|  | // SPDX-License-Identifier: GPL-2.0 | 
|  | /** | 
|  | * uniphier_thermal.c - Socionext UniPhier thermal driver | 
|  | * Copyright 2014      Panasonic Corporation | 
|  | * Copyright 2016-2017 Socionext Inc. | 
|  | * Author: | 
|  | *	Kunihiko Hayashi <hayashi.kunihiko@socionext.com> | 
|  | */ | 
|  |  | 
|  | #include <linux/bitops.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/mfd/syscon.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/of.h> | 
|  | #include <linux/of_device.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/regmap.h> | 
|  | #include <linux/thermal.h> | 
|  |  | 
|  | #include "thermal_core.h" | 
|  |  | 
|  | /* | 
|  | * block registers | 
|  | * addresses are the offset from .block_base | 
|  | */ | 
|  | #define PVTCTLEN			0x0000 | 
|  | #define PVTCTLEN_EN			BIT(0) | 
|  |  | 
|  | #define PVTCTLMODE			0x0004 | 
|  | #define PVTCTLMODE_MASK			0xf | 
|  | #define PVTCTLMODE_TEMPMON		0x5 | 
|  |  | 
|  | #define EMONREPEAT			0x0040 | 
|  | #define EMONREPEAT_ENDLESS		BIT(24) | 
|  | #define EMONREPEAT_PERIOD		GENMASK(3, 0) | 
|  | #define EMONREPEAT_PERIOD_1000000	0x9 | 
|  |  | 
|  | /* | 
|  | * common registers | 
|  | * addresses are the offset from .map_base | 
|  | */ | 
|  | #define PVTCTLSEL			0x0900 | 
|  | #define PVTCTLSEL_MASK			GENMASK(2, 0) | 
|  | #define PVTCTLSEL_MONITOR		0 | 
|  |  | 
|  | #define SETALERT0			0x0910 | 
|  | #define SETALERT1			0x0914 | 
|  | #define SETALERT2			0x0918 | 
|  | #define SETALERT_TEMP_OVF		(GENMASK(7, 0) << 16) | 
|  | #define SETALERT_TEMP_OVF_VALUE(val)	(((val) & GENMASK(7, 0)) << 16) | 
|  | #define SETALERT_EN			BIT(0) | 
|  |  | 
|  | #define PMALERTINTCTL			0x0920 | 
|  | #define PMALERTINTCTL_CLR(ch)		BIT(4 * (ch) + 2) | 
|  | #define PMALERTINTCTL_SET(ch)		BIT(4 * (ch) + 1) | 
|  | #define PMALERTINTCTL_EN(ch)		BIT(4 * (ch) + 0) | 
|  | #define PMALERTINTCTL_MASK		(GENMASK(10, 8) | GENMASK(6, 4) | \ | 
|  | GENMASK(2, 0)) | 
|  |  | 
|  | #define TMOD				0x0928 | 
|  | #define TMOD_WIDTH			9 | 
|  |  | 
|  | #define TMODCOEF			0x0e5c | 
|  |  | 
|  | #define TMODSETUP0_EN			BIT(30) | 
|  | #define TMODSETUP0_VAL(val)		(((val) & GENMASK(13, 0)) << 16) | 
|  | #define TMODSETUP1_EN			BIT(15) | 
|  | #define TMODSETUP1_VAL(val)		((val) & GENMASK(14, 0)) | 
|  |  | 
|  | /* SoC critical temperature */ | 
|  | #define CRITICAL_TEMP_LIMIT		(120 * 1000) | 
|  |  | 
|  | /* Max # of alert channels */ | 
|  | #define ALERT_CH_NUM			3 | 
|  |  | 
|  | /* SoC specific thermal sensor data */ | 
|  | struct uniphier_tm_soc_data { | 
|  | u32 map_base; | 
|  | u32 block_base; | 
|  | u32 tmod_setup_addr; | 
|  | }; | 
|  |  | 
|  | struct uniphier_tm_dev { | 
|  | struct regmap *regmap; | 
|  | struct device *dev; | 
|  | bool alert_en[ALERT_CH_NUM]; | 
|  | struct thermal_zone_device *tz_dev; | 
|  | const struct uniphier_tm_soc_data *data; | 
|  | }; | 
|  |  | 
|  | static int uniphier_tm_initialize_sensor(struct uniphier_tm_dev *tdev) | 
|  | { | 
|  | struct regmap *map = tdev->regmap; | 
