Merge tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.1-rc3.
Nothing major at all here, just a small collection of fixes for
reported issues, and potential problems with error handling paths.
Also a few new device ids, as normal.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: serial: option: add Olicard 600
USB: serial: cp210x: add new device id
usb: u132-hcd: fix resource leak
usb: cdc-acm: fix race during wakeup blocking TX traffic
usb: mtu3: fix EXTCON dependency
usb: usb251xb: fix to avoid potential NULL pointer dereference
usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
xhci: Don't let USB3 ports stuck in polling state prevent suspend
usb: xhci: dbc: Don't free all memory with spinlock held
xhci: Fix port resume done detection for SS ports with LPM enabled
USB: serial: mos7720: fix mos_parport refcount imbalance on error path
USB: gadget: f_hid: fix deadlock in f_hidg_write()
usb: gadget: net2272: Fix net2272_dequeue()
usb: gadget: net2280: Fix net2280_dequeue()
usb: gadget: net2280: Fix overrun of OUT messages
usb: dwc3: pci: add support for Comet Lake PCH ID
usb: usb251xb: Remove unnecessary comparison of unsigned integer with >= 0
usb: common: Consider only available nodes for dr_mode
usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
...
diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
index 5163097..4bbd9ed 100644
--- a/drivers/phy/allwinner/phy-sun4i-usb.c
+++ b/drivers/phy/allwinner/phy-sun4i-usb.c
@@ -485,8 +485,11 @@
struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
int new_mode;
- if (phy->index != 0)
+ if (phy->index != 0) {
+ if (mode == PHY_MODE_USB_HOST)
+ return 0;
return -EINVAL;
+ }
switch (mode) {
case PHY_MODE_USB_HOST:
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index 739f896..ec666eb 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -558,10 +558,8 @@
clear_bit(EVENT_RX_STALL, &acm->flags);
}
- if (test_bit(EVENT_TTY_WAKEUP, &acm->flags)) {
+ if (test_and_clear_bit(EVENT_TTY_WAKEUP, &acm->flags))
tty_port_tty_wakeup(&acm->port);
- clear_bit(EVENT_TTY_WAKEUP, &acm->flags);
- }
}
/*
diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index 48277bb..73c8e65 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -145,6 +145,8 @@
do {
controller = of_find_node_with_property(controller, "phys");
+ if (!of_device_is_available(controller))
+ continue;
index = 0;
do {
if (arg0 == -1) {
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 3189181..975d7c1 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -2742,6 +2742,9 @@
retval = usb_phy_roothub_set_mode(hcd->phy_roothub,
PHY_MODE_USB_HOST_SS);
if (retval)
+ retval = usb_phy_roothub_set_mode(hcd->phy_roothub,
+ PHY_MODE_USB_HOST);
+ if (retval)
goto err_usb_phy_roothub_power_on;
retval = usb_phy_roothub_power_on(hcd->phy_roothub);
diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c
index fdc6e4e..8cced36 100644
--- a/drivers/usb/dwc3/dwc3-pci.c
+++ b/drivers/usb/dwc3/dwc3-pci.c
@@ -29,6 +29,7 @@
#define PCI_DEVICE_ID_INTEL_BXT_M 0x1aaa
#define PCI_DEVICE_ID_INTEL_APL 0x5aaa
