drivers/pinctrl/samsung/pinctrl-exynos.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Exynos specific definitions for Samsung pinctrl and gpiolib driver.
 *
 * Copyright (c) 2012 Samsung Electronics Co., Ltd.
 *		http://www.samsung.com
 * Copyright (c) 2012 Linaro Ltd
 *		http://www.linaro.org
 *
 * This file contains the Exynos specific definitions for the Samsung
 * pinctrl/gpiolib interface drivers.
 *
 * Author: Thomas Abraham <thomas.ab@samsung.com>
 */

#ifndef __PINCTRL_SAMSUNG_EXYNOS_H
#define __PINCTRL_SAMSUNG_EXYNOS_H

/* Values for the pin CON register */
#define EXYNOS_PIN_CON_FUNC_EINT	0xf

/* External GPIO and wakeup interrupt related definitions */
#define EXYNOS_GPIO_ECON_OFFSET		0x700
#define EXYNOS_GPIO_EFLTCON_OFFSET	0x800
#define EXYNOS_GPIO_EMASK_OFFSET	0x900
#define EXYNOS_GPIO_EPEND_OFFSET	0xA00
#define EXYNOS_WKUP_ECON_OFFSET		0xE00
#define EXYNOS_WKUP_EMASK_OFFSET	0xF00
#define EXYNOS_WKUP_EPEND_OFFSET	0xF40
#define EXYNOS7_WKUP_ECON_OFFSET	0x700
#define EXYNOS7_WKUP_EMASK_OFFSET	0x900
#define EXYNOS7_WKUP_EPEND_OFFSET	0xA00
#define EXYNOS_SVC_OFFSET		0xB08
#define EXYNOSAUTO_SVC_OFFSET		0xF008

/* helpers to access interrupt service register */
#define EXYNOS_SVC_GROUP_SHIFT		3
#define EXYNOS_SVC_GROUP_MASK		0x1f
#define EXYNOS_SVC_NUM_MASK		7
#define EXYNOS_SVC_GROUP(x)		((x >> EXYNOS_SVC_GROUP_SHIFT) & \
						EXYNOS_SVC_GROUP_MASK)

/* Exynos specific external interrupt trigger types */
#define EXYNOS_EINT_LEVEL_LOW		0
#define EXYNOS_EINT_LEVEL_HIGH		1
#define EXYNOS_EINT_EDGE_FALLING	2
#define EXYNOS_EINT_EDGE_RISING		3
#define EXYNOS_EINT_EDGE_BOTH		4
#define EXYNOS_EINT_CON_MASK		0xF
#define EXYNOS_EINT_CON_LEN		4

#define EXYNOS_EINT_MAX_PER_BANK	8
#define EXYNOS_EINT_NR_WKUP_EINT

/*
 * EINT filter configuration register (on alive banks) has
 * the following layout.
 *
 * BitfieldName[PinNum][Bit:Bit]
 * FLT_EN[3][31] FLT_SEL[3][30] FLT_WIDTH[3][29:24]
 * FLT_EN[2][23] FLT_SEL[2][22] FLT_WIDTH[2][21:16]
 * FLT_EN[1][15] FLT_SEL[1][14] FLT_WIDTH[1][13:8]
 * FLT_EN[0][7]  FLT_SEL[0][6]  FLT_WIDTH[0][5:0]
 *
 * FLT_EN	0x0 = Disable, 0x1=Enable
 * FLT_SEL	0x0 = Analog delay filter, 0x1 Digital filter (clock count)
 * FLT_WIDTH	Filtering width. Valid when FLT_SEL is 0x1
 */

#define EXYNOS_FLTCON_EN		BIT(7)
#define EXYNOS_FLTCON_DIGITAL		BIT(6)
#define EXYNOS_FLTCON_ANALOG		(0 << 6)
#define EXYNOS_FLTCON_LEN		8

#define EXYNOS_PIN_BANK_EINTN(pins, reg, id)		\
	{						\
		.type		= &bank_type_off,	\
		.pctl_offset	= reg,			\
		.nr_pins	= pins,			\
		.eint_type	= EINT_TYPE_NONE,	\
		.name		= id			\
	}

#define EXYNOS_PIN_BANK_EINTG(pins, reg, id, offs)	\
	{						\
		.type		= &bank_type_off,	\
		.pctl_offset	= reg,			\
		.nr_pins	= pins,			\
		.eint_type	= EINT_TYPE_GPIO,	\
		.eint_offset	= offs,			\
		.name		= id			\
	}

#define EXYNOS_PIN_BANK_EINTW(pins, reg, id, offs)	\
	{						\
		.type		= &bank_type_alive,	\
		.pctl_offset	= reg,			\
		.nr_pins	= pins,			\
		.eint_type	= EINT_TYPE_WKUP,	\
		.eint_offset	= offs,			\
		.name		= id			\
	}

#define EXYNOS5433_PIN_BANK_EINTG(pins, reg, id, offs)		\
	{							\
		.type		= &exynos5433_bank_type_off,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_GPIO,		\
		.eint_offset	= offs,				\
		.name		= id				\
	}

#define EXYNOS5433_PIN_BANK_EINTW(pins, reg, id, offs)		\
	{							\
		.type		= &exynos5433_bank_type_alive,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_WKUP,		\
		.eint_offset	= offs,				\
		.name		= id				\
	}

