| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/device.h> | |
| #include <linux/err.h> | |
| #include <linux/debugfs.h> | |
| #include <linux/seq_file.h> | |
| #include <linux/gpio.h> | |
| #include <linux/of_gpio.h> | |
| #include <linux/idr.h> | |
| #include <linux/slab.h> | |
| #define CREATE_TRACE_POINTS | |
| #include <trace/events/gpio.h> | |
| /* Optional implementation infrastructure for GPIO interfaces. | |
| * | |
| * Platforms may want to use this if they tend to use very many GPIOs | |
| * that aren't part of a System-On-Chip core; or across I2C/SPI/etc. | |
| * | |
| * When kernel footprint or instruction count is an issue, simpler | |
| * implementations may be preferred. The GPIO programming interface | |
| * allows for inlining speed-critical get/set operations for common | |
| * cases, so that access to SOC-integrated GPIOs can sometimes cost | |
| * only an instruction or two per bit. | |
| */ | |
| /* When debugging, extend minimal trust to callers and platform code. | |
| * Also emit diagnostic messages that may help initial bringup, when | |
| * board setup or driver bugs are most common. | |
| * | |
| * Otherwise, minimize overhead in what may be bitbanging codepaths. | |
| */ | |
| #ifdef DEBUG | |
| #define extra_checks 1 | |
| #else | |
| #define extra_checks 0 | |
| #endif | |
| /* gpio_lock prevents conflicts during gpio_desc[] table updates. | |
| * While any GPIO is requested, its gpio_chip is not removable; | |
| * each GPIO's "requested" flag serves as a lock and refcount. | |
| */ | |
| static DEFINE_SPINLOCK(gpio_lock); | |
| struct gpio_desc { | |
| struct gpio_chip *chip; | |
| unsigned long flags; | |
| /* flag symbols are bit numbers */ | |
| #define FLAG_REQUESTED 0 | |
| #define FLAG_IS_OUT 1 | |
| #define FLAG_RESERVED 2 | |
| #define FLAG_EXPORT 3 /* protected by sysfs_lock */ | |
| #define FLAG_SYSFS 4 /* exported via /sys/class/gpio/control */ | |
| #define FLAG_TRIG_FALL 5 /* trigger on falling edge */ | |
| #define FLAG_TRIG_RISE 6 /* trigger on rising edge */ | |
| #define FLAG_ACTIVE_LOW 7 /* sysfs value has active low */ | |
| #define ID_SHIFT 16 /* add new flags before this one */ | |
| #define GPIO_FLAGS_MASK ((1 << ID_SHIFT) - 1) | |
| #define GPIO_TRIGGER_MASK (BIT(FLAG_TRIG_FALL) | BIT(FLAG_TRIG_RISE)) | |
| #ifdef CONFIG_DEBUG_FS | |
| const char *label; | |
| #endif | |
| }; | |
| static struct gpio_desc gpio_desc[ARCH_NR_GPIOS]; | |
| #ifdef CONFIG_GPIO_SYSFS | |
| static DEFINE_IDR(dirent_idr); | |
| #endif | |
| static inline void desc_set_label(struct gpio_desc *d, const char *label) | |
| { | |
| #ifdef CONFIG_DEBUG_FS | |
| d->label = label; | |
| #endif | |
| } | |
| /* Warn when drivers omit gpio_request() calls -- legal but ill-advised | |
| * when setting direction, and otherwise illegal. Until board setup code | |
| * and drivers use explicit requests everywhere (which won't happen when | |
| * those calls have no teeth) we can't avoid autorequesting. This nag | |
| * message should motivate switching to explicit requests... so should | |
| * the weaker cleanup after faults, compared to gpio_request(). | |
| * | |
| * NOTE: the autorequest mechanism is going away; at this point it's | |
| * only "legal" in the sense that (old) code using it won't break yet, | |
| * but instead only triggers a WARN() stack dump. | |
| */ | |
| static int gpio_ensure_requested(struct gpio_desc *desc, unsigned offset) | |
| { | |
| const struct gpio_chip *chip = desc->chip; | |
| const int gpio = chip->base + offset; | |
| if (WARN(test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0, | |
| "autorequest GPIO-%d\n", gpio)) { | |
| if (!try_module_get(chip->owner)) { | |
| pr_err("GPIO-%d: module can't be gotten \n", gpio); | |
| clear_bit(FLAG_REQUESTED, &desc->flags); | |
| /* lose */ | |
| return -EIO; | |
| } | |
| desc_set_label(desc, "[auto]"); | |
| /* caller must chip->request() w/o spinlock */ | |
| if (chip->request) | |
| return 1; | |
| } | |
| return 0; | |
| } | |
| /* caller holds gpio_lock *OR* gpio is marked as requested */ | |
| static inline struct gpio_chip *gpio_to_chip(unsigned gpio) | |
| { | |
| return gpio_desc[gpio].chip; | |
| } | |
| /* dynamic allocation of GPIOs, e.g. on a hotplugged device */ | |
| static int gpiochip_find_base(int ngpio) | |
| { | |
| int i; | |
| int spare = 0; | |
| int base = -ENOSPC; | |
| for (i = ARCH_NR_GPIOS - 1; i >= 0 ; i--) { | |
| struct gpio_desc *desc = &gpio_desc[i]; | |
| struct gpio_chip *chip = desc->chip; | |
| if (!chip && !test_bit(FLAG_RESERVED, &desc->flags)) { | |
| spare++; | |
| if (spare == ngpio) { | |
| base = i; | |
| break; | |
| } | |
| } else { | |
| spare = 0; | |
| if (chip) | |
| i -= chip->ngpio - 1; | |
| } | |
| } | |
| if (gpio_is_valid(base)) | |
| pr_debug("%s: found new base at %d\n", __func__, base); | |
| return base; | |
| } | |
| /** | |
| * gpiochip_reserve() - reserve range of gpios to use with platform code only | |
| * @start: starting gpio number | |
| * @ngpio: number of gpios to reserve | |
| * Context: platform init, potentially before irqs or kmalloc will work | |
| * | |
| * Returns a negative errno if any gpio within the range is already reserved | |
| * or registered, else returns zero as a success code. Use this function | |
| * to mark a range of gpios as unavailable for dynamic gpio number allocation, | |
| * for example because its driver support is not yet loaded. | |
| */ | |
| int __init gpiochip_reserve(int start, int ngpio) | |
| { | |
| int ret = 0; | |
| unsigned long flags; | |
| int i; | |
| if (!gpio_is_valid(start) || !gpio_is_valid(start + ngpio - 1)) | |
| return -EINVAL; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| for (i = start; i < start + ngpio; i++) { | |
| struct gpio_desc *desc = &gpio_desc[i]; | |
| if (desc->chip || test_bit(FLAG_RESERVED, &desc->flags)) { | |
| ret = -EBUSY; | |
| goto err; | |
| } | |
| set_bit(FLAG_RESERVED, &desc->flags); | |
| } | |
| pr_debug("%s: reserved gpios from %d to %d\n", | |
| __func__, start, start + ngpio - 1); | |
| err: | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| return ret; | |
