| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Synaptics TouchPad PS/2 mouse driver | |
| * | |
| * 2003 Dmitry Torokhov <dtor@mail.ru> | |
| * Added support for pass-through port. Special thanks to Peter Berg Larsen | |
| * for explaining various Synaptics quirks. | |
| * | |
| * 2003 Peter Osterlund <petero2@telia.com> | |
| * Ported to 2.5 input device infrastructure. | |
| * | |
| * Copyright (C) 2001 Stefan Gmeiner <riddlebox@freesurf.ch> | |
| * start merging tpconfig and gpm code to a xfree-input module | |
| * adding some changes and extensions (ex. 3rd and 4th button) | |
| * | |
| * Copyright (c) 1997 C. Scott Ananian <cananian@alumni.priceton.edu> | |
| * Copyright (c) 1998-2000 Bruce Kalk <kall@compass.com> | |
| * code for the special synaptics commands (from the tpconfig-source) | |
| * | |
| * Trademarks are the property of their respective owners. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/delay.h> | |
| #include <linux/dmi.h> | |
| #include <linux/input/mt.h> | |
| #include <linux/serio.h> | |
| #include <linux/libps2.h> | |
| #include <linux/rmi.h> | |
| #include <linux/i2c.h> | |
| #include <linux/slab.h> | |
| #include "psmouse.h" | |
| #include "synaptics.h" | |
| /* | |
| * The x/y limits are taken from the Synaptics TouchPad interfacing Guide, | |
| * section 2.3.2, which says that they should be valid regardless of the | |
| * actual size of the sensor. | |
| * Note that newer firmware allows querying device for maximum useable | |
| * coordinates. | |
| */ | |
| #define XMIN 0 | |
| #define XMAX 6143 | |
| #define YMIN 0 | |
| #define YMAX 6143 | |
| #define XMIN_NOMINAL 1472 | |
| #define XMAX_NOMINAL 5472 | |
| #define YMIN_NOMINAL 1408 | |
| #define YMAX_NOMINAL 4448 | |
| /* Size in bits of absolute position values reported by the hardware */ | |
| #define ABS_POS_BITS 13 | |
| /* | |
| * These values should represent the absolute maximum value that will | |
| * be reported for a positive position value. Some Synaptics firmware | |
| * uses this value to indicate a finger near the edge of the touchpad | |
| * whose precise position cannot be determined. | |
| * | |
| * At least one touchpad is known to report positions in excess of this | |
| * value which are actually negative values truncated to the 13-bit | |
| * reporting range. These values have never been observed to be lower | |
| * than 8184 (i.e. -8), so we treat all values greater than 8176 as | |
| * negative and any other value as positive. | |
| */ | |
| #define X_MAX_POSITIVE 8176 | |
| #define Y_MAX_POSITIVE 8176 | |
| /* maximum ABS_MT_POSITION displacement (in mm) */ | |
| #define DMAX 10 | |
| /***************************************************************************** | |
| * Stuff we need even when we do not want native Synaptics support | |
| ****************************************************************************/ | |
| /* | |
| * Set the synaptics touchpad mode byte by special commands | |
| */ | |
| static int synaptics_mode_cmd(struct psmouse *psmouse, u8 mode) | |
| { | |
| u8 param[1]; | |
| int error; | |
| error = ps2_sliced_command(&psmouse->ps2dev, mode); | |
| if (error) | |
| return error; | |
| param[0] = SYN_PS_SET_MODE2; | |
| error = ps2_command(&psmouse->ps2dev, param, PSMOUSE_CMD_SETRATE); | |
| if (error) | |
| return error; | |
| return 0; | |
| } | |
| int synaptics_detect(struct psmouse *psmouse, bool set_properties) | |
| { | |
| struct ps2dev *ps2dev = &psmouse->ps2dev; | |
| u8 param[4] = { 0 }; | |
| ps2_command(ps2dev, param, PSMOUSE_CMD_SETRES); | |
| ps2_command(ps2dev, param, PSMOUSE_CMD_SETRES); | |
| ps2_command(ps2dev, param, PSMOUSE_CMD_SETRES); | |
| ps2_command(ps2dev, param, PSMOUSE_CMD_SETRES); | |
| ps2_command(ps2dev, param, PSMOUSE_CMD_GETINFO); | |
| if (param[1] != 0x47) | |
| return -ENODEV; | |
| if (set_properties) { | |
| psmouse->vendor = "Synaptics"; | |
| psmouse->name = "TouchPad"; | |
| } | |
| return 0; | |
| } | |
| void synaptics_reset(struct psmouse *psmouse) | |
| { | |
| /* reset touchpad back to relative mode, gestures enabled */ | |
| synaptics_mode_cmd(psmouse, 0); | |
| } | |
| #if defined(CONFIG_MOUSE_PS2_SYNAPTICS) || \ | |
| defined(CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS) | |
| /* This list has been kindly provided by Synaptics. */ | |
| static const char * const topbuttonpad_pnp_ids[] = { | |
| "LEN0017", | |
| "LEN0018", | |
| "LEN0019", | |
| "LEN0023", | |
| "LEN002A", | |
| "LEN002B", | |
| "LEN002C", | |
| "LEN002D", | |
| "LEN002E", | |
| "LEN0033", /* Helix */ | |
| "LEN0034", /* T431s, L440, L540, T540, W540, X1 Carbon 2nd */ | |
| "LEN0035", /* X240 */ | |
| "LEN0036", /* T440 */ | |
| "LEN0037", /* X1 Carbon 2nd */ | |
| "LEN0038", | |
| "LEN0039", /* T440s */ | |
| "LEN0041", | |
| "LEN0042", /* Yoga */ | |
| "LEN0045", | |
| "LEN0047", | |
| "LEN2000", /* S540 */ | |
| "LEN2001", /* Edge E431 */ | |
| "LEN2002", /* Edge E531 */ | |
| "LEN2003", | |
| "LEN2004", /* L440 */ | |
| "LEN2005", | |
| "LEN2006", /* Edge E440/E540 */ | |
| "LEN2007", | |
| "LEN2008", | |
| "LEN2009", | |
| "LEN200A", | |
| "LEN200B", | |
| NULL | |
| }; | |
| static const char * const smbus_pnp_ids[] = { | |
| /* all of the topbuttonpad_pnp_ids are valid, we just add some extras */ | |
| "LEN0048", /* X1 Carbon 3 */ | |
| "LEN0046", /* X250 */ | |
| "LEN0049", /* Yoga 11e */ | |
| "LEN004a", /* W541 */ | |
| "LEN005b", /* P50 */ | |
| "LEN005e", /* T560 */ | |
| "LEN006c", /* T470s */ | |
| "LEN0071", /* T480 */ | |
| "LEN0072", /* X1 Carbon Gen 5 (2017) - Elan/ALPS trackpoint */ | |
| "LEN0073", /* X1 Carbon G5 (Elantech) */ | |
| "LEN0091", /* X1 Carbon 6 */ | |
| "LEN0092", /* X1 Carbon 6 */ | |
| "LEN0093", /* T480 */ | |
| "LEN0096", /* X280 */ | |
| "LEN0097", /* X280 -> ALPS trackpoint */ | |
| "LEN009b", /* T580 */ | |
| "LEN200f", /* T450s */ | |
| "LEN2044", /* L470 */ | |
| "LEN2054", /* E480 */ | |
| "LEN2055", /* E580 */ | |
| "SYN3052", /* HP EliteBook 840 G4 */ | |
| "SYN3221", /* HP 15-ay000 */ | |
| "SYN323d", /* HP Spectre X360 13-w013dx */ | |
| "SYN3257", /* HP Envy 13-ad105ng */ | |
| NULL | |
| }; | |
| static const char * const forcepad_pnp_ids[] = { | |
| "SYN300D", | |
| "SYN3014", | |
| NULL | |
| }; | |
| /* | |
| * Send a command to the synaptics touchpad by special commands | |
| */ | |
| static int synaptics_send_cmd(struct psmouse *psmouse, u8 cmd, u8 *param) | |
| { | |
| int error; | |
| error = ps2_sliced_command(&psmouse->ps2dev, cmd); | |
| if (error) | |
| return error; | |
| error = ps2_command(&psmouse->ps2dev, param, PSMOUSE_CMD_GETINFO); | |
| if (error) | |
| return error; | |
| return 0; | |
| } | |
| static int synaptics_query_int(struct psmouse *psmouse, u8 query_cmd, u32 *val) | |
| { | |
| int error; | |
| union { | |
| __be32 be_val; | |
| char buf[4]; | |
| } resp = { 0 }; | |
| error = synaptics_send_cmd(psmouse, query_cmd, resp.buf + 1); | |
| if (error) | |
| return error; | |
| *val = be32_to_cpu(resp.be_val); | |
| return 0; | |
| } | |
| /* | |
| * Identify Touchpad | |
| * See also the SYN_ID_* macros | |
| */ | |
