| /* | |
| * dw_spi.c - Designware SPI core controller driver (refer pxa2xx_spi.c) | |
| * | |
| * Copyright (c) 2009, Intel Corporation. | |
| * | |
| * This program is free software; you can redistribute it and/or modify it | |
| * under the terms and conditions of the GNU General Public License, | |
| * version 2, as published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope it will be useful, but WITHOUT | |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for | |
| * more details. | |
| * | |
| * You should have received a copy of the GNU General Public License along with | |
| * this program; if not, write to the Free Software Foundation, Inc., | |
| * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. | |
| */ | |
| #include <linux/dma-mapping.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/highmem.h> | |
| #include <linux/delay.h> | |
| #include <linux/slab.h> | |
| #include <linux/spi/spi.h> | |
| #include "dw_spi.h" | |
| #ifdef CONFIG_DEBUG_FS | |
| #include <linux/debugfs.h> | |
| #endif | |
| #define START_STATE ((void *)0) | |
| #define RUNNING_STATE ((void *)1) | |
| #define DONE_STATE ((void *)2) | |
| #define ERROR_STATE ((void *)-1) | |
| #define QUEUE_RUNNING 0 | |
| #define QUEUE_STOPPED 1 | |
| #define MRST_SPI_DEASSERT 0 | |
| #define MRST_SPI_ASSERT 1 | |
| /* Slave spi_dev related */ | |
| struct chip_data { | |
| u16 cr0; | |
| u8 cs; /* chip select pin */ | |
| u8 n_bytes; /* current is a 1/2/4 byte op */ | |
| u8 tmode; /* TR/TO/RO/EEPROM */ | |
| u8 type; /* SPI/SSP/MicroWire */ | |
| u8 poll_mode; /* 1 means use poll mode */ | |
| u32 dma_width; | |
| u32 rx_threshold; | |
| u32 tx_threshold; | |
| u8 enable_dma; | |
| u8 bits_per_word; | |
| u16 clk_div; /* baud rate divider */ | |
| u32 speed_hz; /* baud rate */ | |
| void (*cs_control)(u32 command); | |
| }; | |
| #ifdef CONFIG_DEBUG_FS | |
| static int spi_show_regs_open(struct inode *inode, struct file *file) | |
| { | |
| file->private_data = inode->i_private; | |
| return 0; | |
| } | |
| #define SPI_REGS_BUFSIZE 1024 | |
| static ssize_t spi_show_regs(struct file *file, char __user *user_buf, | |
| size_t count, loff_t *ppos) | |
| { | |
| struct dw_spi *dws; | |
| char *buf; | |
| u32 len = 0; | |
| ssize_t ret; | |
| dws = file->private_data; | |
| buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL); | |
| if (!buf) | |
| return 0; | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "MRST SPI0 registers:\n"); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "=================================\n"); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "CTRL0: \t\t0x%08x\n", dw_readl(dws, ctrl0)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "CTRL1: \t\t0x%08x\n", dw_readl(dws, ctrl1)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "SSIENR: \t0x%08x\n", dw_readl(dws, ssienr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "SER: \t\t0x%08x\n", dw_readl(dws, ser)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "BAUDR: \t\t0x%08x\n", dw_readl(dws, baudr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "TXFTLR: \t0x%08x\n", dw_readl(dws, txfltr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "RXFTLR: \t0x%08x\n", dw_readl(dws, rxfltr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "TXFLR: \t\t0x%08x\n", dw_readl(dws, txflr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "RXFLR: \t\t0x%08x\n", dw_readl(dws, rxflr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "SR: \t\t0x%08x\n", dw_readl(dws, sr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "IMR: \t\t0x%08x\n", dw_readl(dws, imr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "ISR: \t\t0x%08x\n", dw_readl(dws, isr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "DMACR: \t\t0x%08x\n", dw_readl(dws, dmacr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "DMATDLR: \t0x%08x\n", dw_readl(dws, dmatdlr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "DMARDLR: \t0x%08x\n", dw_readl(dws, dmardlr)); | |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, | |
| "=================================\n"); | |
| ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); | |
| kfree(buf); | |
| return ret; | |
| } | |
| static const struct file_operations mrst_spi_regs_ops = { | |
| .owner = THIS_MODULE, | |
| .open = spi_show_regs_open, | |
| .read = spi_show_regs, | |
| .llseek = default_llseek, | |
| }; | |
| static int mrst_spi_debugfs_init(struct dw_spi *dws) | |
| { | |
| dws->debugfs = debugfs_create_dir("mrst_spi", NULL); | |
| if (!dws->debugfs) | |
| return -ENOMEM; | |
| debugfs_create_file("registers", S_IFREG | S_IRUGO, | |
| dws->debugfs, (void *)dws, &mrst_spi_regs_ops); | |
| return 0; | |
| } | |
| static void mrst_spi_debugfs_remove(struct dw_spi *dws) | |
| { | |
| if (dws->debugfs) | |
| debugfs_remove_recursive(dws->debugfs); | |
| } | |
| #else | |
| static inline int mrst_spi_debugfs_init(struct dw_spi *dws) | |
| { | |
| return 0; | |
| } | |
| static inline void mrst_spi_debugfs_remove(struct dw_spi *dws) | |
| { | |
| } | |
| #endif /* CONFIG_DEBUG_FS */ | |
| /* Return the max entries we can fill into tx fifo */ | |
| static inline u32 tx_max(struct dw_spi *dws) | |
| { | |
| u32 tx_left, tx_room, rxtx_gap; | |
| tx_left = (dws->tx_end - dws->tx) / dws->n_bytes; | |
| tx_room = dws->fifo_len - dw_readw(dws, txflr); | |
| /* | |
| * Another concern is about the tx/rx mismatch, we | |
| * though to use (dws->fifo_len - rxflr - txflr) as | |
| * one maximum value for tx, but it doesn't cover the | |
| * data which is out of tx/rx fifo and inside the | |
| * shift registers. So a control from sw point of | |
| * view is taken. | |
| */ | |
| rxtx_gap = ((dws->rx_end - dws->rx) - (dws->tx_end - dws->tx)) | |
| / dws->n_bytes; | |
| return min3(tx_left, tx_room, (u32) (dws->fifo_len - rxtx_gap)); | |
| } | |
| /* Return the max entries we should read out of rx fifo */ | |
| static inline u32 rx_max(struct dw_spi *dws) | |
| { | |
| u32 rx_left = (dws->rx_end - dws->rx) / dws->n_bytes; | |
| return min(rx_left, (u32)dw_readw(dws, rxflr)); | |
| } | |
| static void dw_writer(struct dw_spi *dws) | |
| { | |
| u32 max = tx_max(dws); | |
| u16 txw = 0; | |
| while (max--) { | |
| /* Set the tx word if the transfer's original "tx" is not null */ | |
| if (dws->tx_end - dws->len) { | |
| if (dws->n_bytes == 1) | |
| txw = *(u8 *)(dws->tx); | |
| else | |
| txw = *(u16 *)(dws->tx); | |
| } | |