| } | |
| #ifdef CONFIG_GPIO_SYSFS | |
| /* lock protects against unexport_gpio() being called while | |
| * sysfs files are active. | |
| */ | |
| static DEFINE_MUTEX(sysfs_lock); | |
| /* | |
| * /sys/class/gpio/gpioN... only for GPIOs that are exported | |
| * /direction | |
| * * MAY BE OMITTED if kernel won't allow direction changes | |
| * * is read/write as "in" or "out" | |
| * * may also be written as "high" or "low", initializing | |
| * output value as specified ("out" implies "low") | |
| * /value | |
| * * always readable, subject to hardware behavior | |
| * * may be writable, as zero/nonzero | |
| * /edge | |
| * * configures behavior of poll(2) on /value | |
| * * available only if pin can generate IRQs on input | |
| * * is read/write as "none", "falling", "rising", or "both" | |
| * /active_low | |
| * * configures polarity of /value | |
| * * is read/write as zero/nonzero | |
| * * also affects existing and subsequent "falling" and "rising" | |
| * /edge configuration | |
| */ | |
| static ssize_t gpio_direction_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_desc *desc = dev_get_drvdata(dev); | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) | |
| status = -EIO; | |
| else | |
| status = sprintf(buf, "%s\n", | |
| test_bit(FLAG_IS_OUT, &desc->flags) | |
| ? "out" : "in"); | |
| mutex_unlock(&sysfs_lock); | |
| return status; | |
| } | |
| static ssize_t gpio_direction_store(struct device *dev, | |
| struct device_attribute *attr, const char *buf, size_t size) | |
| { | |
| const struct gpio_desc *desc = dev_get_drvdata(dev); | |
| unsigned gpio = desc - gpio_desc; | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) | |
| status = -EIO; | |
| else if (sysfs_streq(buf, "high")) | |
| status = gpio_direction_output(gpio, 1); | |
| else if (sysfs_streq(buf, "out") || sysfs_streq(buf, "low")) | |
| status = gpio_direction_output(gpio, 0); | |
| else if (sysfs_streq(buf, "in")) | |
| status = gpio_direction_input(gpio); | |
| else | |
| status = -EINVAL; | |
| mutex_unlock(&sysfs_lock); | |
| return status ? : size; | |
| } | |
| static /* const */ DEVICE_ATTR(direction, 0644, | |
| gpio_direction_show, gpio_direction_store); | |
| static ssize_t gpio_value_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_desc *desc = dev_get_drvdata(dev); | |
| unsigned gpio = desc - gpio_desc; | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) { | |
| status = -EIO; | |
| } else { | |
| int value; | |
| value = !!gpio_get_value_cansleep(gpio); | |
| if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | |
| value = !value; | |
| status = sprintf(buf, "%d\n", value); | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| return status; | |
| } | |
| static ssize_t gpio_value_store(struct device *dev, | |
| struct device_attribute *attr, const char *buf, size_t size) | |
| { | |
| const struct gpio_desc *desc = dev_get_drvdata(dev); | |
| unsigned gpio = desc - gpio_desc; | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) | |
| status = -EIO; | |
| else if (!test_bit(FLAG_IS_OUT, &desc->flags)) | |
| status = -EPERM; | |
| else { | |
| long value; | |
| status = strict_strtol(buf, 0, &value); | |
| if (status == 0) { | |
| if (test_bit(FLAG_ACTIVE_LOW, &desc->flags)) | |
| value = !value; | |
| gpio_set_value_cansleep(gpio, value != 0); | |
| status = size; | |
| } | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| return status; | |
| } | |
| static const DEVICE_ATTR(value, 0644, | |
| gpio_value_show, gpio_value_store); | |
| static irqreturn_t gpio_sysfs_irq(int irq, void *priv) | |
| { | |
| struct sysfs_dirent *value_sd = priv; | |
| sysfs_notify_dirent(value_sd); | |
| return IRQ_HANDLED; | |
| } | |
| static int gpio_setup_irq(struct gpio_desc *desc, struct device *dev, | |
| unsigned long gpio_flags) | |
| { | |
| struct sysfs_dirent *value_sd; | |
| unsigned long irq_flags; | |
| int ret, irq, id; | |
| if ((desc->flags & GPIO_TRIGGER_MASK) == gpio_flags) | |
| return 0; | |
| irq = gpio_to_irq(desc - gpio_desc); | |
| if (irq < 0) | |
| return -EIO; | |
| id = desc->flags >> ID_SHIFT; | |
| value_sd = idr_find(&dirent_idr, id); | |
| if (value_sd) | |
| free_irq(irq, value_sd); | |
| desc->flags &= ~GPIO_TRIGGER_MASK; | |
| if (!gpio_flags) { | |
| ret = 0; | |
| goto free_id; | |
| } | |
| irq_flags = IRQF_SHARED; | |
| if (test_bit(FLAG_TRIG_FALL, &gpio_flags)) | |
| irq_flags |= test_bit(FLAG_ACTIVE_LOW, &desc->flags) ? | |
| IRQF_TRIGGER_RISING : IRQF_TRIGGER_FALLING; | |
| if (test_bit(FLAG_TRIG_RISE, &gpio_flags)) | |
| irq_flags |= test_bit(FLAG_ACTIVE_LOW, &desc->flags) ? | |
| IRQF_TRIGGER_FALLING : IRQF_TRIGGER_RISING; | |
| if (!value_sd) { | |
| value_sd = sysfs_get_dirent(dev->kobj.sd, NULL, "value"); | |
| if (!value_sd) { | |
| ret = -ENODEV; | |
| goto err_out; | |
| } | |
| do { | |
| ret = -ENOMEM; | |
| if (idr_pre_get(&dirent_idr, GFP_KERNEL)) | |
| ret = idr_get_new_above(&dirent_idr, value_sd, | |
| 1, &id); | |
| } while (ret == -EAGAIN); | |
| if (ret) | |
| goto free_sd; | |
| desc->flags &= GPIO_FLAGS_MASK; | |
| desc->flags |= (unsigned long)id << ID_SHIFT; | |
| if (desc->flags >> ID_SHIFT != id) { | |
| ret = -ERANGE; | |
| goto free_id; | |
| } | |
| } | |
| ret = request_any_context_irq(irq, gpio_sysfs_irq, irq_flags, | |
| "gpiolib", value_sd); | |
| if (ret < 0) | |
| goto free_id; | |
| desc->flags |= gpio_flags; | |
| return 0; | |
| free_id: | |
| idr_remove(&dirent_idr, id); | |
| desc->flags &= GPIO_FLAGS_MASK; | |
| free_sd: | |
| if (value_sd) | |
| sysfs_put(value_sd); | |
| err_out: | |
| return ret; | |
| } | |
| static const struct { | |
| const char *name; | |
| unsigned long flags; | |
| } trigger_types[] = { | |
| { "none", 0 }, | |
| { "falling", BIT(FLAG_TRIG_FALL) }, | |
| { "rising", BIT(FLAG_TRIG_RISE) }, | |
| { "both", BIT(FLAG_TRIG_FALL) | BIT(FLAG_TRIG_RISE) }, | |
| }; | |
| static ssize_t gpio_edge_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_desc *desc = dev_get_drvdata(dev); | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) | |
