| # SPDX-License-Identifier: GPL-2.0 |
| config FB_OMAP2_DSS_INIT |
| bool |
| |
| config FB_OMAP2_DSS |
| tristate |
| select VIDEOMODE_HELPERS |
| select FB_OMAP2_DSS_INIT |
| select HDMI |
| |
| config FB_OMAP2_DSS_DEBUG |
| bool "Debug support" |
| default n |
| help |
| This enables printing of debug messages. Alternatively, debug messages |
| can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting |
| appropriate flags in <debugfs>/dynamic_debug/control. |
| |
| config FB_OMAP2_DSS_DEBUGFS |
| bool "Debugfs filesystem support" |
| depends on DEBUG_FS |
| default n |
| help |
| This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables |
| querying about clock configuration and register configuration of dss, |
| dispc, dsi, hdmi and rfbi. |
| |
| config FB_OMAP2_DSS_COLLECT_IRQ_STATS |
| bool "Collect DSS IRQ statistics" |
| depends on FB_OMAP2_DSS_DEBUGFS |
| default n |
| help |
| Collect DSS IRQ statistics, printable via debugfs. |
| |
| The statistics can be found from |
| <debugfs>/omapdss/dispc_irq for DISPC interrupts, and |
| <debugfs>/omapdss/dsi_irq for DSI interrupts. |
| |
| config FB_OMAP2_DSS_DPI |
| bool "DPI support" |
| default y |
| help |
| DPI Interface. This is the Parallel Display Interface. |
| |
| config FB_OMAP2_DSS_RFBI |
| bool "RFBI support" |
| depends on BROKEN |
| default n |
| help |
| MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas |
| Instrument's terminology). |
| |
| DBI is a bus between the host processor and a peripheral, |
| such as a display or a framebuffer chip. |
| |
| See http://www.mipi.org/ for DBI specifications. |
| |
| config FB_OMAP2_DSS_VENC |
| bool "VENC support" |
| default y |
| help |
| OMAP Video Encoder support for S-Video and composite TV-out. |
| |
| config FB_OMAP2_DSS_HDMI_COMMON |
| bool |
| |
| config FB_OMAP4_DSS_HDMI |
| bool "HDMI support for OMAP4" |
| default y |
| select FB_OMAP2_DSS_HDMI_COMMON |
| help |
| HDMI support for OMAP4 based SoCs. |
| |
| config FB_OMAP5_DSS_HDMI |
| bool "HDMI support for OMAP5" |
| default n |
| select FB_OMAP2_DSS_HDMI_COMMON |
| help |
| HDMI Interface for OMAP5 and similar cores. This adds the High |
| Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI |
| specification. |
| |
| config FB_OMAP2_DSS_SDI |
| bool "SDI support" |
| default n |
| help |
| SDI (Serial Display Interface) support. |
| |
| SDI is a high speed one-way display serial bus between the host |
| processor and a display. |
| |
| config FB_OMAP2_DSS_DSI |
| bool "DSI support" |
| default n |
| help |
| MIPI DSI (Display Serial Interface) support. |
| |
| DSI is a high speed half-duplex serial interface between the host |
| processor and a peripheral, such as a display or a framebuffer chip. |
| |
| See http://www.mipi.org/ for DSI specifications. |
| |
| config FB_OMAP2_DSS_MIN_FCK_PER_PCK |
| int "Minimum FCK/PCK ratio (for scaling)" |
| range 0 32 |
| default 0 |
| help |
| This can be used to adjust the minimum FCK/PCK ratio. |
| |
| With this you can make sure that DISPC FCK is at least |
| n x PCK. Video plane scaling requires higher FCK than |
| normally. |
| |
| If this is set to 0, there's no extra constraint on the |
| DISPC FCK. However, the FCK will at minimum be |
| 2xPCK (if active matrix) or 3xPCK (if passive matrix). |
| |
| Max FCK is 173MHz, so this doesn't work if your PCK |
| is very high. |
| |
| config FB_OMAP2_DSS_SLEEP_AFTER_VENC_RESET |
| bool "Sleep 20ms after VENC reset" |
| default y |
| help |
| There is a 20ms sleep after VENC reset which seemed to fix the |
| reset. The reason for the bug is unclear, and it's also unclear |
| on what platforms this happens. |
| |
| This option enables the sleep, and is enabled by default. You can |
| disable the sleep if it doesn't cause problems on your platform. |
