| # SPDX-License-Identifier: GPL-2.0-only | |
| # | |
| # Multimedia Video device configuration | |
| # | |
| if VIDEO_DEV | |
| comment "IR I2C driver auto-selected by 'Autoselect ancillary drivers'" | |
| depends on MEDIA_SUBDRV_AUTOSELECT && I2C && RC_CORE | |
| config VIDEO_IR_I2C | |
| tristate "I2C module for IR" if !MEDIA_SUBDRV_AUTOSELECT || EXPERT | |
| depends on I2C && RC_CORE | |
| default y | |
| help | |
| Most boards have an IR chip directly connected via GPIO. However, | |
| some video boards have the IR connected via I2C bus. | |
| If your board doesn't have an I2C IR chip, you may disable this | |
| option. | |
| In doubt, say Y. | |
| # | |
| # V4L2 I2C drivers that are related with Camera support | |
| # | |
| menuconfig VIDEO_CAMERA_SENSOR | |
| bool "Camera sensor devices" | |
| depends on MEDIA_CAMERA_SUPPORT && I2C && HAVE_CLK | |
| select MEDIA_CONTROLLER | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| default y | |
| if VIDEO_CAMERA_SENSOR | |
| config VIDEO_APTINA_PLL | |
| tristate | |
| config VIDEO_CCS_PLL | |
| tristate | |
| config VIDEO_ALVIUM_CSI2 | |
| tristate "Allied Vision ALVIUM MIPI CSI-2 camera support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor-level driver for the Allied Vision | |
| ALVIUM camera connected via MIPI CSI-2 interface. | |
| To compile this driver as a module, choose M here: the | |
| module will be called alvium-csi2. | |
| config VIDEO_AR0521 | |
| tristate "ON Semiconductor AR0521 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the ON Semiconductor | |
| AR0521 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ar0521. | |
| config VIDEO_GC0308 | |
| tristate "GalaxyCore GC0308 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the GalaxyCore | |
| GC0308 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called gc0308. | |
| config VIDEO_GC0310 | |
| tristate "GalaxyCore GC0310 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor-level driver for the Galaxycore | |
| GC0310 0.3MP sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called gc0310. | |
| config VIDEO_GC05A2 | |
| tristate "GalaxyCore gc05a2 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the GalaxyCore gc05a2 | |
| camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called gc05a2. | |
| config VIDEO_GC08A3 | |
| tristate "GalaxyCore gc08a3 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the GalaxyCore gc08a3 | |
| camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called gc08a3. | |
| config VIDEO_GC2145 | |
| select V4L2_CCI_I2C | |
| tristate "GalaxyCore GC2145 sensor support" | |
| help | |
| This is a V4L2 sensor-level driver for GalaxyCore GC2145 | |
| 2 Mpixel camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called gc2145. | |
| config VIDEO_HI556 | |
| tristate "Hynix Hi-556 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Hynix | |
| Hi-556 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called hi556. | |
| config VIDEO_HI846 | |
| tristate "Hynix Hi-846 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Hynix | |
| Hi-846 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called hi846. | |
| config VIDEO_HI847 | |
| tristate "Hynix Hi-847 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Hynix | |
| Hi-847 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called hi847. | |
| config VIDEO_IMX111 | |
| tristate "Sony IMX111 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a V4L2 sensor driver for the Sony IMX111 camera | |
| sensors. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx111. | |
| config VIDEO_IMX208 | |
| tristate "Sony IMX208 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX208 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx208. | |
| config VIDEO_IMX214 | |
| tristate "Sony IMX214 sensor support" | |
| depends on GPIOLIB | |
| select REGMAP_I2C | |
| select V4L2_CCI_I2C | |
| select VIDEO_CCS_PLL | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX214 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx214. | |
| config VIDEO_IMX219 | |
| tristate "Sony IMX219 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX219 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx219. | |
| config VIDEO_IMX258 | |
| tristate "Sony IMX258 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX258 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx258. | |
| config VIDEO_IMX274 | |
| tristate "Sony IMX274 sensor support" | |
| select REGMAP_I2C | |
| help | |
| This is a V4L2 sensor driver for the Sony IMX274 | |
| CMOS image sensor. | |
| config VIDEO_IMX283 | |
| tristate "Sony IMX283 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a V4L2 sensor driver for the Sony IMX283 | |
| CMOS image sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx283. | |
| config VIDEO_IMX290 | |
| tristate "Sony IMX290 sensor support" | |
| select REGMAP_I2C | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX290 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx290. | |
| config VIDEO_IMX296 | |
| tristate "Sony IMX296 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX296 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx296. | |
| config VIDEO_IMX319 | |
| tristate "Sony IMX319 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX319 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx319. | |
| config VIDEO_IMX334 | |
| tristate "Sony IMX334 sensor support" | |
| depends on OF | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX334 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx334. | |
| config VIDEO_IMX335 | |
| tristate "Sony IMX335 sensor support" | |
| depends on OF | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX335 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx335. | |
| config VIDEO_IMX355 | |
