patches.zynq/0018-tty-xuartps-Implement-BREAK-detection-add-SYSRQ-supp.patch

From dda80081e00ca6472b11591293a7c46cb7ef6527 Mon Sep 17 00:00:00 2001
From: Vlad Lungu <vlad.lungu@windriver.com>
Date: Thu, 17 Oct 2013 14:08:06 -0700
Subject: tty: xuartps: Implement BREAK detection, add SYSRQ support

The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.

Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 0c0c47bc40a2e358d593b2d7fb93b50027fbfc0c)
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@toshiba.co.jp>
Signed-off-by: Yoshitake Kobayashi <yoshitake.kobayashi@toshiba.co.jp>
---
 drivers/tty/serial/xilinx_uartps.c | 50 +++++++++++++++++++++++++++++++++++++-
 1 file changed, 49 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 2b3fe10362ba..2f94b8b2512e 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -11,13 +11,17 @@
  *
  */
 
+#if defined(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
 #include <linux/platform_device.h>
 #include <linux/serial.h>
+#include <linux/console.h>
 #include <linux/serial_core.h>
 #include <linux/slab.h>
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
-#include <linux/console.h>
 #include <linux/clk.h>
 #include <linux/irq.h>
 #include <linux/io.h>
@@ -128,6 +132,9 @@
 #define XUARTPS_IXR_RXEMPTY	0x00000002 /* RX FIFO empty interrupt. */
 #define XUARTPS_IXR_MASK	0x00001FFF /* Valid bit mask */
 
+/* Goes in read_status_mask for break detection as the HW doesn't do it*/
+#define XUARTPS_IXR_BRK		0x80000000
+
 /** Channel Status Register
  *
  * The channel status register (CSR) is provided to enable the control logic
@@ -171,6 +178,23 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
 	 */
 	isrstatus = xuartps_readl(XUARTPS_ISR_OFFSET);
 
+	/*
+	 * There is no hardware break detection, so we interpret framing
+	 * error with all-zeros data as a break sequence. Most of the time,
+	 * there's another non-zero byte at the end of the sequence.
+	 */
+
+	if (isrstatus & XUARTPS_IXR_FRAMING) {
+		while (!(xuartps_readl(XUARTPS_SR_OFFSET) &
+					XUARTPS_SR_RXEMPTY)) {
+			if (!xuartps_readl(XUARTPS_FIFO_OFFSET)) {
+				port->read_status_mask |= XUARTPS_IXR_BRK;
+				isrstatus &= ~XUARTPS_IXR_FRAMING;
+			}
+		}
+		xuartps_writel(XUARTPS_IXR_FRAMING, XUARTPS_ISR_OFFSET);
+	}
+
 	/* drop byte with parity error if IGNPAR specified */
 	if (isrstatus & port->ignore_status_mask & XUARTPS_IXR_PARITY)
 		isrstatus &= ~(XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT);
@@ -184,6 +208,30 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
 		while ((xuartps_readl(XUARTPS_SR_OFFSET) &
 			XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
 			data = xuartps_readl(XUARTPS_FIFO_OFFSET);
+
+			/* Non-NULL byte after BREAK is garbage (99%) */
+			if (data && (port->read_status_mask &
+						XUARTPS_IXR_BRK)) {
+				port->read_status_mask &= ~XUARTPS_IXR_BRK;
+				port->icount.brk++;
+				if (uart_handle_break(port))
+					continue;
+			}
+
+			/*
+			 * uart_handle_sysrq_char() doesn't work if
+			 * spinlocked, for some reason
+			 */
+			 if (port->sysrq) {
+				spin_unlock(&port->lock);
+				if (uart_handle_sysrq_char(port,
+							(unsigned char)data)) {
+					spin_lock(&port->lock);
+					continue;
+				}
+				spin_lock(&port->lock);
+			}
+
 			port->icount.rx++;
 
 			if (isrstatus & XUARTPS_IXR_PARITY) {
-- 
1.8.5.rc3