| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * ti_fpc202.c - FPC202 Dual Port Controller driver |
| * |
| * Copyright (C) 2024 Bootlin |
| * |
| */ |
| |
| #include <linux/cleanup.h> |
| #include <linux/err.h> |
| #include <linux/i2c.h> |
| #include <linux/i2c-atr.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/module.h> |
| |
| #define FPC202_NUM_PORTS 2 |
| #define FPC202_ALIASES_PER_PORT 2 |
| |
| /* |
| * GPIO: port mapping |
| * |
| * 0: P0_S0_IN_A |
| * 1: P0_S1_IN_A |
| * 2: P1_S0_IN_A |
| * 3: P1_S1_IN_A |
| * 4: P0_S0_IN_B |
| * ... |
| * 8: P0_S0_IN_C |
| * ... |
| * 12: P0_S0_OUT_A |
| * ... |
| * 16: P0_S0_OUT_B |
| * ... |
| * 19: P1_S1_OUT_B |
| * |
| */ |
| |
| #define FPC202_GPIO_COUNT 20 |
| #define FPC202_GPIO_P0_S0_IN_B 4 |
| #define FPC202_GPIO_P0_S0_OUT_A 12 |
| |
| #define FPC202_REG_IN_A_INT 0x6 |
| #define FPC202_REG_IN_C_IN_B 0x7 |
| #define FPC202_REG_OUT_A_OUT_B 0x8 |
| |
| #define FPC202_REG_OUT_A_OUT_B_VAL 0xa |
| |
| #define FPC202_REG_MOD_DEV(port, dev) (0xb4 + ((port) * 4) + (dev)) |
| #define FPC202_REG_AUX_DEV(port, dev) (0xb6 + ((port) * 4) + (dev)) |
| |
| /* |
| * The FPC202 doesn't support turning off address translation on a single port. |
| * So just set an invalid I2C address as the translation target when no client |
| * address is attached. |
| */ |
| #define FPC202_REG_DEV_INVALID 0 |
| |
| /* Even aliases are assigned to device 0 and odd aliases to device 1 */ |
| #define fpc202_dev_num_from_alias(alias) ((alias) % 2) |
| |
| struct fpc202_priv { |
| struct i2c_client *client; |
| struct i2c_atr *atr; |
| struct gpio_desc *en_gpio; |
| struct gpio_chip gpio; |
| |
| /* Lock REG_MOD/AUX_DEV and addr_caches during attach/detach */ |
| struct mutex reg_dev_lock; |
| |
| /* Cached device addresses for both ports and their devices */ |
| u8 addr_caches[2][2]; |
| |
| /* Keep track of which ports were probed */ |
| DECLARE_BITMAP(probed_ports, FPC202_NUM_PORTS); |
| }; |
| |
| static void fpc202_fill_alias_table(struct i2c_client *client, u16 *aliases, int port_id) |
| { |
| u16 first_alias; |
| int i; |
| |
| /* |
| * There is a predefined list of aliases for each FPC202 I2C |
| * self-address. This allows daisy-chained FPC202 units to |
| * automatically take on different sets of aliases. |
| * Each port of an FPC202 unit is assigned two aliases from this list. |
| */ |
| first_alias = 0x10 + 4 * port_id + 8 * ((u16)client->addr - 2); |
| |
| for (i = 0; i < FPC202_ALIASES_PER_PORT; i++) |
| aliases[i] = first_alias + i; |
| } |
| |
| static int fpc202_gpio_get_dir(int offset) |
| { |
| return offset < FPC202_GPIO_P0_S0_OUT_A ? GPIO_LINE_DIRECTION_IN : GPIO_LINE_DIRECTION_OUT; |
| } |
| |
| static int fpc202_read(struct fpc202_priv *priv, u8 reg) |
| { |
| int val; |
| |
| val = i2c_smbus_read_byte_data(priv->client, reg); |
| return val; |
| } |
| |
| static int fpc202_write(struct fpc202_priv *priv, u8 reg, u8 value) |
| { |
| return i2c_smbus_write_byte_data(priv->client, reg, value); |
