| /* |
| * WaveLAN ISA driver |
| * |
| * Jean II - HPLB '96 |
| * |
| * Reorganisation and extension of the driver. |
| * Original copyright follows. See wavelan.p.h for details. |
| * |
| * This file contains the declarations for the WaveLAN hardware. Note that |
| * the WaveLAN ISA includes a i82586 controller (see definitions in |
| * file i82586.h). |
| * |
| * The main difference between the ISA hardware and the PCMCIA one is |
| * the Ethernet controller (i82586 instead of i82593). |
| * The i82586 allows multiple transmit buffers. The PSA needs to be accessed |
| * through the host interface. |
| */ |
| |
| #ifndef _WAVELAN_H |
| #define _WAVELAN_H |
| |
| /************************** MAGIC NUMBERS ***************************/ |
| |
| /* Detection of the WaveLAN card is done by reading the MAC |
| * address from the card and checking it. If you have a non-AT&T |
| * product (OEM, like DEC RoamAbout, Digital Ocean, or Epson), |
| * you might need to modify this part to accommodate your hardware. |
| */ |
| static const char MAC_ADDRESSES[][3] = |
| { |
| { 0x08, 0x00, 0x0E }, /* AT&T WaveLAN (standard) & DEC RoamAbout */ |
| { 0x08, 0x00, 0x6A }, /* AT&T WaveLAN (alternate) */ |
| { 0x00, 0x00, 0xE1 }, /* Hitachi Wavelan */ |
| { 0x00, 0x60, 0x1D } /* Lucent Wavelan (another one) */ |
| /* Add your card here and send me the patch! */ |
| }; |
| |
| #define WAVELAN_ADDR_SIZE 6 /* Size of a MAC address */ |
| |
| #define WAVELAN_MTU 1500 /* Maximum size of WaveLAN packet */ |
| |
| #define MAXDATAZ (WAVELAN_ADDR_SIZE + WAVELAN_ADDR_SIZE + 2 + WAVELAN_MTU) |
| |
| /* |
| * Constants used to convert channels to frequencies |
| */ |
| |
| /* Frequency available in the 2.0 modem, in units of 250 kHz |
| * (as read in the offset register of the dac area). |
| * Used to map channel numbers used by `wfreqsel' to frequencies |
| */ |
| static const short channel_bands[] = { 0x30, 0x58, 0x64, 0x7A, 0x80, 0xA8, |
| 0xD0, 0xF0, 0xF8, 0x150 }; |
| |
| /* Frequencies of the 1.0 modem (fixed frequencies). |
| * Use to map the PSA `subband' to a frequency |
| * Note : all frequencies apart from the first one need to be multiplied by 10 |
| */ |
| static const int fixed_bands[] = { 915e6, 2.425e8, 2.46e8, 2.484e8, 2.4305e8 }; |
| |
| |
| |
| /*************************** PC INTERFACE ****************************/ |
| |
| /* |
| * Host Adaptor structure. |
| * (base is board port address). |
| */ |
| typedef union hacs_u hacs_u; |
| union hacs_u |
| { |
| unsigned short hu_command; /* Command register */ |
| #define HACR_RESET 0x0001 /* Reset board */ |
| #define HACR_CA 0x0002 /* Set Channel Attention for 82586 */ |
| #define HACR_16BITS 0x0004 /* 16-bit operation (0 => 8bits) */ |
| #define HACR_OUT0 0x0008 /* General purpose output pin 0 */ |
| /* not used - must be 1 */ |
| #define HACR_OUT1 0x0010 /* General purpose output pin 1 */ |
