFO_COUNT)) > 0) { | 
|  | offset = scsi_bufflen(cmd) - scsi_get_resid(cmd); | 
|  | virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd), | 
|  | &offset, &len); | 
|  | ptr = virt + offset; | 
|  | if (len & 1) | 
|  | *ptr++ = inb(fd->base + REG_FIFO); | 
|  | if (len > 1) | 
|  | insw(fd->base + REG_FIFO, ptr, len >> 1); | 
|  | scsi_set_resid(cmd, scsi_get_resid(cmd) - len); | 
|  | scsi_kunmap_atomic_sg(virt); | 
|  | } | 
|  | } | 
|  |  | 
|  | static void fdomain_write_data(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct fdomain *fd = shost_priv(cmd->device->host); | 
|  | /* 8k FIFO for pre-tmc18c30 chips, 2k FIFO for tmc18c30 */ | 
|  | int FIFO_Size = fd->chip == tmc18c30 ? 0x800 : 0x2000; | 
|  | unsigned char *virt, *ptr; | 
|  | size_t offset, len; | 
|  |  | 
|  | while ((len = FIFO_Size - inw(fd->base + REG_FIFO_COUNT)) > 512) { | 
|  | offset = scsi_bufflen(cmd) - scsi_get_resid(cmd); | 
|  | if (len + offset > scsi_bufflen(cmd)) { | 
|  | len = scsi_bufflen(cmd) - offset; | 
|  | if (len == 0) | 
|  | break; | 
|  | } | 
|  | virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd), | 
|  | &offset, &len); | 
|  | ptr = virt + offset; | 
|  | if (len & 1) | 
|  | outb(*ptr++, fd->base + REG_FIFO); | 
|  | if (len > 1) | 
|  | outsw(fd->base + REG_FIFO, ptr, len >> 1); | 
|  | scsi_set_resid(cmd, scsi_get_resid(cmd) - len); | 
|  | scsi_kunmap_atomic_sg(virt); | 
|  | } | 
|  | } | 
|  |  | 
|  | static void fdomain_work(struct work_struct *work) | 
|  | { | 
|  | struct fdomain *fd = container_of(work, struct fdomain, work); | 
|  | struct Scsi_Host *sh = container_of((void *)fd, struct Scsi_Host, | 
|  | hostdata); | 
|  | struct scsi_cmnd *cmd = fd->cur_cmd; | 
|  | unsigned long flags; | 
|  | int status; | 
|  | int done = 0; | 
|  |  | 
|  | spin_lock_irqsave(sh->host_lock, flags); | 
|  |  | 
|  | if (cmd->SCp.phase & in_arbitration) { | 
|  | status = inb(fd->base + REG_ASTAT); | 
|  | if (!(status & ASTAT_ARB)) { | 
|  | fdomain_finish_cmd(fd, DID_BUS_BUSY << 16); | 
|  | goto out; | 
|  | } | 
|  | cmd->SCp.phase = in_selection; | 
|  |  | 
|  | outb(ICTL_SEL | FIFO_COUNT, fd->base + REG_ICTL); | 
|  | outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL); | 
|  | outb(BIT(cmd->device->host->this_id) | BIT(scmd_id(cmd)), | 
|  | fd->base + REG_SCSI_DATA_NOACK); | 
|  | /* Stop arbitration and enable parity */ | 
|  | outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL); | 
|  | goto out; | 
|  | } else if (cmd->SCp.phase & in_selection) { | 
|  | status = inb(fd->base + REG_BSTAT); | 
|  | if (!(status & BSTAT_BSY)) { | 
|  | /* Try again, for slow devices */ | 
|  | if (fdomain_select(cmd->device->host, scmd_id(cmd))) { | 
|  | fdomain_finish_cmd(fd, DID_NO_CONNECT << 16); | 
|  | goto out; | 
|  | } | 
|  | /* Stop arbitration and enable parity */ | 
|  | outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL); | 
|  | } | 
|  | cmd->SCp.phase = in_other; | 
|  | outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT, fd->base + REG_ICTL); | 