| status = -EIO; | |
| else { | |
| int i; | |
| status = 0; | |
| for (i = 0; i < ARRAY_SIZE(trigger_types); i++) | |
| if ((desc->flags & GPIO_TRIGGER_MASK) | |
| == trigger_types[i].flags) { | |
| status = sprintf(buf, "%s\n", | |
| trigger_types[i].name); | |
| break; | |
| } | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| return status; | |
| } | |
| static ssize_t gpio_edge_store(struct device *dev, | |
| struct device_attribute *attr, const char *buf, size_t size) | |
| { | |
| struct gpio_desc *desc = dev_get_drvdata(dev); | |
| ssize_t status; | |
| int i; | |
| for (i = 0; i < ARRAY_SIZE(trigger_types); i++) | |
| if (sysfs_streq(trigger_types[i].name, buf)) | |
| goto found; | |
| return -EINVAL; | |
| found: | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) | |
| status = -EIO; | |
| else { | |
| status = gpio_setup_irq(desc, dev, trigger_types[i].flags); | |
| if (!status) | |
| status = size; | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| return status; | |
| } | |
| static DEVICE_ATTR(edge, 0644, gpio_edge_show, gpio_edge_store); | |
| static int sysfs_set_active_low(struct gpio_desc *desc, struct device *dev, | |
| int value) | |
| { | |
| int status = 0; | |
| if (!!test_bit(FLAG_ACTIVE_LOW, &desc->flags) == !!value) | |
| return 0; | |
| if (value) | |
| set_bit(FLAG_ACTIVE_LOW, &desc->flags); | |
| else | |
| clear_bit(FLAG_ACTIVE_LOW, &desc->flags); | |
| /* reconfigure poll(2) support if enabled on one edge only */ | |
| if (dev != NULL && (!!test_bit(FLAG_TRIG_RISE, &desc->flags) ^ | |
| !!test_bit(FLAG_TRIG_FALL, &desc->flags))) { | |
| unsigned long trigger_flags = desc->flags & GPIO_TRIGGER_MASK; | |
| gpio_setup_irq(desc, dev, 0); | |
| status = gpio_setup_irq(desc, dev, trigger_flags); | |
| } | |
| return status; | |
| } | |
| static ssize_t gpio_active_low_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_desc *desc = dev_get_drvdata(dev); | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) | |
| status = -EIO; | |
| else | |
| status = sprintf(buf, "%d\n", | |
| !!test_bit(FLAG_ACTIVE_LOW, &desc->flags)); | |
| mutex_unlock(&sysfs_lock); | |
| return status; | |
| } | |
| static ssize_t gpio_active_low_store(struct device *dev, | |
| struct device_attribute *attr, const char *buf, size_t size) | |
| { | |
| struct gpio_desc *desc = dev_get_drvdata(dev); | |
| ssize_t status; | |
| mutex_lock(&sysfs_lock); | |
| if (!test_bit(FLAG_EXPORT, &desc->flags)) { | |
| status = -EIO; | |
| } else { | |
| long value; | |
| status = strict_strtol(buf, 0, &value); | |
| if (status == 0) | |
| status = sysfs_set_active_low(desc, dev, value != 0); | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| return status ? : size; | |
| } | |
| static const DEVICE_ATTR(active_low, 0644, | |
| gpio_active_low_show, gpio_active_low_store); | |
| static const struct attribute *gpio_attrs[] = { | |
| &dev_attr_value.attr, | |
| &dev_attr_active_low.attr, | |
| NULL, | |
| }; | |
| static const struct attribute_group gpio_attr_group = { | |
| .attrs = (struct attribute **) gpio_attrs, | |
| }; | |
| /* | |
| * /sys/class/gpio/gpiochipN/ | |
| * /base ... matching gpio_chip.base (N) | |
| * /label ... matching gpio_chip.label | |
| * /ngpio ... matching gpio_chip.ngpio | |
| */ | |
| static ssize_t chip_base_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_chip *chip = dev_get_drvdata(dev); | |
| return sprintf(buf, "%d\n", chip->base); | |
| } | |
| static DEVICE_ATTR(base, 0444, chip_base_show, NULL); | |
| static ssize_t chip_label_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_chip *chip = dev_get_drvdata(dev); | |
| return sprintf(buf, "%s\n", chip->label ? : ""); | |
| } | |
| static DEVICE_ATTR(label, 0444, chip_label_show, NULL); | |
| static ssize_t chip_ngpio_show(struct device *dev, | |
| struct device_attribute *attr, char *buf) | |
| { | |
| const struct gpio_chip *chip = dev_get_drvdata(dev); | |
| return sprintf(buf, "%u\n", chip->ngpio); | |
| } | |
| static DEVICE_ATTR(ngpio, 0444, chip_ngpio_show, NULL); | |
| static const struct attribute *gpiochip_attrs[] = { | |
| &dev_attr_base.attr, | |
| &dev_attr_label.attr, | |
| &dev_attr_ngpio.attr, | |
| NULL, | |
| }; | |
| static const struct attribute_group gpiochip_attr_group = { | |
| .attrs = (struct attribute **) gpiochip_attrs, | |
| }; | |
| /* | |
| * /sys/class/gpio/export ... write-only | |
| * integer N ... number of GPIO to export (full access) | |
| * /sys/class/gpio/unexport ... write-only | |
| * integer N ... number of GPIO to unexport | |
| */ | |
| static ssize_t export_store(struct class *class, | |
| struct class_attribute *attr, | |
| const char *buf, size_t len) | |
| { | |
| long gpio; | |
| int status; | |
| status = strict_strtol(buf, 0, &gpio); | |
| if (status < 0) | |
| goto done; | |
| /* No extra locking here; FLAG_SYSFS just signifies that the | |
| * request and export were done by on behalf of userspace, so | |
| * they may be undone on its behalf too. | |
| */ | |
| status = gpio_request(gpio, "sysfs"); | |
| if (status < 0) | |
| goto done; | |
| status = gpio_export(gpio, true); | |
| if (status < 0) | |
| gpio_free(gpio); | |
| else | |
| set_bit(FLAG_SYSFS, &gpio_desc[gpio].flags); | |
| done: | |
| if (status) | |
| pr_debug("%s: status %d\n", __func__, status); | |
| return status ? : len; | |
| } | |
| static ssize_t unexport_store(struct class *class, | |
| struct class_attribute *attr, | |
| const char *buf, size_t len) | |
| { | |
| long gpio; | |
| int status; | |
| status = strict_strtol(buf, 0, &gpio); | |
| if (status < 0) | |
| goto done; | |
| status = -EINVAL; | |
| /* reject bogus commands (gpio_unexport ignores them) */ | |
| if (!gpio_is_valid(gpio)) | |
| goto done; | |
| /* No extra locking here; FLAG_SYSFS just signifies that the | |
| * request and export were done by on behalf of userspace, so | |
| * they may be undone on its behalf too. | |
| */ | |
| if (test_and_clear_bit(FLAG_SYSFS, &gpio_desc[gpio].flags)) { | |
| status = 0; | |
| gpio_free(gpio); | |
| } | |
| done: | |
| if (status) | |
| pr_debug("%s: status %d\n", __func__, status); | |
