|  | /* | 
|  | * Sonics Silicon Backplane | 
|  | * SDIO-Hostbus related functions | 
|  | * | 
|  | * Copyright 2009 Albert Herranz <albert_herranz@yahoo.es> | 
|  | * | 
|  | * Based on drivers/ssb/pcmcia.c | 
|  | * Copyright 2006 Johannes Berg <johannes@sipsolutions.net> | 
|  | * Copyright 2007-2008 Michael Buesch <m@bues.ch> | 
|  | * | 
|  | * Licensed under the GNU/GPL. See COPYING for details. | 
|  | * | 
|  | */ | 
|  |  | 
|  | #include "ssb_private.h" | 
|  |  | 
|  | #include <linux/ssb/ssb.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/io.h> | 
|  | #include <linux/etherdevice.h> | 
|  | #include <linux/mmc/sdio_func.h> | 
|  |  | 
|  | /* Define the following to 1 to enable a printk on each coreswitch. */ | 
|  | #define SSB_VERBOSE_SDIOCORESWITCH_DEBUG		0 | 
|  |  | 
|  |  | 
|  | /* Hardware invariants CIS tuples */ | 
|  | #define SSB_SDIO_CIS			0x80 | 
|  | #define  SSB_SDIO_CIS_SROMREV		0x00 | 
|  | #define  SSB_SDIO_CIS_ID		0x01 | 
|  | #define  SSB_SDIO_CIS_BOARDREV		0x02 | 
|  | #define  SSB_SDIO_CIS_PA		0x03 | 
|  | #define   SSB_SDIO_CIS_PA_PA0B0_LO	0 | 
|  | #define   SSB_SDIO_CIS_PA_PA0B0_HI	1 | 
|  | #define   SSB_SDIO_CIS_PA_PA0B1_LO	2 | 
|  | #define   SSB_SDIO_CIS_PA_PA0B1_HI	3 | 
|  | #define   SSB_SDIO_CIS_PA_PA0B2_LO	4 | 
|  | #define   SSB_SDIO_CIS_PA_PA0B2_HI	5 | 
|  | #define   SSB_SDIO_CIS_PA_ITSSI		6 | 
|  | #define   SSB_SDIO_CIS_PA_MAXPOW	7 | 
|  | #define  SSB_SDIO_CIS_OEMNAME		0x04 | 
|  | #define  SSB_SDIO_CIS_CCODE		0x05 | 
|  | #define  SSB_SDIO_CIS_ANTENNA		0x06 | 
|  | #define  SSB_SDIO_CIS_ANTGAIN		0x07 | 
|  | #define  SSB_SDIO_CIS_BFLAGS		0x08 | 
|  | #define  SSB_SDIO_CIS_LEDS		0x09 | 
|  |  | 
|  | #define CISTPL_FUNCE_LAN_NODE_ID        0x04	/* same as in PCMCIA */ | 
|  |  | 
|  |  | 
|  | /* | 
|  | * Function 1 miscellaneous registers. | 
|  | * | 
|  | * Definitions match src/include/sbsdio.h from the | 
|  | * Android Open Source Project | 
|  | * http://android.git.kernel.org/?p=platform/system/wlan/broadcom.git | 
|  | * | 
|  | */ | 
|  | #define SBSDIO_FUNC1_SBADDRLOW	0x1000a	/* SB Address window Low (b15) */ | 
|  | #define SBSDIO_FUNC1_SBADDRMID	0x1000b	/* SB Address window Mid (b23-b16) */ | 
|  | #define SBSDIO_FUNC1_SBADDRHIGH	0x1000c	/* SB Address window High (b24-b31) */ | 
|  |  | 
|  | /* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */ | 
|  | #define SBSDIO_SBADDRLOW_MASK	0x80	/* Valid address bits in SBADDRLOW */ | 
|  | #define SBSDIO_SBADDRMID_MASK	0xff	/* Valid address bits in SBADDRMID */ | 
|  | #define SBSDIO_SBADDRHIGH_MASK	0xff	/* Valid address bits in SBADDRHIGH */ | 
|  |  | 
|  | #define SBSDIO_SB_OFT_ADDR_MASK	0x7FFF	/* sb offset addr is <= 15 bits, 32k */ | 
|  |  | 
|  | /* REVISIT: this flag doesn't seem to matter */ | 
|  | #define SBSDIO_SB_ACCESS_2_4B_FLAG	0x8000	/* forces 32-bit SB access */ | 
|  |  | 
|  |  | 
|  | /* | 
|  | * Address map within the SDIO function address space (128K). | 
|  | * | 
|  | *   Start   End     Description | 
|  | *   ------- ------- ------------------------------------------ | 