|  | u32 val; | 
|  | u32 tmod_calib[2]; | 
|  | int ret; | 
|  |  | 
|  | /* stop PVT */ | 
|  | regmap_write_bits(map, tdev->data->block_base + PVTCTLEN, | 
|  | PVTCTLEN_EN, 0); | 
|  |  | 
|  | /* | 
|  | * Since SoC has a calibrated value that was set in advance, | 
|  | * TMODCOEF shows non-zero and PVT refers the value internally. | 
|  | * | 
|  | * If TMODCOEF shows zero, the boards don't have the calibrated | 
|  | * value, and the driver has to set default value from DT. | 
|  | */ | 
|  | ret = regmap_read(map, tdev->data->map_base + TMODCOEF, &val); | 
|  | if (ret) | 
|  | return ret; | 
|  | if (!val) { | 
|  | /* look for the default values in DT */ | 
|  | ret = of_property_read_u32_array(tdev->dev->of_node, | 
|  | "socionext,tmod-calibration", | 
|  | tmod_calib, | 
|  | ARRAY_SIZE(tmod_calib)); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | regmap_write(map, tdev->data->tmod_setup_addr, | 
|  | TMODSETUP0_EN | TMODSETUP0_VAL(tmod_calib[0]) | | 
|  | TMODSETUP1_EN | TMODSETUP1_VAL(tmod_calib[1])); | 
|  | } | 
|  |  | 
|  | /* select temperature mode */ | 
|  | regmap_write_bits(map, tdev->data->block_base + PVTCTLMODE, | 
|  | PVTCTLMODE_MASK, PVTCTLMODE_TEMPMON); | 
|  |  | 
|  | /* set monitoring period */ | 
|  | regmap_write_bits(map, tdev->data->block_base + EMONREPEAT, | 
|  | EMONREPEAT_ENDLESS | EMONREPEAT_PERIOD, | 
|  | EMONREPEAT_ENDLESS | EMONREPEAT_PERIOD_1000000); | 
|  |  | 
|  | /* set monitor mode */ | 
|  | regmap_write_bits(map, tdev->data->map_base + PVTCTLSEL, | 
|  | PVTCTLSEL_MASK, PVTCTLSEL_MONITOR); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void uniphier_tm_set_alert(struct uniphier_tm_dev *tdev, u32 ch, | 
|  | u32 temp) | 
|  | { | 
|  | struct regmap *map = tdev->regmap; | 
|  |  | 
|  | /* set alert temperature */ | 
|  | regmap_write_bits(map, tdev->data->map_base + SETALERT0 + (ch << 2), | 
|  | SETALERT_EN | SETALERT_TEMP_OVF, | 
|  | SETALERT_EN | | 
|  | SETALERT_TEMP_OVF_VALUE(temp / 1000)); | 
|  | } | 
|  |  | 
|  | static void uniphier_tm_enable_sensor(struct uniphier_tm_dev *tdev) | 
|  | { | 
|  | struct regmap *map = tdev->regmap; | 
|  | int i; | 
|  | u32 bits = 0; | 
|  |  | 
|  | for (i = 0; i < ALERT_CH_NUM; i++) | 
|  | if (tdev->alert_en[i]) | 
|  | bits |= PMALERTINTCTL_EN(i); | 
|  |  | 
|  | /* enable alert interrupt */ | 
|  | regmap_write_bits(map, tdev->data->map_base + PMALERTINTCTL, | 
|  | PMALERTINTCTL_MASK, bits); | 
|  |  | 
|  | /* start PVT */ | 
|  | regmap_write_bits(map, tdev->data->block_base + PVTCTLEN, | 
|  | PVTCTLEN_EN, PVTCTLEN_EN); | 
|  |  | 
|  | usleep_range(700, 1500);	/* The spec note says at least 700us */ | 
|  | } | 
|  |  | 
|  | static void uniphier_tm_disable_sensor(struct uniphier_tm_dev *tdev) | 
|  | { | 
|  | struct regmap *map = tdev->regmap; | 
|  |  | 
|  | /* disable alert interrupt */ | 
|  | regmap_write_bits(map, tdev->data->map_base + PMALERTINTCTL, | 
|  | PMALERTINTCTL_MASK, 0); | 
|  |  | 
|  | /* stop PVT */ | 