|  | outb(BCTL_BUSEN, fd->base + REG_BCTL); | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | /* cur_cmd->SCp.phase == in_other: this is the body of the routine */ | 
|  | status = inb(fd->base + REG_BSTAT); | 
|  |  | 
|  | if (status & BSTAT_REQ) { | 
|  | switch (status & (BSTAT_MSG | BSTAT_CMD | BSTAT_IO)) { | 
|  | case BSTAT_CMD:	/* COMMAND OUT */ | 
|  | outb(cmd->cmnd[cmd->SCp.sent_command++], | 
|  | fd->base + REG_SCSI_DATA); | 
|  | break; | 
|  | case 0:	/* DATA OUT -- tmc18c50/tmc18c30 only */ | 
|  | if (fd->chip != tmc1800 && !cmd->SCp.have_data_in) { | 
|  | cmd->SCp.have_data_in = -1; | 
|  | outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN | | 
|  | PARITY_MASK, fd->base + REG_ACTL); | 
|  | } | 
|  | break; | 
|  | case BSTAT_IO:	/* DATA IN -- tmc18c50/tmc18c30 only */ | 
|  | if (fd->chip != tmc1800 && !cmd->SCp.have_data_in) { | 
|  | cmd->SCp.have_data_in = 1; | 
|  | outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK, | 
|  | fd->base + REG_ACTL); | 
|  | } | 
|  | break; | 
|  | case BSTAT_CMD | BSTAT_IO:	/* STATUS IN */ | 
|  | cmd->SCp.Status = inb(fd->base + REG_SCSI_DATA); | 
|  | break; | 
|  | case BSTAT_MSG | BSTAT_CMD:	/* MESSAGE OUT */ | 
|  | outb(MESSAGE_REJECT, fd->base + REG_SCSI_DATA); | 
|  | break; | 
|  | case BSTAT_MSG | BSTAT_CMD | BSTAT_IO:	/* MESSAGE IN */ | 
|  | cmd->SCp.Message = inb(fd->base + REG_SCSI_DATA); | 
|  | if (!cmd->SCp.Message) | 
|  | ++done; | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (fd->chip == tmc1800 && !cmd->SCp.have_data_in && | 
|  | cmd->SCp.sent_command >= cmd->cmd_len) { | 
|  | if (cmd->sc_data_direction == DMA_TO_DEVICE) { | 
|  | cmd->SCp.have_data_in = -1; | 
|  | outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN | | 
|  | PARITY_MASK, fd->base + REG_ACTL); | 
|  | } else { | 
|  | cmd->SCp.have_data_in = 1; | 
|  | outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK, | 
|  | fd->base + REG_ACTL); | 
|  | } | 
|  | } | 
|  |  | 
|  | if (cmd->SCp.have_data_in == -1) /* DATA OUT */ | 
|  | fdomain_write_data(cmd); | 
|  |  | 
|  | if (cmd->SCp.have_data_in == 1) /* DATA IN */ | 
|  | fdomain_read_data(cmd); | 
|  |  | 
|  | if (done) { | 
|  | fdomain_finish_cmd(fd, (cmd->SCp.Status & 0xff) | | 
|  | ((cmd->SCp.Message & 0xff) << 8) | | 
|  | (DID_OK << 16)); | 
|  | } else { | 
|  | if (cmd->SCp.phase & disconnect) { | 
|  | outb(ICTL_FIFO | ICTL_SEL | ICTL_REQ | FIFO_COUNT, | 
|  | fd->base + REG_ICTL); | 
|  | outb(0, fd->base + REG_BCTL); | 
|  | } else | 
|  | outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT, | 
|  | fd->base + REG_ICTL); | 
|  | } | 
|  | out: | 
|  | spin_unlock_irqrestore(sh->host_lock, flags); | 
|  | } | 
|  |  | 
|  | static irqreturn_t fdomain_irq(int irq, void *dev_id) | 
|  | { | 
|  | struct fdomain *fd = dev_id; | 
|  |  | 
|  | /* Is it our IRQ? */ | 
|  | if ((inb(fd->base + REG_ASTAT) & ASTAT_IRQ) == 0) | 
|  | return IRQ_NONE; | 
|  |  | 
|  | outb(0, fd->base + REG_ICTL); | 
|  |  | 
|  | /* We usually have one spurious interrupt after each command. */ | 
|  | if (!fd->cur_cmd)	/* Spurious interrupt */ | 
|  | return IRQ_NONE; | 
|  |  | 