|  | *   0x00000 0x0ffff selected backplane address window (64K) | 
|  | *   0x10000 0x1ffff backplane control registers (max 64K) | 
|  | * | 
|  | * The current address window is configured by writing to registers | 
|  | * SBADDRLOW, SBADDRMID and SBADDRHIGH. | 
|  | * | 
|  | * In order to access the contents of a 32-bit Silicon Backplane address | 
|  | * the backplane address window must be first loaded with the highest | 
|  | * 16 bits of the target address. Then, an access must be done to the | 
|  | * SDIO function address space using the lower 15 bits of the address. | 
|  | * Bit 15 of the address must be set when doing 32 bit accesses. | 
|  | * | 
|  | * 10987654321098765432109876543210 | 
|  | * WWWWWWWWWWWWWWWWW                 SB Address Window | 
|  | *                 OOOOOOOOOOOOOOOO  Offset within SB Address Window | 
|  | *                 a                 32-bit access flag | 
|  | */ | 
|  |  | 
|  |  | 
|  | /* | 
|  | * SSB I/O via SDIO. | 
|  | * | 
|  | * NOTE: SDIO address @addr is 17 bits long (SDIO address space is 128K). | 
|  | */ | 
|  |  | 
|  | static inline struct device *ssb_sdio_dev(struct ssb_bus *bus) | 
|  | { | 
|  | return &bus->host_sdio->dev; | 
|  | } | 
|  |  | 
|  | /* host claimed */ | 
|  | static int ssb_sdio_writeb(struct ssb_bus *bus, unsigned int addr, u8 val) | 
|  | { | 
|  | int error = 0; | 
|  |  | 
|  | sdio_writeb(bus->host_sdio, val, addr, &error); | 
|  | if (unlikely(error)) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%08X <- %02x, error %d\n", | 
|  | addr, val, error); | 
|  | } | 
|  |  | 
|  | return error; | 
|  | } | 
|  |  | 
|  | #if 0 | 
|  | static u8 ssb_sdio_readb(struct ssb_bus *bus, unsigned int addr) | 
|  | { | 
|  | u8 val; | 
|  | int error = 0; | 
|  |  | 
|  | val = sdio_readb(bus->host_sdio, addr, &error); | 
|  | if (unlikely(error)) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%08X -> %02x, error %d\n", | 
|  | addr, val, error); | 
|  | } | 
|  |  | 
|  | return val; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | /* host claimed */ | 
|  | static int ssb_sdio_set_sbaddr_window(struct ssb_bus *bus, u32 address) | 
|  | { | 
|  | int error; | 
|  |  | 
|  | error = ssb_sdio_writeb(bus, SBSDIO_FUNC1_SBADDRLOW, | 
|  | (address >> 8) & SBSDIO_SBADDRLOW_MASK); | 
|  | if (error) | 
|  | goto out; | 
|  | error = ssb_sdio_writeb(bus, SBSDIO_FUNC1_SBADDRMID, | 
|  | (address >> 16) & SBSDIO_SBADDRMID_MASK); | 
|  | if (error) | 
|  | goto out; | 
|  | error = ssb_sdio_writeb(bus, SBSDIO_FUNC1_SBADDRHIGH, | 
|  | (address >> 24) & SBSDIO_SBADDRHIGH_MASK); | 
|  | if (error) | 
|  | goto out; | 
|  | bus->sdio_sbaddr = address; | 
|  | out: | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "failed to set address window" | 
|  | " to 0x%08x, error %d\n", address, error); | 
|  | } | 
|  |  | 
|  | return error; | 
|  | } | 
|  |  | 
|  | /* for enumeration use only */ | 
|  | u32 ssb_sdio_scan_read32(struct ssb_bus *bus, u16 offset) | 
|  | { | 
|  | u32 val; | 