| static int synaptics_identify(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| int error; | |
| error = synaptics_query_int(psmouse, SYN_QUE_IDENTIFY, &info->identity); | |
| if (error) | |
| return error; | |
| return SYN_ID_IS_SYNAPTICS(info->identity) ? 0 : -ENXIO; | |
| } | |
| /* | |
| * Read the model-id bytes from the touchpad | |
| * see also SYN_MODEL_* macros | |
| */ | |
| static int synaptics_model_id(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| return synaptics_query_int(psmouse, SYN_QUE_MODEL, &info->model_id); | |
| } | |
| /* | |
| * Read the firmware id from the touchpad | |
| */ | |
| static int synaptics_firmware_id(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| return synaptics_query_int(psmouse, SYN_QUE_FIRMWARE_ID, | |
| &info->firmware_id); | |
| } | |
| /* | |
| * Read the board id and the "More Extended Queries" from the touchpad | |
| * The board id is encoded in the "QUERY MODES" response | |
| */ | |
| static int synaptics_query_modes(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| u8 bid[3]; | |
| int error; | |
| /* firmwares prior 7.5 have no board_id encoded */ | |
| if (SYN_ID_FULL(info->identity) < 0x705) | |
| return 0; | |
| error = synaptics_send_cmd(psmouse, SYN_QUE_MODES, bid); | |
| if (error) | |
| return error; | |
| info->board_id = ((bid[0] & 0xfc) << 6) | bid[1]; | |
| if (SYN_MEXT_CAP_BIT(bid[0])) | |
| return synaptics_query_int(psmouse, SYN_QUE_MEXT_CAPAB_10, | |
| &info->ext_cap_10); | |
| return 0; | |
| } | |
| /* | |
| * Read the capability-bits from the touchpad | |
| * see also the SYN_CAP_* macros | |
| */ | |
| static int synaptics_capability(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| int error; | |
| error = synaptics_query_int(psmouse, SYN_QUE_CAPABILITIES, | |
| &info->capabilities); | |
| if (error) | |
| return error; | |
| info->ext_cap = info->ext_cap_0c = 0; | |
| /* | |
| * Older firmwares had submodel ID fixed to 0x47 | |
| */ | |
| if (SYN_ID_FULL(info->identity) < 0x705 && | |
| SYN_CAP_SUBMODEL_ID(info->capabilities) != 0x47) { | |
| return -ENXIO; | |
| } | |
| /* | |
| * Unless capExtended is set the rest of the flags should be ignored | |
| */ | |
| if (!SYN_CAP_EXTENDED(info->capabilities)) | |
| info->capabilities = 0; | |
| if (SYN_EXT_CAP_REQUESTS(info->capabilities) >= 1) { | |
| error = synaptics_query_int(psmouse, SYN_QUE_EXT_CAPAB, | |
| &info->ext_cap); | |
| if (error) { | |
| psmouse_warn(psmouse, | |
| "device claims to have extended capabilities, but I'm not able to read them.\n"); | |
| } else { | |
| /* | |
| * if nExtBtn is greater than 8 it should be considered | |
| * invalid and treated as 0 | |
| */ | |
| if (SYN_CAP_MULTI_BUTTON_NO(info->ext_cap) > 8) | |
| info->ext_cap &= ~SYN_CAP_MB_MASK; | |
| } | |
| } | |
| if (SYN_EXT_CAP_REQUESTS(info->capabilities) >= 4) { | |
| error = synaptics_query_int(psmouse, SYN_QUE_EXT_CAPAB_0C, | |
| &info->ext_cap_0c); | |
| if (error) | |
| psmouse_warn(psmouse, | |
| "device claims to have extended capability 0x0c, but I'm not able to read it.\n"); | |
| } | |
| return 0; | |
| } | |
| /* | |
| * Read touchpad resolution and maximum reported coordinates | |
| * Resolution is left zero if touchpad does not support the query | |
| */ | |
| static int synaptics_resolution(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| u8 resp[3]; | |
| int error; | |
| if (SYN_ID_MAJOR(info->identity) < 4) | |
| return 0; | |
| error = synaptics_send_cmd(psmouse, SYN_QUE_RESOLUTION, resp); | |
| if (!error) { | |
| if (resp[0] != 0 && (resp[1] & 0x80) && resp[2] != 0) { | |
| info->x_res = resp[0]; /* x resolution in units/mm */ | |
| info->y_res = resp[2]; /* y resolution in units/mm */ | |
| } | |
| } | |
| if (SYN_EXT_CAP_REQUESTS(info->capabilities) >= 5 && | |
| SYN_CAP_MAX_DIMENSIONS(info->ext_cap_0c)) { | |
| error = synaptics_send_cmd(psmouse, | |
| SYN_QUE_EXT_MAX_COORDS, resp); | |
| if (error) { | |
| psmouse_warn(psmouse, | |
| "device claims to have max coordinates query, but I'm not able to read it.\n"); | |
| } else { | |
| info->x_max = (resp[0] << 5) | ((resp[1] & 0x0f) << 1); | |
| info->y_max = (resp[2] << 5) | ((resp[1] & 0xf0) >> 3); | |
| psmouse_info(psmouse, | |
| "queried max coordinates: x [..%d], y [..%d]\n", | |
| info->x_max, info->y_max); | |
| } | |
| } | |
| if (SYN_CAP_MIN_DIMENSIONS(info->ext_cap_0c) && | |
| (SYN_EXT_CAP_REQUESTS(info->capabilities) >= 7 || | |
| /* | |
| * Firmware v8.1 does not report proper number of extended | |
| * capabilities, but has been proven to report correct min | |
| * coordinates. | |
| */ | |
| SYN_ID_FULL(info->identity) == 0x801)) { | |
| error = synaptics_send_cmd(psmouse, | |
| SYN_QUE_EXT_MIN_COORDS, resp); | |
| if (error) { | |
| psmouse_warn(psmouse, | |
| "device claims to have min coordinates query, but I'm not able to read it.\n"); | |
| } else { | |
| info->x_min = (resp[0] << 5) | ((resp[1] & 0x0f) << 1); | |
| info->y_min = (resp[2] << 5) | ((resp[1] & 0xf0) >> 3); | |
| psmouse_info(psmouse, | |
| "queried min coordinates: x [%d..], y [%d..]\n", | |
| info->x_min, info->y_min); | |
| } | |
| } | |
| return 0; | |
| } | |
| static int synaptics_query_hardware(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| int error; | |
| memset(info, 0, sizeof(*info)); | |
| error = synaptics_identify(psmouse, info); | |
| if (error) | |
| return error; | |
| error = synaptics_model_id(psmouse, info); | |
| if (error) | |
| return error; | |
| error = synaptics_firmware_id(psmouse, info); | |
| if (error) | |
| return error; | |
| error = synaptics_query_modes(psmouse, info); | |
| if (error) | |
| return error; | |
| error = synaptics_capability(psmouse, info); | |
| if (error) | |
| return error; | |
| error = synaptics_resolution(psmouse, info); | |
| if (error) | |
| return error; | |
| return 0; | |
| } | |
| #endif /* CONFIG_MOUSE_PS2_SYNAPTICS || CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS */ | |
| #ifdef CONFIG_MOUSE_PS2_SYNAPTICS | |
| static bool cr48_profile_sensor; | |
| #define ANY_BOARD_ID 0 | |
| struct min_max_quirk { | |
| const char * const *pnp_ids; | |
| struct { | |
| u32 min, max; | |
| } board_id; | |
| u32 x_min, x_max, y_min, y_max; | |
| }; | |
| static const struct min_max_quirk min_max_pnpid_table[] = { | |
| { | |
| (const char * const []){"LEN0033", NULL}, | |
| {ANY_BOARD_ID, ANY_BOARD_ID}, | |
| 1024, 5052, 2258, 4832 | |
| }, | |
| { | |
| (const char * const []){"LEN0042", NULL}, | |
| {ANY_BOARD_ID, ANY_BOARD_ID}, | |
| 1232, 5710, 1156, 4696 | |
| }, | |
| { | |
| (const char * const []){"LEN0034", "LEN0036", "LEN0037", | |
| "LEN0039", "LEN2002", "LEN2004", | |
| NULL}, | |
| {ANY_BOARD_ID, 2961}, | |
| 1024, 5112, 2024, 4832 | |
| }, | |
| { | |
| (const char * const []){"LEN2000", NULL}, | |
| {ANY_BOARD_ID, ANY_BOARD_ID}, | |
| 1024, 5113, 2021, 4832 | |
| }, | |
| { | |
| (const char * const []){"LEN2001", NULL}, | |
| {ANY_BOARD_ID, ANY_BOARD_ID}, | |
| 1024, 5022, 2508, 4832 | |
| }, | |
| { | |
| (const char * const []){"LEN2006", NULL}, | |
| {2691, 2691}, | |
| 1024, 5045, 2457, 4832 | |