| /* not used - must be 1 */ |
| #define HACR_82586_INT_ENABLE 0x0020 /* Enable 82586 interrupts */ |
| #define HACR_MMC_INT_ENABLE 0x0040 /* Enable MMC interrupts */ |
| #define HACR_INTR_CLR_ENABLE 0x0080 /* Enable interrupt status read/clear */ |
| unsigned short hu_status; /* Status Register */ |
| #define HASR_82586_INTR 0x0001 /* Interrupt request from 82586 */ |
| #define HASR_MMC_INTR 0x0002 /* Interrupt request from MMC */ |
| #define HASR_MMC_BUSY 0x0004 /* MMC busy indication */ |
| #define HASR_PSA_BUSY 0x0008 /* LAN parameter storage area busy */ |
| }; |
| |
| typedef struct ha_t ha_t; |
| struct ha_t |
| { |
| hacs_u ha_cs; /* Command and status registers */ |
| #define ha_command ha_cs.hu_command |
| #define ha_status ha_cs.hu_status |
| unsigned short ha_mmcr; /* Modem Management Ctrl Register */ |
| unsigned short ha_pior0; /* Program I/O Address Register Port 0 */ |
| unsigned short ha_piop0; /* Program I/O Port 0 */ |
| unsigned short ha_pior1; /* Program I/O Address Register Port 1 */ |
| unsigned short ha_piop1; /* Program I/O Port 1 */ |
| unsigned short ha_pior2; /* Program I/O Address Register Port 2 */ |
| unsigned short ha_piop2; /* Program I/O Port 2 */ |
| }; |
| |
| #define HA_SIZE 16 |
| |
| #define hoff(p,f) (unsigned short)((void *)(&((ha_t *)((void *)0 + (p)))->f) - (void *)0) |
| #define HACR(p) hoff(p, ha_command) |
| #define HASR(p) hoff(p, ha_status) |
| #define MMCR(p) hoff(p, ha_mmcr) |
| #define PIOR0(p) hoff(p, ha_pior0) |
| #define PIOP0(p) hoff(p, ha_piop0) |
| #define PIOR1(p) hoff(p, ha_pior1) |
| #define PIOP1(p) hoff(p, ha_piop1) |
| #define PIOR2(p) hoff(p, ha_pior2) |
| #define PIOP2(p) hoff(p, ha_piop2) |
| |
| /* |
| * Program I/O Mode Register values. |
| */ |
| #define STATIC_PIO 0 /* Mode 1: static mode */ |
| /* RAM access ??? */ |
| #define AUTOINCR_PIO 1 /* Mode 2: auto increment mode */ |
| /* RAM access ??? */ |
| #define AUTODECR_PIO 2 /* Mode 3: auto decrement mode */ |
| /* RAM access ??? */ |
| #define PARAM_ACCESS_PIO 3 /* Mode 4: LAN parameter access mode */ |
| /* Parameter access. */ |
| #define PIO_MASK 3 /* register mask */ |
| #define PIOM(cmd,piono) ((u_short)cmd << 10 << (piono * 2)) |
| |
| #define HACR_DEFAULT (HACR_OUT0 | HACR_OUT1 | HACR_16BITS | PIOM(STATIC_PIO, 0) | PIOM(AUTOINCR_PIO, 1) | PIOM(PARAM_ACCESS_PIO, 2)) |
| #define HACR_INTRON (HACR_82586_INT_ENABLE | HACR_MMC_INT_ENABLE | HACR_INTR_CLR_ENABLE) |
| |
| /************************** MEMORY LAYOUT **************************/ |
| |
| /* |
| * Onboard 64 k RAM layout. |
| * (Offsets from 0x0000.) |
| */ |
| #define OFFSET_RU 0x0000 /* 75% memory */ |
| #define OFFSET_CU 0xC000 /* 25% memory */ |
| #define OFFSET_SCB (OFFSET_ISCP - sizeof(scb_t)) |
| #define OFFSET_ISCP (OFFSET_SCP - sizeof(iscp_t)) |
| #define OFFSET_SCP I82586_SCP_ADDR |
| |
| #define RXBLOCKZ (sizeof(fd_t) + sizeof(rbd_t) + MAXDATAZ) |
