|  | // SPDX-License-Identifier: GPL-2.0-or-later | 
|  | /* | 
|  | * GPIO Chip driver for Analog Devices | 
|  | * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller | 
|  | * | 
|  | * Copyright 2009-2010 Analog Devices Inc. | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/gpio/driver.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/irq.h> | 
|  | #include <linux/of_device.h> | 
|  |  | 
|  | #include <linux/platform_data/adp5588.h> | 
|  |  | 
|  | #define DRV_NAME	"adp5588-gpio" | 
|  |  | 
|  | /* | 
|  | * Early pre 4.0 Silicon required to delay readout by at least 25ms, | 
|  | * since the Event Counter Register updated 25ms after the interrupt | 
|  | * asserted. | 
|  | */ | 
|  | #define WA_DELAYED_READOUT_REVID(rev)	((rev) < 4) | 
|  |  | 
|  | struct adp5588_gpio { | 
|  | struct i2c_client *client; | 
|  | struct gpio_chip gpio_chip; | 
|  | struct mutex lock;	/* protect cached dir, dat_out */ | 
|  | /* protect serialized access to the interrupt controller bus */ | 
|  | struct mutex irq_lock; | 
|  | uint8_t dat_out[3]; | 
|  | uint8_t dir[3]; | 
|  | uint8_t int_lvl_low[3]; | 
|  | uint8_t int_lvl_high[3]; | 
|  | uint8_t int_en[3]; | 
|  | uint8_t irq_mask[3]; | 
|  | uint8_t int_input_en[3]; | 
|  | }; | 
|  |  | 
|  | static int adp5588_gpio_read(struct i2c_client *client, u8 reg) | 
|  | { | 
|  | int ret = i2c_smbus_read_byte_data(client, reg); | 
|  |  | 
|  | if (ret < 0) | 
|  | dev_err(&client->dev, "Read Error\n"); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val) | 
|  | { | 
|  | int ret = i2c_smbus_write_byte_data(client, reg, val); | 
|  |  | 
|  | if (ret < 0) | 
|  | dev_err(&client->dev, "Write Error\n"); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off) | 
|  | { | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(chip); | 
|  | unsigned bank = ADP5588_BANK(off); | 
|  | unsigned bit = ADP5588_BIT(off); | 
|  | int val; | 
|  |  | 
|  | mutex_lock(&dev->lock); | 
|  |  | 
|  | if (dev->dir[bank] & bit) | 
|  | val = dev->dat_out[bank]; | 
|  | else | 
|  | val = adp5588_gpio_read(dev->client, GPIO_DAT_STAT1 + bank); | 
|  |  | 
|  | mutex_unlock(&dev->lock); | 
|  |  | 
|  | return !!(val & bit); | 
|  | } | 
|  |  | 
|  | static void adp5588_gpio_set_value(struct gpio_chip *chip, | 
|  | unsigned off, int val) | 
|  | { | 
|  | unsigned bank, bit; | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(chip); | 
|  |  | 
|  | bank = ADP5588_BANK(off); | 
|  | bit = ADP5588_BIT(off); | 
|  |  | 
|  | mutex_lock(&dev->lock); | 
|  | if (val) | 
|  | dev->dat_out[bank] |= bit; | 
|  | else | 
|  | dev->dat_out[bank] &= ~bit; | 
|  |  | 
|  | adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank, | 
|  | dev->dat_out[bank]); | 
|  | mutex_unlock(&dev->lock); | 
|  | } | 
|  |  | 
|  | static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off) | 
|  | { | 
|  | int ret; | 
|  | unsigned bank; | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(chip); | 
|  |  | 
|  | bank = ADP5588_BANK(off); | 
|  |  | 
|  | mutex_lock(&dev->lock); | 
|  | dev->dir[bank] &= ~ADP5588_BIT(off); | 
|  | ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]); | 
|  | mutex_unlock(&dev->lock); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int adp5588_gpio_direction_output(struct gpio_chip *chip, | 
|  | unsigned off, int val) | 
|  | { | 
|  | int ret; | 
|  | unsigned bank, bit; | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(chip); | 
|  |  | 
|  | bank = ADP5588_BANK(off); | 
