| /* fdomain.c -- Future Domain TMC-16x0 SCSI driver |
| * Created: Sun May 3 18:53:19 1992 by faith@cs.unc.edu |
| * Revised: Mon Dec 28 21:59:02 1998 by faith@acm.org |
| * Author: Rickard E. Faith, faith@cs.unc.edu |
| * Copyright 1992-1996, 1998 Rickard E. Faith (faith@acm.org) |
| * Shared IRQ supported added 7/7/2001 Alan Cox <alan@redhat.com> |
| |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2, or (at your option) any |
| * later version. |
| |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| |
| * You should have received a copy of the GNU General Public License along |
| * with this program; if not, write to the Free Software Foundation, Inc., |
| * 675 Mass Ave, Cambridge, MA 02139, USA. |
| |
| ************************************************************************** |
| |
| SUMMARY: |
| |
| Future Domain BIOS versions supported for autodetect: |
| 2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61 |
| Chips are supported: |
| TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70 |
| Boards supported: |
| Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX |
| Future Domain TMC-3260 (PCI) |
| Quantum ISA-200S, ISA-250MG |
| Adaptec AHA-2920A (PCI) [BUT *NOT* AHA-2920C -- use aic7xxx instead] |
| IBM ? |
| LILO/INSMOD command-line options: |
| fdomain=<PORT_BASE>,<IRQ>[,<ADAPTER_ID>] |
| |
| |
| |
| NOTE: |
| |
| The Adaptec AHA-2920C has an Adaptec AIC-7850 chip on it. |
| Use the aic7xxx driver for this board. |
| |
| The Adaptec AHA-2920A has a Future Domain chip on it, so this is the right |
| driver for that card. Unfortunately, the boxes will probably just say |
| "2920", so you'll have to look on the card for a Future Domain logo, or a |
| letter after the 2920. |
| |
| |
| |
| THANKS: |
| |
| Thanks to Adaptec for providing PCI boards for testing. This finally |
| enabled me to test the PCI detection and correct it for PCI boards that do |
| not have a BIOS at a standard ISA location. For PCI boards, LILO/INSMOD |
| command-line options should no longer be needed. --RF 18Nov98 |
| |
| |
| |
| DESCRIPTION: |
| |
| This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680 |
| TMC-1650/1670, and TMC-3260 SCSI host adapters. The 1650 and 1670 have a |
| 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin |
| high-density external connector. The 1670 and 1680 have floppy disk |
| controllers built in. The TMC-3260 is a PCI bus card. |
| |
| Future Domain's older boards are based on the TMC-1800 chip, and this |
| driver was originally written for a TMC-1680 board with the TMC-1800 chip. |
| More recently, boards are being produced with the TMC-18C50 and TMC-18C30 |
| chips. The latest and greatest board may not work with this driver. If |
| you have to patch this driver so that it will recognize your board's BIOS |
| signature, then the driver may fail to function after the board is |
| detected. |
| |
| Please note that the drive ordering that Future Domain implemented in BIOS |
| versions 3.4 and 3.5 is the opposite of the order (currently) used by the |
| rest of the SCSI industry. If you have BIOS version 3.4 or 3.5, and have |
| more than one drive, then the drive ordering will be the reverse of that |
| which you see under DOS. For example, under DOS SCSI ID 0 will be D: and |
| SCSI ID 1 will be C: (the boot device). Under Linux, SCSI ID 0 will be |
| /dev/sda and SCSI ID 1 will be /dev/sdb. The Linux ordering is consistent |
| with that provided by all the other SCSI drivers for Linux. If you want |
| this changed, you will probably have to patch the higher level SCSI code. |
| If you do so, please send me patches that are protected by #ifdefs. |
| |
| If you have a TMC-8xx or TMC-9xx board, then this is not the driver for |
| your board. Please refer to the Seagate driver for more information and |
| possible support. |
| |
| |
| |
| HISTORY: |
| |
| Linux Driver Driver |
| Version Version Date Support/Notes |
| |
| 0.0 3 May 1992 V2.0 BIOS; 1800 chip |
| 0.97 1.9 28 Jul 1992 |
| 0.98.6 3.1 27 Nov 1992 |
| 0.99 3.2 9 Dec 1992 |
| |
| 0.99.3 3.3 10 Jan 1993 V3.0 BIOS |
| 0.99.5 3.5 18 Feb 1993 |
| 0.99.10 3.6 15 May 1993 V3.2 BIOS; 18C50 chip |
| 0.99.11 3.17 3 Jul 1993 (now under RCS) |
| 0.99.12 3.18 13 Aug 1993 |
| 0.99.14 5.6 31 Oct 1993 (reselection code removed) |
| |
| 0.99.15 5.9 23 Jan 1994 V3.4 BIOS (preliminary) |
| 1.0.8/1.1.1 5.15 1 Apr 1994 V3.4 BIOS; 18C30 chip (preliminary) |
| 1.0.9/1.1.3 5.16 7 Apr 1994 V3.4 BIOS; 18C30 chip |
| 1.1.38 5.18 30 Jul 1994 36C70 chip (PCI version of 18C30) |
| 1.1.62 5.20 2 Nov 1994 V3.5 BIOS |
| 1.1.73 5.22 7 Dec 1994 Quantum ISA-200S board; V2.0 BIOS |
| |
| 1.1.82 5.26 14 Jan 1995 V3.5 BIOS; TMC-1610M/MER/MEX board |
| 1.2.10 5.28 5 Jun 1995 Quantum ISA-250MG board; V2.0, V2.01 BIOS |
| 1.3.4 5.31 23 Jun 1995 PCI BIOS-32 detection (preliminary) |
| 1.3.7 5.33 4 Jul 1995 PCI BIOS-32 detection |
| 1.3.28 5.36 17 Sep 1995 V3.61 BIOS; LILO command-line support |
| 1.3.34 5.39 12 Oct 1995 V3.60 BIOS; /proc |
| 1.3.72 5.39 8 Feb 1996 Adaptec AHA-2920 board |
| 1.3.85 5.41 4 Apr 1996 |
| 2.0.12 5.44 8 Aug 1996 Use ID 7 for all PCI cards |
| 2.1.1 5.45 2 Oct 1996 Update ROM accesses for 2.1.x |
| 2.1.97 5.46 23 Apr 1998 Rewritten PCI detection routines [mj] |
| 2.1.11x 5.47 9 Aug 1998 Touched for 8 SCSI disk majors support |
| 5.48 18 Nov 1998 BIOS no longer needed for PCI detection |
| 2.2.0 5.50 28 Dec 1998 Support insmod parameters |
| |
| |
| REFERENCES USED: |
| |
| "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation, |
| 1990. |
| |
| "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain |
| Corporation, January 1992. |
| |
| "LXT SCSI Products: Specifications and OEM Technical Manual (Revision |
| B/September 1991)", Maxtor Corporation, 1991. |
| |
| "7213S product Manual (Revision P3)", Maxtor Corporation, 1992. |
| |
| "Draft Proposed American National Standard: Small Computer System |
| Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109, |
| revision 10h, October 17, 1991) |
| |
| Private communications, Drew Eckhardt (drew@cs.colorado.edu) and Eric |
| Youngdale (ericy@cais.com), 1992. |
| |
| Private communication, Tuong Le (Future Domain Engineering department), |
| 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and |
| TMC-18C30 detection.) |
| |
| Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page |
| 60 (2.39: Disk Partition Table Layout). |
| |
| "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page |
| 6-1. |
| |
| |
| |
| NOTES ON REFERENCES: |
| |
| The Maxtor manuals were free. Maxtor telephone technical support is |
| great! |
| |
| The Future Domain manuals were $25 and $35. They document the chip, not |
| the TMC-16x0 boards, so some information I had to guess at. In 1992, |
| Future Domain sold DOS BIOS source for $250 and the UN*X driver source was |
| $750, but these required a non-disclosure agreement, so even if I could |
| have afforded them, they would *not* have been useful for writing this |
| publically distributable driver. Future Domain technical support has |
| provided some information on the phone and have sent a few useful FAXs. |
| They have been much more helpful since they started to recognize that the |
| word "Linux" refers to an operating system :-). |
| |
| |
| |
| ALPHA TESTERS: |
| |
| There are many other alpha testers that come and go as the driver |
| develops. The people listed here were most helpful in times of greatest |
| need (mostly early on -- I've probably left out a few worthy people in |
| more recent times): |
| |
| Todd Carrico (todd@wutc.wustl.edu), Dan Poirier (poirier@cs.unc.edu ), Ken |
| Corey (kenc@sol.acs.unt.edu), C. de Bruin (bruin@bruin@sterbbs.nl), Sakari |
| Aaltonen (sakaria@vipunen.hit.fi), John Rice (rice@xanth.cs.odu.edu), Brad |
| Yearwood (brad@optilink.com), and Ray Toy (toy@soho.crd.ge.com). |
| |
| Special thanks to Tien-Wan Yang (twyang@cs.uh.edu), who graciously lent me |
| his 18C50-based card for debugging. He is the sole reason that this |
| driver works with the 18C50 chip. |
| |
| Thanks to Dave Newman (dnewman@crl.com) for providing initial patches for |
| the version 3.4 BIOS. |
| |
| Thanks to James T. McKinley (mckinley@msupa.pa.msu.edu) for providing |