| #define TXBLOCKZ (sizeof(ac_tx_t) + sizeof(ac_nop_t) + sizeof(tbd_t) + MAXDATAZ) |
| |
| #define NRXBLOCKS ((OFFSET_CU - OFFSET_RU) / RXBLOCKZ) |
| #define NTXBLOCKS ((OFFSET_SCB - OFFSET_CU) / TXBLOCKZ) |
| |
| /********************** PARAMETER STORAGE AREA **********************/ |
| |
| /* |
| * Parameter Storage Area (PSA). |
| */ |
| typedef struct psa_t psa_t; |
| struct psa_t |
| { |
| unsigned char psa_io_base_addr_1; /* [0x00] Base address 1 ??? */ |
| unsigned char psa_io_base_addr_2; /* [0x01] Base address 2 */ |
| unsigned char psa_io_base_addr_3; /* [0x02] Base address 3 */ |
| unsigned char psa_io_base_addr_4; /* [0x03] Base address 4 */ |
| unsigned char psa_rem_boot_addr_1; /* [0x04] Remote Boot Address 1 */ |
| unsigned char psa_rem_boot_addr_2; /* [0x05] Remote Boot Address 2 */ |
| unsigned char psa_rem_boot_addr_3; /* [0x06] Remote Boot Address 3 */ |
| unsigned char psa_holi_params; /* [0x07] HOst Lan Interface (HOLI) Parameters */ |
| unsigned char psa_int_req_no; /* [0x08] Interrupt Request Line */ |
| unsigned char psa_unused0[7]; /* [0x09-0x0F] unused */ |
| |
| unsigned char psa_univ_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x10-0x15] Universal (factory) MAC Address */ |
| unsigned char psa_local_mac_addr[WAVELAN_ADDR_SIZE]; /* [0x16-1B] Local MAC Address */ |
| unsigned char psa_univ_local_sel; /* [0x1C] Universal Local Selection */ |
| #define PSA_UNIVERSAL 0 /* Universal (factory) */ |
| #define PSA_LOCAL 1 /* Local */ |
| unsigned char psa_comp_number; /* [0x1D] Compatibility Number: */ |
| #define PSA_COMP_PC_AT_915 0 /* PC-AT 915 MHz */ |
| #define PSA_COMP_PC_MC_915 1 /* PC-MC 915 MHz */ |
| #define PSA_COMP_PC_AT_2400 2 /* PC-AT 2.4 GHz */ |
| #define PSA_COMP_PC_MC_2400 3 /* PC-MC 2.4 GHz */ |
| #define PSA_COMP_PCMCIA_915 4 /* PCMCIA 915 MHz or 2.0 */ |
| unsigned char psa_thr_pre_set; /* [0x1E] Modem Threshold Preset */ |
| unsigned char psa_feature_select; /* [0x1F] Call code required (1=on) */ |
| #define PSA_FEATURE_CALL_CODE 0x01 /* Call code required (Japan) */ |
| unsigned char psa_subband; /* [0x20] Subband */ |
| #define PSA_SUBBAND_915 0 /* 915 MHz or 2.0 */ |
| #define PSA_SUBBAND_2425 1 /* 2425 MHz */ |
| #define PSA_SUBBAND_2460 2 /* 2460 MHz */ |
| #define PSA_SUBBAND_2484 3 /* 2484 MHz */ |
| #define PSA_SUBBAND_2430_5 4 /* 2430.5 MHz */ |
| unsigned char psa_quality_thr; /* [0x21] Modem Quality Threshold */ |
| unsigned char psa_mod_delay; /* [0x22] Modem Delay (?) (reserved) */ |
| unsigned char psa_nwid[2]; /* [0x23-0x24] Network ID */ |
| unsigned char psa_nwid_select; /* [0x25] Network ID Select On/Off */ |
| unsigned char psa_encryption_select; /* [0x26] Encryption On/Off */ |
| unsigned char psa_encryption_key[8]; /* [0x27-0x2E] Encryption Key */ |
| unsigned char psa_databus_width; /* [0x2F] AT bus width select 8/16 */ |
