blob: e46ebaea7b1edba4cfa6f8a0e904977cd7cc320c [file] [log] [blame]
/* ------------------------------------------------------------------------- */
/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */
/* ------------------------------------------------------------------------- */
/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
* <Peter dot Milne at D hyphen TACQ dot com>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, version 2.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
/* ------------------------------------------------------------------------- */
#ifndef I2C_IOP3XX_H
#define I2C_IOP3XX_H 1
/*
* iop321 hardware bit definitions
*/
#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */
#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */
#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */
#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */
#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */
#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */
#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */
#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */
#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */
/*
* IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
* when sending a master mode general call message from the I2C unit"
*/
#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */
/*
* "NOTE: To avoid I2C bus integrity problems,
* the user needs to ensure that the GPIO Output Data Register -
* GPOD bits associated with an I2C port are cleared prior to setting
* the enable bit for that I2C serial port.
* The user prepares to enable I2C port 0 and
* I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
*/
#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */
#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data
* NB TBYTE must be clear */
#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */
#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */
#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */
#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */
#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */
#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */
#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */
#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */
#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */
#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */
#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */
#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */
#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */
#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */
#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */
#define IOP3XX_ISR_CLEARBITS 0x07f0
#define IOP3XX_ISAR_SAMASK 0x007f
#define IOP3XX_IDBR_MASK 0x00ff
#define IOP3XX_IBMR_SCL 0x0002
#define IOP3XX_IBMR_SDA 0x0001
#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
#define MYSAR 0x02 /* SWAG a suitable slave address */
#define I2C_ERR 321
#define I2C_ERR_BERR (I2C_ERR+0)
#define I2C_ERR_ALD (I2C_ERR+1)
#define CR_OFFSET 0
#define SR_OFFSET 0x4
#define SAR_OFFSET 0x8
#define DBR_OFFSET 0xc
#define CCR_OFFSET 0x10
#define BMR_OFFSET 0x14
#define IOP3XX_I2C_IO_SIZE 0x18
struct i2c_algo_iop3xx_data {
u32 ioaddr;
wait_queue_head_t waitq;
spinlock_t lock;
u32 SR_enabled, SR_received;
int id;
};
#endif /* I2C_IOP3XX_H */