|  | bit = ADP5588_BIT(off); | 
|  |  | 
|  | mutex_lock(&dev->lock); | 
|  | dev->dir[bank] |= bit; | 
|  |  | 
|  | if (val) | 
|  | dev->dat_out[bank] |= bit; | 
|  | else | 
|  | dev->dat_out[bank] &= ~bit; | 
|  |  | 
|  | ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank, | 
|  | dev->dat_out[bank]); | 
|  | ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, | 
|  | dev->dir[bank]); | 
|  | mutex_unlock(&dev->lock); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_GPIO_ADP5588_IRQ | 
|  |  | 
|  | static void adp5588_irq_bus_lock(struct irq_data *d) | 
|  | { | 
|  | struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(gc); | 
|  |  | 
|  | mutex_lock(&dev->irq_lock); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * genirq core code can issue chip->mask/unmask from atomic context. | 
|  | * This doesn't work for slow busses where an access needs to sleep. | 
|  | * bus_sync_unlock() is therefore called outside the atomic context, | 
|  | * syncs the current irq mask state with the slow external controller | 
|  | * and unlocks the bus. | 
|  | */ | 
|  |  | 
|  | static void adp5588_irq_bus_sync_unlock(struct irq_data *d) | 
|  | { | 
|  | struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(gc); | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { | 
|  | if (dev->int_input_en[i]) { | 
|  | mutex_lock(&dev->lock); | 
|  | dev->dir[i] &= ~dev->int_input_en[i]; | 
|  | dev->int_input_en[i] = 0; | 
|  | adp5588_gpio_write(dev->client, GPIO_DIR1 + i, | 
|  | dev->dir[i]); | 
|  | mutex_unlock(&dev->lock); | 
|  | } | 
|  |  | 
|  | if (dev->int_en[i] ^ dev->irq_mask[i]) { | 
|  | dev->int_en[i] = dev->irq_mask[i]; | 
|  | adp5588_gpio_write(dev->client, GPI_EM1 + i, | 
|  | dev->int_en[i]); | 
|  | } | 
|  | } | 
|  |  | 
|  | mutex_unlock(&dev->irq_lock); | 
|  | } | 
|  |  | 
|  | static void adp5588_irq_mask(struct irq_data *d) | 
|  | { | 
|  | struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(gc); | 
|  |  | 
|  | dev->irq_mask[ADP5588_BANK(d->hwirq)] &= ~ADP5588_BIT(d->hwirq); | 
|  | } | 
|  |  | 
|  | static void adp5588_irq_unmask(struct irq_data *d) | 
|  | { | 
|  | struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(gc); | 
|  |  | 
|  | dev->irq_mask[ADP5588_BANK(d->hwirq)] |= ADP5588_BIT(d->hwirq); | 
|  | } | 
|  |  | 
|  | static int adp5588_irq_set_type(struct irq_data *d, unsigned int type) | 
|  | { | 
|  | struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(gc); | 
|  | uint16_t gpio = d->hwirq; | 
|  | unsigned bank, bit; | 
|  |  | 
|  | bank = ADP5588_BANK(gpio); | 
|  | bit = ADP5588_BIT(gpio); | 
|  |  | 
|  | dev->int_lvl_low[bank] &= ~bit; | 
|  | dev->int_lvl_high[bank] &= ~bit; | 
|  |  | 
|  | if (type & IRQ_TYPE_EDGE_BOTH || type & IRQ_TYPE_LEVEL_HIGH) | 
|  | dev->int_lvl_high[bank] |= bit; | 
|  |  | 
|  | if (type & IRQ_TYPE_EDGE_BOTH || type & IRQ_TYPE_LEVEL_LOW) | 
|  | dev->int_lvl_low[bank] |= bit; | 
|  |  | 
|  | dev->int_input_en[bank] |= bit; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct irq_chip adp5588_irq_chip = { | 
|  | .name			= "adp5588", | 
|  | .irq_mask		= adp5588_irq_mask, | 
|  | .irq_unmask		= adp5588_irq_unmask, | 
|  | .irq_bus_lock		= adp5588_irq_bus_lock, | 
|  | .irq_bus_sync_unlock	= adp5588_irq_bus_sync_unlock, | 
|  | .irq_set_type		= adp5588_irq_set_type, | 
|  | }; | 
|  |  | 
|  | static irqreturn_t adp5588_irq_handler(int irq, void *devid) | 
|  | { | 
|  | struct adp5588_gpio *dev = devid; | 