| }, | |
| { | |
| (const char * const []){"LEN2006", NULL}, | |
| {ANY_BOARD_ID, ANY_BOARD_ID}, | |
| 1264, 5675, 1171, 4688 | |
| }, | |
| { } | |
| }; | |
| /***************************************************************************** | |
| * Synaptics communications functions | |
| ****************************************************************************/ | |
| /* | |
| * Synaptics touchpads report the y coordinate from bottom to top, which is | |
| * opposite from what userspace expects. | |
| * This function is used to invert y before reporting. | |
| */ | |
| static int synaptics_invert_y(int y) | |
| { | |
| return YMAX_NOMINAL + YMIN_NOMINAL - y; | |
| } | |
| /* | |
| * Apply quirk(s) if the hardware matches | |
| */ | |
| static void synaptics_apply_quirks(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| int i; | |
| for (i = 0; min_max_pnpid_table[i].pnp_ids; i++) { | |
| if (!psmouse_matches_pnp_id(psmouse, | |
| min_max_pnpid_table[i].pnp_ids)) | |
| continue; | |
| if (min_max_pnpid_table[i].board_id.min != ANY_BOARD_ID && | |
| info->board_id < min_max_pnpid_table[i].board_id.min) | |
| continue; | |
| if (min_max_pnpid_table[i].board_id.max != ANY_BOARD_ID && | |
| info->board_id > min_max_pnpid_table[i].board_id.max) | |
| continue; | |
| info->x_min = min_max_pnpid_table[i].x_min; | |
| info->x_max = min_max_pnpid_table[i].x_max; | |
| info->y_min = min_max_pnpid_table[i].y_min; | |
| info->y_max = min_max_pnpid_table[i].y_max; | |
| psmouse_info(psmouse, | |
| "quirked min/max coordinates: x [%d..%d], y [%d..%d]\n", | |
| info->x_min, info->x_max, | |
| info->y_min, info->y_max); | |
| break; | |
| } | |
| } | |
| static bool synaptics_has_agm(struct synaptics_data *priv) | |
| { | |
| return (SYN_CAP_ADV_GESTURE(priv->info.ext_cap_0c) || | |
| SYN_CAP_IMAGE_SENSOR(priv->info.ext_cap_0c)); | |
| } | |
| static int synaptics_set_advanced_gesture_mode(struct psmouse *psmouse) | |
| { | |
| static u8 param = 0xc8; | |
| int error; | |
| error = ps2_sliced_command(&psmouse->ps2dev, SYN_QUE_MODEL); | |
| if (error) | |
| return error; | |
| error = ps2_command(&psmouse->ps2dev, ¶m, PSMOUSE_CMD_SETRATE); | |
| if (error) | |
| return error; | |
| return 0; | |
| } | |
| static int synaptics_set_mode(struct psmouse *psmouse) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| int error; | |
| priv->mode = 0; | |
| if (priv->absolute_mode) | |
| priv->mode |= SYN_BIT_ABSOLUTE_MODE; | |
| if (priv->disable_gesture) | |
| priv->mode |= SYN_BIT_DISABLE_GESTURE; | |
| if (psmouse->rate >= 80) | |
| priv->mode |= SYN_BIT_HIGH_RATE; | |
| if (SYN_CAP_EXTENDED(priv->info.capabilities)) | |
| priv->mode |= SYN_BIT_W_MODE; | |
| error = synaptics_mode_cmd(psmouse, priv->mode); | |
| if (error) | |
| return error; | |
| if (priv->absolute_mode && synaptics_has_agm(priv)) { | |
| error = synaptics_set_advanced_gesture_mode(psmouse); | |
| if (error) { | |
| psmouse_err(psmouse, | |
| "Advanced gesture mode init failed: %d\n", | |
| error); | |
| return error; | |
| } | |
| } | |
| return 0; | |
| } | |
| static void synaptics_set_rate(struct psmouse *psmouse, unsigned int rate) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| if (rate >= 80) { | |
| priv->mode |= SYN_BIT_HIGH_RATE; | |
| psmouse->rate = 80; | |
| } else { | |
| priv->mode &= ~SYN_BIT_HIGH_RATE; | |
| psmouse->rate = 40; | |
| } | |
| synaptics_mode_cmd(psmouse, priv->mode); | |
| } | |
| /***************************************************************************** | |
| * Synaptics pass-through PS/2 port support | |
| ****************************************************************************/ | |
| static int synaptics_pt_write(struct serio *serio, u8 c) | |
| { | |
| struct psmouse *parent = serio_get_drvdata(serio->parent); | |
| u8 rate_param = SYN_PS_CLIENT_CMD; /* indicates that we want pass-through port */ | |
| int error; | |
| error = ps2_sliced_command(&parent->ps2dev, c); | |
| if (error) | |
| return error; | |
| error = ps2_command(&parent->ps2dev, &rate_param, PSMOUSE_CMD_SETRATE); | |
| if (error) | |
| return error; | |
| return 0; | |
| } | |
| static int synaptics_pt_start(struct serio *serio) | |
| { | |
| struct psmouse *parent = serio_get_drvdata(serio->parent); | |
| struct synaptics_data *priv = parent->private; | |
| serio_pause_rx(parent->ps2dev.serio); | |
| priv->pt_port = serio; | |
| serio_continue_rx(parent->ps2dev.serio); | |
| return 0; | |
| } | |
| static void synaptics_pt_stop(struct serio *serio) | |
| { | |
| struct psmouse *parent = serio_get_drvdata(serio->parent); | |
| struct synaptics_data *priv = parent->private; | |
| serio_pause_rx(parent->ps2dev.serio); | |
| priv->pt_port = NULL; | |
| serio_continue_rx(parent->ps2dev.serio); | |
| } | |
| static int synaptics_is_pt_packet(u8 *buf) | |
| { | |
| return (buf[0] & 0xFC) == 0x84 && (buf[3] & 0xCC) == 0xC4; | |
| } | |
| static void synaptics_pass_pt_packet(struct serio *ptport, u8 *packet) | |
| { | |
| struct psmouse *child = serio_get_drvdata(ptport); | |
| if (child && child->state == PSMOUSE_ACTIVATED) { | |
| serio_interrupt(ptport, packet[1], 0); | |
| serio_interrupt(ptport, packet[4], 0); | |
| serio_interrupt(ptport, packet[5], 0); | |
| if (child->pktsize == 4) | |
| serio_interrupt(ptport, packet[2], 0); | |
| } else { | |
| serio_interrupt(ptport, packet[1], 0); | |
| } | |
| } | |
| static void synaptics_pt_activate(struct psmouse *psmouse) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| struct psmouse *child = serio_get_drvdata(priv->pt_port); | |
| /* adjust the touchpad to child's choice of protocol */ | |
| if (child) { | |
| if (child->pktsize == 4) | |
| priv->mode |= SYN_BIT_FOUR_BYTE_CLIENT; | |
| else | |
| priv->mode &= ~SYN_BIT_FOUR_BYTE_CLIENT; | |
| if (synaptics_mode_cmd(psmouse, priv->mode)) | |
| psmouse_warn(psmouse, | |
| "failed to switch guest protocol\n"); | |
| } | |
| } | |
| static void synaptics_pt_create(struct psmouse *psmouse) | |
| { | |
| struct serio *serio; | |
| serio = kzalloc(sizeof(struct serio), GFP_KERNEL); | |
| if (!serio) { | |
| psmouse_err(psmouse, | |
| "not enough memory for pass-through port\n"); | |
| return; | |
| } | |
| serio->id.type = SERIO_PS_PSTHRU; | |
| strlcpy(serio->name, "Synaptics pass-through", sizeof(serio->name)); | |
| strlcpy(serio->phys, "synaptics-pt/serio0", sizeof(serio->phys)); | |
| serio->write = synaptics_pt_write; | |
| serio->start = synaptics_pt_start; | |
| serio->stop = synaptics_pt_stop; | |
| serio->parent = psmouse->ps2dev.serio; | |
| psmouse->pt_activate = synaptics_pt_activate; | |
| psmouse_info(psmouse, "serio: %s port at %s\n", | |
| serio->name, psmouse->phys); | |
| serio_register_port(serio); | |
| } | |
| /***************************************************************************** | |
| * Functions to interpret the absolute mode packets | |
| ****************************************************************************/ | |
| static void synaptics_parse_agm(const u8 buf[], | |
| struct synaptics_data *priv, | |
| struct synaptics_hw_state *hw) | |
| { | |
