blob: 1e173f6285c73b76b2e6ab41daed7681406c5d15 [file] [log] [blame]
/*
* x86 FPU boot time init code:
*/
#include <asm/fpu/internal.h>
#include <asm/tlbflush.h>
#include <linux/sched.h>
/*
* Initialize the TS bit in CR0 according to the style of context-switches
* we are using:
*/
static void fpu__init_cpu_ctx_switch(void)
{
if (!cpu_has_eager_fpu)
stts();
else
clts();
}
/*
* Initialize the registers found in all CPUs, CR0 and CR4:
*/
static void fpu__init_cpu_generic(void)
{
unsigned long cr0;
unsigned long cr4_mask = 0;
if (cpu_has_fxsr)
cr4_mask |= X86_CR4_OSFXSR;
if (cpu_has_xmm)
cr4_mask |= X86_CR4_OSXMMEXCPT;
if (cr4_mask)
cr4_set_bits(cr4_mask);
cr0 = read_cr0();
cr0 &= ~(X86_CR0_TS|X86_CR0_EM); /* clear TS and EM */
if (!cpu_has_fpu)
cr0 |= X86_CR0_EM;
write_cr0(cr0);
/* Flush out any pending x87 state: */
asm volatile ("fninit");
}
/*
* Enable all supported FPU features. Called when a CPU is brought online:
*/
void fpu__init_cpu(void)
{
fpu__init_cpu_generic();
fpu__init_cpu_xstate();
fpu__init_cpu_ctx_switch();
}
/*
* The earliest FPU detection code.
*
* Set the X86_FEATURE_FPU CPU-capability bit based on
* trying to execute an actual sequence of FPU instructions:
*/
static void fpu__init_system_early_generic(struct cpuinfo_x86 *c)
{
unsigned long cr0;
u16 fsw, fcw;
fsw = fcw = 0xffff;
cr0 = read_cr0();
cr0 &= ~(X86_CR0_TS | X86_CR0_EM);
write_cr0(cr0);
asm volatile("fninit ; fnstsw %0 ; fnstcw %1"
: "+m" (fsw), "+m" (fcw));
if (fsw == 0 && (fcw & 0x103f) == 0x003f)
set_cpu_cap(c, X86_FEATURE_FPU);
else
clear_cpu_cap(c, X86_FEATURE_FPU);
#ifndef CONFIG_MATH_EMULATION
if (!cpu_has_fpu) {
pr_emerg("x86/fpu: Giving up, no FPU found and no math emulation present\n");
for (;;)
asm volatile("hlt");
}
#endif
}
/*
* Boot time FPU feature detection code:
*/
unsigned int mxcsr_feature_mask __read_mostly = 0xffffffffu;
static void __init fpu__init_system_mxcsr(void)
{
unsigned int mask = 0;
if (cpu_has_fxsr) {
/* Static because GCC does not get 16-byte stack alignment right: */
static struct fxregs_state fxregs __initdata;
asm volatile("fxsave %0" : "+m" (fxregs));
mask = fxregs.mxcsr_mask;
/*
* If zero then use the default features mask,
* which has all features set, except the
* denormals-are-zero feature bit:
*/
if (mask == 0)
mask = 0x0000ffbf;
}
mxcsr_feature_mask &= mask;
}
/*
* Once per bootup FPU initialization sequences that will run on most x86 CPUs:
*/
static void __init fpu__init_system_generic(void)
{
/*
* Set up the legacy init FPU context. (xstate init might overwrite this
* with a more modern format, if the CPU supports it.)
*/
fpstate_init_fxstate(&init_fpstate.fxsave);
fpu__init_system_mxcsr();
}
/*
* Size of the FPU context state. All tasks in the system use the
* same context size, regardless of what portion they use.
