Merge tag 'drm-fixes-2022-04-08' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Main set of fixes for rc2, mostly amdgpu, but some dma-fence fixups as
well, along with some other misc ones.
dma-fence:
- fix warning about fence containers
- fix logic error in new fence merge code
- handle empty dma_fence_arrays gracefully
bridge:
- Try all possible cases for bridge/panel detection.
bindings:
- Don't require input port for MIPI-DSI, and make width/height mandatory.
fbdev:
- Fix unregistering of framebuffers without device.
nouveau:
- Fix a crash when booting with nouveau on tegra.
amdgpu:
- GFX 10.3.7 fixes
- noretry updates
- VCN fixes
- TMDS fix
- zstate fix for freesync video
- DCN 3.1.5 fix
- Display stack size fix
- Audio fix
- DCN 3.1 pstate fix
- TMZ VCN fix
- APU passthrough fix
- Misc other fixes
- VCN 3.0 fixes
- Misc display fixes
- GC 10.3 golden register fix
- Suspend fix
- SMU 10 fix
amdkfd:
- Error handling fix
- xgmi p2p fix
- HWS VMIDs fix
- Event fix
panel:
- ili9341: Fix optional regulator handling
imx:
- Catch an EDID allocation failure in imx-ldb
- fix a leaked drm display mode on DT parsing error in parallel-display
- properly remove the dw_hdmi bridge in case the component_add fails in dw_hdmi-imx
- fix the IPU clock frequency debug printout in ipu-di"
* tag 'drm-fixes-2022-04-08' of git://anongit.freedesktop.org/drm/drm: (61 commits)
dt-bindings: display: panel: mipi-dbi-spi: Make width-mm/height-mm mandatory
fbdev: Fix unregistering of framebuffers without device
drm/amdgpu/smu10: fix SoC/fclk units in auto mode
drm/amd/display: update dcn315 clock table read
drm/amdgpu/display: change pipe policy for DCN 2.1
drm/amd/display: Add configuration options for AUX wake work around.
drm/amd/display: remove assert for odm transition case
drm/amdgpu: don't use BACO for reset in S3
drm/amd/display: Fix by adding FPU protection for dcn30_internal_validate_bw
drm/amdkfd: Create file descriptor after client is added to smi_clients list
drm/amdgpu: Sync up header and implementation to use the same parameter names
drm/amdgpu: fix incorrect GCR_GENERAL_CNTL address
amd/display: set backlight only if required
drm/amd/display: Fix allocate_mst_payload assert on resume
drm/amd/display: Revert FEC check in validation
drm/amd/display: Add work around for AUX failure on wake.
drm/amd/display: Clear optc false state when disable otg
drm/amd/display: Enable power gating before init_pipes
drm/amd/display: Remove redundant dsc power gating from init_hw
drm/amd/display: Correct Slice reset calculation
...
[ upstream commit: 1831fed559732b132aef0ea8261ac77e73f7eadf ]
diff --git a/Bindings/net/ethernet-controller.yaml b/Bindings/net/ethernet-controller.yaml
index 817794e..4f15463 100644
--- a/Bindings/net/ethernet-controller.yaml
+++ b/Bindings/net/ethernet-controller.yaml
@@ -106,6 +106,12 @@
phy-mode:
$ref: "#/properties/phy-connection-type"
+ pcs-handle:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Specifies a reference to a node representing a PCS PHY device on a MDIO
+ bus to link with an external PHY (phy-handle) if exists.
+
phy-handle:
$ref: /schemas/types.yaml#/definitions/phandle
description:
diff --git a/Bindings/net/micrel.txt b/Bindings/net/micrel.txt
index c5ab62c..8d157f0 100644
--- a/Bindings/net/micrel.txt
+++ b/Bindings/net/micrel.txt
@@ -45,20 +45,3 @@
In fiber mode, auto-negotiation is disabled and the PHY can only work in
100base-fx (full and half duplex) modes.
-
- - lan8814,ignore-ts: If present the PHY will not support timestamping.
-
- This option acts as check whether Timestamping is supported by
- hardware or not. LAN8814 phy support hardware tmestamping.
-
- - lan8814,latency_rx_10: Configures Latency value of phy in ingress at 10 Mbps.
-
- - lan8814,latency_tx_10: Configures Latency value of phy in egress at 10 Mbps.
-
- - lan8814,latency_rx_100: Configures Latency value of phy in ingress at 100 Mbps.
-
- - lan8814,latency_tx_100: Configures Latency value of phy in egress at 100 Mbps.
-
- - lan8814,latency_rx_1000: Configures Latency value of phy in ingress at 1000 Mbps.
-
- - lan8814,latency_tx_1000: Configures Latency value of phy in egress at 1000 Mbps.
diff --git a/Bindings/net/xilinx_axienet.txt b/Bindings/net/xilinx_axienet.txt
index b8e4894..1aa4c60 100644
--- a/Bindings/net/xilinx_axienet.txt
+++ b/Bindings/net/xilinx_axienet.txt
@@ -26,7 +26,8 @@
specified, the TX/RX DMA interrupts should be on that node
instead, and only the Ethernet core interrupt is optionally
specified here.
-- phy-handle : Should point to the external phy device.
+- phy-handle : Should point to the external phy device if exists. Pointing
+ this to the PCS/PMA PHY is deprecated and should be avoided.
See ethernet.txt file in the same directory.
- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware
@@ -68,6 +69,11 @@
required through the core's MDIO interface (i.e. always,
unless the PHY is accessed through a different bus).
+ - pcs-handle: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
+ modes, where "pcs-handle" should be used to point
+ to the PCS/PMA PHY, and "phy-handle" should point to an
+ external PHY if exists.
+
Example:
axi_ethernet_eth: ethernet@40c00000 {
compatible = "xlnx,axi-ethernet-1.00.a";