#define PCI_DEVICE_ID_INTEL_KBP 0xa2b0
+#define PCI_DEVICE_ID_INTEL_CMLH 0x02ee
#define PCI_DEVICE_ID_INTEL_GLK 0x31aa
#define PCI_DEVICE_ID_INTEL_CNPLP 0x9dee
#define PCI_DEVICE_ID_INTEL_CNPH 0xa36e
@@ -305,6 +306,9 @@
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MRFLD),
(kernel_ulong_t) &dwc3_pci_mrfld_properties, },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_CMLH),
+ (kernel_ulong_t) &dwc3_pci_intel_properties, },
+
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_SPTLP),
(kernel_ulong_t) &dwc3_pci_intel_properties, },
diff --git a/drivers/usb/gadget/function/f_hid.c b/drivers/usb/gadget/function/f_hid.c
index 75b113a..f3816a5 100644
--- a/drivers/usb/gadget/function/f_hid.c
+++ b/drivers/usb/gadget/function/f_hid.c
@@ -391,20 +391,20 @@
req->complete = f_hidg_req_complete;
req->context = hidg;
+ spin_unlock_irqrestore(&hidg->write_spinlock, flags);
+
status = usb_ep_queue(hidg->in_ep, req, GFP_ATOMIC);
if (status < 0) {
ERROR(hidg->func.config->cdev,
"usb_ep_queue error on int endpoint %zd\n", status);
- goto release_write_pending_unlocked;
+ goto release_write_pending;
} else {
status = count;
}
- spin_unlock_irqrestore(&hidg->write_spinlock, flags);
return status;
release_write_pending:
spin_lock_irqsave(&hidg->write_spinlock, flags);
-release_write_pending_unlocked:
hidg->write_pending = 0;
spin_unlock_irqrestore(&hidg->write_spinlock, flags);
diff --git a/drivers/usb/gadget/udc/net2272.c b/drivers/usb/gadget/udc/net2272.c
index b77f312..c2011cd 100644
--- a/drivers/usb/gadget/udc/net2272.c
+++ b/drivers/usb/gadget/udc/net2272.c
@@ -945,6 +945,7 @@
break;
}
if (&req->req != _req) {
+ ep->stopped = stopped;
spin_unlock_irqrestore(&ep->dev->lock, flags);
return -EINVAL;
}
diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index f63f824..898339e5 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -866,9 +866,6 @@
(void) readl(&ep->dev->pci->pcimstctl);
writel(BIT(DMA_START), &dma->dmastat);
-
- if (!ep->is_in)
- stop_out_naking(ep);
}
static void start_dma(struct net2280_ep *ep, struct net2280_request *req)
@@ -907,6 +904,7 @@
writel(BIT(DMA_START), &dma->dmastat);
return;
}
+ stop_out_naking(ep);
}
tmp = dmactl_default;
@@ -1275,9 +1273,9 @@
break;
}
if (&req->req != _req) {
+ ep->stopped = stopped;
spin_unlock_irqrestore(&ep->dev->lock, flags);
- dev_err(&ep->dev->pdev->dev, "%s: Request mismatch\n",
- __func__);
+ ep_dbg(ep->dev, "%s: Request mismatch\n", __func__);
return -EINVAL;
}
diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c
index 934584f..6343fba 100644
--- a/drivers/usb/host/u132-hcd.c
+++ b/drivers/usb/host/u132-hcd.c
@@ -3204,6 +3204,9 @@
printk(KERN_INFO "driver %s\n", hcd_name);
workqueue = create_singlethread_workqueue("u132");
retval = platform_driver_register(&u132_platform_driver);
+ if (retval)
+ destroy_workqueue(workqueue);
+
return retval;
}
diff --git a/drivers/usb/host/xhci-dbgcap.c b/drivers/usb/host/xhci-dbgcap.c
index c78be57..d932cc3 100644
--- a/drivers/usb/host/xhci-dbgcap.c
+++ b/drivers/usb/host/xhci-dbgcap.c