| unsigned char psa_call_code[8]; /* [0x30-0x37] (Japan) Call Code */ |
| unsigned char psa_nwid_prefix[2]; /* [0x38-0x39] Roaming domain */ |
| unsigned char psa_reserved[2]; /* [0x3A-0x3B] Reserved - fixed 00 */ |
| unsigned char psa_conf_status; /* [0x3C] Conf Status, bit 0=1:config*/ |
| unsigned char psa_crc[2]; /* [0x3D] CRC-16 over PSA */ |
| unsigned char psa_crc_status; /* [0x3F] CRC Valid Flag */ |
| }; |
| |
| #define PSA_SIZE 64 |
| |
| /* Calculate offset of a field in the above structure. |
| * Warning: only even addresses are used. */ |
| #define psaoff(p,f) ((unsigned short) ((void *)(&((psa_t *) ((void *) NULL + (p)))->f) - (void *) NULL)) |
| |
| /******************** MODEM MANAGEMENT INTERFACE ********************/ |
| |
| /* |
| * Modem Management Controller (MMC) write structure. |
| */ |
| typedef struct mmw_t mmw_t; |
| struct mmw_t |
| { |
| unsigned char mmw_encr_key[8]; /* encryption key */ |
| unsigned char mmw_encr_enable; /* Enable or disable encryption. */ |
| #define MMW_ENCR_ENABLE_MODE 0x02 /* mode of security option */ |
| #define MMW_ENCR_ENABLE_EN 0x01 /* Enable security option. */ |
| unsigned char mmw_unused0[1]; /* unused */ |
| unsigned char mmw_des_io_invert; /* encryption option */ |
| #define MMW_DES_IO_INVERT_RES 0x0F /* reserved */ |
| #define MMW_DES_IO_INVERT_CTRL 0xF0 /* control (?) (set to 0) */ |
| unsigned char mmw_unused1[5]; /* unused */ |
| unsigned char mmw_loopt_sel; /* looptest selection */ |
| #define MMW_LOOPT_SEL_DIS_NWID 0x40 /* Disable NWID filtering. */ |
| #define MMW_LOOPT_SEL_INT 0x20 /* Activate Attention Request. */ |
| #define MMW_LOOPT_SEL_LS 0x10 /* looptest, no collision avoidance */ |
| #define MMW_LOOPT_SEL_LT3A 0x08 /* looptest 3a */ |
| #define MMW_LOOPT_SEL_LT3B 0x04 /* looptest 3b */ |
| #define MMW_LOOPT_SEL_LT3C 0x02 /* looptest 3c */ |
| #define MMW_LOOPT_SEL_LT3D 0x01 /* looptest 3d */ |
| unsigned char mmw_jabber_enable; /* jabber timer enable */ |
| /* Abort transmissions > 200 ms */ |
| unsigned char mmw_freeze; /* freeze or unfreeze signal level */ |
| /* 0 : signal level & qual updated for every new message, 1 : frozen */ |
| unsigned char mmw_anten_sel; /* antenna selection */ |
| #define MMW_ANTEN_SEL_SEL 0x01 /* direct antenna selection */ |
| #define MMW_ANTEN_SEL_ALG_EN 0x02 /* antenna selection algo. enable */ |
| unsigned char mmw_ifs; /* inter frame spacing */ |
| /* min time between transmission in bit periods (.5 us) - bit 0 ignored */ |
| unsigned char mmw_mod_delay; /* modem delay (synchro) */ |
| unsigned char mmw_jam_time; /* jamming time (after collision) */ |
| unsigned char mmw_unused2[1]; /* unused */ |
| unsigned char mmw_thr_pre_set; /* level threshold preset */ |
| /* Discard all packet with signal < this value (4) */ |
| unsigned char mmw_decay_prm; /* decay parameters */ |
| unsigned char mmw_decay_updat_prm; /* decay update parameters */ |
