| /* | |
| * drivers/net/gianfar.c | |
| * | |
| * Gianfar Ethernet Driver | |
| * This driver is designed for the non-CPM ethernet controllers | |
| * on the 85xx and 83xx family of integrated processors | |
| * Based on 8260_io/fcc_enet.c | |
| * | |
| * Author: Andy Fleming | |
| * Maintainer: Kumar Gala | |
| * Modifier: Sandeep Gopalpet <sandeep.kumar@freescale.com> | |
| * | |
| * Copyright 2002-2009, 2011 Freescale Semiconductor, Inc. | |
| * Copyright 2007 MontaVista Software, Inc. | |
| * | |
| * This program is free software; you can redistribute it and/or modify it | |
| * under the terms of the GNU General Public License as published by the | |
| * Free Software Foundation; either version 2 of the License, or (at your | |
| * option) any later version. | |
| * | |
| * Gianfar: AKA Lambda Draconis, "Dragon" | |
| * RA 11 31 24.2 | |
| * Dec +69 19 52 | |
| * V 3.84 | |
| * B-V +1.62 | |
| * | |
| * Theory of operation | |
| * | |
| * The driver is initialized through of_device. Configuration information | |
| * is therefore conveyed through an OF-style device tree. | |
| * | |
| * The Gianfar Ethernet Controller uses a ring of buffer | |
| * descriptors. The beginning is indicated by a register | |
| * pointing to the physical address of the start of the ring. | |
| * The end is determined by a "wrap" bit being set in the | |
| * last descriptor of the ring. | |
| * | |
| * When a packet is received, the RXF bit in the | |
| * IEVENT register is set, triggering an interrupt when the | |
| * corresponding bit in the IMASK register is also set (if | |
| * interrupt coalescing is active, then the interrupt may not | |
| * happen immediately, but will wait until either a set number | |
| * of frames or amount of time have passed). In NAPI, the | |
| * interrupt handler will signal there is work to be done, and | |
| * exit. This method will start at the last known empty | |
| * descriptor, and process every subsequent descriptor until there | |
| * are none left with data (NAPI will stop after a set number of | |
| * packets to give time to other tasks, but will eventually | |
| * process all the packets). The data arrives inside a | |
| * pre-allocated skb, and so after the skb is passed up to the | |
| * stack, a new skb must be allocated, and the address field in | |
| * the buffer descriptor must be updated to indicate this new | |
| * skb. | |
| * | |
| * When the kernel requests that a packet be transmitted, the | |
| * driver starts where it left off last time, and points the | |
| * descriptor at the buffer which was passed in. The driver | |
| * then informs the DMA engine that there are packets ready to | |
| * be transmitted. Once the controller is finished transmitting | |
| * the packet, an interrupt may be triggered (under the same | |
| * conditions as for reception, but depending on the TXF bit). | |
| * The driver then cleans up the buffer. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/string.h> | |
| #include <linux/errno.h> | |
| #include <linux/unistd.h> | |
| #include <linux/slab.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/init.h> | |
| #include <linux/delay.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/etherdevice.h> | |
| #include <linux/skbuff.h> | |
| #include <linux/if_vlan.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/mm.h> | |
| #include <linux/of_mdio.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/ip.h> | |
| #include <linux/tcp.h> | |
| #include <linux/udp.h> | |
| #include <linux/in.h> | |
| #include <linux/net_tstamp.h> | |
| #include <asm/io.h> | |
| #include <asm/reg.h> | |
| #include <asm/irq.h> | |
| #include <asm/uaccess.h> | |
| #include <linux/module.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/crc32.h> | |
| #include <linux/mii.h> | |
| #include <linux/phy.h> | |
| #include <linux/phy_fixed.h> | |
| #include <linux/of.h> | |
| #include <linux/of_net.h> | |
| #include "gianfar.h" | |
| #include "fsl_pq_mdio.h" | |
| #define TX_TIMEOUT (1*HZ) | |
| #undef BRIEF_GFAR_ERRORS | |
| #undef VERBOSE_GFAR_ERRORS | |
| const char gfar_driver_name[] = "Gianfar Ethernet"; | |
| const char gfar_driver_version[] = "1.3"; | |
| static int gfar_enet_open(struct net_device *dev); | |
| static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev); | |
| static void gfar_reset_task(struct work_struct *work); | |
| static void gfar_timeout(struct net_device *dev); | |
| static int gfar_close(struct net_device *dev); | |
| struct sk_buff *gfar_new_skb(struct net_device *dev); | |
| static void gfar_new_rxbdp(struct gfar_priv_rx_q *rx_queue, struct rxbd8 *bdp, | |
| struct sk_buff *skb); | |
| static int gfar_set_mac_address(struct net_device *dev); | |
| static int gfar_change_mtu(struct net_device *dev, int new_mtu); | |
| static irqreturn_t gfar_error(int irq, void *dev_id); | |
| static irqreturn_t gfar_transmit(int irq, void *dev_id); | |
| static irqreturn_t gfar_interrupt(int irq, void *dev_id); | |
| static void adjust_link(struct net_device *dev); | |
| static void init_registers(struct net_device *dev); | |
| static int init_phy(struct net_device *dev); | |
| static int gfar_probe(struct platform_device *ofdev); | |
| static int gfar_remove(struct platform_device *ofdev); | |
| static void free_skb_resources(struct gfar_private *priv); | |
| static void gfar_set_multi(struct net_device *dev); | |
| static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr); | |
| static void gfar_configure_serdes(struct net_device *dev); | |
| static int gfar_poll(struct napi_struct *napi, int budget); | |
| #ifdef CONFIG_NET_POLL_CONTROLLER | |
| static void gfar_netpoll(struct net_device *dev); | |
| #endif | |
| int gfar_clean_rx_ring(struct gfar_priv_rx_q *rx_queue, int rx_work_limit); | |
| static int gfar_clean_tx_ring(struct gfar_priv_tx_q *tx_queue); | |
| static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, | |
| int amount_pull); | |
| static void gfar_vlan_rx_register(struct net_device *netdev, | |
| struct vlan_group *grp); | |
| void gfar_halt(struct net_device *dev); | |
| static void gfar_halt_nodisable(struct net_device *dev); | |
| void gfar_start(struct net_device *dev); | |
| static void gfar_clear_exact_match(struct net_device *dev); | |
| static void gfar_set_mac_for_addr(struct net_device *dev, int num, | |
| const u8 *addr); | |
| static int gfar_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); | |
| MODULE_AUTHOR("Freescale Semiconductor, Inc"); | |
| MODULE_DESCRIPTION("Gianfar Ethernet Driver"); | |
| MODULE_LICENSE("GPL"); | |
| static void gfar_init_rxbdp(struct gfar_priv_rx_q *rx_queue, struct rxbd8 *bdp, | |
| dma_addr_t buf) | |
| { | |
| u32 lstatus; | |
| bdp->bufPtr = buf; | |
| lstatus = BD_LFLAG(RXBD_EMPTY | RXBD_INTERRUPT); | |
| if (bdp == rx_queue->rx_bd_base + rx_queue->rx_ring_size - 1) | |
| lstatus |= BD_LFLAG(RXBD_WRAP); | |
| eieio(); | |
| bdp->lstatus = lstatus; | |
| } | |
| static int gfar_init_bds(struct net_device *ndev) | |
| { | |
| struct gfar_private *priv = netdev_priv(ndev); | |
| struct gfar_priv_tx_q *tx_queue = NULL; | |
| struct gfar_priv_rx_q *rx_queue = NULL; | |
| struct txbd8 *txbdp; | |
| struct rxbd8 *rxbdp; | |
| int i, j; | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| tx_queue = priv->tx_queue[i]; | |
| /* Initialize some variables in our dev structure */ | |
| tx_queue->num_txbdfree = tx_queue->tx_ring_size; | |
| tx_queue->dirty_tx = tx_queue->tx_bd_base; | |
| tx_queue->cur_tx = tx_queue->tx_bd_base; | |
| tx_queue->skb_curtx = 0; | |
| tx_queue->skb_dirtytx = 0; | |
| /* Initialize Transmit Descriptor Ring */ | |
| txbdp = tx_queue->tx_bd_base; | |
| for (j = 0; j < tx_queue->tx_ring_size; j++) { | |
| txbdp->lstatus = 0; | |
| txbdp->bufPtr = 0; | |
| txbdp++; | |
| } | |
| /* Set the last descriptor in the ring to indicate wrap */ | |
| txbdp--; | |
| txbdp->status |= TXBD_WRAP; | |
| } | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| rx_queue = priv->rx_queue[i]; | |
| rx_queue->cur_rx = rx_queue->rx_bd_base; | |
| rx_queue->skb_currx = 0; | |
| rxbdp = rx_queue->rx_bd_base; | |
| for (j = 0; j < rx_queue->rx_ring_size; j++) { | |
| struct sk_buff *skb = rx_queue->rx_skbuff[j]; | |
| if (skb) { | |
| gfar_init_rxbdp(rx_queue, rxbdp, | |
| rxbdp->bufPtr); | |
| } else { | |
| skb = gfar_new_skb(ndev); | |
| if (!skb) { | |
| pr_err("%s: Can't allocate RX buffers\n", | |
| ndev->name); | |
| goto err_rxalloc_fail; | |
| } | |
| rx_queue->rx_skbuff[j] = skb; | |
| gfar_new_rxbdp(rx_queue, rxbdp, skb); | |
| } | |
| rxbdp++; | |
| } | |
| } | |
| return 0; | |
| err_rxalloc_fail: | |
| free_skb_resources(priv); | |
| return -ENOMEM; | |
| } | |
| static int gfar_alloc_skb_resources(struct net_device *ndev) | |
| { | |
| void *vaddr; | |
| dma_addr_t addr; | |
| int i, j, k; | |
| struct gfar_private *priv = netdev_priv(ndev); | |
| struct device *dev = &priv->ofdev->dev; | |
| struct gfar_priv_tx_q *tx_queue = NULL; | |
| struct gfar_priv_rx_q *rx_queue = NULL; | |
| priv->total_tx_ring_size = 0; | |
| for (i = 0; i < priv->num_tx_queues; i++) | |
| priv->total_tx_ring_size += priv->tx_queue[i]->tx_ring_size; | |
| priv->total_rx_ring_size = 0; | |
| for (i = 0; i < priv->num_rx_queues; i++) | |
| priv->total_rx_ring_size += priv->rx_queue[i]->rx_ring_size; | |
| /* Allocate memory for the buffer descriptors */ | |
| vaddr = dma_alloc_coherent(dev, | |
| sizeof(struct txbd8) * priv->total_tx_ring_size + | |
| sizeof(struct rxbd8) * priv->total_rx_ring_size, | |
| &addr, GFP_KERNEL); | |
| if (!vaddr) { | |
| if (netif_msg_ifup(priv)) | |
| pr_err("%s: Could not allocate buffer descriptors!\n", | |
| ndev->name); | |
| return -ENOMEM; | |
| } | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| tx_queue = priv->tx_queue[i]; | |
| tx_queue->tx_bd_base = (struct txbd8 *) vaddr; | |
| tx_queue->tx_bd_dma_base = addr; | |
| tx_queue->dev = ndev; | |
| /* enet DMA only understands physical addresses */ | |
| addr += sizeof(struct txbd8) *tx_queue->tx_ring_size; | |
| vaddr += sizeof(struct txbd8) *tx_queue->tx_ring_size; | |
| } | |
| /* Start the rx descriptor ring where the tx ring leaves off */ | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| rx_queue = priv->rx_queue[i]; | |
| rx_queue->rx_bd_base = (struct rxbd8 *) vaddr; | |
| rx_queue->rx_bd_dma_base = addr; | |
| rx_queue->dev = ndev; | |
| addr += sizeof (struct rxbd8) * rx_queue->rx_ring_size; | |
| vaddr += sizeof (struct rxbd8) * rx_queue->rx_ring_size; | |
| } | |
| /* Setup the skbuff rings */ | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| tx_queue = priv->tx_queue[i]; | |
| tx_queue->tx_skbuff = kmalloc(sizeof(*tx_queue->tx_skbuff) * | |
| tx_queue->tx_ring_size, GFP_KERNEL); | |
| if (!tx_queue->tx_skbuff) { | |
| if (netif_msg_ifup(priv)) | |
| pr_err("%s: Could not allocate tx_skbuff\n", | |
| ndev->name); | |
| goto cleanup; | |
| } | |
| for (k = 0; k < tx_queue->tx_ring_size; k++) | |
| tx_queue->tx_skbuff[k] = NULL; | |
| } | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| rx_queue = priv->rx_queue[i]; | |
| rx_queue->rx_skbuff = kmalloc(sizeof(*rx_queue->rx_skbuff) * | |
| rx_queue->rx_ring_size, GFP_KERNEL); | |
| if (!rx_queue->rx_skbuff) { | |
| if (netif_msg_ifup(priv)) | |
| pr_err("%s: Could not allocate rx_skbuff\n", | |
| ndev->name); | |
| goto cleanup; | |
| } | |
| for (j = 0; j < rx_queue->rx_ring_size; j++) | |
| rx_queue->rx_skbuff[j] = NULL; | |
| } | |
| if (gfar_init_bds(ndev)) | |
| goto cleanup; | |
| return 0; | |
| cleanup: | |
| free_skb_resources(priv); | |
| return -ENOMEM; | |
| } | |
| static void gfar_init_tx_rx_base(struct gfar_private *priv) | |
| { | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 __iomem *baddr; | |
| int i; | |
| baddr = ®s->tbase0; | |
| for(i = 0; i < priv->num_tx_queues; i++) { | |
| gfar_write(baddr, priv->tx_queue[i]->tx_bd_dma_base); | |
| baddr += 2; | |
| } | |
| baddr = ®s->rbase0; | |
| for(i = 0; i < priv->num_rx_queues; i++) { | |
| gfar_write(baddr, priv->rx_queue[i]->rx_bd_dma_base); | |
| baddr += 2; | |
| } | |
| } | |
| static void gfar_init_mac(struct net_device *ndev) | |
| { | |
| struct gfar_private *priv = netdev_priv(ndev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 rctrl = 0; | |
| u32 tctrl = 0; | |
| u32 attrs = 0; | |
| /* write the tx/rx base registers */ | |