* This is inherent to the XSAVE architecture which puts all state
* components into a single, continuous memory block:
*/
unsigned int xstate_size;
EXPORT_SYMBOL_GPL(xstate_size);
/* Enforce that 'MEMBER' is the last field of 'TYPE': */
#define CHECK_MEMBER_AT_END_OF(TYPE, MEMBER) \
BUILD_BUG_ON(sizeof(TYPE) != offsetofend(TYPE, MEMBER))
/*
* We append the 'struct fpu' to the task_struct:
*/
static void __init fpu__init_task_struct_size(void)
{
int task_size = sizeof(struct task_struct);
/*
* Subtract off the static size of the register state.
* It potentially has a bunch of padding.
*/
task_size -= sizeof(((struct task_struct *)0)->thread.fpu.state);
/*
* Add back the dynamically-calculated register state
* size.
*/
task_size += xstate_size;
/*
* We dynamically size 'struct fpu', so we require that
* it be at the end of 'thread_struct' and that
* 'thread_struct' be at the end of 'task_struct'. If
* you hit a compile error here, check the structure to
* see if something got added to the end.
*/
CHECK_MEMBER_AT_END_OF(struct fpu, state);
CHECK_MEMBER_AT_END_OF(struct thread_struct, fpu);
CHECK_MEMBER_AT_END_OF(struct task_struct, thread);
arch_task_struct_size = task_size;
}
/*
* Set up the xstate_size based on the legacy FPU context size.
*
* We set this up first, and later it will be overwritten by
* fpu__init_system_xstate() if the CPU knows about xstates.
*/
static void __init fpu__init_system_xstate_size_legacy(void)
{
static int on_boot_cpu = 1;
WARN_ON_FPU(!on_boot_cpu);
on_boot_cpu = 0;
/*
* Note that xstate_size might be overwriten later during
* fpu__init_system_xstate().
*/
if (!cpu_has_fpu) {
/*
* Disable xsave as we do not support it if i387
* emulation is enabled.
*/
setup_clear_cpu_cap(X86_FEATURE_XSAVE);
setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
xstate_size = sizeof(struct swregs_state);
} else {
if (cpu_has_fxsr)
xstate_size = sizeof(struct fxregs_state);
else
xstate_size = sizeof(struct fregs_state);
}
/*
* Quirk: we don't yet handle the XSAVES* instructions
* correctly, as we don't correctly convert between
* standard and compacted format when interfacing
* with user-space - so disable it for now.
*
* The difference is small: with recent CPUs the
* compacted format is only marginally smaller than
* the standard FPU state format.
*
* ( This is easy to backport while we are fixing
* XSAVES* support. )
*/
setup_clear_cpu_cap(X86_FEATURE_XSAVES);
}
/*
* FPU context switching strategies:
*
* Against popular belief, we don't do lazy FPU saves, due to the
* task migration complications it brings on SMP - we only do
* lazy FPU restores.
*
* 'lazy' is the traditional strategy, which is based on setting
* CR0::TS to 1 during context-switch (instead of doing a full
* restore of the FPU state), which causes the first FPU instruction
* after the context switch (whenever it is executed) to fault - at
* which point we lazily restore the FPU state into FPU registers.
*
* Tasks are of course under no obligation to execute FPU instructions,
* so it can easily happen that another context-switch occurs without
* a single FPU instruction being executed. If we eventually switch
* back to the original task (that still owns the FPU) then we have
* not only saved the restores along the way, but we also have the
* FPU ready to be used for the original task.
*
* 'eager' switching is used on modern CPUs, there we switch the FPU
* state during every context switch, regardless of whether the task
* has used FPU instructions in that time slice or not. This is done
* because modern FPU context saving instructions are able to optimize
* state saving and restoration in hardware: they can detect both
* unused and untouched FPU state and optimize accordingly.