@@ -516,7 +516,6 @@
return -1;
writel(0, &dbc->regs->control);
- xhci_dbc_mem_cleanup(xhci);
dbc->state = DS_DISABLED;
return 0;
@@ -562,8 +561,10 @@
ret = xhci_do_dbc_stop(xhci);
spin_unlock_irqrestore(&dbc->lock, flags);
- if (!ret)
+ if (!ret) {
+ xhci_dbc_mem_cleanup(xhci);
pm_runtime_put_sync(xhci_to_hcd(xhci)->self.controller);
+ }
}
static void
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index e2eece6..96a7405 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -1545,20 +1545,25 @@
port_index = max_ports;
while (port_index--) {
u32 t1, t2;
-
+ int retries = 10;
+retry:
t1 = readl(ports[port_index]->addr);
t2 = xhci_port_state_to_neutral(t1);
portsc_buf[port_index] = 0;
- /* Bail out if a USB3 port has a new device in link training */
- if ((hcd->speed >= HCD_USB3) &&
+ /*
+ * Give a USB3 port in link training time to finish, but don't
+ * prevent suspend as port might be stuck
+ */
+ if ((hcd->speed >= HCD_USB3) && retries-- &&
(t1 & PORT_PLS_MASK) == XDEV_POLLING) {
- bus_state->bus_suspended = 0;
spin_unlock_irqrestore(&xhci->lock, flags);
- xhci_dbg(xhci, "Bus suspend bailout, port in polling\n");
- return -EBUSY;
+ msleep(XHCI_PORT_POLLING_LFPS_TIME);
+ spin_lock_irqsave(&xhci->lock, flags);
+ xhci_dbg(xhci, "port %d polling in bus suspend, waiting\n",
+ port_index);
+ goto retry;
}
-
/* suspend ports in U0, or bail out for new connect changes */
if ((t1 & PORT_PE) && (t1 & PORT_PLS_MASK) == XDEV_U0) {
if ((t1 & PORT_CSC) && wake_enabled) {
diff --git a/drivers/usb/host/xhci-rcar.c b/drivers/usb/host/xhci-rcar.c
index a6e4637..671bce1 100644
--- a/drivers/usb/host/xhci-rcar.c
+++ b/drivers/usb/host/xhci-rcar.c
@@ -246,6 +246,7 @@
if (!xhci_rcar_wait_for_pll_active(hcd))
return -ETIMEDOUT;
+ xhci->quirks |= XHCI_TRUST_TX_LENGTH;
return xhci_rcar_download_firmware(hcd);
}
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 40fa25c..9215a28 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1647,10 +1647,13 @@
}
}
- if ((portsc & PORT_PLC) && (portsc & PORT_PLS_MASK) == XDEV_U0 &&
- DEV_SUPERSPEED_ANY(portsc)) {
+ if ((portsc & PORT_PLC) &&
+ DEV_SUPERSPEED_ANY(portsc) &&
+ ((portsc & PORT_PLS_MASK) == XDEV_U0 ||
+ (portsc & PORT_PLS_MASK) == XDEV_U1 ||
+ (portsc & PORT_PLS_MASK) == XDEV_U2)) {
xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
- /* We've just brought the device into U0 through either the
+ /* We've just brought the device into U0/1/2 through either the
* Resume state after a device remote wakeup, or through the
* U3Exit state after a host-initiated resume. If it's a device
* initiated remote wake, don't pass up the link state change,
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 652dc36..9334cde 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -452,6 +452,14 @@
*/
#define XHCI_DEFAULT_BESL 4
+/*
+ * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
+ * to complete link training. usually link trainig completes much faster
+ * so check status 10 times with 36ms sleep in places we need to wait for
+ * polling to complete.