|  | int error; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | val = sdio_readl(bus->host_sdio, offset, &error); | 
|  | sdio_release_host(bus->host_sdio); | 
|  | if (unlikely(error)) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %08x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  |  | 
|  | return val; | 
|  | } | 
|  |  | 
|  | /* for enumeration use only */ | 
|  | int ssb_sdio_scan_switch_coreidx(struct ssb_bus *bus, u8 coreidx) | 
|  | { | 
|  | u32 sbaddr; | 
|  | int error; | 
|  |  | 
|  | sbaddr = (coreidx * SSB_CORE_SIZE) + SSB_ENUM_BASE; | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | error = ssb_sdio_set_sbaddr_window(bus, sbaddr); | 
|  | sdio_release_host(bus->host_sdio); | 
|  | if (error) { | 
|  | dev_err(ssb_sdio_dev(bus), "failed to switch to core %u," | 
|  | " error %d\n", coreidx, error); | 
|  | goto out; | 
|  | } | 
|  | out: | 
|  | return error; | 
|  | } | 
|  |  | 
|  | /* host must be already claimed */ | 
|  | static int ssb_sdio_switch_core(struct ssb_bus *bus, struct ssb_device *dev) | 
|  | { | 
|  | u8 coreidx = dev->core_index; | 
|  | u32 sbaddr; | 
|  | int error = 0; | 
|  |  | 
|  | sbaddr = (coreidx * SSB_CORE_SIZE) + SSB_ENUM_BASE; | 
|  | if (unlikely(bus->sdio_sbaddr != sbaddr)) { | 
|  | #if SSB_VERBOSE_SDIOCORESWITCH_DEBUG | 
|  | dev_info(ssb_sdio_dev(bus), | 
|  | "switching to %s core, index %d\n", | 
|  | ssb_core_name(dev->id.coreid), coreidx); | 
|  | #endif | 
|  | error = ssb_sdio_set_sbaddr_window(bus, sbaddr); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "failed to switch to" | 
|  | " core %u, error %d\n", coreidx, error); | 
|  | goto out; | 
|  | } | 
|  | bus->mapped_device = dev; | 
|  | } | 
|  |  | 
|  | out: | 
|  | return error; | 
|  | } | 
|  |  | 
|  | static u8 ssb_sdio_read8(struct ssb_device *dev, u16 offset) | 
|  | { | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | u8 val = 0xff; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) | 
|  | goto out; | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  | val = sdio_readb(bus->host_sdio, offset, &error); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %02x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  |  | 
|  | return val; | 
|  | } | 
|  |  | 
|  | static u16 ssb_sdio_read16(struct ssb_device *dev, u16 offset) | 
|  | { | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | u16 val = 0xffff; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) | 
|  | goto out; | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  | val = sdio_readw(bus->host_sdio, offset, &error); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %04x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  |  | 
|  | return val; | 
|  | } | 
|  |  | 
|  | static u32 ssb_sdio_read32(struct ssb_device *dev, u16 offset) | 
|  | { | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | u32 val = 0xffffffff; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) | 
|  | goto out; | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  | offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */ | 