*
* [ Note that even in 'lazy' mode we might optimize context switches
* to use 'eager' restores, if we detect that a task is using the FPU
* frequently. See the fpu->counter logic in fpu/internal.h for that. ]
*/
static enum { AUTO, ENABLE, DISABLE } eagerfpu = AUTO;
static int __init eager_fpu_setup(char *s)
{
if (!strcmp(s, "on"))
eagerfpu = ENABLE;
else if (!strcmp(s, "off"))
eagerfpu = DISABLE;
else if (!strcmp(s, "auto"))
eagerfpu = AUTO;
return 1;
}
__setup("eagerfpu=", eager_fpu_setup);
/*
* Pick the FPU context switching strategy:
*/
static void __init fpu__init_system_ctx_switch(void)
{
static bool on_boot_cpu = 1;
WARN_ON_FPU(!on_boot_cpu);
on_boot_cpu = 0;
WARN_ON_FPU(current->thread.fpu.fpstate_active);
current_thread_info()->status = 0;
/* Auto enable eagerfpu for xsaveopt */
if (cpu_has_xsaveopt && eagerfpu != DISABLE)
eagerfpu = ENABLE;
if (xfeatures_mask & XSTATE_EAGER) {
if (eagerfpu == DISABLE) {
pr_err("x86/fpu: eagerfpu switching disabled, disabling the following xstate features: 0x%llx.\n",
xfeatures_mask & XSTATE_EAGER);
xfeatures_mask &= ~XSTATE_EAGER;
} else {
eagerfpu = ENABLE;
}
}
if (eagerfpu == ENABLE)
setup_force_cpu_cap(X86_FEATURE_EAGER_FPU);
printk(KERN_INFO "x86/fpu: Using '%s' FPU context switches.\n", eagerfpu == ENABLE ? "eager" : "lazy");
}
/*
* Called on the boot CPU once per system bootup, to set up the initial
* FPU state that is later cloned into all processes:
*/
void __init fpu__init_system(struct cpuinfo_x86 *c)
{
fpu__init_system_early_generic(c);
/*
* The FPU has to be operational for some of the
* later FPU init activities:
*/
fpu__init_cpu();
/*
* But don't leave CR0::TS set yet, as some of the FPU setup
* methods depend on being able to execute FPU instructions
* that will fault on a set TS, such as the FXSAVE in
* fpu__init_system_mxcsr().
*/
clts();
fpu__init_system_generic();
fpu__init_system_xstate_size_legacy();
fpu__init_system_xstate();
fpu__init_task_struct_size();
fpu__init_system_ctx_switch();
}
/*
* Boot parameter to turn off FPU support and fall back to math-emu:
*/
static int __init no_387(char *s)
{
setup_clear_cpu_cap(X86_FEATURE_FPU);
return 1;
}
__setup("no387", no_387);
/*
* Disable all xstate CPU features:
*/
static int __init x86_noxsave_setup(char *s)
{
if (strlen(s))
return 0;
setup_clear_cpu_cap(X86_FEATURE_XSAVE);
setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
setup_clear_cpu_cap(X86_FEATURE_XSAVEC);
setup_clear_cpu_cap(X86_FEATURE_XSAVES);
setup_clear_cpu_cap(X86_FEATURE_AVX);
setup_clear_cpu_cap(X86_FEATURE_AVX2);
setup_clear_cpu_cap(X86_FEATURE_AVX512F);
setup_clear_cpu_cap(X86_FEATURE_AVX512PF);
setup_clear_cpu_cap(X86_FEATURE_AVX512ER);
setup_clear_cpu_cap(X86_FEATURE_AVX512CD);
setup_clear_cpu_cap(X86_FEATURE_MPX);
return 1;
}
__setup("noxsave", x86_noxsave_setup);
/*
* Disable the XSAVEOPT instruction specifically:
*/
static int __init x86_noxsaveopt_setup(char *s)
{
setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
return 1;
}
__setup("noxsaveopt", x86_noxsaveopt_setup);
/*
* Disable the XSAVES instruction:
*/
static int __init x86_noxsaves_setup(char *s)
{
setup_clear_cpu_cap(X86_FEATURE_XSAVES);
return 1;
}
__setup("noxsaves", x86_noxsaves_setup);
/*
* Disable FX save/restore and SSE support:
*/
static int __init x86_nofxsr_setup(char *s)
{
setup_clear_cpu_cap(X86_FEATURE_FXSR);
setup_clear_cpu_cap(X86_FEATURE_FXSR_OPT);
setup_clear_cpu_cap(X86_FEATURE_XMM);
return 1;
}
__setup("nofxsr", x86_nofxsr_setup);