+ */
+#define XHCI_PORT_POLLING_LFPS_TIME 36
+
/**
* struct xhci_intr_reg - Interrupt Register Set
* @irq_pending: IMAN - Interrupt Management Register. Used to enable
diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c
index 4d72b7d..0468484 100644
--- a/drivers/usb/misc/usb251xb.c
+++ b/drivers/usb/misc/usb251xb.c
@@ -547,7 +547,7 @@
*/
hub->port_swap = USB251XB_DEF_PORT_SWAP;
of_property_for_each_u32(np, "swap-dx-lanes", prop, p, port) {
- if ((port >= 0) && (port <= data->port_cnt))
+ if (port <= data->port_cnt)
hub->port_swap |= BIT(port);
}
@@ -612,7 +612,7 @@
dev);
int err;
- if (np) {
+ if (np && of_id) {
err = usb251xb_get_ofdata(hub,
(struct usb251xb_data *)of_id->data);
if (err) {
diff --git a/drivers/usb/mtu3/Kconfig b/drivers/usb/mtu3/Kconfig
index bcc2348..928c2cd6 100644
--- a/drivers/usb/mtu3/Kconfig
+++ b/drivers/usb/mtu3/Kconfig
@@ -6,6 +6,7 @@
tristate "MediaTek USB3 Dual Role controller"
depends on USB || USB_GADGET
depends on ARCH_MEDIATEK || COMPILE_TEST
+ depends on EXTCON || !EXTCON
select USB_XHCI_MTK if USB_SUPPORT && USB_XHCI_HCD
help
Say Y or M here if your system runs on MediaTek SoCs with
diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index fffe23a..979bef9 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -80,6 +80,7 @@
{ USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
{ USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
{ USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
+ { USB_DEVICE(0x10C4, 0x8056) }, /* Lorenz Messtechnik devices */
{ USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
{ USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
{ USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 8f5b174..1d8461a 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -609,6 +609,8 @@
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(FTDI_VID, FTDI_NT_ORIONLXM_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NT_ORIONLX_PLUS_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_NT_ORION_IO_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SYNAPSE_SS200_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CUSTOMWARE_MINIPLEX_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CUSTOMWARE_MINIPLEX2_PID) },
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index b863bed..5755f0d 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -567,7 +567,9 @@
/*
* NovaTech product ids (FTDI_VID)
*/
-#define FTDI_NT_ORIONLXM_PID 0x7c90 /* OrionLXm Substation Automation Platform */
+#define FTDI_NT_ORIONLXM_PID 0x7c90 /* OrionLXm Substation Automation Platform */
+#define FTDI_NT_ORIONLX_PLUS_PID 0x7c91 /* OrionLX+ Substation Automation Platform */
+#define FTDI_NT_ORION_IO_PID 0x7c92 /* Orion I/O */
/*
* Synapse Wireless product ids (FTDI_VID)
diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c
index fc52ac7..18110225 100644
--- a/drivers/usb/serial/mos7720.c
+++ b/drivers/usb/serial/mos7720.c
@@ -366,8 +366,6 @@
if (!urbtrack)
return -ENOMEM;
- kref_get(&mos_parport->ref_count);
- urbtrack->mos_parport = mos_parport;
urbtrack->urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!urbtrack->urb) {
kfree(urbtrack);
@@ -388,6 +386,8 @@
usb_sndctrlpipe(usbdev, 0),
(unsigned char *)urbtrack->setup,
NULL, 0, async_complete, urbtrack);
+ kref_get(&mos_parport->ref_count);
+ urbtrack->mos_parport = mos_parport;
kref_init(&urbtrack->ref_count);
INIT_LIST_HEAD(&urbtrack->urblist_entry);
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 11b21d9..8386906 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -246,6 +246,7 @@
#define QUECTEL_PRODUCT_EC25 0x0125
#define QUECTEL_PRODUCT_BG96 0x0296
#define QUECTEL_PRODUCT_EP06 0x0306
+#define QUECTEL_PRODUCT_EM12 0x0512
#define CMOTECH_VENDOR_ID 0x16d8
#define CMOTECH_PRODUCT_6001 0x6001
@@ -1066,7 +1067,8 @@
.driver_info = RSVD(3) },