| dw_writew(dws, dr, txw); | |
| dws->tx += dws->n_bytes; | |
| } | |
| } | |
| static void dw_reader(struct dw_spi *dws) | |
| { | |
| u32 max = rx_max(dws); | |
| u16 rxw; | |
| while (max--) { | |
| rxw = dw_readw(dws, dr); | |
| /* Care rx only if the transfer's original "rx" is not null */ | |
| if (dws->rx_end - dws->len) { | |
| if (dws->n_bytes == 1) | |
| *(u8 *)(dws->rx) = rxw; | |
| else | |
| *(u16 *)(dws->rx) = rxw; | |
| } | |
| dws->rx += dws->n_bytes; | |
| } | |
| } | |
| static void *next_transfer(struct dw_spi *dws) | |
| { | |
| struct spi_message *msg = dws->cur_msg; | |
| struct spi_transfer *trans = dws->cur_transfer; | |
| /* Move to next transfer */ | |
| if (trans->transfer_list.next != &msg->transfers) { | |
| dws->cur_transfer = | |
| list_entry(trans->transfer_list.next, | |
| struct spi_transfer, | |
| transfer_list); | |
| return RUNNING_STATE; | |
| } else | |
| return DONE_STATE; | |
| } | |
| /* | |
| * Note: first step is the protocol driver prepares | |
| * a dma-capable memory, and this func just need translate | |
| * the virt addr to physical | |
| */ | |
| static int map_dma_buffers(struct dw_spi *dws) | |
| { | |
| if (!dws->cur_msg->is_dma_mapped | |
| || !dws->dma_inited | |
| || !dws->cur_chip->enable_dma | |
| || !dws->dma_ops) | |
| return 0; | |
| if (dws->cur_transfer->tx_dma) | |
| dws->tx_dma = dws->cur_transfer->tx_dma; | |
| if (dws->cur_transfer->rx_dma) | |
| dws->rx_dma = dws->cur_transfer->rx_dma; | |
| return 1; | |
| } | |
| /* Caller already set message->status; dma and pio irqs are blocked */ | |
| static void giveback(struct dw_spi *dws) | |
| { | |
| struct spi_transfer *last_transfer; | |
| unsigned long flags; | |
| struct spi_message *msg; | |
| spin_lock_irqsave(&dws->lock, flags); | |
| msg = dws->cur_msg; | |
| dws->cur_msg = NULL; | |
| dws->cur_transfer = NULL; | |
| dws->prev_chip = dws->cur_chip; | |
| dws->cur_chip = NULL; | |
| dws->dma_mapped = 0; | |
| queue_work(dws->workqueue, &dws->pump_messages); | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| last_transfer = list_entry(msg->transfers.prev, | |
| struct spi_transfer, | |
| transfer_list); | |
| if (!last_transfer->cs_change && dws->cs_control) | |
| dws->cs_control(MRST_SPI_DEASSERT); | |
| msg->state = NULL; | |
| if (msg->complete) | |
| msg->complete(msg->context); | |
| } | |
| static void int_error_stop(struct dw_spi *dws, const char *msg) | |
| { | |
| /* Stop the hw */ | |
| spi_enable_chip(dws, 0); | |
| dev_err(&dws->master->dev, "%s\n", msg); | |
| dws->cur_msg->state = ERROR_STATE; | |
| tasklet_schedule(&dws->pump_transfers); | |
| } | |
| void dw_spi_xfer_done(struct dw_spi *dws) | |
| { | |
| /* Update total byte transferred return count actual bytes read */ | |
| dws->cur_msg->actual_length += dws->len; | |
| /* Move to next transfer */ | |
| dws->cur_msg->state = next_transfer(dws); | |
| /* Handle end of message */ | |
| if (dws->cur_msg->state == DONE_STATE) { | |
| dws->cur_msg->status = 0; | |
| giveback(dws); | |
| } else | |
| tasklet_schedule(&dws->pump_transfers); | |
| } | |
| EXPORT_SYMBOL_GPL(dw_spi_xfer_done); | |
| static irqreturn_t interrupt_transfer(struct dw_spi *dws) | |
| { | |