| patches that support the TMC-3260, a PCI bus card with the 36C70 chip. |
| The 36C70 chip appears to be "completely compatible" with the 18C30 chip. |
| |
| Thanks to Eric Kasten (tigger@petroglyph.cl.msu.edu) for providing the |
| patch for the version 3.5 BIOS. |
| |
| Thanks for Stephen Henson (shenson@nyx10.cs.du.edu) for providing the |
| patch for the Quantum ISA-200S SCSI adapter. |
| |
| Thanks to Adam Bowen for the signature to the 1610M/MER/MEX scsi cards, to |
| Martin Andrews (andrewm@ccfadm.eeg.ccf.org) for the signature to some |
| random TMC-1680 repackaged by IBM; and to Mintak Ng (mintak@panix.com) for |
| the version 3.61 BIOS signature. |
| |
| Thanks for Mark Singer (elf@netcom.com) and Richard Simpson |
| (rsimpson@ewrcsdra.demon.co.uk) for more Quantum signatures and detective |
| work on the Quantum RAM layout. |
| |
| Special thanks to James T. McKinley (mckinley@msupa.pa.msu.edu) for |
| providing patches for proper PCI BIOS32-mediated detection of the TMC-3260 |
| card (a PCI bus card with the 36C70 chip). Please send James PCI-related |
| bug reports. |
| |
| Thanks to Tom Cavin (tec@usa1.com) for preliminary command-line option |
| patches. |
| |
| New PCI detection code written by Martin Mares <mj@atrey.karlin.mff.cuni.cz> |
| |
| Insmod parameter code based on patches from Daniel Graham |
| <graham@balance.uoregon.edu>. |
| |
| All of the alpha testers deserve much thanks. |
| |
| |
| |
| NOTES ON USER DEFINABLE OPTIONS: |
| |
| DEBUG: This turns on the printing of various debug information. |
| |
| ENABLE_PARITY: This turns on SCSI parity checking. With the current |
| driver, all attached devices must support SCSI parity. If none of your |
| devices support parity, then you can probably get the driver to work by |
| turning this option off. I have no way of testing this, however, and it |
| would appear that no one ever uses this option. |
| |
| FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the |
| 18C30 chip have a 2k cache). When this many 512 byte blocks are filled by |
| the SCSI device, an interrupt will be raised. Therefore, this could be as |
| low as 0, or as high as 16. Note, however, that values which are too high |
| or too low seem to prevent any interrupts from occurring, and thereby lock |
| up the machine. I have found that 2 is a good number, but throughput may |
| be increased by changing this value to values which are close to 2. |
| Please let me know if you try any different values. |
| |
| DO_DETECT: This activates some old scan code which was needed before the |
| high level drivers got fixed. If you are having trouble with the driver, |
| turning this on should not hurt, and might help. Please let me know if |
| this is the case, since this code will be removed from future drivers. |
| |
| RESELECTION: This is no longer an option, since I gave up trying to |
| implement it in version 4.x of this driver. It did not improve |
| performance at all and made the driver unstable (because I never found one |
| of the two race conditions which were introduced by the multiple |
| outstanding command code). The instability seems a very high price to pay |
| just so that you don't have to wait for the tape to rewind. If you want |
| this feature implemented, send me patches. I'll be happy to send a copy |
| of my (broken) driver to anyone who would like to see a copy. |
| |
| **************************************************************************/ |
| |
| #include <linux/module.h> |
| |
| #ifdef PCMCIA |
| #undef MODULE |
| #endif |
| |
| #include <linux/init.h> |
| #include <linux/sched.h> |
| #include <asm/io.h> |
| #include <linux/blk.h> |
| #include "scsi.h" |
| #include "hosts.h" |
| #include "fdomain.h" |
| #include <asm/system.h> |
| #include <linux/spinlock.h> |
| #include <linux/errno.h> |
| #include <linux/string.h> |
| #include <linux/ioport.h> |
| #include <linux/proc_fs.h> |
| #include <linux/pci.h> |
| #include <linux/stat.h> |
| #include <linux/delay.h> |
| |
| #include <linux/config.h> /* for CONFIG_PCI */ |
| |
| #define VERSION "$Revision: 5.50 $" |
| |
| /* START OF USER DEFINABLE OPTIONS */ |
| |
| #define DEBUG 1 /* Enable debugging output */ |
| #define ENABLE_PARITY 1 /* Enable SCSI Parity */ |
| #define FIFO_COUNT 2 /* Number of 512 byte blocks before INTR */ |
| #define DO_DETECT 0 /* Do device detection here (see scsi.c) */ |
| |
| /* END OF USER DEFINABLE OPTIONS */ |
| |
| #if DEBUG |
| #define EVERY_ACCESS 0 /* Write a line on every scsi access */ |
| #define ERRORS_ONLY 1 /* Only write a line if there is an error */ |
| #define DEBUG_DETECT 0 /* Debug fdomain_16x0_detect() */ |
| #define DEBUG_MESSAGES 1 /* Debug MESSAGE IN phase */ |
| #define DEBUG_ABORT 1 /* Debug abort() routine */ |
| #define DEBUG_RESET 1 /* Debug reset() routine */ |
| #define DEBUG_RACE 1 /* Debug interrupt-driven race condition */ |
| #else |
| #define EVERY_ACCESS 0 /* LEAVE THESE ALONE--CHANGE THE ONES ABOVE */ |
| #define ERRORS_ONLY 0 |
| #define DEBUG_DETECT 0 |
| #define DEBUG_MESSAGES 0 |
| #define DEBUG_ABORT 0 |
| #define DEBUG_RESET 0 |
| #define DEBUG_RACE 0 |
| #endif |
| |
| /* Errors are reported on the line, so we don't need to report them again */ |
| #if EVERY_ACCESS |
| #undef ERRORS_ONLY |
| #define ERRORS_ONLY 0 |
| #endif |
| |
| #if ENABLE_PARITY |
| #define PARITY_MASK 0x08 |
| #else |
| #define PARITY_MASK 0x00 |
| #endif |
| |
| enum chip_type { |
| unknown = 0x00, |
| tmc1800 = 0x01, |
| tmc18c50 = 0x02, |
| tmc18c30 = 0x03, |
| }; |
| |
| enum { |
| in_arbitration = 0x02, |
| in_selection = 0x04, |
| in_other = 0x08, |
| disconnect = 0x10, |
| aborted = 0x20, |
| sent_ident = 0x40, |
| }; |
| |
| enum in_port_type { |
| Read_SCSI_Data = 0, |
| SCSI_Status = 1, |
| TMC_Status = 2, |
| FIFO_Status = 3, /* tmc18c50/tmc18c30 only */ |
| Interrupt_Cond = 4, /* tmc18c50/tmc18c30 only */ |
| LSB_ID_Code = 5, |
| MSB_ID_Code = 6, |
| Read_Loopback = 7, |
| SCSI_Data_NoACK = 8, |
| Interrupt_Status = 9, |
| Configuration1 = 10, |
| Configuration2 = 11, /* tmc18c50/tmc18c30 only */ |
| Read_FIFO = 12, |
| FIFO_Data_Count = 14 |
| }; |
| |
| enum out_port_type { |
| Write_SCSI_Data = 0, |
| SCSI_Cntl = 1, |
| Interrupt_Cntl = 2, |
| SCSI_Mode_Cntl = 3, |
| TMC_Cntl = 4, |
| Memory_Cntl = 5, /* tmc18c50/tmc18c30 only */ |
| Write_Loopback = 7, |
| IO_Control = 11, /* tmc18c30 only */ |
| Write_FIFO = 12 |
| }; |
| |
| /* .bss will zero all the static variables below */ |
| static int port_base; |
| static unsigned long bios_base; |
| static int bios_major; |
| static int bios_minor; |
| static int PCI_bus; |
| static int Quantum; /* Quantum board variant */ |
| static int interrupt_level; |
| static volatile int in_command; |
| static Scsi_Cmnd *current_SC; |
| static enum chip_type chip = unknown; |
| static int adapter_mask; |
| static int this_id; |
| static int setup_called; |
| |
| #if DEBUG_RACE |
| static volatile int in_interrupt_flag; |
| #endif |
| |
| static int SCSI_Mode_Cntl_port; |
| static int FIFO_Data_Count_port; |
| static int Interrupt_Cntl_port; |
| static int Interrupt_Status_port; |
| static int Read_FIFO_port; |
| static int Read_SCSI_Data_port; |
| static int SCSI_Cntl_port; |
| static int SCSI_Data_NoACK_port; |
| static int SCSI_Status_port; |
| static int TMC_Cntl_port; |
| static int TMC_Status_port; |
| static int Write_FIFO_port; |
| static int Write_SCSI_Data_port; |
| |
| static int FIFO_Size = 0x2000; /* 8k FIFO for |
| pre-tmc18c30 chips */ |
| |
| extern void do_fdomain_16x0_intr( int irq, void *dev_id, |
| struct pt_regs * regs ); |
| |
| #ifdef MODULE |
| /* Allow insmod parameters to be like LILO |
| parameters. For example: |
| insmod fdomain fdomain=0x140,11 |
| */ |
| static char * fdomain = NULL; |
| MODULE_PARM(fdomain, "s"); |
| #endif |
| |
| static unsigned long addresses[] = { |
| 0xc8000, |
| 0xca000, |
| 0xce000, |
| 0xde000, |
| 0xcc000, /* Extra addresses for PCI boards */ |
| 0xd0000, |
| 0xe0000, |
| }; |
| #define ADDRESS_COUNT (sizeof( addresses ) / sizeof( unsigned )) |
| |
| static unsigned short ports[] = { 0x140, 0x150, 0x160, 0x170 }; |
| #define PORT_COUNT (sizeof( ports ) / sizeof( unsigned short )) |