| gfar_init_tx_rx_base(priv); | |
| /* Configure the coalescing support */ | |
| gfar_configure_coalescing(priv, 0xFF, 0xFF); | |
| if (priv->rx_filer_enable) { | |
| rctrl |= RCTRL_FILREN; | |
| /* Program the RIR0 reg with the required distribution */ | |
| gfar_write(®s->rir0, DEFAULT_RIR0); | |
| } | |
| if (ndev->features & NETIF_F_RXCSUM) | |
| rctrl |= RCTRL_CHECKSUMMING; | |
| if (priv->extended_hash) { | |
| rctrl |= RCTRL_EXTHASH; | |
| gfar_clear_exact_match(ndev); | |
| rctrl |= RCTRL_EMEN; | |
| } | |
| if (priv->padding) { | |
| rctrl &= ~RCTRL_PAL_MASK; | |
| rctrl |= RCTRL_PADDING(priv->padding); | |
| } | |
| /* Insert receive time stamps into padding alignment bytes */ | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_TIMER) { | |
| rctrl &= ~RCTRL_PAL_MASK; | |
| rctrl |= RCTRL_PADDING(8); | |
| priv->padding = 8; | |
| } | |
| /* Enable HW time stamping if requested from user space */ | |
| if (priv->hwts_rx_en) | |
| rctrl |= RCTRL_PRSDEP_INIT | RCTRL_TS_ENABLE; | |
| /* keep vlan related bits if it's enabled */ | |
| if (priv->vlgrp) { | |
| rctrl |= RCTRL_VLEX | RCTRL_PRSDEP_INIT; | |
| tctrl |= TCTRL_VLINS; | |
| } | |
| /* Init rctrl based on our settings */ | |
| gfar_write(®s->rctrl, rctrl); | |
| if (ndev->features & NETIF_F_IP_CSUM) | |
| tctrl |= TCTRL_INIT_CSUM; | |
| tctrl |= TCTRL_TXSCHED_PRIO; | |
| gfar_write(®s->tctrl, tctrl); | |
| /* Set the extraction length and index */ | |
| attrs = ATTRELI_EL(priv->rx_stash_size) | | |
| ATTRELI_EI(priv->rx_stash_index); | |
| gfar_write(®s->attreli, attrs); | |
| /* Start with defaults, and add stashing or locking | |
| * depending on the approprate variables */ | |
| attrs = ATTR_INIT_SETTINGS; | |
| if (priv->bd_stash_en) | |
| attrs |= ATTR_BDSTASH; | |
| if (priv->rx_stash_size != 0) | |
| attrs |= ATTR_BUFSTASH; | |
| gfar_write(®s->attr, attrs); | |
| gfar_write(®s->fifo_tx_thr, priv->fifo_threshold); | |
| gfar_write(®s->fifo_tx_starve, priv->fifo_starve); | |
| gfar_write(®s->fifo_tx_starve_shutoff, priv->fifo_starve_off); | |
| } | |
| static struct net_device_stats *gfar_get_stats(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| unsigned long rx_packets = 0, rx_bytes = 0, rx_dropped = 0; | |
| unsigned long tx_packets = 0, tx_bytes = 0; | |
| int i = 0; | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| rx_packets += priv->rx_queue[i]->stats.rx_packets; | |
| rx_bytes += priv->rx_queue[i]->stats.rx_bytes; | |
| rx_dropped += priv->rx_queue[i]->stats.rx_dropped; | |
| } | |
| dev->stats.rx_packets = rx_packets; | |
| dev->stats.rx_bytes = rx_bytes; | |
| dev->stats.rx_dropped = rx_dropped; | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| tx_bytes += priv->tx_queue[i]->stats.tx_bytes; | |
| tx_packets += priv->tx_queue[i]->stats.tx_packets; | |
| } | |
| dev->stats.tx_bytes = tx_bytes; | |
| dev->stats.tx_packets = tx_packets; | |
| return &dev->stats; | |
| } | |
| static const struct net_device_ops gfar_netdev_ops = { | |
| .ndo_open = gfar_enet_open, | |
| .ndo_start_xmit = gfar_start_xmit, | |
| .ndo_stop = gfar_close, | |
| .ndo_change_mtu = gfar_change_mtu, | |
| .ndo_set_features = gfar_set_features, | |
| .ndo_set_multicast_list = gfar_set_multi, | |
| .ndo_tx_timeout = gfar_timeout, | |
| .ndo_do_ioctl = gfar_ioctl, | |
| .ndo_get_stats = gfar_get_stats, | |
| .ndo_vlan_rx_register = gfar_vlan_rx_register, | |
| .ndo_set_mac_address = eth_mac_addr, | |
| .ndo_validate_addr = eth_validate_addr, | |
| #ifdef CONFIG_NET_POLL_CONTROLLER | |
| .ndo_poll_controller = gfar_netpoll, | |
| #endif | |
| }; | |
| void lock_rx_qs(struct gfar_private *priv) | |
| { | |
| int i = 0x0; | |
| for (i = 0; i < priv->num_rx_queues; i++) | |
| spin_lock(&priv->rx_queue[i]->rxlock); | |
| } | |
| void lock_tx_qs(struct gfar_private *priv) | |
| { | |
| int i = 0x0; | |
| for (i = 0; i < priv->num_tx_queues; i++) | |
| spin_lock(&priv->tx_queue[i]->txlock); | |
| } | |
| void unlock_rx_qs(struct gfar_private *priv) | |
| { | |
| int i = 0x0; | |
| for (i = 0; i < priv->num_rx_queues; i++) | |
| spin_unlock(&priv->rx_queue[i]->rxlock); | |
| } | |
| void unlock_tx_qs(struct gfar_private *priv) | |
| { | |
| int i = 0x0; | |
| for (i = 0; i < priv->num_tx_queues; i++) | |
| spin_unlock(&priv->tx_queue[i]->txlock); | |
| } | |
| /* Returns 1 if incoming frames use an FCB */ | |
| static inline int gfar_uses_fcb(struct gfar_private *priv) | |
| { | |
| return priv->vlgrp || (priv->ndev->features & NETIF_F_RXCSUM) || | |
| (priv->device_flags & FSL_GIANFAR_DEV_HAS_TIMER); | |
| } | |
| static void free_tx_pointers(struct gfar_private *priv) | |
| { | |
| int i = 0; | |
| for (i = 0; i < priv->num_tx_queues; i++) | |
| kfree(priv->tx_queue[i]); | |
| } | |
| static void free_rx_pointers(struct gfar_private *priv) | |
| { | |
| int i = 0; | |
| for (i = 0; i < priv->num_rx_queues; i++) | |
| kfree(priv->rx_queue[i]); | |
| } | |
| static void unmap_group_regs(struct gfar_private *priv) | |
| { | |
| int i = 0; | |
| for (i = 0; i < MAXGROUPS; i++) | |
| if (priv->gfargrp[i].regs) | |
| iounmap(priv->gfargrp[i].regs); | |
| } | |
| static void disable_napi(struct gfar_private *priv) | |
| { | |
| int i = 0; | |
| for (i = 0; i < priv->num_grps; i++) | |
| napi_disable(&priv->gfargrp[i].napi); | |
| } | |
| static void enable_napi(struct gfar_private *priv) | |
| { | |
| int i = 0; | |
| for (i = 0; i < priv->num_grps; i++) | |
| napi_enable(&priv->gfargrp[i].napi); | |
| } | |
| static int gfar_parse_group(struct device_node *np, | |
| struct gfar_private *priv, const char *model) | |
| { | |
| u32 *queue_mask; | |
| priv->gfargrp[priv->num_grps].regs = of_iomap(np, 0); | |
| if (!priv->gfargrp[priv->num_grps].regs) | |
| return -ENOMEM; | |
| priv->gfargrp[priv->num_grps].interruptTransmit = | |
| irq_of_parse_and_map(np, 0); | |
| /* If we aren't the FEC we have multiple interrupts */ | |
| if (model && strcasecmp(model, "FEC")) { | |
| priv->gfargrp[priv->num_grps].interruptReceive = | |
| irq_of_parse_and_map(np, 1); | |
| priv->gfargrp[priv->num_grps].interruptError = | |
| irq_of_parse_and_map(np,2); | |
| if (priv->gfargrp[priv->num_grps].interruptTransmit == NO_IRQ || | |
| priv->gfargrp[priv->num_grps].interruptReceive == NO_IRQ || | |
| priv->gfargrp[priv->num_grps].interruptError == NO_IRQ) | |
| return -EINVAL; | |
| } | |
| priv->gfargrp[priv->num_grps].grp_id = priv->num_grps; | |
| priv->gfargrp[priv->num_grps].priv = priv; | |
| spin_lock_init(&priv->gfargrp[priv->num_grps].grplock); | |
| if(priv->mode == MQ_MG_MODE) { | |
| queue_mask = (u32 *)of_get_property(np, | |
| "fsl,rx-bit-map", NULL); | |
| priv->gfargrp[priv->num_grps].rx_bit_map = | |
| queue_mask ? *queue_mask :(DEFAULT_MAPPING >> priv->num_grps); | |
| queue_mask = (u32 *)of_get_property(np, | |
| "fsl,tx-bit-map", NULL); | |
| priv->gfargrp[priv->num_grps].tx_bit_map = | |
| queue_mask ? *queue_mask : (DEFAULT_MAPPING >> priv->num_grps); | |
| } else { | |
| priv->gfargrp[priv->num_grps].rx_bit_map = 0xFF; | |
| priv->gfargrp[priv->num_grps].tx_bit_map = 0xFF; | |
| } | |
| priv->num_grps++; | |
| return 0; | |
| } | |
| static int gfar_of_init(struct platform_device *ofdev, struct net_device **pdev) | |
| { | |
| const char *model; | |
| const char *ctype; | |
| const void *mac_addr; | |
| int err = 0, i; | |
| struct net_device *dev = NULL; | |
| struct gfar_private *priv = NULL; | |
| struct device_node *np = ofdev->dev.of_node; | |
| struct device_node *child = NULL; | |
| const u32 *stash; | |
| const u32 *stash_len; | |
| const u32 *stash_idx; | |
| unsigned int num_tx_qs, num_rx_qs; | |
| u32 *tx_queues, *rx_queues; | |
| if (!np || !of_device_is_available(np)) | |
| return -ENODEV; | |
| /* parse the num of tx and rx queues */ | |
| tx_queues = (u32 *)of_get_property(np, "fsl,num_tx_queues", NULL); | |
| num_tx_qs = tx_queues ? *tx_queues : 1; | |
| if (num_tx_qs > MAX_TX_QS) { | |
| printk(KERN_ERR "num_tx_qs(=%d) greater than MAX_TX_QS(=%d)\n", | |
| num_tx_qs, MAX_TX_QS); | |
| printk(KERN_ERR "Cannot do alloc_etherdev, aborting\n"); | |
| return -EINVAL; | |
| } | |
| rx_queues = (u32 *)of_get_property(np, "fsl,num_rx_queues", NULL); | |
| num_rx_qs = rx_queues ? *rx_queues : 1; | |
| if (num_rx_qs > MAX_RX_QS) { | |
| printk(KERN_ERR "num_rx_qs(=%d) greater than MAX_RX_QS(=%d)\n", | |
| num_tx_qs, MAX_TX_QS); | |
| printk(KERN_ERR "Cannot do alloc_etherdev, aborting\n"); | |
| return -EINVAL; | |
| } | |
| *pdev = alloc_etherdev_mq(sizeof(*priv), num_tx_qs); | |
| dev = *pdev; | |
| if (NULL == dev) | |
| return -ENOMEM; | |
| priv = netdev_priv(dev); | |
| priv->node = ofdev->dev.of_node; | |
| priv->ndev = dev; | |
| priv->num_tx_queues = num_tx_qs; | |
| netif_set_real_num_rx_queues(dev, num_rx_qs); | |
| priv->num_rx_queues = num_rx_qs; | |
| priv->num_grps = 0x0; | |
| model = of_get_property(np, "model", NULL); | |
| for (i = 0; i < MAXGROUPS; i++) | |
| priv->gfargrp[i].regs = NULL; | |
| /* Parse and initialize group specific information */ | |
| if (of_device_is_compatible(np, "fsl,etsec2")) { | |
| priv->mode = MQ_MG_MODE; | |
| for_each_child_of_node(np, child) { | |
| err = gfar_parse_group(child, priv, model); | |
| if (err) | |
| goto err_grp_init; | |
| } | |
| } else { | |
| priv->mode = SQ_SG_MODE; | |
| err = gfar_parse_group(np, priv, model); | |
| if(err) | |
| goto err_grp_init; | |
| } | |
| for (i = 0; i < priv->num_tx_queues; i++) | |
| priv->tx_queue[i] = NULL; | |
| for (i = 0; i < priv->num_rx_queues; i++) | |
| priv->rx_queue[i] = NULL; | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| priv->tx_queue[i] = kzalloc(sizeof(struct gfar_priv_tx_q), | |
| GFP_KERNEL); | |
| if (!priv->tx_queue[i]) { | |
| err = -ENOMEM; | |
| goto tx_alloc_failed; | |
| } | |
| priv->tx_queue[i]->tx_skbuff = NULL; | |
| priv->tx_queue[i]->qindex = i; | |
| priv->tx_queue[i]->dev = dev; | |
| spin_lock_init(&(priv->tx_queue[i]->txlock)); | |
| } | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| priv->rx_queue[i] = kzalloc(sizeof(struct gfar_priv_rx_q), | |
| GFP_KERNEL); | |
| if (!priv->rx_queue[i]) { | |
| err = -ENOMEM; | |
| goto rx_alloc_failed; | |
| } | |
| priv->rx_queue[i]->rx_skbuff = NULL; | |
| priv->rx_queue[i]->qindex = i; | |
| priv->rx_queue[i]->dev = dev; | |
| spin_lock_init(&(priv->rx_queue[i]->rxlock)); | |
| } | |
| stash = of_get_property(np, "bd-stash", NULL); | |
| if (stash) { | |
| priv->device_flags |= FSL_GIANFAR_DEV_HAS_BD_STASHING; | |
| priv->bd_stash_en = 1; | |
| } | |
| stash_len = of_get_property(np, "rx-stash-len", NULL); | |
| if (stash_len) | |
| priv->rx_stash_size = *stash_len; | |
| stash_idx = of_get_property(np, "rx-stash-idx", NULL); | |
| if (stash_idx) | |
| priv->rx_stash_index = *stash_idx; | |
| if (stash_len || stash_idx) | |
| priv->device_flags |= FSL_GIANFAR_DEV_HAS_BUF_STASHING; | |
| mac_addr = of_get_mac_address(np); | |
| if (mac_addr) | |
| memcpy(dev->dev_addr, mac_addr, MAC_ADDR_LEN); | |
| if (model && !strcasecmp(model, "TSEC")) | |
| priv->device_flags = | |
| FSL_GIANFAR_DEV_HAS_GIGABIT | | |
| FSL_GIANFAR_DEV_HAS_COALESCE | | |
| FSL_GIANFAR_DEV_HAS_RMON | | |
| FSL_GIANFAR_DEV_HAS_MULTI_INTR; | |
| if (model && !strcasecmp(model, "eTSEC")) | |
| priv->device_flags = | |
| FSL_GIANFAR_DEV_HAS_GIGABIT | | |
| FSL_GIANFAR_DEV_HAS_COALESCE | | |
| FSL_GIANFAR_DEV_HAS_RMON | | |
| FSL_GIANFAR_DEV_HAS_MULTI_INTR | | |
| FSL_GIANFAR_DEV_HAS_PADDING | | |
| FSL_GIANFAR_DEV_HAS_CSUM | | |
| FSL_GIANFAR_DEV_HAS_VLAN | | |
| FSL_GIANFAR_DEV_HAS_MAGIC_PACKET | | |
| FSL_GIANFAR_DEV_HAS_EXTENDED_HASH | | |
| FSL_GIANFAR_DEV_HAS_TIMER; | |
| ctype = of_get_property(np, "phy-connection-type", NULL); | |
| /* We only care about rgmii-id. The rest are autodetected */ | |
| if (ctype && !strcmp(ctype, "rgmii-id")) | |
| priv->interface = PHY_INTERFACE_MODE_RGMII_ID; | |
| else | |
| priv->interface = PHY_INTERFACE_MODE_MII; | |
| if (of_get_property(np, "fsl,magic-packet", NULL)) | |
| priv->device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET; | |
| priv->phy_node = of_parse_phandle(np, "phy-handle", 0); | |
| /* Find the TBI PHY. If it's not there, we don't support SGMII */ | |
| priv->tbi_node = of_parse_phandle(np, "tbi-handle", 0); | |
| return 0; | |
| rx_alloc_failed: | |
| free_rx_pointers(priv); | |
| tx_alloc_failed: | |