| tristate "Sony IMX355 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX355 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx355. | |
| config VIDEO_IMX412 | |
| tristate "Sony IMX412 sensor support" | |
| depends on OF | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX412 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx412. | |
| config VIDEO_IMX415 | |
| tristate "Sony IMX415 sensor support" | |
| depends on OF | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX415 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx415. | |
| config VIDEO_IMX471 | |
| tristate "Sony IMX471 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX471 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx471. | |
| config VIDEO_IMX678 | |
| tristate "Sony IMX678 sensor support" | |
| depends on GPIOLIB | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Sony | |
| IMX678 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called imx678. | |
| config VIDEO_MAX9271_LIB | |
| tristate | |
| config VIDEO_MT9M001 | |
| tristate "mt9m001 support" | |
| help | |
| This driver supports MT9M001 cameras from Micron, monochrome | |
| and colour models. | |
| config VIDEO_MT9M111 | |
| tristate "mt9m111, mt9m112 and mt9m131 support" | |
| help | |
| This driver supports MT9M111, MT9M112 and MT9M131 cameras from | |
| Micron/Aptina | |
| config VIDEO_MT9M114 | |
| tristate "onsemi MT9M114 sensor support" | |
| select V4L2_CCI_I2C | |
| select VIDEO_APTINA_PLL | |
| help | |
| This is a Video4Linux2 sensor-level driver for the onsemi MT9M114 | |
| camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called mt9m114. | |
| config VIDEO_MT9P031 | |
| tristate "Aptina MT9P031 support" | |
| select VIDEO_APTINA_PLL | |
| help | |
| This is a Video4Linux2 sensor driver for the Aptina | |
| (Micron) mt9p031 5 Mpixel camera. | |
| config VIDEO_MT9T112 | |
| tristate "Aptina MT9T111/MT9T112 support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Aptina | |
| (Micron) MT9T111 and MT9T112 3 Mpixel camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called mt9t112. | |
| config VIDEO_MT9V011 | |
| tristate "Micron mt9v011 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Micron | |
| mt0v011 1.3 Mpixel camera. It currently only works with the | |
| em28xx driver. | |
| config VIDEO_MT9V032 | |
| tristate "Micron MT9V032 sensor support" | |
| depends on OF | |
| select REGMAP_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Micron | |
| MT9V032 752x480 CMOS sensor. | |
| config VIDEO_MT9V111 | |
| tristate "Aptina MT9V111 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the Aptina/Micron | |
| MT9V111 sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called mt9v111. | |
| config VIDEO_OG01A1B | |
| tristate "OmniVision OG01A1B sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OG01A1B camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called og01a1b. | |
| config VIDEO_OG0VE1B | |
| tristate "OmniVision OG0VE1B sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OG0VE1B camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called og0ve1b. | |
| config VIDEO_OS05B10 | |
| tristate "OmniVision OS05B10 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for Omnivision | |
| OS05B10 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called os05b10. | |
| config VIDEO_OV01A10 | |
| tristate "OmniVision OV01A10 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV01A10 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov01a10. | |
| config VIDEO_OV02A10 | |
| tristate "OmniVision OV02A10 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV02A10 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov02a10. | |
| config VIDEO_OV02E10 | |
| tristate "OmniVision OV02E10 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV02E10 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov02e10. | |
| config VIDEO_OV02C10 | |
| tristate "OmniVision OV02C10 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV02C10 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov02c10. | |
| config VIDEO_OV08D10 | |
| tristate "OmniVision OV08D10 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV08D10 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov08d10. | |
| config VIDEO_OV08X40 | |
| tristate "OmniVision OV08X40 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV08X40 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov08x40. | |
| config VIDEO_OV13858 | |
| tristate "OmniVision OV13858 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV13858 camera. | |
| config VIDEO_OV13B10 | |
| tristate "OmniVision OV13B10 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV13B10 camera. | |
| config VIDEO_OV2640 | |
| tristate "OmniVision OV2640 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2640 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2640. | |
| config VIDEO_OV2659 | |
| tristate "OmniVision OV2659 sensor support" | |
| depends on GPIOLIB | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2659 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2659. | |
| config VIDEO_OV2680 | |
| tristate "OmniVision OV2680 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2680 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2680. | |
| config VIDEO_OV2685 | |
| tristate "OmniVision OV2685 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2685 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2685. | |
| config VIDEO_OV2732 | |
| tristate "OmniVision OV2732 sensor support" | |
| depends on OF | |
| select MEDIA_CONTROLLER | |
| select V4L2_CCI_I2C | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2732 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2732. | |
| config VIDEO_OV2735 | |