| |
| static unsigned short ints[] = { 3, 5, 10, 11, 12, 14, 15, 0 }; |
| |
| /* |
| |
| READ THIS BEFORE YOU ADD A SIGNATURE! |
| |
| READING THIS SHORT NOTE CAN SAVE YOU LOTS OF TIME! |
| |
| READ EVERY WORD, ESPECIALLY THE WORD *NOT* |
| |
| This driver works *ONLY* for Future Domain cards using the TMC-1800, |
| TMC-18C50, or TMC-18C30 chip. This includes models TMC-1650, 1660, 1670, |
| and 1680. These are all 16-bit cards. |
| |
| The following BIOS signature signatures are for boards which do *NOT* |
| work with this driver (these TMC-8xx and TMC-9xx boards may work with the |
| Seagate driver): |
| |
| FUTURE DOMAIN CORP. (C) 1986-1988 V4.0I 03/16/88 |
| FUTURE DOMAIN CORP. (C) 1986-1989 V5.0C2/14/89 |
| FUTURE DOMAIN CORP. (C) 1986-1989 V6.0A7/28/89 |
| FUTURE DOMAIN CORP. (C) 1986-1990 V6.0105/31/90 |
| FUTURE DOMAIN CORP. (C) 1986-1990 V6.0209/18/90 |
| FUTURE DOMAIN CORP. (C) 1986-1990 V7.009/18/90 |
| FUTURE DOMAIN CORP. (C) 1992 V8.00.004/02/92 |
| |
| (The cards which do *NOT* work are all 8-bit cards -- although some of |
| them have a 16-bit form-factor, the upper 8-bits are used only for IRQs |
| and are *NOT* used for data. You can tell the difference by following |
| the tracings on the circuit board -- if only the IRQ lines are involved, |
| you have a "8-bit" card, and should *NOT* use this driver.) |
| |
| */ |
| |
| struct signature { |
| const char *signature; |
| int sig_offset; |
| int sig_length; |
| int major_bios_version; |
| int minor_bios_version; |
| int flag; /* 1 == PCI_bus, 2 == ISA_200S, 3 == ISA_250MG, 4 == ISA_200S */ |
| } signatures[] = { |
| /* 1 2 3 4 5 6 */ |
| /* 123456789012345678901234567890123456789012345678901234567890 */ |
| { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.07/28/89", 5, 50, 2, 0, 0 }, |
| { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V1.07/28/89", 5, 50, 2, 0, 0 }, |
| { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.07/28/89", 72, 50, 2, 0, 2 }, |
| { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.0", 73, 43, 2, 0, 3 }, |
| { "FUTURE DOMAIN CORP. (C) 1991 1800-V2.0.", 72, 39, 2, 0, 4 }, |
| { "FUTURE DOMAIN CORP. (C) 1992 V3.00.004/02/92", 5, 44, 3, 0, 0 }, |
| { "FUTURE DOMAIN TMC-18XX (C) 1993 V3.203/12/93", 5, 44, 3, 2, 0 }, |
| { "IBM F1 P2 BIOS v1.0104/29/93", 5, 28, 3, -1, 0 }, |
| { "Future Domain Corp. V1.0008/18/93", 5, 33, 3, 4, 0 }, |
| { "Future Domain Corp. V1.0008/18/93", 26, 33, 3, 4, 1 }, |
| { "Adaptec AHA-2920 PCI-SCSI Card", 42, 31, 3, -1, 1 }, |
| { "IBM F1 P264/32", 5, 14, 3, -1, 1 }, |
| /* This next signature may not be a 3.5 bios */ |
| { "Future Domain Corp. V2.0108/18/93", 5, 33, 3, 5, 0 }, |
| { "FUTURE DOMAIN CORP. V3.5008/18/93", 5, 34, 3, 5, 0 }, |
| { "FUTURE DOMAIN 18c30/18c50/1800 (C) 1994 V3.5", 5, 44, 3, 5, 0 }, |
| { "FUTURE DOMAIN CORP. V3.6008/18/93", 5, 34, 3, 6, 0 }, |
| { "FUTURE DOMAIN CORP. V3.6108/18/93", 5, 34, 3, 6, 0 }, |
| { "FUTURE DOMAIN TMC-18XX", 5, 22, -1, -1, 0 }, |
| |
| /* READ NOTICE ABOVE *BEFORE* YOU WASTE YOUR TIME ADDING A SIGNATURE |
| Also, fix the disk geometry code for your signature and send your |
| changes for faith@cs.unc.edu. Above all, do *NOT* change any old |
| signatures! |
| |
| Note that the last line will match a "generic" 18XX bios. Because |
| Future Domain has changed the host SCSI ID and/or the location of the |
| geometry information in the on-board RAM area for each of the first |
| three BIOS's, it is still important to enter a fully qualified |
| signature in the table for any new BIOS's (after the host SCSI ID and |
| geometry location are verified). */ |
| }; |
| |
| #define SIGNATURE_COUNT (sizeof( signatures ) / sizeof( struct signature )) |
| |
| static void print_banner( struct Scsi_Host *shpnt ) |
| { |
| if (!shpnt) return; /* This won't ever happen */ |
| |
| if (bios_major < 0 && bios_minor < 0) { |
| printk( "scsi%d: <fdomain> No BIOS; using scsi id %d\n", |
| shpnt->host_no, shpnt->this_id ); |
| } else { |
| printk( "scsi%d: <fdomain> BIOS version ", shpnt->host_no ); |
| |
| if (bios_major >= 0) printk( "%d.", bios_major ); |
| else printk( "?." ); |
| |
| if (bios_minor >= 0) printk( "%d", bios_minor ); |
| else printk( "?." ); |
| |
| printk( " at 0x%lx using scsi id %d\n", |
| bios_base, shpnt->this_id ); |
| } |
| |
| /* If this driver works for later FD PCI |
| boards, we will have to modify banner |
| for additional PCI cards, but for now if |
| it's PCI it's a TMC-3260 - JTM */ |
| printk( "scsi%d: <fdomain> %s chip at 0x%x irq ", |
| shpnt->host_no, |
| chip == tmc1800 ? "TMC-1800" |
| : (chip == tmc18c50 ? "TMC-18C50" |
| : (chip == tmc18c30 ? |
| (PCI_bus ? "TMC-36C70 (PCI bus)" : "TMC-18C30") |
| : "Unknown")), |
| port_base ); |
| |
| if (interrupt_level) printk( "%d", interrupt_level ); |
| else printk( "<none>" ); |
| |
| printk( "\n" ); |
| } |
| |
| static int __init fdomain_setup( char *str ) |
| { |
| int ints[4]; |
| |
| (void)get_options(str, ARRAY_SIZE(ints), ints); |
| |
| if (setup_called++ || ints[0] < 2 || ints[0] > 3) { |
| printk( "scsi: <fdomain>" |
| " Usage: fdomain=<PORT_BASE>,<IRQ>[,<ADAPTER_ID>]\n" ); |
| printk( "scsi: <fdomain> Bad LILO/INSMOD parameters?\n" ); |
| return 0; |
| } |
| |
| port_base = ints[0] >= 1 ? ints[1] : 0; |
| interrupt_level = ints[0] >= 2 ? ints[2] : 0; |
| this_id = ints[0] >= 3 ? ints[3] : 0; |
| |
| bios_major = bios_minor = -1; /* Use geometry for BIOS version >= 3.4 */ |
| ++setup_called; |
| return 1; |
| } |
| |
| __setup("fdomain=", fdomain_setup); |
| |
| |
| static void do_pause( unsigned amount ) /* Pause for amount*10 milliseconds */ |
| { |
| mdelay(10*amount); |
| } |
| |
| inline static void fdomain_make_bus_idle( void ) |
| { |
| outb( 0, SCSI_Cntl_port ); |
| outb( 0, SCSI_Mode_Cntl_port ); |
| if (chip == tmc18c50 || chip == tmc18c30) |
| outb( 0x21 | PARITY_MASK, TMC_Cntl_port ); /* Clear forced intr. */ |
| else |
| outb( 0x01 | PARITY_MASK, TMC_Cntl_port ); |
| } |
| |
| static int fdomain_is_valid_port( int port ) |
| { |
| #if DEBUG_DETECT |
| printk( " (%x%x),", |
| inb( port + MSB_ID_Code ), inb( port + LSB_ID_Code ) ); |
| #endif |
| |
| /* The MCA ID is a unique id for each MCA compatible board. We |
| are using ISA boards, but Future Domain provides the MCA ID |
| anyway. We can use this ID to ensure that this is a Future |
| Domain TMC-1660/TMC-1680. |
| */ |
| |
| if (inb( port + LSB_ID_Code ) != 0xe9) { /* test for 0x6127 id */ |
| if (inb( port + LSB_ID_Code ) != 0x27) return 0; |
| if (inb( port + MSB_ID_Code ) != 0x61) return 0; |
| chip = tmc1800; |
| } else { /* test for 0xe960 id */ |
| if (inb( port + MSB_ID_Code ) != 0x60) return 0; |
| chip = tmc18c50; |
| |
| /* Try to toggle 32-bit mode. This only |
| works on an 18c30 chip. (User reports |
| say this works, so we should switch to |
| it in the near future.) */ |
| |
| outb( 0x80, port + IO_Control ); |
| if ((inb( port + Configuration2 ) & 0x80) == 0x80) { |
| outb( 0x00, port + IO_Control ); |
| if ((inb( port + Configuration2 ) & 0x80) == 0x00) { |
| chip = tmc18c30; |
| FIFO_Size = 0x800; /* 2k FIFO */ |
| } |
| } |
| /* If that failed, we are an 18c50. */ |
| } |
| |
| return 1; |
| } |
| |
| static int fdomain_test_loopback( void ) |
| { |
| int i; |
| int result; |
| |
| for (i = 0; i < 255; i++) { |
| outb( i, port_base + Write_Loopback ); |
| result = inb( port_base + Read_Loopback ); |
| if (i != result) |
| return 1; |
| } |
| return 0; |
| } |
| |
| /* fdomain_get_irq assumes that we have a valid MCA ID for a |
| TMC-1660/TMC-1680 Future Domain board. Now, check to be sure the |
| bios_base matches these ports. If someone was unlucky enough to have |
| purchased more than one Future Domain board, then they will have to |
| modify this code, as we only detect one board here. [The one with the |
| lowest bios_base.] |
| |
| Note that this routine is only used for systems without a PCI BIOS32 |
| (e.g., ISA bus). For PCI bus systems, this routine will likely fail |
| unless one of the IRQs listed in the ints array is used by the board. |
| Sometimes it is possible to use the computer's BIOS setup screen to |
| configure a PCI system so that one of these IRQs will be used by the |