| return status ? : len; | |
| } | |
| static struct class_attribute gpio_class_attrs[] = { | |
| __ATTR(export, 0200, NULL, export_store), | |
| __ATTR(unexport, 0200, NULL, unexport_store), | |
| __ATTR_NULL, | |
| }; | |
| static struct class gpio_class = { | |
| .name = "gpio", | |
| .owner = THIS_MODULE, | |
| .class_attrs = gpio_class_attrs, | |
| }; | |
| /** | |
| * gpio_export - export a GPIO through sysfs | |
| * @gpio: gpio to make available, already requested | |
| * @direction_may_change: true if userspace may change gpio direction | |
| * Context: arch_initcall or later | |
| * | |
| * When drivers want to make a GPIO accessible to userspace after they | |
| * have requested it -- perhaps while debugging, or as part of their | |
| * public interface -- they may use this routine. If the GPIO can | |
| * change direction (some can't) and the caller allows it, userspace | |
| * will see "direction" sysfs attribute which may be used to change | |
| * the gpio's direction. A "value" attribute will always be provided. | |
| * | |
| * Returns zero on success, else an error. | |
| */ | |
| int gpio_export(unsigned gpio, bool direction_may_change) | |
| { | |
| unsigned long flags; | |
| struct gpio_desc *desc; | |
| int status = -EINVAL; | |
| const char *ioname = NULL; | |
| /* can't export until sysfs is available ... */ | |
| if (!gpio_class.p) { | |
| pr_debug("%s: called too early!\n", __func__); | |
| return -ENOENT; | |
| } | |
| if (!gpio_is_valid(gpio)) | |
| goto done; | |
| mutex_lock(&sysfs_lock); | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| desc = &gpio_desc[gpio]; | |
| if (test_bit(FLAG_REQUESTED, &desc->flags) | |
| && !test_bit(FLAG_EXPORT, &desc->flags)) { | |
| status = 0; | |
| if (!desc->chip->direction_input | |
| || !desc->chip->direction_output) | |
| direction_may_change = false; | |
| } | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| if (desc->chip->names && desc->chip->names[gpio - desc->chip->base]) | |
| ioname = desc->chip->names[gpio - desc->chip->base]; | |
| if (status == 0) { | |
| struct device *dev; | |
| dev = device_create(&gpio_class, desc->chip->dev, MKDEV(0, 0), | |
| desc, ioname ? ioname : "gpio%u", gpio); | |
| if (!IS_ERR(dev)) { | |
| status = sysfs_create_group(&dev->kobj, | |
| &gpio_attr_group); | |
| if (!status && direction_may_change) | |
| status = device_create_file(dev, | |
| &dev_attr_direction); | |
| if (!status && gpio_to_irq(gpio) >= 0 | |
| && (direction_may_change | |
| || !test_bit(FLAG_IS_OUT, | |
| &desc->flags))) | |
| status = device_create_file(dev, | |
| &dev_attr_edge); | |
| if (status != 0) | |
| device_unregister(dev); | |
| } else | |
| status = PTR_ERR(dev); | |
| if (status == 0) | |
| set_bit(FLAG_EXPORT, &desc->flags); | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| done: | |
| if (status) | |
| pr_debug("%s: gpio%d status %d\n", __func__, gpio, status); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_export); | |
| static int match_export(struct device *dev, void *data) | |
| { | |
| return dev_get_drvdata(dev) == data; | |
| } | |
| /** | |
| * gpio_export_link - create a sysfs link to an exported GPIO node | |
| * @dev: device under which to create symlink | |
| * @name: name of the symlink | |
| * @gpio: gpio to create symlink to, already exported | |
| * | |
| * Set up a symlink from /sys/.../dev/name to /sys/class/gpio/gpioN | |
| * node. Caller is responsible for unlinking. | |
| * | |
| * Returns zero on success, else an error. | |
| */ | |
| int gpio_export_link(struct device *dev, const char *name, unsigned gpio) | |
| { | |
| struct gpio_desc *desc; | |
| int status = -EINVAL; | |
| if (!gpio_is_valid(gpio)) | |
| goto done; | |
| mutex_lock(&sysfs_lock); | |
| desc = &gpio_desc[gpio]; | |
| if (test_bit(FLAG_EXPORT, &desc->flags)) { | |
| struct device *tdev; | |
| tdev = class_find_device(&gpio_class, NULL, desc, match_export); | |
| if (tdev != NULL) { | |
| status = sysfs_create_link(&dev->kobj, &tdev->kobj, | |
| name); | |
| } else { | |
| status = -ENODEV; | |
| } | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| done: | |
| if (status) | |
| pr_debug("%s: gpio%d status %d\n", __func__, gpio, status); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_export_link); | |
| /** | |
| * gpio_sysfs_set_active_low - set the polarity of gpio sysfs value | |
| * @gpio: gpio to change | |
| * @value: non-zero to use active low, i.e. inverted values | |
| * | |
| * Set the polarity of /sys/class/gpio/gpioN/value sysfs attribute. | |
| * The GPIO does not have to be exported yet. If poll(2) support has | |
| * been enabled for either rising or falling edge, it will be | |
| * reconfigured to follow the new polarity. | |
| * | |
| * Returns zero on success, else an error. | |
| */ | |
| int gpio_sysfs_set_active_low(unsigned gpio, int value) | |
| { | |
| struct gpio_desc *desc; | |
| struct device *dev = NULL; | |
| int status = -EINVAL; | |
| if (!gpio_is_valid(gpio)) | |
| goto done; | |
| mutex_lock(&sysfs_lock); | |
| desc = &gpio_desc[gpio]; | |
| if (test_bit(FLAG_EXPORT, &desc->flags)) { | |
| dev = class_find_device(&gpio_class, NULL, desc, match_export); | |
| if (dev == NULL) { | |
| status = -ENODEV; | |
| goto unlock; | |
| } | |
| } | |
| status = sysfs_set_active_low(desc, dev, value); | |
| unlock: | |
| mutex_unlock(&sysfs_lock); | |
| done: | |
| if (status) | |
| pr_debug("%s: gpio%d status %d\n", __func__, gpio, status); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_sysfs_set_active_low); | |
| /** | |
| * gpio_unexport - reverse effect of gpio_export() | |
| * @gpio: gpio to make unavailable | |
| * | |
| * This is implicit on gpio_free(). | |
| */ | |
| void gpio_unexport(unsigned gpio) | |
| { | |
| struct gpio_desc *desc; | |
| int status = 0; | |
| if (!gpio_is_valid(gpio)) { | |
| status = -EINVAL; | |
| goto done; | |
| } | |
| mutex_lock(&sysfs_lock); | |
| desc = &gpio_desc[gpio]; | |
| if (test_bit(FLAG_EXPORT, &desc->flags)) { | |
| struct device *dev = NULL; | |