| struct synaptics_hw_state *agm = &priv->agm; | |
| int agm_packet_type; | |
| agm_packet_type = (buf[5] & 0x30) >> 4; | |
| switch (agm_packet_type) { | |
| case 1: | |
| /* Gesture packet: (x, y, z) half resolution */ | |
| agm->w = hw->w; | |
| agm->x = (((buf[4] & 0x0f) << 8) | buf[1]) << 1; | |
| agm->y = (((buf[4] & 0xf0) << 4) | buf[2]) << 1; | |
| agm->z = ((buf[3] & 0x30) | (buf[5] & 0x0f)) << 1; | |
| break; | |
| case 2: | |
| /* AGM-CONTACT packet: we are only interested in the count */ | |
| priv->agm_count = buf[1]; | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static void synaptics_parse_ext_buttons(const u8 buf[], | |
| struct synaptics_data *priv, | |
| struct synaptics_hw_state *hw) | |
| { | |
| unsigned int ext_bits = | |
| (SYN_CAP_MULTI_BUTTON_NO(priv->info.ext_cap) + 1) >> 1; | |
| unsigned int ext_mask = GENMASK(ext_bits - 1, 0); | |
| hw->ext_buttons = buf[4] & ext_mask; | |
| hw->ext_buttons |= (buf[5] & ext_mask) << ext_bits; | |
| } | |
| static int synaptics_parse_hw_state(const u8 buf[], | |
| struct synaptics_data *priv, | |
| struct synaptics_hw_state *hw) | |
| { | |
| memset(hw, 0, sizeof(struct synaptics_hw_state)); | |
| if (SYN_MODEL_NEWABS(priv->info.model_id)) { | |
| hw->w = (((buf[0] & 0x30) >> 2) | | |
| ((buf[0] & 0x04) >> 1) | | |
| ((buf[3] & 0x04) >> 2)); | |
| if (synaptics_has_agm(priv) && hw->w == 2) { | |
| synaptics_parse_agm(buf, priv, hw); | |
| return 1; | |
| } | |
| hw->x = (((buf[3] & 0x10) << 8) | | |
| ((buf[1] & 0x0f) << 8) | | |
| buf[4]); | |
| hw->y = (((buf[3] & 0x20) << 7) | | |
| ((buf[1] & 0xf0) << 4) | | |
| buf[5]); | |
| hw->z = buf[2]; | |
| hw->left = (buf[0] & 0x01) ? 1 : 0; | |
| hw->right = (buf[0] & 0x02) ? 1 : 0; | |
| if (priv->is_forcepad) { | |
| /* | |
| * ForcePads, like Clickpads, use middle button | |
| * bits to report primary button clicks. | |
| * Unfortunately they report primary button not | |
| * only when user presses on the pad above certain | |
| * threshold, but also when there are more than one | |
| * finger on the touchpad, which interferes with | |
| * out multi-finger gestures. | |
| */ | |
| if (hw->z == 0) { | |
| /* No contacts */ | |
| priv->press = priv->report_press = false; | |
| } else if (hw->w >= 4 && ((buf[0] ^ buf[3]) & 0x01)) { | |
| /* | |
| * Single-finger touch with pressure above | |
| * the threshold. If pressure stays long | |
| * enough, we'll start reporting primary | |
| * button. We rely on the device continuing | |
| * sending data even if finger does not | |
| * move. | |
| */ | |
| if (!priv->press) { | |
| priv->press_start = jiffies; | |
| priv->press = true; | |
| } else if (time_after(jiffies, | |
| priv->press_start + | |
| msecs_to_jiffies(50))) { | |
| priv->report_press = true; | |
| } | |
| } else { | |
| priv->press = false; | |
| } | |
| hw->left = priv->report_press; | |
| } else if (SYN_CAP_CLICKPAD(priv->info.ext_cap_0c)) { | |
| /* | |
| * Clickpad's button is transmitted as middle button, | |
| * however, since it is primary button, we will report | |
| * it as BTN_LEFT. | |
| */ | |
| hw->left = ((buf[0] ^ buf[3]) & 0x01) ? 1 : 0; | |
| } else if (SYN_CAP_MIDDLE_BUTTON(priv->info.capabilities)) { | |
| hw->middle = ((buf[0] ^ buf[3]) & 0x01) ? 1 : 0; | |
| if (hw->w == 2) | |
| hw->scroll = (s8)buf[1]; | |
| } | |
| if (SYN_CAP_FOUR_BUTTON(priv->info.capabilities)) { | |
| hw->up = ((buf[0] ^ buf[3]) & 0x01) ? 1 : 0; | |
| hw->down = ((buf[0] ^ buf[3]) & 0x02) ? 1 : 0; | |
| } | |
| if (SYN_CAP_MULTI_BUTTON_NO(priv->info.ext_cap) > 0 && | |
| ((buf[0] ^ buf[3]) & 0x02)) { | |
| synaptics_parse_ext_buttons(buf, priv, hw); | |
| } | |
| } else { | |
| hw->x = (((buf[1] & 0x1f) << 8) | buf[2]); | |
| hw->y = (((buf[4] & 0x1f) << 8) | buf[5]); | |
| hw->z = (((buf[0] & 0x30) << 2) | (buf[3] & 0x3F)); | |
| hw->w = (((buf[1] & 0x80) >> 4) | ((buf[0] & 0x04) >> 1)); | |
| hw->left = (buf[0] & 0x01) ? 1 : 0; | |
| hw->right = (buf[0] & 0x02) ? 1 : 0; | |
| } | |
| /* | |
| * Convert wrap-around values to negative. (X|Y)_MAX_POSITIVE | |
| * is used by some firmware to indicate a finger at the edge of | |
| * the touchpad whose precise position cannot be determined, so | |
| * convert these values to the maximum axis value. | |
| */ | |
| if (hw->x > X_MAX_POSITIVE) | |
| hw->x -= 1 << ABS_POS_BITS; | |
| else if (hw->x == X_MAX_POSITIVE) | |
| hw->x = XMAX; | |
| if (hw->y > Y_MAX_POSITIVE) | |
| hw->y -= 1 << ABS_POS_BITS; | |
| else if (hw->y == Y_MAX_POSITIVE) | |
| hw->y = YMAX; | |
| return 0; | |
| } | |
| static void synaptics_report_semi_mt_slot(struct input_dev *dev, int slot, | |
| bool active, int x, int y) | |
| { | |
| input_mt_slot(dev, slot); | |
| input_mt_report_slot_state(dev, MT_TOOL_FINGER, active); | |
| if (active) { | |
| input_report_abs(dev, ABS_MT_POSITION_X, x); | |
| input_report_abs(dev, ABS_MT_POSITION_Y, synaptics_invert_y(y)); | |
| } | |
| } | |
| static void synaptics_report_semi_mt_data(struct input_dev *dev, | |
| const struct synaptics_hw_state *a, | |
| const struct synaptics_hw_state *b, | |
| int num_fingers) | |
| { | |
| if (num_fingers >= 2) { | |
| synaptics_report_semi_mt_slot(dev, 0, true, min(a->x, b->x), | |
| min(a->y, b->y)); | |
| synaptics_report_semi_mt_slot(dev, 1, true, max(a->x, b->x), | |
| max(a->y, b->y)); | |
| } else if (num_fingers == 1) { | |
| synaptics_report_semi_mt_slot(dev, 0, true, a->x, a->y); | |
| synaptics_report_semi_mt_slot(dev, 1, false, 0, 0); | |
| } else { | |
| synaptics_report_semi_mt_slot(dev, 0, false, 0, 0); | |
| synaptics_report_semi_mt_slot(dev, 1, false, 0, 0); | |
| } | |
| } | |
| static void synaptics_report_ext_buttons(struct psmouse *psmouse, | |
| const struct synaptics_hw_state *hw) | |
| { | |
| struct input_dev *dev = psmouse->dev; | |
| struct synaptics_data *priv = psmouse->private; | |
| int ext_bits = (SYN_CAP_MULTI_BUTTON_NO(priv->info.ext_cap) + 1) >> 1; | |
| int i; | |
| if (!SYN_CAP_MULTI_BUTTON_NO(priv->info.ext_cap)) | |
| return; | |
| /* Bug in FW 8.1 & 8.2, buttons are reported only when ExtBit is 1 */ | |
| if ((SYN_ID_FULL(priv->info.identity) == 0x801 || | |
| SYN_ID_FULL(priv->info.identity) == 0x802) && | |
| !((psmouse->packet[0] ^ psmouse->packet[3]) & 0x02)) | |
| return; | |
| if (!SYN_CAP_EXT_BUTTONS_STICK(priv->info.ext_cap_10)) { | |
| for (i = 0; i < ext_bits; i++) { | |
| input_report_key(dev, BTN_0 + 2 * i, | |
| hw->ext_buttons & BIT(i)); | |
| input_report_key(dev, BTN_1 + 2 * i, | |
| hw->ext_buttons & BIT(i + ext_bits)); | |
| } | |
| return; | |
| } | |
| /* | |
| * This generation of touchpads has the trackstick buttons | |
| * physically wired to the touchpad. Re-route them through | |
| * the pass-through interface. | |
| */ | |
| if (priv->pt_port) { | |
| u8 pt_buttons; | |
| /* The trackstick expects at most 3 buttons */ | |
| pt_buttons = SYN_EXT_BUTTON_STICK_L(hw->ext_buttons) | | |
| SYN_EXT_BUTTON_STICK_R(hw->ext_buttons) << 1 | | |
| SYN_EXT_BUTTON_STICK_M(hw->ext_buttons) << 2; | |
| serio_interrupt(priv->pt_port, | |
| PSMOUSE_OOB_EXTRA_BTNS, SERIO_OOB_DATA); | |