| Future Domain card. */ |
| |
| static int fdomain_get_irq( int base ) |
| { |
| int options = inb( base + Configuration1 ); |
| |
| #if DEBUG_DETECT |
| printk( "scsi: <fdomain> Options = %x\n", options ); |
| #endif |
| |
| /* Check for board with lowest bios_base -- |
| this isn't valid for the 18c30 or for |
| boards on the PCI bus, so just assume we |
| have the right board. */ |
| |
| if (chip != tmc18c30 |
| && !PCI_bus |
| && addresses[ (options & 0xc0) >> 6 ] != bios_base) return 0; |
| |
| return ints[ (options & 0x0e) >> 1 ]; |
| } |
| |
| static int fdomain_isa_detect( int *irq, int *iobase ) |
| { |
| int i, j; |
| int base = 0xdeadbeef; |
| int flag = 0; |
| |
| #if DEBUG_DETECT |
| printk( "scsi: <fdomain> fdomain_isa_detect:" ); |
| #endif |
| |
| |
| for (i = 0; !bios_base && i < ADDRESS_COUNT; i++) { |
| #if DEBUG_DETECT |
| printk( " %lx(%lx),", addresses[i], bios_base ); |
| #endif |
| for (j = 0; !bios_base && j < SIGNATURE_COUNT; j++) { |
| if (isa_check_signature(addresses[i] + signatures[j].sig_offset, |
| signatures[j].signature, |
| signatures[j].sig_length )) { |
| bios_major = signatures[j].major_bios_version; |
| bios_minor = signatures[j].minor_bios_version; |
| PCI_bus = (signatures[j].flag == 1); |
| Quantum = (signatures[j].flag > 1) ? signatures[j].flag : 0; |
| bios_base = addresses[i]; |
| } |
| } |
| } |
| |
| if (bios_major == 2) { |
| /* The TMC-1660/TMC-1680 has a RAM area just after the BIOS ROM. |
| Assuming the ROM is enabled (otherwise we wouldn't have been |
| able to read the ROM signature :-), then the ROM sets up the |
| RAM area with some magic numbers, such as a list of port |
| base addresses and a list of the disk "geometry" reported to |
| DOS (this geometry has nothing to do with physical geometry). |
| */ |
| |
| switch (Quantum) { |
| case 2: /* ISA_200S */ |
| case 3: /* ISA_250MG */ |
| base = readb(bios_base + 0x1fa2) + (readb(bios_base + 0x1fa3) << 8); |
| break; |
| case 4: /* ISA_200S (another one) */ |
| base = readb(bios_base + 0x1fa3) + (readb(bios_base + 0x1fa4) << 8); |
| break; |
| default: |
| base = readb(bios_base + 0x1fcc) + (readb(bios_base + 0x1fcd) << 8); |
| break; |
| } |
| |
| #if DEBUG_DETECT |
| printk( " %x,", base ); |
| #endif |
| |
| for (flag = 0, i = 0; !flag && i < PORT_COUNT; i++) { |
| if (base == ports[i]) |
| ++flag; |
| } |
| |
| if (flag && fdomain_is_valid_port( base )) { |
| *irq = fdomain_get_irq( base ); |
| *iobase = base; |
| return 1; |
| } |
| |
| /* This is a bad sign. It usually means that someone patched the |
| BIOS signature list (the signatures variable) to contain a BIOS |
| signature for a board *OTHER THAN* the TMC-1660/TMC-1680. */ |
| |
| #if DEBUG_DETECT |
| printk( " RAM FAILED, " ); |
| #endif |
| } |
| |
| /* Anyway, the alternative to finding the address in the RAM is to just |
| search through every possible port address for one that is attached |
| to the Future Domain card. Don't panic, though, about reading all |
| these random port addresses -- there are rumors that the Future |
| Domain BIOS does something very similar. |
| |
| Do not, however, check ports which the kernel knows are being used by |
| another driver. */ |
| |
| for (i = 0; i < PORT_COUNT; i++) { |
| base = ports[i]; |
| if (check_region( base, 0x10 )) { |
| #if DEBUG_DETECT |
| printk( " (%x inuse),", base ); |
| #endif |
| continue; |
| } |
| #if DEBUG_DETECT |
| printk( " %x,", base ); |
| #endif |
| if ((flag = fdomain_is_valid_port( base ))) break; |
| } |
| |
| #if DEBUG_DETECT |
| if (flag) printk( " SUCCESS\n" ); |
| else printk( " FAILURE\n" ); |
| #endif |
| |
| if (!flag) return 0; /* iobase not found */ |
| |
| *irq = fdomain_get_irq( base ); |
| *iobase = base; |
| |
| return 1; /* success */ |
| } |
| |
| /* PCI detection function: int fdomain_pci_bios_detect(int* irq, int* |
| iobase) This function gets the Interrupt Level and I/O base address from |
| the PCI configuration registers. */ |
| |
| #ifdef CONFIG_PCI |
| static int fdomain_pci_bios_detect( int *irq, int *iobase, struct pci_dev **ret_pdev ) |
| { |
| unsigned int pci_irq; /* PCI interrupt line */ |
| unsigned long pci_base; /* PCI I/O base address */ |
| struct pci_dev *pdev = NULL; |
| |
| if (!pci_present()) return 0; |
| |
| #if DEBUG_DETECT |
| /* Tell how to print a list of the known PCI devices from bios32 and |
| list vendor and device IDs being used if in debug mode. */ |
| |
| printk( "scsi: <fdomain> INFO: use lspci -v to see list of PCI devices\n" ); |
| printk( "scsi: <fdomain> TMC-3260 detect:" |
| " Using Vendor ID: 0x%x and Device ID: 0x%x\n", |
| PCI_VENDOR_ID_FD, |
| PCI_DEVICE_ID_FD_36C70 ); |
| #endif |
| |
| if ((pdev = pci_find_device(PCI_VENDOR_ID_FD, |
| PCI_DEVICE_ID_FD_36C70, |
| pdev)) == NULL) |
| return 0; |
| if (pci_enable_device(pdev)) return 0; |
| |
| #if DEBUG_DETECT |
| printk( "scsi: <fdomain> TMC-3260 detect:" |
| " PCI bus %u, device %u, function %u\n", |
| pdev->bus->number, |
| PCI_SLOT(pdev->devfn), |
| PCI_FUNC(pdev->devfn)); |
| #endif |
| |
| /* We now have the appropriate device function for the FD board so we |
| just read the PCI config info from the registers. */ |
| |
| pci_base = pci_resource_start(pdev, 0); |
| pci_irq = pdev->irq; |
| |
| /* Now we have the I/O base address and interrupt from the PCI |
| configuration registers. */ |
| |
| *irq = pci_irq; |
| *iobase = pci_base; |
| *ret_pdev = pdev; |
| |
| #if DEBUG_DETECT |
| printk( "scsi: <fdomain> TMC-3260 detect:" |
| " IRQ = %d, I/O base = 0x%x [0x%lx]\n", *irq, *iobase, pci_base ); |
| #endif |
| |
| if (!fdomain_is_valid_port( *iobase )) { |
| printk( "scsi: <fdomain>" |
| " PCI card detected, but driver not loaded (invalid port)\n" ); |
| return 0; |
| } |
| |
| /* Fill in a few global variables. Ugh. */ |
| bios_major = bios_minor = -1; |
| PCI_bus = 1; |
| Quantum = 0; |
| bios_base = 0; |
| |
| return 1; |
| } |
| #endif |
| |
| int fdomain_16x0_detect( Scsi_Host_Template *tpnt ) |
| { |
| int retcode; |
| struct Scsi_Host *shpnt; |
| struct pci_dev *pdev = NULL; |
| #if DO_DETECT |
| int i = 0; |
| int j = 0; |
| const int buflen = 255; |
| Scsi_Cmnd SCinit; |
| unsigned char do_inquiry[] = { INQUIRY, 0, 0, 0, buflen, 0 }; |
| unsigned char do_request_sense[] = { REQUEST_SENSE, 0, 0, 0, buflen, 0 }; |
| unsigned char do_read_capacity[] = { READ_CAPACITY, |
| 0, 0, 0, 0, 0, 0, 0, 0, 0 }; |
| unsigned char buf[buflen]; |
| #endif |
| |
| tpnt->proc_name = "fdomain"; |
| |
| #ifdef MODULE |
| if (fdomain) |
| fdomain_setup(fdomain); |
| #endif |
| |
| if (setup_called) { |
| #if DEBUG_DETECT |
| printk( "scsi: <fdomain> No BIOS, using port_base = 0x%x, irq = %d\n", |
| port_base, interrupt_level ); |
| #endif |
| if (!fdomain_is_valid_port( port_base )) { |
| printk( "scsi: <fdomain> Cannot locate chip at port base 0x%x\n", |
| port_base ); |
| printk( "scsi: <fdomain> Bad LILO/INSMOD parameters?\n" ); |
| return 0; |
| } |
| } else { |
| int flag = 0; |
| |
| #ifdef CONFIG_PCI |
| /* Try PCI detection first */ |
| flag = fdomain_pci_bios_detect( &interrupt_level, &port_base, &pdev ); |
| #endif |
| if (!flag) { |
| /* Then try ISA bus detection */ |
| flag = fdomain_isa_detect( &interrupt_level, &port_base ); |
| |
| if (!flag) { |
| printk( "scsi: <fdomain> Detection failed (no card)\n" ); |
| return 0; |
| } |
| } |
| } |
| |
| SCSI_Mode_Cntl_port = port_base + SCSI_Mode_Cntl; |
| FIFO_Data_Count_port = port_base + FIFO_Data_Count; |
| Interrupt_Cntl_port = port_base + Interrupt_Cntl; |
| Interrupt_Status_port = port_base + Interrupt_Status; |
| Read_FIFO_port = port_base + Read_FIFO; |
| Read_SCSI_Data_port = port_base + Read_SCSI_Data; |
| SCSI_Cntl_port = port_base + SCSI_Cntl; |
| SCSI_Data_NoACK_port = port_base + SCSI_Data_NoACK; |
| SCSI_Status_port = port_base + SCSI_Status; |
| TMC_Cntl_port = port_base + TMC_Cntl; |
| TMC_Status_port = port_base + TMC_Status; |
| Write_FIFO_port = port_base + Write_FIFO; |
| Write_SCSI_Data_port = port_base + Write_SCSI_Data; |
| |
| fdomain_16x0_reset( NULL, 0 ); |
| |
| if (fdomain_test_loopback()) { |
| printk( "scsi: <fdomain> Detection failed" |
| " (loopback test failed at port base 0x%x)\n", port_base ); |