| tristate "OmniVision OV2735 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2735 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2735. | |
| config VIDEO_OV2740 | |
| tristate "OmniVision OV2740 sensor support" | |
| depends on ACPI || COMPILE_TEST | |
| select REGMAP_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV2740 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov2740. | |
| config VIDEO_OV4689 | |
| tristate "OmniVision OV4689 sensor support" | |
| depends on GPIOLIB | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor-level driver for the OmniVision | |
| OV4689 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov4689. | |
| config VIDEO_OV5640 | |
| tristate "OmniVision OV5640 sensor support" | |
| depends on OF | |
| depends on GPIOLIB | |
| help | |
| This is a Video4Linux2 sensor driver for the Omnivision | |
| OV5640 camera sensor with a MIPI CSI-2 interface. | |
| config VIDEO_OV5645 | |
| tristate "OmniVision OV5645 sensor support" | |
| depends on OF | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5645 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5645. | |
| config VIDEO_OV5647 | |
| tristate "OmniVision OV5647 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5647 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5647. | |
| config VIDEO_OV5648 | |
| tristate "OmniVision OV5648 sensor support" | |
| depends on PM | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5648 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5648. | |
| config VIDEO_OV5670 | |
| tristate "OmniVision OV5670 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5670 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5670. | |
| config VIDEO_OV5675 | |
| tristate "OmniVision OV5675 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5675 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5675. | |
| config VIDEO_OV5693 | |
| tristate "OmniVision OV5693 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5693 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5693. | |
| config VIDEO_OV5695 | |
| tristate "OmniVision OV5695 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV5695 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov5695. | |
| config VIDEO_OV6211 | |
| tristate "OmniVision OV6211 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV6211 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov6211. | |
| config VIDEO_OV64A40 | |
| tristate "OmniVision OV64A40 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV64A40 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov64a40. | |
| config VIDEO_OV7251 | |
| tristate "OmniVision OV7251 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV7251 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov7251. | |
| config VIDEO_OV7640 | |
| tristate "OmniVision OV7640 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV7640 camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov7640. | |
| config VIDEO_OV7670 | |
| tristate "OmniVision OV7670 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV7670 VGA camera. It currently only works with the M88ALP01 | |
| controller. | |
| config VIDEO_OV772X | |
| tristate "OmniVision OV772x sensor support" | |
| select REGMAP_SCCB | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV772x camera. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov772x. | |
| config VIDEO_OV7740 | |
| tristate "OmniVision OV7740 sensor support" | |
| select REGMAP_SCCB | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV7740 VGA camera sensor. | |
| config VIDEO_OV8856 | |
| tristate "OmniVision OV8856 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV8856 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov8856. | |
| config VIDEO_OV8858 | |
| tristate "OmniVision OV8858 sensor support" | |
| depends on PM | |
| help | |
| This is a Video4Linux2 sensor driver for OmniVision | |
| OV8858 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov8858. | |
| config VIDEO_OV8865 | |
| tristate "OmniVision OV8865 sensor support" | |
| depends on PM | |
| help | |
| This is a Video4Linux2 sensor driver for OmniVision | |
| OV8865 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov8865. | |
| config VIDEO_OV9282 | |
| tristate "OmniVision OV9282 sensor support" | |
| depends on OF | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV9282 camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ov9282. | |
| config VIDEO_OV9640 | |
| tristate "OmniVision OV9640 sensor support" | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV9640 camera sensor. | |
| config VIDEO_OV9650 | |
| tristate "OmniVision OV9650/OV9652 sensor support" | |
| select REGMAP_SCCB | |
| help | |
| This is a V4L2 sensor driver for the Omnivision | |
| OV9650 and OV9652 camera sensors. | |
| config VIDEO_OV9734 | |
| tristate "OmniVision OV9734 sensor support" | |
| depends on ACPI || COMPILE_TEST | |
| help | |
| This is a Video4Linux2 sensor driver for the OmniVision | |
| OV9734 camera. | |
| To compile this driver as a module, choose M here: the | |
| module's name is ov9734. | |
| config VIDEO_RDACM20 | |
| tristate "IMI RDACM20 camera support" | |
| select VIDEO_MAX9271_LIB | |
| help | |
| This driver supports the IMI RDACM20 GMSL camera, used in | |
| ADAS systems. | |
| This camera should be used in conjunction with a GMSL | |
| deserialiser such as the MAX9286. | |
| config VIDEO_RDACM21 | |
| tristate "IMI RDACM21 camera support" | |
| select VIDEO_MAX9271_LIB | |
| help | |
| This driver supports the IMI RDACM21 GMSL camera, used in | |
| ADAS systems. | |
| This camera should be used in conjunction with a GMSL | |
| deserialiser such as the MAX9286. | |
| config VIDEO_RJ54N1 | |
| tristate "Sharp RJ54N1CB0C sensor support" | |
| help | |