| free_tx_pointers(priv); | |
| err_grp_init: | |
| unmap_group_regs(priv); | |
| free_netdev(dev); | |
| return err; | |
| } | |
| static int gfar_hwtstamp_ioctl(struct net_device *netdev, | |
| struct ifreq *ifr, int cmd) | |
| { | |
| struct hwtstamp_config config; | |
| struct gfar_private *priv = netdev_priv(netdev); | |
| if (copy_from_user(&config, ifr->ifr_data, sizeof(config))) | |
| return -EFAULT; | |
| /* reserved for future extensions */ | |
| if (config.flags) | |
| return -EINVAL; | |
| switch (config.tx_type) { | |
| case HWTSTAMP_TX_OFF: | |
| priv->hwts_tx_en = 0; | |
| break; | |
| case HWTSTAMP_TX_ON: | |
| if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_TIMER)) | |
| return -ERANGE; | |
| priv->hwts_tx_en = 1; | |
| break; | |
| default: | |
| return -ERANGE; | |
| } | |
| switch (config.rx_filter) { | |
| case HWTSTAMP_FILTER_NONE: | |
| if (priv->hwts_rx_en) { | |
| stop_gfar(netdev); | |
| priv->hwts_rx_en = 0; | |
| startup_gfar(netdev); | |
| } | |
| break; | |
| default: | |
| if (!(priv->device_flags & FSL_GIANFAR_DEV_HAS_TIMER)) | |
| return -ERANGE; | |
| if (!priv->hwts_rx_en) { | |
| stop_gfar(netdev); | |
| priv->hwts_rx_en = 1; | |
| startup_gfar(netdev); | |
| } | |
| config.rx_filter = HWTSTAMP_FILTER_ALL; | |
| break; | |
| } | |
| return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ? | |
| -EFAULT : 0; | |
| } | |
| /* Ioctl MII Interface */ | |
| static int gfar_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| if (!netif_running(dev)) | |
| return -EINVAL; | |
| if (cmd == SIOCSHWTSTAMP) | |
| return gfar_hwtstamp_ioctl(dev, rq, cmd); | |
| if (!priv->phydev) | |
| return -ENODEV; | |
| return phy_mii_ioctl(priv->phydev, rq, cmd); | |
| } | |
| static unsigned int reverse_bitmap(unsigned int bit_map, unsigned int max_qs) | |
| { | |
| unsigned int new_bit_map = 0x0; | |
| int mask = 0x1 << (max_qs - 1), i; | |
| for (i = 0; i < max_qs; i++) { | |
| if (bit_map & mask) | |
| new_bit_map = new_bit_map + (1 << i); | |
| mask = mask >> 0x1; | |
| } | |
| return new_bit_map; | |
| } | |
| static u32 cluster_entry_per_class(struct gfar_private *priv, u32 rqfar, | |
| u32 class) | |
| { | |
| u32 rqfpr = FPR_FILER_MASK; | |
| u32 rqfcr = 0x0; | |
| rqfar--; | |
| rqfcr = RQFCR_CLE | RQFCR_PID_MASK | RQFCR_CMP_EXACT; | |
| priv->ftp_rqfpr[rqfar] = rqfpr; | |
| priv->ftp_rqfcr[rqfar] = rqfcr; | |
| gfar_write_filer(priv, rqfar, rqfcr, rqfpr); | |
| rqfar--; | |
| rqfcr = RQFCR_CMP_NOMATCH; | |
| priv->ftp_rqfpr[rqfar] = rqfpr; | |
| priv->ftp_rqfcr[rqfar] = rqfcr; | |
| gfar_write_filer(priv, rqfar, rqfcr, rqfpr); | |
| rqfar--; | |
| rqfcr = RQFCR_CMP_EXACT | RQFCR_PID_PARSE | RQFCR_CLE | RQFCR_AND; | |
| rqfpr = class; | |
| priv->ftp_rqfcr[rqfar] = rqfcr; | |
| priv->ftp_rqfpr[rqfar] = rqfpr; | |
| gfar_write_filer(priv, rqfar, rqfcr, rqfpr); | |
| rqfar--; | |
| rqfcr = RQFCR_CMP_EXACT | RQFCR_PID_MASK | RQFCR_AND; | |
| rqfpr = class; | |
| priv->ftp_rqfcr[rqfar] = rqfcr; | |
| priv->ftp_rqfpr[rqfar] = rqfpr; | |
| gfar_write_filer(priv, rqfar, rqfcr, rqfpr); | |
| return rqfar; | |
| } | |
| static void gfar_init_filer_table(struct gfar_private *priv) | |
| { | |
| int i = 0x0; | |
| u32 rqfar = MAX_FILER_IDX; | |
| u32 rqfcr = 0x0; | |
| u32 rqfpr = FPR_FILER_MASK; | |
| /* Default rule */ | |
| rqfcr = RQFCR_CMP_MATCH; | |
| priv->ftp_rqfcr[rqfar] = rqfcr; | |
| priv->ftp_rqfpr[rqfar] = rqfpr; | |
| gfar_write_filer(priv, rqfar, rqfcr, rqfpr); | |
| rqfar = cluster_entry_per_class(priv, rqfar, RQFPR_IPV6); | |
| rqfar = cluster_entry_per_class(priv, rqfar, RQFPR_IPV6 | RQFPR_UDP); | |
| rqfar = cluster_entry_per_class(priv, rqfar, RQFPR_IPV6 | RQFPR_TCP); | |
| rqfar = cluster_entry_per_class(priv, rqfar, RQFPR_IPV4); | |
| rqfar = cluster_entry_per_class(priv, rqfar, RQFPR_IPV4 | RQFPR_UDP); | |
| rqfar = cluster_entry_per_class(priv, rqfar, RQFPR_IPV4 | RQFPR_TCP); | |
| /* cur_filer_idx indicated the first non-masked rule */ | |
| priv->cur_filer_idx = rqfar; | |
| /* Rest are masked rules */ | |
| rqfcr = RQFCR_CMP_NOMATCH; | |
| for (i = 0; i < rqfar; i++) { | |
| priv->ftp_rqfcr[i] = rqfcr; | |
| priv->ftp_rqfpr[i] = rqfpr; | |
| gfar_write_filer(priv, i, rqfcr, rqfpr); | |
| } | |
| } | |
| static void gfar_detect_errata(struct gfar_private *priv) | |
| { | |
| struct device *dev = &priv->ofdev->dev; | |
| unsigned int pvr = mfspr(SPRN_PVR); | |
| unsigned int svr = mfspr(SPRN_SVR); | |
| unsigned int mod = (svr >> 16) & 0xfff6; /* w/o E suffix */ | |
| unsigned int rev = svr & 0xffff; | |
| /* MPC8313 Rev 2.0 and higher; All MPC837x */ | |
| if ((pvr == 0x80850010 && mod == 0x80b0 && rev >= 0x0020) || | |
| (pvr == 0x80861010 && (mod & 0xfff9) == 0x80c0)) | |
| priv->errata |= GFAR_ERRATA_74; | |
| /* MPC8313 and MPC837x all rev */ | |
| if ((pvr == 0x80850010 && mod == 0x80b0) || | |
| (pvr == 0x80861010 && (mod & 0xfff9) == 0x80c0)) | |
| priv->errata |= GFAR_ERRATA_76; | |
| /* MPC8313 and MPC837x all rev */ | |
| if ((pvr == 0x80850010 && mod == 0x80b0) || | |
| (pvr == 0x80861010 && (mod & 0xfff9) == 0x80c0)) | |
| priv->errata |= GFAR_ERRATA_A002; | |
| /* MPC8313 Rev < 2.0, MPC8548 rev 2.0 */ | |
| if ((pvr == 0x80850010 && mod == 0x80b0 && rev < 0x0020) || | |
| (pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020)) | |
| priv->errata |= GFAR_ERRATA_12; | |
| if (priv->errata) | |
| dev_info(dev, "enabled errata workarounds, flags: 0x%x\n", | |
| priv->errata); | |
| } | |
| /* Set up the ethernet device structure, private data, | |
| * and anything else we need before we start */ | |
| static int gfar_probe(struct platform_device *ofdev) | |
| { | |
| u32 tempval; | |
| struct net_device *dev = NULL; | |
| struct gfar_private *priv = NULL; | |
| struct gfar __iomem *regs = NULL; | |
| int err = 0, i, grp_idx = 0; | |
| int len_devname; | |
| u32 rstat = 0, tstat = 0, rqueue = 0, tqueue = 0; | |
| u32 isrg = 0; | |
| u32 __iomem *baddr; | |
| err = gfar_of_init(ofdev, &dev); | |
| if (err) | |
| return err; | |
| priv = netdev_priv(dev); | |
| priv->ndev = dev; | |
| priv->ofdev = ofdev; | |
| priv->node = ofdev->dev.of_node; | |
| SET_NETDEV_DEV(dev, &ofdev->dev); | |
| spin_lock_init(&priv->bflock); | |
| INIT_WORK(&priv->reset_task, gfar_reset_task); | |
| dev_set_drvdata(&ofdev->dev, priv); | |
| regs = priv->gfargrp[0].regs; | |
| gfar_detect_errata(priv); | |
| /* Stop the DMA engine now, in case it was running before */ | |
| /* (The firmware could have used it, and left it running). */ | |
| gfar_halt(dev); | |
| /* Reset MAC layer */ | |
| gfar_write(®s->maccfg1, MACCFG1_SOFT_RESET); | |
| /* We need to delay at least 3 TX clocks */ | |
| udelay(2); | |
| tempval = (MACCFG1_TX_FLOW | MACCFG1_RX_FLOW); | |
| gfar_write(®s->maccfg1, tempval); | |
| /* Initialize MACCFG2. */ | |
| tempval = MACCFG2_INIT_SETTINGS; | |
| if (gfar_has_errata(priv, GFAR_ERRATA_74)) | |
| tempval |= MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK; | |
| gfar_write(®s->maccfg2, tempval); | |
| /* Initialize ECNTRL */ | |
| gfar_write(®s->ecntrl, ECNTRL_INIT_SETTINGS); | |
| /* Set the dev->base_addr to the gfar reg region */ | |
| dev->base_addr = (unsigned long) regs; | |
| SET_NETDEV_DEV(dev, &ofdev->dev); | |
| /* Fill in the dev structure */ | |
| dev->watchdog_timeo = TX_TIMEOUT; | |
| dev->mtu = 1500; | |
| dev->netdev_ops = &gfar_netdev_ops; | |
| dev->ethtool_ops = &gfar_ethtool_ops; | |
| /* Register for napi ...We are registering NAPI for each grp */ | |
| for (i = 0; i < priv->num_grps; i++) | |
| netif_napi_add(dev, &priv->gfargrp[i].napi, gfar_poll, GFAR_DEV_WEIGHT); | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_CSUM) { | |
| dev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG | | |
| NETIF_F_RXCSUM; | |
| dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG | | |
| NETIF_F_RXCSUM | NETIF_F_HIGHDMA; | |
| } | |
| priv->vlgrp = NULL; | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_VLAN) | |
| dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_EXTENDED_HASH) { | |
| priv->extended_hash = 1; | |
| priv->hash_width = 9; | |
| priv->hash_regs[0] = ®s->igaddr0; | |
| priv->hash_regs[1] = ®s->igaddr1; | |
| priv->hash_regs[2] = ®s->igaddr2; | |
| priv->hash_regs[3] = ®s->igaddr3; | |
| priv->hash_regs[4] = ®s->igaddr4; | |
| priv->hash_regs[5] = ®s->igaddr5; | |
| priv->hash_regs[6] = ®s->igaddr6; | |
| priv->hash_regs[7] = ®s->igaddr7; | |
| priv->hash_regs[8] = ®s->gaddr0; | |
| priv->hash_regs[9] = ®s->gaddr1; | |
| priv->hash_regs[10] = ®s->gaddr2; | |
| priv->hash_regs[11] = ®s->gaddr3; | |
| priv->hash_regs[12] = ®s->gaddr4; | |
| priv->hash_regs[13] = ®s->gaddr5; | |
| priv->hash_regs[14] = ®s->gaddr6; | |
| priv->hash_regs[15] = ®s->gaddr7; | |
| } else { | |
| priv->extended_hash = 0; | |
| priv->hash_width = 8; | |
| priv->hash_regs[0] = ®s->gaddr0; | |
| priv->hash_regs[1] = ®s->gaddr1; | |
| priv->hash_regs[2] = ®s->gaddr2; | |
| priv->hash_regs[3] = ®s->gaddr3; | |
| priv->hash_regs[4] = ®s->gaddr4; | |
| priv->hash_regs[5] = ®s->gaddr5; | |
| priv->hash_regs[6] = ®s->gaddr6; | |
| priv->hash_regs[7] = ®s->gaddr7; | |
| } | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_PADDING) | |
| priv->padding = DEFAULT_PADDING; | |
| else | |
| priv->padding = 0; | |
| if (dev->features & NETIF_F_IP_CSUM || | |
| priv->device_flags & FSL_GIANFAR_DEV_HAS_TIMER) | |
| dev->hard_header_len += GMAC_FCB_LEN; | |
| /* Program the isrg regs only if number of grps > 1 */ | |
| if (priv->num_grps > 1) { | |
| baddr = ®s->isrg0; | |
| for (i = 0; i < priv->num_grps; i++) { | |
| isrg |= (priv->gfargrp[i].rx_bit_map << ISRG_SHIFT_RX); | |
| isrg |= (priv->gfargrp[i].tx_bit_map << ISRG_SHIFT_TX); | |
| gfar_write(baddr, isrg); | |
| baddr++; | |
| isrg = 0x0; | |
| } | |
| } | |
| /* Need to reverse the bit maps as bit_map's MSB is q0 | |
| * but, for_each_set_bit parses from right to left, which | |
| * basically reverses the queue numbers */ | |
| for (i = 0; i< priv->num_grps; i++) { | |
| priv->gfargrp[i].tx_bit_map = reverse_bitmap( | |
| priv->gfargrp[i].tx_bit_map, MAX_TX_QS); | |
| priv->gfargrp[i].rx_bit_map = reverse_bitmap( | |
| priv->gfargrp[i].rx_bit_map, MAX_RX_QS); | |
| } | |
| /* Calculate RSTAT, TSTAT, RQUEUE and TQUEUE values, | |
| * also assign queues to groups */ | |
| for (grp_idx = 0; grp_idx < priv->num_grps; grp_idx++) { | |
| priv->gfargrp[grp_idx].num_rx_queues = 0x0; | |
| for_each_set_bit(i, &priv->gfargrp[grp_idx].rx_bit_map, | |
| priv->num_rx_queues) { | |
| priv->gfargrp[grp_idx].num_rx_queues++; | |
| priv->rx_queue[i]->grp = &priv->gfargrp[grp_idx]; | |
| rstat = rstat | (RSTAT_CLEAR_RHALT >> i); | |
| rqueue = rqueue | ((RQUEUE_EN0 | RQUEUE_EX0) >> i); | |
| } | |
| priv->gfargrp[grp_idx].num_tx_queues = 0x0; | |
| for_each_set_bit(i, &priv->gfargrp[grp_idx].tx_bit_map, | |
| priv->num_tx_queues) { | |
| priv->gfargrp[grp_idx].num_tx_queues++; | |
| priv->tx_queue[i]->grp = &priv->gfargrp[grp_idx]; | |
| tstat = tstat | (TSTAT_CLEAR_THALT >> i); | |
| tqueue = tqueue | (TQUEUE_EN0 >> i); | |
| } | |
| priv->gfargrp[grp_idx].rstat = rstat; | |
| priv->gfargrp[grp_idx].tstat = tstat; | |
| rstat = tstat =0; | |
| } | |
| gfar_write(®s->rqueue, rqueue); | |
| gfar_write(®s->tqueue, tqueue); | |
| priv->rx_buffer_size = DEFAULT_RX_BUFFER_SIZE; | |
| /* Initializing some of the rx/tx queue level parameters */ | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| priv->tx_queue[i]->tx_ring_size = DEFAULT_TX_RING_SIZE; | |
| priv->tx_queue[i]->num_txbdfree = DEFAULT_TX_RING_SIZE; | |
| priv->tx_queue[i]->txcoalescing = DEFAULT_TX_COALESCE; | |
| priv->tx_queue[i]->txic = DEFAULT_TXIC; | |
| } | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| priv->rx_queue[i]->rx_ring_size = DEFAULT_RX_RING_SIZE; | |
| priv->rx_queue[i]->rxcoalescing = DEFAULT_RX_COALESCE; | |
| priv->rx_queue[i]->rxic = DEFAULT_RXIC; | |
| } | |
| /* enable filer if using multiple RX queues*/ | |
| if(priv->num_rx_queues > 1) | |
| priv->rx_filer_enable = 1; | |
| /* Enable most messages by default */ | |
| priv->msg_enable = (NETIF_MSG_IFUP << 1 ) - 1; | |
| /* Carrier starts down, phylib will bring it up */ | |
| netif_carrier_off(dev); | |
| err = register_netdev(dev); | |
| if (err) { | |
| printk(KERN_ERR "%s: Cannot register net device, aborting.\n", | |
| dev->name); | |