| u16 irq_status = dw_readw(dws, isr); | |
| /* Error handling */ | |
| if (irq_status & (SPI_INT_TXOI | SPI_INT_RXOI | SPI_INT_RXUI)) { | |
| dw_readw(dws, txoicr); | |
| dw_readw(dws, rxoicr); | |
| dw_readw(dws, rxuicr); | |
| int_error_stop(dws, "interrupt_transfer: fifo overrun/underrun"); | |
| return IRQ_HANDLED; | |
| } | |
| dw_reader(dws); | |
| if (dws->rx_end == dws->rx) { | |
| spi_mask_intr(dws, SPI_INT_TXEI); | |
| dw_spi_xfer_done(dws); | |
| return IRQ_HANDLED; | |
| } | |
| if (irq_status & SPI_INT_TXEI) { | |
| spi_mask_intr(dws, SPI_INT_TXEI); | |
| dw_writer(dws); | |
| /* Enable TX irq always, it will be disabled when RX finished */ | |
| spi_umask_intr(dws, SPI_INT_TXEI); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static irqreturn_t dw_spi_irq(int irq, void *dev_id) | |
| { | |
| struct dw_spi *dws = dev_id; | |
| u16 irq_status = dw_readw(dws, isr) & 0x3f; | |
| if (!irq_status) | |
| return IRQ_NONE; | |
| if (!dws->cur_msg) { | |
| spi_mask_intr(dws, SPI_INT_TXEI); | |
| return IRQ_HANDLED; | |
| } | |
| return dws->transfer_handler(dws); | |
| } | |
| /* Must be called inside pump_transfers() */ | |
| static void poll_transfer(struct dw_spi *dws) | |
| { | |
| do { | |
| dw_writer(dws); | |
| dw_reader(dws); | |
| cpu_relax(); | |
| } while (dws->rx_end > dws->rx); | |
| dw_spi_xfer_done(dws); | |
| } | |
| static void pump_transfers(unsigned long data) | |
| { | |
| struct dw_spi *dws = (struct dw_spi *)data; | |
| struct spi_message *message = NULL; | |
| struct spi_transfer *transfer = NULL; | |
| struct spi_transfer *previous = NULL; | |
| struct spi_device *spi = NULL; | |
| struct chip_data *chip = NULL; | |
| u8 bits = 0; | |
| u8 imask = 0; | |
| u8 cs_change = 0; | |
| u16 txint_level = 0; | |
| u16 clk_div = 0; | |
| u32 speed = 0; | |
| u32 cr0 = 0; | |
| /* Get current state information */ | |
| message = dws->cur_msg; | |
| transfer = dws->cur_transfer; | |
| chip = dws->cur_chip; | |
| spi = message->spi; | |
| if (unlikely(!chip->clk_div)) | |
| chip->clk_div = dws->max_freq / chip->speed_hz; | |
| if (message->state == ERROR_STATE) { | |
| message->status = -EIO; | |
| goto early_exit; | |
| } | |
| /* Handle end of message */ | |
| if (message->state == DONE_STATE) { | |
| message->status = 0; | |
| goto early_exit; | |
| } | |
| /* Delay if requested at end of transfer*/ | |
| if (message->state == RUNNING_STATE) { | |
| previous = list_entry(transfer->transfer_list.prev, | |
| struct spi_transfer, | |
| transfer_list); | |
| if (previous->delay_usecs) | |
| udelay(previous->delay_usecs); | |
| } | |
| dws->n_bytes = chip->n_bytes; | |
| dws->dma_width = chip->dma_width; | |
| dws->cs_control = chip->cs_control; | |
| dws->rx_dma = transfer->rx_dma; | |
| dws->tx_dma = transfer->tx_dma; | |
| dws->tx = (void *)transfer->tx_buf; | |
| dws->tx_end = dws->tx + transfer->len; | |
| dws->rx = transfer->rx_buf; | |
| dws->rx_end = dws->rx + transfer->len; | |
| dws->cs_change = transfer->cs_change; | |
| dws->len = dws->cur_transfer->len; | |
| if (chip != dws->prev_chip) | |
| cs_change = 1; | |
| cr0 = chip->cr0; | |
| /* Handle per transfer options for bpw and speed */ | |
| if (transfer->speed_hz) { | |
| speed = chip->speed_hz; | |