|  | regmap_write_bits(map, tdev->data->block_base + PVTCTLEN, | 
|  | PVTCTLEN_EN, 0); | 
|  |  | 
|  | usleep_range(1000, 2000);	/* The spec note says at least 1ms */ | 
|  | } | 
|  |  | 
|  | static int uniphier_tm_get_temp(void *data, int *out_temp) | 
|  | { | 
|  | struct uniphier_tm_dev *tdev = data; | 
|  | struct regmap *map = tdev->regmap; | 
|  | int ret; | 
|  | u32 temp; | 
|  |  | 
|  | ret = regmap_read(map, tdev->data->map_base + TMOD, &temp); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | /* MSB of the TMOD field is a sign bit */ | 
|  | *out_temp = sign_extend32(temp, TMOD_WIDTH - 1) * 1000; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct thermal_zone_of_device_ops uniphier_of_thermal_ops = { | 
|  | .get_temp = uniphier_tm_get_temp, | 
|  | }; | 
|  |  | 
|  | static void uniphier_tm_irq_clear(struct uniphier_tm_dev *tdev) | 
|  | { | 
|  | u32 mask = 0, bits = 0; | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < ALERT_CH_NUM; i++) { | 
|  | mask |= (PMALERTINTCTL_CLR(i) | PMALERTINTCTL_SET(i)); | 
|  | bits |= PMALERTINTCTL_CLR(i); | 
|  | } | 
|  |  | 
|  | /* clear alert interrupt */ | 
|  | regmap_write_bits(tdev->regmap, | 
|  | tdev->data->map_base + PMALERTINTCTL, mask, bits); | 
|  | } | 
|  |  | 
|  | static irqreturn_t uniphier_tm_alarm_irq(int irq, void *_tdev) | 
|  | { | 
|  | struct uniphier_tm_dev *tdev = _tdev; | 
|  |  | 
|  | disable_irq_nosync(irq); | 
|  | uniphier_tm_irq_clear(tdev); | 
|  |  | 
|  | return IRQ_WAKE_THREAD; | 
|  | } | 
|  |  | 
|  | static irqreturn_t uniphier_tm_alarm_irq_thread(int irq, void *_tdev) | 
|  | { | 
|  | struct uniphier_tm_dev *tdev = _tdev; | 
|  |  | 
|  | thermal_zone_device_update(tdev->tz_dev, THERMAL_EVENT_UNSPECIFIED); | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static int uniphier_tm_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct device *dev = &pdev->dev; | 
|  | struct regmap *regmap; | 
|  | struct device_node *parent; | 
|  | struct uniphier_tm_dev *tdev; | 
|  | const struct thermal_trip *trips; | 
|  | int i, ret, irq, ntrips, crit_temp = INT_MAX; | 
|  |  | 
|  | tdev = devm_kzalloc(dev, sizeof(*tdev), GFP_KERNEL); | 
|  | if (!tdev) | 
|  | return -ENOMEM; | 
|  | tdev->dev = dev; | 
|  |  | 
|  | tdev->data = of_device_get_match_data(dev); | 
|  | if (WARN_ON(!tdev->data)) | 
|  | return -EINVAL; | 
|  |  | 
|  | irq = platform_get_irq(pdev, 0); | 
|  | if (irq < 0) | 
|  | return irq; | 
|  |  | 
|  | /* get regmap from syscon node */ | 
|  | parent = of_get_parent(dev->of_node); /* parent should be syscon node */ | 
|  | regmap = syscon_node_to_regmap(parent); | 
|  | of_node_put(parent); | 
|  | if (IS_ERR(regmap)) { | 
|  | dev_err(dev, "failed to get regmap (error %ld)\n", | 
|  | PTR_ERR(regmap)); | 
|  | return PTR_ERR(regmap); | 
|  | } | 
|  | tdev->regmap = regmap; | 
|  |  | 
|  | ret = uniphier_tm_initialize_sensor(tdev); | 
|  | if (ret) { | 
|  | dev_err(dev, "failed to initialize sensor\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | ret = devm_request_threaded_irq(dev, irq, uniphier_tm_alarm_irq, | 