| if (setup_called) { |
| printk( "scsi: <fdomain> Bad LILO/INSMOD parameters?\n" ); |
| } |
| return 0; |
| } |
| |
| if (this_id) { |
| tpnt->this_id = (this_id & 0x07); |
| adapter_mask = (1 << tpnt->this_id); |
| } else { |
| if (PCI_bus || (bios_major == 3 && bios_minor >= 2) || bios_major < 0) { |
| tpnt->this_id = 7; |
| adapter_mask = 0x80; |
| } else { |
| tpnt->this_id = 6; |
| adapter_mask = 0x40; |
| } |
| } |
| |
| /* Print out a banner here in case we can't |
| get resources. */ |
| |
| shpnt = scsi_register( tpnt, 0 ); |
| if(shpnt == NULL) |
| return 0; |
| shpnt->irq = interrupt_level; |
| shpnt->io_port = port_base; |
| scsi_set_pci_device(shpnt, pdev); |
| shpnt->n_io_port = 0x10; |
| print_banner( shpnt ); |
| |
| /* Log IRQ with kernel */ |
| if (!interrupt_level) { |
| printk( "scsi: <fdomain>" |
| " Card Detected, but driver not loaded (no IRQ)\n" ); |
| return 0; |
| } else { |
| /* Register the IRQ with the kernel */ |
| |
| retcode = request_irq( interrupt_level, |
| do_fdomain_16x0_intr, pdev?SA_SHIRQ:0, "fdomain", shpnt); |
| |
| if (retcode < 0) { |
| if (retcode == -EINVAL) { |
| printk( "scsi: <fdomain> IRQ %d is bad!\n", interrupt_level ); |
| printk( " This shouldn't happen!\n" ); |
| printk( " Send mail to faith@acm.org\n" ); |
| } else if (retcode == -EBUSY) { |
| printk( "scsi: <fdomain> IRQ %d is already in use!\n", |
| interrupt_level ); |
| printk( " Please use another IRQ!\n" ); |
| } else { |
| printk( "scsi: <fdomain> Error getting IRQ %d\n", |
| interrupt_level ); |
| printk( " This shouldn't happen!\n" ); |
| printk( " Send mail to faith@acm.org\n" ); |
| } |
| printk( "scsi: <fdomain> Detected, but driver not loaded (IRQ)\n" ); |
| return 0; |
| } |
| } |
| |
| /* Log I/O ports with kernel */ |
| request_region( port_base, 0x10, "fdomain" ); |
| |
| #if DO_DETECT |
| |
| /* These routines are here because of the way the SCSI bus behaves after |
| a reset. This appropriate behavior was not handled correctly by the |
| higher level SCSI routines when I first wrote this driver. Now, |
| however, correct scan routines are part of scsi.c and these routines |
| are no longer needed. However, this code is still good for |
| debugging. */ |
| |
| SCinit.request_buffer = SCinit.buffer = buf; |
| SCinit.request_bufflen = SCinit.bufflen = sizeof(buf)-1; |
| SCinit.use_sg = 0; |
| SCinit.lun = 0; |
| |
| printk( "scsi: <fdomain> detection routine scanning for devices:\n" ); |
| for (i = 0; i < 8; i++) { |
| SCinit.target = i; |
| if (i == tpnt->this_id) /* Skip host adapter */ |
| continue; |
| memcpy(SCinit.cmnd, do_request_sense, sizeof(do_request_sense)); |
| retcode = fdomain_16x0_command(&SCinit); |
| if (!retcode) { |
| memcpy(SCinit.cmnd, do_inquiry, sizeof(do_inquiry)); |
| retcode = fdomain_16x0_command(&SCinit); |
| if (!retcode) { |
| printk( " SCSI ID %d: ", i ); |
| for (j = 8; j < (buf[4] < 32 ? buf[4] : 32); j++) |
| printk( "%c", buf[j] >= 20 ? buf[j] : ' ' ); |
| memcpy(SCinit.cmnd, do_read_capacity, sizeof(do_read_capacity)); |
| retcode = fdomain_16x0_command(&SCinit); |
| if (!retcode) { |
| unsigned long blocks, size, capacity; |
| |
| blocks = (buf[0] << 24) | (buf[1] << 16) |
| | (buf[2] << 8) | buf[3]; |
| size = (buf[4] << 24) | (buf[5] << 16) | (buf[6] << 8) | buf[7]; |
| capacity = +( +(blocks / 1024L) * +(size * 10L)) / 1024L; |
| |
| printk( "%lu MB (%lu byte blocks)", |
| ((capacity + 5L) / 10L), size ); |
| } else { |
| memcpy(SCinit.cmnd, do_request_sense, sizeof(do_request_sense)); |
| retcode = fdomain_16x0_command(&SCinit); |
| } |
| printk ("\n" ); |
| } else { |
| memcpy(SCinit.cmnd, do_request_sense, sizeof(do_request_sense)); |
| retcode = fdomain_16x0_command(&SCinit); |
| } |
| } |
| } |
| #endif |
| |
| return 1; /* Maximum of one adapter will be detected. */ |
| } |
| |
| const char *fdomain_16x0_info( struct Scsi_Host *ignore ) |
| { |
| static char buffer[128]; |
| char *pt; |
| |
| strcpy( buffer, "Future Domain 16-bit SCSI Driver Version" ); |
| if (strchr( VERSION, ':')) { /* Assume VERSION is an RCS Revision string */ |
| strcat( buffer, strchr( VERSION, ':' ) + 1 ); |
| pt = strrchr( buffer, '$') - 1; |
| if (!pt) /* Stripped RCS Revision string? */ |
| pt = buffer + strlen( buffer ) - 1; |
| if (*pt != ' ') |
| ++pt; |
| *pt = '\0'; |
| } else { /* Assume VERSION is a number */ |
| strcat( buffer, " " VERSION ); |
| } |
| |
| return buffer; |
| } |
| |
| /* First pass at /proc information routine. */ |
| /* |
| * inout : decides on the direction of the dataflow and the meaning of the |
| * variables |
| * buffer: If inout==FALSE data is being written to it else read from it |
| * *start: If inout==FALSE start of the valid data in the buffer |
| * offset: If inout==FALSE offset from the beginning of the imaginary file |
| * from which we start writing into the buffer |
| * length: If inout==FALSE max number of bytes to be written into the buffer |
| * else number of bytes in the buffer |
| */ |
| int fdomain_16x0_proc_info( char *buffer, char **start, off_t offset, |
| int length, int hostno, int inout ) |
| { |
| const char *info = fdomain_16x0_info( NULL ); |
| int len; |
| int pos; |
| int begin; |
| |
| if (inout) return(-ENOSYS); |
| |
| begin = 0; |
| strcpy( buffer, info ); |
| strcat( buffer, "\n" ); |
| |
| pos = len = strlen( buffer ); |
| |
| if(pos < offset) { |
| len = 0; |
| begin = pos; |
| } |
| |
| *start = buffer + (offset - begin); /* Start of wanted data */ |
| len -= (offset - begin); |
| if(len > length) len = length; |
| |
| return(len); |
| } |
| |
| #if 0 |
| static int fdomain_arbitrate( void ) |
| { |
| int status = 0; |
| unsigned long timeout; |
| |
| #if EVERY_ACCESS |
| printk( "fdomain_arbitrate()\n" ); |
| #endif |
| |
| outb( 0x00, SCSI_Cntl_port ); /* Disable data drivers */ |
| outb( adapter_mask, port_base + SCSI_Data_NoACK ); /* Set our id bit */ |
| outb( 0x04 | PARITY_MASK, TMC_Cntl_port ); /* Start arbitration */ |
| |
| timeout = 500; |
| do { |
| status = inb( TMC_Status_port ); /* Read adapter status */ |
| if (status & 0x02) /* Arbitration complete */ |
| return 0; |
| mdelay(1); /* Wait one millisecond */ |
| } while (--timeout); |
| |
| /* Make bus idle */ |
| fdomain_make_bus_idle(); |
| |
| #if EVERY_ACCESS |
| printk( "Arbitration failed, status = %x\n", status ); |
| #endif |
| #if ERRORS_ONLY |
| printk( "scsi: <fdomain> Arbitration failed, status = %x\n", status ); |
| #endif |
| return 1; |
| } |
| #endif |
| |
| static int fdomain_select( int target ) |
| { |
| int status; |
| unsigned long timeout; |
| static int flag = 0; |
| |
| |
| outb( 0x82, SCSI_Cntl_port ); /* Bus Enable + Select */ |
| outb( adapter_mask | (1 << target), SCSI_Data_NoACK_port ); |
| |
| /* Stop arbitration and enable parity */ |
| outb( PARITY_MASK, TMC_Cntl_port ); |
| |
| timeout = 350; /* 350 msec */ |
| |
| do { |
| status = inb( SCSI_Status_port ); /* Read adapter status */ |
| if (status & 1) { /* Busy asserted */ |
| /* Enable SCSI Bus (on error, should make bus idle with 0) */ |
| outb( 0x80, SCSI_Cntl_port ); |
| return 0; |
| } |
| mdelay(1); /* wait one msec */ |
| } while (--timeout); |
| /* Make bus idle */ |
| fdomain_make_bus_idle(); |
| #if EVERY_ACCESS |
| if (!target) printk( "Selection failed\n" ); |
| #endif |
| #if ERRORS_ONLY |
| if (!target) { |
| if (!flag) /* Skip first failure for all chips. */ |
| ++flag; |
| else |
| printk( "scsi: <fdomain> Selection failed\n" ); |
| } |
| #endif |
| return 1; |
| } |
| |
| void my_done( int error ) |
| { |
| if (in_command) { |
| in_command = 0; |
| outb( 0x00, Interrupt_Cntl_port ); |
| fdomain_make_bus_idle(); |
| current_SC->result = error; |
| if (current_SC->scsi_done) |
| current_SC->scsi_done( current_SC ); |
| else panic( "scsi: <fdomain> current_SC->scsi_done() == NULL" ); |
| } else { |
| panic( "scsi: <fdomain> my_done() called outside of command\n" ); |
| } |
| #if DEBUG_RACE |
| in_interrupt_flag = 0; |
| #endif |
| } |
| |
| void do_fdomain_16x0_intr( int irq, void *dev_id, struct pt_regs * regs ) |
| { |
| unsigned long flags; |
| int status; |
| int done = 0; |
| unsigned data_count; |
| |
| /* The fdomain_16x0_intr is only called via |