#define EXYNOS5433_PIN_BANK_EINTW_EXT(pins, reg, id, offs, pctl_idx) \
	{							\
		.type           = &exynos5433_bank_type_off,	\
		.pctl_offset    = reg,				\
		.nr_pins        = pins,				\
		.eint_type      = EINT_TYPE_WKUP,		\
		.eint_offset    = offs,				\
		.name           = id,				\
		.pctl_res_idx   = pctl_idx,			\
	}							\

#define EXYNOS7870_PIN_BANK_EINTN(pins, reg, id)		\
	{							\
		.type		= &exynos7870_bank_type_alive,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_NONE,		\
		.name		= id				\
	}

#define EXYNOS7870_PIN_BANK_EINTW(pins, reg, id, offs)		\
	{							\
		.type		= &exynos7870_bank_type_alive,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_WKUP,		\
		.eint_offset	= offs,				\
		.name		= id				\
	}

#define EXYNOS850_PIN_BANK_EINTN(pins, reg, id)			\
	{							\
		.type		= &exynos850_bank_type_alive,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_NONE,		\
		.name		= id				\
	}

#define EXYNOS850_PIN_BANK_EINTG(pins, reg, id, offs)		\
	{							\
		.type		= &exynos850_bank_type_off,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_GPIO,		\
		.eint_offset	= offs,				\
		.name		= id				\
	}

#define EXYNOS850_PIN_BANK_EINTW(pins, reg, id, offs)		\
	{							\
		.type		= &exynos850_bank_type_alive,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_WKUP,		\
		.eint_offset	= offs,				\
		.name		= id				\
	}

#define EXYNOS8895_PIN_BANK_EINTG(pins, reg, id, offs)		\
	{							\
		.type		= &exynos8895_bank_type_off,	\
		.pctl_offset	= reg,				\
		.nr_pins	= pins,				\
		.eint_type	= EINT_TYPE_GPIO,		\
		.eint_offset	= offs,				\
		.name		= id				\
	}

#define EXYNOSV920_PIN_BANK_EINTG(pins, reg, id, con_offs, mask_offs, pend_offs)	\
	{							\
		.type			= &exynos850_bank_type_off,	\
		.pctl_offset		= reg,				\
		.nr_pins		= pins,				\
		.eint_type		= EINT_TYPE_GPIO,		\
		.eint_con_offset	= con_offs,			\
		.eint_mask_offset	= mask_offs,			\
		.eint_pend_offset	= pend_offs,			\
		.name			= id				\
	}

#define EXYNOSV920_PIN_BANK_EINTW(pins, reg, id, con_offs, mask_offs, pend_offs)	\
	{							\
		.type			= &exynos850_bank_type_alive,	\
		.pctl_offset		= reg,				\
		.nr_pins		= pins,				\
		.eint_type		= EINT_TYPE_WKUP,		\
		.eint_con_offset	= con_offs,			\
		.eint_mask_offset	= mask_offs,			\
		.eint_pend_offset	= pend_offs,			\
		.name			= id				\
	}

#define GS101_PIN_BANK_EINTG(pins, reg, id, offs, fltcon_offs) \
	{							\
		.type			= &exynos850_bank_type_off,	\
		.pctl_offset		= reg,			\
		.nr_pins		= pins,			\
		.eint_type		= EINT_TYPE_GPIO,	\
		.eint_offset		= offs,			\
		.eint_fltcon_offset	= fltcon_offs,		\
		.name			= id			\
	}

#define GS101_PIN_BANK_EINTW(pins, reg, id, offs, fltcon_offs) \
	{								\
		.type			= &exynos850_bank_type_alive,	\
		.pctl_offset		= reg,				\
		.nr_pins		= pins,				\
		.eint_type		= EINT_TYPE_WKUP,		\
		.eint_offset		= offs,				\
		.eint_fltcon_offset	= fltcon_offs,			\
		.name			= id				\
	}

/**
 * struct exynos_weint_data: irq specific data for all the wakeup interrupts
 * generated by the external wakeup interrupt controller.
 * @irq: interrupt number within the domain.
 * @bank: bank responsible for this interrupt
 */
struct exynos_weint_data {
	unsigned int irq;
	struct samsung_pin_bank *bank;
};

/**
 * struct exynos_muxed_weint_data: irq specific data for muxed wakeup interrupts
 * generated by the external wakeup interrupt controller.
 * @nr_banks: count of banks being part of the mux
 * @banks: array of banks being part of the mux
 */
struct exynos_muxed_weint_data {
	unsigned int nr_banks;
	struct samsung_pin_bank *banks[] __counted_by(nr_banks);
};

int exynos_eint_gpio_init(struct samsung_pinctrl_drv_data *d);
int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d);
void exynosautov920_pinctrl_resume(struct samsung_pin_bank *bank);
void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank);
void exynos_pinctrl_suspend(struct samsung_pin_bank *bank);
void exynos_pinctrl_resume(struct samsung_pin_bank *bank);
void gs101_pinctrl_suspend(struct samsung_pin_bank *bank);
void gs101_pinctrl_resume(struct samsung_pin_bank *bank);
struct samsung_retention_ctrl *
exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
		      const struct samsung_retention_data *data);

#endif /* __PINCTRL_SAMSUNG_EXYNOS_H */