|  | int status = adp5588_gpio_read(dev->client, INT_STAT); | 
|  |  | 
|  | if (status & ADP5588_KE_INT) { | 
|  | int ev_cnt = adp5588_gpio_read(dev->client, KEY_LCK_EC_STAT); | 
|  |  | 
|  | if (ev_cnt > 0) { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < (ev_cnt & ADP5588_KEC); i++) { | 
|  | int key = adp5588_gpio_read(dev->client, | 
|  | Key_EVENTA + i); | 
|  | /* GPIN events begin at 97, | 
|  | * bit 7 indicates logic level | 
|  | */ | 
|  | int gpio = (key & 0x7f) - 97; | 
|  | int lvl = key & (1 << 7); | 
|  | int bank = ADP5588_BANK(gpio); | 
|  | int bit = ADP5588_BIT(gpio); | 
|  |  | 
|  | if ((lvl && dev->int_lvl_high[bank] & bit) || | 
|  | (!lvl && dev->int_lvl_low[bank] & bit)) | 
|  | handle_nested_irq(irq_find_mapping( | 
|  | dev->gpio_chip.irq.domain, gpio)); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */ | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  |  | 
|  | static int adp5588_irq_init_hw(struct gpio_chip *gc) | 
|  | { | 
|  | struct adp5588_gpio *dev = gpiochip_get_data(gc); | 
|  | /* Enable IRQs after registering chip */ | 
|  | adp5588_gpio_write(dev->client, CFG, | 
|  | ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_KE_IEN); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adp5588_irq_setup(struct adp5588_gpio *dev) | 
|  | { | 
|  | struct i2c_client *client = dev->client; | 
|  | int ret; | 
|  | struct adp5588_gpio_platform_data *pdata = | 
|  | dev_get_platdata(&client->dev); | 
|  | struct gpio_irq_chip *girq; | 
|  |  | 
|  | adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC); | 
|  | adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */ | 
|  |  | 
|  | mutex_init(&dev->irq_lock); | 
|  |  | 
|  | ret = devm_request_threaded_irq(&client->dev, client->irq, | 
|  | NULL, adp5588_irq_handler, IRQF_ONESHOT | 
|  | | IRQF_TRIGGER_FALLING | IRQF_SHARED, | 
|  | dev_name(&client->dev), dev); | 
|  | if (ret) { | 
|  | dev_err(&client->dev, "failed to request irq %d\n", | 
|  | client->irq); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* This will be registered in the call to devm_gpiochip_add_data() */ | 
|  | girq = &dev->gpio_chip.irq; | 
|  | girq->chip = &adp5588_irq_chip; | 
|  | /* This will let us handle the parent IRQ in the driver */ | 
|  | girq->parent_handler = NULL; | 
|  | girq->num_parents = 0; | 
|  | girq->parents = NULL; | 
|  | girq->first = pdata ? pdata->irq_base : 0; | 
|  | girq->default_type = IRQ_TYPE_NONE; | 
|  | girq->handler = handle_simple_irq; | 
|  | girq->init_hw = adp5588_irq_init_hw; | 
|  | girq->threaded = true; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #else | 
|  | static int adp5588_irq_setup(struct adp5588_gpio *dev) | 
|  | { | 
|  | struct i2c_client *client = dev->client; | 
|  | dev_warn(&client->dev, "interrupt support not compiled in\n"); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #endif /* CONFIG_GPIO_ADP5588_IRQ */ | 
|  |  | 
|  | static int adp5588_gpio_probe(struct i2c_client *client) | 
|  | { | 
|  | struct adp5588_gpio_platform_data *pdata = | 
|  | dev_get_platdata(&client->dev); | 
|  | struct adp5588_gpio *dev; | 
|  | struct gpio_chip *gc; | 
|  | int ret, i, revid; | 
|  | unsigned int pullup_dis_mask = 0; | 
|  |  | 
|  | if (!i2c_check_functionality(client->adapter, | 
|  | I2C_FUNC_SMBUS_BYTE_DATA)) { | 
|  | dev_err(&client->dev, "SMBUS Byte Data not Supported\n"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL); | 
|  | if (!dev) | 
|  | return -ENOMEM; | 
|  |  | 
|  | dev->client = client; | 