| the interrupt handler. The goal of the |
| sti() here is to allow other |
| interruptions while this routine is |
| running. */ |
| |
| /* Check for other IRQ sources */ |
| if((inb(TMC_Status_port)&0x01)==0) |
| return; |
| |
| /* It is our IRQ */ |
| outb( 0x00, Interrupt_Cntl_port ); |
| |
| /* We usually have one spurious interrupt after each command. Ignore it. */ |
| if (!in_command || !current_SC) { /* Spurious interrupt */ |
| #if EVERY_ACCESS |
| printk( "Spurious interrupt, in_command = %d, current_SC = %x\n", |
| in_command, current_SC ); |
| #endif |
| return; |
| } |
| |
| /* Abort calls my_done, so we do nothing here. */ |
| if (current_SC->SCp.phase & aborted) { |
| #if DEBUG_ABORT |
| printk( "scsi: <fdomain> Interrupt after abort, ignoring\n" ); |
| #endif |
| /* |
| return; */ |
| } |
| |
| #if DEBUG_RACE |
| ++in_interrupt_flag; |
| #endif |
| |
| if (current_SC->SCp.phase & in_arbitration) { |
| status = inb( TMC_Status_port ); /* Read adapter status */ |
| if (!(status & 0x02)) { |
| #if EVERY_ACCESS |
| printk( " AFAIL " ); |
| #endif |
| spin_lock_irqsave(current_SC->host->host_lock, flags); |
| my_done( DID_BUS_BUSY << 16 ); |
| spin_unlock_irqrestore(current_SC->host->host_lock, flags); |
| return; |
| } |
| current_SC->SCp.phase = in_selection; |
| |
| outb( 0x40 | FIFO_COUNT, Interrupt_Cntl_port ); |
| |
| outb( 0x82, SCSI_Cntl_port ); /* Bus Enable + Select */ |
| outb( adapter_mask | (1 << current_SC->target), SCSI_Data_NoACK_port ); |
| |
| /* Stop arbitration and enable parity */ |
| outb( 0x10 | PARITY_MASK, TMC_Cntl_port ); |
| #if DEBUG_RACE |
| in_interrupt_flag = 0; |
| #endif |
| return; |
| } else if (current_SC->SCp.phase & in_selection) { |
| status = inb( SCSI_Status_port ); |
| if (!(status & 0x01)) { |
| /* Try again, for slow devices */ |
| if (fdomain_select( current_SC->target )) { |
| #if EVERY_ACCESS |
| printk( " SFAIL " ); |
| #endif |
| spin_lock_irqsave(current_SC->host->host_lock, flags); |
| my_done( DID_NO_CONNECT << 16 ); |
| spin_unlock_irqrestore(current_SC->host->host_lock, flags); |
| return; |
| } else { |
| #if EVERY_ACCESS |
| printk( " AltSel " ); |
| #endif |
| /* Stop arbitration and enable parity */ |
| outb( 0x10 | PARITY_MASK, TMC_Cntl_port ); |
| } |
| } |
| current_SC->SCp.phase = in_other; |
| outb( 0x90 | FIFO_COUNT, Interrupt_Cntl_port ); |
| outb( 0x80, SCSI_Cntl_port ); |
| #if DEBUG_RACE |
| in_interrupt_flag = 0; |
| #endif |
| return; |
| } |
| |
| /* current_SC->SCp.phase == in_other: this is the body of the routine */ |
| |
| status = inb( SCSI_Status_port ); |
| |
| if (status & 0x10) { /* REQ */ |
| |
| switch (status & 0x0e) { |
| |
| case 0x08: /* COMMAND OUT */ |
| outb( current_SC->cmnd[current_SC->SCp.sent_command++], |
| Write_SCSI_Data_port ); |
| #if EVERY_ACCESS |
| printk( "CMD = %x,", |
| current_SC->cmnd[ current_SC->SCp.sent_command - 1] ); |
| #endif |
| break; |
| case 0x00: /* DATA OUT -- tmc18c50/tmc18c30 only */ |
| if (chip != tmc1800 && !current_SC->SCp.have_data_in) { |
| current_SC->SCp.have_data_in = -1; |
| outb( 0xd0 | PARITY_MASK, TMC_Cntl_port ); |
| } |
| break; |
| case 0x04: /* DATA IN -- tmc18c50/tmc18c30 only */ |
| if (chip != tmc1800 && !current_SC->SCp.have_data_in) { |
| current_SC->SCp.have_data_in = 1; |
| outb( 0x90 | PARITY_MASK, TMC_Cntl_port ); |
| } |
| break; |
| case 0x0c: /* STATUS IN */ |
| current_SC->SCp.Status = inb( Read_SCSI_Data_port ); |
| #if EVERY_ACCESS |
| printk( "Status = %x, ", current_SC->SCp.Status ); |
| #endif |
| #if ERRORS_ONLY |
| if (current_SC->SCp.Status |
| && current_SC->SCp.Status != 2 |
| && current_SC->SCp.Status != 8) { |
| printk( "scsi: <fdomain> target = %d, command = %x, status = %x\n", |
| current_SC->target, |
| current_SC->cmnd[0], |
| current_SC->SCp.Status ); |
| } |
| #endif |
| break; |
| case 0x0a: /* MESSAGE OUT */ |
| outb( MESSAGE_REJECT, Write_SCSI_Data_port ); /* Reject */ |
| break; |
| case 0x0e: /* MESSAGE IN */ |
| current_SC->SCp.Message = inb( Read_SCSI_Data_port ); |
| #if EVERY_ACCESS |
| printk( "Message = %x, ", current_SC->SCp.Message ); |
| #endif |
| if (!current_SC->SCp.Message) ++done; |
| #if DEBUG_MESSAGES || EVERY_ACCESS |
| if (current_SC->SCp.Message) { |
| printk( "scsi: <fdomain> message = %x\n", |
| current_SC->SCp.Message ); |
| } |
| #endif |
| break; |
| } |
| } |
| |
| if (chip == tmc1800 |
| && !current_SC->SCp.have_data_in |
| && (current_SC->SCp.sent_command |
| >= current_SC->cmd_len)) { |
| /* We have to get the FIFO direction |
| correct, so I've made a table based |
| on the SCSI Standard of which commands |
| appear to require a DATA OUT phase. |
| */ |
| /* |
| p. 94: Command for all device types |
| CHANGE DEFINITION 40 DATA OUT |
| COMPARE 39 DATA OUT |
| COPY 18 DATA OUT |
| COPY AND VERIFY 3a DATA OUT |
| INQUIRY 12 |
| LOG SELECT 4c DATA OUT |
| LOG SENSE 4d |
| MODE SELECT (6) 15 DATA OUT |
| MODE SELECT (10) 55 DATA OUT |
| MODE SENSE (6) 1a |
| MODE SENSE (10) 5a |
| READ BUFFER 3c |
| RECEIVE DIAGNOSTIC RESULTS 1c |
| REQUEST SENSE 03 |
| SEND DIAGNOSTIC 1d DATA OUT |
| TEST UNIT READY 00 |
| WRITE BUFFER 3b DATA OUT |
| |
| p.178: Commands for direct-access devices (not listed on p. 94) |
| FORMAT UNIT 04 DATA OUT |
| LOCK-UNLOCK CACHE 36 |
| PRE-FETCH 34 |
| PREVENT-ALLOW MEDIUM REMOVAL 1e |
| READ (6)/RECEIVE 08 |
| READ (10) 3c |
| READ CAPACITY 25 |
| READ DEFECT DATA (10) 37 |
| READ LONG 3e |
| REASSIGN BLOCKS 07 DATA OUT |
| RELEASE 17 |
| RESERVE 16 DATA OUT |
| REZERO UNIT/REWIND 01 |
| SEARCH DATA EQUAL (10) 31 DATA OUT |
| SEARCH DATA HIGH (10) 30 DATA OUT |
| SEARCH DATA LOW (10) 32 DATA OUT |
| SEEK (6) 0b |
| SEEK (10) 2b |
| SET LIMITS (10) 33 |
| START STOP UNIT 1b |
| SYNCHRONIZE CACHE 35 |
| VERIFY (10) 2f |
| WRITE (6)/PRINT/SEND 0a DATA OUT |
| WRITE (10)/SEND 2a DATA OUT |
| WRITE AND VERIFY (10) 2e DATA OUT |
| WRITE LONG 3f DATA OUT |
| WRITE SAME 41 DATA OUT ? |
| |
| p. 261: Commands for sequential-access devices (not previously listed) |
| ERASE 19 |
| LOAD UNLOAD 1b |
| LOCATE 2b |
| READ BLOCK LIMITS 05 |
| READ POSITION 34 |
| READ REVERSE 0f |
| RECOVER BUFFERED DATA 14 |
| SPACE 11 |
| WRITE FILEMARKS 10 ? |
| |
| p. 298: Commands for printer devices (not previously listed) |
| ****** NOT SUPPORTED BY THIS DRIVER, since 0b is SEEK (6) ***** |
| SLEW AND PRINT 0b DATA OUT -- same as seek |
| STOP PRINT 1b |
| SYNCHRONIZE BUFFER 10 |
| |
| p. 315: Commands for processor devices (not previously listed) |
| |
| p. 321: Commands for write-once devices (not previously listed) |
| MEDIUM SCAN 38 |
| READ (12) a8 |
| SEARCH DATA EQUAL (12) b1 DATA OUT |
| SEARCH DATA HIGH (12) b0 DATA OUT |
| SEARCH DATA LOW (12) b2 DATA OUT |
| SET LIMITS (12) b3 |
| VERIFY (12) af |
| WRITE (12) aa DATA OUT |
| WRITE AND VERIFY (12) ae DATA OUT |
| |
| p. 332: Commands for CD-ROM devices (not previously listed) |
| PAUSE/RESUME 4b |
| PLAY AUDIO (10) 45 |
| PLAY AUDIO (12) a5 |
| PLAY AUDIO MSF 47 |
| PLAY TRACK RELATIVE (10) 49 |
| PLAY TRACK RELATIVE (12) a9 |
| READ HEADER 44 |
| READ SUB-CHANNEL 42 |
| READ TOC 43 |
| |
| p. 370: Commands for scanner devices (not previously listed) |
| GET DATA BUFFER STATUS 34 |
| GET WINDOW 25 |
| OBJECT POSITION 31 |
| SCAN 1b |
| SET WINDOW 24 DATA OUT |
| |
| p. 391: Commands for optical memory devices (not listed) |
| ERASE (10) 2c |
| ERASE (12) ac |
| MEDIUM SCAN 38 DATA OUT |
| READ DEFECT DATA (12) b7 |
| READ GENERATION 29 |
| READ UPDATED BLOCK 2d |
| UPDATE BLOCK 3d DATA OUT |
| |
| p. 419: Commands for medium changer devices (not listed) |
| EXCHANGE MEDIUM 46 |
| INITIALIZE ELEMENT STATUS 07 |
| MOVE MEDIUM a5 |
| POSITION TO ELEMENT 2b |
| READ ELEMENT STATUS b8 |
| REQUEST VOL. ELEMENT ADDRESS b5 |
| SEND VOLUME TAG b6 DATA OUT |
| |
| p. 454: Commands for communications devices (not listed previously) |
| GET MESSAGE (6) 08 |
| GET MESSAGE (10) 28 |
| GET MESSAGE (12) a8 |
| */ |
| |
| switch (current_SC->cmnd[0]) { |
| case CHANGE_DEFINITION: case COMPARE: case COPY: |
| case COPY_VERIFY: case LOG_SELECT: case MODE_SELECT: |
| case MODE_SELECT_10: case SEND_DIAGNOSTIC: case WRITE_BUFFER: |
| |
| case FORMAT_UNIT: case REASSIGN_BLOCKS: case RESERVE: |