| This is a V4L2 sensor driver for Sharp RJ54N1CB0C CMOS image | |
| sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called rj54n1. | |
| config VIDEO_S5C73M3 | |
| tristate "Samsung S5C73M3 sensor support" | |
| depends on SPI | |
| help | |
| This is a V4L2 sensor driver for Samsung S5C73M3 | |
| 8 Mpixel camera. | |
| config VIDEO_S5K3M5 | |
| tristate "Samsung S5K3M5 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a V4L2 sensor driver for Samsung S5K3M5 13MP raw | |
| camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called s5k3m5. | |
| config VIDEO_S5K5BAF | |
| tristate "Samsung S5K5BAF sensor support" | |
| help | |
| This is a V4L2 sensor driver for Samsung S5K5BAF 2M | |
| camera sensor with an embedded SoC image signal processor. | |
| config VIDEO_S5K6A3 | |
| tristate "Samsung S5K6A3 sensor support" | |
| help | |
| This is a V4L2 sensor driver for Samsung S5K6A3 raw | |
| camera sensor. | |
| config VIDEO_S5KJN1 | |
| tristate "Samsung S5KJN1 sensor support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a V4L2 sensor driver for Samsung S5KJN1 50MP raw | |
| camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called s5kjn1. | |
| config VIDEO_T4KA3 | |
| tristate "Toshiba T4KA3 sensor support" | |
| depends on ACPI || COMPILE_TEST | |
| depends on GPIOLIB | |
| select V4L2_CCI_I2C | |
| help | |
| This is a Video4Linux2 sensor driver for the Toshiba T4KA3 8 MP | |
| camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called t4ka3. | |
| config VIDEO_VD55G1 | |
| tristate "ST VD55G1 sensor support" | |
| select V4L2_CCI_I2C | |
| depends on GPIOLIB | |
| help | |
| This is a Video4Linux2 sensor driver for the ST VD55G1 | |
| camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called vd55g1. | |
| config VIDEO_VD56G3 | |
| tristate "ST VD56G3 sensor support" | |
| select V4L2_CCI_I2C | |
| depends on GPIOLIB | |
| help | |
| This is a Video4Linux2 sensor driver for the ST VD56G3 | |
| camera sensor. | |
| To compile this driver as a module, choose M here: the | |
| module will be called vd56g3. | |
| config VIDEO_VGXY61 | |
| tristate "ST VGXY61 sensor support" | |
| select V4L2_CCI_I2C | |
| depends on OF && GPIOLIB | |
| help | |
| This is a Video4Linux2 sensor driver for the ST VGXY61 | |
| camera sensor. | |
| source "drivers/media/i2c/ccs/Kconfig" | |
| source "drivers/media/i2c/et8ek8/Kconfig" | |
| endif | |
| menu "Camera ISPs" | |
| visible if MEDIA_CAMERA_SUPPORT | |
| config VIDEO_THP7312 | |
| tristate "THine THP7312 support" | |
| depends on I2C | |
| select FW_LOADER | |
| select FW_UPLOAD | |
| select MEDIA_CONTROLLER | |
| select V4L2_CCI_I2C | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| This is a Video4Linux2 sensor-level driver for the THine | |
| THP7312 ISP. | |
| endmenu | |
| menuconfig VIDEO_CAMERA_LENS | |
| bool "Lens drivers" | |
| depends on MEDIA_CAMERA_SUPPORT && I2C | |
| select MEDIA_CONTROLLER | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| default y | |
| if VIDEO_CAMERA_LENS | |
| config VIDEO_AD5820 | |
| tristate "AD5820 lens voice coil support" | |
| depends on GPIOLIB | |
| help | |
| This is a driver for the AD5820 camera lens voice coil. | |
| It is used for example in Nokia N900 (RX-51). | |
| config VIDEO_AK7375 | |
| tristate "AK7375 lens voice coil support" | |
| help | |
| This is a driver for the AK7375 camera lens voice coil. | |
| AK7375 is a 12 bit DAC with 120mA output current sink | |
| capability. This is designed for linear control of | |
| voice coil motors, controlled via I2C serial interface. | |
| config VIDEO_DW9714 | |
| tristate "DW9714 lens voice coil support" | |
| depends on GPIOLIB | |
| help | |
| This is a driver for the DW9714 camera lens voice coil. | |
| DW9714 is a 10 bit DAC with 120mA output current sink | |
| capability. This is designed for linear control of | |
| voice coil motors, controlled via I2C serial interface. | |
| config VIDEO_DW9719 | |
| tristate "DW9719 lens voice coil support" | |
| select V4L2_CCI_I2C | |
| help | |
| This is a driver for the DW9719 camera lens voice coil. | |
| This is designed for linear control of voice coil motors, | |
| controlled via I2C serial interface. | |
| config VIDEO_DW9768 | |
| tristate "DW9768 lens voice coil support" | |
| help | |
| This is a driver for the DW9768 camera lens voice coil. | |
| DW9768 is a 10 bit DAC with 100mA output current sink | |
| capability. This is designed for linear control of | |
| voice coil motors, controlled via I2C serial interface. | |
| config VIDEO_DW9807_VCM | |
| tristate "DW9807 lens voice coil support" | |
| help | |
| This is a driver for the DW9807 camera lens voice coil. | |
| DW9807 is a 10 bit DAC with 100mA output current sink | |
| capability. This is designed for linear control of | |
| voice coil motors, controlled via I2C serial interface. | |
| endif | |
| menu "Flash devices" | |
| visible if MEDIA_CAMERA_SUPPORT | |
| config VIDEO_ADP1653 | |
| tristate "ADP1653 flash support" | |
| depends on I2C && VIDEO_DEV | |
| select MEDIA_CONTROLLER | |
| select V4L2_ASYNC | |
| help | |
| This is a driver for the ADP1653 flash controller. It is used for | |
| example in Nokia N900. | |
| config VIDEO_LM3560 | |
| tristate "LM3560 dual flash driver support" | |
| depends on I2C && VIDEO_DEV | |
| select MEDIA_CONTROLLER | |
| select REGMAP_I2C | |
| select V4L2_ASYNC | |
| help | |
| This is a driver for the lm3560 dual flash controllers. It controls | |
| flash, torch LEDs. | |
| config VIDEO_LM3646 | |
| tristate "LM3646 dual flash driver support" | |
| depends on I2C && VIDEO_DEV | |
| select MEDIA_CONTROLLER | |
| select REGMAP_I2C | |
| select V4L2_ASYNC | |
| help | |
| This is a driver for the lm3646 dual flash controllers. It controls | |
