Merge tag 'v4.11-rc2-dts-raw'
Linux 4.11-rc2
diff --git a/Bindings/regulator/ti-abb-regulator.txt b/Bindings/regulator/ti-abb-regulator.txt
index c3f6546..6a23ad9 100644
--- a/Bindings/regulator/ti-abb-regulator.txt
+++ b/Bindings/regulator/ti-abb-regulator.txt
@@ -45,7 +45,7 @@
Optional Properties:
- reg-names: In addition to the required properties, the following are optional
- "efuse-address" - Contains efuse base address used to pick up ABB info.
- - "ldo-address" - Contains address of ABB LDO overide register address.
+ - "ldo-address" - Contains address of ABB LDO override register.
"efuse-address" is required for this.
- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override
register to provide override vset value.
diff --git a/Bindings/usb/usb251xb.txt b/Bindings/usb/usb251xb.txt
index 0c065f7..3957d4e 100644
--- a/Bindings/usb/usb251xb.txt
+++ b/Bindings/usb/usb251xb.txt
@@ -7,18 +7,18 @@
- compatible : Should be "microchip,usb251xb" or one of the specific types:
"microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b",
"microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi"
- - hub-reset-gpios : Should specify the gpio for hub reset
+ - reset-gpios : Should specify the gpio for hub reset
+ - reg : I2C address on the selected bus (default is <0x2C>)
Optional properties :
- - reg : I2C address on the selected bus (default is <0x2C>)
- skip-config : Skip Hub configuration, but only send the USB-Attach command
- - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424)
- - product-id : USB Product ID of the hub (16 bit, default depends on type)
- - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3)
- - language-id : USB Language ID (16 bit, default is 0x0000)
- - manufacturer : USB Manufacturer string (max 31 characters long)
- - product : USB Product string (max 31 characters long)
- - serial : USB Serial string (max 31 characters long)
+ - vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424)
+ - product-id : Set USB Product ID of the hub (16 bit, default depends on type)
+ - device-id : Set USB Device ID of the hub (16 bit, default is 0x0bb3)
+ - language-id : Set USB Language ID (16 bit, default is 0x0000)
+ - manufacturer : Set USB Manufacturer string (max 31 characters long)
+ - product : Set USB Product string (max 31 characters long)
+ - serial : Set USB Serial string (max 31 characters long)
- {bus,self}-powered : selects between self- and bus-powered operation (default
is self-powered)
- disable-hi-speed : disable USB Hi-Speed support
@@ -31,8 +31,10 @@
(default is individual)
- dynamic-power-switching : enable auto-switching from self- to bus-powered
operation if the local power source is removed or unavailable
- - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms)
- - compound-device : indicated the hub is part of a compound device
+ - oc-delay-us : Delay time (in microseconds) for filtering the over-current
+ sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If
+ an invalid value is given, the default is used instead.
+ - compound-device : indicate the hub is part of a compound device
- port-mapping-mode : enable port mapping mode
- string-support : enable string descriptor support (required for manufacturer,
product and serial string configuration)
@@ -40,34 +42,15 @@
device connected.
- sp-disabled-ports : Specifies the ports which will be self-power disabled
- bp-disabled-ports : Specifies the ports which will be bus-power disabled
- - max-sp-power : Specifies the maximum current the hub consumes from an
- upstream port when operating as self-powered hub including the power
- consumption of a permanently attached peripheral if the hub is
- configured as a compound device. The value is given in mA in a 0 - 500
- range (default is 2).
- - max-bp-power : Specifies the maximum current the hub consumes from an
- upstream port when operating as bus-powered hub including the power
- consumption of a permanently attached peripheral if the hub is
- configured as a compound device. The value is given in mA in a 0 - 500
- range (default is 100).
- - max-sp-current : Specifies the maximum current the hub consumes from an
- upstream port when operating as self-powered hub EXCLUDING the power
- consumption of a permanently attached peripheral if the hub is
- configured as a compound device. The value is given in mA in a 0 - 500
- range (default is 2).
- - max-bp-current : Specifies the maximum current the hub consumes from an
- upstream port when operating as bus-powered hub EXCLUDING the power
- consumption of a permanently attached peripheral if the hub is
- configured as a compound device. The value is given in mA in a 0 - 500
- range (default is 100).
- - power-on-time : Specifies the time it takes from the time the host initiates
- the power-on sequence to a port until the port has adequate power. The
- value is given in ms in a 0 - 510 range (default is 100ms).
+ - power-on-time-ms : Specifies the time it takes from the time the host
+ initiates the power-on sequence to a port until the port has adequate
+ power. The value is given in ms in a 0 - 510 range (default is 100ms).
Examples:
usb2512b@2c {
compatible = "microchip,usb2512b";
- hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ reg = <0x2c>;
+ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
};
usb2514b@2c {
diff --git a/include/dt-bindings/sound/cs42l42.h b/include/dt-bindings/sound/cs42l42.h
index 399a123..db69d84 100644
--- a/include/dt-bindings/sound/cs42l42.h
+++ b/include/dt-bindings/sound/cs42l42.h
@@ -20,7 +20,7 @@
#define CS42L42_HPOUT_LOAD_1NF 0
#define CS42L42_HPOUT_LOAD_10NF 1
-/* HPOUT Clamp to GND Overide */
+/* HPOUT Clamp to GND Override */
#define CS42L42_HPOUT_CLAMP_EN 0
#define CS42L42_HPOUT_CLAMP_DIS 1