| case SEARCH_EQUAL: case SEARCH_HIGH: case SEARCH_LOW: |
| case WRITE_6: case WRITE_10: case WRITE_VERIFY: |
| case 0x3f: case 0x41: |
| |
| case 0xb1: case 0xb0: case 0xb2: |
| case 0xaa: case 0xae: |
| |
| case 0x24: |
| |
| case 0x38: case 0x3d: |
| |
| case 0xb6: |
| |
| case 0xea: /* alternate number for WRITE LONG */ |
| |
| current_SC->SCp.have_data_in = -1; |
| outb( 0xd0 | PARITY_MASK, TMC_Cntl_port ); |
| break; |
| |
| case 0x00: |
| default: |
| |
| current_SC->SCp.have_data_in = 1; |
| outb( 0x90 | PARITY_MASK, TMC_Cntl_port ); |
| break; |
| } |
| } |
| |
| if (current_SC->SCp.have_data_in == -1) { /* DATA OUT */ |
| while ( (data_count = FIFO_Size - inw( FIFO_Data_Count_port )) > 512 ) { |
| #if EVERY_ACCESS |
| printk( "DC=%d, ", data_count ) ; |
| #endif |
| if (data_count > current_SC->SCp.this_residual) |
| data_count = current_SC->SCp.this_residual; |
| if (data_count > 0) { |
| #if EVERY_ACCESS |
| printk( "%d OUT, ", data_count ); |
| #endif |
| if (data_count == 1) { |
| outb( *current_SC->SCp.ptr++, Write_FIFO_port ); |
| --current_SC->SCp.this_residual; |
| } else { |
| data_count >>= 1; |
| outsw( Write_FIFO_port, current_SC->SCp.ptr, data_count ); |
| current_SC->SCp.ptr += 2 * data_count; |
| current_SC->SCp.this_residual -= 2 * data_count; |
| } |
| } |
| if (!current_SC->SCp.this_residual) { |
| if (current_SC->SCp.buffers_residual) { |
| --current_SC->SCp.buffers_residual; |
| ++current_SC->SCp.buffer; |
| current_SC->SCp.ptr = current_SC->SCp.buffer->address; |
| current_SC->SCp.this_residual = current_SC->SCp.buffer->length; |
| } else |
| break; |
| } |
| } |
| } |
| |
| if (current_SC->SCp.have_data_in == 1) { /* DATA IN */ |
| while ((data_count = inw( FIFO_Data_Count_port )) > 0) { |
| #if EVERY_ACCESS |
| printk( "DC=%d, ", data_count ); |
| #endif |
| if (data_count > current_SC->SCp.this_residual) |
| data_count = current_SC->SCp.this_residual; |
| if (data_count) { |
| #if EVERY_ACCESS |
| printk( "%d IN, ", data_count ); |
| #endif |
| if (data_count == 1) { |
| *current_SC->SCp.ptr++ = inb( Read_FIFO_port ); |
| --current_SC->SCp.this_residual; |
| } else { |
| data_count >>= 1; /* Number of words */ |
| insw( Read_FIFO_port, current_SC->SCp.ptr, data_count ); |
| current_SC->SCp.ptr += 2 * data_count; |
| current_SC->SCp.this_residual -= 2 * data_count; |
| } |
| } |
| if (!current_SC->SCp.this_residual |
| && current_SC->SCp.buffers_residual) { |
| --current_SC->SCp.buffers_residual; |
| ++current_SC->SCp.buffer; |
| current_SC->SCp.ptr = current_SC->SCp.buffer->address; |
| current_SC->SCp.this_residual = current_SC->SCp.buffer->length; |
| } |
| } |
| } |
| |
| if (done) { |
| #if EVERY_ACCESS |
| printk( " ** IN DONE %d ** ", current_SC->SCp.have_data_in ); |
| #endif |
| |
| #if ERRORS_ONLY |
| if (current_SC->cmnd[0] == REQUEST_SENSE && !current_SC->SCp.Status) { |
| if ((unsigned char)(*((char *)current_SC->request_buffer+2)) & 0x0f) { |
| unsigned char key; |
| unsigned char code; |
| unsigned char qualifier; |
| |
| key = (unsigned char)(*((char *)current_SC->request_buffer + 2)) |
| & 0x0f; |
| code = (unsigned char)(*((char *)current_SC->request_buffer + 12)); |
| qualifier = (unsigned char)(*((char *)current_SC->request_buffer |
| + 13)); |
| |
| if (key != UNIT_ATTENTION |
| && !(key == NOT_READY |
| && code == 0x04 |
| && (!qualifier || qualifier == 0x02 || qualifier == 0x01)) |
| && !(key == ILLEGAL_REQUEST && (code == 0x25 |
| || code == 0x24 |
| || !code))) |
| |
| printk( "scsi: <fdomain> REQUEST SENSE" |
| " Key = %x, Code = %x, Qualifier = %x\n", |
| key, code, qualifier ); |
| } |
| } |
| #endif |
| #if EVERY_ACCESS |
| printk( "BEFORE MY_DONE. . ." ); |
| #endif |
| spin_lock_irqsave(current_SC->host->host_lock, flags); |
| my_done( (current_SC->SCp.Status & 0xff) |
| | ((current_SC->SCp.Message & 0xff) << 8) | (DID_OK << 16) ); |
| spin_unlock_irqrestore(current_SC->host->host_lock, flags); |
| #if EVERY_ACCESS |
| printk( "RETURNING.\n" ); |
| #endif |
| |
| } else { |
| if (current_SC->SCp.phase & disconnect) { |
| outb( 0xd0 | FIFO_COUNT, Interrupt_Cntl_port ); |
| outb( 0x00, SCSI_Cntl_port ); |
| } else { |
| outb( 0x90 | FIFO_COUNT, Interrupt_Cntl_port ); |
| } |
| } |
| #if DEBUG_RACE |
| in_interrupt_flag = 0; |
| #endif |
| return; |
| } |
| |
| int fdomain_16x0_queue( Scsi_Cmnd * SCpnt, void (*done)(Scsi_Cmnd *)) |
| { |
| if (in_command) { |
| panic( "scsi: <fdomain> fdomain_16x0_queue() NOT REENTRANT!\n" ); |
| } |
| #if EVERY_ACCESS |
| printk( "queue: target = %d cmnd = 0x%02x pieces = %d size = %u\n", |
| SCpnt->target, |
| *(unsigned char *)SCpnt->cmnd, |
| SCpnt->use_sg, |
| SCpnt->request_bufflen ); |
| #endif |
| |
| fdomain_make_bus_idle(); |
| |
| current_SC = SCpnt; /* Save this for the done function */ |
| current_SC->scsi_done = done; |
| |
| /* Initialize static data */ |
| |
| if (current_SC->use_sg) { |
| current_SC->SCp.buffer = |
| (struct scatterlist *)current_SC->request_buffer; |
| current_SC->SCp.ptr = current_SC->SCp.buffer->address; |
| current_SC->SCp.this_residual = current_SC->SCp.buffer->length; |
| current_SC->SCp.buffers_residual = current_SC->use_sg - 1; |
| } else { |
| current_SC->SCp.ptr = (char *)current_SC->request_buffer; |
| current_SC->SCp.this_residual = current_SC->request_bufflen; |
| current_SC->SCp.buffer = NULL; |
| current_SC->SCp.buffers_residual = 0; |
| } |
| |
| |
| current_SC->SCp.Status = 0; |
| current_SC->SCp.Message = 0; |
| current_SC->SCp.have_data_in = 0; |
| current_SC->SCp.sent_command = 0; |
| current_SC->SCp.phase = in_arbitration; |
| |
| /* Start arbitration */ |
| outb( 0x00, Interrupt_Cntl_port ); |
| outb( 0x00, SCSI_Cntl_port ); /* Disable data drivers */ |
| outb( adapter_mask, SCSI_Data_NoACK_port ); /* Set our id bit */ |
| ++in_command; |
| outb( 0x20, Interrupt_Cntl_port ); |
| outb( 0x14 | PARITY_MASK, TMC_Cntl_port ); /* Start arbitration */ |
| |
| return 0; |
| } |
| |
| /* The following code, which simulates the old-style command function, was |
| taken from Tommy Thorn's aha1542.c file. This code is Copyright (C) |
| 1992 Tommy Thorn. */ |
| |
| static volatile int internal_done_flag = 0; |
| static volatile int internal_done_errcode = 0; |
| |
| static void internal_done( Scsi_Cmnd *SCpnt ) |
| { |
| internal_done_errcode = SCpnt->result; |
| ++internal_done_flag; |
| } |
| |
| int fdomain_16x0_command( Scsi_Cmnd *SCpnt ) |
| { |
| fdomain_16x0_queue( SCpnt, internal_done ); |
| |
| while (!internal_done_flag) |
| ; |
| internal_done_flag = 0; |
| return internal_done_errcode; |
| } |
| |
| /* End of code derived from Tommy Thorn's work. */ |
| |
| void print_info( Scsi_Cmnd *SCpnt ) |
| { |
| unsigned int imr; |
| unsigned int irr; |
| unsigned int isr; |
| |
| if (!SCpnt || !SCpnt->host) { |
| printk( "scsi: <fdomain> Cannot provide detailed information\n" ); |
| return; |
| } |
| |
| printk( "%s\n", fdomain_16x0_info( SCpnt->host ) ); |
| print_banner( SCpnt->host ); |
| switch (SCpnt->SCp.phase) { |
| case in_arbitration: printk( "arbitration " ); break; |
| case in_selection: printk( "selection " ); break; |
| case in_other: printk( "other " ); break; |
| default: printk( "unknown " ); break; |
| } |
| |
| printk( "(%d), target = %d cmnd = 0x%02x pieces = %d size = %u\n", |
| SCpnt->SCp.phase, |
| SCpnt->target, |
| *(unsigned char *)SCpnt->cmnd, |
| SCpnt->use_sg, |
| SCpnt->request_bufflen ); |
| printk( "sent_command = %d, have_data_in = %d, timeout = %d\n", |
| SCpnt->SCp.sent_command, |
| SCpnt->SCp.have_data_in, |
| SCpnt->timeout ); |
| #if DEBUG_RACE |
| printk( "in_interrupt_flag = %d\n", in_interrupt_flag ); |
| #endif |
| |
| imr = (inb( 0x0a1 ) << 8) + inb( 0x21 ); |
| outb( 0x0a, 0xa0 ); |
| irr = inb( 0xa0 ) << 8; |
| outb( 0x0a, 0x20 ); |
| irr += inb( 0x20 ); |
| outb( 0x0b, 0xa0 ); |
| isr = inb( 0xa0 ) << 8; |
| outb( 0x0b, 0x20 ); |
| isr += inb( 0x20 ); |
| |
| /* Print out interesting information */ |
| printk( "IMR = 0x%04x", imr ); |
| if (imr & (1 << interrupt_level)) |
| printk( " (masked)" ); |
| printk( ", IRR = 0x%04x, ISR = 0x%04x\n", irr, isr ); |
| |
| printk( "SCSI Status = 0x%02x\n", inb( SCSI_Status_port ) ); |
| printk( "TMC Status = 0x%02x", inb( TMC_Status_port ) ); |