| serio_interrupt(priv->pt_port, pt_buttons, SERIO_OOB_DATA); | |
| } | |
| } | |
| static void synaptics_report_buttons(struct psmouse *psmouse, | |
| const struct synaptics_hw_state *hw) | |
| { | |
| struct input_dev *dev = psmouse->dev; | |
| struct synaptics_data *priv = psmouse->private; | |
| input_report_key(dev, BTN_LEFT, hw->left); | |
| input_report_key(dev, BTN_RIGHT, hw->right); | |
| if (SYN_CAP_MIDDLE_BUTTON(priv->info.capabilities)) | |
| input_report_key(dev, BTN_MIDDLE, hw->middle); | |
| if (SYN_CAP_FOUR_BUTTON(priv->info.capabilities)) { | |
| input_report_key(dev, BTN_FORWARD, hw->up); | |
| input_report_key(dev, BTN_BACK, hw->down); | |
| } | |
| synaptics_report_ext_buttons(psmouse, hw); | |
| } | |
| static void synaptics_report_mt_data(struct psmouse *psmouse, | |
| const struct synaptics_hw_state *sgm, | |
| int num_fingers) | |
| { | |
| struct input_dev *dev = psmouse->dev; | |
| struct synaptics_data *priv = psmouse->private; | |
| const struct synaptics_hw_state *hw[2] = { sgm, &priv->agm }; | |
| struct input_mt_pos pos[2]; | |
| int slot[2], nsemi, i; | |
| nsemi = clamp_val(num_fingers, 0, 2); | |
| for (i = 0; i < nsemi; i++) { | |
| pos[i].x = hw[i]->x; | |
| pos[i].y = synaptics_invert_y(hw[i]->y); | |
| } | |
| input_mt_assign_slots(dev, slot, pos, nsemi, DMAX * priv->info.x_res); | |
| for (i = 0; i < nsemi; i++) { | |
| input_mt_slot(dev, slot[i]); | |
| input_mt_report_slot_state(dev, MT_TOOL_FINGER, true); | |
| input_report_abs(dev, ABS_MT_POSITION_X, pos[i].x); | |
| input_report_abs(dev, ABS_MT_POSITION_Y, pos[i].y); | |
| input_report_abs(dev, ABS_MT_PRESSURE, hw[i]->z); | |
| } | |
| input_mt_drop_unused(dev); | |
| /* Don't use active slot count to generate BTN_TOOL events. */ | |
| input_mt_report_pointer_emulation(dev, false); | |
| /* Send the number of fingers reported by touchpad itself. */ | |
| input_mt_report_finger_count(dev, num_fingers); | |
| synaptics_report_buttons(psmouse, sgm); | |
| input_sync(dev); | |
| } | |
| static void synaptics_image_sensor_process(struct psmouse *psmouse, | |
| struct synaptics_hw_state *sgm) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| int num_fingers; | |
| /* | |
| * Update mt_state using the new finger count and current mt_state. | |
| */ | |
| if (sgm->z == 0) | |
| num_fingers = 0; | |
| else if (sgm->w >= 4) | |
| num_fingers = 1; | |
| else if (sgm->w == 0) | |
| num_fingers = 2; | |
| else if (sgm->w == 1) | |
| num_fingers = priv->agm_count ? priv->agm_count : 3; | |
| else | |
| num_fingers = 4; | |
| /* Send resulting input events to user space */ | |
| synaptics_report_mt_data(psmouse, sgm, num_fingers); | |
| } | |
| static bool synaptics_has_multifinger(struct synaptics_data *priv) | |
| { | |
| if (SYN_CAP_MULTIFINGER(priv->info.capabilities)) | |
| return true; | |
| /* Advanced gesture mode also sends multi finger data */ | |
| return synaptics_has_agm(priv); | |
| } | |
| /* | |
| * called for each full received packet from the touchpad | |
| */ | |
| static void synaptics_process_packet(struct psmouse *psmouse) | |
| { | |
| struct input_dev *dev = psmouse->dev; | |
| struct synaptics_data *priv = psmouse->private; | |
| struct synaptics_device_info *info = &priv->info; | |
| struct synaptics_hw_state hw; | |
| int num_fingers; | |
| int finger_width; | |
| if (synaptics_parse_hw_state(psmouse->packet, priv, &hw)) | |
| return; | |
| if (SYN_CAP_IMAGE_SENSOR(info->ext_cap_0c)) { | |
| synaptics_image_sensor_process(psmouse, &hw); | |
| return; | |
| } | |
| if (hw.scroll) { | |
| priv->scroll += hw.scroll; | |
| while (priv->scroll >= 4) { | |
| input_report_key(dev, BTN_BACK, !hw.down); | |
| input_sync(dev); | |
| input_report_key(dev, BTN_BACK, hw.down); | |
| input_sync(dev); | |
| priv->scroll -= 4; | |
| } | |
| while (priv->scroll <= -4) { | |
| input_report_key(dev, BTN_FORWARD, !hw.up); | |
| input_sync(dev); | |
| input_report_key(dev, BTN_FORWARD, hw.up); | |
| input_sync(dev); | |
| priv->scroll += 4; | |
| } | |
| return; | |
| } | |
| if (hw.z > 0 && hw.x > 1) { | |
| num_fingers = 1; | |
| finger_width = 5; | |
| if (SYN_CAP_EXTENDED(info->capabilities)) { | |
| switch (hw.w) { | |
| case 0 ... 1: | |
| if (synaptics_has_multifinger(priv)) | |
| num_fingers = hw.w + 2; | |
| break; | |
| case 2: | |
| if (SYN_MODEL_PEN(info->model_id)) | |
| ; /* Nothing, treat a pen as a single finger */ | |
| break; | |
| case 4 ... 15: | |
| if (SYN_CAP_PALMDETECT(info->capabilities)) | |
| finger_width = hw.w; | |
| break; | |
| } | |
| } | |
| } else { | |
| num_fingers = 0; | |
| finger_width = 0; | |
| } | |
| if (cr48_profile_sensor) { | |
| synaptics_report_mt_data(psmouse, &hw, num_fingers); | |
| return; | |
| } | |
| if (SYN_CAP_ADV_GESTURE(info->ext_cap_0c)) | |
| synaptics_report_semi_mt_data(dev, &hw, &priv->agm, | |
| num_fingers); | |
| /* Post events | |
| * BTN_TOUCH has to be first as mousedev relies on it when doing | |
| * absolute -> relative conversion | |
| */ | |
| if (hw.z > 30) input_report_key(dev, BTN_TOUCH, 1); | |
| if (hw.z < 25) input_report_key(dev, BTN_TOUCH, 0); | |
| if (num_fingers > 0) { | |
| input_report_abs(dev, ABS_X, hw.x); | |
| input_report_abs(dev, ABS_Y, synaptics_invert_y(hw.y)); | |
| } | |
| input_report_abs(dev, ABS_PRESSURE, hw.z); | |
| if (SYN_CAP_PALMDETECT(info->capabilities)) | |
| input_report_abs(dev, ABS_TOOL_WIDTH, finger_width); | |
| input_report_key(dev, BTN_TOOL_FINGER, num_fingers == 1); | |
| if (synaptics_has_multifinger(priv)) { | |
| input_report_key(dev, BTN_TOOL_DOUBLETAP, num_fingers == 2); | |
| input_report_key(dev, BTN_TOOL_TRIPLETAP, num_fingers == 3); | |
| } | |
| synaptics_report_buttons(psmouse, &hw); | |
| input_sync(dev); | |
| } | |
| static bool synaptics_validate_byte(struct psmouse *psmouse, | |
| int idx, enum synaptics_pkt_type pkt_type) | |
| { | |
| static const u8 newabs_mask[] = { 0xC8, 0x00, 0x00, 0xC8, 0x00 }; | |
| static const u8 newabs_rel_mask[] = { 0xC0, 0x00, 0x00, 0xC0, 0x00 }; | |
| static const u8 newabs_rslt[] = { 0x80, 0x00, 0x00, 0xC0, 0x00 }; | |
| static const u8 oldabs_mask[] = { 0xC0, 0x60, 0x00, 0xC0, 0x60 }; | |
| static const u8 oldabs_rslt[] = { 0xC0, 0x00, 0x00, 0x80, 0x00 }; | |
| const u8 *packet = psmouse->packet; | |
| if (idx < 0 || idx > 4) | |
| return false; | |
| switch (pkt_type) { | |
| case SYN_NEWABS: | |
| case SYN_NEWABS_RELAXED: | |
| return (packet[idx] & newabs_rel_mask[idx]) == newabs_rslt[idx]; | |
| case SYN_NEWABS_STRICT: | |
| return (packet[idx] & newabs_mask[idx]) == newabs_rslt[idx]; | |
| case SYN_OLDABS: | |
| return (packet[idx] & oldabs_mask[idx]) == oldabs_rslt[idx]; | |
| default: | |
| psmouse_err(psmouse, "unknown packet type %d\n", pkt_type); | |
| return false; | |
| } | |
| } | |
| static enum synaptics_pkt_type | |
| synaptics_detect_pkt_type(struct psmouse *psmouse) | |
| { | |
| int i; | |
| for (i = 0; i < 5; i++) { | |
| if (!synaptics_validate_byte(psmouse, i, SYN_NEWABS_STRICT)) { | |
| psmouse_info(psmouse, "using relaxed packet validation\n"); | |
| return SYN_NEWABS_RELAXED; | |
| } | |
| } | |
| return SYN_NEWABS_STRICT; | |