|  | schedule_work(&fd->work); | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static int fdomain_queue(struct Scsi_Host *sh, struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct fdomain *fd = shost_priv(cmd->device->host); | 
|  | unsigned long flags; | 
|  |  | 
|  | cmd->SCp.Status		= 0; | 
|  | cmd->SCp.Message	= 0; | 
|  | cmd->SCp.have_data_in	= 0; | 
|  | cmd->SCp.sent_command	= 0; | 
|  | cmd->SCp.phase		= in_arbitration; | 
|  | scsi_set_resid(cmd, scsi_bufflen(cmd)); | 
|  |  | 
|  | spin_lock_irqsave(sh->host_lock, flags); | 
|  |  | 
|  | fd->cur_cmd = cmd; | 
|  |  | 
|  | fdomain_make_bus_idle(fd); | 
|  |  | 
|  | /* Start arbitration */ | 
|  | outb(0, fd->base + REG_ICTL); | 
|  | outb(0, fd->base + REG_BCTL);	/* Disable data drivers */ | 
|  | /* Set our id bit */ | 
|  | outb(BIT(cmd->device->host->this_id), fd->base + REG_SCSI_DATA_NOACK); | 
|  | outb(ICTL_ARB, fd->base + REG_ICTL); | 
|  | /* Start arbitration */ | 
|  | outb(ACTL_ARB | ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL); | 
|  |  | 
|  | spin_unlock_irqrestore(sh->host_lock, flags); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int fdomain_abort(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct Scsi_Host *sh = cmd->device->host; | 
|  | struct fdomain *fd = shost_priv(sh); | 
|  | unsigned long flags; | 
|  |  | 
|  | if (!fd->cur_cmd) | 
|  | return FAILED; | 
|  |  | 
|  | spin_lock_irqsave(sh->host_lock, flags); | 
|  |  | 
|  | fdomain_make_bus_idle(fd); | 
|  | fd->cur_cmd->SCp.phase |= aborted; | 
|  | fd->cur_cmd->result = DID_ABORT << 16; | 
|  |  | 
|  | /* Aborts are not done well. . . */ | 
|  | fdomain_finish_cmd(fd, DID_ABORT << 16); | 
|  | spin_unlock_irqrestore(sh->host_lock, flags); | 
|  | return SUCCESS; | 
|  | } | 
|  |  | 
|  | static int fdomain_host_reset(struct scsi_cmnd *cmd) | 
|  | { | 
|  | struct Scsi_Host *sh = cmd->device->host; | 
|  | struct fdomain *fd = shost_priv(sh); | 
|  | unsigned long flags; | 
|  |  | 
|  | spin_lock_irqsave(sh->host_lock, flags); | 
|  | fdomain_reset(fd->base); | 
|  | spin_unlock_irqrestore(sh->host_lock, flags); | 
|  | return SUCCESS; | 
|  | } | 
|  |  | 
|  | static int fdomain_biosparam(struct scsi_device *sdev, | 
|  | struct block_device *bdev,	sector_t capacity, | 
|  | int geom[]) | 
|  | { | 
|  | unsigned char *p = scsi_bios_ptable(bdev); | 
|  |  | 
|  | if (p && p[65] == 0xaa && p[64] == 0x55 /* Partition table valid */ | 
|  | && p[4]) {	 /* Partition type */ | 
|  | geom[0] = p[5] + 1;	/* heads */ | 
|  | geom[1] = p[6] & 0x3f;	/* sectors */ | 
|  | } else { | 
|  | if (capacity >= 0x7e0000) { | 
|  | geom[0] = 255;	/* heads */ | 
|  | geom[1] = 63;	/* sectors */ | 
|  | } else if (capacity >= 0x200000) { | 
|  | geom[0] = 128;	/* heads */ | 
|  | geom[1] = 63;	/* sectors */ | 
|  | } else { | 
|  | geom[0] = 64;	/* heads */ | 
|  | geom[1] = 32;	/* sectors */ | 
|  | } | 
|  | } | 
|  | geom[2] = sector_div(capacity, geom[0] * geom[1]); | 
|  | kfree(p); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct scsi_host_template fdomain_template = { | 
|  | .module			= THIS_MODULE, | 