| flash, torch LEDs. | |
| endmenu | |
| # | |
| # V4L2 I2C drivers that aren't related with Camera support | |
| # | |
| comment "audio, video and radio I2C drivers auto-selected by 'Autoselect ancillary drivers'" | |
| depends on MEDIA_HIDE_ANCILLARY_SUBDRV | |
| # | |
| # Encoder / Decoder module configuration | |
| # | |
| menu "Audio decoders, processors and mixers" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config VIDEO_CS3308 | |
| tristate "Cirrus Logic CS3308 audio ADC" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Cirrus Logic CS3308 High Performance 8-Channel | |
| Analog Volume Control | |
| To compile this driver as a module, choose M here: the | |
| module will be called cs3308. | |
| config VIDEO_CS5345 | |
| tristate "Cirrus Logic CS5345 audio ADC" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Cirrus Logic CS5345 24-bit, 192 kHz | |
| stereo A/D converter. | |
| To compile this driver as a module, choose M here: the | |
| module will be called cs5345. | |
| config VIDEO_CS53L32A | |
| tristate "Cirrus Logic CS53L32A audio ADC" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Cirrus Logic CS53L32A low voltage | |
| stereo A/D converter. | |
| To compile this driver as a module, choose M here: the | |
| module will be called cs53l32a. | |
| config VIDEO_MSP3400 | |
| tristate "Micronas MSP34xx audio decoders" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Micronas MSP34xx series of audio decoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called msp3400. | |
| config VIDEO_SONY_BTF_MPX | |
| tristate "Sony BTF's internal MPX" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the internal MPX of the Sony BTF-PG472Z tuner. | |
| To compile this driver as a module, choose M here: the | |
| module will be called sony-btf-mpx. | |
| config VIDEO_TDA1997X | |
| tristate "NXP TDA1997x HDMI receiver" | |
| depends on VIDEO_DEV && I2C | |
| depends on SND_SOC | |
| select HDMI | |
| select SND_PCM | |
| select V4L2_FWNODE | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| V4L2 subdevice driver for the NXP TDA1997x HDMI receivers. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tda1997x. | |
| config VIDEO_TDA7432 | |
| tristate "Philips TDA7432 audio processor" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for tda7432 audio decoder chip found on some bt8xx boards. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tda7432. | |
| config VIDEO_TDA9840 | |
| tristate "Philips TDA9840 audio processor" | |
| depends on I2C | |
| help | |
| Support for tda9840 audio decoder chip found on some Zoran boards. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tda9840. | |
| config VIDEO_TEA6415C | |
| tristate "Philips TEA6415C audio processor" | |
| depends on I2C | |
| help | |
| Support for tea6415c audio decoder chip found on some bt8xx boards. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tea6415c. | |
| config VIDEO_TEA6420 | |
| tristate "Philips TEA6420 audio processor" | |
| depends on I2C | |
| help | |
| Support for tea6420 audio decoder chip found on some bt8xx boards. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tea6420. | |
| config VIDEO_TLV320AIC23B | |
| tristate "Texas Instruments TLV320AIC23B audio codec" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Texas Instruments TLV320AIC23B audio codec. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tlv320aic23b. | |
| config VIDEO_TVAUDIO | |
| tristate "Simple audio decoder chips" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for several audio decoder chips found on some bt8xx boards: | |
| Philips: tda9840, tda9873h, tda9874h/a, tda9850, tda985x, tea6300, | |
| tea6320, tea6420, tda8425, ta8874z. | |
| Microchip: pic16c54 based design on ProVideo PV951 board. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tvaudio. | |
| config VIDEO_UDA1342 | |
| tristate "Philips UDA1342 audio codec" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Philips UDA1342 audio codec. | |
| To compile this driver as a module, choose M here: the | |
| module will be called uda1342. | |
| config VIDEO_VP27SMPX | |
| tristate "Panasonic VP27's internal MPX" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the internal MPX of the Panasonic VP27s tuner. | |
| To compile this driver as a module, choose M here: the | |
| module will be called vp27smpx. | |
| config VIDEO_WM8739 | |
| tristate "Wolfson Microelectronics WM8739 stereo audio ADC" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Wolfson Microelectronics WM8739 | |
| stereo A/D Converter. | |
| To compile this driver as a module, choose M here: the | |
| module will be called wm8739. | |
| config VIDEO_WM8775 | |
| tristate "Wolfson Microelectronics WM8775 audio ADC with input mixer" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Wolfson Microelectronics WM8775 high | |
| performance stereo A/D Converter with a 4 channel input mixer. | |
| To compile this driver as a module, choose M here: the | |
| module will be called wm8775. | |
| endmenu | |
| menu "RDS decoders" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config VIDEO_SAA6588 | |
| tristate "SAA6588 Radio Chip RDS decoder support" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for this Radio Data System (RDS) decoder. This allows | |
| seeing radio station identification transmitted using this | |
| standard. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa6588. | |
| endmenu | |
| menu "Video decoders" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config VIDEO_ADV7180 | |
| tristate "Analog Devices ADV7180 decoder" | |
| depends on GPIOLIB && VIDEO_DEV && I2C | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select V4L2_ASYNC | |
| help | |
| Support for the Analog Devices ADV7180 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7180. | |