| } | |
| static psmouse_ret_t synaptics_process_byte(struct psmouse *psmouse) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| if (psmouse->pktcnt >= 6) { /* Full packet received */ | |
| if (unlikely(priv->pkt_type == SYN_NEWABS)) | |
| priv->pkt_type = synaptics_detect_pkt_type(psmouse); | |
| if (SYN_CAP_PASS_THROUGH(priv->info.capabilities) && | |
| synaptics_is_pt_packet(psmouse->packet)) { | |
| if (priv->pt_port) | |
| synaptics_pass_pt_packet(priv->pt_port, | |
| psmouse->packet); | |
| } else | |
| synaptics_process_packet(psmouse); | |
| return PSMOUSE_FULL_PACKET; | |
| } | |
| return synaptics_validate_byte(psmouse, psmouse->pktcnt - 1, priv->pkt_type) ? | |
| PSMOUSE_GOOD_DATA : PSMOUSE_BAD_DATA; | |
| } | |
| /***************************************************************************** | |
| * Driver initialization/cleanup functions | |
| ****************************************************************************/ | |
| static void set_abs_position_params(struct input_dev *dev, | |
| struct synaptics_device_info *info, | |
| int x_code, int y_code) | |
| { | |
| int x_min = info->x_min ?: XMIN_NOMINAL; | |
| int x_max = info->x_max ?: XMAX_NOMINAL; | |
| int y_min = info->y_min ?: YMIN_NOMINAL; | |
| int y_max = info->y_max ?: YMAX_NOMINAL; | |
| int fuzz = SYN_CAP_REDUCED_FILTERING(info->ext_cap_0c) ? | |
| SYN_REDUCED_FILTER_FUZZ : 0; | |
| input_set_abs_params(dev, x_code, x_min, x_max, fuzz, 0); | |
| input_set_abs_params(dev, y_code, y_min, y_max, fuzz, 0); | |
| input_abs_set_res(dev, x_code, info->x_res); | |
| input_abs_set_res(dev, y_code, info->y_res); | |
| } | |
| static int set_input_params(struct psmouse *psmouse, | |
| struct synaptics_data *priv) | |
| { | |
| struct input_dev *dev = psmouse->dev; | |
| struct synaptics_device_info *info = &priv->info; | |
| int i; | |
| int error; | |
| /* Reset default psmouse capabilities */ | |
| __clear_bit(EV_REL, dev->evbit); | |
| bitmap_zero(dev->relbit, REL_CNT); | |
| bitmap_zero(dev->keybit, KEY_CNT); | |
| /* Things that apply to both modes */ | |
| __set_bit(INPUT_PROP_POINTER, dev->propbit); | |
| input_set_capability(dev, EV_KEY, BTN_LEFT); | |
| /* Clickpads report only left button */ | |
| if (!SYN_CAP_CLICKPAD(info->ext_cap_0c)) { | |
| input_set_capability(dev, EV_KEY, BTN_RIGHT); | |
| if (SYN_CAP_MIDDLE_BUTTON(info->capabilities)) | |
| input_set_capability(dev, EV_KEY, BTN_MIDDLE); | |
| } | |
| if (!priv->absolute_mode) { | |
| /* Relative mode */ | |
| input_set_capability(dev, EV_REL, REL_X); | |
| input_set_capability(dev, EV_REL, REL_Y); | |
| return 0; | |
| } | |
| /* Absolute mode */ | |
| set_abs_position_params(dev, &priv->info, ABS_X, ABS_Y); | |
| input_set_abs_params(dev, ABS_PRESSURE, 0, 255, 0, 0); | |
| if (cr48_profile_sensor) | |
| input_set_abs_params(dev, ABS_MT_PRESSURE, 0, 255, 0, 0); | |
| if (SYN_CAP_IMAGE_SENSOR(info->ext_cap_0c)) { | |
| set_abs_position_params(dev, info, | |
| ABS_MT_POSITION_X, ABS_MT_POSITION_Y); | |
| /* Image sensors can report per-contact pressure */ | |
| input_set_abs_params(dev, ABS_MT_PRESSURE, 0, 255, 0, 0); | |
| error = input_mt_init_slots(dev, 2, | |
| INPUT_MT_POINTER | INPUT_MT_TRACK); | |
| if (error) | |
| return error; | |
| /* Image sensors can signal 4 and 5 finger clicks */ | |
| input_set_capability(dev, EV_KEY, BTN_TOOL_QUADTAP); | |
| input_set_capability(dev, EV_KEY, BTN_TOOL_QUINTTAP); | |
| } else if (SYN_CAP_ADV_GESTURE(info->ext_cap_0c)) { | |
| set_abs_position_params(dev, info, | |
| ABS_MT_POSITION_X, ABS_MT_POSITION_Y); | |
| /* | |
| * Profile sensor in CR-48 tracks contacts reasonably well, | |
| * other non-image sensors with AGM use semi-mt. | |
| */ | |
| error = input_mt_init_slots(dev, 2, | |
| INPUT_MT_POINTER | | |
| (cr48_profile_sensor ? | |
| INPUT_MT_TRACK : | |
| INPUT_MT_SEMI_MT)); | |
| if (error) | |
| return error; | |
| /* | |
| * For semi-mt devices we send ABS_X/Y ourselves instead of | |
| * input_mt_report_pointer_emulation. But | |
| * input_mt_init_slots() resets the fuzz to 0, leading to a | |
| * filtered ABS_MT_POSITION_X but an unfiltered ABS_X | |
| * position. Let's re-initialize ABS_X/Y here. | |
| */ | |
| if (!cr48_profile_sensor) | |
| set_abs_position_params(dev, &priv->info, ABS_X, ABS_Y); | |
| } | |
| if (SYN_CAP_PALMDETECT(info->capabilities)) | |
| input_set_abs_params(dev, ABS_TOOL_WIDTH, 0, 15, 0, 0); | |
| input_set_capability(dev, EV_KEY, BTN_TOUCH); | |
| input_set_capability(dev, EV_KEY, BTN_TOOL_FINGER); | |
| if (synaptics_has_multifinger(priv)) { | |
| input_set_capability(dev, EV_KEY, BTN_TOOL_DOUBLETAP); | |
| input_set_capability(dev, EV_KEY, BTN_TOOL_TRIPLETAP); | |
| } | |
| if (SYN_CAP_FOUR_BUTTON(info->capabilities) || | |
| SYN_CAP_MIDDLE_BUTTON(info->capabilities)) { | |
| input_set_capability(dev, EV_KEY, BTN_FORWARD); | |
| input_set_capability(dev, EV_KEY, BTN_BACK); | |
| } | |
| if (!SYN_CAP_EXT_BUTTONS_STICK(info->ext_cap_10)) | |
| for (i = 0; i < SYN_CAP_MULTI_BUTTON_NO(info->ext_cap); i++) | |
| input_set_capability(dev, EV_KEY, BTN_0 + i); | |
| if (SYN_CAP_CLICKPAD(info->ext_cap_0c)) { | |
| __set_bit(INPUT_PROP_BUTTONPAD, dev->propbit); | |
| if (psmouse_matches_pnp_id(psmouse, topbuttonpad_pnp_ids) && | |
| !SYN_CAP_EXT_BUTTONS_STICK(info->ext_cap_10)) | |
| __set_bit(INPUT_PROP_TOPBUTTONPAD, dev->propbit); | |
| } | |
| return 0; | |
| } | |
| static ssize_t synaptics_show_disable_gesture(struct psmouse *psmouse, | |
| void *data, char *buf) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| return sprintf(buf, "%c\n", priv->disable_gesture ? '1' : '0'); | |
| } | |
| static ssize_t synaptics_set_disable_gesture(struct psmouse *psmouse, | |
| void *data, const char *buf, | |
| size_t len) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| unsigned int value; | |
| int err; | |
| err = kstrtouint(buf, 10, &value); | |
| if (err) | |
| return err; | |
| if (value > 1) | |
| return -EINVAL; | |
| if (value == priv->disable_gesture) | |
| return len; | |
| priv->disable_gesture = value; | |
| if (value) | |
| priv->mode |= SYN_BIT_DISABLE_GESTURE; | |
| else | |
| priv->mode &= ~SYN_BIT_DISABLE_GESTURE; | |
| if (synaptics_mode_cmd(psmouse, priv->mode)) | |
| return -EIO; | |
| return len; | |
| } | |
| PSMOUSE_DEFINE_ATTR(disable_gesture, S_IWUSR | S_IRUGO, NULL, | |
| synaptics_show_disable_gesture, | |
| synaptics_set_disable_gesture); | |
| static void synaptics_disconnect(struct psmouse *psmouse) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| /* | |
| * We might have left a breadcrumb when trying to | |
| * set up SMbus companion. | |
| */ | |
| psmouse_smbus_cleanup(psmouse); | |
| if (!priv->absolute_mode && | |
| SYN_ID_DISGEST_SUPPORTED(priv->info.identity)) | |
| device_remove_file(&psmouse->ps2dev.serio->dev, | |
| &psmouse_attr_disable_gesture.dattr); | |
| synaptics_reset(psmouse); | |
| kfree(priv); | |
| psmouse->private = NULL; | |
| } | |
| static int synaptics_reconnect(struct psmouse *psmouse) | |
| { | |
| struct synaptics_data *priv = psmouse->private; | |
| struct synaptics_device_info info; | |