| if (transfer->speed_hz != speed) { | |
| speed = transfer->speed_hz; | |
| if (speed > dws->max_freq) { | |
| printk(KERN_ERR "MRST SPI0: unsupported" | |
| "freq: %dHz\n", speed); | |
| message->status = -EIO; | |
| goto early_exit; | |
| } | |
| /* clk_div doesn't support odd number */ | |
| clk_div = dws->max_freq / speed; | |
| clk_div = (clk_div + 1) & 0xfffe; | |
| chip->speed_hz = speed; | |
| chip->clk_div = clk_div; | |
| } | |
| } | |
| if (transfer->bits_per_word) { | |
| bits = transfer->bits_per_word; | |
| switch (bits) { | |
| case 8: | |
| case 16: | |
| dws->n_bytes = dws->dma_width = bits >> 3; | |
| break; | |
| default: | |
| printk(KERN_ERR "MRST SPI0: unsupported bits:" | |
| "%db\n", bits); | |
| message->status = -EIO; | |
| goto early_exit; | |
| } | |
| cr0 = (bits - 1) | |
| | (chip->type << SPI_FRF_OFFSET) | |
| | (spi->mode << SPI_MODE_OFFSET) | |
| | (chip->tmode << SPI_TMOD_OFFSET); | |
| } | |
| message->state = RUNNING_STATE; | |
| /* | |
| * Adjust transfer mode if necessary. Requires platform dependent | |
| * chipselect mechanism. | |
| */ | |
| if (dws->cs_control) { | |
| if (dws->rx && dws->tx) | |
| chip->tmode = SPI_TMOD_TR; | |
| else if (dws->rx) | |
| chip->tmode = SPI_TMOD_RO; | |
| else | |
| chip->tmode = SPI_TMOD_TO; | |
| cr0 &= ~SPI_TMOD_MASK; | |
| cr0 |= (chip->tmode << SPI_TMOD_OFFSET); | |
| } | |
| /* Check if current transfer is a DMA transaction */ | |
| dws->dma_mapped = map_dma_buffers(dws); | |
| /* | |
| * Interrupt mode | |
| * we only need set the TXEI IRQ, as TX/RX always happen syncronizely | |
| */ | |
| if (!dws->dma_mapped && !chip->poll_mode) { | |
| int templen = dws->len / dws->n_bytes; | |
| txint_level = dws->fifo_len / 2; | |
| txint_level = (templen > txint_level) ? txint_level : templen; | |
| imask |= SPI_INT_TXEI | SPI_INT_TXOI | SPI_INT_RXUI | SPI_INT_RXOI; | |
| dws->transfer_handler = interrupt_transfer; | |
| } | |
| /* | |
| * Reprogram registers only if | |
| * 1. chip select changes | |
| * 2. clk_div is changed | |
| * 3. control value changes | |
| */ | |
| if (dw_readw(dws, ctrl0) != cr0 || cs_change || clk_div || imask) { | |
| spi_enable_chip(dws, 0); | |
| if (dw_readw(dws, ctrl0) != cr0) | |
| dw_writew(dws, ctrl0, cr0); | |
| spi_set_clk(dws, clk_div ? clk_div : chip->clk_div); | |
| spi_chip_sel(dws, spi->chip_select); | |
| /* Set the interrupt mask, for poll mode just disable all int */ | |
| spi_mask_intr(dws, 0xff); | |
| if (imask) | |
| spi_umask_intr(dws, imask); | |
| if (txint_level) | |
| dw_writew(dws, txfltr, txint_level); | |
| spi_enable_chip(dws, 1); | |
| if (cs_change) | |
| dws->prev_chip = chip; | |
| } | |
| if (dws->dma_mapped) | |
| dws->dma_ops->dma_transfer(dws, cs_change); | |
| if (chip->poll_mode) | |
| poll_transfer(dws); | |
| return; | |
| early_exit: | |
| giveback(dws); | |
| return; | |
| } | |
| static void pump_messages(struct work_struct *work) | |
| { | |
| struct dw_spi *dws = | |
| container_of(work, struct dw_spi, pump_messages); | |
| unsigned long flags; | |
| /* Lock queue and check for queue work */ | |
| spin_lock_irqsave(&dws->lock, flags); | |
| if (list_empty(&dws->queue) || dws->run == QUEUE_STOPPED) { | |