| config VIDEO_ADV7183 | |
| tristate "Analog Devices ADV7183 decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| V4l2 subdevice driver for the Analog Devices | |
| ADV7183 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7183. | |
| config VIDEO_ADV748X | |
| tristate "Analog Devices ADV748x decoder" | |
| depends on VIDEO_DEV && I2C | |
| depends on OF | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select REGMAP_I2C | |
| select V4L2_FWNODE | |
| help | |
| V4L2 subdevice driver for the Analog Devices | |
| ADV7481 and ADV7482 HDMI/Analog video decoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv748x. | |
| config VIDEO_ADV7604 | |
| tristate "Analog Devices ADV7604 decoder" | |
| depends on VIDEO_DEV && I2C | |
| depends on GPIOLIB || COMPILE_TEST | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select REGMAP_I2C | |
| select HDMI | |
| select V4L2_FWNODE | |
| help | |
| Support for the Analog Devices ADV7604 video decoder. | |
| This is a Analog Devices Component/Graphics Digitizer | |
| with 4:1 Multiplexed HDMI Receiver. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7604. | |
| config VIDEO_ADV7604_CEC | |
| bool "Enable Analog Devices ADV7604 CEC support" | |
| depends on VIDEO_ADV7604 | |
| select CEC_CORE | |
| help | |
| When selected the adv7604 will support the optional | |
| HDMI CEC feature. | |
| config VIDEO_ADV7842 | |
| tristate "Analog Devices ADV7842 decoder" | |
| depends on VIDEO_DEV && I2C | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select HDMI | |
| help | |
| Support for the Analog Devices ADV7842 video decoder. | |
| This is a Analog Devices Component/Graphics/SD Digitizer | |
| with 2:1 Multiplexed HDMI Receiver. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7842. | |
| config VIDEO_ADV7842_CEC | |
| bool "Enable Analog Devices ADV7842 CEC support" | |
| depends on VIDEO_ADV7842 | |
| select CEC_CORE | |
| help | |
| When selected the adv7842 will support the optional | |
| HDMI CEC feature. | |
| config VIDEO_BT819 | |
| tristate "BT819A VideoStream decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for BT819A video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called bt819. | |
| config VIDEO_BT856 | |
| tristate "BT856 VideoStream decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for BT856 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called bt856. | |
| config VIDEO_BT866 | |
| tristate "BT866 VideoStream decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for BT866 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called bt866. | |
| config VIDEO_ISL7998X | |
| tristate "Intersil ISL7998x video decoder" | |
| depends on VIDEO_DEV && I2C | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select V4L2_FWNODE | |
| help | |
| Support for Intersil ISL7998x analog to MIPI-CSI2 or | |
| BT.656 decoder. | |
| config VIDEO_LT6911UXE | |
| tristate "Lontium LT6911UXE decoder" | |
| depends on ACPI && VIDEO_DEV && I2C | |
| select V4L2_FWNODE | |
| select V4L2_CCI_I2C | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| This is a Video4Linux2 sensor-level driver for the Lontium | |
| LT6911UXE HDMI to MIPI CSI-2 bridge. | |
| To compile this driver as a module, choose M here: the | |
| module will be called lt6911uxe. | |
| config VIDEO_KS0127 | |
| tristate "KS0127 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for KS0127 video decoder. | |
| This chip is used on AverMedia AVS6EYES Zoran-based MJPEG | |
| cards. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ks0127. | |
| config VIDEO_MAX9286 | |
| tristate "Maxim MAX9286 GMSL deserializer support" | |
| depends on I2C && I2C_MUX | |
| depends on VIDEO_DEV | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| select MEDIA_CONTROLLER | |
| help | |
| This driver supports the Maxim MAX9286 GMSL deserializer. | |
| To compile this driver as a module, choose M here: the | |
| module will be called max9286. | |
| config VIDEO_ML86V7667 | |
| tristate "OKI ML86V7667 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the OKI Semiconductor ML86V7667 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ml86v7667. | |
| config VIDEO_SAA7110 | |
| tristate "Philips SAA7110 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Philips SAA7110 video decoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa7110. | |
| config VIDEO_SAA711X | |
| tristate "Philips SAA7111/3/4/5 video decoders" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Philips SAA7111/3/4/5 video decoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa7115. | |
| config VIDEO_TC358743 | |
| tristate "Toshiba TC358743 decoder" | |
| depends on VIDEO_DEV && I2C | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select HDMI | |
| select V4L2_FWNODE | |
| help | |
| Support for the Toshiba TC358743 HDMI to MIPI CSI-2 bridge. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tc358743. | |
| config VIDEO_TC358743_CEC | |
| bool "Enable Toshiba TC358743 CEC support" | |
| depends on VIDEO_TC358743 | |
| select CEC_CORE | |
| help | |
| When selected the tc358743 will support the optional | |
| HDMI CEC feature. | |
| config VIDEO_TC358746 | |
| tristate "Toshiba TC358746 parallel-CSI2 bridge" | |
| depends on VIDEO_DEV && PM && I2C | |
| select VIDEO_V4L2_SUBDEV_API | |
| select MEDIA_CONTROLLER | |
| select V4L2_FWNODE | |
| select GENERIC_PHY | |
| select GENERIC_PHY_MIPI_DPHY | |
| select REGMAP_I2C | |
| help | |
| Support for the Toshiba TC358746 parallel to MIPI CSI-2 bridge. | |
| The bridge can work in both directions but currently only the | |
| parallel-in / csi-out path is supported. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tc358746. | |
| config VIDEO_TVP514X | |