| dev = class_find_device(&gpio_class, NULL, desc, match_export); | |
| if (dev) { | |
| gpio_setup_irq(desc, dev, 0); | |
| clear_bit(FLAG_EXPORT, &desc->flags); | |
| put_device(dev); | |
| device_unregister(dev); | |
| } else | |
| status = -ENODEV; | |
| } | |
| mutex_unlock(&sysfs_lock); | |
| done: | |
| if (status) | |
| pr_debug("%s: gpio%d status %d\n", __func__, gpio, status); | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_unexport); | |
| static int gpiochip_export(struct gpio_chip *chip) | |
| { | |
| int status; | |
| struct device *dev; | |
| /* Many systems register gpio chips for SOC support very early, | |
| * before driver model support is available. In those cases we | |
| * export this later, in gpiolib_sysfs_init() ... here we just | |
| * verify that _some_ field of gpio_class got initialized. | |
| */ | |
| if (!gpio_class.p) | |
| return 0; | |
| /* use chip->base for the ID; it's already known to be unique */ | |
| mutex_lock(&sysfs_lock); | |
| dev = device_create(&gpio_class, chip->dev, MKDEV(0, 0), chip, | |
| "gpiochip%d", chip->base); | |
| if (!IS_ERR(dev)) { | |
| status = sysfs_create_group(&dev->kobj, | |
| &gpiochip_attr_group); | |
| } else | |
| status = PTR_ERR(dev); | |
| chip->exported = (status == 0); | |
| mutex_unlock(&sysfs_lock); | |
| if (status) { | |
| unsigned long flags; | |
| unsigned gpio; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| gpio = chip->base; | |
| while (gpio_desc[gpio].chip == chip) | |
| gpio_desc[gpio++].chip = NULL; | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| pr_debug("%s: chip %s status %d\n", __func__, | |
| chip->label, status); | |
| } | |
| return status; | |
| } | |
| static void gpiochip_unexport(struct gpio_chip *chip) | |
| { | |
| int status; | |
| struct device *dev; | |
| mutex_lock(&sysfs_lock); | |
| dev = class_find_device(&gpio_class, NULL, chip, match_export); | |
| if (dev) { | |
| put_device(dev); | |
| device_unregister(dev); | |
| chip->exported = 0; | |
| status = 0; | |
| } else | |
| status = -ENODEV; | |
| mutex_unlock(&sysfs_lock); | |
| if (status) | |
| pr_debug("%s: chip %s status %d\n", __func__, | |
| chip->label, status); | |
| } | |
| static int __init gpiolib_sysfs_init(void) | |
| { | |
| int status; | |
| unsigned long flags; | |
| unsigned gpio; | |
| status = class_register(&gpio_class); | |
| if (status < 0) | |
| return status; | |
| /* Scan and register the gpio_chips which registered very | |
| * early (e.g. before the class_register above was called). | |
| * | |
| * We run before arch_initcall() so chip->dev nodes can have | |
| * registered, and so arch_initcall() can always gpio_export(). | |
| */ | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| for (gpio = 0; gpio < ARCH_NR_GPIOS; gpio++) { | |
| struct gpio_chip *chip; | |
| chip = gpio_desc[gpio].chip; | |
| if (!chip || chip->exported) | |
| continue; | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| status = gpiochip_export(chip); | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| } | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| return status; | |
| } | |
| postcore_initcall(gpiolib_sysfs_init); | |
| #else | |
| static inline int gpiochip_export(struct gpio_chip *chip) | |
| { | |
| return 0; | |
| } | |
| static inline void gpiochip_unexport(struct gpio_chip *chip) | |
| { | |
| } | |
| #endif /* CONFIG_GPIO_SYSFS */ | |
| /** | |
| * gpiochip_add() - register a gpio_chip | |
| * @chip: the chip to register, with chip->base initialized | |
| * Context: potentially before irqs or kmalloc will work | |
| * | |
| * Returns a negative errno if the chip can't be registered, such as | |
| * because the chip->base is invalid or already associated with a | |
| * different chip. Otherwise it returns zero as a success code. | |
| * | |
| * When gpiochip_add() is called very early during boot, so that GPIOs | |
| * can be freely used, the chip->dev device must be registered before | |
| * the gpio framework's arch_initcall(). Otherwise sysfs initialization | |
| * for GPIOs will fail rudely. | |
| * | |
| * If chip->base is negative, this requests dynamic assignment of | |
| * a range of valid GPIOs. | |
| */ | |
| int gpiochip_add(struct gpio_chip *chip) | |
| { | |
| unsigned long flags; | |
| int status = 0; | |
| unsigned id; | |
| int base = chip->base; | |
| if ((!gpio_is_valid(base) || !gpio_is_valid(base + chip->ngpio - 1)) | |
| && base >= 0) { | |
| status = -EINVAL; | |
| goto fail; | |
| } | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| if (base < 0) { | |
| base = gpiochip_find_base(chip->ngpio); | |
| if (base < 0) { | |
| status = base; | |
| goto unlock; | |
| } | |
| chip->base = base; | |
| } | |
| /* these GPIO numbers must not be managed by another gpio_chip */ | |
| for (id = base; id < base + chip->ngpio; id++) { | |
| if (gpio_desc[id].chip != NULL) { | |
| status = -EBUSY; | |
| break; | |
| } | |
| } | |
| if (status == 0) { | |
| for (id = base; id < base + chip->ngpio; id++) { | |
| gpio_desc[id].chip = chip; | |
| /* REVISIT: most hardware initializes GPIOs as | |
| * inputs (often with pullups enabled) so power | |
| * usage is minimized. Linux code should set the | |
| * gpio direction first thing; but until it does, | |
| * we may expose the wrong direction in sysfs. | |
| */ | |
| gpio_desc[id].flags = !chip->direction_input | |
| ? (1 << FLAG_IS_OUT) | |
| : 0; | |
| } | |
| } | |
| of_gpiochip_add(chip); | |
| unlock: | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| if (status) | |
| goto fail; | |
| status = gpiochip_export(chip); | |
| if (status) | |
| goto fail; | |
| return 0; | |
| fail: | |
| /* failures here can mean systems won't boot... */ | |
| pr_err("gpiochip_add: gpios %d..%d (%s) failed to register\n", | |
| chip->base, chip->base + chip->ngpio - 1, | |
| chip->label ? : "generic"); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpiochip_add); | |
| /** | |
| * gpiochip_remove() - unregister a gpio_chip | |
| * @chip: the chip to unregister | |
| * | |
| * A gpio_chip with any GPIOs still requested may not be removed. | |
| */ | |