|  | val = sdio_readl(bus->host_sdio, offset, &error); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %08x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  |  | 
|  | return val; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_SSB_BLOCKIO | 
|  | static void ssb_sdio_block_read(struct ssb_device *dev, void *buffer, | 
|  | size_t count, u16 offset, u8 reg_width) | 
|  | { | 
|  | size_t saved_count = count; | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) { | 
|  | error = -EIO; | 
|  | memset(buffer, 0xff, count); | 
|  | goto err_out; | 
|  | } | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  |  | 
|  | switch (reg_width) { | 
|  | case sizeof(u8): { | 
|  | error = sdio_readsb(bus->host_sdio, buffer, offset, count); | 
|  | break; | 
|  | } | 
|  | case sizeof(u16): { | 
|  | WARN_ON(count & 1); | 
|  | error = sdio_readsb(bus->host_sdio, buffer, offset, count); | 
|  | break; | 
|  | } | 
|  | case sizeof(u32): { | 
|  | WARN_ON(count & 3); | 
|  | offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */ | 
|  | error = sdio_readsb(bus->host_sdio, buffer, offset, count); | 
|  | break; | 
|  | } | 
|  | default: | 
|  | WARN_ON(1); | 
|  | } | 
|  | if (!error) | 
|  | goto out; | 
|  |  | 
|  | err_out: | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X (width=%u, len=%zu), error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, reg_width, saved_count, error); | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  | } | 
|  | #endif /* CONFIG_SSB_BLOCKIO */ | 
|  |  | 
|  | static void ssb_sdio_write8(struct ssb_device *dev, u16 offset, u8 val) | 
|  | { | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) | 
|  | goto out; | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  | sdio_writeb(bus->host_sdio, val, offset, &error); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %02x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  | } | 
|  |  | 
|  | static void ssb_sdio_write16(struct ssb_device *dev, u16 offset, u16 val) | 
|  | { | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) | 
|  | goto out; | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  | sdio_writew(bus->host_sdio, val, offset, &error); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %04x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  | } | 
|  |  | 
|  | static void ssb_sdio_write32(struct ssb_device *dev, u16 offset, u32 val) | 
|  | { | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) | 
|  | goto out; | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  | offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */ | 
|  | sdio_writel(bus->host_sdio, val, offset, &error); | 
|  | if (error) { | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %08x, error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, val, error); | 
|  | } | 
|  | if (bus->quirks & SSB_QUIRK_SDIO_READ_AFTER_WRITE32) | 
|  | sdio_readl(bus->host_sdio, 0, &error); | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_SSB_BLOCKIO | 
|  | static void ssb_sdio_block_write(struct ssb_device *dev, const void *buffer, | 