| tristate "Texas Instruments TVP514x video decoder" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_FWNODE | |
| help | |
| This is a Video4Linux2 sensor driver for the TI TVP5146/47 | |
| decoder. It is currently working with the TI OMAP3 camera | |
| controller. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tvp514x. | |
| config VIDEO_TVP5150 | |
| tristate "Texas Instruments TVP5150 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_FWNODE | |
| select REGMAP_I2C | |
| help | |
| Support for the Texas Instruments TVP5150 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tvp5150. | |
| config VIDEO_TVP7002 | |
| tristate "Texas Instruments TVP7002 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_FWNODE | |
| help | |
| Support for the Texas Instruments TVP7002 video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tvp7002. | |
| config VIDEO_TW2804 | |
| tristate "Techwell TW2804 multiple video decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Techwell tw2804 multiple video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tw2804. | |
| config VIDEO_TW9900 | |
| tristate "Techwell TW9900 video decoder" | |
| depends on GPIOLIB | |
| depends on VIDEO_DEV && I2C | |
| depends on PM | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select V4L2_ASYNC | |
| help | |
| Support for the Techwell TW9900 multi-standard video decoder. | |
| It supports NTSC, PAL standards with auto-detection features. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tw9900. | |
| config VIDEO_TW9903 | |
| tristate "Techwell TW9903 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Techwell tw9903 multi-standard video decoder | |
| with high quality down scaler. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tw9903. | |
| config VIDEO_TW9906 | |
| tristate "Techwell TW9906 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Techwell tw9906 enhanced multi-standard comb filter | |
| video decoder with YCbCr input support. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tw9906. | |
| config VIDEO_TW9910 | |
| tristate "Techwell TW9910 video decoder" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_ASYNC | |
| help | |
| Support for Techwell TW9910 NTSC/PAL/SECAM video decoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called tw9910. | |
| config VIDEO_VPX3220 | |
| tristate "vpx3220a, vpx3216b & vpx3214c video decoders" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for VPX322x video decoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called vpx3220. | |
| comment "Video and audio decoders" | |
| config VIDEO_SAA717X | |
| tristate "Philips SAA7171/3/4 audio/video decoders" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Philips SAA7171/3/4 audio/video decoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa717x. | |
| source "drivers/media/i2c/cx25840/Kconfig" | |
| endmenu | |
| menu "Video encoders" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config VIDEO_ADV7170 | |
| tristate "Analog Devices ADV7170 video encoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Analog Devices ADV7170 video encoder driver | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7170. | |
| config VIDEO_ADV7175 | |
| tristate "Analog Devices ADV7175 video encoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Analog Devices ADV7175 video encoder driver | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7175. | |
| config VIDEO_ADV7343 | |
| tristate "ADV7343 video encoder" | |
| depends on I2C | |
| select V4L2_ASYNC | |
| help | |
| Support for Analog Devices I2C bus based ADV7343 encoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7343. | |
| config VIDEO_ADV7393 | |
| tristate "ADV7393 video encoder" | |
| depends on I2C | |
| help | |
| Support for Analog Devices I2C bus based ADV7393 encoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7393. | |
| config VIDEO_ADV7511 | |
| tristate "Analog Devices ADV7511 encoder" | |
| depends on VIDEO_DEV && I2C | |
| depends on DRM_I2C_ADV7511=n || COMPILE_TEST | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select HDMI | |
| help | |
| Support for the Analog Devices ADV7511 video encoder. | |
| This is a Analog Devices HDMI transmitter. | |
| To compile this driver as a module, choose M here: the | |
| module will be called adv7511. | |
| config VIDEO_ADV7511_CEC | |
| bool "Enable Analog Devices ADV7511 CEC support" | |
| depends on VIDEO_ADV7511 | |
| select CEC_CORE | |
| help | |
| When selected the adv7511 will support the optional | |
| HDMI CEC feature. | |
| config VIDEO_AK881X | |
| tristate "AK8813/AK8814 video encoders" | |
| depends on I2C | |
| help | |
| Video output driver for AKM AK8813 and AK8814 TV encoders | |
| config VIDEO_SAA7127 | |
| tristate "Philips SAA7127/9 digital video encoders" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Philips SAA7127/9 digital video encoders. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa7127. | |
| config VIDEO_SAA7185 | |
| tristate "Philips SAA7185 video encoder" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Philips SAA7185 video encoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa7185. | |
| config VIDEO_THS8200 | |
| tristate "Texas Instruments THS8200 video encoder" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_ASYNC | |
| help | |
| Support for the Texas Instruments THS8200 video encoder. | |
| To compile this driver as a module, choose M here: the | |
| module will be called ths8200. | |
| endmenu | |
| menu "Video improvement chips" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config VIDEO_UPD64031A | |
| tristate "NEC Electronics uPD64031A Ghost Reduction" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_ASYNC | |
| help | |
| Support for the NEC Electronics uPD64031A Ghost Reduction | |