|  | .name			= "Future Domain TMC-16x0", | 
|  | .proc_name		= "fdomain", | 
|  | .queuecommand		= fdomain_queue, | 
|  | .eh_abort_handler	= fdomain_abort, | 
|  | .eh_host_reset_handler	= fdomain_host_reset, | 
|  | .bios_param		= fdomain_biosparam, | 
|  | .can_queue		= 1, | 
|  | .this_id		= 7, | 
|  | .sg_tablesize		= 64, | 
|  | .dma_boundary		= PAGE_SIZE - 1, | 
|  | }; | 
|  |  | 
|  | struct Scsi_Host *fdomain_create(int base, int irq, int this_id, | 
|  | struct device *dev) | 
|  | { | 
|  | struct Scsi_Host *sh; | 
|  | struct fdomain *fd; | 
|  | enum chip_type chip; | 
|  | static const char * const chip_names[] = { | 
|  | "Unknown", "TMC-1800", "TMC-18C50", "TMC-18C30" | 
|  | }; | 
|  | unsigned long irq_flags = 0; | 
|  |  | 
|  | chip = fdomain_identify(base); | 
|  | if (!chip) | 
|  | return NULL; | 
|  |  | 
|  | fdomain_reset(base); | 
|  |  | 
|  | if (fdomain_test_loopback(base)) | 
|  | return NULL; | 
|  |  | 
|  | if (!irq) { | 
|  | dev_err(dev, "card has no IRQ assigned"); | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | sh = scsi_host_alloc(&fdomain_template, sizeof(struct fdomain)); | 
|  | if (!sh) | 
|  | return NULL; | 
|  |  | 
|  | if (this_id) | 
|  | sh->this_id = this_id & 0x07; | 
|  |  | 
|  | sh->irq = irq; | 
|  | sh->io_port = base; | 
|  | sh->n_io_port = FDOMAIN_REGION_SIZE; | 
|  |  | 
|  | fd = shost_priv(sh); | 
|  | fd->base = base; | 
|  | fd->chip = chip; | 
|  | INIT_WORK(&fd->work, fdomain_work); | 
|  |  | 
|  | if (dev_is_pci(dev) || !strcmp(dev->bus->name, "pcmcia")) | 
|  | irq_flags = IRQF_SHARED; | 
|  |  | 
|  | if (request_irq(irq, fdomain_irq, irq_flags, "fdomain", fd)) | 
|  | goto fail_put; | 
|  |  | 
|  | shost_printk(KERN_INFO, sh, "%s chip at 0x%x irq %d SCSI ID %d\n", | 
|  | dev_is_pci(dev) ? "TMC-36C70 (PCI bus)" : chip_names[chip], | 
|  | base, irq, sh->this_id); | 
|  |  | 
|  | if (scsi_add_host(sh, dev)) | 
|  | goto fail_free_irq; | 
|  |  | 
|  | scsi_scan_host(sh); | 
|  |  | 
|  | return sh; | 
|  |  | 
|  | fail_free_irq: | 
|  | free_irq(irq, fd); | 
|  | fail_put: | 
|  | scsi_host_put(sh); | 
|  | return NULL; | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(fdomain_create); | 
|  |  | 
|  | int fdomain_destroy(struct Scsi_Host *sh) | 
|  | { | 
|  | struct fdomain *fd = shost_priv(sh); | 
|  |  | 
|  | cancel_work_sync(&fd->work); | 
|  | scsi_remove_host(sh); | 
|  | if (sh->irq) | 
|  | free_irq(sh->irq, fd); | 
|  | scsi_host_put(sh); | 
|  | return 0; | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(fdomain_destroy); | 
|  |  | 
|  | #ifdef CONFIG_PM_SLEEP | 
|  | static int fdomain_resume(struct device *dev) | 
|  | { | 
|  | struct fdomain *fd = shost_priv(dev_get_drvdata(dev)); | 
|  |  | 
|  | fdomain_reset(fd->base); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static SIMPLE_DEV_PM_OPS(fdomain_pm_ops, NULL, fdomain_resume); | 
|  | #endif /* CONFIG_PM_SLEEP */ | 
|  |  | 
|  | MODULE_AUTHOR("Ondrej Zary, Rickard E. Faith"); | 
|  | MODULE_DESCRIPTION("Future Domain TMC-16x0/TMC-3260 SCSI driver"); | 
|  | MODULE_LICENSE("GPL"); |