| u8 param[2]; | |
| int retry = 0; | |
| int error; | |
| do { | |
| psmouse_reset(psmouse); | |
| if (retry) { | |
| /* | |
| * On some boxes, right after resuming, the touchpad | |
| * needs some time to finish initializing (I assume | |
| * it needs time to calibrate) and start responding | |
| * to Synaptics-specific queries, so let's wait a | |
| * bit. | |
| */ | |
| ssleep(1); | |
| } | |
| ps2_command(&psmouse->ps2dev, param, PSMOUSE_CMD_GETID); | |
| error = synaptics_detect(psmouse, 0); | |
| } while (error && ++retry < 3); | |
| if (error) | |
| return error; | |
| if (retry > 1) | |
| psmouse_dbg(psmouse, "reconnected after %d tries\n", retry); | |
| error = synaptics_query_hardware(psmouse, &info); | |
| if (error) { | |
| psmouse_err(psmouse, "Unable to query device.\n"); | |
| return error; | |
| } | |
| error = synaptics_set_mode(psmouse); | |
| if (error) { | |
| psmouse_err(psmouse, "Unable to initialize device.\n"); | |
| return error; | |
| } | |
| if (info.identity != priv->info.identity || | |
| info.model_id != priv->info.model_id || | |
| info.capabilities != priv->info.capabilities || | |
| info.ext_cap != priv->info.ext_cap) { | |
| psmouse_err(psmouse, | |
| "hardware appears to be different: id(%u-%u), model(%u-%u), caps(%x-%x), ext(%x-%x).\n", | |
| priv->info.identity, info.identity, | |
| priv->info.model_id, info.model_id, | |
| priv->info.capabilities, info.capabilities, | |
| priv->info.ext_cap, info.ext_cap); | |
| return -ENXIO; | |
| } | |
| return 0; | |
| } | |
| static bool impaired_toshiba_kbc; | |
| static const struct dmi_system_id toshiba_dmi_table[] __initconst = { | |
| #if defined(CONFIG_DMI) && defined(CONFIG_X86) | |
| { | |
| /* Toshiba Satellite */ | |
| .matches = { | |
| DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), | |
| DMI_MATCH(DMI_PRODUCT_NAME, "Satellite"), | |
| }, | |
| }, | |
| { | |
| /* Toshiba Dynabook */ | |
| .matches = { | |
| DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), | |
| DMI_MATCH(DMI_PRODUCT_NAME, "dynabook"), | |
| }, | |
| }, | |
| { | |
| /* Toshiba Portege M300 */ | |
| .matches = { | |
| DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), | |
| DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M300"), | |
| }, | |
| }, | |
| { | |
| /* Toshiba Portege M300 */ | |
| .matches = { | |
| DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), | |
| DMI_MATCH(DMI_PRODUCT_NAME, "Portable PC"), | |
| DMI_MATCH(DMI_PRODUCT_VERSION, "Version 1.0"), | |
| }, | |
| }, | |
| #endif | |
| { } | |
| }; | |
| static bool broken_olpc_ec; | |
| static const struct dmi_system_id olpc_dmi_table[] __initconst = { | |
| #if defined(CONFIG_DMI) && defined(CONFIG_OLPC) | |
| { | |
| /* OLPC XO-1 or XO-1.5 */ | |
| .matches = { | |
| DMI_MATCH(DMI_SYS_VENDOR, "OLPC"), | |
| DMI_MATCH(DMI_PRODUCT_NAME, "XO"), | |
| }, | |
| }, | |
| #endif | |
| { } | |
| }; | |
| static const struct dmi_system_id __initconst cr48_dmi_table[] = { | |
| #if defined(CONFIG_DMI) && defined(CONFIG_X86) | |
| { | |
| /* Cr-48 Chromebook (Codename Mario) */ | |
| .matches = { | |
| DMI_MATCH(DMI_SYS_VENDOR, "IEC"), | |
| DMI_MATCH(DMI_PRODUCT_NAME, "Mario"), | |
| }, | |
| }, | |
| #endif | |
| { } | |
| }; | |
| void __init synaptics_module_init(void) | |
| { | |
| impaired_toshiba_kbc = dmi_check_system(toshiba_dmi_table); | |
| broken_olpc_ec = dmi_check_system(olpc_dmi_table); | |
| cr48_profile_sensor = dmi_check_system(cr48_dmi_table); | |
| } | |
| static int synaptics_init_ps2(struct psmouse *psmouse, | |
| struct synaptics_device_info *info, | |
| bool absolute_mode) | |
| { | |
| struct synaptics_data *priv; | |
| int err; | |
| synaptics_apply_quirks(psmouse, info); | |
| psmouse->private = priv = kzalloc(sizeof(struct synaptics_data), GFP_KERNEL); | |
| if (!priv) | |
| return -ENOMEM; | |
| priv->info = *info; | |
| priv->absolute_mode = absolute_mode; | |
| if (SYN_ID_DISGEST_SUPPORTED(info->identity)) | |
| priv->disable_gesture = true; | |
| /* | |
| * Unfortunately ForcePad capability is not exported over PS/2, | |
| * so we have to resort to checking PNP IDs. | |
| */ | |
| priv->is_forcepad = psmouse_matches_pnp_id(psmouse, forcepad_pnp_ids); | |
| err = synaptics_set_mode(psmouse); | |
| if (err) { | |
| psmouse_err(psmouse, "Unable to initialize device.\n"); | |
| goto init_fail; | |
| } | |
| priv->pkt_type = SYN_MODEL_NEWABS(info->model_id) ? | |
| SYN_NEWABS : SYN_OLDABS; | |
| psmouse_info(psmouse, | |
| "Touchpad model: %lu, fw: %lu.%lu, id: %#x, caps: %#x/%#x/%#x/%#x, board id: %u, fw id: %u\n", | |
| SYN_ID_MODEL(info->identity), | |
| SYN_ID_MAJOR(info->identity), SYN_ID_MINOR(info->identity), | |
| info->model_id, | |
| info->capabilities, info->ext_cap, info->ext_cap_0c, | |
| info->ext_cap_10, info->board_id, info->firmware_id); | |
| err = set_input_params(psmouse, priv); | |
| if (err) { | |
| psmouse_err(psmouse, | |
| "failed to set up capabilities: %d\n", err); | |
| goto init_fail; | |
| } | |
| /* | |
| * Encode touchpad model so that it can be used to set | |
| * input device->id.version and be visible to userspace. | |
| * Because version is __u16 we have to drop something. | |
| * Hardware info bits seem to be good candidates as they | |
| * are documented to be for Synaptics corp. internal use. | |
| */ | |
| psmouse->model = ((info->model_id & 0x00ff0000) >> 8) | | |
| (info->model_id & 0x000000ff); | |
| if (absolute_mode) { | |
| psmouse->protocol_handler = synaptics_process_byte; | |
| psmouse->pktsize = 6; | |
| } else { | |
| /* Relative mode follows standard PS/2 mouse protocol */ | |
| psmouse->protocol_handler = psmouse_process_byte; | |
| psmouse->pktsize = 3; | |
| } | |
| psmouse->set_rate = synaptics_set_rate; | |
| psmouse->disconnect = synaptics_disconnect; | |
| psmouse->reconnect = synaptics_reconnect; | |
| psmouse->cleanup = synaptics_reset; | |
| /* Synaptics can usually stay in sync without extra help */ | |
| psmouse->resync_time = 0; | |
| if (SYN_CAP_PASS_THROUGH(info->capabilities)) | |
| synaptics_pt_create(psmouse); | |
| /* | |
| * Toshiba's KBC seems to have trouble handling data from | |
| * Synaptics at full rate. Switch to a lower rate (roughly | |
| * the same rate as a standard PS/2 mouse). | |
| */ | |
| if (psmouse->rate >= 80 && impaired_toshiba_kbc) { | |
| psmouse_info(psmouse, | |
| "Toshiba %s detected, limiting rate to 40pps.\n", | |
| dmi_get_system_info(DMI_PRODUCT_NAME)); | |
| psmouse->rate = 40; | |
| } | |
| if (!priv->absolute_mode && SYN_ID_DISGEST_SUPPORTED(info->identity)) { | |
| err = device_create_file(&psmouse->ps2dev.serio->dev, | |
| &psmouse_attr_disable_gesture.dattr); | |
| if (err) { | |
| psmouse_err(psmouse, | |
| "Failed to create disable_gesture attribute (%d)", | |
| err); | |
| goto init_fail; | |
| } | |
| } | |
| return 0; | |
| init_fail: | |
| kfree(priv); | |
| return err; | |
| } | |
| static int __synaptics_init(struct psmouse *psmouse, bool absolute_mode) | |
| { | |
| struct synaptics_device_info info; | |
| int error; | |
| psmouse_reset(psmouse); | |