|  | size_t count, u16 offset, u8 reg_width) | 
|  | { | 
|  | size_t saved_count = count; | 
|  | struct ssb_bus *bus = dev->bus; | 
|  | int error = 0; | 
|  |  | 
|  | sdio_claim_host(bus->host_sdio); | 
|  | if (unlikely(ssb_sdio_switch_core(bus, dev))) { | 
|  | error = -EIO; | 
|  | goto err_out; | 
|  | } | 
|  | offset |= bus->sdio_sbaddr & 0xffff; | 
|  | offset &= SBSDIO_SB_OFT_ADDR_MASK; | 
|  |  | 
|  | switch (reg_width) { | 
|  | case sizeof(u8): | 
|  | error = sdio_writesb(bus->host_sdio, offset, | 
|  | (void *)buffer, count); | 
|  | break; | 
|  | case sizeof(u16): | 
|  | WARN_ON(count & 1); | 
|  | error = sdio_writesb(bus->host_sdio, offset, | 
|  | (void *)buffer, count); | 
|  | break; | 
|  | case sizeof(u32): | 
|  | WARN_ON(count & 3); | 
|  | offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */ | 
|  | error = sdio_writesb(bus->host_sdio, offset, | 
|  | (void *)buffer, count); | 
|  | break; | 
|  | default: | 
|  | WARN_ON(1); | 
|  | } | 
|  | if (!error) | 
|  | goto out; | 
|  |  | 
|  | err_out: | 
|  | dev_dbg(ssb_sdio_dev(bus), "%04X:%04X (width=%u, len=%zu), error %d\n", | 
|  | bus->sdio_sbaddr >> 16, offset, reg_width, saved_count, error); | 
|  | out: | 
|  | sdio_release_host(bus->host_sdio); | 
|  | } | 
|  |  | 
|  | #endif /* CONFIG_SSB_BLOCKIO */ | 
|  |  | 
|  | /* Not "static", as it's used in main.c */ | 
|  | const struct ssb_bus_ops ssb_sdio_ops = { | 
|  | .read8		= ssb_sdio_read8, | 
|  | .read16		= ssb_sdio_read16, | 
|  | .read32		= ssb_sdio_read32, | 
|  | .write8		= ssb_sdio_write8, | 
|  | .write16	= ssb_sdio_write16, | 
|  | .write32	= ssb_sdio_write32, | 
|  | #ifdef CONFIG_SSB_BLOCKIO | 
|  | .block_read	= ssb_sdio_block_read, | 
|  | .block_write	= ssb_sdio_block_write, | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | #define GOTO_ERROR_ON(condition, description) do {	\ | 
|  | if (unlikely(condition)) {			\ | 
|  | error_description = description;	\ | 
|  | goto error;				\ | 
|  | }						\ | 
|  | } while (0) | 
|  |  | 
|  | int ssb_sdio_get_invariants(struct ssb_bus *bus, | 
|  | struct ssb_init_invariants *iv) | 
|  | { | 
|  | struct ssb_sprom *sprom = &iv->sprom; | 
|  | struct ssb_boardinfo *bi = &iv->boardinfo; | 
|  | const char *error_description = "none"; | 
|  | struct sdio_func_tuple *tuple; | 
|  | void *mac; | 
|  |  | 
|  | memset(sprom, 0xFF, sizeof(*sprom)); | 
|  | sprom->boardflags_lo = 0; | 
|  | sprom->boardflags_hi = 0; | 
|  |  | 
|  | tuple = bus->host_sdio->tuples; | 
|  | while (tuple) { | 
|  | switch (tuple->code) { | 
|  | case 0x22: /* extended function */ | 
|  | switch (tuple->data[0]) { | 
|  | case CISTPL_FUNCE_LAN_NODE_ID: | 
|  | GOTO_ERROR_ON((tuple->size != 7) && | 
|  | (tuple->data[1] != 6), | 
|  | "mac tpl size"); | 
|  | /* fetch the MAC address. */ | 
|  | mac = tuple->data + 2; | 
|  | memcpy(sprom->il0mac, mac, ETH_ALEN); | 
|  | memcpy(sprom->et1mac, mac, ETH_ALEN); | 
|  | break; | 
|  | default: | 
|  | break; | 
|  | } | 
|  | break; | 
|  | case 0x80: /* vendor specific tuple */ | 