| int gpiochip_remove(struct gpio_chip *chip) | |
| { | |
| unsigned long flags; | |
| int status = 0; | |
| unsigned id; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| of_gpiochip_remove(chip); | |
| for (id = chip->base; id < chip->base + chip->ngpio; id++) { | |
| if (test_bit(FLAG_REQUESTED, &gpio_desc[id].flags)) { | |
| status = -EBUSY; | |
| break; | |
| } | |
| } | |
| if (status == 0) { | |
| for (id = chip->base; id < chip->base + chip->ngpio; id++) | |
| gpio_desc[id].chip = NULL; | |
| } | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| if (status == 0) | |
| gpiochip_unexport(chip); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpiochip_remove); | |
| /** | |
| * gpiochip_find() - iterator for locating a specific gpio_chip | |
| * @data: data to pass to match function | |
| * @callback: Callback function to check gpio_chip | |
| * | |
| * Similar to bus_find_device. It returns a reference to a gpio_chip as | |
| * determined by a user supplied @match callback. The callback should return | |
| * 0 if the device doesn't match and non-zero if it does. If the callback is | |
| * non-zero, this function will return to the caller and not iterate over any | |
| * more gpio_chips. | |
| */ | |
| struct gpio_chip *gpiochip_find(void *data, | |
| int (*match)(struct gpio_chip *chip, void *data)) | |
| { | |
| struct gpio_chip *chip = NULL; | |
| unsigned long flags; | |
| int i; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| for (i = 0; i < ARCH_NR_GPIOS; i++) { | |
| if (!gpio_desc[i].chip) | |
| continue; | |
| if (match(gpio_desc[i].chip, data)) { | |
| chip = gpio_desc[i].chip; | |
| break; | |
| } | |
| } | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| return chip; | |
| } | |
| EXPORT_SYMBOL_GPL(gpiochip_find); | |
| /* These "optional" allocation calls help prevent drivers from stomping | |
| * on each other, and help provide better diagnostics in debugfs. | |
| * They're called even less than the "set direction" calls. | |
| */ | |
| int gpio_request(unsigned gpio, const char *label) | |
| { | |
| struct gpio_desc *desc; | |
| struct gpio_chip *chip; | |
| int status = -EINVAL; | |
| unsigned long flags; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| if (!gpio_is_valid(gpio)) | |
| goto done; | |
| desc = &gpio_desc[gpio]; | |
| chip = desc->chip; | |
| if (chip == NULL) | |
| goto done; | |
| if (!try_module_get(chip->owner)) | |
| goto done; | |
| /* NOTE: gpio_request() can be called in early boot, | |
| * before IRQs are enabled, for non-sleeping (SOC) GPIOs. | |
| */ | |
| if (test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0) { | |
| desc_set_label(desc, label ? : "?"); | |
| status = 0; | |
| } else { | |
| status = -EBUSY; | |
| module_put(chip->owner); | |
| goto done; | |
| } | |
| if (chip->request) { | |
| /* chip->request may sleep */ | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| status = chip->request(chip, gpio - chip->base); | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| if (status < 0) { | |
| desc_set_label(desc, NULL); | |
| module_put(chip->owner); | |
| clear_bit(FLAG_REQUESTED, &desc->flags); | |
| } | |
| } | |
| done: | |
| if (status) | |
| pr_debug("gpio_request: gpio-%d (%s) status %d\n", | |
| gpio, label ? : "?", status); | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_request); | |
| void gpio_free(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| struct gpio_desc *desc; | |
| struct gpio_chip *chip; | |
| might_sleep(); | |
| if (!gpio_is_valid(gpio)) { | |
| WARN_ON(extra_checks); | |
| return; | |
| } | |
| gpio_unexport(gpio); | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| desc = &gpio_desc[gpio]; | |
| chip = desc->chip; | |
| if (chip && test_bit(FLAG_REQUESTED, &desc->flags)) { | |
| if (chip->free) { | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| might_sleep_if(chip->can_sleep); | |
| chip->free(chip, gpio - chip->base); | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| } | |
| desc_set_label(desc, NULL); | |
| module_put(desc->chip->owner); | |
| clear_bit(FLAG_ACTIVE_LOW, &desc->flags); | |
| clear_bit(FLAG_REQUESTED, &desc->flags); | |
| } else | |
| WARN_ON(extra_checks); | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_free); | |
| /** | |
| * gpio_request_one - request a single GPIO with initial configuration | |
| * @gpio: the GPIO number | |
| * @flags: GPIO configuration as specified by GPIOF_* | |
| * @label: a literal description string of this GPIO | |
| */ | |
| int gpio_request_one(unsigned gpio, unsigned long flags, const char *label) | |
| { | |
| int err; | |
| err = gpio_request(gpio, label); | |
| if (err) | |
| return err; | |
| if (flags & GPIOF_DIR_IN) | |
| err = gpio_direction_input(gpio); | |
| else | |
| err = gpio_direction_output(gpio, | |
| (flags & GPIOF_INIT_HIGH) ? 1 : 0); | |
| if (err) | |
| gpio_free(gpio); | |
| return err; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_request_one); | |
| /** | |
| * gpio_request_array - request multiple GPIOs in a single call | |
| * @array: array of the 'struct gpio' | |
| * @num: how many GPIOs in the array | |
| */ | |
| int gpio_request_array(const struct gpio *array, size_t num) | |
| { | |
| int i, err; | |
| for (i = 0; i < num; i++, array++) { | |
| err = gpio_request_one(array->gpio, array->flags, array->label); | |
| if (err) | |
| goto err_free; | |
| } | |
| return 0; | |
| err_free: | |
| while (i--) | |
| gpio_free((--array)->gpio); | |
| return err; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_request_array); | |
| /** | |
| * gpio_free_array - release multiple GPIOs in a single call | |
| * @array: array of the 'struct gpio' | |
| * @num: how many GPIOs in the array | |
| */ | |
| void gpio_free_array(const struct gpio *array, size_t num) | |
| { | |
| while (num--) | |
| gpio_free((array++)->gpio); | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_free_array); | |
| /** | |
| * gpiochip_is_requested - return string iff signal was requested | |
| * @chip: controller managing the signal | |
| * @offset: of signal within controller's 0..(ngpio - 1) range | |
