blob: f57a8f841498415fa33c7075df0ab0df3f087c8d [file] [log] [blame]
/*
* Device Tree file for Marvell Armada 370 Reference Design board
* (RD-88F6710-A1)
*
* Copied from arch/arm/boot/dts/armada-370-db.dts
*
* Copyright (C) 2013 Florian Fainelli <florian@openwrt.org>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*
* Note: this Device Tree assumes that the bootloader has remapped the
* internal registers to 0xf1000000 (instead of the default
* 0xd0000000). The 0xf1000000 is the default used by the recent,
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
* boards were delivered with an older version of the bootloader that
* left internal registers mapped at 0xd0000000. If you are in this
* situation, you should either update your bootloader (preferred
* solution) or the below Device Tree should be adjusted.
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "armada-370.dtsi"
/ {
model = "Marvell Armada 370 Reference Design";
compatible = "marvell,a370-rd", "marvell,armada370", "marvell,armada-370-xp";
chosen {
bootargs = "console=ttyS0,115200 earlyprintk";
};
memory {
device_type = "memory";
reg = <0x00000000 0x20000000>; /* 512 MB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
pcie-controller {
status = "okay";
/* Internal mini-PCIe connector */
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
/* Internal mini-PCIe connector */
pcie@2,0 {
/* Port 1, Lane 0 */
status = "okay";
};
};
internal-regs {
pinctrl {
fan_pins: fan-pins {
marvell,pins = "mpp8";
marvell,function = "gpio";
};
led_pins: led-pins {
marvell,pins = "mpp32";
marvell,function = "gpio";
};
};
serial@12000 {
status = "okay";
};
sata@a0000 {
nr-ports = <2>;
status = "okay";
};
mdio {
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
};
ethernet@70000 {
status = "okay";
phy = <&phy0>;
phy-mode = "sgmii";
};
ethernet@74000 {
pinctrl-0 = <&ge1_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
phy = <&phy1>;
phy-mode = "rgmii-id";
};
mvsdio@d4000 {
pinctrl-0 = <&sdio_pins1>;
pinctrl-names = "default";
status = "okay";
/* No CD or WP GPIOs */
broken-cd;
};
usb@50000 {
status = "okay";
};
usb@51000 {
status = "okay";
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "Software Button";
linux,code = <KEY_POWER>;
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
};
gpio-fan {
compatible = "gpio-fan";
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
gpio-fan,speed-map = <0 0 3000 1>;
pinctrl-0 = <&fan_pins>;
pinctrl-names = "default";
};
gpio_leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
sw_led {
label = "370rd:green:sw";
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
};
nand@d0000 {
status = "okay";
num-cs = <1>;
marvell,nand-keep-config;
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
partition@0 {
label = "U-Boot";
reg = <0 0x800000>;
};
partition@800000 {
label = "Linux";
reg = <0x800000 0x800000>;
};
partition@1000000 {
label = "Filesystem";
reg = <0x1000000 0x3f000000>;
};
};
};
};
};