| } |
| |
| static void fpc202_set_enable(struct fpc202_priv *priv, int enable) |
| { |
| if (!priv->en_gpio) |
| return; |
| |
| gpiod_set_value(priv->en_gpio, enable); |
| } |
| |
| static int fpc202_gpio_set(struct gpio_chip *chip, unsigned int offset, |
| int value) |
| { |
| struct fpc202_priv *priv = gpiochip_get_data(chip); |
| int ret; |
| u8 val; |
| |
| ret = fpc202_read(priv, FPC202_REG_OUT_A_OUT_B_VAL); |
| if (ret < 0) { |
| dev_err(&priv->client->dev, "Failed to set GPIO %d value! err %d\n", offset, ret); |
| return ret; |
| } |
| |
| val = (u8)ret; |
| |
| if (value) |
| val |= BIT(offset - FPC202_GPIO_P0_S0_OUT_A); |
| else |
| val &= ~BIT(offset - FPC202_GPIO_P0_S0_OUT_A); |
| |
| return fpc202_write(priv, FPC202_REG_OUT_A_OUT_B_VAL, val); |
| } |
| |
| static int fpc202_gpio_get(struct gpio_chip *chip, unsigned int offset) |
| { |
| struct fpc202_priv *priv = gpiochip_get_data(chip); |
| u8 reg, bit; |
| int ret; |
| |
| if (offset < FPC202_GPIO_P0_S0_IN_B) { |
| reg = FPC202_REG_IN_A_INT; |
| bit = BIT(4 + offset); |
| } else if (offset < FPC202_GPIO_P0_S0_OUT_A) { |
| reg = FPC202_REG_IN_C_IN_B; |
| bit = BIT(offset - FPC202_GPIO_P0_S0_IN_B); |
| } else { |
| reg = FPC202_REG_OUT_A_OUT_B_VAL; |
| bit = BIT(offset - FPC202_GPIO_P0_S0_OUT_A); |
| } |
| |
| ret = fpc202_read(priv, reg); |
| if (ret < 0) |
| return ret; |
| |
| return !!(((u8)ret) & bit); |
| } |
| |
| static int fpc202_gpio_direction_input(struct gpio_chip *chip, unsigned int offset) |
| { |
| if (fpc202_gpio_get_dir(offset) == GPIO_LINE_DIRECTION_OUT) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static int fpc202_gpio_direction_output(struct gpio_chip *chip, unsigned int offset, |
| int value) |
| { |
| struct fpc202_priv *priv = gpiochip_get_data(chip); |
| int ret; |
| u8 val; |
| |
| if (fpc202_gpio_get_dir(offset) == GPIO_LINE_DIRECTION_IN) |
| return -EINVAL; |
| |
| fpc202_gpio_set(chip, offset, value); |
| |
| ret = fpc202_read(priv, FPC202_REG_OUT_A_OUT_B); |
| if (ret < 0) |
| return ret; |
| |
| val = (u8)ret | BIT(offset - FPC202_GPIO_P0_S0_OUT_A); |
| |
| return fpc202_write(priv, FPC202_REG_OUT_A_OUT_B, val); |
| } |
| |
| /* |
| * Set the translation table entry associated with a port and device number. |
| * |
| * Each downstream port of the FPC202 has two fixed aliases corresponding to |
| * device numbers 0 and 1. If one of these aliases is found in an incoming I2C |
| * transfer, it will be translated to the address given by the corresponding |
| * translation table entry. |
| */ |
| static int fpc202_write_dev_addr(struct fpc202_priv *priv, u32 port_id, int dev_num, u16 addr) |
| { |
| int ret, reg_mod, reg_aux; |
| u8 val; |
| |
| guard(mutex)(&priv->reg_dev_lock); |
| |
| reg_mod = FPC202_REG_MOD_DEV(port_id, dev_num); |
| reg_aux = FPC202_REG_AUX_DEV(port_id, dev_num); |
| val = addr & 0x7f; |
| |
| ret = fpc202_write(priv, reg_mod, val); |
| if (ret) |
| return ret; |
| |
| /* |
| * The FPC202 datasheet is unclear about the role of the AUX registers. |