|  | switch (tuple->data[0]) { | 
|  | case SSB_SDIO_CIS_SROMREV: | 
|  | GOTO_ERROR_ON(tuple->size != 2, | 
|  | "sromrev tpl size"); | 
|  | sprom->revision = tuple->data[1]; | 
|  | break; | 
|  | case SSB_SDIO_CIS_ID: | 
|  | GOTO_ERROR_ON((tuple->size != 5) && | 
|  | (tuple->size != 7), | 
|  | "id tpl size"); | 
|  | bi->vendor = tuple->data[1] | | 
|  | (tuple->data[2]<<8); | 
|  | break; | 
|  | case SSB_SDIO_CIS_BOARDREV: | 
|  | GOTO_ERROR_ON(tuple->size != 2, | 
|  | "boardrev tpl size"); | 
|  | sprom->board_rev = tuple->data[1]; | 
|  | break; | 
|  | case SSB_SDIO_CIS_PA: | 
|  | GOTO_ERROR_ON((tuple->size != 9) && | 
|  | (tuple->size != 10), | 
|  | "pa tpl size"); | 
|  | sprom->pa0b0 = tuple->data[1] | | 
|  | ((u16)tuple->data[2] << 8); | 
|  | sprom->pa0b1 = tuple->data[3] | | 
|  | ((u16)tuple->data[4] << 8); | 
|  | sprom->pa0b2 = tuple->data[5] | | 
|  | ((u16)tuple->data[6] << 8); | 
|  | sprom->itssi_a = tuple->data[7]; | 
|  | sprom->itssi_bg = tuple->data[7]; | 
|  | sprom->maxpwr_a = tuple->data[8]; | 
|  | sprom->maxpwr_bg = tuple->data[8]; | 
|  | break; | 
|  | case SSB_SDIO_CIS_OEMNAME: | 
|  | /* Not present */ | 
|  | break; | 
|  | case SSB_SDIO_CIS_CCODE: | 
|  | GOTO_ERROR_ON(tuple->size != 2, | 
|  | "ccode tpl size"); | 
|  | sprom->country_code = tuple->data[1]; | 
|  | break; | 
|  | case SSB_SDIO_CIS_ANTENNA: | 
|  | GOTO_ERROR_ON(tuple->size != 2, | 
|  | "ant tpl size"); | 
|  | sprom->ant_available_a = tuple->data[1]; | 
|  | sprom->ant_available_bg = tuple->data[1]; | 
|  | break; | 
|  | case SSB_SDIO_CIS_ANTGAIN: | 
|  | GOTO_ERROR_ON(tuple->size != 2, | 
|  | "antg tpl size"); | 
|  | sprom->antenna_gain.a0 = tuple->data[1]; | 
|  | sprom->antenna_gain.a1 = tuple->data[1]; | 
|  | sprom->antenna_gain.a2 = tuple->data[1]; | 
|  | sprom->antenna_gain.a3 = tuple->data[1]; | 
|  | break; | 
|  | case SSB_SDIO_CIS_BFLAGS: | 
|  | GOTO_ERROR_ON((tuple->size != 3) && | 
|  | (tuple->size != 5), | 
|  | "bfl tpl size"); | 
|  | sprom->boardflags_lo = tuple->data[1] | | 
|  | ((u16)tuple->data[2] << 8); | 
|  | break; | 
|  | case SSB_SDIO_CIS_LEDS: | 
|  | GOTO_ERROR_ON(tuple->size != 5, | 
|  | "leds tpl size"); | 
|  | sprom->gpio0 = tuple->data[1]; | 
|  | sprom->gpio1 = tuple->data[2]; | 
|  | sprom->gpio2 = tuple->data[3]; | 
|  | sprom->gpio3 = tuple->data[4]; | 
|  | break; | 
|  | default: | 
|  | break; | 
|  | } | 
|  | break; | 
|  | default: | 
|  | break; | 
|  | } | 
|  | tuple = tuple->next; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | error: | 
|  | dev_err(ssb_sdio_dev(bus), "failed to fetch device invariants: %s\n", | 
|  | error_description); | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | void ssb_sdio_exit(struct ssb_bus *bus) | 
|  | { | 
|  | if (bus->bustype != SSB_BUSTYPE_SDIO) | 
|  | return; | 
|  | /* Nothing to do here. */ | 
|  | } | 
|  |  | 
|  | int ssb_sdio_init(struct ssb_bus *bus) | 
|  | { | 
|  | if (bus->bustype != SSB_BUSTYPE_SDIO) | 
|  | return 0; | 
|  |  | 
|  | bus->sdio_sbaddr = ~0; | 
|  |  | 
|  | return 0; | 
|  | } |