| goto register_fail; | |
| } | |
| device_init_wakeup(&dev->dev, | |
| priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET); | |
| /* fill out IRQ number and name fields */ | |
| len_devname = strlen(dev->name); | |
| for (i = 0; i < priv->num_grps; i++) { | |
| strncpy(&priv->gfargrp[i].int_name_tx[0], dev->name, | |
| len_devname); | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { | |
| strncpy(&priv->gfargrp[i].int_name_tx[len_devname], | |
| "_g", sizeof("_g")); | |
| priv->gfargrp[i].int_name_tx[ | |
| strlen(priv->gfargrp[i].int_name_tx)] = i+48; | |
| strncpy(&priv->gfargrp[i].int_name_tx[strlen( | |
| priv->gfargrp[i].int_name_tx)], | |
| "_tx", sizeof("_tx") + 1); | |
| strncpy(&priv->gfargrp[i].int_name_rx[0], dev->name, | |
| len_devname); | |
| strncpy(&priv->gfargrp[i].int_name_rx[len_devname], | |
| "_g", sizeof("_g")); | |
| priv->gfargrp[i].int_name_rx[ | |
| strlen(priv->gfargrp[i].int_name_rx)] = i+48; | |
| strncpy(&priv->gfargrp[i].int_name_rx[strlen( | |
| priv->gfargrp[i].int_name_rx)], | |
| "_rx", sizeof("_rx") + 1); | |
| strncpy(&priv->gfargrp[i].int_name_er[0], dev->name, | |
| len_devname); | |
| strncpy(&priv->gfargrp[i].int_name_er[len_devname], | |
| "_g", sizeof("_g")); | |
| priv->gfargrp[i].int_name_er[strlen( | |
| priv->gfargrp[i].int_name_er)] = i+48; | |
| strncpy(&priv->gfargrp[i].int_name_er[strlen(\ | |
| priv->gfargrp[i].int_name_er)], | |
| "_er", sizeof("_er") + 1); | |
| } else | |
| priv->gfargrp[i].int_name_tx[len_devname] = '\0'; | |
| } | |
| /* Initialize the filer table */ | |
| gfar_init_filer_table(priv); | |
| /* Create all the sysfs files */ | |
| gfar_init_sysfs(dev); | |
| /* Print out the device info */ | |
| printk(KERN_INFO DEVICE_NAME "%pM\n", dev->name, dev->dev_addr); | |
| /* Even more device info helps when determining which kernel */ | |
| /* provided which set of benchmarks. */ | |
| printk(KERN_INFO "%s: Running with NAPI enabled\n", dev->name); | |
| for (i = 0; i < priv->num_rx_queues; i++) | |
| printk(KERN_INFO "%s: RX BD ring size for Q[%d]: %d\n", | |
| dev->name, i, priv->rx_queue[i]->rx_ring_size); | |
| for(i = 0; i < priv->num_tx_queues; i++) | |
| printk(KERN_INFO "%s: TX BD ring size for Q[%d]: %d\n", | |
| dev->name, i, priv->tx_queue[i]->tx_ring_size); | |
| return 0; | |
| register_fail: | |
| unmap_group_regs(priv); | |
| free_tx_pointers(priv); | |
| free_rx_pointers(priv); | |
| if (priv->phy_node) | |
| of_node_put(priv->phy_node); | |
| if (priv->tbi_node) | |
| of_node_put(priv->tbi_node); | |
| free_netdev(dev); | |
| return err; | |
| } | |
| static int gfar_remove(struct platform_device *ofdev) | |
| { | |
| struct gfar_private *priv = dev_get_drvdata(&ofdev->dev); | |
| if (priv->phy_node) | |
| of_node_put(priv->phy_node); | |
| if (priv->tbi_node) | |
| of_node_put(priv->tbi_node); | |
| dev_set_drvdata(&ofdev->dev, NULL); | |
| unregister_netdev(priv->ndev); | |
| unmap_group_regs(priv); | |
| free_netdev(priv->ndev); | |
| return 0; | |
| } | |
| #ifdef CONFIG_PM | |
| static int gfar_suspend(struct device *dev) | |
| { | |
| struct gfar_private *priv = dev_get_drvdata(dev); | |
| struct net_device *ndev = priv->ndev; | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| unsigned long flags; | |
| u32 tempval; | |
| int magic_packet = priv->wol_en && | |
| (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET); | |
| netif_device_detach(ndev); | |
| if (netif_running(ndev)) { | |
| local_irq_save(flags); | |
| lock_tx_qs(priv); | |
| lock_rx_qs(priv); | |
| gfar_halt_nodisable(ndev); | |
| /* Disable Tx, and Rx if wake-on-LAN is disabled. */ | |
| tempval = gfar_read(®s->maccfg1); | |
| tempval &= ~MACCFG1_TX_EN; | |
| if (!magic_packet) | |
| tempval &= ~MACCFG1_RX_EN; | |
| gfar_write(®s->maccfg1, tempval); | |
| unlock_rx_qs(priv); | |
| unlock_tx_qs(priv); | |
| local_irq_restore(flags); | |
| disable_napi(priv); | |
| if (magic_packet) { | |
| /* Enable interrupt on Magic Packet */ | |
| gfar_write(®s->imask, IMASK_MAG); | |
| /* Enable Magic Packet mode */ | |
| tempval = gfar_read(®s->maccfg2); | |
| tempval |= MACCFG2_MPEN; | |
| gfar_write(®s->maccfg2, tempval); | |
| } else { | |
| phy_stop(priv->phydev); | |
| } | |
| } | |
| return 0; | |
| } | |
| static int gfar_resume(struct device *dev) | |
| { | |
| struct gfar_private *priv = dev_get_drvdata(dev); | |
| struct net_device *ndev = priv->ndev; | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| unsigned long flags; | |
| u32 tempval; | |
| int magic_packet = priv->wol_en && | |
| (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET); | |
| if (!netif_running(ndev)) { | |
| netif_device_attach(ndev); | |
| return 0; | |
| } | |
| if (!magic_packet && priv->phydev) | |
| phy_start(priv->phydev); | |
| /* Disable Magic Packet mode, in case something | |
| * else woke us up. | |
| */ | |
| local_irq_save(flags); | |
| lock_tx_qs(priv); | |
| lock_rx_qs(priv); | |
| tempval = gfar_read(®s->maccfg2); | |
| tempval &= ~MACCFG2_MPEN; | |
| gfar_write(®s->maccfg2, tempval); | |
| gfar_start(ndev); | |
| unlock_rx_qs(priv); | |
| unlock_tx_qs(priv); | |
| local_irq_restore(flags); | |
| netif_device_attach(ndev); | |
| enable_napi(priv); | |
| return 0; | |
| } | |
| static int gfar_restore(struct device *dev) | |
| { | |
| struct gfar_private *priv = dev_get_drvdata(dev); | |
| struct net_device *ndev = priv->ndev; | |
| if (!netif_running(ndev)) | |
| return 0; | |
| gfar_init_bds(ndev); | |
| init_registers(ndev); | |
| gfar_set_mac_address(ndev); | |
| gfar_init_mac(ndev); | |
| gfar_start(ndev); | |
| priv->oldlink = 0; | |
| priv->oldspeed = 0; | |
| priv->oldduplex = -1; | |
| if (priv->phydev) | |
| phy_start(priv->phydev); | |
| netif_device_attach(ndev); | |
| enable_napi(priv); | |
| return 0; | |
| } | |
| static struct dev_pm_ops gfar_pm_ops = { | |
| .suspend = gfar_suspend, | |
| .resume = gfar_resume, | |
| .freeze = gfar_suspend, | |
| .thaw = gfar_resume, | |
| .restore = gfar_restore, | |
| }; | |
| #define GFAR_PM_OPS (&gfar_pm_ops) | |
| #else | |
| #define GFAR_PM_OPS NULL | |
| #endif | |
| /* Reads the controller's registers to determine what interface | |
| * connects it to the PHY. | |
| */ | |
| static phy_interface_t gfar_get_interface(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 ecntrl; | |
| ecntrl = gfar_read(®s->ecntrl); | |
| if (ecntrl & ECNTRL_SGMII_MODE) | |
| return PHY_INTERFACE_MODE_SGMII; | |
| if (ecntrl & ECNTRL_TBI_MODE) { | |
| if (ecntrl & ECNTRL_REDUCED_MODE) | |
| return PHY_INTERFACE_MODE_RTBI; | |
| else | |
| return PHY_INTERFACE_MODE_TBI; | |
| } | |
| if (ecntrl & ECNTRL_REDUCED_MODE) { | |
| if (ecntrl & ECNTRL_REDUCED_MII_MODE) | |
| return PHY_INTERFACE_MODE_RMII; | |
| else { | |
| phy_interface_t interface = priv->interface; | |
| /* | |
| * This isn't autodetected right now, so it must | |
| * be set by the device tree or platform code. | |
| */ | |
| if (interface == PHY_INTERFACE_MODE_RGMII_ID) | |
| return PHY_INTERFACE_MODE_RGMII_ID; | |
| return PHY_INTERFACE_MODE_RGMII; | |
| } | |
| } | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT) | |
| return PHY_INTERFACE_MODE_GMII; | |
| return PHY_INTERFACE_MODE_MII; | |
| } | |
| /* Initializes driver's PHY state, and attaches to the PHY. | |
| * Returns 0 on success. | |
| */ | |
| static int init_phy(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| uint gigabit_support = | |
| priv->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ? | |
| SUPPORTED_1000baseT_Full : 0; | |
| phy_interface_t interface; | |
| priv->oldlink = 0; | |
| priv->oldspeed = 0; | |
| priv->oldduplex = -1; | |
| interface = gfar_get_interface(dev); | |
| priv->phydev = of_phy_connect(dev, priv->phy_node, &adjust_link, 0, | |
| interface); | |
| if (!priv->phydev) | |
| priv->phydev = of_phy_connect_fixed_link(dev, &adjust_link, | |
| interface); | |
| if (!priv->phydev) { | |
| dev_err(&dev->dev, "could not attach to PHY\n"); | |
| return -ENODEV; | |
| } | |
| if (interface == PHY_INTERFACE_MODE_SGMII) | |
| gfar_configure_serdes(dev); | |
| /* Remove any features not supported by the controller */ | |
| priv->phydev->supported &= (GFAR_SUPPORTED | gigabit_support); | |
| priv->phydev->advertising = priv->phydev->supported; | |
| return 0; | |
| } | |
| /* | |
| * Initialize TBI PHY interface for communicating with the | |
| * SERDES lynx PHY on the chip. We communicate with this PHY | |
| * through the MDIO bus on each controller, treating it as a | |
| * "normal" PHY at the address found in the TBIPA register. We assume | |
| * that the TBIPA register is valid. Either the MDIO bus code will set | |
| * it to a value that doesn't conflict with other PHYs on the bus, or the | |
| * value doesn't matter, as there are no other PHYs on the bus. | |
| */ | |
| static void gfar_configure_serdes(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct phy_device *tbiphy; | |
| if (!priv->tbi_node) { | |
| dev_warn(&dev->dev, "error: SGMII mode requires that the " | |
| "device tree specify a tbi-handle\n"); | |
| return; | |
| } | |
| tbiphy = of_phy_find_device(priv->tbi_node); | |
| if (!tbiphy) { | |
| dev_err(&dev->dev, "error: Could not get TBI device\n"); | |
| return; | |
| } | |
| /* | |
| * If the link is already up, we must already be ok, and don't need to | |
| * configure and reset the TBI<->SerDes link. Maybe U-Boot configured | |
| * everything for us? Resetting it takes the link down and requires | |
| * several seconds for it to come back. | |
| */ | |
| if (phy_read(tbiphy, MII_BMSR) & BMSR_LSTATUS) | |
| return; | |
| /* Single clk mode, mii mode off(for serdes communication) */ | |
| phy_write(tbiphy, MII_TBICON, TBICON_CLK_SELECT); | |
| phy_write(tbiphy, MII_ADVERTISE, | |
| ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE | | |
| ADVERTISE_1000XPSE_ASYM); | |
| phy_write(tbiphy, MII_BMCR, BMCR_ANENABLE | | |
| BMCR_ANRESTART | BMCR_FULLDPLX | BMCR_SPEED1000); | |
| } | |
| static void init_registers(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = NULL; | |
| int i = 0; | |
| for (i = 0; i < priv->num_grps; i++) { | |
| regs = priv->gfargrp[i].regs; | |
| /* Clear IEVENT */ | |
| gfar_write(®s->ievent, IEVENT_INIT_CLEAR); | |
| /* Initialize IMASK */ | |
| gfar_write(®s->imask, IMASK_INIT_CLEAR); | |
| } | |
| regs = priv->gfargrp[0].regs; | |
| /* Init hash registers to zero */ | |
| gfar_write(®s->igaddr0, 0); | |
| gfar_write(®s->igaddr1, 0); | |
| gfar_write(®s->igaddr2, 0); | |
| gfar_write(®s->igaddr3, 0); | |
| gfar_write(®s->igaddr4, 0); | |
| gfar_write(®s->igaddr5, 0); | |
| gfar_write(®s->igaddr6, 0); | |
| gfar_write(®s->igaddr7, 0); | |
| gfar_write(®s->gaddr0, 0); | |
| gfar_write(®s->gaddr1, 0); | |
| gfar_write(®s->gaddr2, 0); | |
| gfar_write(®s->gaddr3, 0); | |
| gfar_write(®s->gaddr4, 0); | |
| gfar_write(®s->gaddr5, 0); | |
| gfar_write(®s->gaddr6, 0); | |
| gfar_write(®s->gaddr7, 0); | |
| /* Zero out the rmon mib registers if it has them */ | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_RMON) { | |
| memset_io(&(regs->rmon), 0, sizeof (struct rmon_mib)); | |
| /* Mask off the CAM interrupts */ | |
| gfar_write(®s->rmon.cam1, 0xffffffff); | |
| gfar_write(®s->rmon.cam2, 0xffffffff); | |
| } | |
| /* Initialize the max receive buffer length */ | |
| gfar_write(®s->mrblr, priv->rx_buffer_size); | |
| /* Initialize the Minimum Frame Length Register */ | |
| gfar_write(®s->minflr, MINFLR_INIT_SETTINGS); | |
| } | |
| static int __gfar_is_rx_idle(struct gfar_private *priv) | |
| { | |
| u32 res; | |
| /* | |
| * Normaly TSEC should not hang on GRS commands, so we should | |
| * actually wait for IEVENT_GRSC flag. | |
| */ | |
| if (likely(!gfar_has_errata(priv, GFAR_ERRATA_A002))) | |
| return 0; | |
| /* | |
| * Read the eTSEC register at offset 0xD1C. If bits 7-14 are | |
| * the same as bits 23-30, the eTSEC Rx is assumed to be idle | |
| * and the Rx can be safely reset. | |
| */ | |
| res = gfar_read((void __iomem *)priv->gfargrp[0].regs + 0xd1c); | |
| res &= 0x7f807f80; | |
| if ((res & 0xffff) == (res >> 16)) | |
| return 1; | |
| return 0; | |
| } | |
| /* Halt the receive and transmit queues */ | |
| static void gfar_halt_nodisable(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = NULL; | |
| u32 tempval; | |
| int i = 0; | |
| for (i = 0; i < priv->num_grps; i++) { | |