| if (inb( TMC_Status_port & 1)) |
| printk( " (interrupt)" ); |
| printk( "\n" ); |
| printk( "Interrupt Status = 0x%02x", inb( Interrupt_Status_port ) ); |
| if (inb( Interrupt_Status_port ) & 0x08) |
| printk( " (enabled)" ); |
| printk( "\n" ); |
| if (chip == tmc18c50 || chip == tmc18c30) { |
| printk( "FIFO Status = 0x%02x\n", inb( port_base + FIFO_Status ) ); |
| printk( "Int. Condition = 0x%02x\n", |
| inb( port_base + Interrupt_Cond ) ); |
| } |
| printk( "Configuration 1 = 0x%02x\n", inb( port_base + Configuration1 ) ); |
| if (chip == tmc18c50 || chip == tmc18c30) |
| printk( "Configuration 2 = 0x%02x\n", |
| inb( port_base + Configuration2 ) ); |
| } |
| |
| int fdomain_16x0_abort( Scsi_Cmnd *SCpnt) |
| { |
| unsigned long flags; |
| #if EVERY_ACCESS || ERRORS_ONLY || DEBUG_ABORT |
| printk( "scsi: <fdomain> abort " ); |
| #endif |
| |
| save_flags( flags ); |
| cli(); |
| if (!in_command) { |
| #if EVERY_ACCESS || ERRORS_ONLY |
| printk( " (not in command)\n" ); |
| #endif |
| restore_flags( flags ); |
| return SCSI_ABORT_NOT_RUNNING; |
| } else printk( "\n" ); |
| |
| #if DEBUG_ABORT |
| print_info( SCpnt ); |
| #endif |
| |
| fdomain_make_bus_idle(); |
| |
| current_SC->SCp.phase |= aborted; |
| |
| current_SC->result = DID_ABORT << 16; |
| |
| restore_flags( flags ); |
| |
| /* Aborts are not done well. . . */ |
| my_done( DID_ABORT << 16 ); |
| |
| return SCSI_ABORT_SUCCESS; |
| } |
| |
| int fdomain_16x0_reset( Scsi_Cmnd *SCpnt, unsigned int ignored ) |
| { |
| #if DEBUG_RESET |
| static int called_once = 0; |
| #endif |
| |
| #if ERRORS_ONLY |
| if (SCpnt) printk( "scsi: <fdomain> SCSI Bus Reset\n" ); |
| #endif |
| |
| #if DEBUG_RESET |
| if (called_once) print_info( current_SC ); |
| called_once = 1; |
| #endif |
| |
| outb( 1, SCSI_Cntl_port ); |
| do_pause( 2 ); |
| outb( 0, SCSI_Cntl_port ); |
| do_pause( 115 ); |
| outb( 0, SCSI_Mode_Cntl_port ); |
| outb( PARITY_MASK, TMC_Cntl_port ); |
| |
| /* Unless this is the very first call (i.e., SCPnt == NULL), everything |
| is probably hosed at this point. We will, however, try to keep |
| things going by informing the high-level code that we need help. */ |
| |
| return SCSI_RESET_WAKEUP; |
| } |
| |
| #include "sd.h" |
| #include <scsi/scsi_ioctl.h> |
| |
| int fdomain_16x0_biosparam( Scsi_Disk *disk, kdev_t dev, int *info_array ) |
| { |
| int drive; |
| unsigned char buf[512 + sizeof (Scsi_Ioctl_Command)]; |
| Scsi_Ioctl_Command *sic = (Scsi_Ioctl_Command *) buf; |
| int size = disk->capacity; |
| unsigned char *data = sic->data; |
| unsigned char do_read[] = { READ_6, 0, 0, 0, 1, 0 }; |
| int retcode; |
| unsigned long offset; |
| struct drive_info { |
| unsigned short cylinders; |
| unsigned char heads; |
| unsigned char sectors; |
| } i; |
| |
| /* NOTES: |
| The RAM area starts at 0x1f00 from the bios_base address. |
| |
| For BIOS Version 2.0: |
| |
| The drive parameter table seems to start at 0x1f30. |
| The first byte's purpose is not known. |
| Next is the cylinder, head, and sector information. |
| The last 4 bytes appear to be the drive's size in sectors. |
| The other bytes in the drive parameter table are unknown. |
| If anyone figures them out, please send me mail, and I will |
| update these notes. |
| |
| Tape drives do not get placed in this table. |
| |
| There is another table at 0x1fea: |
| If the byte is 0x01, then the SCSI ID is not in use. |
| If the byte is 0x18 or 0x48, then the SCSI ID is in use, |
| although tapes don't seem to be in this table. I haven't |
| seen any other numbers (in a limited sample). |
| |
| 0x1f2d is a drive count (i.e., not including tapes) |
| |
| The table at 0x1fcc are I/O ports addresses for the various |
| operations. I calculate these by hand in this driver code. |
| |
| |
| |
| For the ISA-200S version of BIOS Version 2.0: |
| |
| The drive parameter table starts at 0x1f33. |
| |
| WARNING: Assume that the table entry is 25 bytes long. Someone needs |
| to check this for the Quantum ISA-200S card. |
| |
| |
| |
| For BIOS Version 3.2: |
| |
| The drive parameter table starts at 0x1f70. Each entry is |
| 0x0a bytes long. Heads are one less than we need to report. |
| */ |
| |
| if (major(dev) != SCSI_DISK0_MAJOR) { |
| printk("scsi: <fdomain> fdomain_16x0_biosparam: too many disks"); |
| return 0; |
| } |
| drive = minor(dev) >> 4; |
| |
| if (bios_major == 2) { |
| switch (Quantum) { |
| case 2: /* ISA_200S */ |
| /* The value of 25 has never been verified. |
| It should probably be 15. */ |
| offset = bios_base + 0x1f33 + drive * 25; |
| break; |
| case 3: /* ISA_250MG */ |
| offset = bios_base + 0x1f36 + drive * 15; |
| break; |
| case 4: /* ISA_200S (another one) */ |
| offset = bios_base + 0x1f34 + drive * 15; |
| break; |
| default: |
| offset = bios_base + 0x1f31 + drive * 25; |
| break; |
| } |
| memcpy_fromio( &i, offset, sizeof( struct drive_info ) ); |
| info_array[0] = i.heads; |
| info_array[1] = i.sectors; |
| info_array[2] = i.cylinders; |
| } else if (bios_major == 3 |
| && bios_minor >= 0 |
| && bios_minor < 4) { /* 3.0 and 3.2 BIOS */ |
| memcpy_fromio( &i, bios_base + 0x1f71 + drive * 10, |
| sizeof( struct drive_info ) ); |
| info_array[0] = i.heads + 1; |
| info_array[1] = i.sectors; |
| info_array[2] = i.cylinders; |
| } else { /* 3.4 BIOS (and up?) */ |
| /* This algorithm was provided by Future Domain (much thanks!). */ |
| |
| sic->inlen = 0; /* zero bytes out */ |
| sic->outlen = 512; /* one sector in */ |
| memcpy( data, do_read, sizeof( do_read ) ); |
| retcode = kernel_scsi_ioctl( disk->device, |
| SCSI_IOCTL_SEND_COMMAND, |
| sic ); |
| if (!retcode /* SCSI command ok */ |
| && data[511] == 0xaa && data[510] == 0x55 /* Partition table valid */ |
| && data[0x1c2]) { /* Partition type */ |
| |
| /* The partition table layout is as follows: |
| |
| Start: 0x1b3h |
| Offset: 0 = partition status |
| 1 = starting head |
| 2 = starting sector and cylinder (word, encoded) |
| 4 = partition type |
| 5 = ending head |
| 6 = ending sector and cylinder (word, encoded) |
| 8 = starting absolute sector (double word) |
| c = number of sectors (double word) |
| Signature: 0x1fe = 0x55aa |
| |
| So, this algorithm assumes: |
| 1) the first partition table is in use, |
| 2) the data in the first entry is correct, and |
| 3) partitions never divide cylinders |
| |
| Note that (1) may be FALSE for NetBSD (and other BSD flavors), |
| as well as for Linux. Note also, that Linux doesn't pay any |
| attention to the fields that are used by this algorithm -- it |
| only uses the absolute sector data. Recent versions of Linux's |
| fdisk(1) will fill this data in correctly, and forthcoming |
| versions will check for consistency. |
| |
| Checking for a non-zero partition type is not part of the |
| Future Domain algorithm, but it seemed to be a reasonable thing |
| to do, especially in the Linux and BSD worlds. */ |
| |
| info_array[0] = data[0x1c3] + 1; /* heads */ |
| info_array[1] = data[0x1c4] & 0x3f; /* sectors */ |
| } else { |
| |
| /* Note that this new method guarantees that there will always be |
| less than 1024 cylinders on a platter. This is good for drives |
| up to approximately 7.85GB (where 1GB = 1024 * 1024 kB). */ |
| |
| if ((unsigned int)size >= 0x7e0000U) { |
| info_array[0] = 0xff; /* heads = 255 */ |
| info_array[1] = 0x3f; /* sectors = 63 */ |
| } else if ((unsigned int)size >= 0x200000U) { |
| info_array[0] = 0x80; /* heads = 128 */ |
| info_array[1] = 0x3f; /* sectors = 63 */ |
| } else { |
| info_array[0] = 0x40; /* heads = 64 */ |
| info_array[1] = 0x20; /* sectors = 32 */ |
| } |
| } |
| /* For both methods, compute the cylinders */ |
| info_array[2] = (unsigned int)size / (info_array[0] * info_array[1] ); |
| } |
| |
| return 0; |
| } |
| |
| int fdomain_16x0_release(struct Scsi_Host *shpnt) |
| { |
| if (shpnt->irq) |
| free_irq(shpnt->irq, shpnt); |
| if (shpnt->io_port && shpnt->n_io_port) |
| release_region(shpnt->io_port, shpnt->n_io_port); |
| |
| } |
| |
| MODULE_LICENSE("GPL"); |
| |
| /* Eventually this will go into an include file, but this will be later */ |
| static Scsi_Host_Template driver_template = FDOMAIN_16X0; |
| |
| #include "scsi_module.c" |