| unsigned char mmw_quality_thr; /* quality (z-quotient) threshold */ |
| /* Discard all packet with quality < this value (3) */ |
| unsigned char mmw_netw_id_l; /* NWID low order byte */ |
| unsigned char mmw_netw_id_h; /* NWID high order byte */ |
| /* Network ID or Domain : create virtual net on the air */ |
| |
| /* 2.0 Hardware extension - frequency selection support */ |
| unsigned char mmw_mode_select; /* for analog tests (set to 0) */ |
| unsigned char mmw_unused3[1]; /* unused */ |
| unsigned char mmw_fee_ctrl; /* frequency EEPROM control */ |
| #define MMW_FEE_CTRL_PRE 0x10 /* Enable protected instructions. */ |
| #define MMW_FEE_CTRL_DWLD 0x08 /* Download EEPROM to mmc. */ |
| #define MMW_FEE_CTRL_CMD 0x07 /* EEPROM commands: */ |
| #define MMW_FEE_CTRL_READ 0x06 /* Read */ |
| #define MMW_FEE_CTRL_WREN 0x04 /* Write enable */ |
| #define MMW_FEE_CTRL_WRITE 0x05 /* Write data to address. */ |
| #define MMW_FEE_CTRL_WRALL 0x04 /* Write data to all addresses. */ |
| #define MMW_FEE_CTRL_WDS 0x04 /* Write disable */ |
| #define MMW_FEE_CTRL_PRREAD 0x16 /* Read addr from protect register */ |
| #define MMW_FEE_CTRL_PREN 0x14 /* Protect register enable */ |
| #define MMW_FEE_CTRL_PRCLEAR 0x17 /* Unprotect all registers. */ |
| #define MMW_FEE_CTRL_PRWRITE 0x15 /* Write address in protect register */ |
| #define MMW_FEE_CTRL_PRDS 0x14 /* Protect register disable */ |
| /* Never issue the PRDS command: it's irreversible! */ |
| |
| unsigned char mmw_fee_addr; /* EEPROM address */ |
| #define MMW_FEE_ADDR_CHANNEL 0xF0 /* Select the channel. */ |
| #define MMW_FEE_ADDR_OFFSET 0x0F /* Offset in channel data */ |
| #define MMW_FEE_ADDR_EN 0xC0 /* FEE_CTRL enable operations */ |
| #define MMW_FEE_ADDR_DS 0x00 /* FEE_CTRL disable operations */ |
| #define MMW_FEE_ADDR_ALL 0x40 /* FEE_CTRL all operations */ |
| #define MMW_FEE_ADDR_CLEAR 0xFF /* FEE_CTRL clear operations */ |
| |
| unsigned char mmw_fee_data_l; /* Write data to EEPROM. */ |
| unsigned char mmw_fee_data_h; /* high octet */ |
| unsigned char mmw_ext_ant; /* Setting for external antenna */ |
| #define MMW_EXT_ANT_EXTANT 0x01 /* Select external antenna */ |
| #define MMW_EXT_ANT_POL 0x02 /* Polarity of the antenna */ |
| #define MMW_EXT_ANT_INTERNAL 0x00 /* Internal antenna */ |
| #define MMW_EXT_ANT_EXTERNAL 0x03 /* External antenna */ |
| #define MMW_EXT_ANT_IQ_TEST 0x1C /* IQ test pattern (set to 0) */ |
| }; |
| |
| #define MMW_SIZE 37 |
| |
| #define mmwoff(p,f) (unsigned short)((void *)(&((mmw_t *)((void *)0 + (p)))->f) - (void *)0) |
| |
| /* |
| * Modem Management Controller (MMC) read structure. |
| */ |
| typedef struct mmr_t mmr_t; |
| struct mmr_t |
| { |
| unsigned char mmr_unused0[8]; /* unused */ |
| unsigned char mmr_des_status; /* encryption status */ |
| unsigned char mmr_des_avail; /* encryption available (0x55 read) */ |