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x0023)}, /* ONYX 3G device */
- { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */
+ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000), /* SIMCom SIM5218 */
+ .driver_info = NCTRL(0) | NCTRL(1) | NCTRL(2) | NCTRL(3) | RSVD(4) },
/* Quectel products using Qualcomm vendor ID */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, QUECTEL_PRODUCT_UC15)},
{ USB_DEVICE(QUALCOMM_VENDOR_ID, QUECTEL_PRODUCT_UC20),
@@ -1087,6 +1089,9 @@
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0xff, 0xff),
.driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
+ { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0xff, 0xff),
+ .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
+ { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0, 0) },
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6003),
@@ -1940,10 +1945,12 @@
.driver_info = RSVD(4) },
{ USB_DEVICE_INTERFACE_CLASS(0x2001, 0x7e35, 0xff), /* D-Link DWM-222 */
.driver_info = RSVD(4) },
- { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x7e11, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/A3 */
- { USB_DEVICE_INTERFACE_CLASS(0x2020, 0x4000, 0xff) }, /* OLICARD300 - MT6225 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */
+ { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x7e11, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/A3 */
+ { USB_DEVICE_INTERFACE_CLASS(0x2020, 0x2031, 0xff), /* Olicard 600 */
+ .driver_info = RSVD(4) },
+ { USB_DEVICE_INTERFACE_CLASS(0x2020, 0x4000, 0xff) }, /* OLICARD300 - MT6225 */
{ USB_DEVICE(INOVIA_VENDOR_ID, INOVIA_SEW858) },
{ USB_DEVICE(VIATELECOM_VENDOR_ID, VIATELECOM_PRODUCT_CDS7) },
{ USB_DEVICE_AND_INTERFACE_INFO(WETELECOM_VENDOR_ID, WETELECOM_PRODUCT_WMD200, 0xff, 0xff, 0xff) },
diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
index 0f62db0..a2233d7 100644
--- a/drivers/usb/typec/tcpm/tcpm.c
+++ b/drivers/usb/typec/tcpm/tcpm.c
@@ -37,6 +37,7 @@
S(SRC_ATTACHED), \
S(SRC_STARTUP), \
S(SRC_SEND_CAPABILITIES), \
+ S(SRC_SEND_CAPABILITIES_TIMEOUT), \
S(SRC_NEGOTIATE_CAPABILITIES), \
S(SRC_TRANSITION_SUPPLY), \
S(SRC_READY), \
@@ -2966,10 +2967,34 @@
/* port->hard_reset_count = 0; */
port->caps_count = 0;
port->pd_capable = true;
- tcpm_set_state_cond(port, hard_reset_state(port),
+ tcpm_set_state_cond(port, SRC_SEND_CAPABILITIES_TIMEOUT,
PD_T_SEND_SOURCE_CAP);
}
break;
+ case SRC_SEND_CAPABILITIES_TIMEOUT:
+ /*
+ * Error recovery for a PD_DATA_SOURCE_CAP reply timeout.
+ *
+ * PD 2.0 sinks are supposed to accept src-capabilities with a
+ * 3.0 header and simply ignore any src PDOs which the sink does
+ * not understand such as PPS but some 2.0 sinks instead ignore
+ * the entire PD_DATA_SOURCE_CAP message, causing contract
+ * negotiation to fail.
+ *
+ * After PD_N_HARD_RESET_COUNT hard-reset attempts, we try
+ * sending src-capabilities with a lower PD revision to
+ * make these broken sinks work.
+ */
+ if (port->hard_reset_count < PD_N_HARD_RESET_COUNT) {
+ tcpm_set_state(port, HARD_RESET_SEND, 0);
+ } else if (port->negotiated_rev > PD_REV20) {
+ port->negotiated_rev--;
+ port->hard_reset_count = 0;
+ tcpm_set_state(port, SRC_SEND_CAPABILITIES, 0);
+ } else {
+ tcpm_set_state(port, hard_reset_state(port), 0);
+ }
+ break;
case SRC_NEGOTIATE_CAPABILITIES:
ret = tcpm_pd_check_request(port);
if (ret < 0) {
diff --git a/drivers/usb/typec/tcpm/wcove.c b/drivers/usb/typec/tcpm/wcove.c
index 423208e..6770afd4 100644
--- a/drivers/usb/typec/tcpm/wcove.c
+++ b/drivers/usb/typec/tcpm/wcove.c
@@ -615,8 +615,13 @@
wcove->dev = &pdev->dev;
wcove->regmap = pmic->regmap;
- irq = regmap_irq_get_virq(pmic->irq_chip_data_chgr,
- platform_get_irq(pdev, 0));
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "Failed to get IRQ: %d\n", irq);
+ return irq;
+ }
+
+ irq = regmap_irq_get_virq(pmic->irq_chip_data_chgr, irq);
if (irq < 0)
return irq;