| regs = priv->gfargrp[i].regs; | |
| /* Mask all interrupts */ | |
| gfar_write(®s->imask, IMASK_INIT_CLEAR); | |
| /* Clear all interrupts */ | |
| gfar_write(®s->ievent, IEVENT_INIT_CLEAR); | |
| } | |
| regs = priv->gfargrp[0].regs; | |
| /* Stop the DMA, and wait for it to stop */ | |
| tempval = gfar_read(®s->dmactrl); | |
| if ((tempval & (DMACTRL_GRS | DMACTRL_GTS)) | |
| != (DMACTRL_GRS | DMACTRL_GTS)) { | |
| int ret; | |
| tempval |= (DMACTRL_GRS | DMACTRL_GTS); | |
| gfar_write(®s->dmactrl, tempval); | |
| do { | |
| ret = spin_event_timeout(((gfar_read(®s->ievent) & | |
| (IEVENT_GRSC | IEVENT_GTSC)) == | |
| (IEVENT_GRSC | IEVENT_GTSC)), 1000000, 0); | |
| if (!ret && !(gfar_read(®s->ievent) & IEVENT_GRSC)) | |
| ret = __gfar_is_rx_idle(priv); | |
| } while (!ret); | |
| } | |
| } | |
| /* Halt the receive and transmit queues */ | |
| void gfar_halt(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 tempval; | |
| gfar_halt_nodisable(dev); | |
| /* Disable Rx and Tx */ | |
| tempval = gfar_read(®s->maccfg1); | |
| tempval &= ~(MACCFG1_RX_EN | MACCFG1_TX_EN); | |
| gfar_write(®s->maccfg1, tempval); | |
| } | |
| static void free_grp_irqs(struct gfar_priv_grp *grp) | |
| { | |
| free_irq(grp->interruptError, grp); | |
| free_irq(grp->interruptTransmit, grp); | |
| free_irq(grp->interruptReceive, grp); | |
| } | |
| void stop_gfar(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| unsigned long flags; | |
| int i; | |
| phy_stop(priv->phydev); | |
| /* Lock it down */ | |
| local_irq_save(flags); | |
| lock_tx_qs(priv); | |
| lock_rx_qs(priv); | |
| gfar_halt(dev); | |
| unlock_rx_qs(priv); | |
| unlock_tx_qs(priv); | |
| local_irq_restore(flags); | |
| /* Free the IRQs */ | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { | |
| for (i = 0; i < priv->num_grps; i++) | |
| free_grp_irqs(&priv->gfargrp[i]); | |
| } else { | |
| for (i = 0; i < priv->num_grps; i++) | |
| free_irq(priv->gfargrp[i].interruptTransmit, | |
| &priv->gfargrp[i]); | |
| } | |
| free_skb_resources(priv); | |
| } | |
| static void free_skb_tx_queue(struct gfar_priv_tx_q *tx_queue) | |
| { | |
| struct txbd8 *txbdp; | |
| struct gfar_private *priv = netdev_priv(tx_queue->dev); | |
| int i, j; | |
| txbdp = tx_queue->tx_bd_base; | |
| for (i = 0; i < tx_queue->tx_ring_size; i++) { | |
| if (!tx_queue->tx_skbuff[i]) | |
| continue; | |
| dma_unmap_single(&priv->ofdev->dev, txbdp->bufPtr, | |
| txbdp->length, DMA_TO_DEVICE); | |
| txbdp->lstatus = 0; | |
| for (j = 0; j < skb_shinfo(tx_queue->tx_skbuff[i])->nr_frags; | |
| j++) { | |
| txbdp++; | |
| dma_unmap_page(&priv->ofdev->dev, txbdp->bufPtr, | |
| txbdp->length, DMA_TO_DEVICE); | |
| } | |
| txbdp++; | |
| dev_kfree_skb_any(tx_queue->tx_skbuff[i]); | |
| tx_queue->tx_skbuff[i] = NULL; | |
| } | |
| kfree(tx_queue->tx_skbuff); | |
| } | |
| static void free_skb_rx_queue(struct gfar_priv_rx_q *rx_queue) | |
| { | |
| struct rxbd8 *rxbdp; | |
| struct gfar_private *priv = netdev_priv(rx_queue->dev); | |
| int i; | |
| rxbdp = rx_queue->rx_bd_base; | |
| for (i = 0; i < rx_queue->rx_ring_size; i++) { | |
| if (rx_queue->rx_skbuff[i]) { | |
| dma_unmap_single(&priv->ofdev->dev, | |
| rxbdp->bufPtr, priv->rx_buffer_size, | |
| DMA_FROM_DEVICE); | |
| dev_kfree_skb_any(rx_queue->rx_skbuff[i]); | |
| rx_queue->rx_skbuff[i] = NULL; | |
| } | |
| rxbdp->lstatus = 0; | |
| rxbdp->bufPtr = 0; | |
| rxbdp++; | |
| } | |
| kfree(rx_queue->rx_skbuff); | |
| } | |
| /* If there are any tx skbs or rx skbs still around, free them. | |
| * Then free tx_skbuff and rx_skbuff */ | |
| static void free_skb_resources(struct gfar_private *priv) | |
| { | |
| struct gfar_priv_tx_q *tx_queue = NULL; | |
| struct gfar_priv_rx_q *rx_queue = NULL; | |
| int i; | |
| /* Go through all the buffer descriptors and free their data buffers */ | |
| for (i = 0; i < priv->num_tx_queues; i++) { | |
| tx_queue = priv->tx_queue[i]; | |
| if(tx_queue->tx_skbuff) | |
| free_skb_tx_queue(tx_queue); | |
| } | |
| for (i = 0; i < priv->num_rx_queues; i++) { | |
| rx_queue = priv->rx_queue[i]; | |
| if(rx_queue->rx_skbuff) | |
| free_skb_rx_queue(rx_queue); | |
| } | |
| dma_free_coherent(&priv->ofdev->dev, | |
| sizeof(struct txbd8) * priv->total_tx_ring_size + | |
| sizeof(struct rxbd8) * priv->total_rx_ring_size, | |
| priv->tx_queue[0]->tx_bd_base, | |
| priv->tx_queue[0]->tx_bd_dma_base); | |
| skb_queue_purge(&priv->rx_recycle); | |
| } | |
| void gfar_start(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 tempval; | |
| int i = 0; | |
| /* Enable Rx and Tx in MACCFG1 */ | |
| tempval = gfar_read(®s->maccfg1); | |
| tempval |= (MACCFG1_RX_EN | MACCFG1_TX_EN); | |
| gfar_write(®s->maccfg1, tempval); | |
| /* Initialize DMACTRL to have WWR and WOP */ | |
| tempval = gfar_read(®s->dmactrl); | |
| tempval |= DMACTRL_INIT_SETTINGS; | |
| gfar_write(®s->dmactrl, tempval); | |
| /* Make sure we aren't stopped */ | |
| tempval = gfar_read(®s->dmactrl); | |
| tempval &= ~(DMACTRL_GRS | DMACTRL_GTS); | |
| gfar_write(®s->dmactrl, tempval); | |
| for (i = 0; i < priv->num_grps; i++) { | |
| regs = priv->gfargrp[i].regs; | |
| /* Clear THLT/RHLT, so that the DMA starts polling now */ | |
| gfar_write(®s->tstat, priv->gfargrp[i].tstat); | |
| gfar_write(®s->rstat, priv->gfargrp[i].rstat); | |
| /* Unmask the interrupts we look for */ | |
| gfar_write(®s->imask, IMASK_DEFAULT); | |
| } | |
| dev->trans_start = jiffies; /* prevent tx timeout */ | |
| } | |
| void gfar_configure_coalescing(struct gfar_private *priv, | |
| unsigned long tx_mask, unsigned long rx_mask) | |
| { | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 __iomem *baddr; | |
| int i = 0; | |
| /* Backward compatible case ---- even if we enable | |
| * multiple queues, there's only single reg to program | |
| */ | |
| gfar_write(®s->txic, 0); | |
| if(likely(priv->tx_queue[0]->txcoalescing)) | |
| gfar_write(®s->txic, priv->tx_queue[0]->txic); | |
| gfar_write(®s->rxic, 0); | |
| if(unlikely(priv->rx_queue[0]->rxcoalescing)) | |
| gfar_write(®s->rxic, priv->rx_queue[0]->rxic); | |
| if (priv->mode == MQ_MG_MODE) { | |
| baddr = ®s->txic0; | |
| for_each_set_bit(i, &tx_mask, priv->num_tx_queues) { | |
| if (likely(priv->tx_queue[i]->txcoalescing)) { | |
| gfar_write(baddr + i, 0); | |
| gfar_write(baddr + i, priv->tx_queue[i]->txic); | |
| } | |
| } | |
| baddr = ®s->rxic0; | |
| for_each_set_bit(i, &rx_mask, priv->num_rx_queues) { | |
| if (likely(priv->rx_queue[i]->rxcoalescing)) { | |
| gfar_write(baddr + i, 0); | |
| gfar_write(baddr + i, priv->rx_queue[i]->rxic); | |
| } | |
| } | |
| } | |
| } | |
| static int register_grp_irqs(struct gfar_priv_grp *grp) | |
| { | |
| struct gfar_private *priv = grp->priv; | |
| struct net_device *dev = priv->ndev; | |
| int err; | |
| /* If the device has multiple interrupts, register for | |
| * them. Otherwise, only register for the one */ | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { | |
| /* Install our interrupt handlers for Error, | |
| * Transmit, and Receive */ | |
| if ((err = request_irq(grp->interruptError, gfar_error, 0, | |
| grp->int_name_er,grp)) < 0) { | |
| if (netif_msg_intr(priv)) | |
| printk(KERN_ERR "%s: Can't get IRQ %d\n", | |
| dev->name, grp->interruptError); | |
| goto err_irq_fail; | |
| } | |
| if ((err = request_irq(grp->interruptTransmit, gfar_transmit, | |
| 0, grp->int_name_tx, grp)) < 0) { | |
| if (netif_msg_intr(priv)) | |
| printk(KERN_ERR "%s: Can't get IRQ %d\n", | |
| dev->name, grp->interruptTransmit); | |
| goto tx_irq_fail; | |
| } | |
| if ((err = request_irq(grp->interruptReceive, gfar_receive, 0, | |
| grp->int_name_rx, grp)) < 0) { | |
| if (netif_msg_intr(priv)) | |
| printk(KERN_ERR "%s: Can't get IRQ %d\n", | |
| dev->name, grp->interruptReceive); | |
| goto rx_irq_fail; | |
| } | |
| } else { | |
| if ((err = request_irq(grp->interruptTransmit, gfar_interrupt, 0, | |
| grp->int_name_tx, grp)) < 0) { | |
| if (netif_msg_intr(priv)) | |
| printk(KERN_ERR "%s: Can't get IRQ %d\n", | |
| dev->name, grp->interruptTransmit); | |
| goto err_irq_fail; | |
| } | |
| } | |
| return 0; | |
| rx_irq_fail: | |
| free_irq(grp->interruptTransmit, grp); | |
| tx_irq_fail: | |
| free_irq(grp->interruptError, grp); | |
| err_irq_fail: | |
| return err; | |
| } | |
| /* Bring the controller up and running */ | |
| int startup_gfar(struct net_device *ndev) | |
| { | |
| struct gfar_private *priv = netdev_priv(ndev); | |
| struct gfar __iomem *regs = NULL; | |
| int err, i, j; | |
| for (i = 0; i < priv->num_grps; i++) { | |
| regs= priv->gfargrp[i].regs; | |
| gfar_write(®s->imask, IMASK_INIT_CLEAR); | |
| } | |
| regs= priv->gfargrp[0].regs; | |
| err = gfar_alloc_skb_resources(ndev); | |
| if (err) | |
| return err; | |
| gfar_init_mac(ndev); | |
| for (i = 0; i < priv->num_grps; i++) { | |
| err = register_grp_irqs(&priv->gfargrp[i]); | |
| if (err) { | |
| for (j = 0; j < i; j++) | |
| free_grp_irqs(&priv->gfargrp[j]); | |
| goto irq_fail; | |
| } | |
| } | |
| /* Start the controller */ | |
| gfar_start(ndev); | |
| phy_start(priv->phydev); | |
| gfar_configure_coalescing(priv, 0xFF, 0xFF); | |
| return 0; | |
| irq_fail: | |
| free_skb_resources(priv); | |
| return err; | |
| } | |
| /* Called when something needs to use the ethernet device */ | |
| /* Returns 0 for success. */ | |
| static int gfar_enet_open(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| int err; | |
| enable_napi(priv); | |
| skb_queue_head_init(&priv->rx_recycle); | |
| /* Initialize a bunch of registers */ | |
| init_registers(dev); | |
| gfar_set_mac_address(dev); | |
| err = init_phy(dev); | |
| if (err) { | |
| disable_napi(priv); | |
| return err; | |
| } | |
| err = startup_gfar(dev); | |
| if (err) { | |
| disable_napi(priv); | |
| return err; | |
| } | |
| netif_tx_start_all_queues(dev); | |
| device_set_wakeup_enable(&dev->dev, priv->wol_en); | |
| return err; | |
| } | |
| static inline struct txfcb *gfar_add_fcb(struct sk_buff *skb) | |
| { | |
| struct txfcb *fcb = (struct txfcb *)skb_push(skb, GMAC_FCB_LEN); | |
| memset(fcb, 0, GMAC_FCB_LEN); | |
| return fcb; | |
| } | |
| static inline void gfar_tx_checksum(struct sk_buff *skb, struct txfcb *fcb) | |
| { | |
| u8 flags = 0; | |
| /* If we're here, it's a IP packet with a TCP or UDP | |
| * payload. We set it to checksum, using a pseudo-header | |
| * we provide | |
| */ | |
| flags = TXFCB_DEFAULT; | |
| /* Tell the controller what the protocol is */ | |
| /* And provide the already calculated phcs */ | |
| if (ip_hdr(skb)->protocol == IPPROTO_UDP) { | |
| flags |= TXFCB_UDP; | |
| fcb->phcs = udp_hdr(skb)->check; | |
| } else | |
| fcb->phcs = tcp_hdr(skb)->check; | |
| /* l3os is the distance between the start of the | |
| * frame (skb->data) and the start of the IP hdr. | |
| * l4os is the distance between the start of the | |
| * l3 hdr and the l4 hdr */ | |
| fcb->l3os = (u16)(skb_network_offset(skb) - GMAC_FCB_LEN); | |
| fcb->l4os = skb_network_header_len(skb); | |
| fcb->flags = flags; | |
| } | |
| void inline gfar_tx_vlan(struct sk_buff *skb, struct txfcb *fcb) | |
| { | |
| fcb->flags |= TXFCB_VLN; | |
| fcb->vlctl = vlan_tx_tag_get(skb); | |
| } | |
| static inline struct txbd8 *skip_txbd(struct txbd8 *bdp, int stride, | |
| struct txbd8 *base, int ring_size) | |
| { | |
| struct txbd8 *new_bd = bdp + stride; | |
| return (new_bd >= (base + ring_size)) ? (new_bd - ring_size) : new_bd; | |
| } | |
| static inline struct txbd8 *next_txbd(struct txbd8 *bdp, struct txbd8 *base, | |
| int ring_size) | |
| { | |
| return skip_txbd(bdp, 1, base, ring_size); | |
| } | |
| /* This is called by the kernel when a frame is ready for transmission. */ | |
| /* It is pointed to by the dev->hard_start_xmit function pointer */ | |
| static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar_priv_tx_q *tx_queue = NULL; | |
| struct netdev_queue *txq; | |
| struct gfar __iomem *regs = NULL; | |
| struct txfcb *fcb = NULL; | |
| struct txbd8 *txbdp, *txbdp_start, *base, *txbdp_tstamp = NULL; | |
| u32 lstatus; | |
| int i, rq = 0, do_tstamp = 0; | |
| u32 bufaddr; | |
| unsigned long flags; | |
| unsigned int nr_frags, nr_txbds, length; | |
| /* | |
| * TOE=1 frames larger than 2500 bytes may see excess delays | |
| * before start of transmission. | |
| */ | |
| if (unlikely(gfar_has_errata(priv, GFAR_ERRATA_76) && | |