| #define MMR_DES_AVAIL_DES 0x55 /* DES available */ |
| #define MMR_DES_AVAIL_AES 0x33 /* AES (AT&T) available */ |
| unsigned char mmr_des_io_invert; /* des I/O invert register */ |
| unsigned char mmr_unused1[5]; /* unused */ |
| unsigned char mmr_dce_status; /* DCE status */ |
| #define MMR_DCE_STATUS_RX_BUSY 0x01 /* receiver busy */ |
| #define MMR_DCE_STATUS_LOOPT_IND 0x02 /* loop test indicated */ |
| #define MMR_DCE_STATUS_TX_BUSY 0x04 /* transmitter on */ |
| #define MMR_DCE_STATUS_JBR_EXPIRED 0x08 /* jabber timer expired */ |
| #define MMR_DCE_STATUS 0x0F /* mask to get the bits */ |
| unsigned char mmr_dsp_id; /* DSP ID (AA = Daedalus rev A) */ |
| unsigned char mmr_unused2[2]; /* unused */ |
| unsigned char mmr_correct_nwid_l; /* # of correct NWIDs rxd (low) */ |
| unsigned char mmr_correct_nwid_h; /* # of correct NWIDs rxd (high) */ |
| /* Warning: read high-order octet first! */ |
| unsigned char mmr_wrong_nwid_l; /* # of wrong NWIDs rxd (low) */ |
| unsigned char mmr_wrong_nwid_h; /* # of wrong NWIDs rxd (high) */ |
| unsigned char mmr_thr_pre_set; /* level threshold preset */ |
| #define MMR_THR_PRE_SET 0x3F /* level threshold preset */ |
| #define MMR_THR_PRE_SET_CUR 0x80 /* Current signal above it */ |
| unsigned char mmr_signal_lvl; /* signal level */ |
| #define MMR_SIGNAL_LVL 0x3F /* signal level */ |
| #define MMR_SIGNAL_LVL_VALID 0x80 /* Updated since last read */ |
| unsigned char mmr_silence_lvl; /* silence level (noise) */ |
| #define MMR_SILENCE_LVL 0x3F /* silence level */ |
| #define MMR_SILENCE_LVL_VALID 0x80 /* Updated since last read */ |
| unsigned char mmr_sgnl_qual; /* signal quality */ |
| #define MMR_SGNL_QUAL 0x0F /* signal quality */ |
| #define MMR_SGNL_QUAL_ANT 0x80 /* current antenna used */ |
| unsigned char mmr_netw_id_l; /* NWID low order byte (?) */ |
| unsigned char mmr_unused3[3]; /* unused */ |
| |
| /* 2.0 Hardware extension - frequency selection support */ |
| unsigned char mmr_fee_status; /* Status of frequency EEPROM */ |
| #define MMR_FEE_STATUS_ID 0xF0 /* Modem revision ID */ |
| #define MMR_FEE_STATUS_DWLD 0x08 /* Download in progress */ |
| #define MMR_FEE_STATUS_BUSY 0x04 /* EEPROM busy */ |
| unsigned char mmr_unused4[1]; /* unused */ |
| unsigned char mmr_fee_data_l; /* Read data from EEPROM (low) */ |
| unsigned char mmr_fee_data_h; /* Read data from EEPROM (high) */ |
| }; |
| |
| #define MMR_SIZE 36 |
| |
| #define mmroff(p,f) (unsigned short)((void *)(&((mmr_t *)((void *)0 + (p)))->f) - (void *)0) |
| |
| /* Make the two above structures one */ |
| typedef union mm_t |
| { |
| struct mmw_t w; /* Write to the mmc */ |
| struct mmr_t r; /* Read from the mmc */ |
| } mm_t; |
| |
| #endif /* _WAVELAN_H */ |
| |
| /* |
| * This software may only be used and distributed |
| * according to the terms of the GNU General Public License. |
| * |
| * For more details, see wavelan.c. |
| */ |