| * Empirically, writing to them as well seems to be necessary for |
| * address translation to function properly. |
| */ |
| ret = fpc202_write(priv, reg_aux, val); |
| |
| priv->addr_caches[port_id][dev_num] = val; |
| |
| return ret; |
| } |
| |
| static int fpc202_attach_addr(struct i2c_atr *atr, u32 chan_id, |
| u16 addr, u16 alias) |
| { |
| struct fpc202_priv *priv = i2c_atr_get_driver_data(atr); |
| |
| dev_dbg(&priv->client->dev, "attaching address 0x%02x to alias 0x%02x\n", addr, alias); |
| |
| return fpc202_write_dev_addr(priv, chan_id, fpc202_dev_num_from_alias(alias), addr); |
| } |
| |
| static void fpc202_detach_addr(struct i2c_atr *atr, u32 chan_id, |
| u16 addr) |
| { |
| struct fpc202_priv *priv = i2c_atr_get_driver_data(atr); |
| int dev_num, reg_mod, val; |
| |
| for (dev_num = 0; dev_num < 2; dev_num++) { |
| reg_mod = FPC202_REG_MOD_DEV(chan_id, dev_num); |
| |
| mutex_lock(&priv->reg_dev_lock); |
| |
| val = priv->addr_caches[chan_id][dev_num]; |
| |
| mutex_unlock(&priv->reg_dev_lock); |
| |
| if (val < 0) { |
| dev_err(&priv->client->dev, "failed to read register 0x%x while detaching address 0x%02x\n", |
| reg_mod, addr); |
| return; |
| } |
| |
| if (val == (addr & 0x7f)) { |
| fpc202_write_dev_addr(priv, chan_id, dev_num, FPC202_REG_DEV_INVALID); |
| return; |
| } |
| } |
| } |
| |
| static const struct i2c_atr_ops fpc202_atr_ops = { |
| .attach_addr = fpc202_attach_addr, |
| .detach_addr = fpc202_detach_addr, |
| }; |
| |
| static int fpc202_probe_port(struct fpc202_priv *priv, struct device_node *i2c_handle, int port_id) |
| { |
| u16 aliases[FPC202_ALIASES_PER_PORT] = { }; |
| struct device *dev = &priv->client->dev; |
| struct i2c_atr_adap_desc desc = { }; |
| int ret = 0; |
| |
| desc.chan_id = port_id; |
| desc.parent = dev; |
| desc.bus_handle = of_fwnode_handle(i2c_handle); |
| desc.num_aliases = FPC202_ALIASES_PER_PORT; |
| |
| fpc202_fill_alias_table(priv->client, aliases, port_id); |
| desc.aliases = aliases; |
| |
| ret = i2c_atr_add_adapter(priv->atr, &desc); |
| if (ret) |
| return ret; |
| |
| set_bit(port_id, priv->probed_ports); |
| |
| ret = fpc202_write_dev_addr(priv, port_id, 0, FPC202_REG_DEV_INVALID); |
| if (ret) |
| return ret; |
| |
| return fpc202_write_dev_addr(priv, port_id, 1, FPC202_REG_DEV_INVALID); |
| } |
| |
| static void fpc202_remove_port(struct fpc202_priv *priv, int port_id) |
| { |
| i2c_atr_del_adapter(priv->atr, port_id); |
| clear_bit(port_id, priv->probed_ports); |
| } |
| |
| static int fpc202_probe(struct i2c_client *client) |
| { |
| struct device *dev = &client->dev; |
| struct device_node *i2c_handle; |
| struct fpc202_priv *priv; |
| int ret, port_id; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| mutex_init(&priv->reg_dev_lock); |
| |
| priv->client = client; |
| i2c_set_clientdata(client, priv); |
| |
| priv->en_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_HIGH); |
| if (IS_ERR(priv->en_gpio)) { |
| ret = PTR_ERR(priv->en_gpio); |