| skb->ip_summed == CHECKSUM_PARTIAL && | |
| skb->len > 2500)) { | |
| int ret; | |
| ret = skb_checksum_help(skb); | |
| if (ret) | |
| return ret; | |
| } | |
| rq = skb->queue_mapping; | |
| tx_queue = priv->tx_queue[rq]; | |
| txq = netdev_get_tx_queue(dev, rq); | |
| base = tx_queue->tx_bd_base; | |
| regs = tx_queue->grp->regs; | |
| /* check if time stamp should be generated */ | |
| if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP && | |
| priv->hwts_tx_en)) | |
| do_tstamp = 1; | |
| /* make space for additional header when fcb is needed */ | |
| if (((skb->ip_summed == CHECKSUM_PARTIAL) || | |
| vlan_tx_tag_present(skb) || | |
| unlikely(do_tstamp)) && | |
| (skb_headroom(skb) < GMAC_FCB_LEN)) { | |
| struct sk_buff *skb_new; | |
| skb_new = skb_realloc_headroom(skb, GMAC_FCB_LEN); | |
| if (!skb_new) { | |
| dev->stats.tx_errors++; | |
| kfree_skb(skb); | |
| return NETDEV_TX_OK; | |
| } | |
| kfree_skb(skb); | |
| skb = skb_new; | |
| } | |
| /* total number of fragments in the SKB */ | |
| nr_frags = skb_shinfo(skb)->nr_frags; | |
| /* calculate the required number of TxBDs for this skb */ | |
| if (unlikely(do_tstamp)) | |
| nr_txbds = nr_frags + 2; | |
| else | |
| nr_txbds = nr_frags + 1; | |
| /* check if there is space to queue this packet */ | |
| if (nr_txbds > tx_queue->num_txbdfree) { | |
| /* no space, stop the queue */ | |
| netif_tx_stop_queue(txq); | |
| dev->stats.tx_fifo_errors++; | |
| return NETDEV_TX_BUSY; | |
| } | |
| /* Update transmit stats */ | |
| tx_queue->stats.tx_bytes += skb->len; | |
| tx_queue->stats.tx_packets++; | |
| txbdp = txbdp_start = tx_queue->cur_tx; | |
| lstatus = txbdp->lstatus; | |
| /* Time stamp insertion requires one additional TxBD */ | |
| if (unlikely(do_tstamp)) | |
| txbdp_tstamp = txbdp = next_txbd(txbdp, base, | |
| tx_queue->tx_ring_size); | |
| if (nr_frags == 0) { | |
| if (unlikely(do_tstamp)) | |
| txbdp_tstamp->lstatus |= BD_LFLAG(TXBD_LAST | | |
| TXBD_INTERRUPT); | |
| else | |
| lstatus |= BD_LFLAG(TXBD_LAST | TXBD_INTERRUPT); | |
| } else { | |
| /* Place the fragment addresses and lengths into the TxBDs */ | |
| for (i = 0; i < nr_frags; i++) { | |
| /* Point at the next BD, wrapping as needed */ | |
| txbdp = next_txbd(txbdp, base, tx_queue->tx_ring_size); | |
| length = skb_shinfo(skb)->frags[i].size; | |
| lstatus = txbdp->lstatus | length | | |
| BD_LFLAG(TXBD_READY); | |
| /* Handle the last BD specially */ | |
| if (i == nr_frags - 1) | |
| lstatus |= BD_LFLAG(TXBD_LAST | TXBD_INTERRUPT); | |
| bufaddr = dma_map_page(&priv->ofdev->dev, | |
| skb_shinfo(skb)->frags[i].page, | |
| skb_shinfo(skb)->frags[i].page_offset, | |
| length, | |
| DMA_TO_DEVICE); | |
| /* set the TxBD length and buffer pointer */ | |
| txbdp->bufPtr = bufaddr; | |
| txbdp->lstatus = lstatus; | |
| } | |
| lstatus = txbdp_start->lstatus; | |
| } | |
| /* Set up checksumming */ | |
| if (CHECKSUM_PARTIAL == skb->ip_summed) { | |
| fcb = gfar_add_fcb(skb); | |
| /* as specified by errata */ | |
| if (unlikely(gfar_has_errata(priv, GFAR_ERRATA_12) | |
| && ((unsigned long)fcb % 0x20) > 0x18)) { | |
| __skb_pull(skb, GMAC_FCB_LEN); | |
| skb_checksum_help(skb); | |
| } else { | |
| lstatus |= BD_LFLAG(TXBD_TOE); | |
| gfar_tx_checksum(skb, fcb); | |
| } | |
| } | |
| if (vlan_tx_tag_present(skb)) { | |
| if (unlikely(NULL == fcb)) { | |
| fcb = gfar_add_fcb(skb); | |
| lstatus |= BD_LFLAG(TXBD_TOE); | |
| } | |
| gfar_tx_vlan(skb, fcb); | |
| } | |
| /* Setup tx hardware time stamping if requested */ | |
| if (unlikely(do_tstamp)) { | |
| skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS; | |
| if (fcb == NULL) | |
| fcb = gfar_add_fcb(skb); | |
| fcb->ptp = 1; | |
| lstatus |= BD_LFLAG(TXBD_TOE); | |
| } | |
| txbdp_start->bufPtr = dma_map_single(&priv->ofdev->dev, skb->data, | |
| skb_headlen(skb), DMA_TO_DEVICE); | |
| /* | |
| * If time stamping is requested one additional TxBD must be set up. The | |
| * first TxBD points to the FCB and must have a data length of | |
| * GMAC_FCB_LEN. The second TxBD points to the actual frame data with | |
| * the full frame length. | |
| */ | |
| if (unlikely(do_tstamp)) { | |
| txbdp_tstamp->bufPtr = txbdp_start->bufPtr + GMAC_FCB_LEN; | |
| txbdp_tstamp->lstatus |= BD_LFLAG(TXBD_READY) | | |
| (skb_headlen(skb) - GMAC_FCB_LEN); | |
| lstatus |= BD_LFLAG(TXBD_CRC | TXBD_READY) | GMAC_FCB_LEN; | |
| } else { | |
| lstatus |= BD_LFLAG(TXBD_CRC | TXBD_READY) | skb_headlen(skb); | |
| } | |
| /* | |
| * We can work in parallel with gfar_clean_tx_ring(), except | |
| * when modifying num_txbdfree. Note that we didn't grab the lock | |
| * when we were reading the num_txbdfree and checking for available | |
| * space, that's because outside of this function it can only grow, | |
| * and once we've got needed space, it cannot suddenly disappear. | |
| * | |
| * The lock also protects us from gfar_error(), which can modify | |
| * regs->tstat and thus retrigger the transfers, which is why we | |
| * also must grab the lock before setting ready bit for the first | |
| * to be transmitted BD. | |
| */ | |
| spin_lock_irqsave(&tx_queue->txlock, flags); | |
| /* | |
| * The powerpc-specific eieio() is used, as wmb() has too strong | |
| * semantics (it requires synchronization between cacheable and | |
| * uncacheable mappings, which eieio doesn't provide and which we | |
| * don't need), thus requiring a more expensive sync instruction. At | |
| * some point, the set of architecture-independent barrier functions | |
| * should be expanded to include weaker barriers. | |
| */ | |
| eieio(); | |
| txbdp_start->lstatus = lstatus; | |
| eieio(); /* force lstatus write before tx_skbuff */ | |
| tx_queue->tx_skbuff[tx_queue->skb_curtx] = skb; | |
| /* Update the current skb pointer to the next entry we will use | |
| * (wrapping if necessary) */ | |
| tx_queue->skb_curtx = (tx_queue->skb_curtx + 1) & | |
| TX_RING_MOD_MASK(tx_queue->tx_ring_size); | |
| tx_queue->cur_tx = next_txbd(txbdp, base, tx_queue->tx_ring_size); | |
| /* reduce TxBD free count */ | |
| tx_queue->num_txbdfree -= (nr_txbds); | |
| /* If the next BD still needs to be cleaned up, then the bds | |
| are full. We need to tell the kernel to stop sending us stuff. */ | |
| if (!tx_queue->num_txbdfree) { | |
| netif_tx_stop_queue(txq); | |
| dev->stats.tx_fifo_errors++; | |
| } | |
| /* Tell the DMA to go go go */ | |
| gfar_write(®s->tstat, TSTAT_CLEAR_THALT >> tx_queue->qindex); | |
| /* Unlock priv */ | |
| spin_unlock_irqrestore(&tx_queue->txlock, flags); | |
| return NETDEV_TX_OK; | |
| } | |
| /* Stops the kernel queue, and halts the controller */ | |
| static int gfar_close(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| disable_napi(priv); | |
| cancel_work_sync(&priv->reset_task); | |
| stop_gfar(dev); | |
| /* Disconnect from the PHY */ | |
| phy_disconnect(priv->phydev); | |
| priv->phydev = NULL; | |
| netif_tx_stop_all_queues(dev); | |
| return 0; | |
| } | |
| /* Changes the mac address if the controller is not running. */ | |
| static int gfar_set_mac_address(struct net_device *dev) | |
| { | |
| gfar_set_mac_for_addr(dev, 0, dev->dev_addr); | |
| return 0; | |
| } | |
| /* Check if rx parser should be activated */ | |
| void gfar_check_rx_parser_mode(struct gfar_private *priv) | |
| { | |
| struct gfar __iomem *regs; | |
| u32 tempval; | |
| regs = priv->gfargrp[0].regs; | |
| tempval = gfar_read(®s->rctrl); | |
| /* If parse is no longer required, then disable parser */ | |
| if (tempval & RCTRL_REQ_PARSER) | |
| tempval |= RCTRL_PRSDEP_INIT; | |
| else | |
| tempval &= ~RCTRL_PRSDEP_INIT; | |
| gfar_write(®s->rctrl, tempval); | |
| } | |
| /* Enables and disables VLAN insertion/extraction */ | |
| static void gfar_vlan_rx_register(struct net_device *dev, | |
| struct vlan_group *grp) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = NULL; | |
| unsigned long flags; | |
| u32 tempval; | |
| regs = priv->gfargrp[0].regs; | |
| local_irq_save(flags); | |
| lock_rx_qs(priv); | |
| priv->vlgrp = grp; | |
| if (grp) { | |
| /* Enable VLAN tag insertion */ | |
| tempval = gfar_read(®s->tctrl); | |
| tempval |= TCTRL_VLINS; | |
| gfar_write(®s->tctrl, tempval); | |
| /* Enable VLAN tag extraction */ | |
| tempval = gfar_read(®s->rctrl); | |
| tempval |= (RCTRL_VLEX | RCTRL_PRSDEP_INIT); | |
| gfar_write(®s->rctrl, tempval); | |
| } else { | |
| /* Disable VLAN tag insertion */ | |
| tempval = gfar_read(®s->tctrl); | |
| tempval &= ~TCTRL_VLINS; | |
| gfar_write(®s->tctrl, tempval); | |
| /* Disable VLAN tag extraction */ | |
| tempval = gfar_read(®s->rctrl); | |
| tempval &= ~RCTRL_VLEX; | |
| gfar_write(®s->rctrl, tempval); | |
| gfar_check_rx_parser_mode(priv); | |
| } | |
| gfar_change_mtu(dev, dev->mtu); | |
| unlock_rx_qs(priv); | |
| local_irq_restore(flags); | |
| } | |
| static int gfar_change_mtu(struct net_device *dev, int new_mtu) | |
| { | |
| int tempsize, tempval; | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| int oldsize = priv->rx_buffer_size; | |
| int frame_size = new_mtu + ETH_HLEN; | |
| if (priv->vlgrp) | |
| frame_size += VLAN_HLEN; | |
| if ((frame_size < 64) || (frame_size > JUMBO_FRAME_SIZE)) { | |
| if (netif_msg_drv(priv)) | |
| printk(KERN_ERR "%s: Invalid MTU setting\n", | |
| dev->name); | |
| return -EINVAL; | |
| } | |
| if (gfar_uses_fcb(priv)) | |
| frame_size += GMAC_FCB_LEN; | |
| frame_size += priv->padding; | |
| tempsize = | |
| (frame_size & ~(INCREMENTAL_BUFFER_SIZE - 1)) + | |
| INCREMENTAL_BUFFER_SIZE; | |
| /* Only stop and start the controller if it isn't already | |
| * stopped, and we changed something */ | |
| if ((oldsize != tempsize) && (dev->flags & IFF_UP)) | |
| stop_gfar(dev); | |
| priv->rx_buffer_size = tempsize; | |
| dev->mtu = new_mtu; | |
| gfar_write(®s->mrblr, priv->rx_buffer_size); | |
| gfar_write(®s->maxfrm, priv->rx_buffer_size); | |
| /* If the mtu is larger than the max size for standard | |
| * ethernet frames (ie, a jumbo frame), then set maccfg2 | |
| * to allow huge frames, and to check the length */ | |
| tempval = gfar_read(®s->maccfg2); | |
| if (priv->rx_buffer_size > DEFAULT_RX_BUFFER_SIZE || | |
| gfar_has_errata(priv, GFAR_ERRATA_74)) | |
| tempval |= (MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK); | |
| else | |
| tempval &= ~(MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK); | |
| gfar_write(®s->maccfg2, tempval); | |
| if ((oldsize != tempsize) && (dev->flags & IFF_UP)) | |
| startup_gfar(dev); | |
| return 0; | |
| } | |
| /* gfar_reset_task gets scheduled when a packet has not been | |
| * transmitted after a set amount of time. | |
| * For now, assume that clearing out all the structures, and | |
| * starting over will fix the problem. | |
| */ | |
| static void gfar_reset_task(struct work_struct *work) | |
| { | |
| struct gfar_private *priv = container_of(work, struct gfar_private, | |
| reset_task); | |
| struct net_device *dev = priv->ndev; | |
| if (dev->flags & IFF_UP) { | |
| netif_tx_stop_all_queues(dev); | |
| stop_gfar(dev); | |
| startup_gfar(dev); | |
| netif_tx_start_all_queues(dev); | |
| } | |
| netif_tx_schedule_all(dev); | |
| } | |
| static void gfar_timeout(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| dev->stats.tx_errors++; | |
| schedule_work(&priv->reset_task); | |
| } | |
| static void gfar_align_skb(struct sk_buff *skb) | |
| { | |
| /* We need the data buffer to be aligned properly. We will reserve | |
| * as many bytes as needed to align the data properly | |
| */ | |
| skb_reserve(skb, RXBUF_ALIGNMENT - | |
| (((unsigned long) skb->data) & (RXBUF_ALIGNMENT - 1))); | |
| } | |
| /* Interrupt Handler for Transmit complete */ | |
| static int gfar_clean_tx_ring(struct gfar_priv_tx_q *tx_queue) | |
| { | |
| struct net_device *dev = tx_queue->dev; | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar_priv_rx_q *rx_queue = NULL; | |
| struct txbd8 *bdp, *next = NULL; | |
| struct txbd8 *lbdp = NULL; | |
| struct txbd8 *base = tx_queue->tx_bd_base; | |
| struct sk_buff *skb; | |
| int skb_dirtytx; | |
| int tx_ring_size = tx_queue->tx_ring_size; | |
| int frags = 0, nr_txbds = 0; | |
| int i; | |
| int howmany = 0; | |
| u32 lstatus; | |
| size_t buflen; | |
| rx_queue = priv->rx_queue[tx_queue->qindex]; | |
| bdp = tx_queue->dirty_tx; | |