| dws->busy = 0; | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| return; | |
| } | |
| /* Make sure we are not already running a message */ | |
| if (dws->cur_msg) { | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| return; | |
| } | |
| /* Extract head of queue */ | |
| dws->cur_msg = list_entry(dws->queue.next, struct spi_message, queue); | |
| list_del_init(&dws->cur_msg->queue); | |
| /* Initial message state*/ | |
| dws->cur_msg->state = START_STATE; | |
| dws->cur_transfer = list_entry(dws->cur_msg->transfers.next, | |
| struct spi_transfer, | |
| transfer_list); | |
| dws->cur_chip = spi_get_ctldata(dws->cur_msg->spi); | |
| /* Mark as busy and launch transfers */ | |
| tasklet_schedule(&dws->pump_transfers); | |
| dws->busy = 1; | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| } | |
| /* spi_device use this to queue in their spi_msg */ | |
| static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg) | |
| { | |
| struct dw_spi *dws = spi_master_get_devdata(spi->master); | |
| unsigned long flags; | |
| spin_lock_irqsave(&dws->lock, flags); | |
| if (dws->run == QUEUE_STOPPED) { | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| return -ESHUTDOWN; | |
| } | |
| msg->actual_length = 0; | |
| msg->status = -EINPROGRESS; | |
| msg->state = START_STATE; | |
| list_add_tail(&msg->queue, &dws->queue); | |
| if (dws->run == QUEUE_RUNNING && !dws->busy) { | |
| if (dws->cur_transfer || dws->cur_msg) | |
| queue_work(dws->workqueue, | |
| &dws->pump_messages); | |
| else { | |
| /* If no other data transaction in air, just go */ | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| pump_messages(&dws->pump_messages); | |
| return 0; | |
| } | |
| } | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| return 0; | |
| } | |
| /* This may be called twice for each spi dev */ | |
| static int dw_spi_setup(struct spi_device *spi) | |
| { | |
| struct dw_spi_chip *chip_info = NULL; | |
| struct chip_data *chip; | |
| if (spi->bits_per_word != 8 && spi->bits_per_word != 16) | |
| return -EINVAL; | |
| /* Only alloc on first setup */ | |
| chip = spi_get_ctldata(spi); | |
| if (!chip) { | |
| chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); | |
| if (!chip) | |
| return -ENOMEM; | |
| } | |
| /* | |
| * Protocol drivers may change the chip settings, so... | |
| * if chip_info exists, use it | |
| */ | |
| chip_info = spi->controller_data; | |
| /* chip_info doesn't always exist */ | |
| if (chip_info) { | |
| if (chip_info->cs_control) | |
| chip->cs_control = chip_info->cs_control; | |
| chip->poll_mode = chip_info->poll_mode; | |
| chip->type = chip_info->type; | |
| chip->rx_threshold = 0; | |
| chip->tx_threshold = 0; | |
| chip->enable_dma = chip_info->enable_dma; | |
| } | |
| if (spi->bits_per_word <= 8) { | |
| chip->n_bytes = 1; | |
| chip->dma_width = 1; | |
| } else if (spi->bits_per_word <= 16) { | |
| chip->n_bytes = 2; | |
| chip->dma_width = 2; | |
| } else { | |
| /* Never take >16b case for MRST SPIC */ | |
| dev_err(&spi->dev, "invalid wordsize\n"); | |
| return -EINVAL; | |
| } | |
| chip->bits_per_word = spi->bits_per_word; | |
| if (!spi->max_speed_hz) { | |
| dev_err(&spi->dev, "No max speed HZ parameter\n"); | |