| dev_err(dev, "failed to fetch enable GPIO! err %d\n", ret); |
| goto destroy_mutex; |
| } |
| |
| priv->gpio.label = "gpio-fpc202"; |
| priv->gpio.base = -1; |
| priv->gpio.direction_input = fpc202_gpio_direction_input; |
| priv->gpio.direction_output = fpc202_gpio_direction_output; |
| priv->gpio.set = fpc202_gpio_set; |
| priv->gpio.get = fpc202_gpio_get; |
| priv->gpio.ngpio = FPC202_GPIO_COUNT; |
| priv->gpio.parent = dev; |
| priv->gpio.owner = THIS_MODULE; |
| |
| ret = gpiochip_add_data(&priv->gpio, priv); |
| if (ret) { |
| priv->gpio.parent = NULL; |
| dev_err(dev, "failed to add gpiochip err %d\n", ret); |
| goto disable_gpio; |
| } |
| |
| priv->atr = i2c_atr_new(client->adapter, dev, &fpc202_atr_ops, 2, 0); |
| if (IS_ERR(priv->atr)) { |
| ret = PTR_ERR(priv->atr); |
| dev_err(dev, "failed to create i2c atr err %d\n", ret); |
| goto disable_gpio; |
| } |
| |
| i2c_atr_set_driver_data(priv->atr, priv); |
| |
| bitmap_zero(priv->probed_ports, FPC202_NUM_PORTS); |
| |
| for_each_child_of_node(dev->of_node, i2c_handle) { |
| ret = of_property_read_u32(i2c_handle, "reg", &port_id); |
| if (ret) { |
| if (ret == -EINVAL) |
| continue; |
| |
| dev_err(dev, "failed to read 'reg' property of child node, err %d\n", ret); |
| goto unregister_chans; |
| } |
| |
| if (port_id > FPC202_NUM_PORTS) { |
| dev_err(dev, "port ID %d is out of range!\n", port_id); |
| ret = -EINVAL; |
| goto unregister_chans; |
| } |
| |
| ret = fpc202_probe_port(priv, i2c_handle, port_id); |
| if (ret) { |
| dev_err(dev, "Failed to probe port %d, err %d\n", port_id, ret); |
| goto unregister_chans; |
| } |
| } |
| |
| goto out; |
| |
| unregister_chans: |
| for_each_set_bit(port_id, priv->probed_ports, FPC202_NUM_PORTS) |
| fpc202_remove_port(priv, port_id); |
| |
| i2c_atr_delete(priv->atr); |
| disable_gpio: |
| fpc202_set_enable(priv, 0); |
| gpiochip_remove(&priv->gpio); |
| destroy_mutex: |
| mutex_destroy(&priv->reg_dev_lock); |
| out: |
| return ret; |
| } |
| |
| static void fpc202_remove(struct i2c_client *client) |
| { |
| struct fpc202_priv *priv = i2c_get_clientdata(client); |
| int port_id; |
| |
| for_each_set_bit(port_id, priv->probed_ports, FPC202_NUM_PORTS) |
| fpc202_remove_port(priv, port_id); |
| |
| mutex_destroy(&priv->reg_dev_lock); |
| |
| i2c_atr_delete(priv->atr); |
| |
| fpc202_set_enable(priv, 0); |
| gpiochip_remove(&priv->gpio); |
| } |
| |
| static const struct of_device_id fpc202_of_match[] = { |
| { .compatible = "ti,fpc202" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, fpc202_of_match); |
| |
| static struct i2c_driver fpc202_driver = { |
| .driver = { |
| .name = "fpc202", |
| .of_match_table = fpc202_of_match, |
| }, |
| .probe = fpc202_probe, |
| .remove = fpc202_remove, |
| }; |
| |
| module_i2c_driver(fpc202_driver); |
| |
| MODULE_AUTHOR("Romain Gantois <romain.gantois@bootlin.com>"); |
| MODULE_DESCRIPTION("TI FPC202 Dual Port Controller driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_IMPORT_NS("I2C_ATR"); |