| skb_dirtytx = tx_queue->skb_dirtytx; | |
| while ((skb = tx_queue->tx_skbuff[skb_dirtytx])) { | |
| unsigned long flags; | |
| frags = skb_shinfo(skb)->nr_frags; | |
| /* | |
| * When time stamping, one additional TxBD must be freed. | |
| * Also, we need to dma_unmap_single() the TxPAL. | |
| */ | |
| if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS)) | |
| nr_txbds = frags + 2; | |
| else | |
| nr_txbds = frags + 1; | |
| lbdp = skip_txbd(bdp, nr_txbds - 1, base, tx_ring_size); | |
| lstatus = lbdp->lstatus; | |
| /* Only clean completed frames */ | |
| if ((lstatus & BD_LFLAG(TXBD_READY)) && | |
| (lstatus & BD_LENGTH_MASK)) | |
| break; | |
| if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS)) { | |
| next = next_txbd(bdp, base, tx_ring_size); | |
| buflen = next->length + GMAC_FCB_LEN; | |
| } else | |
| buflen = bdp->length; | |
| dma_unmap_single(&priv->ofdev->dev, bdp->bufPtr, | |
| buflen, DMA_TO_DEVICE); | |
| if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS)) { | |
| struct skb_shared_hwtstamps shhwtstamps; | |
| u64 *ns = (u64*) (((u32)skb->data + 0x10) & ~0x7); | |
| memset(&shhwtstamps, 0, sizeof(shhwtstamps)); | |
| shhwtstamps.hwtstamp = ns_to_ktime(*ns); | |
| skb_tstamp_tx(skb, &shhwtstamps); | |
| bdp->lstatus &= BD_LFLAG(TXBD_WRAP); | |
| bdp = next; | |
| } | |
| bdp->lstatus &= BD_LFLAG(TXBD_WRAP); | |
| bdp = next_txbd(bdp, base, tx_ring_size); | |
| for (i = 0; i < frags; i++) { | |
| dma_unmap_page(&priv->ofdev->dev, | |
| bdp->bufPtr, | |
| bdp->length, | |
| DMA_TO_DEVICE); | |
| bdp->lstatus &= BD_LFLAG(TXBD_WRAP); | |
| bdp = next_txbd(bdp, base, tx_ring_size); | |
| } | |
| /* | |
| * If there's room in the queue (limit it to rx_buffer_size) | |
| * we add this skb back into the pool, if it's the right size | |
| */ | |
| if (skb_queue_len(&priv->rx_recycle) < rx_queue->rx_ring_size && | |
| skb_recycle_check(skb, priv->rx_buffer_size + | |
| RXBUF_ALIGNMENT)) { | |
| gfar_align_skb(skb); | |
| skb_queue_head(&priv->rx_recycle, skb); | |
| } else | |
| dev_kfree_skb_any(skb); | |
| tx_queue->tx_skbuff[skb_dirtytx] = NULL; | |
| skb_dirtytx = (skb_dirtytx + 1) & | |
| TX_RING_MOD_MASK(tx_ring_size); | |
| howmany++; | |
| spin_lock_irqsave(&tx_queue->txlock, flags); | |
| tx_queue->num_txbdfree += nr_txbds; | |
| spin_unlock_irqrestore(&tx_queue->txlock, flags); | |
| } | |
| /* If we freed a buffer, we can restart transmission, if necessary */ | |
| if (__netif_subqueue_stopped(dev, tx_queue->qindex) && tx_queue->num_txbdfree) | |
| netif_wake_subqueue(dev, tx_queue->qindex); | |
| /* Update dirty indicators */ | |
| tx_queue->skb_dirtytx = skb_dirtytx; | |
| tx_queue->dirty_tx = bdp; | |
| return howmany; | |
| } | |
| static void gfar_schedule_cleanup(struct gfar_priv_grp *gfargrp) | |
| { | |
| unsigned long flags; | |
| spin_lock_irqsave(&gfargrp->grplock, flags); | |
| if (napi_schedule_prep(&gfargrp->napi)) { | |
| gfar_write(&gfargrp->regs->imask, IMASK_RTX_DISABLED); | |
| __napi_schedule(&gfargrp->napi); | |
| } else { | |
| /* | |
| * Clear IEVENT, so interrupts aren't called again | |
| * because of the packets that have already arrived. | |
| */ | |
| gfar_write(&gfargrp->regs->ievent, IEVENT_RTX_MASK); | |
| } | |
| spin_unlock_irqrestore(&gfargrp->grplock, flags); | |
| } | |
| /* Interrupt Handler for Transmit complete */ | |
| static irqreturn_t gfar_transmit(int irq, void *grp_id) | |
| { | |
| gfar_schedule_cleanup((struct gfar_priv_grp *)grp_id); | |
| return IRQ_HANDLED; | |
| } | |
| static void gfar_new_rxbdp(struct gfar_priv_rx_q *rx_queue, struct rxbd8 *bdp, | |
| struct sk_buff *skb) | |
| { | |
| struct net_device *dev = rx_queue->dev; | |
| struct gfar_private *priv = netdev_priv(dev); | |
| dma_addr_t buf; | |
| buf = dma_map_single(&priv->ofdev->dev, skb->data, | |
| priv->rx_buffer_size, DMA_FROM_DEVICE); | |
| gfar_init_rxbdp(rx_queue, bdp, buf); | |
| } | |
| static struct sk_buff * gfar_alloc_skb(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct sk_buff *skb = NULL; | |
| skb = netdev_alloc_skb(dev, priv->rx_buffer_size + RXBUF_ALIGNMENT); | |
| if (!skb) | |
| return NULL; | |
| gfar_align_skb(skb); | |
| return skb; | |
| } | |
| struct sk_buff * gfar_new_skb(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct sk_buff *skb = NULL; | |
| skb = skb_dequeue(&priv->rx_recycle); | |
| if (!skb) | |
| skb = gfar_alloc_skb(dev); | |
| return skb; | |
| } | |
| static inline void count_errors(unsigned short status, struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct net_device_stats *stats = &dev->stats; | |
| struct gfar_extra_stats *estats = &priv->extra_stats; | |
| /* If the packet was truncated, none of the other errors | |
| * matter */ | |
| if (status & RXBD_TRUNCATED) { | |
| stats->rx_length_errors++; | |
| estats->rx_trunc++; | |
| return; | |
| } | |
| /* Count the errors, if there were any */ | |
| if (status & (RXBD_LARGE | RXBD_SHORT)) { | |
| stats->rx_length_errors++; | |
| if (status & RXBD_LARGE) | |
| estats->rx_large++; | |
| else | |
| estats->rx_short++; | |
| } | |
| if (status & RXBD_NONOCTET) { | |
| stats->rx_frame_errors++; | |
| estats->rx_nonoctet++; | |
| } | |
| if (status & RXBD_CRCERR) { | |
| estats->rx_crcerr++; | |
| stats->rx_crc_errors++; | |
| } | |
| if (status & RXBD_OVERRUN) { | |
| estats->rx_overrun++; | |
| stats->rx_crc_errors++; | |
| } | |
| } | |
| irqreturn_t gfar_receive(int irq, void *grp_id) | |
| { | |
| gfar_schedule_cleanup((struct gfar_priv_grp *)grp_id); | |
| return IRQ_HANDLED; | |
| } | |
| static inline void gfar_rx_checksum(struct sk_buff *skb, struct rxfcb *fcb) | |
| { | |
| /* If valid headers were found, and valid sums | |
| * were verified, then we tell the kernel that no | |
| * checksumming is necessary. Otherwise, it is */ | |
| if ((fcb->flags & RXFCB_CSUM_MASK) == (RXFCB_CIP | RXFCB_CTU)) | |
| skb->ip_summed = CHECKSUM_UNNECESSARY; | |
| else | |
| skb_checksum_none_assert(skb); | |
| } | |
| /* gfar_process_frame() -- handle one incoming packet if skb | |
| * isn't NULL. */ | |
| static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, | |
| int amount_pull) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct rxfcb *fcb = NULL; | |
| int ret; | |
| /* fcb is at the beginning if exists */ | |
| fcb = (struct rxfcb *)skb->data; | |
| /* Remove the FCB from the skb */ | |
| /* Remove the padded bytes, if there are any */ | |
| if (amount_pull) { | |
| skb_record_rx_queue(skb, fcb->rq); | |
| skb_pull(skb, amount_pull); | |
| } | |
| /* Get receive timestamp from the skb */ | |
| if (priv->hwts_rx_en) { | |
| struct skb_shared_hwtstamps *shhwtstamps = skb_hwtstamps(skb); | |
| u64 *ns = (u64 *) skb->data; | |
| memset(shhwtstamps, 0, sizeof(*shhwtstamps)); | |
| shhwtstamps->hwtstamp = ns_to_ktime(*ns); | |
| } | |
| if (priv->padding) | |
| skb_pull(skb, priv->padding); | |
| if (dev->features & NETIF_F_RXCSUM) | |
| gfar_rx_checksum(skb, fcb); | |
| /* Tell the skb what kind of packet this is */ | |
| skb->protocol = eth_type_trans(skb, dev); | |
| /* Send the packet up the stack */ | |
| if (unlikely(priv->vlgrp && (fcb->flags & RXFCB_VLN))) | |
| ret = vlan_hwaccel_receive_skb(skb, priv->vlgrp, fcb->vlctl); | |
| else | |
| ret = netif_receive_skb(skb); | |
| if (NET_RX_DROP == ret) | |
| priv->extra_stats.kernel_dropped++; | |
| return 0; | |
| } | |
| /* gfar_clean_rx_ring() -- Processes each frame in the rx ring | |
| * until the budget/quota has been reached. Returns the number | |
| * of frames handled | |
| */ | |
| int gfar_clean_rx_ring(struct gfar_priv_rx_q *rx_queue, int rx_work_limit) | |
| { | |
| struct net_device *dev = rx_queue->dev; | |
| struct rxbd8 *bdp, *base; | |
| struct sk_buff *skb; | |
| int pkt_len; | |
| int amount_pull; | |
| int howmany = 0; | |
| struct gfar_private *priv = netdev_priv(dev); | |
| /* Get the first full descriptor */ | |
| bdp = rx_queue->cur_rx; | |
| base = rx_queue->rx_bd_base; | |
| amount_pull = (gfar_uses_fcb(priv) ? GMAC_FCB_LEN : 0); | |
| while (!((bdp->status & RXBD_EMPTY) || (--rx_work_limit < 0))) { | |
| struct sk_buff *newskb; | |
| rmb(); | |
| /* Add another skb for the future */ | |
| newskb = gfar_new_skb(dev); | |
| skb = rx_queue->rx_skbuff[rx_queue->skb_currx]; | |
| dma_unmap_single(&priv->ofdev->dev, bdp->bufPtr, | |
| priv->rx_buffer_size, DMA_FROM_DEVICE); | |
| if (unlikely(!(bdp->status & RXBD_ERR) && | |
| bdp->length > priv->rx_buffer_size)) | |
| bdp->status = RXBD_LARGE; | |
| /* We drop the frame if we failed to allocate a new buffer */ | |
| if (unlikely(!newskb || !(bdp->status & RXBD_LAST) || | |
| bdp->status & RXBD_ERR)) { | |
| count_errors(bdp->status, dev); | |
| if (unlikely(!newskb)) | |
| newskb = skb; | |
| else if (skb) | |
| skb_queue_head(&priv->rx_recycle, skb); | |
| } else { | |
| /* Increment the number of packets */ | |
| rx_queue->stats.rx_packets++; | |
| howmany++; | |
| if (likely(skb)) { | |
| pkt_len = bdp->length - ETH_FCS_LEN; | |
| /* Remove the FCS from the packet length */ | |
| skb_put(skb, pkt_len); | |
| rx_queue->stats.rx_bytes += pkt_len; | |
| skb_record_rx_queue(skb, rx_queue->qindex); | |
| gfar_process_frame(dev, skb, amount_pull); | |
| } else { | |
| if (netif_msg_rx_err(priv)) | |
| printk(KERN_WARNING | |
| "%s: Missing skb!\n", dev->name); | |
| rx_queue->stats.rx_dropped++; | |
| priv->extra_stats.rx_skbmissing++; | |
| } | |
| } | |
| rx_queue->rx_skbuff[rx_queue->skb_currx] = newskb; | |
| /* Setup the new bdp */ | |
| gfar_new_rxbdp(rx_queue, bdp, newskb); | |
| /* Update to the next pointer */ | |
| bdp = next_bd(bdp, base, rx_queue->rx_ring_size); | |
| /* update to point at the next skb */ | |
| rx_queue->skb_currx = | |
| (rx_queue->skb_currx + 1) & | |
| RX_RING_MOD_MASK(rx_queue->rx_ring_size); | |
| } | |
| /* Update the current rxbd pointer to be the next one */ | |
| rx_queue->cur_rx = bdp; | |
| return howmany; | |
| } | |
| static int gfar_poll(struct napi_struct *napi, int budget) | |
| { | |
| struct gfar_priv_grp *gfargrp = container_of(napi, | |
| struct gfar_priv_grp, napi); | |
| struct gfar_private *priv = gfargrp->priv; | |
| struct gfar __iomem *regs = gfargrp->regs; | |
| struct gfar_priv_tx_q *tx_queue = NULL; | |
| struct gfar_priv_rx_q *rx_queue = NULL; | |
| int rx_cleaned = 0, budget_per_queue = 0, rx_cleaned_per_queue = 0; | |
| int tx_cleaned = 0, i, left_over_budget = budget; | |
| unsigned long serviced_queues = 0; | |
| int num_queues = 0; | |
| num_queues = gfargrp->num_rx_queues; | |
| budget_per_queue = budget/num_queues; | |
| /* Clear IEVENT, so interrupts aren't called again | |
| * because of the packets that have already arrived */ | |
| gfar_write(®s->ievent, IEVENT_RTX_MASK); | |
| while (num_queues && left_over_budget) { | |
| budget_per_queue = left_over_budget/num_queues; | |
| left_over_budget = 0; | |
| for_each_set_bit(i, &gfargrp->rx_bit_map, priv->num_rx_queues) { | |
| if (test_bit(i, &serviced_queues)) | |
| continue; | |
| rx_queue = priv->rx_queue[i]; | |
| tx_queue = priv->tx_queue[rx_queue->qindex]; | |
| tx_cleaned += gfar_clean_tx_ring(tx_queue); | |
| rx_cleaned_per_queue = gfar_clean_rx_ring(rx_queue, | |
| budget_per_queue); | |
| rx_cleaned += rx_cleaned_per_queue; | |
| if(rx_cleaned_per_queue < budget_per_queue) { | |
| left_over_budget = left_over_budget + | |
| (budget_per_queue - rx_cleaned_per_queue); | |
| set_bit(i, &serviced_queues); | |
| num_queues--; | |
| } | |
| } | |
| } | |
| if (tx_cleaned) | |
| return budget; | |
| if (rx_cleaned < budget) { | |
| napi_complete(napi); | |
| /* Clear the halt bit in RSTAT */ | |
| gfar_write(®s->rstat, gfargrp->rstat); | |
| gfar_write(®s->imask, IMASK_DEFAULT); | |
| /* If we are coalescing interrupts, update the timer */ | |
| /* Otherwise, clear it */ | |
| gfar_configure_coalescing(priv, | |
| gfargrp->rx_bit_map, gfargrp->tx_bit_map); | |
| } | |
| return rx_cleaned; | |
| } | |
| #ifdef CONFIG_NET_POLL_CONTROLLER | |
| /* | |
| * Polling 'interrupt' - used by things like netconsole to send skbs | |
| * without having to re-enable interrupts. It's not called while | |
| * the interrupt routine is executing. | |
| */ | |
| static void gfar_netpoll(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| int i = 0; | |
| /* If the device has multiple interrupts, run tx/rx */ | |