| return -EINVAL; | |
| } | |
| chip->speed_hz = spi->max_speed_hz; | |
| chip->tmode = 0; /* Tx & Rx */ | |
| /* Default SPI mode is SCPOL = 0, SCPH = 0 */ | |
| chip->cr0 = (chip->bits_per_word - 1) | |
| | (chip->type << SPI_FRF_OFFSET) | |
| | (spi->mode << SPI_MODE_OFFSET) | |
| | (chip->tmode << SPI_TMOD_OFFSET); | |
| spi_set_ctldata(spi, chip); | |
| return 0; | |
| } | |
| static void dw_spi_cleanup(struct spi_device *spi) | |
| { | |
| struct chip_data *chip = spi_get_ctldata(spi); | |
| kfree(chip); | |
| } | |
| static int __devinit init_queue(struct dw_spi *dws) | |
| { | |
| INIT_LIST_HEAD(&dws->queue); | |
| spin_lock_init(&dws->lock); | |
| dws->run = QUEUE_STOPPED; | |
| dws->busy = 0; | |
| tasklet_init(&dws->pump_transfers, | |
| pump_transfers, (unsigned long)dws); | |
| INIT_WORK(&dws->pump_messages, pump_messages); | |
| dws->workqueue = create_singlethread_workqueue( | |
| dev_name(dws->master->dev.parent)); | |
| if (dws->workqueue == NULL) | |
| return -EBUSY; | |
| return 0; | |
| } | |
| static int start_queue(struct dw_spi *dws) | |
| { | |
| unsigned long flags; | |
| spin_lock_irqsave(&dws->lock, flags); | |
| if (dws->run == QUEUE_RUNNING || dws->busy) { | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| return -EBUSY; | |
| } | |
| dws->run = QUEUE_RUNNING; | |
| dws->cur_msg = NULL; | |
| dws->cur_transfer = NULL; | |
| dws->cur_chip = NULL; | |
| dws->prev_chip = NULL; | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| queue_work(dws->workqueue, &dws->pump_messages); | |
| return 0; | |
| } | |
| static int stop_queue(struct dw_spi *dws) | |
| { | |
| unsigned long flags; | |
| unsigned limit = 50; | |
| int status = 0; | |
| spin_lock_irqsave(&dws->lock, flags); | |
| dws->run = QUEUE_STOPPED; | |
| while ((!list_empty(&dws->queue) || dws->busy) && limit--) { | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| msleep(10); | |
| spin_lock_irqsave(&dws->lock, flags); | |
| } | |
| if (!list_empty(&dws->queue) || dws->busy) | |
| status = -EBUSY; | |
| spin_unlock_irqrestore(&dws->lock, flags); | |
| return status; | |
| } | |
| static int destroy_queue(struct dw_spi *dws) | |
| { | |
| int status; | |
| status = stop_queue(dws); | |
| if (status != 0) | |
| return status; | |
| destroy_workqueue(dws->workqueue); | |
| return 0; | |
| } | |
| /* Restart the controller, disable all interrupts, clean rx fifo */ | |
| static void spi_hw_init(struct dw_spi *dws) | |
| { | |
| spi_enable_chip(dws, 0); | |
| spi_mask_intr(dws, 0xff); | |
| spi_enable_chip(dws, 1); | |
| /* | |
| * Try to detect the FIFO depth if not set by interface driver, | |
| * the depth could be from 2 to 256 from HW spec | |
| */ | |
| if (!dws->fifo_len) { | |
| u32 fifo; | |
| for (fifo = 2; fifo <= 257; fifo++) { | |
| dw_writew(dws, txfltr, fifo); | |
| if (fifo != dw_readw(dws, txfltr)) | |
| break; | |
| } | |
| dws->fifo_len = (fifo == 257) ? 0 : fifo; | |
| dw_writew(dws, txfltr, 0); | |
| } | |
| } | |
| int __devinit dw_spi_add_host(struct dw_spi *dws) | |
| { | |
| struct spi_master *master; | |
| int ret; | |
| BUG_ON(dws == NULL); | |
| master = spi_alloc_master(dws->parent_dev, 0); | |
| if (!master) { | |
| ret = -ENOMEM; | |