| * | |
| * Returns NULL if the GPIO is not currently requested, else a string. | |
| * If debugfs support is enabled, the string returned is the label passed | |
| * to gpio_request(); otherwise it is a meaningless constant. | |
| * | |
| * This function is for use by GPIO controller drivers. The label can | |
| * help with diagnostics, and knowing that the signal is used as a GPIO | |
| * can help avoid accidentally multiplexing it to another controller. | |
| */ | |
| const char *gpiochip_is_requested(struct gpio_chip *chip, unsigned offset) | |
| { | |
| unsigned gpio = chip->base + offset; | |
| if (!gpio_is_valid(gpio) || gpio_desc[gpio].chip != chip) | |
| return NULL; | |
| if (test_bit(FLAG_REQUESTED, &gpio_desc[gpio].flags) == 0) | |
| return NULL; | |
| #ifdef CONFIG_DEBUG_FS | |
| return gpio_desc[gpio].label; | |
| #else | |
| return "?"; | |
| #endif | |
| } | |
| EXPORT_SYMBOL_GPL(gpiochip_is_requested); | |
| /* Drivers MUST set GPIO direction before making get/set calls. In | |
| * some cases this is done in early boot, before IRQs are enabled. | |
| * | |
| * As a rule these aren't called more than once (except for drivers | |
| * using the open-drain emulation idiom) so these are natural places | |
| * to accumulate extra debugging checks. Note that we can't (yet) | |
| * rely on gpio_request() having been called beforehand. | |
| */ | |
| int gpio_direction_input(unsigned gpio) | |
| { | |
| unsigned long flags; | |
| struct gpio_chip *chip; | |
| struct gpio_desc *desc = &gpio_desc[gpio]; | |
| int status = -EINVAL; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| if (!gpio_is_valid(gpio)) | |
| goto fail; | |
| chip = desc->chip; | |
| if (!chip || !chip->get || !chip->direction_input) | |
| goto fail; | |
| gpio -= chip->base; | |
| if (gpio >= chip->ngpio) | |
| goto fail; | |
| status = gpio_ensure_requested(desc, gpio); | |
| if (status < 0) | |
| goto fail; | |
| /* now we know the gpio is valid and chip won't vanish */ | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| might_sleep_if(chip->can_sleep); | |
| if (status) { | |
| status = chip->request(chip, gpio); | |
| if (status < 0) { | |
| pr_debug("GPIO-%d: chip request fail, %d\n", | |
| chip->base + gpio, status); | |
| /* and it's not available to anyone else ... | |
| * gpio_request() is the fully clean solution. | |
| */ | |
| goto lose; | |
| } | |
| } | |
| status = chip->direction_input(chip, gpio); | |
| if (status == 0) | |
| clear_bit(FLAG_IS_OUT, &desc->flags); | |
| trace_gpio_direction(chip->base + gpio, 1, status); | |
| lose: | |
| return status; | |
| fail: | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| if (status) | |
| pr_debug("%s: gpio-%d status %d\n", | |
| __func__, gpio, status); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_direction_input); | |
| int gpio_direction_output(unsigned gpio, int value) | |
| { | |
| unsigned long flags; | |
| struct gpio_chip *chip; | |
| struct gpio_desc *desc = &gpio_desc[gpio]; | |
| int status = -EINVAL; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| if (!gpio_is_valid(gpio)) | |
| goto fail; | |
| chip = desc->chip; | |
| if (!chip || !chip->set || !chip->direction_output) | |
| goto fail; | |
| gpio -= chip->base; | |
| if (gpio >= chip->ngpio) | |
| goto fail; | |
| status = gpio_ensure_requested(desc, gpio); | |
| if (status < 0) | |
| goto fail; | |
| /* now we know the gpio is valid and chip won't vanish */ | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| might_sleep_if(chip->can_sleep); | |
| if (status) { | |
| status = chip->request(chip, gpio); | |
| if (status < 0) { | |
| pr_debug("GPIO-%d: chip request fail, %d\n", | |
| chip->base + gpio, status); | |
| /* and it's not available to anyone else ... | |
| * gpio_request() is the fully clean solution. | |
| */ | |
| goto lose; | |
| } | |
| } | |
| status = chip->direction_output(chip, gpio, value); | |
| if (status == 0) | |
| set_bit(FLAG_IS_OUT, &desc->flags); | |
| trace_gpio_value(chip->base + gpio, 0, value); | |
| trace_gpio_direction(chip->base + gpio, 0, status); | |
| lose: | |
| return status; | |
| fail: | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| if (status) | |
| pr_debug("%s: gpio-%d status %d\n", | |
| __func__, gpio, status); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_direction_output); | |
| /** | |
| * gpio_set_debounce - sets @debounce time for a @gpio | |
| * @gpio: the gpio to set debounce time | |
| * @debounce: debounce time is microseconds | |
| */ | |
| int gpio_set_debounce(unsigned gpio, unsigned debounce) | |
| { | |
| unsigned long flags; | |
| struct gpio_chip *chip; | |
| struct gpio_desc *desc = &gpio_desc[gpio]; | |
| int status = -EINVAL; | |
| spin_lock_irqsave(&gpio_lock, flags); | |
| if (!gpio_is_valid(gpio)) | |
| goto fail; | |
| chip = desc->chip; | |
| if (!chip || !chip->set || !chip->set_debounce) | |
| goto fail; | |
| gpio -= chip->base; | |
| if (gpio >= chip->ngpio) | |
| goto fail; | |
| status = gpio_ensure_requested(desc, gpio); | |
| if (status < 0) | |
| goto fail; | |
| /* now we know the gpio is valid and chip won't vanish */ | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| might_sleep_if(chip->can_sleep); | |
| return chip->set_debounce(chip, gpio, debounce); | |
| fail: | |
| spin_unlock_irqrestore(&gpio_lock, flags); | |
| if (status) | |
| pr_debug("%s: gpio-%d status %d\n", | |
| __func__, gpio, status); | |
| return status; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_set_debounce); | |
| /* I/O calls are only valid after configuration completed; the relevant | |
| * "is this a valid GPIO" error checks should already have been done. | |
| * | |
| * "Get" operations are often inlinable as reading a pin value register, | |
| * and masking the relevant bit in that register. | |
| * | |
| * When "set" operations are inlinable, they involve writing that mask to | |
| * one register to set a low value, or a different register to set it high. | |
| * Otherwise locking is needed, so there may be little value to inlining. | |
| * | |