|  | uniphier_tm_alarm_irq_thread, | 
|  | 0, "thermal", tdev); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | platform_set_drvdata(pdev, tdev); | 
|  |  | 
|  | tdev->tz_dev = devm_thermal_zone_of_sensor_register(dev, 0, tdev, | 
|  | &uniphier_of_thermal_ops); | 
|  | if (IS_ERR(tdev->tz_dev)) { | 
|  | dev_err(dev, "failed to register sensor device\n"); | 
|  | return PTR_ERR(tdev->tz_dev); | 
|  | } | 
|  |  | 
|  | /* get trip points */ | 
|  | trips = of_thermal_get_trip_points(tdev->tz_dev); | 
|  | ntrips = of_thermal_get_ntrips(tdev->tz_dev); | 
|  | if (ntrips > ALERT_CH_NUM) { | 
|  | dev_err(dev, "thermal zone has too many trips\n"); | 
|  | return -E2BIG; | 
|  | } | 
|  |  | 
|  | /* set alert temperatures */ | 
|  | for (i = 0; i < ntrips; i++) { | 
|  | if (trips[i].type == THERMAL_TRIP_CRITICAL && | 
|  | trips[i].temperature < crit_temp) | 
|  | crit_temp = trips[i].temperature; | 
|  | uniphier_tm_set_alert(tdev, i, trips[i].temperature); | 
|  | tdev->alert_en[i] = true; | 
|  | } | 
|  | if (crit_temp > CRITICAL_TEMP_LIMIT) { | 
|  | dev_err(dev, "critical trip is over limit(>%d), or not set\n", | 
|  | CRITICAL_TEMP_LIMIT); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | uniphier_tm_enable_sensor(tdev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int uniphier_tm_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct uniphier_tm_dev *tdev = platform_get_drvdata(pdev); | 
|  |  | 
|  | /* disable sensor */ | 
|  | uniphier_tm_disable_sensor(tdev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct uniphier_tm_soc_data uniphier_pxs2_tm_data = { | 
|  | .map_base        = 0xe000, | 
|  | .block_base      = 0xe000, | 
|  | .tmod_setup_addr = 0xe904, | 
|  | }; | 
|  |  | 
|  | static const struct uniphier_tm_soc_data uniphier_ld20_tm_data = { | 
|  | .map_base        = 0xe000, | 
|  | .block_base      = 0xe800, | 
|  | .tmod_setup_addr = 0xe938, | 
|  | }; | 
|  |  | 
|  | static const struct of_device_id uniphier_tm_dt_ids[] = { | 
|  | { | 
|  | .compatible = "socionext,uniphier-pxs2-thermal", | 
|  | .data       = &uniphier_pxs2_tm_data, | 
|  | }, | 
|  | { | 
|  | .compatible = "socionext,uniphier-ld20-thermal", | 
|  | .data       = &uniphier_ld20_tm_data, | 
|  | }, | 
|  | { | 
|  | .compatible = "socionext,uniphier-pxs3-thermal", | 
|  | .data       = &uniphier_ld20_tm_data, | 
|  | }, | 
|  | { /* sentinel */ } | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, uniphier_tm_dt_ids); | 
|  |  | 
|  | static struct platform_driver uniphier_tm_driver = { | 
|  | .probe = uniphier_tm_probe, | 
|  | .remove = uniphier_tm_remove, | 
|  | .driver = { | 
|  | .name = "uniphier-thermal", | 
|  | .of_match_table = uniphier_tm_dt_ids, | 
|  | }, | 
|  | }; | 
|  | module_platform_driver(uniphier_tm_driver); | 
|  |  | 
|  | MODULE_AUTHOR("Kunihiko Hayashi <hayashi.kunihiko@socionext.com>"); | 
|  | MODULE_DESCRIPTION("UniPhier thermal driver"); | 
|  | MODULE_LICENSE("GPL v2"); |