| goto exit; | |
| } | |
| dws->master = master; | |
| dws->type = SSI_MOTO_SPI; | |
| dws->prev_chip = NULL; | |
| dws->dma_inited = 0; | |
| dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60); | |
| ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, | |
| "dw_spi", dws); | |
| if (ret < 0) { | |
| dev_err(&master->dev, "can not get IRQ\n"); | |
| goto err_free_master; | |
| } | |
| master->mode_bits = SPI_CPOL | SPI_CPHA; | |
| master->bus_num = dws->bus_num; | |
| master->num_chipselect = dws->num_cs; | |
| master->cleanup = dw_spi_cleanup; | |
| master->setup = dw_spi_setup; | |
| master->transfer = dw_spi_transfer; | |
| /* Basic HW init */ | |
| spi_hw_init(dws); | |
| if (dws->dma_ops && dws->dma_ops->dma_init) { | |
| ret = dws->dma_ops->dma_init(dws); | |
| if (ret) { | |
| dev_warn(&master->dev, "DMA init failed\n"); | |
| dws->dma_inited = 0; | |
| } | |
| } | |
| /* Initial and start queue */ | |
| ret = init_queue(dws); | |
| if (ret) { | |
| dev_err(&master->dev, "problem initializing queue\n"); | |
| goto err_diable_hw; | |
| } | |
| ret = start_queue(dws); | |
| if (ret) { | |
| dev_err(&master->dev, "problem starting queue\n"); | |
| goto err_diable_hw; | |
| } | |
| spi_master_set_devdata(master, dws); | |
| ret = spi_register_master(master); | |
| if (ret) { | |
| dev_err(&master->dev, "problem registering spi master\n"); | |
| goto err_queue_alloc; | |
| } | |
| mrst_spi_debugfs_init(dws); | |
| return 0; | |
| err_queue_alloc: | |
| destroy_queue(dws); | |
| if (dws->dma_ops && dws->dma_ops->dma_exit) | |
| dws->dma_ops->dma_exit(dws); | |
| err_diable_hw: | |
| spi_enable_chip(dws, 0); | |
| free_irq(dws->irq, dws); | |
| err_free_master: | |
| spi_master_put(master); | |
| exit: | |
| return ret; | |
| } | |
| EXPORT_SYMBOL_GPL(dw_spi_add_host); | |
| void __devexit dw_spi_remove_host(struct dw_spi *dws) | |
| { | |
| int status = 0; | |
| if (!dws) | |
| return; | |
| mrst_spi_debugfs_remove(dws); | |
| /* Remove the queue */ | |
| status = destroy_queue(dws); | |
| if (status != 0) | |
| dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not " | |
| "complete, message memory not freed\n"); | |
| if (dws->dma_ops && dws->dma_ops->dma_exit) | |
| dws->dma_ops->dma_exit(dws); | |
| spi_enable_chip(dws, 0); | |
| /* Disable clk */ | |
| spi_set_clk(dws, 0); | |
| free_irq(dws->irq, dws); | |
| /* Disconnect from the SPI framework */ | |
| spi_unregister_master(dws->master); | |
| } | |
| EXPORT_SYMBOL_GPL(dw_spi_remove_host); | |
| int dw_spi_suspend_host(struct dw_spi *dws) | |
| { | |
| int ret = 0; | |
| ret = stop_queue(dws); | |
| if (ret) | |
| return ret; | |
| spi_enable_chip(dws, 0); | |
| spi_set_clk(dws, 0); | |
| return ret; | |
| } | |
| EXPORT_SYMBOL_GPL(dw_spi_suspend_host); | |
| int dw_spi_resume_host(struct dw_spi *dws) | |
| { | |
| int ret; | |
| spi_hw_init(dws); | |
| ret = start_queue(dws); | |
| if (ret) | |
| dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret); | |
| return ret; | |
| } | |
| EXPORT_SYMBOL_GPL(dw_spi_resume_host); | |
| MODULE_AUTHOR("Feng Tang <feng.tang@intel.com>"); | |
| MODULE_DESCRIPTION("Driver for DesignWare SPI controller core"); | |
| MODULE_LICENSE("GPL v2"); |