| if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { | |
| for (i = 0; i < priv->num_grps; i++) { | |
| disable_irq(priv->gfargrp[i].interruptTransmit); | |
| disable_irq(priv->gfargrp[i].interruptReceive); | |
| disable_irq(priv->gfargrp[i].interruptError); | |
| gfar_interrupt(priv->gfargrp[i].interruptTransmit, | |
| &priv->gfargrp[i]); | |
| enable_irq(priv->gfargrp[i].interruptError); | |
| enable_irq(priv->gfargrp[i].interruptReceive); | |
| enable_irq(priv->gfargrp[i].interruptTransmit); | |
| } | |
| } else { | |
| for (i = 0; i < priv->num_grps; i++) { | |
| disable_irq(priv->gfargrp[i].interruptTransmit); | |
| gfar_interrupt(priv->gfargrp[i].interruptTransmit, | |
| &priv->gfargrp[i]); | |
| enable_irq(priv->gfargrp[i].interruptTransmit); | |
| } | |
| } | |
| } | |
| #endif | |
| /* The interrupt handler for devices with one interrupt */ | |
| static irqreturn_t gfar_interrupt(int irq, void *grp_id) | |
| { | |
| struct gfar_priv_grp *gfargrp = grp_id; | |
| /* Save ievent for future reference */ | |
| u32 events = gfar_read(&gfargrp->regs->ievent); | |
| /* Check for reception */ | |
| if (events & IEVENT_RX_MASK) | |
| gfar_receive(irq, grp_id); | |
| /* Check for transmit completion */ | |
| if (events & IEVENT_TX_MASK) | |
| gfar_transmit(irq, grp_id); | |
| /* Check for errors */ | |
| if (events & IEVENT_ERR_MASK) | |
| gfar_error(irq, grp_id); | |
| return IRQ_HANDLED; | |
| } | |
| /* Called every time the controller might need to be made | |
| * aware of new link state. The PHY code conveys this | |
| * information through variables in the phydev structure, and this | |
| * function converts those variables into the appropriate | |
| * register values, and can bring down the device if needed. | |
| */ | |
| static void adjust_link(struct net_device *dev) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| unsigned long flags; | |
| struct phy_device *phydev = priv->phydev; | |
| int new_state = 0; | |
| local_irq_save(flags); | |
| lock_tx_qs(priv); | |
| if (phydev->link) { | |
| u32 tempval = gfar_read(®s->maccfg2); | |
| u32 ecntrl = gfar_read(®s->ecntrl); | |
| /* Now we make sure that we can be in full duplex mode. | |
| * If not, we operate in half-duplex mode. */ | |
| if (phydev->duplex != priv->oldduplex) { | |
| new_state = 1; | |
| if (!(phydev->duplex)) | |
| tempval &= ~(MACCFG2_FULL_DUPLEX); | |
| else | |
| tempval |= MACCFG2_FULL_DUPLEX; | |
| priv->oldduplex = phydev->duplex; | |
| } | |
| if (phydev->speed != priv->oldspeed) { | |
| new_state = 1; | |
| switch (phydev->speed) { | |
| case 1000: | |
| tempval = | |
| ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII); | |
| ecntrl &= ~(ECNTRL_R100); | |
| break; | |
| case 100: | |
| case 10: | |
| tempval = | |
| ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII); | |
| /* Reduced mode distinguishes | |
| * between 10 and 100 */ | |
| if (phydev->speed == SPEED_100) | |
| ecntrl |= ECNTRL_R100; | |
| else | |
| ecntrl &= ~(ECNTRL_R100); | |
| break; | |
| default: | |
| if (netif_msg_link(priv)) | |
| printk(KERN_WARNING | |
| "%s: Ack! Speed (%d) is not 10/100/1000!\n", | |
| dev->name, phydev->speed); | |
| break; | |
| } | |
| priv->oldspeed = phydev->speed; | |
| } | |
| gfar_write(®s->maccfg2, tempval); | |
| gfar_write(®s->ecntrl, ecntrl); | |
| if (!priv->oldlink) { | |
| new_state = 1; | |
| priv->oldlink = 1; | |
| } | |
| } else if (priv->oldlink) { | |
| new_state = 1; | |
| priv->oldlink = 0; | |
| priv->oldspeed = 0; | |
| priv->oldduplex = -1; | |
| } | |
| if (new_state && netif_msg_link(priv)) | |
| phy_print_status(phydev); | |
| unlock_tx_qs(priv); | |
| local_irq_restore(flags); | |
| } | |
| /* Update the hash table based on the current list of multicast | |
| * addresses we subscribe to. Also, change the promiscuity of | |
| * the device based on the flags (this function is called | |
| * whenever dev->flags is changed */ | |
| static void gfar_set_multi(struct net_device *dev) | |
| { | |
| struct netdev_hw_addr *ha; | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| u32 tempval; | |
| if (dev->flags & IFF_PROMISC) { | |
| /* Set RCTRL to PROM */ | |
| tempval = gfar_read(®s->rctrl); | |
| tempval |= RCTRL_PROM; | |
| gfar_write(®s->rctrl, tempval); | |
| } else { | |
| /* Set RCTRL to not PROM */ | |
| tempval = gfar_read(®s->rctrl); | |
| tempval &= ~(RCTRL_PROM); | |
| gfar_write(®s->rctrl, tempval); | |
| } | |
| if (dev->flags & IFF_ALLMULTI) { | |
| /* Set the hash to rx all multicast frames */ | |
| gfar_write(®s->igaddr0, 0xffffffff); | |
| gfar_write(®s->igaddr1, 0xffffffff); | |
| gfar_write(®s->igaddr2, 0xffffffff); | |
| gfar_write(®s->igaddr3, 0xffffffff); | |
| gfar_write(®s->igaddr4, 0xffffffff); | |
| gfar_write(®s->igaddr5, 0xffffffff); | |
| gfar_write(®s->igaddr6, 0xffffffff); | |
| gfar_write(®s->igaddr7, 0xffffffff); | |
| gfar_write(®s->gaddr0, 0xffffffff); | |
| gfar_write(®s->gaddr1, 0xffffffff); | |
| gfar_write(®s->gaddr2, 0xffffffff); | |
| gfar_write(®s->gaddr3, 0xffffffff); | |
| gfar_write(®s->gaddr4, 0xffffffff); | |
| gfar_write(®s->gaddr5, 0xffffffff); | |
| gfar_write(®s->gaddr6, 0xffffffff); | |
| gfar_write(®s->gaddr7, 0xffffffff); | |
| } else { | |
| int em_num; | |
| int idx; | |
| /* zero out the hash */ | |
| gfar_write(®s->igaddr0, 0x0); | |
| gfar_write(®s->igaddr1, 0x0); | |
| gfar_write(®s->igaddr2, 0x0); | |
| gfar_write(®s->igaddr3, 0x0); | |
| gfar_write(®s->igaddr4, 0x0); | |
| gfar_write(®s->igaddr5, 0x0); | |
| gfar_write(®s->igaddr6, 0x0); | |
| gfar_write(®s->igaddr7, 0x0); | |
| gfar_write(®s->gaddr0, 0x0); | |
| gfar_write(®s->gaddr1, 0x0); | |
| gfar_write(®s->gaddr2, 0x0); | |
| gfar_write(®s->gaddr3, 0x0); | |
| gfar_write(®s->gaddr4, 0x0); | |
| gfar_write(®s->gaddr5, 0x0); | |
| gfar_write(®s->gaddr6, 0x0); | |
| gfar_write(®s->gaddr7, 0x0); | |
| /* If we have extended hash tables, we need to | |
| * clear the exact match registers to prepare for | |
| * setting them */ | |
| if (priv->extended_hash) { | |
| em_num = GFAR_EM_NUM + 1; | |
| gfar_clear_exact_match(dev); | |
| idx = 1; | |
| } else { | |
| idx = 0; | |
| em_num = 0; | |
| } | |
| if (netdev_mc_empty(dev)) | |
| return; | |
| /* Parse the list, and set the appropriate bits */ | |
| netdev_for_each_mc_addr(ha, dev) { | |
| if (idx < em_num) { | |
| gfar_set_mac_for_addr(dev, idx, ha->addr); | |
| idx++; | |
| } else | |
| gfar_set_hash_for_addr(dev, ha->addr); | |
| } | |
| } | |
| } | |
| /* Clears each of the exact match registers to zero, so they | |
| * don't interfere with normal reception */ | |
| static void gfar_clear_exact_match(struct net_device *dev) | |
| { | |
| int idx; | |
| static const u8 zero_arr[MAC_ADDR_LEN] = {0, 0, 0, 0, 0, 0}; | |
| for(idx = 1;idx < GFAR_EM_NUM + 1;idx++) | |
| gfar_set_mac_for_addr(dev, idx, zero_arr); | |
| } | |
| /* Set the appropriate hash bit for the given addr */ | |
| /* The algorithm works like so: | |
| * 1) Take the Destination Address (ie the multicast address), and | |
| * do a CRC on it (little endian), and reverse the bits of the | |
| * result. | |
| * 2) Use the 8 most significant bits as a hash into a 256-entry | |
| * table. The table is controlled through 8 32-bit registers: | |
| * gaddr0-7. gaddr0's MSB is entry 0, and gaddr7's LSB is | |
| * gaddr7. This means that the 3 most significant bits in the | |
| * hash index which gaddr register to use, and the 5 other bits | |
| * indicate which bit (assuming an IBM numbering scheme, which | |
| * for PowerPC (tm) is usually the case) in the register holds | |
| * the entry. */ | |
| static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr) | |
| { | |
| u32 tempval; | |
| struct gfar_private *priv = netdev_priv(dev); | |
| u32 result = ether_crc(MAC_ADDR_LEN, addr); | |
| int width = priv->hash_width; | |
| u8 whichbit = (result >> (32 - width)) & 0x1f; | |
| u8 whichreg = result >> (32 - width + 5); | |
| u32 value = (1 << (31-whichbit)); | |
| tempval = gfar_read(priv->hash_regs[whichreg]); | |
| tempval |= value; | |
| gfar_write(priv->hash_regs[whichreg], tempval); | |
| } | |
| /* There are multiple MAC Address register pairs on some controllers | |
| * This function sets the numth pair to a given address | |
| */ | |
| static void gfar_set_mac_for_addr(struct net_device *dev, int num, | |
| const u8 *addr) | |
| { | |
| struct gfar_private *priv = netdev_priv(dev); | |
| struct gfar __iomem *regs = priv->gfargrp[0].regs; | |
| int idx; | |
| char tmpbuf[MAC_ADDR_LEN]; | |
| u32 tempval; | |
| u32 __iomem *macptr = ®s->macstnaddr1; | |
| macptr += num*2; | |
| /* Now copy it into the mac registers backwards, cuz */ | |
| /* little endian is silly */ | |
| for (idx = 0; idx < MAC_ADDR_LEN; idx++) | |
| tmpbuf[MAC_ADDR_LEN - 1 - idx] = addr[idx]; | |
| gfar_write(macptr, *((u32 *) (tmpbuf))); | |
| tempval = *((u32 *) (tmpbuf + 4)); | |
| gfar_write(macptr+1, tempval); | |
| } | |
| /* GFAR error interrupt handler */ | |
| static irqreturn_t gfar_error(int irq, void *grp_id) | |
| { | |
| struct gfar_priv_grp *gfargrp = grp_id; | |
| struct gfar __iomem *regs = gfargrp->regs; | |
| struct gfar_private *priv= gfargrp->priv; | |
| struct net_device *dev = priv->ndev; | |
| /* Save ievent for future reference */ | |
| u32 events = gfar_read(®s->ievent); | |
| /* Clear IEVENT */ | |
| gfar_write(®s->ievent, events & IEVENT_ERR_MASK); | |
| /* Magic Packet is not an error. */ | |
| if ((priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) && | |
| (events & IEVENT_MAG)) | |
| events &= ~IEVENT_MAG; | |
| /* Hmm... */ | |
| if (netif_msg_rx_err(priv) || netif_msg_tx_err(priv)) | |
| printk(KERN_DEBUG "%s: error interrupt (ievent=0x%08x imask=0x%08x)\n", | |
| dev->name, events, gfar_read(®s->imask)); | |
| /* Update the error counters */ | |
| if (events & IEVENT_TXE) { | |
| dev->stats.tx_errors++; | |
| if (events & IEVENT_LC) | |
| dev->stats.tx_window_errors++; | |
| if (events & IEVENT_CRL) | |
| dev->stats.tx_aborted_errors++; | |
| if (events & IEVENT_XFUN) { | |
| unsigned long flags; | |
| if (netif_msg_tx_err(priv)) | |
| printk(KERN_DEBUG "%s: TX FIFO underrun, " | |
| "packet dropped.\n", dev->name); | |
| dev->stats.tx_dropped++; | |
| priv->extra_stats.tx_underrun++; | |
| local_irq_save(flags); | |
| lock_tx_qs(priv); | |
| /* Reactivate the Tx Queues */ | |
| gfar_write(®s->tstat, gfargrp->tstat); | |
| unlock_tx_qs(priv); | |
| local_irq_restore(flags); | |
| } | |
| if (netif_msg_tx_err(priv)) | |
| printk(KERN_DEBUG "%s: Transmit Error\n", dev->name); | |
| } | |
| if (events & IEVENT_BSY) { | |
| dev->stats.rx_errors++; | |
| priv->extra_stats.rx_bsy++; | |
| gfar_receive(irq, grp_id); | |
| if (netif_msg_rx_err(priv)) | |
| printk(KERN_DEBUG "%s: busy error (rstat: %x)\n", | |
| dev->name, gfar_read(®s->rstat)); | |
| } | |
| if (events & IEVENT_BABR) { | |
| dev->stats.rx_errors++; | |
| priv->extra_stats.rx_babr++; | |
| if (netif_msg_rx_err(priv)) | |
| printk(KERN_DEBUG "%s: babbling RX error\n", dev->name); | |
| } | |
| if (events & IEVENT_EBERR) { | |
| priv->extra_stats.eberr++; | |
| if (netif_msg_rx_err(priv)) | |
| printk(KERN_DEBUG "%s: bus error\n", dev->name); | |
| } | |
| if ((events & IEVENT_RXC) && netif_msg_rx_status(priv)) | |
| printk(KERN_DEBUG "%s: control frame\n", dev->name); | |
| if (events & IEVENT_BABT) { | |
| priv->extra_stats.tx_babt++; | |
| if (netif_msg_tx_err(priv)) | |
| printk(KERN_DEBUG "%s: babbling TX error\n", dev->name); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static struct of_device_id gfar_match[] = | |
| { | |
| { | |
| .type = "network", | |
| .compatible = "gianfar", | |
| }, | |
| { | |
| .compatible = "fsl,etsec2", | |
| }, | |
| {}, | |
| }; | |
| MODULE_DEVICE_TABLE(of, gfar_match); | |
| /* Structure for a device driver */ | |
| static struct platform_driver gfar_driver = { | |
| .driver = { | |
| .name = "fsl-gianfar", | |
| .owner = THIS_MODULE, | |
| .pm = GFAR_PM_OPS, | |
| .of_match_table = gfar_match, | |
| }, | |
| .probe = gfar_probe, | |
| .remove = gfar_remove, | |
| }; | |
| static int __init gfar_init(void) | |
| { | |
| return platform_driver_register(&gfar_driver); | |
| } | |
| static void __exit gfar_exit(void) | |
| { | |
| platform_driver_unregister(&gfar_driver); | |
| } | |
| module_init(gfar_init); | |
| module_exit(gfar_exit); | |