| *------------------------------------------------------------------------ | |
| * | |
| * IMPORTANT!!! The hot paths -- get/set value -- assume that callers | |
| * have requested the GPIO. That can include implicit requesting by | |
| * a direction setting call. Marking a gpio as requested locks its chip | |
| * in memory, guaranteeing that these table lookups need no more locking | |
| * and that gpiochip_remove() will fail. | |
| * | |
| * REVISIT when debugging, consider adding some instrumentation to ensure | |
| * that the GPIO was actually requested. | |
| */ | |
| /** | |
| * __gpio_get_value() - return a gpio's value | |
| * @gpio: gpio whose value will be returned | |
| * Context: any | |
| * | |
| * This is used directly or indirectly to implement gpio_get_value(). | |
| * It returns the zero or nonzero value provided by the associated | |
| * gpio_chip.get() method; or zero if no such method is provided. | |
| */ | |
| int __gpio_get_value(unsigned gpio) | |
| { | |
| struct gpio_chip *chip; | |
| int value; | |
| chip = gpio_to_chip(gpio); | |
| WARN_ON(chip->can_sleep); | |
| value = chip->get ? chip->get(chip, gpio - chip->base) : 0; | |
| trace_gpio_value(gpio, 1, value); | |
| return value; | |
| } | |
| EXPORT_SYMBOL_GPL(__gpio_get_value); | |
| /** | |
| * __gpio_set_value() - assign a gpio's value | |
| * @gpio: gpio whose value will be assigned | |
| * @value: value to assign | |
| * Context: any | |
| * | |
| * This is used directly or indirectly to implement gpio_set_value(). | |
| * It invokes the associated gpio_chip.set() method. | |
| */ | |
| void __gpio_set_value(unsigned gpio, int value) | |
| { | |
| struct gpio_chip *chip; | |
| chip = gpio_to_chip(gpio); | |
| WARN_ON(chip->can_sleep); | |
| trace_gpio_value(gpio, 0, value); | |
| chip->set(chip, gpio - chip->base, value); | |
| } | |
| EXPORT_SYMBOL_GPL(__gpio_set_value); | |
| /** | |
| * __gpio_cansleep() - report whether gpio value access will sleep | |
| * @gpio: gpio in question | |
| * Context: any | |
| * | |
| * This is used directly or indirectly to implement gpio_cansleep(). It | |
| * returns nonzero if access reading or writing the GPIO value can sleep. | |
| */ | |
| int __gpio_cansleep(unsigned gpio) | |
| { | |
| struct gpio_chip *chip; | |
| /* only call this on GPIOs that are valid! */ | |
| chip = gpio_to_chip(gpio); | |
| return chip->can_sleep; | |
| } | |
| EXPORT_SYMBOL_GPL(__gpio_cansleep); | |
| /** | |
| * __gpio_to_irq() - return the IRQ corresponding to a GPIO | |
| * @gpio: gpio whose IRQ will be returned (already requested) | |
| * Context: any | |
| * | |
| * This is used directly or indirectly to implement gpio_to_irq(). | |
| * It returns the number of the IRQ signaled by this (input) GPIO, | |
| * or a negative errno. | |
| */ | |
| int __gpio_to_irq(unsigned gpio) | |
| { | |
| struct gpio_chip *chip; | |
| chip = gpio_to_chip(gpio); | |
| return chip->to_irq ? chip->to_irq(chip, gpio - chip->base) : -ENXIO; | |
| } | |
| EXPORT_SYMBOL_GPL(__gpio_to_irq); | |
| /* There's no value in making it easy to inline GPIO calls that may sleep. | |
| * Common examples include ones connected to I2C or SPI chips. | |
| */ | |
| int gpio_get_value_cansleep(unsigned gpio) | |
| { | |
| struct gpio_chip *chip; | |
| int value; | |
| might_sleep_if(extra_checks); | |
| chip = gpio_to_chip(gpio); | |
| value = chip->get ? chip->get(chip, gpio - chip->base) : 0; | |
| trace_gpio_value(gpio, 1, value); | |
| return value; | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_get_value_cansleep); | |
| void gpio_set_value_cansleep(unsigned gpio, int value) | |
| { | |
| struct gpio_chip *chip; | |
| might_sleep_if(extra_checks); | |
| chip = gpio_to_chip(gpio); | |
| trace_gpio_value(gpio, 0, value); | |
| chip->set(chip, gpio - chip->base, value); | |
| } | |
| EXPORT_SYMBOL_GPL(gpio_set_value_cansleep); | |
| #ifdef CONFIG_DEBUG_FS | |
| static void gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip) | |
| { | |
| unsigned i; | |
| unsigned gpio = chip->base; | |
| struct gpio_desc *gdesc = &gpio_desc[gpio]; | |
| int is_out; | |
| for (i = 0; i < chip->ngpio; i++, gpio++, gdesc++) { | |
| if (!test_bit(FLAG_REQUESTED, &gdesc->flags)) | |
| continue; | |
| is_out = test_bit(FLAG_IS_OUT, &gdesc->flags); | |
| seq_printf(s, " gpio-%-3d (%-20.20s) %s %s", | |
| gpio, gdesc->label, | |
| is_out ? "out" : "in ", | |
| chip->get | |
| ? (chip->get(chip, i) ? "hi" : "lo") | |
| : "? "); | |
| seq_printf(s, "\n"); | |
| } | |
| } | |
| static int gpiolib_show(struct seq_file *s, void *unused) | |
| { | |
| struct gpio_chip *chip = NULL; | |
| unsigned gpio; | |
| int started = 0; | |
| /* REVISIT this isn't locked against gpio_chip removal ... */ | |
| for (gpio = 0; gpio_is_valid(gpio); gpio++) { | |
| struct device *dev; | |
| if (chip == gpio_desc[gpio].chip) | |
| continue; | |
| chip = gpio_desc[gpio].chip; | |
| if (!chip) | |
| continue; | |
| seq_printf(s, "%sGPIOs %d-%d", | |
| started ? "\n" : "", | |
| chip->base, chip->base + chip->ngpio - 1); | |
| dev = chip->dev; | |
| if (dev) | |
| seq_printf(s, ", %s/%s", | |
| dev->bus ? dev->bus->name : "no-bus", | |
| dev_name(dev)); | |
| if (chip->label) | |
| seq_printf(s, ", %s", chip->label); | |
| if (chip->can_sleep) | |
| seq_printf(s, ", can sleep"); | |
| seq_printf(s, ":\n"); | |
| started = 1; | |
| if (chip->dbg_show) | |
| chip->dbg_show(s, chip); | |
| else | |
| gpiolib_dbg_show(s, chip); | |
| } | |
| return 0; | |
| } | |
| static int gpiolib_open(struct inode *inode, struct file *file) | |
| { | |
| return single_open(file, gpiolib_show, NULL); | |
| } | |
| static const struct file_operations gpiolib_operations = { | |
| .open = gpiolib_open, | |
| .read = seq_read, | |
| .llseek = seq_lseek, | |
| .release = single_release, | |
| }; | |
| static int __init gpiolib_debugfs_init(void) | |
| { | |
| /* /sys/kernel/debug/gpio */ | |
| (void) debugfs_create_file("gpio", S_IFREG | S_IRUGO, | |
| NULL, NULL, &gpiolib_operations); | |
| return 0; | |
| } | |
| subsys_initcall(gpiolib_debugfs_init); | |
| #endif /* DEBUG_FS */ |