| video chip. It is most often found in NTSC TV cards made for | |
| Japan and is used to reduce the 'ghosting' effect that can | |
| be present in analog TV broadcasts. | |
| To compile this driver as a module, choose M here: the | |
| module will be called upd64031a. | |
| config VIDEO_UPD64083 | |
| tristate "NEC Electronics uPD64083 3-Dimensional Y/C separation" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the NEC Electronics uPD64083 3-Dimensional Y/C | |
| separation video chip. It is used to improve the quality of | |
| the colors of a composite signal. | |
| To compile this driver as a module, choose M here: the | |
| module will be called upd64083. | |
| endmenu | |
| menu "Audio/Video compression chips" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config VIDEO_SAA6752HS | |
| tristate "Philips SAA6752HS MPEG-2 Audio/Video Encoder" | |
| depends on VIDEO_DEV && I2C | |
| select CRC32 | |
| help | |
| Support for the Philips SAA6752HS MPEG-2 video and MPEG-audio/AC-3 | |
| audio encoder with multiplexer. | |
| To compile this driver as a module, choose M here: the | |
| module will be called saa6752hs. | |
| endmenu | |
| menu "SDR tuner chips" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| config SDR_MAX2175 | |
| tristate "Maxim 2175 RF to Bits tuner" | |
| depends on VIDEO_DEV && MEDIA_SDR_SUPPORT && I2C | |
| select REGMAP_I2C | |
| select V4L2_ASYNC | |
| help | |
| Support for Maxim 2175 tuner. It is an advanced analog/digital | |
| radio receiver with RF-to-Bits front-end designed for SDR solutions. | |
| To compile this driver as a module, choose M here; the | |
| module will be called max2175. | |
| endmenu | |
| menu "Miscellaneous helper chips" | |
| visible if !MEDIA_HIDE_ANCILLARY_SUBDRV | |
| source "drivers/media/i2c/cvs/Kconfig" | |
| config VIDEO_I2C | |
| tristate "I2C transport video support" | |
| depends on VIDEO_DEV && I2C | |
| select VIDEOBUF2_VMALLOC | |
| imply HWMON | |
| help | |
| Enable the I2C transport video support which supports the | |
| following: | |
| * Panasonic AMG88xx Grid-Eye Sensors | |
| * Melexis MLX90640 Thermal Cameras | |
| To compile this driver as a module, choose M here: the | |
| module will be called video-i2c | |
| config VIDEO_M52790 | |
| tristate "Mitsubishi M52790 A/V switch" | |
| depends on VIDEO_DEV && I2C | |
| help | |
| Support for the Mitsubishi M52790 A/V switch. | |
| To compile this driver as a module, choose M here: the | |
| module will be called m52790. | |
| config VIDEO_ST_MIPID02 | |
| tristate "STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge" | |
| depends on I2C && VIDEO_DEV | |
| select MEDIA_CONTROLLER | |
| select VIDEO_V4L2_SUBDEV_API | |
| select V4L2_CCI_I2C | |
| select V4L2_FWNODE | |
| help | |
| Support for STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge. | |
| It is used to allow usage of CSI-2 sensor with PARALLEL port | |
| controller. | |
| To compile this driver as a module, choose M here: the | |
| module will be called st-mipid02. | |
| config VIDEO_THS7303 | |
| tristate "THS7303/53 Video Amplifier" | |
| depends on VIDEO_DEV && I2C | |
| select V4L2_ASYNC | |
| help | |
| Support for TI THS7303/53 video amplifier | |
| To compile this driver as a module, choose M here: the | |
| module will be called ths7303. | |
| endmenu | |
| # | |
| # Video serializers and deserializers (e.g. FPD-Link) | |
| # | |
| menu "Video serializers and deserializers" | |
| config VIDEO_DS90UB913 | |
| tristate "TI DS90UB913 FPD-Link III Serializer" | |
| depends on OF && I2C && VIDEO_DEV && COMMON_CLK | |
| select I2C_ATR | |
| select MEDIA_CONTROLLER | |
| select GPIOLIB | |
| select REGMAP_I2C | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| Device driver for the Texas Instruments DS90UB913 | |
| FPD-Link III Serializer. | |
| config VIDEO_DS90UB953 | |
| tristate "TI FPD-Link III/IV CSI-2 Serializers" | |
| depends on OF && I2C && VIDEO_DEV && COMMON_CLK | |
| select I2C_ATR | |
| select MEDIA_CONTROLLER | |
| select GPIOLIB | |
| select REGMAP_I2C | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| Device driver for the Texas Instruments DS90UB953 | |
| FPD-Link III Serializer and DS90UB971 FPD-Link IV Serializer. | |
| config VIDEO_DS90UB960 | |
| tristate "TI FPD-Link III/IV Deserializers" | |
| depends on OF && I2C && VIDEO_DEV && COMMON_CLK | |
| select I2C_ATR | |
| select MEDIA_CONTROLLER | |
| select GPIOLIB | |
| select REGMAP_I2C | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| Device driver for the Texas Instruments DS90UB954, DS90UB960 | |
| FPD-Link III Deserializers and DS90UB9702 FPD-Link IV Deserializer. | |
| config VIDEO_MAX96714 | |
| tristate "Maxim MAX96714 GMSL2 deserializer" | |
| depends on OF && I2C && VIDEO_DEV | |
| select I2C_MUX | |
| select MEDIA_CONTROLLER | |
| select GPIOLIB | |
| select V4L2_CCI_I2C | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| Device driver for the Maxim MAX96714 GMSL2 Deserializer. | |
| MAX96714 deserializers convert a GMSL2 input to MIPI CSI-2 | |
| output. | |
| To compile this driver as a module, choose M here: the | |
| module will be called max96714. | |
| config VIDEO_MAX96717 | |
| tristate "Maxim MAX96717 GMSL2 Serializer support" | |
| depends on I2C && VIDEO_DEV && COMMON_CLK | |
| select I2C_MUX | |
| select MEDIA_CONTROLLER | |
| select GPIOLIB | |
| select V4L2_CCI_I2C | |
| select V4L2_FWNODE | |
| select VIDEO_V4L2_SUBDEV_API | |
| help | |
| Device driver for the Maxim MAX96717 GMSL2 Serializer. | |
| MAX96717 serializers convert video on a MIPI CSI-2 | |
| input to a GMSL2 output. | |
| To compile this driver as a module, choose M here: the | |
| module will be called max96717. | |
| endmenu | |
| endif # VIDEO_DEV |