| error = synaptics_query_hardware(psmouse, &info); | |
| if (error) { | |
| psmouse_err(psmouse, "Unable to query device: %d\n", error); | |
| return error; | |
| } | |
| return synaptics_init_ps2(psmouse, &info, absolute_mode); | |
| } | |
| int synaptics_init_absolute(struct psmouse *psmouse) | |
| { | |
| return __synaptics_init(psmouse, true); | |
| } | |
| int synaptics_init_relative(struct psmouse *psmouse) | |
| { | |
| return __synaptics_init(psmouse, false); | |
| } | |
| static int synaptics_setup_ps2(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| bool absolute_mode = true; | |
| int error; | |
| /* | |
| * The OLPC XO has issues with Synaptics' absolute mode; the constant | |
| * packet spew overloads the EC such that key presses on the keyboard | |
| * are missed. Given that, don't even attempt to use Absolute mode. | |
| * Relative mode seems to work just fine. | |
| */ | |
| if (broken_olpc_ec) { | |
| psmouse_info(psmouse, | |
| "OLPC XO detected, forcing relative protocol.\n"); | |
| absolute_mode = false; | |
| } | |
| error = synaptics_init_ps2(psmouse, info, absolute_mode); | |
| if (error) | |
| return error; | |
| return absolute_mode ? PSMOUSE_SYNAPTICS : PSMOUSE_SYNAPTICS_RELATIVE; | |
| } | |
| #else /* CONFIG_MOUSE_PS2_SYNAPTICS */ | |
| void __init synaptics_module_init(void) | |
| { | |
| } | |
| static int __maybe_unused | |
| synaptics_setup_ps2(struct psmouse *psmouse, | |
| struct synaptics_device_info *info) | |
| { | |
| return -ENOSYS; | |
| } | |
| #endif /* CONFIG_MOUSE_PS2_SYNAPTICS */ | |
| #ifdef CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS | |
| /* | |
| * The newest Synaptics device can use a secondary bus (called InterTouch) which | |
| * provides a better bandwidth and allow a better control of the touchpads. | |
| * This is used to decide if we need to use this bus or not. | |
| */ | |
| enum { | |
| SYNAPTICS_INTERTOUCH_NOT_SET = -1, | |
| SYNAPTICS_INTERTOUCH_OFF, | |
| SYNAPTICS_INTERTOUCH_ON, | |
| }; | |
| static int synaptics_intertouch = IS_ENABLED(CONFIG_RMI4_SMB) ? | |
| SYNAPTICS_INTERTOUCH_NOT_SET : SYNAPTICS_INTERTOUCH_OFF; | |
| module_param_named(synaptics_intertouch, synaptics_intertouch, int, 0644); | |
| MODULE_PARM_DESC(synaptics_intertouch, "Use a secondary bus for the Synaptics device."); | |
| static int synaptics_create_intertouch(struct psmouse *psmouse, | |
| struct synaptics_device_info *info, | |
| bool leave_breadcrumbs) | |
| { | |
| bool topbuttonpad = | |
| psmouse_matches_pnp_id(psmouse, topbuttonpad_pnp_ids) && | |
| !SYN_CAP_EXT_BUTTONS_STICK(info->ext_cap_10); | |
| const struct rmi_device_platform_data pdata = { | |
| .sensor_pdata = { | |
| .sensor_type = rmi_sensor_touchpad, | |
| .axis_align.flip_y = true, | |
| .kernel_tracking = false, | |
| .topbuttonpad = topbuttonpad, | |
| }, | |
| .f30_data = { | |
| .buttonpad = SYN_CAP_CLICKPAD(info->ext_cap_0c), | |
| .trackstick_buttons = | |
| !!SYN_CAP_EXT_BUTTONS_STICK(info->ext_cap_10), | |
| }, | |
| }; | |
| const struct i2c_board_info intertouch_board = { | |
| I2C_BOARD_INFO("rmi4_smbus", 0x2c), | |
| .flags = I2C_CLIENT_HOST_NOTIFY, | |
| }; | |
| return psmouse_smbus_init(psmouse, &intertouch_board, | |
| &pdata, sizeof(pdata), true, | |
| leave_breadcrumbs); | |
| } | |
| /** | |
| * synaptics_setup_intertouch - called once the PS/2 devices are enumerated | |
| * and decides to instantiate a SMBus InterTouch device. | |
| */ | |
| static int synaptics_setup_intertouch(struct psmouse *psmouse, | |
| struct synaptics_device_info *info, | |
| bool leave_breadcrumbs) | |
| { | |
| int error; | |
| if (synaptics_intertouch == SYNAPTICS_INTERTOUCH_OFF) | |
| return -ENXIO; | |
| if (synaptics_intertouch == SYNAPTICS_INTERTOUCH_NOT_SET) { | |
| if (!psmouse_matches_pnp_id(psmouse, topbuttonpad_pnp_ids) && | |
| !psmouse_matches_pnp_id(psmouse, smbus_pnp_ids)) { | |
| if (!psmouse_matches_pnp_id(psmouse, forcepad_pnp_ids)) | |
| psmouse_info(psmouse, | |
| "Your touchpad (%s) says it can support a different bus. " | |
| "If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.\n", | |
| psmouse->ps2dev.serio->firmware_id); | |
| return -ENXIO; | |
| } | |
| } | |
| psmouse_info(psmouse, "Trying to set up SMBus access\n"); | |
| error = synaptics_create_intertouch(psmouse, info, leave_breadcrumbs); | |
| if (error) { | |
| if (error == -EAGAIN) | |
| psmouse_info(psmouse, "SMbus companion is not ready yet\n"); | |
| else | |
| psmouse_err(psmouse, "unable to create intertouch device\n"); | |
| return error; | |
| } | |
| return 0; | |
| } | |
| int synaptics_init_smbus(struct psmouse *psmouse) | |
| { | |
| struct synaptics_device_info info; | |
| int error; | |
| psmouse_reset(psmouse); | |
| error = synaptics_query_hardware(psmouse, &info); | |
| if (error) { | |
| psmouse_err(psmouse, "Unable to query device: %d\n", error); | |
| return error; | |
| } | |
| if (!SYN_CAP_INTERTOUCH(info.ext_cap_0c)) | |
| return -ENXIO; | |
| return synaptics_create_intertouch(psmouse, &info, false); | |
| } | |
| #else /* CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS */ | |
| static int __maybe_unused | |
| synaptics_setup_intertouch(struct psmouse *psmouse, | |
| struct synaptics_device_info *info, | |
| bool leave_breadcrumbs) | |
| { | |
| return -ENOSYS; | |
| } | |
| int synaptics_init_smbus(struct psmouse *psmouse) | |
| { | |
| return -ENOSYS; | |
| } | |
| #endif /* CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS */ | |
| #if defined(CONFIG_MOUSE_PS2_SYNAPTICS) || \ | |
| defined(CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS) | |
| int synaptics_init(struct psmouse *psmouse) | |
| { | |
| struct synaptics_device_info info; | |
| int error; | |
| int retval; | |
| psmouse_reset(psmouse); | |
| error = synaptics_query_hardware(psmouse, &info); | |
| if (error) { | |
| psmouse_err(psmouse, "Unable to query device: %d\n", error); | |
| return error; | |
| } | |
| if (SYN_CAP_INTERTOUCH(info.ext_cap_0c)) { | |
| if ((!IS_ENABLED(CONFIG_RMI4_SMB) || | |
| !IS_ENABLED(CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS)) && | |
| /* Forcepads need F21, which is not ready */ | |
| !psmouse_matches_pnp_id(psmouse, forcepad_pnp_ids)) { | |
| psmouse_warn(psmouse, | |
| "The touchpad can support a better bus than the too old PS/2 protocol. " | |
| "Make sure MOUSE_PS2_SYNAPTICS_SMBUS and RMI4_SMB are enabled to get a better touchpad experience.\n"); | |
| } | |
| error = synaptics_setup_intertouch(psmouse, &info, true); | |
| if (!error) | |
| return PSMOUSE_SYNAPTICS_SMBUS; | |
| } | |
| retval = synaptics_setup_ps2(psmouse, &info); | |
| if (retval < 0) { | |
| /* | |
| * Not using any flavor of Synaptics support, so clean up | |
| * SMbus breadcrumbs, if any. | |
| */ | |
| psmouse_smbus_cleanup(psmouse); | |
| } | |
| return retval; | |
| } | |
| #else /* CONFIG_MOUSE_PS2_SYNAPTICS || CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS */ | |
| int synaptics_init(struct psmouse *psmouse) | |
| { | |
| return -ENOSYS; | |
| } | |
| #endif /* CONFIG_MOUSE_PS2_SYNAPTICS || CONFIG_MOUSE_PS2_SYNAPTICS_SMBUS */ |