|  |  | 
|  | gc = &dev->gpio_chip; | 
|  | gc->direction_input = adp5588_gpio_direction_input; | 
|  | gc->direction_output = adp5588_gpio_direction_output; | 
|  | gc->get = adp5588_gpio_get_value; | 
|  | gc->set = adp5588_gpio_set_value; | 
|  | gc->can_sleep = true; | 
|  | gc->base = -1; | 
|  | gc->parent = &client->dev; | 
|  |  | 
|  | if (pdata) { | 
|  | gc->base = pdata->gpio_start; | 
|  | gc->names = pdata->names; | 
|  | pullup_dis_mask = pdata->pullup_dis_mask; | 
|  | } | 
|  |  | 
|  | gc->ngpio = ADP5588_MAXGPIO; | 
|  | gc->label = client->name; | 
|  | gc->owner = THIS_MODULE; | 
|  |  | 
|  | mutex_init(&dev->lock); | 
|  |  | 
|  | ret = adp5588_gpio_read(dev->client, DEV_ID); | 
|  | if (ret < 0) | 
|  | return ret; | 
|  |  | 
|  | revid = ret & ADP5588_DEVICE_ID_MASK; | 
|  |  | 
|  | for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { | 
|  | dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i); | 
|  | dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i); | 
|  | ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0); | 
|  | ret |= adp5588_gpio_write(client, GPIO_PULL1 + i, | 
|  | (pullup_dis_mask >> (8 * i)) & 0xFF); | 
|  | ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0); | 
|  | if (ret) | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | if (client->irq) { | 
|  | if (WA_DELAYED_READOUT_REVID(revid)) { | 
|  | dev_warn(&client->dev, "GPIO int not supported\n"); | 
|  | } else { | 
|  | ret = adp5588_irq_setup(dev); | 
|  | if (ret) | 
|  | return ret; | 
|  | } | 
|  | } | 
|  |  | 
|  | ret = devm_gpiochip_add_data(&client->dev, &dev->gpio_chip, dev); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | if (pdata && pdata->setup) { | 
|  | ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context); | 
|  | if (ret < 0) | 
|  | dev_warn(&client->dev, "setup failed, %d\n", ret); | 
|  | } | 
|  |  | 
|  | i2c_set_clientdata(client, dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adp5588_gpio_remove(struct i2c_client *client) | 
|  | { | 
|  | struct adp5588_gpio_platform_data *pdata = | 
|  | dev_get_platdata(&client->dev); | 
|  | struct adp5588_gpio *dev = i2c_get_clientdata(client); | 
|  | int ret; | 
|  |  | 
|  | if (pdata && pdata->teardown) { | 
|  | ret = pdata->teardown(client, | 
|  | dev->gpio_chip.base, dev->gpio_chip.ngpio, | 
|  | pdata->context); | 
|  | if (ret < 0) { | 
|  | dev_err(&client->dev, "teardown failed %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (dev->client->irq) | 
|  | free_irq(dev->client->irq, dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct i2c_device_id adp5588_gpio_id[] = { | 
|  | {DRV_NAME, 0}, | 
|  | {} | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id); | 
|  |  | 
|  | #ifdef CONFIG_OF | 
|  | static const struct of_device_id adp5588_gpio_of_id[] = { | 
|  | { .compatible = "adi," DRV_NAME, }, | 
|  | {}, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, adp5588_gpio_of_id); | 
|  | #endif | 
|  |  | 
|  | static struct i2c_driver adp5588_gpio_driver = { | 
|  | .driver = { | 
|  | .name = DRV_NAME, | 
|  | .of_match_table = of_match_ptr(adp5588_gpio_of_id), | 
|  | }, | 
|  | .probe_new = adp5588_gpio_probe, | 
|  | .remove = adp5588_gpio_remove, | 
|  | .id_table = adp5588_gpio_id, | 
|  | }; | 
|  |  | 
|  | module_i2c_driver(adp5588_gpio_driver); | 
|  |  | 
|  | MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); | 
|  | MODULE_DESCRIPTION("GPIO ADP5588 Driver"); | 
|  | MODULE_LICENSE("GPL"); |